Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
diff --git a/Documentation/devicetree/bindings/arm/omap/prm-inst.txt b/Documentation/devicetree/bindings/arm/omap/prm-inst.txt
index fcd3456..42db138 100644
--- a/Documentation/devicetree/bindings/arm/omap/prm-inst.txt
+++ b/Documentation/devicetree/bindings/arm/omap/prm-inst.txt
@@ -18,6 +18,7 @@
(base address and length)
Optional properties:
+- #power-domain-cells: Should be 0 if the instance is a power domain provider.
- #reset-cells: Should be 1 if the PRM instance in question supports resets.
Example:
@@ -25,5 +26,6 @@
prm_dsp2: prm@1b00 {
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
reg = <0x1b00 0x40>;
+ #power-domain-cells = <0>;
#reset-cells = <1>;
};
diff --git a/MAINTAINERS b/MAINTAINERS
index 8e4daa9..0b2423a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2199,8 +2199,8 @@
L: openmoko-kernel@lists.openmoko.org (subscribers-only)
S: Orphan
W: http://wiki.openmoko.org/wiki/Neo_FreeRunner
-F: arch/arm/mach-s3c24xx/gta02.h
-F: arch/arm/mach-s3c24xx/mach-gta02.c
+F: arch/arm/mach-s3c/gta02.h
+F: arch/arm/mach-s3c/mach-gta02.c
ARM/Orion SoC/Technologic Systems TS-78xx platform support
M: Alexander Clouter <alex@digriz.org.uk>
@@ -2379,7 +2379,7 @@
M: Kukjin Kim <kgene@kernel.org>
M: Krzysztof Kozlowski <krzk@kernel.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Maintained
Q: https://patchwork.kernel.org/project/linux-samsung-soc/list/
F: Documentation/arm/samsung/
@@ -2389,10 +2389,8 @@
F: arch/arm/boot/dts/s3c*
F: arch/arm/boot/dts/s5p*
F: arch/arm/mach-exynos*/
-F: arch/arm/mach-s3c24*/
-F: arch/arm/mach-s3c64xx/
+F: arch/arm/mach-s3c/
F: arch/arm/mach-s5p*/
-F: arch/arm/plat-samsung/
F: arch/arm64/boot/dts/exynos/
F: drivers/*/*/*s3c24*
F: drivers/*/*s3c24*
@@ -2403,6 +2401,9 @@
F: drivers/tty/serial/samsung*
F: include/linux/soc/samsung/
N: exynos
+N: s3c2410
+N: s3c64xx
+N: s5pv210
ARM/SAMSUNG MOBILE MACHINE SUPPORT
M: Kyungmin Park <kyungmin.park@samsung.com>
@@ -2421,7 +2422,7 @@
ARM/SAMSUNG S5P SERIES HDMI CEC SUBSYSTEM SUPPORT
M: Marek Szyprowski <m.szyprowski@samsung.com>
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
L: linux-media@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/media/s5p-cec.txt
@@ -3415,7 +3416,7 @@
L: linux-arm-kernel@lists.infradead.org
S: Maintained
F: arch/arm/boot/dts/bcm470*
-F: arch/arm/boot/dts/bcm5301x*.dtsi
+F: arch/arm/boot/dts/bcm5301*
F: arch/arm/boot/dts/bcm953012*
F: arch/arm/mach-bcm/bcm_5301x.c
@@ -13447,7 +13448,7 @@
M: Jingoo Han <jingoohan1@gmail.com>
L: linux-pci@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Maintained
F: drivers/pci/controller/dwc/pci-exynos.c
@@ -13854,7 +13855,7 @@
M: Krzysztof Kozlowski <krzk@kernel.org>
M: Sylwester Nawrocki <s.nawrocki@samsung.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Maintained
Q: https://patchwork.kernel.org/project/linux-samsung-soc/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung.git
@@ -15415,7 +15416,7 @@
SAMSUNG S3C24XX/S3C64XX SOC SERIES CAMIF DRIVER
M: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
L: linux-media@vger.kernel.org
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Maintained
F: drivers/media/platform/s3c-camif/
F: include/media/drv-intf/s3c_camif.h
@@ -15465,7 +15466,7 @@
M: Sylwester Nawrocki <s.nawrocki@samsung.com>
M: Tomasz Figa <tomasz.figa@gmail.com>
M: Chanwoo Choi <cw00.choi@samsung.com>
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Supported
T: git git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk.git
F: Documentation/devicetree/bindings/clock/exynos*.txt
@@ -15473,17 +15474,20 @@
F: Documentation/devicetree/bindings/clock/samsung,s5p*
F: drivers/clk/samsung/
F: include/dt-bindings/clock/exynos*.h
+F: include/linux/clk/samsung.h
+F: include/linux/platform_data/clk-s3c2410.h
SAMSUNG SPI DRIVERS
M: Kukjin Kim <kgene@kernel.org>
M: Krzysztof Kozlowski <krzk@kernel.org>
M: Andi Shyti <andi@etezian.org>
L: linux-spi@vger.kernel.org
-L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
+L: linux-samsung-soc@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/spi/spi-samsung.txt
F: drivers/spi/spi-s3c*
F: include/linux/platform_data/spi-s3c64xx.h
+F: include/linux/spi/s3c24xx-fiq.h
SAMSUNG SXGBE DRIVERS
M: Byungho An <bh74.an@samsung.com>
@@ -16001,19 +16005,17 @@
F: include/linux/platform_data/simplefb.h
SIMTEC EB110ATX (Chalice CATS)
-M: Vincent Sanders <vince@simtec.co.uk>
M: Simtec Linux Team <linux@simtec.co.uk>
S: Supported
W: http://www.simtec.co.uk/products/EB110ATX/
SIMTEC EB2410ITX (BAST)
-M: Vincent Sanders <vince@simtec.co.uk>
M: Simtec Linux Team <linux@simtec.co.uk>
S: Supported
W: http://www.simtec.co.uk/products/EB2410ITX/
-F: arch/arm/mach-s3c24xx/bast-ide.c
-F: arch/arm/mach-s3c24xx/bast-irq.c
-F: arch/arm/mach-s3c24xx/mach-bast.c
+F: arch/arm/mach-s3c/bast-ide.c
+F: arch/arm/mach-s3c/bast-irq.c
+F: arch/arm/mach-s3c/mach-bast.c
SIOX
M: Thorsten Scherer <t.scherer@eckelmann.de>
@@ -18952,7 +18954,7 @@
F: Documentation/devicetree/bindings/regulator/wlf,arizona.yaml
F: Documentation/devicetree/bindings/sound/wlf,arizona.yaml
F: Documentation/hwmon/wm83??.rst
-F: arch/arm/mach-s3c64xx/mach-crag6410*
+F: arch/arm/mach-s3c/mach-crag6410*
F: drivers/clk/clk-wm83*.c
F: drivers/extcon/extcon-arizona.c
F: drivers/gpio/gpio-*wm*.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c18fa9d..fe2f17eb2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -268,9 +268,7 @@
depends on !ARM_PATCH_PHYS_VIRT
default DRAM_BASE if !MMU
default 0x00000000 if ARCH_EBSA110 || \
- ARCH_FOOTBRIDGE || \
- ARCH_INTEGRATOR || \
- ARCH_REALVIEW
+ ARCH_FOOTBRIDGE
default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
default 0x20000000 if ARCH_S5PV210
default 0xc0000000 if ARCH_SA1100
@@ -506,11 +504,12 @@
select GPIOLIB
select GENERIC_IRQ_MULTI_HANDLER
select HAVE_S3C2410_I2C if I2C
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select NEED_MACH_IO_H
+ select S3C2410_WATCHDOG
select SAMSUNG_ATAGS
select USE_OF
+ select WATCHDOG
help
Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
@@ -639,7 +638,6 @@
source "arch/arm/mach-ep93xx/Kconfig"
source "arch/arm/mach-exynos/Kconfig"
-source "arch/arm/plat-samsung/Kconfig"
source "arch/arm/mach-footbridge/Kconfig"
@@ -712,9 +710,7 @@
source "arch/arm/mach-rockchip/Kconfig"
-source "arch/arm/mach-s3c24xx/Kconfig"
-
-source "arch/arm/mach-s3c64xx/Kconfig"
+source "arch/arm/mach-s3c/Kconfig"
source "arch/arm/mach-s5pv210/Kconfig"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 87912e5..8986a91 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -1005,7 +1005,7 @@
via SCIFA4 on Renesas SH-Mobile AG5 (SH73A0).
config DEBUG_S3C_UART0
- depends on PLAT_SAMSUNG
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1017,7 +1017,7 @@
by the boot-loader before use.
config DEBUG_S3C_UART1
- depends on PLAT_SAMSUNG
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1029,7 +1029,7 @@
by the boot-loader before use.
config DEBUG_S3C_UART2
- depends on PLAT_SAMSUNG
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1041,7 +1041,7 @@
by the boot-loader before use.
config DEBUG_S3C_UART3
- depends on PLAT_SAMSUNG && (ARCH_EXYNOS || ARCH_S5PV210)
+ depends on ARCH_EXYNOS || ARCH_S5PV210
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C64XX_UART if ARCH_S3C64XX
select DEBUG_S5PV210_UART if ARCH_S5PV210
@@ -1086,6 +1086,14 @@
on SA-11x0 UART ports. The kernel will check for the first
enabled UART in a sequence 3-1-2.
+ config DEBUG_SD5203_UART
+ bool "Hisilicon SD5203 Debug UART"
+ depends on ARCH_SD5203
+ select DEBUG_UART_8250
+ help
+ Say Y here if you want kernel low-level debugging support
+ on SD5203 UART.
+
config DEBUG_SOCFPGA_UART0
depends on ARCH_SOCFPGA
bool "Use SOCFPGA UART0 for low-level debug"
@@ -1497,6 +1505,16 @@
config DEBUG_S5PV210_UART
bool
+config DEBUG_S3C_UART
+ depends on DEBUG_S3C2410_UART || DEBUG_S3C24XX_UART || \
+ DEBUG_S3C64XX_UART || DEBUG_S5PV210_UART || \
+ DEBUG_EXYNOS_UART
+ int
+ default "0" if DEBUG_S3C_UART0
+ default "1" if DEBUG_S3C_UART1
+ default "2" if DEBUG_S3C_UART2
+ default "3" if DEBUG_S3C_UART3
+
config DEBUG_OMAP2PLUS_UART
bool
depends on ARCH_OMAP2PLUS
@@ -1650,6 +1668,7 @@
default 0x11006000 if DEBUG_MT6589_UART0
default 0x11009000 if DEBUG_MT8135_UART3
default 0x16000000 if DEBUG_INTEGRATOR
+ default 0x1600d000 if DEBUG_SD5203_UART
default 0x18000300 if DEBUG_BCM_5301X
default 0x18000400 if DEBUG_BCM_HR2
default 0x18010000 if DEBUG_SIRFATLAS7_UART0
@@ -1852,7 +1871,7 @@
default 0xfec60000 if DEBUG_SIRFPRIMA2_UART1
default 0xfec90000 if DEBUG_RK32_UART2
default 0xfed0c000 if DEBUG_DAVINCI_DA8XX_UART1
- default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2
+ default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_SD5203_UART
default 0xfed60000 if DEBUG_RK29_UART0
default 0xfed64000 if DEBUG_RK29_UART1 || DEBUG_RK3X_UART2
default 0xfed68000 if DEBUG_RK29_UART2 || DEBUG_RK3X_UART3
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 2874cd9..4d76eab 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -212,8 +212,7 @@
machine-$(CONFIG_ARCH_REALVIEW) += realview
machine-$(CONFIG_ARCH_ROCKCHIP) += rockchip
machine-$(CONFIG_ARCH_RPC) += rpc
-machine-$(CONFIG_ARCH_S3C24XX) += s3c24xx
-machine-$(CONFIG_ARCH_S3C64XX) += s3c64xx
+machine-$(CONFIG_PLAT_SAMSUNG) += s3c
machine-$(CONFIG_ARCH_S5PV210) += s5pv210
machine-$(CONFIG_ARCH_SA1100) += sa1100
machine-$(CONFIG_ARCH_RENESAS) += shmobile
@@ -235,13 +234,9 @@
# Platform directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_EXYNOS) += samsung
plat-$(CONFIG_ARCH_OMAP) += omap
-plat-$(CONFIG_ARCH_S3C64XX) += samsung
-plat-$(CONFIG_ARCH_S5PV210) += samsung
plat-$(CONFIG_PLAT_ORION) += orion
plat-$(CONFIG_PLAT_PXA) += pxa
-plat-$(CONFIG_PLAT_S3C24XX) += samsung
plat-$(CONFIG_PLAT_VERSATILE) += versatile
ifeq ($(CONFIG_ARCH_EBSA110),y)
diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi
index b88d0caa..ea20e4b 100644
--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@@ -425,7 +425,6 @@ target-module@39000 { /* 0x44e39000, ap 33 02.0 */
target-module@3e000 { /* 0x44e3e000, ap 35 60.0 */
compatible = "ti,sysc-omap4-simple", "ti,sysc";
- ti,hwmods = "rtc";
reg = <0x3e074 0x4>,
<0x3e078 0x4>;
reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 5cb4cc3..0fab080 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -578,6 +578,7 @@ target-module@56000000 {
<SYSC_IDLE_SMART>;
clocks = <&gfx_l3_clkctrl AM3_GFX_L3_GFX_CLKCTRL 0>;
clock-names = "fck";
+ power-domains = <&prm_gfx>;
resets = <&prm_gfx 0>;
reset-names = "rstctrl";
#address-cells = <1>;
@@ -617,6 +618,7 @@ prm_device: prm@f00 {
prm_gfx: prm@1100 {
compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
reg = <0x1100 0x100>;
+ #power-domain-cells = <0>;
#reset-cells = <1>;
};
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 1431404..8d47913 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -517,6 +517,7 @@ target-module@56000000 {
<SYSC_IDLE_SMART>;
clocks = <&gfx_l3_clkctrl AM4_GFX_L3_GFX_CLKCTRL 0>;
clock-names = "fck";
+ power-domains = <&prm_gfx>;
resets = <&prm_gfx 0>;
reset-names = "rstctrl";
#address-cells = <1>;
@@ -533,6 +534,7 @@ &prcm {
prm_gfx: prm@400 {
compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
reg = <0x400 0x100>;
+ #power-domain-cells = <0>;
#reset-cells = <1>;
};
diff --git a/arch/arm/boot/dts/am437x-l4.dtsi b/arch/arm/boot/dts/am437x-l4.dtsi
index 3d393fe..8a67bb2 100644
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/am437x-l4.dtsi
@@ -409,9 +409,8 @@ target-module@39000 { /* 0x44e39000, ap 32 02.0 */
ranges = <0x0 0x39000 0x1000>;
};
- target-module@3e000 { /* 0x44e3e000, ap 34 60.0 */
+ rtc_target: target-module@3e000 { /* 0x44e3e000, ap 34 60.0 */
compatible = "ti,sysc-omap4-simple", "ti,sysc";
- ti,hwmods = "rtc";
reg = <0x3e074 0x4>,
<0x3e078 0x4>;
reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index de4fc78..7f3faa3 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -833,6 +833,10 @@ &epwmss0 {
status = "okay";
};
+&rtc_target {
+ status = "disabled";
+};
+
&tscadc {
status = "okay";
diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi
index 27a6a83..f43b764 100644
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/dra7-l4.dtsi
@@ -3561,7 +3561,6 @@ timer16: timer@0 {
rtctarget: target-module@38000 { /* 0x48838000, ap 29 12.0 */
compatible = "ti,sysc-omap4-simple", "ti,sysc";
- ti,hwmods = "rtcss";
reg = <0x38074 0x4>,
<0x38078 0x4>;
reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/omap4-l4-abe.dtsi b/arch/arm/boot/dts/omap4-l4-abe.dtsi
index b2cf5f4..a9573d4 100644
--- a/arch/arm/boot/dts/omap4-l4-abe.dtsi
+++ b/arch/arm/boot/dts/omap4-l4-abe.dtsi
@@ -1,14 +1,16 @@
&l4_abe { /* 0x40100000 */
- compatible = "ti,omap4-l4-abe", "simple-bus";
+ compatible = "ti,omap4-l4-abe", "simple-pm-bus";
reg = <0x40100000 0x400>,
<0x40100400 0x400>;
reg-names = "la", "ap";
+ power-domains = <&prm_abe>;
+ /* OMAP4_L4_ABE_CLKCTRL is read-only */
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x40100000 0x100000>, /* segment 0 */
<0x49000000 0x49000000 0x100000>;
segment@0 { /* 0x40100000 */
- compatible = "simple-bus";
+ compatible = "simple-pm-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges =
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 0282b9d..eb5780eb 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -658,6 +658,12 @@ prm_tesla: prm@400 {
#reset-cells = <1>;
};
+ prm_abe: prm@500 {
+ compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+ reg = <0x500 0x100>;
+ #power-domain-cells = <0>;
+ };
+
prm_core: prm@700 {
compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
reg = <0x700 0x100>;
diff --git a/arch/arm/boot/dts/omap5-l4-abe.dtsi b/arch/arm/boot/dts/omap5-l4-abe.dtsi
index 25b7fce..a03bca5 100644
--- a/arch/arm/boot/dts/omap5-l4-abe.dtsi
+++ b/arch/arm/boot/dts/omap5-l4-abe.dtsi
@@ -1,14 +1,16 @@
&l4_abe { /* 0x40100000 */
- compatible = "ti,omap5-l4-abe", "simple-bus";
+ compatible = "ti,omap5-l4-abe", "simple-pm-bus";
reg = <0x40100000 0x400>,
<0x40100400 0x400>;
reg-names = "la", "ap";
+ power-domains = <&prm_abe>;
+ /* OMAP5_L4_ABE_CLKCTRL is read-only */
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x40100000 0x100000>, /* segment 0 */
<0x49000000 0x49000000 0x100000>;
segment@0 { /* 0x40100000 */
- compatible = "simple-bus";
+ compatible = "simple-pm-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges =
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index a82c962..2bf2e58 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -676,6 +676,12 @@ prm_dsp: prm@400 {
#reset-cells = <1>;
};
+ prm_abe: prm@500 {
+ compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+ reg = <0x500 0x100>;
+ #power-domain-cells = <0>;
+ };
+
prm_core: prm@700 {
compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
reg = <0x700 0x100>;
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index f5f1111..aeb1209 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -20,9 +20,9 @@
CONFIG_MACH_MX27_3DS=y
CONFIG_MACH_IMX27_VISSTRIM_M10=y
CONFIG_MACH_PCA100=y
-CONFIG_MACH_IMX27_DT=y
CONFIG_SOC_IMX1=y
CONFIG_SOC_IMX25=y
+CONFIG_SOC_IMX27=y
CONFIG_AEABI=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 82d3ffb..e1d8301 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -15,20 +15,8 @@
# CONFIG_COMPAT_BRK is not set
CONFIG_ARCH_MULTI_V6=y
CONFIG_ARCH_MXC=y
-CONFIG_MACH_MX31LILLY=y
-CONFIG_MACH_MX31LITE=y
-CONFIG_MACH_PCM037=y
-CONFIG_MACH_PCM037_EET=y
-CONFIG_MACH_MX31_3DS=y
-CONFIG_MACH_MX31MOBOARD=y
-CONFIG_MACH_QONG=y
-CONFIG_MACH_ARMADILLO5X0=y
-CONFIG_MACH_KZM_ARM11_01=y
-CONFIG_MACH_IMX31_DT=y
-CONFIG_MACH_IMX35_DT=y
-CONFIG_MACH_PCM043=y
-CONFIG_MACH_MX35_3DS=y
-CONFIG_MACH_VPR200=y
+CONFIG_SOC_IMX31=y
+CONFIG_SOC_IMX35=y
CONFIG_SOC_IMX50=y
CONFIG_SOC_IMX51=y
CONFIG_SOC_IMX53=y
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index 2724fb3..70b709a 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -29,8 +29,8 @@
CONFIG_MACH_MX27_3DS=y
CONFIG_MACH_IMX27_VISSTRIM_M10=y
CONFIG_MACH_PCA100=y
-CONFIG_MACH_IMX27_DT=y
CONFIG_SOC_IMX25=y
+CONFIG_SOC_IMX27=y
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
CONFIG_ARCH_ORION5X=y
diff --git a/arch/arm/include/debug/brcmstb.S b/arch/arm/include/debug/brcmstb.S
index 7ffe669..0ff32ff 100644
--- a/arch/arm/include/debug/brcmstb.S
+++ b/arch/arm/include/debug/brcmstb.S
@@ -32,6 +32,8 @@
#define UARTA_7271 UARTA_7268
#define UARTA_7278 REG_PHYS_ADDR_V7(0x40c000)
#define UARTA_7216 UARTA_7278
+#define UARTA_72164 UARTA_7278
+#define UARTA_72165 UARTA_7278
#define UARTA_7364 REG_PHYS_ADDR(0x40b000)
#define UARTA_7366 UARTA_7364
#define UARTA_74371 REG_PHYS_ADDR(0x406b00)
@@ -84,17 +86,19 @@
/* Chip specific detection starts here */
20: checkuart(\rp, \rv, 0x33900000, 3390)
21: checkuart(\rp, \rv, 0x72160000, 7216)
-22: checkuart(\rp, \rv, 0x72500000, 7250)
-23: checkuart(\rp, \rv, 0x72550000, 7255)
-24: checkuart(\rp, \rv, 0x72600000, 7260)
-25: checkuart(\rp, \rv, 0x72680000, 7268)
-26: checkuart(\rp, \rv, 0x72710000, 7271)
-27: checkuart(\rp, \rv, 0x72780000, 7278)
-28: checkuart(\rp, \rv, 0x73640000, 7364)
-29: checkuart(\rp, \rv, 0x73660000, 7366)
-30: checkuart(\rp, \rv, 0x07437100, 74371)
-31: checkuart(\rp, \rv, 0x74390000, 7439)
-32: checkuart(\rp, \rv, 0x74450000, 7445)
+22: checkuart(\rp, \rv, 0x07216400, 72164)
+23: checkuart(\rp, \rv, 0x07216500, 72165)
+24: checkuart(\rp, \rv, 0x72500000, 7250)
+25: checkuart(\rp, \rv, 0x72550000, 7255)
+26: checkuart(\rp, \rv, 0x72600000, 7260)
+27: checkuart(\rp, \rv, 0x72680000, 7268)
+28: checkuart(\rp, \rv, 0x72710000, 7271)
+29: checkuart(\rp, \rv, 0x72780000, 7278)
+30: checkuart(\rp, \rv, 0x73640000, 7364)
+31: checkuart(\rp, \rv, 0x73660000, 7366)
+32: checkuart(\rp, \rv, 0x07437100, 74371)
+33: checkuart(\rp, \rv, 0x74390000, 7439)
+34: checkuart(\rp, \rv, 0x74450000, 7445)
/* No valid UART found */
90: mov \rp, #0
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 2aab043..120f9aa 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -51,10 +51,11 @@ static struct at91_soc_pm soc_pm = {
};
static const match_table_t pm_modes __initconst = {
- { AT91_PM_STANDBY, "standby" },
- { AT91_PM_ULP0, "ulp0" },
- { AT91_PM_ULP1, "ulp1" },
- { AT91_PM_BACKUP, "backup" },
+ { AT91_PM_STANDBY, "standby" },
+ { AT91_PM_ULP0, "ulp0" },
+ { AT91_PM_ULP0_FAST, "ulp0-fast" },
+ { AT91_PM_ULP1, "ulp1" },
+ { AT91_PM_BACKUP, "backup" },
{ -1, NULL },
};
@@ -557,11 +558,6 @@ static void at91rm9200_idle(void)
writel(AT91_PMC_PCK, soc_pm.data.pmc + AT91_PMC_SCDR);
}
-static void at91sam9x60_idle(void)
-{
- cpu_do_idle();
-}
-
static void at91sam9_idle(void)
{
writel(AT91_PMC_PCK, soc_pm.data.pmc + AT91_PMC_SCDR);
@@ -789,6 +785,51 @@ static const struct of_device_id atmel_pmc_ids[] __initconst = {
{ /* sentinel */ },
};
+static void __init at91_pm_modes_validate(const int *modes, int len)
+{
+ u8 i, standby = 0, suspend = 0;
+ int mode;
+
+ for (i = 0; i < len; i++) {
+ if (standby && suspend)
+ break;
+
+ if (modes[i] == soc_pm.data.standby_mode && !standby) {
+ standby = 1;
+ continue;
+ }
+
+ if (modes[i] == soc_pm.data.suspend_mode && !suspend) {
+ suspend = 1;
+ continue;
+ }
+ }
+
+ if (!standby) {
+ if (soc_pm.data.suspend_mode == AT91_PM_STANDBY)
+ mode = AT91_PM_ULP0;
+ else
+ mode = AT91_PM_STANDBY;
+
+ pr_warn("AT91: PM: %s mode not supported! Using %s.\n",
+ pm_modes[soc_pm.data.standby_mode].pattern,
+ pm_modes[mode].pattern);
+ soc_pm.data.standby_mode = mode;
+ }
+
+ if (!suspend) {
+ if (soc_pm.data.standby_mode == AT91_PM_ULP0)
+ mode = AT91_PM_STANDBY;
+ else
+ mode = AT91_PM_ULP0;
+
+ pr_warn("AT91: PM: %s mode not supported! Using %s.\n",
+ pm_modes[soc_pm.data.suspend_mode].pattern,
+ pm_modes[mode].pattern);
+ soc_pm.data.suspend_mode = mode;
+ }
+}
+
static void __init at91_pm_init(void (*pm_idle)(void))
{
struct device_node *pmc_np;
@@ -800,6 +841,7 @@ static void __init at91_pm_init(void (*pm_idle)(void))
pmc_np = of_find_matching_node_and_match(NULL, atmel_pmc_ids, &of_id);
soc_pm.data.pmc = of_iomap(pmc_np, 0);
+ of_node_put(pmc_np);
if (!soc_pm.data.pmc) {
pr_err("AT91: PM not supported, PMC not found\n");
return;
@@ -830,6 +872,14 @@ void __init at91rm9200_pm_init(void)
if (!IS_ENABLED(CONFIG_SOC_AT91RM9200))
return;
+ /*
+ * Force STANDBY and ULP0 mode to avoid calling
+ * at91_pm_modes_validate() which may increase booting time.
+ * Platform supports anyway only STANDBY and ULP0 modes.
+ */
+ soc_pm.data.standby_mode = AT91_PM_STANDBY;
+ soc_pm.data.suspend_mode = AT91_PM_ULP0;
+
at91_dt_ramc();
/*
@@ -842,12 +892,17 @@ void __init at91rm9200_pm_init(void)
void __init sam9x60_pm_init(void)
{
+ static const int modes[] __initconst = {
+ AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST, AT91_PM_ULP1,
+ };
+
if (!IS_ENABLED(CONFIG_SOC_SAM9X60))
return;
+ at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
at91_pm_modes_init();
at91_dt_ramc();
- at91_pm_init(at91sam9x60_idle);
+ at91_pm_init(NULL);
soc_pm.ws_ids = sam9x60_ws_ids;
soc_pm.config_pmc_ws = at91_sam9x60_config_pmc_ws;
@@ -858,26 +913,46 @@ void __init at91sam9_pm_init(void)
if (!IS_ENABLED(CONFIG_SOC_AT91SAM9))
return;
+ /*
+ * Force STANDBY and ULP0 mode to avoid calling
+ * at91_pm_modes_validate() which may increase booting time.
+ * Platform supports anyway only STANDBY and ULP0 modes.
+ */
+ soc_pm.data.standby_mode = AT91_PM_STANDBY;
+ soc_pm.data.suspend_mode = AT91_PM_ULP0;
+
at91_dt_ramc();
at91_pm_init(at91sam9_idle);
}
void __init sama5_pm_init(void)
{
+ static const int modes[] __initconst = {
+ AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST,
+ };
+
if (!IS_ENABLED(CONFIG_SOC_SAMA5))
return;
+ at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
at91_dt_ramc();
at91_pm_init(NULL);
}
void __init sama5d2_pm_init(void)
{
+ static const int modes[] __initconst = {
+ AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST, AT91_PM_ULP1,
+ AT91_PM_BACKUP,
+ };
+
if (!IS_ENABLED(CONFIG_SOC_SAMA5D2))
return;
+ at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
at91_pm_modes_init();
- sama5_pm_init();
+ at91_dt_ramc();
+ at91_pm_init(NULL);
soc_pm.ws_ids = sama5d2_ws_ids;
soc_pm.config_shdwc_ws = at91_sama5d2_config_shdwc_ws;
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index 218e8d1..bfb260b 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -19,8 +19,9 @@
#define AT91_PM_STANDBY 0x00
#define AT91_PM_ULP0 0x01
-#define AT91_PM_ULP1 0x02
-#define AT91_PM_BACKUP 0x03
+#define AT91_PM_ULP0_FAST 0x02
+#define AT91_PM_ULP1 0x03
+#define AT91_PM_BACKUP 0x04
#ifndef __ASSEMBLY__
struct at91_pm_data {
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index be9764e..0184de0 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -164,7 +164,22 @@
.macro at91_pm_ulp0_mode
ldr pmc, .pmc_base
+ ldr tmp2, .pm_mode
+ ldr tmp3, .mckr_offset
+ /* Check if ULP0 fast variant has been requested. */
+ cmp tmp2, #AT91_PM_ULP0_FAST
+ bne 0f
+
+ /* Set highest prescaler for power saving */
+ ldr tmp1, [pmc, tmp3]
+ bic tmp1, tmp1, #AT91_PMC_PRES
+ orr tmp1, tmp1, #AT91_PMC_PRES_64
+ str tmp1, [pmc, tmp3]
+ wait_mckrdy
+ b 1f
+
+0:
/* Turn off the crystal oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
bic tmp1, tmp1, #AT91_PMC_MOSCEN
@@ -192,7 +207,18 @@
/* Wait for interrupt */
1: at91_cpu_idle
- /* Restore RC oscillator state */
+ /* Check if ULP0 fast variant has been requested. */
+ cmp tmp2, #AT91_PM_ULP0_FAST
+ bne 5f
+
+ /* Set lowest prescaler for fast resume. */
+ ldr tmp1, [pmc, tmp3]
+ bic tmp1, tmp1, #AT91_PMC_PRES
+ str tmp1, [pmc, tmp3]
+ wait_mckrdy
+ b 6f
+
+5: /* Restore RC oscillator state */
ldr tmp1, .saved_osc_status
tst tmp1, #AT91_PMC_MOSCRCS
beq 4f
@@ -216,6 +242,7 @@
str tmp1, [pmc, #AT91_CKGR_MOR]
wait_moscrdy
+6:
.endm
/**
@@ -473,23 +500,29 @@
ENTRY(at91_ulp_mode)
ldr pmc, .pmc_base
ldr tmp2, .mckr_offset
+ ldr tmp3, .pm_mode
/* Save Master clock setting */
ldr tmp1, [pmc, tmp2]
str tmp1, .saved_mckr
/*
- * Set the Master clock source to slow clock
+ * Set master clock source to:
+ * - MAINCK if using ULP0 fast variant
+ * - slow clock, otherwise
*/
bic tmp1, tmp1, #AT91_PMC_CSS
+ cmp tmp3, #AT91_PM_ULP0_FAST
+ bne save_mck
+ orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
+save_mck:
str tmp1, [pmc, tmp2]
wait_mckrdy
at91_plla_disable
- ldr r0, .pm_mode
- cmp r0, #AT91_PM_ULP1
+ cmp tmp3, #AT91_PM_ULP1
beq ulp1_mode
at91_pm_ulp0_mode
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index 1df0ee0..ae79090 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -208,6 +208,7 @@
select ARM_GIC
select ARM_ERRATA_798181 if SMP
select HAVE_ARM_ARCH_TIMER
+ select BCM7038_L1_IRQ
select BRCMSTB_L2_IRQ
select BCM7120_L2_IRQ
select ARCH_HAS_HOLES_MEMORYMODEL
diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
index bcb3c40..7755ccc 100644
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ b/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -548,8 +548,7 @@ static const struct property_entry eeprom_properties[] = {
*/
static struct i2c_client *dm6446evm_msp;
-static int dm6446evm_msp_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+static int dm6446evm_msp_probe(struct i2c_client *client)
{
dm6446evm_msp = client;
return 0;
@@ -569,7 +568,7 @@ static const struct i2c_device_id dm6446evm_msp_ids[] = {
static struct i2c_driver dm6446evm_msp_driver = {
.driver.name = "dm6446evm_msp",
.id_table = dm6446evm_msp_ids,
- .probe = dm6446evm_msp_probe,
+ .probe_new = dm6446evm_msp_probe,
.remove = dm6446evm_msp_remove,
};
diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
index 8319a60..952ddab 100644
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ b/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -160,8 +160,7 @@ static struct platform_device davinci_aemif_device = {
#define DM646X_EVM_ATA_PWD BIT(1)
/* CPLD Register 0 Client: used for I/O Control */
-static int cpld_reg0_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+static int cpld_reg0_probe(struct i2c_client *client)
{
if (HAS_ATA) {
u8 data;
@@ -197,7 +196,7 @@ static const struct i2c_device_id cpld_reg_ids[] = {
static struct i2c_driver dm6467evm_cpld_driver = {
.driver.name = "cpld_reg0",
.id_table = cpld_reg_ids,
- .probe = cpld_reg0_probe,
+ .probe_new = cpld_reg0_probe,
};
/* LEDS */
@@ -397,8 +396,7 @@ static struct snd_platform_data dm646x_evm_snd_data[] = {
#ifdef CONFIG_I2C
static struct i2c_client *cpld_client;
-static int cpld_video_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+static int cpld_video_probe(struct i2c_client *client)
{
cpld_client = client;
return 0;
@@ -419,7 +417,7 @@ static struct i2c_driver cpld_video_driver = {
.driver = {
.name = "cpld_video",
},
- .probe = cpld_video_probe,
+ .probe_new = cpld_video_probe,
.remove = cpld_video_remove,
.id_table = cpld_video_id,
};
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index f185cd3..d2d2497 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -24,7 +24,6 @@
select HAVE_ARM_ARCH_TIMER if ARCH_EXYNOS5
select HAVE_ARM_SCU if SMP
select HAVE_S3C2410_I2C if I2C
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select PINCTRL
select PINCTRL_EXYNOS
diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile
index 0fd3fcf..53fa363 100644
--- a/arch/arm/mach-exynos/Makefile
+++ b/arch/arm/mach-exynos/Makefile
@@ -3,10 +3,6 @@
# Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
# http://www.samsung.com/
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
-
-# Core
-
obj-$(CONFIG_ARCH_EXYNOS) += exynos.o exynos-smc.o firmware.o
obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm.o sleep.o
diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
index afd988a..29eb075 100644
--- a/arch/arm/mach-exynos/common.h
+++ b/arch/arm/mach-exynos/common.h
@@ -24,12 +24,12 @@
#define EXYNOS5800_SOC_ID 0xE5422000
#define EXYNOS5_SOC_MASK 0xFFFFF000
-extern unsigned long samsung_cpu_id;
+extern unsigned long exynos_cpu_id;
#define IS_SAMSUNG_CPU(name, id, mask) \
static inline int is_samsung_##name(void) \
{ \
- return ((samsung_cpu_id & mask) == (id & mask)); \
+ return ((exynos_cpu_id & mask) == (id & mask)); \
}
IS_SAMSUNG_CPU(exynos3250, EXYNOS3250_SOC_ID, EXYNOS3_SOC_MASK)
@@ -147,7 +147,7 @@ extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data;
extern void exynos_set_delayed_reset_assertion(bool enable);
-extern unsigned int samsung_rev(void);
+extern unsigned int exynos_rev(void);
extern void exynos_core_restart(u32 core_id);
extern int exynos_set_boot_addr(u32 core_id, unsigned long boot_addr);
extern int exynos_get_boot_addr(u32 core_id, unsigned long *boot_addr);
diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
index 36c3744..700763e 100644
--- a/arch/arm/mach-exynos/exynos.c
+++ b/arch/arm/mach-exynos/exynos.c
@@ -19,11 +19,12 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/map.h>
-#include <plat/cpu.h>
-
#include "common.h"
+#define S3C_ADDR_BASE 0xF6000000
+#define S3C_ADDR(x) ((void __iomem __force *)S3C_ADDR_BASE + (x))
+#define S5P_VA_CHIPID S3C_ADDR(0x02000000)
+
static struct platform_device exynos_cpuidle = {
.name = "exynos_cpuidle",
#ifdef CONFIG_ARM_EXYNOS_CPUIDLE
@@ -36,6 +37,14 @@ void __iomem *sysram_base_addr __ro_after_init;
phys_addr_t sysram_base_phys __ro_after_init;
void __iomem *sysram_ns_base_addr __ro_after_init;
+unsigned long exynos_cpu_id;
+static unsigned int exynos_cpu_rev;
+
+unsigned int exynos_rev(void)
+{
+ return exynos_cpu_rev;
+}
+
void __init exynos_sysram_init(void)
{
struct device_node *node;
@@ -86,7 +95,11 @@ static void __init exynos_init_io(void)
of_scan_flat_dt(exynos_fdt_map_chipid, NULL);
/* detect cpu id and rev. */
- s5p_init_cpu(S5P_VA_CHIPID);
+ exynos_cpu_id = readl_relaxed(S5P_VA_CHIPID);
+ exynos_cpu_rev = exynos_cpu_id & 0xFF;
+
+ pr_info("Samsung CPU ID: 0x%08lx\n", exynos_cpu_id);
+
}
/*
@@ -193,8 +206,8 @@ static void __init exynos_dt_fixup(void)
}
DT_MACHINE_START(EXYNOS_DT, "Samsung Exynos (Flattened Device Tree)")
- .l2c_aux_val = 0x3c400000,
- .l2c_aux_mask = 0xc20fffff,
+ .l2c_aux_val = 0x38400000,
+ .l2c_aux_mask = 0xc60fffff,
.smp = smp_ops(exynos_smp_ops),
.map_io = exynos_init_io,
.init_early = exynos_firmware_init,
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
deleted file mode 100644
index 8d58faa..0000000
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com/
- *
- * Exynos - Memory map definitions
- */
-
-#ifndef __ASM_ARCH_MAP_H
-#define __ASM_ARCH_MAP_H __FILE__
-
-#include <plat/map-base.h>
-
-#include <plat/map-s5p.h>
-
-#define EXYNOS_PA_CHIPID 0x10000000
-
-#endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c
index 0cbbae8..d7fedbb 100644
--- a/arch/arm/mach-exynos/platsmp.c
+++ b/arch/arm/mach-exynos/platsmp.c
@@ -22,8 +22,6 @@
#include <asm/smp_scu.h>
#include <asm/firmware.h>
-#include <mach/map.h>
-
#include "common.h"
extern void exynos4_secondary_startup(void);
@@ -188,7 +186,7 @@ void exynos_scu_enable(void)
static void __iomem *cpu_boot_reg_base(void)
{
- if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1)
+ if (soc_is_exynos4210() && exynos_rev() == EXYNOS4210_REV_1_1)
return pmu_base_addr + S5P_INFORM5;
return sysram_base_addr;
}
diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
index 78af34c..30f4e55 100644
--- a/arch/arm/mach-exynos/pm.c
+++ b/arch/arm/mach-exynos/pm.c
@@ -26,18 +26,18 @@
static inline void __iomem *exynos_boot_vector_addr(void)
{
- if (samsung_rev() == EXYNOS4210_REV_1_1)
+ if (exynos_rev() == EXYNOS4210_REV_1_1)
return pmu_base_addr + S5P_INFORM7;
- else if (samsung_rev() == EXYNOS4210_REV_1_0)
+ else if (exynos_rev() == EXYNOS4210_REV_1_0)
return sysram_base_addr + 0x24;
return pmu_base_addr + S5P_INFORM0;
}
static inline void __iomem *exynos_boot_vector_flag(void)
{
- if (samsung_rev() == EXYNOS4210_REV_1_1)
+ if (exynos_rev() == EXYNOS4210_REV_1_1)
return pmu_base_addr + S5P_INFORM6;
- else if (samsung_rev() == EXYNOS4210_REV_1_0)
+ else if (exynos_rev() == EXYNOS4210_REV_1_0)
return sysram_base_addr + 0x20;
return pmu_base_addr + S5P_INFORM1;
}
diff --git a/arch/arm/mach-hisi/Kconfig b/arch/arm/mach-hisi/Kconfig
index 3b010fe..2e980f8 100644
--- a/arch/arm/mach-hisi/Kconfig
+++ b/arch/arm/mach-hisi/Kconfig
@@ -1,9 +1,9 @@
# SPDX-License-Identifier: GPL-2.0-only
config ARCH_HISI
bool "Hisilicon SoC Support"
- depends on ARCH_MULTI_V7
+ depends on ARCH_MULTI_V7 || ARCH_MULTI_V5
select ARM_AMBA
- select ARM_GIC
+ select ARM_GIC if ARCH_MULTI_V7
select ARM_TIMER_SP804
select POWER_RESET
select POWER_RESET_HISI
@@ -15,6 +15,7 @@
config ARCH_HI3xxx
bool "Hisilicon Hi36xx family"
+ depends on ARCH_MULTI_V7
select CACHE_L2X0
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
@@ -25,6 +26,7 @@
config ARCH_HIP01
bool "Hisilicon HIP01 family"
+ depends on ARCH_MULTI_V7
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
select ARM_GLOBAL_TIMER
@@ -33,6 +35,7 @@
config ARCH_HIP04
bool "Hisilicon HiP04 Cortex A15 family"
+ depends on ARCH_MULTI_V7
select ARM_ERRATA_798181 if SMP
select HAVE_ARM_ARCH_TIMER
select MCPM if SMP
@@ -43,6 +46,7 @@
config ARCH_HIX5HD2
bool "Hisilicon X5HD2 family"
+ depends on ARCH_MULTI_V7
select CACHE_L2X0
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
@@ -50,6 +54,14 @@
select PINCTRL_SINGLE
help
Support for Hisilicon HIX5HD2 SoC family
+
+config ARCH_SD5203
+ bool "Hisilicon SD5203 family"
+ depends on ARCH_MULTI_V5
+ select DW_APB_ICTL
+ help
+ Support for Hisilicon SD5203 SoC family
+
endmenu
endif
diff --git a/arch/arm/mach-imx/3ds_debugboard.c b/arch/arm/mach-imx/3ds_debugboard.c
deleted file mode 100644
index 0e01800..0000000
--- a/arch/arm/mach-imx/3ds_debugboard.c
+++ /dev/null
@@ -1,207 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2010 Jason Wang <jason77.wang@gmail.com>
- */
-
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/smsc911x.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include "3ds_debugboard.h"
-#include "hardware.h"
-
-/* LAN9217 ethernet base address */
-#define LAN9217_BASE_ADDR(n) (n + 0x0)
-/* External UART */
-#define UARTA_BASE_ADDR(n) (n + 0x8000)
-#define UARTB_BASE_ADDR(n) (n + 0x10000)
-
-#define BOARD_IO_ADDR(n) (n + 0x20000)
-/* LED switchs */
-#define LED_SWITCH_REG 0x00
-/* buttons */
-#define SWITCH_BUTTONS_REG 0x08
-/* status, interrupt */
-#define INTR_STATUS_REG 0x10
-#define INTR_MASK_REG 0x38
-#define INTR_RESET_REG 0x20
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER1_REG 0x40
-#define MAGIC_NUMBER2_REG 0x48
-/* CPLD code version */
-#define CPLD_CODE_VER_REG 0x50
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER3_REG 0x58
-/* module reset register*/
-#define MODULE_RESET_REG 0x60
-/* CPU ID and Personality ID */
-#define MCU_BOARD_ID_REG 0x68
-
-#define MXC_MAX_EXP_IO_LINES 16
-
-/* interrupts like external uart , external ethernet etc*/
-#define EXPIO_INT_ENET 0
-#define EXPIO_INT_XUART_A 1
-#define EXPIO_INT_XUART_B 2
-#define EXPIO_INT_BUTTON_A 3
-#define EXPIO_INT_BUTTON_B 4
-
-static void __iomem *brd_io;
-static struct irq_domain *domain;
-
-static struct resource smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- } , {
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
-};
-
-static struct platform_device smsc_lan9217_device = {
- .name = "smsc911x",
- .id = -1,
- .dev = {
- .platform_data = &smsc911x_config,
- },
- .num_resources = ARRAY_SIZE(smsc911x_resources),
- .resource = smsc911x_resources,
-};
-
-static void mxc_expio_irq_handler(struct irq_desc *desc)
-{
- u32 imr_val;
- u32 int_valid;
- u32 expio_irq;
-
- /* irq = gpio irq number */
- desc->irq_data.chip->irq_mask(&desc->irq_data);
-
- imr_val = imx_readw(brd_io + INTR_MASK_REG);
- int_valid = imx_readw(brd_io + INTR_STATUS_REG) & ~imr_val;
-
- expio_irq = 0;
- for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
- if ((int_valid & 1) == 0)
- continue;
- generic_handle_irq(irq_find_mapping(domain, expio_irq));
- }
-
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * Irq is an expio virtual irq number
- */
-static void expio_mask_irq(struct irq_data *d)
-{
- u16 reg;
- u32 expio = d->hwirq;
-
- reg = imx_readw(brd_io + INTR_MASK_REG);
- reg |= (1 << expio);
- imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static void expio_ack_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
-
- imx_writew(1 << expio, brd_io + INTR_RESET_REG);
- imx_writew(0, brd_io + INTR_RESET_REG);
- expio_mask_irq(d);
-}
-
-static void expio_unmask_irq(struct irq_data *d)
-{
- u16 reg;
- u32 expio = d->hwirq;
-
- reg = imx_readw(brd_io + INTR_MASK_REG);
- reg &= ~(1 << expio);
- imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
- .irq_ack = expio_ack_irq,
- .irq_mask = expio_mask_irq,
- .irq_unmask = expio_unmask_irq,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-int __init mxc_expio_init(u32 base, u32 intr_gpio)
-{
- u32 p_irq = gpio_to_irq(intr_gpio);
- int irq_base;
- int i;
-
- brd_io = ioremap(BOARD_IO_ADDR(base), SZ_4K);
- if (brd_io == NULL)
- return -ENOMEM;
-
- if ((imx_readw(brd_io + MAGIC_NUMBER1_REG) != 0xAAAA) ||
- (imx_readw(brd_io + MAGIC_NUMBER2_REG) != 0x5555) ||
- (imx_readw(brd_io + MAGIC_NUMBER3_REG) != 0xCAFE)) {
- pr_info("3-Stack Debug board not detected\n");
- iounmap(brd_io);
- brd_io = NULL;
- return -ENODEV;
- }
-
- pr_info("3-Stack Debug board detected, rev = 0x%04X\n",
- readw(brd_io + CPLD_CODE_VER_REG));
-
- /*
- * Configure INT line as GPIO input
- */
- gpio_request(intr_gpio, "expio_pirq");
- gpio_direction_input(intr_gpio);
-
- /* disable the interrupt and clear the status */
- imx_writew(0, brd_io + INTR_MASK_REG);
- imx_writew(0xFFFF, brd_io + INTR_RESET_REG);
- imx_writew(0, brd_io + INTR_RESET_REG);
- imx_writew(0x1F, brd_io + INTR_MASK_REG);
-
- irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
- WARN_ON(irq_base < 0);
-
- domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
- &irq_domain_simple_ops, NULL);
- WARN_ON(!domain);
-
- for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
- irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
- irq_clear_status_flags(i, IRQ_NOREQUEST);
- }
- irq_set_irq_type(p_irq, IRQF_TRIGGER_LOW);
- irq_set_chained_handler(p_irq, mxc_expio_irq_handler);
-
- /* Register Lan device on the debugboard */
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- smsc911x_resources[0].start = LAN9217_BASE_ADDR(base);
- smsc911x_resources[0].end = LAN9217_BASE_ADDR(base) + 0x100 - 1;
- smsc911x_resources[1].start = irq_find_mapping(domain, EXPIO_INT_ENET);
- smsc911x_resources[1].end = irq_find_mapping(domain, EXPIO_INT_ENET);
- platform_device_register(&smsc_lan9217_device);
-
- return 0;
-}
diff --git a/arch/arm/mach-imx/3ds_debugboard.h b/arch/arm/mach-imx/3ds_debugboard.h
deleted file mode 100644
index a4d04d0..0000000
--- a/arch/arm/mach-imx/3ds_debugboard.h
+++ /dev/null
@@ -1,11 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#ifndef __ASM_ARCH_MXC_3DS_DB_H__
-#define __ASM_ARCH_MXC_3DS_DB_H__
-
-extern int __init mxc_expio_init(u32 base, u32 intr_gpio);
-
-#endif /* __ASM_ARCH_MXC_3DS_DB_H__ */
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index e7d7b90..5290278 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -47,371 +47,26 @@
def_bool y if SMP
select ARCH_HAS_RESET_CONTROLLER
-config IMX_HAVE_IOMUX_V1
- bool
-
-config ARCH_MXC_IOMUX_V3
- bool
-
-config SOC_IMX21
- bool
- select CPU_ARM926T
- select IMX_HAVE_IOMUX_V1
- select MXC_AVIC
-
-config SOC_IMX27
- bool
- select CPU_ARM926T
- select IMX_HAVE_IOMUX_V1
- select MXC_AVIC
- select PINCTRL_IMX27
-
-config SOC_IMX31
- bool
- select CPU_V6
- select MXC_AVIC
-
-config SOC_IMX35
- bool
- select ARCH_MXC_IOMUX_V3
- select MXC_AVIC
- select PINCTRL_IMX35
-
-if ARCH_MULTI_V5
-
-comment "MX21 platforms:"
-
-config MACH_MX21ADS
- bool "MX21ADS platform"
- select IMX_HAVE_PLATFORM_IMX_FB
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select SOC_IMX21
- help
- Include support for MX21ADS platform. This includes specific
- configurations for the board and its peripherals.
-
-comment "MX27 platforms:"
-
-config MACH_MX27ADS
- bool "MX27ADS platform"
- select IMX_HAVE_PLATFORM_IMX_FB
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_MXC_W1
- select SOC_IMX27
- help
- Include support for MX27ADS platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_MX27_3DS
- bool "MX27PDK platform"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_FB
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_KEYPAD
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MX2_CAMERA
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_SPI_IMX
- select MXC_DEBUG_BOARD
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX27
- help
- Include support for MX27PDK platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_IMX27_VISSTRIM_M10
- bool "Vista Silicon i.MX27 Visstrim_m10"
- select IMX_HAVE_PLATFORM_GPIO_KEYS
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MX2_CAMERA
- select IMX_HAVE_PLATFORM_MX2_EMMA
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select LEDS_GPIO_REGISTER
- select SOC_IMX27
- help
- Include support for Visstrim_m10 platform and its different variants.
- This includes specific configurations for the board and its
- peripherals.
-
-config MACH_PCA100
- bool "Phytec phyCARD-s (pca100)"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_FB
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_MXC_W1
- select IMX_HAVE_PLATFORM_SPI_IMX
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX27
- help
- Include support for phyCARD-s (aka pca100) platform. This
- includes specific configurations for the module and its peripherals.
-
-config MACH_IMX27_DT
- bool "Support i.MX27 platforms from device tree"
- select SOC_IMX27
- help
- Include support for Freescale i.MX27 based platforms
- using the device tree for discovery
-
-endif
-
if ARCH_MULTI_V6
-comment "MX31 platforms:"
+comment "ARM1136 platforms"
-config MACH_MX31ADS
- bool "Support MX31ADS platforms"
- default y
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select SOC_IMX31
+config SOC_IMX31
+ bool "i.MX31 support"
+ select CPU_V6
+ select MXC_AVIC
help
- Include support for MX31ADS platform. This includes specific
- configurations for the board and its peripherals.
+ This enables support for Freescale i.MX31 processor
-config MACH_MX31ADS_WM1133_EV1
- bool "Support Wolfson Microelectronics 1133-EV1 module"
- depends on MACH_MX31ADS
- depends on MFD_WM8350_I2C
- depends on REGULATOR_WM8350 = y
+config SOC_IMX35
+ bool "i.MX35 support"
+ select MXC_AVIC
+ select PINCTRL_IMX35
help
- Include support for the Wolfson Microelectronics 1133-EV1 PMU
- and audio module for the MX31ADS platform.
-
-config MACH_MX31LILLY
- bool "Support MX31 LILLY-1131 platforms (INCO startec)"
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_SPI_IMX
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for mx31 based LILLY1131 modules. This includes
- specific configurations for the board and its peripherals.
-
-config MACH_MX31LITE
- bool "Support MX31 LITEKIT (LogicPD)"
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_MXC_RTC
- select IMX_HAVE_PLATFORM_SPI_IMX
- select LEDS_GPIO_REGISTER
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for MX31 LITEKIT platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_PCM037
- bool "Support Phytec pcm037 (i.MX31) platforms"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_MXC_W1
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for Phytec pcm037 platform. This includes
- specific configurations for the board and its peripherals.
-
-config MACH_PCM037_EET
- bool "Support pcm037 EET board extensions"
- depends on MACH_PCM037
- select IMX_HAVE_PLATFORM_GPIO_KEYS
- select IMX_HAVE_PLATFORM_SPI_IMX
- help
- Add support for PCM037 EET baseboard extensions. If you are using the
- OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel
- command-line parameter.
-
-config MACH_MX31_3DS
- bool "Support MX31PDK (3DS)"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_KEYPAD
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_SPI_IMX
- select MXC_DEBUG_BOARD
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for MX31PDK (3DS) platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_MX31_3DS_MXC_NAND_USE_BBT
- bool "Make the MXC NAND driver use the in flash Bad Block Table"
- depends on MACH_MX31_3DS
- depends on MTD_NAND_MXC
- help
- Enable this if you want that the MXC NAND driver uses the in flash
- Bad Block Table to know what blocks are bad instead of scanning the
- entire flash looking for bad block markers.
-
-config MACH_MX31MOBOARD
- bool "Support mx31moboard platforms (EPFL Mobots group)"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_SPI_IMX
- select LEDS_GPIO_REGISTER
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for mx31moboard platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_QONG
- bool "Support Dave/DENX QongEVB-LITE platform"
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_UART
- select SOC_IMX31
- help
- Include support for Dave/DENX QongEVB-LITE platform. This includes
- specific configurations for the board and its peripherals.
-
-config MACH_ARMADILLO5X0
- bool "Support Atmark Armadillo-500 Development Base Board"
- select IMX_HAVE_PLATFORM_GPIO_KEYS
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_MMC
- select IMX_HAVE_PLATFORM_MXC_NAND
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX31
- help
- Include support for Atmark Armadillo-500 platform. This includes
- specific configurations for the board and its peripherals.
-
-config MACH_KZM_ARM11_01
- bool "Support KZM-ARM11-01(Kyoto Microcomputer)"
- select IMX_HAVE_PLATFORM_IMX_UART
- select SOC_IMX31
- help
- Include support for KZM-ARM11-01. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_BUG
- bool "Support Buglabs BUGBase platform"
- default y
- select IMX_HAVE_PLATFORM_IMX_UART
- select SOC_IMX31
- help
- Include support for BUGBase 1.3 platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_IMX31_DT
- bool "Support i.MX31 platforms from device tree"
- select SOC_IMX31
- help
- Include support for Freescale i.MX31 based platforms
- using the device tree for discovery.
-
-comment "MX35 platforms:"
-
-config MACH_IMX35_DT
- bool "Support i.MX35 platforms from device tree"
- select SOC_IMX35
- help
- Include support for Freescale i.MX35 based platforms
- using the device tree for discovery.
-
-config MACH_PCM043
- bool "Support Phytec pcm043 (i.MX35) platforms"
- select IMX_HAVE_PLATFORM_FLEXCAN
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_SSI
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select USB_ULPI_VIEWPORT if USB_ULPI
- select SOC_IMX35
- help
- Include support for Phytec pcm043 platform. This includes
- specific configurations for the board and its peripherals.
-
-config MACH_MX35_3DS
- bool "Support MX35PDK platform"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_FB
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_MXC_RTC
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select MXC_DEBUG_BOARD
- select SOC_IMX35
- help
- Include support for MX35PDK platform. This includes specific
- configurations for the board and its peripherals.
-
-config MACH_VPR200
- bool "Support VPR200 platform"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_GPIO_KEYS
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_IPU_CORE
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select SOC_IMX35
- help
- Include support for VPR200 platform. This includes specific
- configurations for the board and its peripherals.
+ This enables support for Freescale i.MX31 processor
endif
-comment "Device tree only"
-
if ARCH_MULTI_V4T
config SOC_IMX1
@@ -428,12 +83,20 @@
config SOC_IMX25
bool "i.MX25 support"
- select ARCH_MXC_IOMUX_V3
select CPU_ARM926T
select MXC_AVIC
select PINCTRL_IMX25
help
This enables support for Freescale i.MX25 processor
+
+config SOC_IMX27
+ bool "i.MX27 support"
+ select CPU_ARM926T
+ select MXC_AVIC
+ select PINCTRL_IMX27
+ help
+ This enables support for Freescale i.MX27 processor
+
endif
if ARCH_MULTI_V7
@@ -541,10 +204,10 @@
endif
-comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
-
if ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
+comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
+
config SOC_IMX7D_CA7
bool
select ARM_GIC
@@ -607,6 +270,4 @@
endif
-source "arch/arm/mach-imx/devices/Kconfig"
-
endif
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index e7364e6..9cebd36 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -1,22 +1,16 @@
# SPDX-License-Identifier: GPL-2.0
obj-y := cpu.o system.o irq-common.o
-obj-$(CONFIG_SOC_IMX21) += mm-imx21.o
-
obj-$(CONFIG_SOC_IMX25) += cpu-imx25.o mach-imx25.o pm-imx25.o
-obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
-obj-$(CONFIG_SOC_IMX27) += mm-imx27.o ehci-imx27.o
+obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o mach-imx27.o
-obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o iomux-imx31.o ehci-imx31.o
-obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o ehci-imx35.o
+obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o mach-imx31.o
+obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o mach-imx35.o
imx5-pm-$(CONFIG_PM) += pm-imx5.o
obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o $(imx5-pm-y)
-obj-$(CONFIG_IMX_HAVE_IOMUX_V1) += iomux-v1.o
-obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
-
obj-$(CONFIG_MXC_TZIC) += tzic.o
obj-$(CONFIG_MXC_AVIC) += avic.o
@@ -37,37 +31,6 @@
obj-y += ssi-fiq-ksym.o
endif
-# i.MX21 based machines
-obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o
-
-# i.MX27 based machines
-obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
-obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
-obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o
-obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
-obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o
-
-# i.MX31 based machines
-obj-$(CONFIG_MACH_MX31ADS) += mach-mx31ads.o
-obj-$(CONFIG_MACH_MX31LILLY) += mach-mx31lilly.o mx31lilly-db.o
-obj-$(CONFIG_MACH_MX31LITE) += mach-mx31lite.o mx31lite-db.o
-obj-$(CONFIG_MACH_PCM037) += mach-pcm037.o
-obj-$(CONFIG_MACH_PCM037_EET) += mach-pcm037_eet.o
-obj-$(CONFIG_MACH_MX31_3DS) += mach-mx31_3ds.o
-obj-$(CONFIG_MACH_MX31MOBOARD) += mach-mx31moboard.o mx31moboard-devboard.o \
- mx31moboard-marxbot.o mx31moboard-smartbot.o
-obj-$(CONFIG_MACH_QONG) += mach-qong.o
-obj-$(CONFIG_MACH_ARMADILLO5X0) += mach-armadillo5x0.o
-obj-$(CONFIG_MACH_KZM_ARM11_01) += mach-kzm_arm11_01.o
-obj-$(CONFIG_MACH_BUG) += mach-bug.o
-obj-$(CONFIG_MACH_IMX31_DT) += imx31-dt.o
-
-# i.MX35 based machines
-obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o
-obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35_3ds.o
-obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
-obj-$(CONFIG_MACH_IMX35_DT) += imx35-dt.o
-
obj-$(CONFIG_HAVE_IMX_ANATOP) += anatop.o
obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
@@ -105,5 +68,3 @@
obj-$(CONFIG_SOC_VF610) += mach-vf610.o
obj-$(CONFIG_SOC_LS1021A) += mach-ls1021a.o
-
-obj-y += devices/
diff --git a/arch/arm/mach-imx/board-mx31lilly.h b/arch/arm/mach-imx/board-mx31lilly.h
deleted file mode 100644
index 3508c59..0000000
--- a/arch/arm/mach-imx/board-mx31lilly.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lilly_boards {
- MX31LILLY_NOBOARD = 0,
- MX31LILLY_DB = 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lilly_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LILLY_H__ */
diff --git a/arch/arm/mach-imx/board-mx31lite.h b/arch/arm/mach-imx/board-mx31lite.h
deleted file mode 100644
index 7d7c621..0000000
--- a/arch/arm/mach-imx/board-mx31lite.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lite_boards {
- MX31LITE_NOBOARD = 0,
- MX31LITE_DB = 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lite_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LITE_H__ */
diff --git a/arch/arm/mach-imx/board-mx31moboard.h b/arch/arm/mach-imx/board-mx31moboard.h
deleted file mode 100644
index 6f3ff4d..0000000
--- a/arch/arm/mach-imx/board-mx31moboard.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-#define __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31moboard_boards {
- MX31NOBOARD = 0,
- MX31DEVBOARD = 1,
- MX31MARXBOT = 2,
- MX31SMARTBOT = 3,
- MX31EYEBOT = 4,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31moboard_devboard_init(void);
-extern void mx31moboard_marxbot_init(void);
-extern void mx31moboard_smartbot_init(int board);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__ */
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 72c3fcc..2d76e2c 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -17,29 +17,14 @@ struct device_node;
enum mxc_cpu_pwr_mode;
struct of_device_id;
-void mx21_map_io(void);
-void mx27_map_io(void);
void mx31_map_io(void);
void mx35_map_io(void);
void imx21_init_early(void);
-void imx27_init_early(void);
void imx31_init_early(void);
void imx35_init_early(void);
void mxc_init_irq(void __iomem *);
-void mx21_init_irq(void);
-void mx27_init_irq(void);
void mx31_init_irq(void);
void mx35_init_irq(void);
-void imx21_soc_init(void);
-void imx27_soc_init(void);
-void imx31_soc_init(void);
-void imx35_soc_init(void);
-int mx21_clocks_init(unsigned long lref, unsigned long fref);
-int mx27_clocks_init(unsigned long fref);
-int mx31_clocks_init(unsigned long fref);
-int mx35_clocks_init(void);
-struct platform_device *mxc_register_gpio(char *name, int id,
- resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
void mxc_set_cpu_type(unsigned int type);
void mxc_restart(enum reboot_mode, const char *);
void mxc_arch_reset_init(void __iomem *);
diff --git a/arch/arm/mach-imx/cpu-imx27.c b/arch/arm/mach-imx/cpu-imx27.c
index a969aa7..bf70e13 100644
--- a/arch/arm/mach-imx/cpu-imx27.c
+++ b/arch/arm/mach-imx/cpu-imx27.c
@@ -9,6 +9,7 @@
*/
#include <linux/io.h>
+#include <linux/of_address.h>
#include <linux/module.h>
#include "hardware.h"
@@ -17,16 +18,23 @@ static int mx27_cpu_rev = -1;
static int mx27_cpu_partnumber;
#define SYS_CHIP_ID 0x00 /* The offset of CHIP ID register */
+#define SYSCTRL_OFFSET 0x800 /* Offset from CCM base address */
static int mx27_read_cpu_rev(void)
{
+ void __iomem *ccm_base;
+ struct device_node *np;
u32 val;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
+ ccm_base = of_iomap(np, 0);
+ BUG_ON(!ccm_base);
/*
* now we have access to the IO registers. As we need
* the silicon revision very early we read it here to
* avoid any further hooks
*/
- val = imx_readl(MX27_IO_ADDRESS(MX27_SYSCTRL_BASE_ADDR + SYS_CHIP_ID));
+ val = imx_readl(ccm_base + SYSCTRL_OFFSET + SYS_CHIP_ID);
mx27_cpu_partnumber = (int)((val >> 12) & 0xFFFF);
diff --git a/arch/arm/mach-imx/cpu-imx31.c b/arch/arm/mach-imx/cpu-imx31.c
index 3ee684b..b9c24b8 100644
--- a/arch/arm/mach-imx/cpu-imx31.c
+++ b/arch/arm/mach-imx/cpu-imx31.c
@@ -6,6 +6,7 @@
*/
#include <linux/module.h>
+#include <linux/of_address.h>
#include <linux/io.h>
#include "common.h"
@@ -32,10 +33,16 @@ static struct {
static int mx31_read_cpu_rev(void)
{
+ void __iomem *iim_base;
+ struct device_node *np;
u32 i, srev;
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx31-iim");
+ iim_base = of_iomap(np, 0);
+ BUG_ON(!iim_base);
+
/* read SREV register from IIM module */
- srev = imx_readl(MX31_IO_ADDRESS(MX31_IIM_BASE_ADDR + MXC_IIMSREV));
+ srev = imx_readl(iim_base + MXC_IIMSREV);
srev &= 0xff;
for (i = 0; i < ARRAY_SIZE(mx31_cpu_type); i++)
diff --git a/arch/arm/mach-imx/cpu-imx35.c b/arch/arm/mach-imx/cpu-imx35.c
index ebb3cda..80e7d8a 100644
--- a/arch/arm/mach-imx/cpu-imx35.c
+++ b/arch/arm/mach-imx/cpu-imx35.c
@@ -5,6 +5,7 @@
* Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
*/
#include <linux/module.h>
+#include <linux/of_address.h>
#include <linux/io.h>
#include "hardware.h"
@@ -14,9 +15,15 @@ static int mx35_cpu_rev = -1;
static int mx35_read_cpu_rev(void)
{
+ void __iomem *iim_base;
+ struct device_node *np;
u32 rev;
- rev = imx_readl(MX35_IO_ADDRESS(MX35_IIM_BASE_ADDR + MXC_IIMSREV));
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx35-iim");
+ iim_base = of_iomap(np, 0);
+ BUG_ON(!iim_base);
+
+ rev = imx_readl(iim_base + MXC_IIMSREV);
switch (rev) {
case 0x00:
return IMX_CHIP_REVISION_1_0;
diff --git a/arch/arm/mach-imx/devices-imx21.h b/arch/arm/mach-imx/devices-imx21.h
deleted file mode 100644
index 3679d1d..0000000
--- a/arch/arm/mach-imx/devices-imx21.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_imx21_hcd_data imx21_imx21_hcd_data;
-#define imx21_add_imx21_hcd(pdata) \
- imx_add_imx21_hcd(&imx21_imx21_hcd_data, pdata)
-
-extern const struct imx_imx2_wdt_data imx21_imx2_wdt_data;
-#define imx21_add_imx2_wdt() \
- imx_add_imx2_wdt(&imx21_imx2_wdt_data)
-
-extern const struct imx_imx_fb_data imx21_imx_fb_data;
-#define imx21_add_imx_fb(pdata) \
- imx_add_imx_fb(&imx21_imx_fb_data, pdata)
-
-extern const struct imx_imx_i2c_data imx21_imx_i2c_data;
-#define imx21_add_imx_i2c(pdata) \
- imx_add_imx_i2c(&imx21_imx_i2c_data, pdata)
-
-extern const struct imx_imx_keypad_data imx21_imx_keypad_data;
-#define imx21_add_imx_keypad(pdata) \
- imx_add_imx_keypad(&imx21_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx21_imx_ssi_data[];
-#define imx21_add_imx_ssi(id, pdata) \
- imx_add_imx_ssi(&imx21_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx21_imx_uart_data[];
-#define imx21_add_imx_uart(id, pdata) \
- imx_add_imx_uart_1irq(&imx21_imx_uart_data[id], pdata)
-#define imx21_add_imx_uart0(pdata) imx21_add_imx_uart(0, pdata)
-#define imx21_add_imx_uart1(pdata) imx21_add_imx_uart(1, pdata)
-#define imx21_add_imx_uart2(pdata) imx21_add_imx_uart(2, pdata)
-#define imx21_add_imx_uart3(pdata) imx21_add_imx_uart(3, pdata)
-
-extern const struct imx_mxc_mmc_data imx21_mxc_mmc_data[];
-#define imx21_add_mxc_mmc(id, pdata) \
- imx_add_mxc_mmc(&imx21_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx21_mxc_nand_data;
-#define imx21_add_mxc_nand(pdata) \
- imx_add_mxc_nand(&imx21_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_w1_data imx21_mxc_w1_data;
-#define imx21_add_mxc_w1() \
- imx_add_mxc_w1(&imx21_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx21_cspi_data[];
-#define imx21_add_cspi(id, pdata) \
- imx_add_spi_imx(&imx21_cspi_data[id], pdata)
-#define imx21_add_spi_imx0(pdata) imx21_add_cspi(0, pdata)
-#define imx21_add_spi_imx1(pdata) imx21_add_cspi(1, pdata)
diff --git a/arch/arm/mach-imx/devices-imx27.h b/arch/arm/mach-imx/devices-imx27.h
deleted file mode 100644
index 583a1d7..0000000
--- a/arch/arm/mach-imx/devices-imx27.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fec_data imx27_fec_data;
-#define imx27_add_fec(pdata) \
- imx_add_fec(&imx27_fec_data, pdata)
-
-extern const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data;
-#define imx27_add_fsl_usb2_udc(pdata) \
- imx_add_fsl_usb2_udc(&imx27_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_imx27_coda_data imx27_coda_data;
-#define imx27_add_coda() \
- imx_add_imx27_coda(&imx27_coda_data)
-
-extern const struct imx_imx2_wdt_data imx27_imx2_wdt_data;
-#define imx27_add_imx2_wdt() \
- imx_add_imx2_wdt(&imx27_imx2_wdt_data)
-
-extern const struct imx_imx_fb_data imx27_imx_fb_data;
-#define imx27_add_imx_fb(pdata) \
- imx_add_imx_fb(&imx27_imx_fb_data, pdata)
-
-extern const struct imx_imx_i2c_data imx27_imx_i2c_data[];
-#define imx27_add_imx_i2c(id, pdata) \
- imx_add_imx_i2c(&imx27_imx_i2c_data[id], pdata)
-
-extern const struct imx_imx_keypad_data imx27_imx_keypad_data;
-#define imx27_add_imx_keypad(pdata) \
- imx_add_imx_keypad(&imx27_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx27_imx_ssi_data[];
-#define imx27_add_imx_ssi(id, pdata) \
- imx_add_imx_ssi(&imx27_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx27_imx_uart_data[];
-#define imx27_add_imx_uart(id, pdata) \
- imx_add_imx_uart_1irq(&imx27_imx_uart_data[id], pdata)
-#define imx27_add_imx_uart0(pdata) imx27_add_imx_uart(0, pdata)
-#define imx27_add_imx_uart1(pdata) imx27_add_imx_uart(1, pdata)
-#define imx27_add_imx_uart2(pdata) imx27_add_imx_uart(2, pdata)
-#define imx27_add_imx_uart3(pdata) imx27_add_imx_uart(3, pdata)
-#define imx27_add_imx_uart4(pdata) imx27_add_imx_uart(4, pdata)
-#define imx27_add_imx_uart5(pdata) imx27_add_imx_uart(5, pdata)
-
-extern const struct imx_mx2_camera_data imx27_mx2_camera_data;
-#define imx27_add_mx2_camera(pdata) \
- imx_add_mx2_camera(&imx27_mx2_camera_data, pdata)
-
-extern const struct imx_mx2_emma_data imx27_mx2_emmaprp_data;
-#define imx27_add_mx2_emmaprp() \
- imx_add_mx2_emmaprp(&imx27_mx2_emmaprp_data)
-
-extern const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data;
-#define imx27_add_mxc_ehci_otg(pdata) \
- imx_add_mxc_ehci(&imx27_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx27_mxc_ehci_hs_data[];
-#define imx27_add_mxc_ehci_hs(id, pdata) \
- imx_add_mxc_ehci(&imx27_mxc_ehci_hs_data[id - 1], pdata)
-
-extern const struct imx_mxc_mmc_data imx27_mxc_mmc_data[];
-#define imx27_add_mxc_mmc(id, pdata) \
- imx_add_mxc_mmc(&imx27_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx27_mxc_nand_data;
-#define imx27_add_mxc_nand(pdata) \
- imx_add_mxc_nand(&imx27_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_w1_data imx27_mxc_w1_data;
-#define imx27_add_mxc_w1() \
- imx_add_mxc_w1(&imx27_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx27_cspi_data[];
-#define imx27_add_cspi(id, gtable) \
- imx_add_spi_imx(&imx27_cspi_data[id], gtable)
-#define imx27_add_spi_imx0(gtable) imx27_add_cspi(0, gtable)
-#define imx27_add_spi_imx1(gtable) imx27_add_cspi(1, gtable)
-#define imx27_add_spi_imx2(gtable) imx27_add_cspi(2, gtable)
-
-extern const struct imx_pata_imx_data imx27_pata_imx_data;
-#define imx27_add_pata_imx() \
- imx_add_pata_imx(&imx27_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices-imx31.h b/arch/arm/mach-imx/devices-imx31.h
deleted file mode 100644
index f7cc623..0000000
--- a/arch/arm/mach-imx/devices-imx31.h
+++ /dev/null
@@ -1,80 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data;
-#define imx31_add_fsl_usb2_udc(pdata) \
- imx_add_fsl_usb2_udc(&imx31_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_imx2_wdt_data imx31_imx2_wdt_data;
-#define imx31_add_imx2_wdt() \
- imx_add_imx2_wdt(&imx31_imx2_wdt_data)
-
-extern const struct imx_imx_i2c_data imx31_imx_i2c_data[];
-#define imx31_add_imx_i2c(id, pdata) \
- imx_add_imx_i2c(&imx31_imx_i2c_data[id], pdata)
-#define imx31_add_imx_i2c0(pdata) imx31_add_imx_i2c(0, pdata)
-#define imx31_add_imx_i2c1(pdata) imx31_add_imx_i2c(1, pdata)
-#define imx31_add_imx_i2c2(pdata) imx31_add_imx_i2c(2, pdata)
-
-extern const struct imx_imx_keypad_data imx31_imx_keypad_data;
-#define imx31_add_imx_keypad(pdata) \
- imx_add_imx_keypad(&imx31_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx31_imx_ssi_data[];
-#define imx31_add_imx_ssi(id, pdata) \
- imx_add_imx_ssi(&imx31_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx31_imx_uart_data[];
-#define imx31_add_imx_uart(id, pdata) \
- imx_add_imx_uart_1irq(&imx31_imx_uart_data[id], pdata)
-#define imx31_add_imx_uart0(pdata) imx31_add_imx_uart(0, pdata)
-#define imx31_add_imx_uart1(pdata) imx31_add_imx_uart(1, pdata)
-#define imx31_add_imx_uart2(pdata) imx31_add_imx_uart(2, pdata)
-#define imx31_add_imx_uart3(pdata) imx31_add_imx_uart(3, pdata)
-#define imx31_add_imx_uart4(pdata) imx31_add_imx_uart(4, pdata)
-
-extern const struct imx_ipu_core_data imx31_ipu_core_data;
-#define imx31_add_ipu_core() \
- imx_add_ipu_core(&imx31_ipu_core_data)
-#define imx31_alloc_mx3_camera(pdata) \
- imx_alloc_mx3_camera(&imx31_ipu_core_data, pdata)
-#define imx31_add_mx3_sdc_fb(pdata) \
- imx_add_mx3_sdc_fb(&imx31_ipu_core_data, pdata)
-
-extern const struct imx_mxc_ehci_data imx31_mxc_ehci_otg_data;
-#define imx31_add_mxc_ehci_otg(pdata) \
- imx_add_mxc_ehci(&imx31_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx31_mxc_ehci_hs_data[];
-#define imx31_add_mxc_ehci_hs(id, pdata) \
- imx_add_mxc_ehci(&imx31_mxc_ehci_hs_data[id - 1], pdata)
-
-extern const struct imx_mxc_mmc_data imx31_mxc_mmc_data[];
-#define imx31_add_mxc_mmc(id, pdata) \
- imx_add_mxc_mmc(&imx31_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx31_mxc_nand_data;
-#define imx31_add_mxc_nand(pdata) \
- imx_add_mxc_nand(&imx31_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_rtc_data imx31_mxc_rtc_data;
-#define imx31_add_mxc_rtc() \
- imx_add_mxc_rtc(&imx31_mxc_rtc_data)
-
-extern const struct imx_mxc_w1_data imx31_mxc_w1_data;
-#define imx31_add_mxc_w1() \
- imx_add_mxc_w1(&imx31_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx31_cspi_data[];
-#define imx31_add_cspi(id, gtable) \
- imx_add_spi_imx(&imx31_cspi_data[id], gtable)
-#define imx31_add_spi_imx0(gtable) imx31_add_cspi(0, gtable)
-#define imx31_add_spi_imx1(gtable) imx31_add_cspi(1, gtable)
-#define imx31_add_spi_imx2(gtable) imx31_add_cspi(2, gtable)
-
-extern const struct imx_pata_imx_data imx31_pata_imx_data;
-#define imx31_add_pata_imx() \
- imx_add_pata_imx(&imx31_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices-imx35.h b/arch/arm/mach-imx/devices-imx35.h
deleted file mode 100644
index 1b1bdad..0000000
--- a/arch/arm/mach-imx/devices-imx35.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fec_data imx35_fec_data;
-#define imx35_add_fec(pdata) \
- imx_add_fec(&imx35_fec_data, pdata)
-
-extern const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data;
-#define imx35_add_fsl_usb2_udc(pdata) \
- imx_add_fsl_usb2_udc(&imx35_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_flexcan_data imx35_flexcan_data[];
-#define imx35_add_flexcan(id) \
- imx_add_flexcan(&imx35_flexcan_data[id])
-#define imx35_add_flexcan0() imx35_add_flexcan(0)
-#define imx35_add_flexcan1() imx35_add_flexcan(1)
-
-extern const struct imx_imx2_wdt_data imx35_imx2_wdt_data;
-#define imx35_add_imx2_wdt() \
- imx_add_imx2_wdt(&imx35_imx2_wdt_data)
-
-extern const struct imx_imx_i2c_data imx35_imx_i2c_data[];
-#define imx35_add_imx_i2c(id, pdata) \
- imx_add_imx_i2c(&imx35_imx_i2c_data[id], pdata)
-#define imx35_add_imx_i2c0(pdata) imx35_add_imx_i2c(0, pdata)
-#define imx35_add_imx_i2c1(pdata) imx35_add_imx_i2c(1, pdata)
-#define imx35_add_imx_i2c2(pdata) imx35_add_imx_i2c(2, pdata)
-
-extern const struct imx_imx_keypad_data imx35_imx_keypad_data;
-#define imx35_add_imx_keypad(pdata) \
- imx_add_imx_keypad(&imx35_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx35_imx_ssi_data[];
-#define imx35_add_imx_ssi(id, pdata) \
- imx_add_imx_ssi(&imx35_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx35_imx_uart_data[];
-#define imx35_add_imx_uart(id, pdata) \
- imx_add_imx_uart_1irq(&imx35_imx_uart_data[id], pdata)
-#define imx35_add_imx_uart0(pdata) imx35_add_imx_uart(0, pdata)
-#define imx35_add_imx_uart1(pdata) imx35_add_imx_uart(1, pdata)
-#define imx35_add_imx_uart2(pdata) imx35_add_imx_uart(2, pdata)
-
-extern const struct imx_ipu_core_data imx35_ipu_core_data;
-#define imx35_add_ipu_core() \
- imx_add_ipu_core(&imx35_ipu_core_data)
-#define imx35_alloc_mx3_camera(pdata) \
- imx_alloc_mx3_camera(&imx35_ipu_core_data, pdata)
-#define imx35_add_mx3_sdc_fb(pdata) \
- imx_add_mx3_sdc_fb(&imx35_ipu_core_data, pdata)
-
-extern const struct imx_mxc_ehci_data imx35_mxc_ehci_otg_data;
-#define imx35_add_mxc_ehci_otg(pdata) \
- imx_add_mxc_ehci(&imx35_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx35_mxc_ehci_hs_data;
-#define imx35_add_mxc_ehci_hs(pdata) \
- imx_add_mxc_ehci(&imx35_mxc_ehci_hs_data, pdata)
-
-extern const struct imx_mxc_nand_data imx35_mxc_nand_data;
-#define imx35_add_mxc_nand(pdata) \
- imx_add_mxc_nand(&imx35_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_rtc_data imx35_mxc_rtc_data;
-#define imx35_add_mxc_rtc() \
- imx_add_mxc_rtc(&imx35_mxc_rtc_data)
-
-extern const struct imx_mxc_w1_data imx35_mxc_w1_data;
-#define imx35_add_mxc_w1() \
- imx_add_mxc_w1(&imx35_mxc_w1_data)
-
-extern const struct imx_sdhci_esdhc_imx_data imx35_sdhci_esdhc_imx_data[];
-#define imx35_add_sdhci_esdhc_imx(id, pdata) \
- imx_add_sdhci_esdhc_imx(&imx35_sdhci_esdhc_imx_data[id], pdata)
-
-extern const struct imx_spi_imx_data imx35_cspi_data[];
-#define imx35_add_cspi(id, pdata) \
- imx_add_spi_imx(&imx35_cspi_data[id], pdata)
-#define imx35_add_spi_imx0(pdata) imx35_add_cspi(0, pdata)
-#define imx35_add_spi_imx1(pdata) imx35_add_cspi(1, pdata)
-
-extern const struct imx_pata_imx_data imx35_pata_imx_data;
-#define imx35_add_pata_imx() \
- imx_add_pata_imx(&imx35_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig
deleted file mode 100644
index fdca73d..0000000
--- a/arch/arm/mach-imx/devices/Kconfig
+++ /dev/null
@@ -1,71 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-config IMX_HAVE_PLATFORM_FEC
- bool
- default y if SOC_IMX25 || SOC_IMX27 || SOC_IMX35
-
-config IMX_HAVE_PLATFORM_FLEXCAN
- bool
-
-config IMX_HAVE_PLATFORM_FSL_USB2_UDC
- bool
-
-config IMX_HAVE_PLATFORM_GPIO_KEYS
- bool
-
-config IMX_HAVE_PLATFORM_IMX21_HCD
- bool
-
-config IMX_HAVE_PLATFORM_IMX27_CODA
- bool
- default y if SOC_IMX27
-
-config IMX_HAVE_PLATFORM_IMX2_WDT
- bool
-
-config IMX_HAVE_PLATFORM_IMX_FB
- bool
-
-config IMX_HAVE_PLATFORM_IMX_I2C
- bool
-
-config IMX_HAVE_PLATFORM_IMX_KEYPAD
- bool
-
-config IMX_HAVE_PLATFORM_PATA_IMX
- bool
-
-config IMX_HAVE_PLATFORM_IMX_SSI
- bool
-
-config IMX_HAVE_PLATFORM_IMX_UART
- bool
-
-config IMX_HAVE_PLATFORM_IPU_CORE
- bool
-
-config IMX_HAVE_PLATFORM_MX2_CAMERA
- bool
-
-config IMX_HAVE_PLATFORM_MX2_EMMA
- bool
-
-config IMX_HAVE_PLATFORM_MXC_EHCI
- bool
-
-config IMX_HAVE_PLATFORM_MXC_MMC
- bool
-
-config IMX_HAVE_PLATFORM_MXC_NAND
- bool
-
-config IMX_HAVE_PLATFORM_MXC_RTC
- bool
-
-config IMX_HAVE_PLATFORM_MXC_W1
- bool
-
-config IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- bool
-
-config IMX_HAVE_PLATFORM_SPI_IMX
- bool
diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile
deleted file mode 100644
index e44758a..0000000
--- a/arch/arm/mach-imx/devices/Makefile
+++ /dev/null
@@ -1,28 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-obj-y := devices.o
-
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FEC) += platform-fec.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FLEXCAN) += platform-flexcan.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FSL_USB2_UDC) += platform-fsl-usb2-udc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_GPIO_KEYS) += platform-gpio_keys.o
-obj-y += platform-gpio-mxc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX21_HCD) += platform-imx21-hcd.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX27_CODA) += platform-imx27-coda.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT) += platform-imx2-wdt.o
-obj-y += platform-imx-dma.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_FB) += platform-imx-fb.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_I2C) += platform-imx-i2c.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_KEYPAD) += platform-imx-keypad.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_PATA_IMX) += platform-pata_imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_SSI) += platform-imx-ssi.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_UART) += platform-imx-uart.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IPU_CORE) += platform-ipu-core.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_CAMERA) += platform-mx2-camera.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_EHCI) += platform-mxc-ehci.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_MMC) += platform-mxc-mmc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_NAND) += platform-mxc_nand.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_RTC) += platform-mxc_rtc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) += platform-spi_imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_EMMA) += platform-mx2-emma.o
diff --git a/arch/arm/mach-imx/devices/devices-common.h b/arch/arm/mach-imx/devices/devices-common.h
deleted file mode 100644
index 327a1de..0000000
--- a/arch/arm/mach-imx/devices/devices-common.h
+++ /dev/null
@@ -1,293 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_data/dma-imx-sdma.h>
-
-extern struct device mxc_aips_bus;
-extern struct device mxc_ahb_bus;
-
-static inline struct platform_device *imx_add_platform_device_dmamask(
- const char *name, int id,
- const struct resource *res, unsigned int num_resources,
- const void *data, size_t size_data, u64 dmamask)
-{
- struct platform_device_info pdevinfo = {
- .name = name,
- .id = id,
- .res = res,
- .num_res = num_resources,
- .data = data,
- .size_data = size_data,
- .dma_mask = dmamask,
- };
- return platform_device_register_full(&pdevinfo);
-}
-
-static inline struct platform_device *imx_add_platform_device(
- const char *name, int id,
- const struct resource *res, unsigned int num_resources,
- const void *data, size_t size_data)
-{
- return imx_add_platform_device_dmamask(
- name, id, res, num_resources, data, size_data, 0);
-}
-
-#include <linux/fec.h>
-struct imx_fec_data {
- const char *devid;
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_fec(
- const struct imx_fec_data *data,
- const struct fec_platform_data *pdata);
-
-struct imx_flexcan_data {
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_flexcan(
- const struct imx_flexcan_data *data);
-
-#include <linux/fsl_devices.h>
-struct imx_fsl_usb2_udc_data {
- const char *devid;
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_fsl_usb2_udc(
- const struct imx_fsl_usb2_udc_data *data,
- const struct fsl_usb2_platform_data *pdata);
-
-#include <linux/gpio_keys.h>
-struct platform_device *__init imx_add_gpio_keys(
- const struct gpio_keys_platform_data *pdata);
-
-#include <linux/platform_data/usb-mx2.h>
-struct imx_imx21_hcd_data {
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx21_hcd(
- const struct imx_imx21_hcd_data *data,
- const struct mx21_usbh_platform_data *pdata);
-
-struct imx_imx27_coda_data {
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx27_coda(
- const struct imx_imx27_coda_data *data);
-
-struct imx_imx2_wdt_data {
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
-};
-struct platform_device *__init imx_add_imx2_wdt(
- const struct imx_imx2_wdt_data *data);
-
-struct imx_imxdi_rtc_data {
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imxdi_rtc(
- const struct imx_imxdi_rtc_data *data);
-
-#include <linux/platform_data/video-imxfb.h>
-struct imx_imx_fb_data {
- const char *devid;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_fb(
- const struct imx_imx_fb_data *data,
- const struct imx_fb_platform_data *pdata);
-
-#include <linux/platform_data/i2c-imx.h>
-struct imx_imx_i2c_data {
- const char *devid;
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_i2c(
- const struct imx_imx_i2c_data *data,
- const struct imxi2c_platform_data *pdata);
-
-#include <linux/input/matrix_keypad.h>
-struct imx_imx_keypad_data {
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_keypad(
- const struct imx_imx_keypad_data *data,
- const struct matrix_keymap_data *pdata);
-
-#include <linux/platform_data/asoc-imx-ssi.h>
-struct imx_imx_ssi_data {
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
- resource_size_t dmatx0;
- resource_size_t dmarx0;
- resource_size_t dmatx1;
- resource_size_t dmarx1;
-};
-struct platform_device *__init imx_add_imx_ssi(
- const struct imx_imx_ssi_data *data,
- const struct imx_ssi_platform_data *pdata);
-
-#include <linux/platform_data/serial-imx.h>
-struct imx_imx_uart_1irq_data {
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_uart_1irq(
- const struct imx_imx_uart_1irq_data *data,
- const struct imxuart_platform_data *pdata);
-
-#include <linux/platform_data/video-mx3fb.h>
-#include <linux/platform_data/media/camera-mx3.h>
-struct imx_ipu_core_data {
- resource_size_t iobase;
- resource_size_t synirq;
- resource_size_t errirq;
-};
-struct platform_device *__init imx_add_ipu_core(
- const struct imx_ipu_core_data *data);
-struct platform_device *__init imx_alloc_mx3_camera(
- const struct imx_ipu_core_data *data,
- const struct mx3_camera_pdata *pdata);
-struct platform_device *__init imx_add_mx3_sdc_fb(
- const struct imx_ipu_core_data *data,
- struct mx3fb_platform_data *pdata);
-
-#include <linux/platform_data/media/camera-mx2.h>
-struct imx_mx2_camera_data {
- const char *devid;
- resource_size_t iobasecsi;
- resource_size_t iosizecsi;
- resource_size_t irqcsi;
- resource_size_t iobaseemmaprp;
- resource_size_t iosizeemmaprp;
- resource_size_t irqemmaprp;
-};
-struct platform_device *__init imx_add_mx2_camera(
- const struct imx_mx2_camera_data *data,
- const struct mx2_camera_platform_data *pdata);
-
-
-struct imx_mx2_emma_data {
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_mx2_emmaprp(
- const struct imx_mx2_emma_data *data);
-
-#include <linux/platform_data/usb-ehci-mxc.h>
-struct imx_mxc_ehci_data {
- int id;
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_ehci(
- const struct imx_mxc_ehci_data *data,
- const struct mxc_usbh_platform_data *pdata);
-
-#include <linux/platform_data/mmc-mxcmmc.h>
-struct imx_mxc_mmc_data {
- const char *devid;
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
- resource_size_t dmareq;
-};
-struct platform_device *__init imx_add_mxc_mmc(
- const struct imx_mxc_mmc_data *data,
- const struct imxmmc_platform_data *pdata);
-
-#include <linux/platform_data/mtd-mxc_nand.h>
-struct imx_mxc_nand_data {
- const char *devid;
- /*
- * id is traditionally 0, but -1 is more appropriate. We use -1 for new
- * machines but don't change existing devices as the nand device usually
- * appears in the kernel command line to pass its partitioning.
- */
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t axibase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_nand(
- const struct imx_mxc_nand_data *data,
- const struct mxc_nand_platform_data *pdata);
-
-struct imx_pata_imx_data {
- resource_size_t iobase;
- resource_size_t iosize;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_pata_imx(
- const struct imx_pata_imx_data *data);
-
-/* mxc_rtc */
-struct imx_mxc_rtc_data {
- const char *devid;
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_rtc(
- const struct imx_mxc_rtc_data *data);
-
-/* mxc_w1 */
-struct imx_mxc_w1_data {
- resource_size_t iobase;
-};
-struct platform_device *__init imx_add_mxc_w1(
- const struct imx_mxc_w1_data *data);
-
-#include <linux/platform_data/mmc-esdhc-imx.h>
-struct imx_sdhci_esdhc_imx_data {
- const char *devid;
- int id;
- resource_size_t iobase;
- resource_size_t irq;
-};
-struct platform_device *__init imx_add_sdhci_esdhc_imx(
- const struct imx_sdhci_esdhc_imx_data *data,
- const struct esdhc_platform_data *pdata);
-
-struct imx_spi_imx_data {
- const char *devid;
- int id;
- resource_size_t iobase;
- resource_size_t iosize;
- int irq;
-};
-struct platform_device *__init imx_add_spi_imx(
- const struct imx_spi_imx_data *data, struct gpiod_lookup_table *gtable);
-
-struct platform_device *imx_add_imx_dma(char *name, resource_size_t iobase,
- int irq);
-struct platform_device *imx_add_imx_sdma(char *name,
- resource_size_t iobase, int irq, struct sdma_platform_data *pdata);
diff --git a/arch/arm/mach-imx/devices/devices.c b/arch/arm/mach-imx/devices/devices.c
deleted file mode 100644
index cd72f08..0000000
--- a/arch/arm/mach-imx/devices/devices.c
+++ /dev/null
@@ -1,35 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008 Sascha Hauer, kernel@pengutronix.de
- */
-
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/err.h>
-#include <linux/platform_device.h>
-
-#include "../common.h"
-#include "devices-common.h"
-
-struct device mxc_aips_bus = {
- .init_name = "mxc_aips",
-};
-
-struct device mxc_ahb_bus = {
- .init_name = "mxc_ahb",
-};
-
-int __init mxc_device_init(void)
-{
- int ret;
-
- ret = device_register(&mxc_aips_bus);
- if (ret < 0)
- goto done;
-
- ret = device_register(&mxc_ahb_bus);
-
-done:
- return ret;
-}
diff --git a/arch/arm/mach-imx/devices/platform-fec.c b/arch/arm/mach-imx/devices/platform-fec.c
deleted file mode 100644
index 88e853d..0000000
--- a/arch/arm/mach-imx/devices/platform-fec.c
+++ /dev/null
@@ -1,49 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_fec_data_entry_single(soc, _devid) \
- { \
- .devid = _devid, \
- .iobase = soc ## _FEC_BASE_ADDR, \
- .irq = soc ## _INT_FEC, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_fec_data imx27_fec_data __initconst =
- imx_fec_data_entry_single(MX27, "imx27-fec");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX35
-/* i.mx35 has the i.mx27 type fec */
-const struct imx_fec_data imx35_fec_data __initconst =
- imx_fec_data_entry_single(MX35, "imx27-fec");
-#endif
-
-struct platform_device *__init imx_add_fec(
- const struct imx_fec_data *data,
- const struct fec_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_add_platform_device_dmamask(data->devid, 0,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-flexcan.c b/arch/arm/mach-imx/devices/platform-flexcan.c
deleted file mode 100644
index e4eed35..0000000
--- a/arch/arm/mach-imx/devices/platform-flexcan.c
+++ /dev/null
@@ -1,45 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix, Marc Kleine-Budde <kernel@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_flexcan_data_entry_single(soc, _id, _hwid, _size) \
- { \
- .id = _id, \
- .iobase = soc ## _CAN ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_CAN ## _hwid, \
- }
-
-#define imx_flexcan_data_entry(soc, _id, _hwid, _size) \
- [_id] = imx_flexcan_data_entry_single(soc, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_flexcan_data imx35_flexcan_data[] __initconst = {
-#define imx35_flexcan_data_entry(_id, _hwid) \
- imx_flexcan_data_entry(MX35, _id, _hwid, SZ_16K)
- imx35_flexcan_data_entry(0, 1),
- imx35_flexcan_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_flexcan(
- const struct imx_flexcan_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_add_platform_device("flexcan", data->id,
- res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
deleted file mode 100644
index cc86de4..0000000
--- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
+++ /dev/null
@@ -1,51 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_fsl_usb2_udc_data_entry_single(soc, _devid) \
- { \
- .devid = _devid, \
- .iobase = soc ## _USB_OTG_BASE_ADDR, \
- .irq = soc ## _INT_USB_OTG, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst =
- imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data __initconst =
- imx_fsl_usb2_udc_data_entry_single(MX31, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data __initconst =
- imx_fsl_usb2_udc_data_entry_single(MX35, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_fsl_usb2_udc(
- const struct imx_fsl_usb2_udc_data *data,
- const struct fsl_usb2_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask(data->devid, -1,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-gpio-mxc.c b/arch/arm/mach-imx/devices/platform-gpio-mxc.c
deleted file mode 100644
index 355de84..0000000
--- a/arch/arm/mach-imx/devices/platform-gpio-mxc.c
+++ /dev/null
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2011 Linaro Limited
- */
-#include "devices-common.h"
-#include "../common.h"
-
-struct platform_device *__init mxc_register_gpio(char *name, int id,
- resource_size_t iobase, resource_size_t iosize, int irq, int irq_high)
-{
- struct resource res[] = {
- {
- .start = iobase,
- .end = iobase + iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- }, {
- .start = irq_high,
- .end = irq_high,
- .flags = IORESOURCE_IRQ,
- },
- };
- unsigned int nres;
-
- nres = irq_high ? ARRAY_SIZE(res) : ARRAY_SIZE(res) - 1;
- return platform_device_register_resndata(&mxc_aips_bus, name, id, res, nres, NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-gpio_keys.c b/arch/arm/mach-imx/devices/platform-gpio_keys.c
deleted file mode 100644
index 4886784..0000000
--- a/arch/arm/mach-imx/devices/platform-gpio_keys.c
+++ /dev/null
@@ -1,15 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-struct platform_device *__init imx_add_gpio_keys(
- const struct gpio_keys_platform_data *pdata)
-{
- return imx_add_platform_device("gpio-keys", -1, NULL,
- 0, pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-dma.c b/arch/arm/mach-imx/devices/platform-imx-dma.c
deleted file mode 100644
index 12656f2..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-dma.c
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices-common.h"
-
-struct platform_device __init __maybe_unused *imx_add_imx_dma(char *name,
- resource_size_t iobase, int irq)
-{
- struct resource res[] = {
- {
- .start = iobase,
- .end = iobase + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return platform_device_register_resndata(&mxc_ahb_bus,
- name, -1, res, ARRAY_SIZE(res), NULL, 0);
-}
-
-struct platform_device __init __maybe_unused *imx_add_imx_sdma(char *name,
- resource_size_t iobase, int irq, struct sdma_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = iobase,
- .end = iobase + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return platform_device_register_resndata(&mxc_ahb_bus, name,
- -1, res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c
deleted file mode 100644
index e553d01..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-fb.c
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_fb_data_entry_single(soc, _devid, _size) \
- { \
- .devid = _devid, \
- .iobase = soc ## _LCDC_BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_LCDC, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_fb_data imx21_imx_fb_data __initconst =
- imx_imx_fb_data_entry_single(MX21, "imx21-fb", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_fb_data imx27_imx_fb_data __initconst =
- imx_imx_fb_data_entry_single(MX27, "imx21-fb", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_imx_fb(
- const struct imx_imx_fb_data *data,
- const struct imx_fb_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask(data->devid, 0,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-i2c.c b/arch/arm/mach-imx/devices/platform-imx-i2c.c
deleted file mode 100644
index 81d317b..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-i2c.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_i2c_data_entry_single(soc, _devid, _id, _hwid, _size) \
- { \
- .devid = _devid, \
- .id = _id, \
- .iobase = soc ## _I2C ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_I2C ## _hwid, \
- }
-
-#define imx_imx_i2c_data_entry(soc, _devid, _id, _hwid, _size) \
- [_id] = imx_imx_i2c_data_entry_single(soc, _devid, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_i2c_data imx21_imx_i2c_data __initconst =
- imx_imx_i2c_data_entry_single(MX21, "imx21-i2c", 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_i2c_data imx27_imx_i2c_data[] __initconst = {
-#define imx27_imx_i2c_data_entry(_id, _hwid) \
- imx_imx_i2c_data_entry(MX27, "imx21-i2c", _id, _hwid, SZ_4K)
- imx27_imx_i2c_data_entry(0, 1),
- imx27_imx_i2c_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_i2c_data imx31_imx_i2c_data[] __initconst = {
-#define imx31_imx_i2c_data_entry(_id, _hwid) \
- imx_imx_i2c_data_entry(MX31, "imx21-i2c", _id, _hwid, SZ_4K)
- imx31_imx_i2c_data_entry(0, 1),
- imx31_imx_i2c_data_entry(1, 2),
- imx31_imx_i2c_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_i2c_data imx35_imx_i2c_data[] __initconst = {
-#define imx35_imx_i2c_data_entry(_id, _hwid) \
- imx_imx_i2c_data_entry(MX35, "imx21-i2c", _id, _hwid, SZ_4K)
- imx35_imx_i2c_data_entry(0, 1),
- imx35_imx_i2c_data_entry(1, 2),
- imx35_imx_i2c_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_i2c(
- const struct imx_imx_i2c_data *data,
- const struct imxi2c_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_add_platform_device(data->devid, data->id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-keypad.c b/arch/arm/mach-imx/devices/platform-imx-keypad.c
deleted file mode 100644
index de2e03e..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-keypad.c
+++ /dev/null
@@ -1,54 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_keypad_data_entry_single(soc, _size) \
- { \
- .iobase = soc ## _KPP_BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_KPP, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_keypad_data imx21_imx_keypad_data __initconst =
- imx_imx_keypad_data_entry_single(MX21, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_keypad_data imx27_imx_keypad_data __initconst =
- imx_imx_keypad_data_entry_single(MX27, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_keypad_data imx31_imx_keypad_data __initconst =
- imx_imx_keypad_data_entry_single(MX31, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_keypad_data imx35_imx_keypad_data __initconst =
- imx_imx_keypad_data_entry_single(MX35, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_keypad(
- const struct imx_imx_keypad_data *data,
- const struct matrix_keymap_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_add_platform_device("imx-keypad", -1,
- res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-ssi.c b/arch/arm/mach-imx/devices/platform-imx-ssi.c
deleted file mode 100644
index ed8c664..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-ssi.c
+++ /dev/null
@@ -1,86 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_ssi_data_entry(soc, _id, _hwid, _size) \
- [_id] = { \
- .id = _id, \
- .iobase = soc ## _SSI ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_SSI ## _hwid, \
- .dmatx0 = soc ## _DMA_REQ_SSI ## _hwid ## _TX0, \
- .dmarx0 = soc ## _DMA_REQ_SSI ## _hwid ## _RX0, \
- .dmatx1 = soc ## _DMA_REQ_SSI ## _hwid ## _TX1, \
- .dmarx1 = soc ## _DMA_REQ_SSI ## _hwid ## _RX1, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_ssi_data imx21_imx_ssi_data[] __initconst = {
-#define imx21_imx_ssi_data_entry(_id, _hwid) \
- imx_imx_ssi_data_entry(MX21, _id, _hwid, SZ_4K)
- imx21_imx_ssi_data_entry(0, 1),
- imx21_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_ssi_data imx27_imx_ssi_data[] __initconst = {
-#define imx27_imx_ssi_data_entry(_id, _hwid) \
- imx_imx_ssi_data_entry(MX27, _id, _hwid, SZ_4K)
- imx27_imx_ssi_data_entry(0, 1),
- imx27_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_ssi_data imx31_imx_ssi_data[] __initconst = {
-#define imx31_imx_ssi_data_entry(_id, _hwid) \
- imx_imx_ssi_data_entry(MX31, _id, _hwid, SZ_4K)
- imx31_imx_ssi_data_entry(0, 1),
- imx31_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_ssi_data imx35_imx_ssi_data[] __initconst = {
-#define imx35_imx_ssi_data_entry(_id, _hwid) \
- imx_imx_ssi_data_entry(MX35, _id, _hwid, SZ_4K)
- imx35_imx_ssi_data_entry(0, 1),
- imx35_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_ssi(
- const struct imx_imx_ssi_data *data,
- const struct imx_ssi_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
-#define DMARES(_name) { \
- .name = #_name, \
- .start = data->dma ## _name, \
- .end = data->dma ## _name, \
- .flags = IORESOURCE_DMA, \
-}
- DMARES(tx0),
- DMARES(rx0),
- DMARES(tx1),
- DMARES(rx1),
- };
-
- return imx_add_platform_device("imx-ssi", data->id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-uart.c b/arch/arm/mach-imx/devices/platform-imx-uart.c
deleted file mode 100644
index c8f01de..0000000
--- a/arch/arm/mach-imx/devices/platform-imx-uart.c
+++ /dev/null
@@ -1,92 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_uart_3irq_data_entry(soc, _id, _hwid, _size) \
- [_id] = { \
- .id = _id, \
- .iobase = soc ## _UART ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irqrx = soc ## _INT_UART ## _hwid ## RX, \
- .irqtx = soc ## _INT_UART ## _hwid ## TX, \
- .irqrts = soc ## _INT_UART ## _hwid ## RTS, \
- }
-
-#define imx_imx_uart_1irq_data_entry(soc, _id, _hwid, _size) \
- [_id] = { \
- .id = _id, \
- .iobase = soc ## _UART ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_UART ## _hwid, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_uart_1irq_data imx21_imx_uart_data[] __initconst = {
-#define imx21_imx_uart_data_entry(_id, _hwid) \
- imx_imx_uart_1irq_data_entry(MX21, _id, _hwid, SZ_4K)
- imx21_imx_uart_data_entry(0, 1),
- imx21_imx_uart_data_entry(1, 2),
- imx21_imx_uart_data_entry(2, 3),
- imx21_imx_uart_data_entry(3, 4),
-};
-#endif
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_uart_1irq_data imx27_imx_uart_data[] __initconst = {
-#define imx27_imx_uart_data_entry(_id, _hwid) \
- imx_imx_uart_1irq_data_entry(MX27, _id, _hwid, SZ_4K)
- imx27_imx_uart_data_entry(0, 1),
- imx27_imx_uart_data_entry(1, 2),
- imx27_imx_uart_data_entry(2, 3),
- imx27_imx_uart_data_entry(3, 4),
- imx27_imx_uart_data_entry(4, 5),
- imx27_imx_uart_data_entry(5, 6),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_uart_1irq_data imx31_imx_uart_data[] __initconst = {
-#define imx31_imx_uart_data_entry(_id, _hwid) \
- imx_imx_uart_1irq_data_entry(MX31, _id, _hwid, SZ_4K)
- imx31_imx_uart_data_entry(0, 1),
- imx31_imx_uart_data_entry(1, 2),
- imx31_imx_uart_data_entry(2, 3),
- imx31_imx_uart_data_entry(3, 4),
- imx31_imx_uart_data_entry(4, 5),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_uart_1irq_data imx35_imx_uart_data[] __initconst = {
-#define imx35_imx_uart_data_entry(_id, _hwid) \
- imx_imx_uart_1irq_data_entry(MX35, _id, _hwid, SZ_16K)
- imx35_imx_uart_data_entry(0, 1),
- imx35_imx_uart_data_entry(1, 2),
- imx35_imx_uart_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_uart_1irq(
- const struct imx_imx_uart_1irq_data *data,
- const struct imxuart_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- /* i.mx21 type uart runs on all i.mx except i.mx1 */
- return imx_add_platform_device("imx21-uart", data->id,
- res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx2-wdt.c b/arch/arm/mach-imx/devices/platform-imx2-wdt.c
deleted file mode 100644
index fdd355a..0000000
--- a/arch/arm/mach-imx/devices/platform-imx2-wdt.c
+++ /dev/null
@@ -1,52 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx2_wdt_data_entry_single(soc, _id, _hwid, _size) \
- { \
- .id = _id, \
- .iobase = soc ## _WDOG ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- }
-#define imx_imx2_wdt_data_entry(soc, _id, _hwid, _size) \
- [_id] = imx_imx2_wdt_data_entry_single(soc, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx2_wdt_data imx21_imx2_wdt_data __initconst =
- imx_imx2_wdt_data_entry_single(MX21, 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx2_wdt_data imx27_imx2_wdt_data __initconst =
- imx_imx2_wdt_data_entry_single(MX27, 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx2_wdt_data imx31_imx2_wdt_data __initconst =
- imx_imx2_wdt_data_entry_single(MX31, 0, , SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx2_wdt_data imx35_imx2_wdt_data __initconst =
- imx_imx2_wdt_data_entry_single(MX35, 0, , SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx2_wdt(
- const struct imx_imx2_wdt_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- },
- };
- return imx_add_platform_device("imx2-wdt", data->id,
- res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx21-hcd.c b/arch/arm/mach-imx/devices/platform-imx21-hcd.c
deleted file mode 100644
index f55763c..0000000
--- a/arch/arm/mach-imx/devices/platform-imx21-hcd.c
+++ /dev/null
@@ -1,38 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx21_hcd_data_entry_single(soc) \
- { \
- .iobase = soc ## _USBOTG_BASE_ADDR, \
- .irq = soc ## _INT_USBHOST, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx21_hcd_data imx21_imx21_hcd_data __initconst =
- imx_imx21_hcd_data_entry_single(MX21);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-struct platform_device *__init imx_add_imx21_hcd(
- const struct imx_imx21_hcd_data *data,
- const struct mx21_usbh_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_8K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask("imx21-hcd", 0,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx27-coda.c b/arch/arm/mach-imx/devices/platform-imx27-coda.c
deleted file mode 100644
index 66a116e..0000000
--- a/arch/arm/mach-imx/devices/platform-imx27-coda.c
+++ /dev/null
@@ -1,34 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Vista Silicon
- * Javier Martin <javier.martin@vista-silicon.com>
- */
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx27_coda_data imx27_coda_data __initconst = {
- .iobase = MX27_VPU_BASE_ADDR,
- .iosize = SZ_512,
- .irq = MX27_INT_VPU,
-};
-#endif
-
-struct platform_device *__init imx_add_imx27_coda(
- const struct imx_imx27_coda_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask("coda-imx27", 0, res, 2, NULL,
- 0, DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-ipu-core.c b/arch/arm/mach-imx/devices/platform-ipu-core.c
deleted file mode 100644
index b429076..0000000
--- a/arch/arm/mach-imx/devices/platform-ipu-core.c
+++ /dev/null
@@ -1,127 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_ipu_core_entry_single(soc) \
-{ \
- .iobase = soc ## _IPU_CTRL_BASE_ADDR, \
- .synirq = soc ## _INT_IPU_SYN, \
- .errirq = soc ## _INT_IPU_ERR, \
-}
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_ipu_core_data imx31_ipu_core_data __initconst =
- imx_ipu_core_entry_single(MX31);
-#endif
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_ipu_core_data imx35_ipu_core_data __initconst =
- imx_ipu_core_entry_single(MX35);
-#endif
-
-static struct platform_device *imx_ipu_coredev __initdata;
-
-struct platform_device *__init imx_add_ipu_core(
- const struct imx_ipu_core_data *data)
-{
- /* The resource order is important! */
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + 0x5f,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->iobase + 0x88,
- .end = data->iobase + 0xb3,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->synirq,
- .end = data->synirq,
- .flags = IORESOURCE_IRQ,
- }, {
- .start = data->errirq,
- .end = data->errirq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_ipu_coredev = imx_add_platform_device("ipu-core", -1,
- res, ARRAY_SIZE(res), NULL, 0);
-}
-
-struct platform_device *__init imx_alloc_mx3_camera(
- const struct imx_ipu_core_data *data,
- const struct mx3_camera_pdata *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase + 0x60,
- .end = data->iobase + 0x87,
- .flags = IORESOURCE_MEM,
- },
- };
- int ret = -ENOMEM;
- struct platform_device *pdev;
-
- if (IS_ERR_OR_NULL(imx_ipu_coredev))
- return ERR_PTR(-ENODEV);
-
- pdev = platform_device_alloc("mx3-camera", 0);
- if (!pdev)
- return ERR_PTR(-ENOMEM);
-
- pdev->dev.dma_mask = kmalloc(sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
- if (!pdev->dev.dma_mask)
- goto err;
-
- *pdev->dev.dma_mask = DMA_BIT_MASK(32);
- pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
-
- ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res));
- if (ret)
- goto err;
-
- if (pdata) {
- struct mx3_camera_pdata *copied_pdata;
-
- ret = platform_device_add_data(pdev, pdata, sizeof(*pdata));
- if (ret) {
-err:
- kfree(pdev->dev.dma_mask);
- platform_device_put(pdev);
- return ERR_PTR(-ENODEV);
- }
- copied_pdata = dev_get_platdata(&pdev->dev);
- copied_pdata->dma_dev = &imx_ipu_coredev->dev;
- }
-
- return pdev;
-}
-
-struct platform_device *__init imx_add_mx3_sdc_fb(
- const struct imx_ipu_core_data *data,
- struct mx3fb_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase + 0xb4,
- .end = data->iobase + 0x1bf,
- .flags = IORESOURCE_MEM,
- },
- };
-
- if (IS_ERR_OR_NULL(imx_ipu_coredev))
- return ERR_PTR(-ENODEV);
-
- pdata->dma_dev = &imx_ipu_coredev->dev;
-
- return imx_add_platform_device_dmamask("mx3_sdc_fb", -1,
- res, ARRAY_SIZE(res), pdata, sizeof(*pdata),
- DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mx2-camera.c b/arch/arm/mach-imx/devices/platform-mx2-camera.c
deleted file mode 100644
index 5375f8b..0000000
--- a/arch/arm/mach-imx/devices/platform-mx2-camera.c
+++ /dev/null
@@ -1,59 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mx2_camera_data_entry_single(soc, _devid) \
- { \
- .devid = _devid, \
- .iobasecsi = soc ## _CSI_BASE_ADDR, \
- .iosizecsi = SZ_4K, \
- .irqcsi = soc ## _INT_CSI, \
- }
-#define imx_mx2_camera_data_entry_single_emma(soc, _devid) \
- { \
- .devid = _devid, \
- .iobasecsi = soc ## _CSI_BASE_ADDR, \
- .iosizecsi = SZ_32, \
- .irqcsi = soc ## _INT_CSI, \
- .iobaseemmaprp = soc ## _EMMAPRP_BASE_ADDR, \
- .iosizeemmaprp = SZ_32, \
- .irqemmaprp = soc ## _INT_EMMAPRP, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mx2_camera_data imx27_mx2_camera_data __initconst =
- imx_mx2_camera_data_entry_single_emma(MX27, "imx27-camera");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_mx2_camera(
- const struct imx_mx2_camera_data *data,
- const struct mx2_camera_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobasecsi,
- .end = data->iobasecsi + data->iosizecsi - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irqcsi,
- .end = data->irqcsi,
- .flags = IORESOURCE_IRQ,
- }, {
- .start = data->iobaseemmaprp,
- .end = data->iobaseemmaprp + data->iosizeemmaprp - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irqemmaprp,
- .end = data->irqemmaprp,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask(data->devid, 0,
- res, data->iobaseemmaprp ? 4 : 2,
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
-
diff --git a/arch/arm/mach-imx/devices/platform-mx2-emma.c b/arch/arm/mach-imx/devices/platform-mx2-emma.c
deleted file mode 100644
index 20f28ba..0000000
--- a/arch/arm/mach-imx/devices/platform-mx2-emma.c
+++ /dev/null
@@ -1,37 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mx2_emmaprp_data_entry_single(soc) \
- { \
- .iobase = soc ## _EMMAPRP_BASE_ADDR, \
- .iosize = SZ_256, \
- .irq = soc ## _INT_EMMAPRP, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mx2_emma_data imx27_mx2_emmaprp_data __initconst =
- imx_mx2_emmaprp_data_entry_single(MX27);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_mx2_emmaprp(
- const struct imx_mx2_emma_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask("m2m-emmaprp", 0,
- res, 2, NULL, 0, DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc-ehci.c b/arch/arm/mach-imx/devices/platform-mxc-ehci.c
deleted file mode 100644
index d9d7cc7..0000000
--- a/arch/arm/mach-imx/devices/platform-mxc-ehci.c
+++ /dev/null
@@ -1,61 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_ehci_data_entry_single(soc, _id, hs) \
- { \
- .id = _id, \
- .iobase = soc ## _USB_ ## hs ## _BASE_ADDR, \
- .irq = soc ## _INT_USB_ ## hs, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data __initconst =
- imx_mxc_ehci_data_entry_single(MX27, 0, OTG);
-const struct imx_mxc_ehci_data imx27_mxc_ehci_hs_data[] __initconst = {
- imx_mxc_ehci_data_entry_single(MX27, 1, HS1),
- imx_mxc_ehci_data_entry_single(MX27, 2, HS2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_ehci_data imx31_mxc_ehci_otg_data __initconst =
- imx_mxc_ehci_data_entry_single(MX31, 0, OTG);
-const struct imx_mxc_ehci_data imx31_mxc_ehci_hs_data[] __initconst = {
- imx_mxc_ehci_data_entry_single(MX31, 1, HS1),
- imx_mxc_ehci_data_entry_single(MX31, 2, HS2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_ehci_data imx35_mxc_ehci_otg_data __initconst =
- imx_mxc_ehci_data_entry_single(MX35, 0, OTG);
-const struct imx_mxc_ehci_data imx35_mxc_ehci_hs_data __initconst =
- imx_mxc_ehci_data_entry_single(MX35, 1, HS);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_ehci(
- const struct imx_mxc_ehci_data *data,
- const struct mxc_usbh_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device_dmamask("mxc-ehci", data->id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc-mmc.c b/arch/arm/mach-imx/devices/platform-mxc-mmc.c
deleted file mode 100644
index cd4c502..0000000
--- a/arch/arm/mach-imx/devices/platform-mxc-mmc.c
+++ /dev/null
@@ -1,72 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_mmc_data_entry_single(soc, _devid, _id, _hwid, _size) \
- { \
- .devid = _devid, \
- .id = _id, \
- .iobase = soc ## _SDHC ## _hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_SDHC ## _hwid, \
- .dmareq = soc ## _DMA_REQ_SDHC ## _hwid, \
- }
-#define imx_mxc_mmc_data_entry(soc, _devid, _id, _hwid, _size) \
- [_id] = imx_mxc_mmc_data_entry_single(soc, _devid, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_mmc_data imx21_mxc_mmc_data[] __initconst = {
-#define imx21_mxc_mmc_data_entry(_id, _hwid) \
- imx_mxc_mmc_data_entry(MX21, "imx21-mmc", _id, _hwid, SZ_4K)
- imx21_mxc_mmc_data_entry(0, 1),
- imx21_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_mmc_data imx27_mxc_mmc_data[] __initconst = {
-#define imx27_mxc_mmc_data_entry(_id, _hwid) \
- imx_mxc_mmc_data_entry(MX27, "imx21-mmc", _id, _hwid, SZ_4K)
- imx27_mxc_mmc_data_entry(0, 1),
- imx27_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_mmc_data imx31_mxc_mmc_data[] __initconst = {
-#define imx31_mxc_mmc_data_entry(_id, _hwid) \
- imx_mxc_mmc_data_entry(MX31, "imx31-mmc", _id, _hwid, SZ_16K)
- imx31_mxc_mmc_data_entry(0, 1),
- imx31_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-struct platform_device *__init imx_add_mxc_mmc(
- const struct imx_mxc_mmc_data *data,
- const struct imxmmc_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- }, {
- .start = data->dmareq,
- .end = data->dmareq,
- .flags = IORESOURCE_DMA,
- },
- };
- return imx_add_platform_device_dmamask(data->devid, data->id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_nand.c b/arch/arm/mach-imx/devices/platform-mxc_nand.c
deleted file mode 100644
index 0f5f741..0000000
--- a/arch/arm/mach-imx/devices/platform-mxc_nand.c
+++ /dev/null
@@ -1,72 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_nand_data_entry_single(soc, _devid, _size) \
- { \
- .devid = _devid, \
- .iobase = soc ## _NFC_BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_NFC \
- }
-
-#define imx_mxc_nandv3_data_entry_single(soc, _devid, _size) \
- { \
- .devid = _devid, \
- .id = -1, \
- .iobase = soc ## _NFC_BASE_ADDR, \
- .iosize = _size, \
- .axibase = soc ## _NFC_AXI_BASE_ADDR, \
- .irq = soc ## _INT_NFC \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_nand_data imx21_mxc_nand_data __initconst =
- imx_mxc_nand_data_entry_single(MX21, "imx21-nand", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_nand_data imx27_mxc_nand_data __initconst =
- imx_mxc_nand_data_entry_single(MX27, "imx27-nand", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_nand_data imx31_mxc_nand_data __initconst =
- imx_mxc_nand_data_entry_single(MX31, "imx27-nand", SZ_4K);
-#endif
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_nand_data imx35_mxc_nand_data __initconst =
- imx_mxc_nand_data_entry_single(MX35, "imx25-nand", SZ_8K);
-#endif
-
-struct platform_device *__init imx_add_mxc_nand(
- const struct imx_mxc_nand_data *data,
- const struct mxc_nand_platform_data *pdata)
-{
- /* AXI has to come first, that's how the mxc_nand driver expect it */
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- }, {
- .start = data->axibase,
- .end = data->axibase + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- };
- return imx_add_platform_device(data->devid, data->id,
- res, ARRAY_SIZE(res) - !data->axibase,
- pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_rtc.c b/arch/arm/mach-imx/devices/platform-mxc_rtc.c
deleted file mode 100644
index 0c746de..0000000
--- a/arch/arm/mach-imx/devices/platform-mxc_rtc.c
+++ /dev/null
@@ -1,43 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010-2011 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_rtc_data_entry_single(soc, _devid) \
- { \
- .devid = _devid, \
- .iobase = soc ## _RTC_BASE_ADDR, \
- .irq = soc ## _INT_RTC, \
- }
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_rtc_data imx31_mxc_rtc_data __initconst =
- imx_mxc_rtc_data_entry_single(MX31, "imx21-rtc");
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_rtc_data imx35_mxc_rtc_data __initconst =
- imx_mxc_rtc_data_entry_single(MX35, "imx21-rtc");
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_rtc(
- const struct imx_mxc_rtc_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- return imx_add_platform_device(data->devid, -1,
- res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_w1.c b/arch/arm/mach-imx/devices/platform-mxc_w1.c
deleted file mode 100644
index ab42c6b..0000000
--- a/arch/arm/mach-imx/devices/platform-mxc_w1.c
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_w1_data_entry_single(soc) \
- { \
- .iobase = soc ## _OWIRE_BASE_ADDR, \
- }
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_w1_data imx21_mxc_w1_data __initconst =
- imx_mxc_w1_data_entry_single(MX21);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_w1_data imx27_mxc_w1_data __initconst =
- imx_mxc_w1_data_entry_single(MX27);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_w1_data imx31_mxc_w1_data __initconst =
- imx_mxc_w1_data_entry_single(MX31);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_w1_data imx35_mxc_w1_data __initconst =
- imx_mxc_w1_data_entry_single(MX35);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_w1(
- const struct imx_mxc_w1_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- };
-
- return imx_add_platform_device("mxc_w1", 0,
- res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-pata_imx.c b/arch/arm/mach-imx/devices/platform-pata_imx.c
deleted file mode 100644
index 0e985ff..0000000
--- a/arch/arm/mach-imx/devices/platform-pata_imx.c
+++ /dev/null
@@ -1,45 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_pata_imx_data_entry_single(soc, _size) \
- { \
- .iobase = soc ## _ATA_BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_ATA, \
- }
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_pata_imx_data imx27_pata_imx_data __initconst =
- imx_pata_imx_data_entry_single(MX27, SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_pata_imx_data imx31_pata_imx_data __initconst =
- imx_pata_imx_data_entry_single(MX31, SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_pata_imx_data imx35_pata_imx_data __initconst =
- imx_pata_imx_data_entry_single(MX35, SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_pata_imx(
- const struct imx_pata_imx_data *data)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- return imx_add_platform_device("pata_imx", -1,
- res, ARRAY_SIZE(res), NULL, 0);
-}
-
diff --git a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c
deleted file mode 100644
index 40c2610..0000000
--- a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c
+++ /dev/null
@@ -1,64 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix, Wolfram Sang <kernel@pengutronix.de>
- */
-
-#include <linux/platform_data/mmc-esdhc-imx.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_sdhci_esdhc_imx_data_entry_single(soc, _devid, _id, hwid) \
- { \
- .devid = _devid, \
- .id = _id, \
- .iobase = soc ## _ESDHC ## hwid ## _BASE_ADDR, \
- .irq = soc ## _INT_ESDHC ## hwid, \
- }
-
-#define imx_sdhci_esdhc_imx_data_entry(soc, devid, id, hwid) \
- [id] = imx_sdhci_esdhc_imx_data_entry_single(soc, devid, id, hwid)
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_sdhci_esdhc_imx_data
-imx35_sdhci_esdhc_imx_data[] __initconst = {
-#define imx35_sdhci_esdhc_imx_data_entry(_id, _hwid) \
- imx_sdhci_esdhc_imx_data_entry(MX35, "sdhci-esdhc-imx35", _id, _hwid)
- imx35_sdhci_esdhc_imx_data_entry(0, 1),
- imx35_sdhci_esdhc_imx_data_entry(1, 2),
- imx35_sdhci_esdhc_imx_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-static const struct esdhc_platform_data default_esdhc_pdata __initconst = {
- .wp_type = ESDHC_WP_NONE,
- .cd_type = ESDHC_CD_NONE,
-};
-
-struct platform_device *__init imx_add_sdhci_esdhc_imx(
- const struct imx_sdhci_esdhc_imx_data *data,
- const struct esdhc_platform_data *pdata)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
-
- /*
- * If machine does not provide pdata, use the default one
- * which means no WP/CD support
- */
- if (!pdata)
- pdata = &default_esdhc_pdata;
-
- return imx_add_platform_device_dmamask(data->devid, data->id, res,
- ARRAY_SIZE(res), pdata, sizeof(*pdata),
- DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-spi_imx.c b/arch/arm/mach-imx/devices/platform-spi_imx.c
deleted file mode 100644
index 27747bf..0000000
--- a/arch/arm/mach-imx/devices/platform-spi_imx.c
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/gpio/machine.h>
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_spi_imx_data_entry_single(soc, type, _devid, _id, hwid, _size) \
- { \
- .devid = _devid, \
- .id = _id, \
- .iobase = soc ## _ ## type ## hwid ## _BASE_ADDR, \
- .iosize = _size, \
- .irq = soc ## _INT_ ## type ## hwid, \
- }
-
-#define imx_spi_imx_data_entry(soc, type, devid, id, hwid, size) \
- [id] = imx_spi_imx_data_entry_single(soc, type, devid, id, hwid, size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_spi_imx_data imx21_cspi_data[] __initconst = {
-#define imx21_cspi_data_entry(_id, _hwid) \
- imx_spi_imx_data_entry(MX21, CSPI, "imx21-cspi", _id, _hwid, SZ_4K)
- imx21_cspi_data_entry(0, 1),
- imx21_cspi_data_entry(1, 2),
-};
-#endif
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_spi_imx_data imx27_cspi_data[] __initconst = {
-#define imx27_cspi_data_entry(_id, _hwid) \
- imx_spi_imx_data_entry(MX27, CSPI, "imx27-cspi", _id, _hwid, SZ_4K)
- imx27_cspi_data_entry(0, 1),
- imx27_cspi_data_entry(1, 2),
- imx27_cspi_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_spi_imx_data imx31_cspi_data[] __initconst = {
-#define imx31_cspi_data_entry(_id, _hwid) \
- imx_spi_imx_data_entry(MX31, CSPI, "imx31-cspi", _id, _hwid, SZ_4K)
- imx31_cspi_data_entry(0, 1),
- imx31_cspi_data_entry(1, 2),
- imx31_cspi_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_spi_imx_data imx35_cspi_data[] __initconst = {
-#define imx35_cspi_data_entry(_id, _hwid) \
- imx_spi_imx_data_entry(MX35, CSPI, "imx35-cspi", _id, _hwid, SZ_4K)
- imx35_cspi_data_entry(0, 1),
- imx35_cspi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_spi_imx(
- const struct imx_spi_imx_data *data, struct gpiod_lookup_table *gtable)
-{
- struct resource res[] = {
- {
- .start = data->iobase,
- .end = data->iobase + data->iosize - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = data->irq,
- .end = data->irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- if (gtable)
- gpiod_add_lookup_table(gtable);
- return imx_add_platform_device(data->devid, data->id,
- res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/ehci-imx27.c b/arch/arm/mach-imx/ehci-imx27.c
deleted file mode 100644
index 83962ce..0000000
--- a/arch/arm/mach-imx/ehci-imx27.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET 0x600
-
-#define MX27_OTG_SIC_SHIFT 29
-#define MX27_OTG_SIC_MASK (0x3 << MX27_OTG_SIC_SHIFT)
-#define MX27_OTG_PM_BIT (1 << 24)
-
-#define MX27_H2_SIC_SHIFT 21
-#define MX27_H2_SIC_MASK (0x3 << MX27_H2_SIC_SHIFT)
-#define MX27_H2_PM_BIT (1 << 16)
-#define MX27_H2_DT_BIT (1 << 5)
-
-#define MX27_H1_SIC_SHIFT 13
-#define MX27_H1_SIC_MASK (0x3 << MX27_H1_SIC_SHIFT)
-#define MX27_H1_PM_BIT (1 << 8)
-#define MX27_H1_DT_BIT (1 << 4)
-
-int mx27_initialize_usb_hw(int port, unsigned int flags)
-{
- unsigned int v;
-
- v = readl(MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- switch (port) {
- case 0: /* OTG port */
- v &= ~(MX27_OTG_SIC_MASK | MX27_OTG_PM_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_OTG_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX27_OTG_PM_BIT;
- break;
- case 1: /* H1 port */
- v &= ~(MX27_H1_SIC_MASK | MX27_H1_PM_BIT | MX27_H1_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H1_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX27_H1_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX27_H1_DT_BIT;
-
- break;
- case 2: /* H2 port */
- v &= ~(MX27_H2_SIC_MASK | MX27_H2_PM_BIT | MX27_H2_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H2_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX27_H2_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX27_H2_DT_BIT;
-
- break;
- default:
- return -EINVAL;
- }
-
- writel(v, MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- return 0;
-}
-
diff --git a/arch/arm/mach-imx/ehci-imx31.c b/arch/arm/mach-imx/ehci-imx31.c
deleted file mode 100644
index d6d794d..0000000
--- a/arch/arm/mach-imx/ehci-imx31.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET 0x600
-
-#define MX31_OTG_SIC_SHIFT 29
-#define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT)
-#define MX31_OTG_PM_BIT (1 << 24)
-
-#define MX31_H2_SIC_SHIFT 21
-#define MX31_H2_SIC_MASK (0x3 << MX31_H2_SIC_SHIFT)
-#define MX31_H2_PM_BIT (1 << 16)
-#define MX31_H2_DT_BIT (1 << 5)
-
-#define MX31_H1_SIC_SHIFT 13
-#define MX31_H1_SIC_MASK (0x3 << MX31_H1_SIC_SHIFT)
-#define MX31_H1_PM_BIT (1 << 8)
-#define MX31_H1_DT_BIT (1 << 4)
-
-int mx31_initialize_usb_hw(int port, unsigned int flags)
-{
- unsigned int v;
-
- v = readl(MX31_IO_ADDRESS(MX31_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- switch (port) {
- case 0: /* OTG port */
- v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_OTG_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_OTG_PM_BIT;
-
- break;
- case 1: /* H1 port */
- v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H1_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_H1_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX31_H1_DT_BIT;
-
- break;
- case 2: /* H2 port */
- v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H2_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_H2_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX31_H2_DT_BIT;
-
- break;
- default:
- return -EINVAL;
- }
-
- writel(v, MX31_IO_ADDRESS(MX31_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- return 0;
-}
diff --git a/arch/arm/mach-imx/ehci-imx35.c b/arch/arm/mach-imx/ehci-imx35.c
deleted file mode 100644
index e6ba965..0000000
--- a/arch/arm/mach-imx/ehci-imx35.c
+++ /dev/null
@@ -1,89 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET 0x600
-
-#define MX35_OTG_SIC_SHIFT 29
-#define MX35_OTG_SIC_MASK (0x3 << MX35_OTG_SIC_SHIFT)
-#define MX35_OTG_PM_BIT (1 << 24)
-#define MX35_OTG_PP_BIT (1 << 11)
-#define MX35_OTG_OCPOL_BIT (1 << 3)
-
-#define MX35_H1_SIC_SHIFT 21
-#define MX35_H1_SIC_MASK (0x3 << MX35_H1_SIC_SHIFT)
-#define MX35_H1_PP_BIT (1 << 18)
-#define MX35_H1_PM_BIT (1 << 16)
-#define MX35_H1_IPPUE_UP_BIT (1 << 7)
-#define MX35_H1_IPPUE_DOWN_BIT (1 << 6)
-#define MX35_H1_TLL_BIT (1 << 5)
-#define MX35_H1_USBTE_BIT (1 << 4)
-#define MX35_H1_OCPOL_BIT (1 << 2)
-
-int mx35_initialize_usb_hw(int port, unsigned int flags)
-{
- unsigned int v;
-
- v = readl(MX35_IO_ADDRESS(MX35_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- switch (port) {
- case 0: /* OTG port */
- v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT |
- MX35_OTG_OCPOL_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX35_OTG_PM_BIT;
-
- if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
- v |= MX35_OTG_PP_BIT;
-
- if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
- v |= MX35_OTG_OCPOL_BIT;
-
- break;
- case 1: /* H1 port */
- v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT |
- MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
- MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT;
-
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX35_H1_PM_BIT;
-
- if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
- v |= MX35_H1_PP_BIT;
-
- if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
- v |= MX35_H1_OCPOL_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX35_H1_TLL_BIT;
-
- if (flags & MXC_EHCI_INTERNAL_PHY)
- v |= MX35_H1_USBTE_BIT;
-
- if (flags & MXC_EHCI_IPPUE_DOWN)
- v |= MX35_H1_IPPUE_DOWN_BIT;
-
- if (flags & MXC_EHCI_IPPUE_UP)
- v |= MX35_H1_IPPUE_UP_BIT;
-
- break;
- default:
- return -EINVAL;
- }
-
- writel(v, MX35_IO_ADDRESS(MX35_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
- return 0;
-}
diff --git a/arch/arm/mach-imx/ehci.h b/arch/arm/mach-imx/ehci.h
deleted file mode 100644
index b7ad617..0000000
--- a/arch/arm/mach-imx/ehci.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __MACH_IMX_EHCI_H
-#define __MACH_IMX_EHCI_H
-
-/* values for portsc field */
-#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
-#define MXC_EHCI_FORCE_FS (1 << 24)
-#define MXC_EHCI_UTMI_8BIT (0 << 28)
-#define MXC_EHCI_UTMI_16BIT (1 << 28)
-#define MXC_EHCI_SERIAL (1 << 29)
-#define MXC_EHCI_MODE_UTMI (0 << 30)
-#define MXC_EHCI_MODE_PHILIPS (1 << 30)
-#define MXC_EHCI_MODE_ULPI (2 << 30)
-#define MXC_EHCI_MODE_SERIAL (3 << 30)
-
-/* values for flags field */
-#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
-#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
-#define MXC_EHCI_INTERFACE_MASK (0xf)
-
-#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
-#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH (1 << 6)
-#define MXC_EHCI_OC_PIN_ACTIVE_LOW (1 << 7)
-#define MXC_EHCI_TTL_ENABLED (1 << 8)
-
-#define MXC_EHCI_INTERNAL_PHY (1 << 9)
-#define MXC_EHCI_IPPUE_DOWN (1 << 10)
-#define MXC_EHCI_IPPUE_UP (1 << 11)
-#define MXC_EHCI_WAKEUP_ENABLED (1 << 12)
-#define MXC_EHCI_ITC_NO_THRESHOLD (1 << 13)
-
-#define MXC_USBCTRL_OFFSET 0
-#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
-#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
-#define MXC_USBH2CTRL_OFFSET 0x14
-
-int mx25_initialize_usb_hw(int port, unsigned int flags);
-int mx31_initialize_usb_hw(int port, unsigned int flags);
-int mx35_initialize_usb_hw(int port, unsigned int flags);
-int mx27_initialize_usb_hw(int port, unsigned int flags);
-
-#endif /* __MACH_IMX_EHCI_H */
diff --git a/arch/arm/mach-imx/hardware.h b/arch/arm/mach-imx/hardware.h
index 92c5a9c..7acf7ce 100644
--- a/arch/arm/mach-imx/hardware.h
+++ b/arch/arm/mach-imx/hardware.h
@@ -97,7 +97,6 @@
#include "mx31.h"
#include "mx35.h"
#include "mx2x.h"
-#include "mx21.h"
#include "mx27.h"
#define imx_map_entry(soc, name, _type) { \
diff --git a/arch/arm/mach-imx/imx27-dt.c b/arch/arm/mach-imx/imx27-dt.c
deleted file mode 100644
index 29d97bd..0000000
--- a/arch/arm/mach-imx/imx27-dt.c
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer, Pengutronix
- */
-
-#include <linux/irq.h>
-#include <linux/of_irq.h>
-#include <linux/of_platform.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "mx27.h"
-
-static const char * const imx27_dt_board_compat[] __initconst = {
- "fsl,imx27",
- NULL
-};
-
-DT_MACHINE_START(IMX27_DT, "Freescale i.MX27 (Device Tree Support)")
- .map_io = mx27_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_late = imx27_pm_init,
- .dt_compat = imx27_dt_board_compat,
-MACHINE_END
diff --git a/arch/arm/mach-imx/iomux-imx31.c b/arch/arm/mach-imx/iomux-imx31.c
deleted file mode 100644
index abfc306..0000000
--- a/arch/arm/mach-imx/iomux-imx31.c
+++ /dev/null
@@ -1,161 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Valentin Longchamp <valentin.longchamp@epfl.ch>
- */
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * IOMUX register (base) addresses
- */
-#define IOMUX_BASE MX31_IO_ADDRESS(MX31_IOMUXC_BASE_ADDR)
-#define IOMUXINT_OBS1 (IOMUX_BASE + 0x000)
-#define IOMUXINT_OBS2 (IOMUX_BASE + 0x004)
-#define IOMUXGPR (IOMUX_BASE + 0x008)
-#define IOMUXSW_MUX_CTL (IOMUX_BASE + 0x00C)
-#define IOMUXSW_PAD_CTL (IOMUX_BASE + 0x154)
-
-static DEFINE_SPINLOCK(gpio_mux_lock);
-
-#define IOMUX_REG_MASK (IOMUX_PADNUM_MASK & ~0x3)
-
-static DECLARE_BITMAP(mxc_pin_alloc_map, NB_PORTS * 32);
-/*
- * set the mode for a IOMUX pin.
- */
-void mxc_iomux_mode(unsigned int pin_mode)
-{
- u32 field;
- u32 l;
- u32 mode;
- void __iomem *reg;
-
- reg = IOMUXSW_MUX_CTL + (pin_mode & IOMUX_REG_MASK);
- field = pin_mode & 0x3;
- mode = (pin_mode & IOMUX_MODE_MASK) >> IOMUX_MODE_SHIFT;
-
- spin_lock(&gpio_mux_lock);
-
- l = imx_readl(reg);
- l &= ~(0xff << (field * 8));
- l |= mode << (field * 8);
- imx_writel(l, reg);
-
- spin_unlock(&gpio_mux_lock);
-}
-
-/*
- * This function configures the pad value for a IOMUX pin.
- */
-void mxc_iomux_set_pad(enum iomux_pins pin, u32 config)
-{
- u32 field, l;
- void __iomem *reg;
-
- pin &= IOMUX_PADNUM_MASK;
- reg = IOMUXSW_PAD_CTL + (pin + 2) / 3 * 4;
- field = (pin + 2) % 3;
-
- pr_debug("%s: reg offset = 0x%x, field = %d\n",
- __func__, (pin + 2) / 3, field);
-
- spin_lock(&gpio_mux_lock);
-
- l = imx_readl(reg);
- l &= ~(0x1ff << (field * 10));
- l |= config << (field * 10);
- imx_writel(l, reg);
-
- spin_unlock(&gpio_mux_lock);
-}
-
-/*
- * allocs a single pin:
- * - reserves the pin so that it is not claimed by another driver
- * - setups the iomux according to the configuration
- */
-int mxc_iomux_alloc_pin(unsigned int pin, const char *label)
-{
- unsigned pad = pin & IOMUX_PADNUM_MASK;
-
- if (pad >= (PIN_MAX + 1)) {
- printk(KERN_ERR "mxc_iomux: Attempt to request nonexistent pin %u for \"%s\"\n",
- pad, label ? label : "?");
- return -EINVAL;
- }
-
- if (test_and_set_bit(pad, mxc_pin_alloc_map)) {
- printk(KERN_ERR "mxc_iomux: pin %u already used. Allocation for \"%s\" failed\n",
- pad, label ? label : "?");
- return -EBUSY;
- }
- mxc_iomux_mode(pin);
-
- return 0;
-}
-
-int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
- const char *label)
-{
- const unsigned int *p = pin_list;
- int i;
- int ret = -EINVAL;
-
- for (i = 0; i < count; i++) {
- ret = mxc_iomux_alloc_pin(*p, label);
- if (ret)
- goto setup_error;
- p++;
- }
- return 0;
-
-setup_error:
- mxc_iomux_release_multiple_pins(pin_list, i);
- return ret;
-}
-
-void mxc_iomux_release_pin(unsigned int pin)
-{
- unsigned pad = pin & IOMUX_PADNUM_MASK;
-
- if (pad < (PIN_MAX + 1))
- clear_bit(pad, mxc_pin_alloc_map);
-}
-
-void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count)
-{
- const unsigned int *p = pin_list;
- int i;
-
- for (i = 0; i < count; i++) {
- mxc_iomux_release_pin(*p);
- p++;
- }
-}
-
-/*
- * This function enables/disables the general purpose function for a particular
- * signal.
- */
-void mxc_iomux_set_gpr(enum iomux_gp_func gp, bool en)
-{
- u32 l;
-
- spin_lock(&gpio_mux_lock);
- l = imx_readl(IOMUXGPR);
- if (en)
- l |= gp;
- else
- l &= ~gp;
-
- imx_writel(l, IOMUXGPR);
- spin_unlock(&gpio_mux_lock);
-}
diff --git a/arch/arm/mach-imx/iomux-mx21.h b/arch/arm/mach-imx/iomux-mx21.h
deleted file mode 100644
index 6eab347..0000000
--- a/arch/arm/mach-imx/iomux-mx21.h
+++ /dev/null
@@ -1,109 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX21_H__
-#define __MACH_IOMUX_MX21_H__
-
-#include "iomux-mx2x.h"
-#include "iomux-v1.h"
-
-/* Primary GPIO pin functions */
-
-#define PB22_PF_USBH1_BYP (GPIO_PORTB | GPIO_PF | 22)
-#define PB25_PF_USBH1_ON (GPIO_PORTB | GPIO_PF | 25)
-#define PC5_PF_USBOTG_SDA (GPIO_PORTC | GPIO_PF | 5)
-#define PC6_PF_USBOTG_SCL (GPIO_PORTC | GPIO_PF | 6)
-#define PC7_PF_USBOTG_ON (GPIO_PORTC | GPIO_PF | 7)
-#define PC8_PF_USBOTG_FS (GPIO_PORTC | GPIO_PF | 8)
-#define PC9_PF_USBOTG_OE (GPIO_PORTC | GPIO_PF | 9)
-#define PC10_PF_USBOTG_TXDM (GPIO_PORTC | GPIO_PF | 10)
-#define PC11_PF_USBOTG_TXDP (GPIO_PORTC | GPIO_PF | 11)
-#define PC12_PF_USBOTG_RXDM (GPIO_PORTC | GPIO_PF | 12)
-#define PC13_PF_USBOTG_RXDP (GPIO_PORTC | GPIO_PF | 13)
-#define PC16_PF_SAP_FS (GPIO_PORTC | GPIO_PF | 16)
-#define PC17_PF_SAP_RXD (GPIO_PORTC | GPIO_PF | 17)
-#define PC18_PF_SAP_TXD (GPIO_PORTC | GPIO_PF | 18)
-#define PC19_PF_SAP_CLK (GPIO_PORTC | GPIO_PF | 19)
-#define PE0_PF_TEST_WB2 (GPIO_PORTE | GPIO_PF | 0)
-#define PE1_PF_TEST_WB1 (GPIO_PORTE | GPIO_PF | 1)
-#define PE2_PF_TEST_WB0 (GPIO_PORTE | GPIO_PF | 2)
-#define PF1_PF_NFCE (GPIO_PORTF | GPIO_PF | 1)
-#define PF3_PF_NFCLE (GPIO_PORTF | GPIO_PF | 3)
-#define PF7_PF_NFIO0 (GPIO_PORTF | GPIO_PF | 7)
-#define PF8_PF_NFIO1 (GPIO_PORTF | GPIO_PF | 8)
-#define PF9_PF_NFIO2 (GPIO_PORTF | GPIO_PF | 9)
-#define PF10_PF_NFIO3 (GPIO_PORTF | GPIO_PF | 10)
-#define PF11_PF_NFIO4 (GPIO_PORTF | GPIO_PF | 11)
-#define PF12_PF_NFIO5 (GPIO_PORTF | GPIO_PF | 12)
-#define PF13_PF_NFIO6 (GPIO_PORTF | GPIO_PF | 13)
-#define PF14_PF_NFIO7 (GPIO_PORTF | GPIO_PF | 14)
-#define PF16_PF_RES (GPIO_PORTF | GPIO_PF | 16)
-
-/* Alternate GPIO pin functions */
-
-#define PA5_AF_BMI_CLK_CS (GPIO_PORTA | GPIO_AF | 5)
-#define PA6_AF_BMI_D0 (GPIO_PORTA | GPIO_AF | 6)
-#define PA7_AF_BMI_D1 (GPIO_PORTA | GPIO_AF | 7)
-#define PA8_AF_BMI_D2 (GPIO_PORTA | GPIO_AF | 8)
-#define PA9_AF_BMI_D3 (GPIO_PORTA | GPIO_AF | 9)
-#define PA10_AF_BMI_D4 (GPIO_PORTA | GPIO_AF | 10)
-#define PA11_AF_BMI_D5 (GPIO_PORTA | GPIO_AF | 11)
-#define PA12_AF_BMI_D6 (GPIO_PORTA | GPIO_AF | 12)
-#define PA13_AF_BMI_D7 (GPIO_PORTA | GPIO_AF | 13)
-#define PA14_AF_BMI_D8 (GPIO_PORTA | GPIO_AF | 14)
-#define PA15_AF_BMI_D9 (GPIO_PORTA | GPIO_AF | 15)
-#define PA16_AF_BMI_D10 (GPIO_PORTA | GPIO_AF | 16)
-#define PA17_AF_BMI_D11 (GPIO_PORTA | GPIO_AF | 17)
-#define PA18_AF_BMI_D12 (GPIO_PORTA | GPIO_AF | 18)
-#define PA19_AF_BMI_D13 (GPIO_PORTA | GPIO_AF | 19)
-#define PA20_AF_BMI_D14 (GPIO_PORTA | GPIO_AF | 20)
-#define PA21_AF_BMI_D15 (GPIO_PORTA | GPIO_AF | 21)
-#define PA22_AF_BMI_READ_REQ (GPIO_PORTA | GPIO_AF | 22)
-#define PA23_AF_BMI_WRITE (GPIO_PORTA | GPIO_AF | 23)
-#define PA29_AF_BMI_RX_FULL (GPIO_PORTA | GPIO_AF | 29)
-#define PA30_AF_BMI_READ (GPIO_PORTA | GPIO_AF | 30)
-
-/* AIN GPIO pin functions */
-
-#define PC14_AIN_SYS_CLK (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 14)
-#define PD21_AIN_USBH2_FS (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 21)
-#define PD22_AIN_USBH2_OE (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 22)
-#define PD23_AIN_USBH2_TXDM (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 23)
-#define PD24_AIN_USBH2_TXDP (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 24)
-#define PE8_AIN_IR_TXD (GPIO_PORTE | GPIO_AIN | GPIO_OUT | 8)
-#define PF0_AIN_PC_RST (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 0)
-#define PF1_AIN_PC_CE1 (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 1)
-#define PF2_AIN_PC_CE2 (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 2)
-#define PF3_AIN_PC_POE (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 3)
-#define PF4_AIN_PC_OE (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 4)
-#define PF5_AIN_PC_RW (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 5)
-
-/* BIN GPIO pin functions */
-
-#define PC14_BIN_SYS_CLK (GPIO_PORTC | GPIO_BIN | GPIO_OUT | 14)
-#define PD27_BIN_EXT_DMA_GRANT (GPIO_PORTD | GPIO_BIN | GPIO_OUT | 27)
-
-/* CIN GPIO pin functions */
-
-#define PB26_CIN_USBH1_RXDAT (GPIO_PORTB | GPIO_CIN | GPIO_OUT | 26)
-
-/* AOUT GPIO pin functions */
-
-#define PA29_AOUT_BMI_WAIT (GPIO_PORTA | GPIO_AOUT | GPIO_IN | 29)
-#define PD19_AOUT_USBH2_RXDM (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 19)
-#define PD20_AOUT_USBH2_RXDP (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 20)
-#define PD25_AOUT_EXT_DMAREQ (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 25)
-#define PD26_AOUT_USBOTG_RXDAT (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 26)
-#define PE9_AOUT_IR_RXD (GPIO_PORTE | GPIO_AOUT | GPIO_IN | 9)
-#define PF6_AOUT_PC_BVD2 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 6)
-#define PF7_AOUT_PC_BVD1 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 7)
-#define PF8_AOUT_PC_VS2 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 8)
-#define PF9_AOUT_PC_VS1 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 9)
-#define PF10_AOUT_PC_WP (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 10)
-#define PF11_AOUT_PC_READY (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 11)
-#define PF12_AOUT_PC_WAIT (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 12)
-#define PF13_AOUT_PC_CD2 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 13)
-#define PF14_AOUT_PC_CD1 (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 14)
-
-#endif /* ifndef __MACH_IOMUX_MX21_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx27.h b/arch/arm/mach-imx/iomux-mx27.h
deleted file mode 100644
index 4d848d1..0000000
--- a/arch/arm/mach-imx/iomux-mx27.h
+++ /dev/null
@@ -1,192 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX27_H__
-#define __MACH_IOMUX_MX27_H__
-
-#include "iomux-mx2x.h"
-#include "iomux-v1.h"
-
-/* Primary GPIO pin functions */
-
-#define PA0_PF_USBH2_CLK (GPIO_PORTA | GPIO_PF | 0)
-#define PA1_PF_USBH2_DIR (GPIO_PORTA | GPIO_PF | 1)
-#define PA2_PF_USBH2_DATA7 (GPIO_PORTA | GPIO_PF | 2)
-#define PA3_PF_USBH2_NXT (GPIO_PORTA | GPIO_PF | 3)
-#define PA4_PF_USBH2_STP (GPIO_PORTA | GPIO_PF | 4)
-#define PB22_PF_USBH1_SUSP (GPIO_PORTB | GPIO_PF | 22)
-#define PB25_PF_USBH1_RCV (GPIO_PORTB | GPIO_PF | 25)
-#define PC5_PF_I2C2_SDA (GPIO_PORTC | GPIO_PF | GPIO_IN | 5)
-#define PC6_PF_I2C2_SCL (GPIO_PORTC | GPIO_PF | GPIO_IN | 6)
-#define PC7_PF_USBOTG_DATA5 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 7)
-#define PC8_PF_USBOTG_DATA6 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 8)
-#define PC9_PF_USBOTG_DATA0 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 9)
-#define PC10_PF_USBOTG_DATA2 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 10)
-#define PC11_PF_USBOTG_DATA1 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 11)
-#define PC12_PF_USBOTG_DATA4 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 12)
-#define PC13_PF_USBOTG_DATA3 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 13)
-#define PC16_PF_SSI4_FS (GPIO_PORTC | GPIO_PF | GPIO_IN | 16)
-#define PC17_PF_SSI4_RXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 17)
-#define PC18_PF_SSI4_TXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 18)
-#define PC19_PF_SSI4_CLK (GPIO_PORTC | GPIO_PF | GPIO_IN | 19)
-#define PD0_PF_SD3_CMD (GPIO_PORTD | GPIO_PF | 0)
-#define PD1_PF_SD3_CLK (GPIO_PORTD | GPIO_PF | 1)
-#define PD2_PF_ATA_DATA0 (GPIO_PORTD | GPIO_PF | 2)
-#define PD3_PF_ATA_DATA1 (GPIO_PORTD | GPIO_PF | 3)
-#define PD4_PF_ATA_DATA2 (GPIO_PORTD | GPIO_PF | 4)
-#define PD5_PF_ATA_DATA3 (GPIO_PORTD | GPIO_PF | 5)
-#define PD6_PF_ATA_DATA4 (GPIO_PORTD | GPIO_PF | 6)
-#define PD7_PF_ATA_DATA5 (GPIO_PORTD | GPIO_PF | 7)
-#define PD8_PF_ATA_DATA6 (GPIO_PORTD | GPIO_PF | 8)
-#define PD9_PF_ATA_DATA7 (GPIO_PORTD | GPIO_PF | 9)
-#define PD10_PF_ATA_DATA8 (GPIO_PORTD | GPIO_PF | 10)
-#define PD11_PF_ATA_DATA9 (GPIO_PORTD | GPIO_PF | 11)
-#define PD12_PF_ATA_DATA10 (GPIO_PORTD | GPIO_PF | 12)
-#define PD13_PF_ATA_DATA11 (GPIO_PORTD | GPIO_PF | 13)
-#define PD14_PF_ATA_DATA12 (GPIO_PORTD | GPIO_PF | 14)
-#define PD15_PF_ATA_DATA13 (GPIO_PORTD | GPIO_PF | 15)
-#define PD16_PF_ATA_DATA14 (GPIO_PORTD | GPIO_PF | 16)
-#define PE0_PF_USBOTG_NXT (GPIO_PORTE | GPIO_PF | GPIO_OUT | 0)
-#define PE1_PF_USBOTG_STP (GPIO_PORTE | GPIO_PF | GPIO_OUT | 1)
-#define PE2_PF_USBOTG_DIR (GPIO_PORTE | GPIO_PF | GPIO_OUT | 2)
-#define PE24_PF_USBOTG_CLK (GPIO_PORTE | GPIO_PF | GPIO_OUT | 24)
-#define PE25_PF_USBOTG_DATA7 (GPIO_PORTE | GPIO_PF | GPIO_OUT | 25)
-#define PF1_PF_NFCLE (GPIO_PORTF | GPIO_PF | 1)
-#define PF3_PF_NFCE (GPIO_PORTF | GPIO_PF | 3)
-#define PF7_PF_PC_POE (GPIO_PORTF | GPIO_PF | 7)
-#define PF8_PF_PC_RW (GPIO_PORTF | GPIO_PF | 8)
-#define PF9_PF_PC_IOIS16 (GPIO_PORTF | GPIO_PF | 9)
-#define PF10_PF_PC_RST (GPIO_PORTF | GPIO_PF | 10)
-#define PF11_PF_PC_BVD2 (GPIO_PORTF | GPIO_PF | 11)
-#define PF12_PF_PC_BVD1 (GPIO_PORTF | GPIO_PF | 12)
-#define PF13_PF_PC_VS2 (GPIO_PORTF | GPIO_PF | 13)
-#define PF14_PF_PC_VS1 (GPIO_PORTF | GPIO_PF | 14)
-#define PF16_PF_PC_PWRON (GPIO_PORTF | GPIO_PF | 16)
-#define PF17_PF_PC_READY (GPIO_PORTF | GPIO_PF | 17)
-#define PF18_PF_PC_WAIT (GPIO_PORTF | GPIO_PF | 18)
-#define PF19_PF_PC_CD2 (GPIO_PORTF | GPIO_PF | 19)
-#define PF20_PF_PC_CD1 (GPIO_PORTF | GPIO_PF | 20)
-#define PF23_PF_ATA_DATA15 (GPIO_PORTF | GPIO_PF | 23)
-
-/* Alternate GPIO pin functions */
-
-#define PB4_AF_MSHC_DATA0 (GPIO_PORTB | GPIO_AF | GPIO_OUT | 4)
-#define PB5_AF_MSHC_DATA1 (GPIO_PORTB | GPIO_AF | GPIO_OUT | 5)
-#define PB6_AF_MSHC_DATA2 (GPIO_PORTB | GPIO_AF | GPIO_OUT | 6)
-#define PB7_AF_MSHC_DATA4 (GPIO_PORTB | GPIO_AF | GPIO_OUT | 7)
-#define PB8_AF_MSHC_BS (GPIO_PORTB | GPIO_AF | GPIO_OUT | 8)
-#define PB9_AF_MSHC_SCLK (GPIO_PORTB | GPIO_AF | GPIO_OUT | 9)
-#define PB10_AF_UART6_TXD (GPIO_PORTB | GPIO_AF | GPIO_OUT | 10)
-#define PB11_AF_UART6_RXD (GPIO_PORTB | GPIO_AF | GPIO_IN | 11)
-#define PB12_AF_UART6_CTS (GPIO_PORTB | GPIO_AF | GPIO_OUT | 12)
-#define PB13_AF_UART6_RTS (GPIO_PORTB | GPIO_AF | GPIO_IN | 13)
-#define PB18_AF_UART5_TXD (GPIO_PORTB | GPIO_AF | GPIO_OUT | 18)
-#define PB19_AF_UART5_RXD (GPIO_PORTB | GPIO_AF | GPIO_IN | 19)
-#define PB20_AF_UART5_CTS (GPIO_PORTB | GPIO_AF | GPIO_OUT | 20)
-#define PB21_AF_UART5_RTS (GPIO_PORTB | GPIO_AF | GPIO_IN | 21)
-#define PC8_AF_FEC_MDIO (GPIO_PORTC | GPIO_AF | GPIO_IN | 8)
-#define PC24_AF_GPT5_TOUT (GPIO_PORTC | GPIO_AF | 24)
-#define PC25_AF_GPT5_TIN (GPIO_PORTC | GPIO_AF | 25)
-#define PC26_AF_GPT4_TOUT (GPIO_PORTC | GPIO_AF | 26)
-#define PC27_AF_GPT4_TIN (GPIO_PORTC | GPIO_AF | 27)
-#define PD1_AF_ETMTRACE_PKT15 (GPIO_PORTD | GPIO_AF | 1)
-#define PD6_AF_ETMTRACE_PKT14 (GPIO_PORTD | GPIO_AF | 6)
-#define PD7_AF_ETMTRACE_PKT13 (GPIO_PORTD | GPIO_AF | 7)
-#define PD9_AF_ETMTRACE_PKT12 (GPIO_PORTD | GPIO_AF | 9)
-#define PD2_AF_SD3_D0 (GPIO_PORTD | GPIO_AF | 2)
-#define PD3_AF_SD3_D1 (GPIO_PORTD | GPIO_AF | 3)
-#define PD4_AF_SD3_D2 (GPIO_PORTD | GPIO_AF | 4)
-#define PD5_AF_SD3_D3 (GPIO_PORTD | GPIO_AF | 5)
-#define PD8_AF_FEC_MDIO (GPIO_PORTD | GPIO_AF | GPIO_IN | 8)
-#define PD10_AF_ETMTRACE_PKT11 (GPIO_PORTD | GPIO_AF | 10)
-#define PD11_AF_ETMTRACE_PKT10 (GPIO_PORTD | GPIO_AF | 11)
-#define PD12_AF_ETMTRACE_PKT9 (GPIO_PORTD | GPIO_AF | 12)
-#define PD13_AF_ETMTRACE_PKT8 (GPIO_PORTD | GPIO_AF | 13)
-#define PD14_AF_ETMTRACE_PKT7 (GPIO_PORTD | GPIO_AF | 14)
-#define PD15_AF_ETMTRACE_PKT6 (GPIO_PORTD | GPIO_AF | 15)
-#define PD16_AF_ETMTRACE_PKT5 (GPIO_PORTD | GPIO_AF | 16)
-#define PF1_AF_ETMTRACE_PKT0 (GPIO_PORTF | GPIO_AF | 1)
-#define PF3_AF_ETMTRACE_PKT2 (GPIO_PORTF | GPIO_AF | 3)
-#define PF5_AF_ETMPIPESTAT11 (GPIO_PORTF | GPIO_AF | 5)
-#define PF7_AF_ATA_BUFFER_EN (GPIO_PORTF | GPIO_AF | 7)
-#define PF8_AF_ATA_IORDY (GPIO_PORTF | GPIO_AF | 8)
-#define PF9_AF_ATA_INTRQ (GPIO_PORTF | GPIO_AF | 9)
-#define PF10_AF_ATA_RESET (GPIO_PORTF | GPIO_AF | 10)
-#define PF11_AF_ATA_DMACK (GPIO_PORTF | GPIO_AF | 11)
-#define PF12_AF_ATA_DMAREQ (GPIO_PORTF | GPIO_AF | 12)
-#define PF13_AF_ATA_DA0 (GPIO_PORTF | GPIO_AF | 13)
-#define PF14_AF_ATA_DA1 (GPIO_PORTF | GPIO_AF | 14)
-#define PF15_AF_ETMTRACE_SYNC (GPIO_PORTF | GPIO_AF | 15)
-#define PF16_AF_ATA_DA2 (GPIO_PORTF | GPIO_AF | 16)
-#define PF17_AF_ATA_CS0 (GPIO_PORTF | GPIO_AF | 17)
-#define PF18_AF_ATA_CS1 (GPIO_PORTF | GPIO_AF | 18)
-#define PF19_AF_ATA_DIOW (GPIO_PORTF | GPIO_AF | 19)
-#define PF20_AF_ATA_DIOR (GPIO_PORTF | GPIO_AF | 20)
-#define PF22_AF_ETMTRACE_CLK (GPIO_PORTF | GPIO_AF | 22)
-#define PF23_AF_ETMTRACE_PKT4 (GPIO_PORTF | GPIO_AF | 23)
-
-/* AIN GPIO pin functions */
-
-#define PC14_AIN_SSI1_MCLK (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 14)
-#define PC15_AIN_GPT6_TOUT (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 15)
-#define PD0_AIN_FEC_TXD0 (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 0)
-#define PD1_AIN_FEC_TXD1 (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 1)
-#define PD2_AIN_FEC_TXD2 (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 2)
-#define PD3_AIN_FEC_TXD3 (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 3)
-#define PD9_AIN_FEC_MDC (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 9)
-#define PD16_AIN_FEC_TX_ER (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 16)
-#define PD27_AIN_EXT_DMA_GRANT (GPIO_PORTD | GPIO_AIN | GPIO_OUT | 27)
-#define PF23_AIN_FEC_TX_EN (GPIO_PORTF | GPIO_AIN | GPIO_OUT | 23)
-
-/* BIN GPIO pin functions */
-
-#define PC14_BIN_SSI2_MCLK (GPIO_PORTC | GPIO_BIN | GPIO_OUT | 14)
-
-/* CIN GPIO pin functions */
-
-#define PD2_CIN_SLCDC1_DAT0 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 2)
-#define PD3_CIN_SLCDC1_DAT1 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 3)
-#define PD4_CIN_SLCDC1_DAT2 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 4)
-#define PD5_CIN_SLCDC1_DAT3 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 5)
-#define PD6_CIN_SLCDC1_DAT4 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 6)
-#define PD7_CIN_SLCDC1_DAT5 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 7)
-#define PD8_CIN_SLCDC1_DAT6 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 8)
-#define PD9_CIN_SLCDC1_DAT7 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 9)
-#define PD10_CIN_SLCDC1_DAT8 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 10)
-#define PD11_CIN_SLCDC1_DAT9 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 11)
-#define PD12_CIN_SLCDC1_DAT10 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 12)
-#define PD13_CIN_SLCDC1_DAT11 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 13)
-#define PD14_CIN_SLCDC1_DAT12 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 14)
-#define PD15_CIN_SLCDC1_DAT13 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 15)
-#define PD16_CIN_SLCDC1_DAT14 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 16)
-#define PD23_CIN_SLCDC1_DAT15 (GPIO_PORTD | GPIO_CIN | GPIO_OUT | 23)
-#define PF27_CIN_EXT_DMA_GRANT (GPIO_PORTF | GPIO_CIN | GPIO_OUT | 27)
-/* LCDC_TESTx on PBxx omitted, because it's not clear what they do */
-
-/* AOUT GPIO pin functions */
-
-#define PC14_AOUT_GPT6_TIN (GPIO_PORTC | GPIO_AOUT | GPIO_IN | 14)
-#define PD4_AOUT_FEC_RX_ER (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 4)
-#define PD5_AOUT_FEC_RXD1 (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 5)
-#define PD6_AOUT_FEC_RXD2 (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 6)
-#define PD7_AOUT_FEC_RXD3 (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 7)
-#define PD10_AOUT_FEC_CRS (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 10)
-#define PD11_AOUT_FEC_TX_CLK (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 11)
-#define PD12_AOUT_FEC_RXD0 (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 12)
-#define PD13_AOUT_FEC_RX_DV (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 13)
-#define PD14_AOUT_FEC_RX_CLK (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 14)
-#define PD15_AOUT_FEC_COL (GPIO_PORTD | GPIO_AOUT | GPIO_IN | 15)
-
-/* BOUT GPIO pin functions */
-
-#define PC17_BOUT_PC_IOIS16 (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 17)
-#define PC18_BOUT_PC_BVD2 (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 18)
-#define PC19_BOUT_PC_BVD1 (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 19)
-#define PC28_BOUT_PC_BVD2 (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 28)
-#define PC29_BOUT_PC_VS1 (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 29)
-#define PC30_BOUT_PC_READY (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 30)
-#define PC31_BOUT_PC_WAIT (GPIO_PORTC | GPIO_BOUT | GPIO_IN | 31)
-
-#endif /* __MACH_IOMUX_MX27_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx2x.h b/arch/arm/mach-imx/iomux-mx2x.h
deleted file mode 100644
index ce6b6d2..0000000
--- a/arch/arm/mach-imx/iomux-mx2x.h
+++ /dev/null
@@ -1,217 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX2x_H__
-#define __MACH_IOMUX_MX2x_H__
-
-/* Primary GPIO pin functions */
-
-#define PA5_PF_LSCLK (GPIO_PORTA | GPIO_PF | GPIO_OUT | 5)
-#define PA6_PF_LD0 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 6)
-#define PA7_PF_LD1 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 7)
-#define PA8_PF_LD2 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 8)
-#define PA9_PF_LD3 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 9)
-#define PA10_PF_LD4 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 10)
-#define PA11_PF_LD5 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 11)
-#define PA12_PF_LD6 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 12)
-#define PA13_PF_LD7 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 13)
-#define PA14_PF_LD8 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 14)
-#define PA15_PF_LD9 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 15)
-#define PA16_PF_LD10 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 16)
-#define PA17_PF_LD11 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 17)
-#define PA18_PF_LD12 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 18)
-#define PA19_PF_LD13 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 19)
-#define PA20_PF_LD14 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 20)
-#define PA21_PF_LD15 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 21)
-#define PA22_PF_LD16 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 22)
-#define PA23_PF_LD17 (GPIO_PORTA | GPIO_PF | GPIO_OUT | 23)
-#define PA24_PF_REV (GPIO_PORTA | GPIO_PF | GPIO_OUT | 24)
-#define PA25_PF_CLS (GPIO_PORTA | GPIO_PF | GPIO_OUT | 25)
-#define PA26_PF_PS (GPIO_PORTA | GPIO_PF | GPIO_OUT | 26)
-#define PA27_PF_SPL_SPR (GPIO_PORTA | GPIO_PF | GPIO_OUT | 27)
-#define PA28_PF_HSYNC (GPIO_PORTA | GPIO_PF | GPIO_OUT | 28)
-#define PA29_PF_VSYNC (GPIO_PORTA | GPIO_PF | GPIO_OUT | 29)
-#define PA30_PF_CONTRAST (GPIO_PORTA | GPIO_PF | GPIO_OUT | 30)
-#define PA31_PF_OE_ACD (GPIO_PORTA | GPIO_PF | GPIO_OUT | 31)
-#define PB4_PF_SD2_D0 (GPIO_PORTB | GPIO_PF | 4)
-#define PB5_PF_SD2_D1 (GPIO_PORTB | GPIO_PF | 5)
-#define PB6_PF_SD2_D2 (GPIO_PORTB | GPIO_PF | 6)
-#define PB7_PF_SD2_D3 (GPIO_PORTB | GPIO_PF | 7)
-#define PB8_PF_SD2_CMD (GPIO_PORTB | GPIO_PF | 8)
-#define PB9_PF_SD2_CLK (GPIO_PORTB | GPIO_PF | 9)
-#define PB10_PF_CSI_D0 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 10)
-#define PB11_PF_CSI_D1 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 11)
-#define PB12_PF_CSI_D2 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 12)
-#define PB13_PF_CSI_D3 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 13)
-#define PB14_PF_CSI_D4 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 14)
-#define PB15_PF_CSI_MCLK (GPIO_PORTB | GPIO_PF | GPIO_OUT | 15)
-#define PB16_PF_CSI_PIXCLK (GPIO_PORTB | GPIO_PF | GPIO_OUT | 16)
-#define PB17_PF_CSI_D5 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 17)
-#define PB18_PF_CSI_D6 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 18)
-#define PB19_PF_CSI_D7 (GPIO_PORTB | GPIO_PF | GPIO_OUT | 19)
-#define PB20_PF_CSI_VSYNC (GPIO_PORTB | GPIO_PF | GPIO_OUT | 20)
-#define PB21_PF_CSI_HSYNC (GPIO_PORTB | GPIO_PF | GPIO_OUT | 21)
-#define PB23_PF_USB_PWR (GPIO_PORTB | GPIO_PF | 23)
-#define PB24_PF_USB_OC (GPIO_PORTB | GPIO_PF | 24)
-#define PB26_PF_USBH1_FS (GPIO_PORTB | GPIO_PF | 26)
-#define PB27_PF_USBH1_OE (GPIO_PORTB | GPIO_PF | 27)
-#define PB28_PF_USBH1_TXDM (GPIO_PORTB | GPIO_PF | 28)
-#define PB29_PF_USBH1_TXDP (GPIO_PORTB | GPIO_PF | 29)
-#define PB30_PF_USBH1_RXDM (GPIO_PORTB | GPIO_PF | 30)
-#define PB31_PF_USBH1_RXDP (GPIO_PORTB | GPIO_PF | 31)
-#define PC14_PF_TOUT (GPIO_PORTC | GPIO_PF | 14)
-#define PC15_PF_TIN (GPIO_PORTC | GPIO_PF | 15)
-#define PC20_PF_SSI1_FS (GPIO_PORTC | GPIO_PF | GPIO_IN | 20)
-#define PC21_PF_SSI1_RXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 21)
-#define PC22_PF_SSI1_TXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 22)
-#define PC23_PF_SSI1_CLK (GPIO_PORTC | GPIO_PF | GPIO_IN | 23)
-#define PC24_PF_SSI2_FS (GPIO_PORTC | GPIO_PF | GPIO_IN | 24)
-#define PC25_PF_SSI2_RXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 25)
-#define PC26_PF_SSI2_TXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 26)
-#define PC27_PF_SSI2_CLK (GPIO_PORTC | GPIO_PF | GPIO_IN | 27)
-#define PC28_PF_SSI3_FS (GPIO_PORTC | GPIO_PF | GPIO_IN | 28)
-#define PC29_PF_SSI3_RXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 29)
-#define PC30_PF_SSI3_TXD (GPIO_PORTC | GPIO_PF | GPIO_IN | 30)
-#define PC31_PF_SSI3_CLK (GPIO_PORTC | GPIO_PF | GPIO_IN | 31)
-#define PD17_PF_I2C_DATA (GPIO_PORTD | GPIO_PF | GPIO_OUT | 17)
-#define PD18_PF_I2C_CLK (GPIO_PORTD | GPIO_PF | GPIO_OUT | 18)
-#define PD19_PF_CSPI2_SS2 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 19)
-#define PD20_PF_CSPI2_SS1 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 20)
-#define PD21_PF_CSPI2_SS0 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 21)
-#define PD22_PF_CSPI2_SCLK (GPIO_PORTD | GPIO_PF | GPIO_OUT | 22)
-#define PD23_PF_CSPI2_MISO (GPIO_PORTD | GPIO_PF | GPIO_IN | 23)
-#define PD24_PF_CSPI2_MOSI (GPIO_PORTD | GPIO_PF | GPIO_OUT | 24)
-#define PD25_PF_CSPI1_RDY (GPIO_PORTD | GPIO_PF | GPIO_OUT | 25)
-#define PD26_PF_CSPI1_SS2 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 26)
-#define PD27_PF_CSPI1_SS1 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 27)
-#define PD28_PF_CSPI1_SS0 (GPIO_PORTD | GPIO_PF | GPIO_OUT | 28)
-#define PD29_PF_CSPI1_SCLK (GPIO_PORTD | GPIO_PF | GPIO_OUT | 29)
-#define PD30_PF_CSPI1_MISO (GPIO_PORTD | GPIO_PF | GPIO_IN | 30)
-#define PD31_PF_CSPI1_MOSI (GPIO_PORTD | GPIO_PF | GPIO_OUT | 31)
-#define PE3_PF_UART2_CTS (GPIO_PORTE | GPIO_PF | GPIO_OUT | 3)
-#define PE4_PF_UART2_RTS (GPIO_PORTE | GPIO_PF | GPIO_IN | 4)
-#define PE5_PF_PWMO (GPIO_PORTE | GPIO_PF | 5)
-#define PE6_PF_UART2_TXD (GPIO_PORTE | GPIO_PF | GPIO_OUT | 6)
-#define PE7_PF_UART2_RXD (GPIO_PORTE | GPIO_PF | GPIO_IN | 7)
-#define PE8_PF_UART3_TXD (GPIO_PORTE | GPIO_PF | GPIO_OUT | 8)
-#define PE9_PF_UART3_RXD (GPIO_PORTE | GPIO_PF | GPIO_IN | 9)
-#define PE10_PF_UART3_CTS (GPIO_PORTE | GPIO_PF | GPIO_OUT | 10)
-#define PE11_PF_UART3_RTS (GPIO_PORTE | GPIO_PF | GPIO_IN | 11)
-#define PE12_PF_UART1_TXD (GPIO_PORTE | GPIO_PF | GPIO_OUT | 12)
-#define PE13_PF_UART1_RXD (GPIO_PORTE | GPIO_PF | GPIO_IN | 13)
-#define PE14_PF_UART1_CTS (GPIO_PORTE | GPIO_PF | GPIO_OUT | 14)
-#define PE15_PF_UART1_RTS (GPIO_PORTE | GPIO_PF | GPIO_IN | 15)
-#define PE16_PF_RTCK (GPIO_PORTE | GPIO_PF | GPIO_OUT | 16)
-#define PE17_PF_RESET_OUT (GPIO_PORTE | GPIO_PF | 17)
-#define PE18_PF_SD1_D0 (GPIO_PORTE | GPIO_PF | 18)
-#define PE19_PF_SD1_D1 (GPIO_PORTE | GPIO_PF | 19)
-#define PE20_PF_SD1_D2 (GPIO_PORTE | GPIO_PF | 20)
-#define PE21_PF_SD1_D3 (GPIO_PORTE | GPIO_PF | 21)
-#define PE22_PF_SD1_CMD (GPIO_PORTE | GPIO_PF | 22)
-#define PE23_PF_SD1_CLK (GPIO_PORTE | GPIO_PF | 23)
-#define PF0_PF_NRFB (GPIO_PORTF | GPIO_PF | 0)
-#define PF2_PF_NFWP (GPIO_PORTF | GPIO_PF | 2)
-#define PF4_PF_NFALE (GPIO_PORTF | GPIO_PF | 4)
-#define PF5_PF_NFRE (GPIO_PORTF | GPIO_PF | 5)
-#define PF6_PF_NFWE (GPIO_PORTF | GPIO_PF | 6)
-#define PF15_PF_CLKO (GPIO_PORTF | GPIO_PF | 15)
-#define PF21_PF_CS4 (GPIO_PORTF | GPIO_PF | 21)
-#define PF22_PF_CS5 (GPIO_PORTF | GPIO_PF | 22)
-
-/* Alternate GPIO pin functions */
-
-#define PB26_AF_UART4_RTS (GPIO_PORTB | GPIO_AF | GPIO_IN | 26)
-#define PB28_AF_UART4_TXD (GPIO_PORTB | GPIO_AF | GPIO_OUT | 28)
-#define PB29_AF_UART4_CTS (GPIO_PORTB | GPIO_AF | GPIO_OUT | 29)
-#define PB31_AF_UART4_RXD (GPIO_PORTB | GPIO_AF | GPIO_IN | 31)
-#define PC28_AF_SLCDC2_D0 (GPIO_PORTC | GPIO_AF | 28)
-#define PC29_AF_SLCDC2_RS (GPIO_PORTC | GPIO_AF | 29)
-#define PC30_AF_SLCDC2_CS (GPIO_PORTC | GPIO_AF | 30)
-#define PC31_AF_SLCDC2_CLK (GPIO_PORTC | GPIO_AF | 31)
-#define PD19_AF_USBH2_DATA4 (GPIO_PORTD | GPIO_AF | 19)
-#define PD20_AF_USBH2_DATA3 (GPIO_PORTD | GPIO_AF | 20)
-#define PD21_AF_USBH2_DATA6 (GPIO_PORTD | GPIO_AF | 21)
-#define PD22_AF_USBH2_DATA0 (GPIO_PORTD | GPIO_AF | 22)
-#define PD23_AF_USBH2_DATA2 (GPIO_PORTD | GPIO_AF | 23)
-#define PD24_AF_USBH2_DATA1 (GPIO_PORTD | GPIO_AF | 24)
-#define PD26_AF_USBH2_DATA5 (GPIO_PORTD | GPIO_AF | 26)
-#define PE0_AF_KP_COL6 (GPIO_PORTE | GPIO_AF | 0)
-#define PE1_AF_KP_ROW6 (GPIO_PORTE | GPIO_AF | 1)
-#define PE2_AF_KP_ROW7 (GPIO_PORTE | GPIO_AF | 2)
-#define PE3_AF_KP_COL7 (GPIO_PORTE | GPIO_AF | 3)
-#define PE4_AF_KP_ROW7 (GPIO_PORTE | GPIO_AF | 4)
-#define PE6_AF_KP_COL6 (GPIO_PORTE | GPIO_AF | 6)
-#define PE7_AF_KP_ROW6 (GPIO_PORTE | GPIO_AF | 7)
-#define PE16_AF_OWIRE (GPIO_PORTE | GPIO_AF | 16)
-#define PE18_AF_CSPI3_MISO (GPIO_PORTE | GPIO_AF | GPIO_IN | 18)
-#define PE21_AF_CSPI3_SS (GPIO_PORTE | GPIO_AF | GPIO_OUT | 21)
-#define PE22_AF_CSPI3_MOSI (GPIO_PORTE | GPIO_AF | GPIO_OUT | 22)
-#define PE23_AF_CSPI3_SCLK (GPIO_PORTE | GPIO_AF | GPIO_OUT | 23)
-
-/* AIN GPIO pin functions */
-
-#define PA6_AIN_SLCDC1_DAT0 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 6)
-#define PA7_AIN_SLCDC1_DAT1 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 7)
-#define PA8_AIN_SLCDC1_DAT2 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 8)
-#define PA0_AIN_SLCDC1_DAT3 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 0)
-#define PA11_AIN_SLCDC1_DAT5 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 11)
-#define PA13_AIN_SLCDC1_DAT7 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 13)
-#define PA15_AIN_SLCDC1_DAT9 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 15)
-#define PA17_AIN_SLCDC1_DAT11 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 17)
-#define PA19_AIN_SLCDC1_DAT13 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 19)
-#define PA21_AIN_SLCDC1_DAT15 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 21)
-#define PA22_AIN_EXT_DMAGRANT (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 22)
-#define PA24_AIN_SLCDC1_D0 (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 24)
-#define PA25_AIN_SLCDC1_RS (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 25)
-#define PA26_AIN_SLCDC1_CS (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 26)
-#define PA27_AIN_SLCDC1_CLK (GPIO_PORTA | GPIO_AIN | GPIO_OUT | 27)
-#define PB6_AIN_SLCDC1_D0 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 6)
-#define PB7_AIN_SLCDC1_RS (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 7)
-#define PB8_AIN_SLCDC1_CS (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 8)
-#define PB9_AIN_SLCDC1_CLK (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 9)
-#define PB25_AIN_SLCDC1_DAT0 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 25)
-#define PB26_AIN_SLCDC1_DAT1 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 26)
-#define PB27_AIN_SLCDC1_DAT2 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 27)
-#define PB28_AIN_SLCDC1_DAT3 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 28)
-#define PB29_AIN_SLCDC1_DAT4 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 29)
-#define PB30_AIN_SLCDC1_DAT5 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 30)
-#define PB31_AIN_SLCDC1_DAT6 (GPIO_PORTB | GPIO_AIN | GPIO_OUT | 31)
-#define PC5_AIN_SLCDC1_DAT7 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 5)
-#define PC6_AIN_SLCDC1_DAT8 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 6)
-#define PC7_AIN_SLCDC1_DAT9 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 7)
-#define PC8_AIN_SLCDC1_DAT10 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 8)
-#define PC9_AIN_SLCDC1_DAT11 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 9)
-#define PC10_AIN_SLCDC1_DAT12 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 10)
-#define PC11_AIN_SLCDC1_DAT13 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 11)
-#define PC12_AIN_SLCDC1_DAT14 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 12)
-#define PC13_AIN_SLCDC1_DAT15 (GPIO_PORTC | GPIO_AIN | GPIO_OUT | 13)
-#define PE5_AIN_PC_SPKOUT (GPIO_PORTE | GPIO_AIN | GPIO_OUT | 5)
-
-/* BIN GPIO pin functions */
-
-#define PE5_BIN_TOUT2 (GPIO_PORTE | GPIO_BIN | GPIO_OUT | 5)
-
-/* CIN GPIO pin functions */
-
-#define PA14_CIN_SLCDC1_DAT0 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 14)
-#define PA15_CIN_SLCDC1_DAT1 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 15)
-#define PA16_CIN_SLCDC1_DAT2 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 16)
-#define PA17_CIN_SLCDC1_DAT3 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 17)
-#define PA18_CIN_SLCDC1_DAT4 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 18)
-#define PA19_CIN_SLCDC1_DAT5 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 19)
-#define PA20_CIN_SLCDC1_DAT6 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 20)
-#define PA21_CIN_SLCDC1_DAT7 (GPIO_PORTA | GPIO_CIN | GPIO_OUT | 21)
-#define PB30_CIN_UART4_CTS (GPIO_PORTB | GPIO_CIN | GPIO_OUT | 30)
-#define PE5_CIN_TOUT3 (GPIO_PORTE | GPIO_CIN | GPIO_OUT | 5)
-
-/* AOUT GPIO pin functions */
-
-#define PB29_AOUT_UART4_RXD (GPIO_PORTB | GPIO_AOUT | GPIO_IN | 29)
-#define PB31_AOUT_UART4_RTS (GPIO_PORTB | GPIO_AOUT | GPIO_IN | 31)
-#define PC8_AOUT_USBOTG_TXR_INT (GPIO_PORTC | GPIO_AOUT | GPIO_IN | 8)
-#define PC15_AOUT_WKGD (GPIO_PORTC | GPIO_AOUT | GPIO_IN | 15)
-#define PF21_AOUT_DTACK (GPIO_PORTF | GPIO_AOUT | GPIO_IN | 21)
-
-#endif /* ifndef __MACH_IOMUX_MX2x_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx3.h b/arch/arm/mach-imx/iomux-mx3.h
deleted file mode 100644
index 99270a1..0000000
--- a/arch/arm/mach-imx/iomux-mx3.h
+++ /dev/null
@@ -1,706 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- */
-#ifndef __MACH_IOMUX_MX3_H__
-#define __MACH_IOMUX_MX3_H__
-
-#include <linux/types.h>
-/*
- * various IOMUX output functions
- */
-
-#define IOMUX_OCONFIG_GPIO (0 << 4) /* used as GPIO */
-#define IOMUX_OCONFIG_FUNC (1 << 4) /* used as function */
-#define IOMUX_OCONFIG_ALT1 (2 << 4) /* used as alternate function 1 */
-#define IOMUX_OCONFIG_ALT2 (3 << 4) /* used as alternate function 2 */
-#define IOMUX_OCONFIG_ALT3 (4 << 4) /* used as alternate function 3 */
-#define IOMUX_OCONFIG_ALT4 (5 << 4) /* used as alternate function 4 */
-#define IOMUX_OCONFIG_ALT5 (6 << 4) /* used as alternate function 5 */
-#define IOMUX_OCONFIG_ALT6 (7 << 4) /* used as alternate function 6 */
-#define IOMUX_ICONFIG_NONE 0 /* not configured for input */
-#define IOMUX_ICONFIG_GPIO 1 /* used as GPIO */
-#define IOMUX_ICONFIG_FUNC 2 /* used as function */
-#define IOMUX_ICONFIG_ALT1 4 /* used as alternate function 1 */
-#define IOMUX_ICONFIG_ALT2 8 /* used as alternate function 2 */
-
-#define IOMUX_CONFIG_GPIO (IOMUX_OCONFIG_GPIO | IOMUX_ICONFIG_GPIO)
-#define IOMUX_CONFIG_FUNC (IOMUX_OCONFIG_FUNC | IOMUX_ICONFIG_FUNC)
-#define IOMUX_CONFIG_ALT1 (IOMUX_OCONFIG_ALT1 | IOMUX_ICONFIG_ALT1)
-#define IOMUX_CONFIG_ALT2 (IOMUX_OCONFIG_ALT2 | IOMUX_ICONFIG_ALT2)
-
-/*
- * various IOMUX pad functions
- */
-enum iomux_pad_config {
- PAD_CTL_NOLOOPBACK = 0x0 << 9,
- PAD_CTL_LOOPBACK = 0x1 << 9,
- PAD_CTL_PKE_NONE = 0x0 << 8,
- PAD_CTL_PKE_ENABLE = 0x1 << 8,
- PAD_CTL_PUE_KEEPER = 0x0 << 7,
- PAD_CTL_PUE_PUD = 0x1 << 7,
- PAD_CTL_100K_PD = 0x0 << 5,
- PAD_CTL_100K_PU = 0x1 << 5,
- PAD_CTL_47K_PU = 0x2 << 5,
- PAD_CTL_22K_PU = 0x3 << 5,
- PAD_CTL_HYS_CMOS = 0x0 << 4,
- PAD_CTL_HYS_SCHMITZ = 0x1 << 4,
- PAD_CTL_ODE_CMOS = 0x0 << 3,
- PAD_CTL_ODE_OpenDrain = 0x1 << 3,
- PAD_CTL_DRV_NORMAL = 0x0 << 1,
- PAD_CTL_DRV_HIGH = 0x1 << 1,
- PAD_CTL_DRV_MAX = 0x2 << 1,
- PAD_CTL_SRE_SLOW = 0x0 << 0,
- PAD_CTL_SRE_FAST = 0x1 << 0
-};
-
-/*
- * various IOMUX general purpose functions
- */
-enum iomux_gp_func {
- MUX_PGP_FIRI = 1 << 0,
- MUX_DDR_MODE = 1 << 1,
- MUX_PGP_CSPI_BB = 1 << 2,
- MUX_PGP_ATA_1 = 1 << 3,
- MUX_PGP_ATA_2 = 1 << 4,
- MUX_PGP_ATA_3 = 1 << 5,
- MUX_PGP_ATA_4 = 1 << 6,
- MUX_PGP_ATA_5 = 1 << 7,
- MUX_PGP_ATA_6 = 1 << 8,
- MUX_PGP_ATA_7 = 1 << 9,
- MUX_PGP_ATA_8 = 1 << 10,
- MUX_PGP_UH2 = 1 << 11,
- MUX_SDCTL_CSD0_SEL = 1 << 12,
- MUX_SDCTL_CSD1_SEL = 1 << 13,
- MUX_CSPI1_UART3 = 1 << 14,
- MUX_EXTDMAREQ2_MBX_SEL = 1 << 15,
- MUX_TAMPER_DETECT_EN = 1 << 16,
- MUX_PGP_USB_4WIRE = 1 << 17,
- MUX_PGP_USB_COMMON = 1 << 18,
- MUX_SDHC_MEMSTICK1 = 1 << 19,
- MUX_SDHC_MEMSTICK2 = 1 << 20,
- MUX_PGP_SPLL_BYP = 1 << 21,
- MUX_PGP_UPLL_BYP = 1 << 22,
- MUX_PGP_MSHC1_CLK_SEL = 1 << 23,
- MUX_PGP_MSHC2_CLK_SEL = 1 << 24,
- MUX_CSPI3_UART5_SEL = 1 << 25,
- MUX_PGP_ATA_9 = 1 << 26,
- MUX_PGP_USB_SUSPEND = 1 << 27,
- MUX_PGP_USB_OTG_LOOPBACK = 1 << 28,
- MUX_PGP_USB_HS1_LOOPBACK = 1 << 29,
- MUX_PGP_USB_HS2_LOOPBACK = 1 << 30,
- MUX_CLKO_DDR_MODE = 1 << 31,
-};
-
-/*
- * setups a single pin:
- * - reserves the pin so that it is not claimed by another driver
- * - setups the iomux according to the configuration
- * - if the pin is configured as a GPIO, we claim it through kernel gpiolib
- */
-int mxc_iomux_alloc_pin(unsigned int pin, const char *label);
-/*
- * setups multiple pins
- * convenient way to call the above function with tables
- */
-int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
- const char *label);
-
-/*
- * releases a single pin:
- * - make it available for a future use by another driver
- * - frees the GPIO if the pin was configured as GPIO
- * - DOES NOT reconfigure the IOMUX in its reset state
- */
-void mxc_iomux_release_pin(unsigned int pin);
-/*
- * releases multiple pins
- * convenvient way to call the above function with tables
- */
-void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count);
-
-/*
- * This function enables/disables the general purpose function for a particular
- * signal.
- */
-void mxc_iomux_set_gpr(enum iomux_gp_func, bool en);
-
-/*
- * This function only configures the iomux hardware.
- * It is called by the setup functions and should not be called directly anymore.
- * It is here visible for backward compatibility
- */
-void mxc_iomux_mode(unsigned int pin_mode);
-
-#define IOMUX_PADNUM_MASK 0x1ff
-#define IOMUX_GPIONUM_SHIFT 9
-#define IOMUX_GPIONUM_MASK (0xff << IOMUX_GPIONUM_SHIFT)
-#define IOMUX_MODE_SHIFT 17
-#define IOMUX_MODE_MASK (0xff << IOMUX_MODE_SHIFT)
-
-#define IOMUX_PIN(gpionum, padnum) \
- (((gpionum << IOMUX_GPIONUM_SHIFT) & IOMUX_GPIONUM_MASK) | \
- (padnum & IOMUX_PADNUM_MASK))
-
-#define IOMUX_MODE(pin, mode) (pin | mode << IOMUX_MODE_SHIFT)
-
-#define IOMUX_TO_GPIO(iomux_pin) \
- ((iomux_pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT)
-
-/*
- * This enumeration is constructed based on the Section
- * "sw_pad_ctl & sw_mux_ctl details" of the MX31 IC Spec. Each enumerated
- * value is constructed based on the rules described above.
- */
-
-enum iomux_pins {
- MX31_PIN_TTM_PAD = IOMUX_PIN(0xff, 0),
- MX31_PIN_CSPI3_SPI_RDY = IOMUX_PIN(0xff, 1),
- MX31_PIN_CSPI3_SCLK = IOMUX_PIN(0xff, 2),
- MX31_PIN_CSPI3_MISO = IOMUX_PIN(0xff, 3),
- MX31_PIN_CSPI3_MOSI = IOMUX_PIN(0xff, 4),
- MX31_PIN_CLKSS = IOMUX_PIN(0xff, 5),
- MX31_PIN_CE_CONTROL = IOMUX_PIN(0xff, 6),
- MX31_PIN_ATA_RESET_B = IOMUX_PIN(95, 7),
- MX31_PIN_ATA_DMACK = IOMUX_PIN(94, 8),
- MX31_PIN_ATA_DIOW = IOMUX_PIN(93, 9),
- MX31_PIN_ATA_DIOR = IOMUX_PIN(92, 10),
- MX31_PIN_ATA_CS1 = IOMUX_PIN(91, 11),
- MX31_PIN_ATA_CS0 = IOMUX_PIN(90, 12),
- MX31_PIN_SD1_DATA3 = IOMUX_PIN(63, 13),
- MX31_PIN_SD1_DATA2 = IOMUX_PIN(62, 14),
- MX31_PIN_SD1_DATA1 = IOMUX_PIN(61, 15),
- MX31_PIN_SD1_DATA0 = IOMUX_PIN(60, 16),
- MX31_PIN_SD1_CLK = IOMUX_PIN(59, 17),
- MX31_PIN_SD1_CMD = IOMUX_PIN(58, 18),
- MX31_PIN_D3_SPL = IOMUX_PIN(0xff, 19),
- MX31_PIN_D3_CLS = IOMUX_PIN(0xff, 20),
- MX31_PIN_D3_REV = IOMUX_PIN(0xff, 21),
- MX31_PIN_CONTRAST = IOMUX_PIN(0xff, 22),
- MX31_PIN_VSYNC3 = IOMUX_PIN(0xff, 23),
- MX31_PIN_READ = IOMUX_PIN(0xff, 24),
- MX31_PIN_WRITE = IOMUX_PIN(0xff, 25),
- MX31_PIN_PAR_RS = IOMUX_PIN(0xff, 26),
- MX31_PIN_SER_RS = IOMUX_PIN(89, 27),
- MX31_PIN_LCS1 = IOMUX_PIN(88, 28),
- MX31_PIN_LCS0 = IOMUX_PIN(87, 29),
- MX31_PIN_SD_D_CLK = IOMUX_PIN(86, 30),
- MX31_PIN_SD_D_IO = IOMUX_PIN(85, 31),
- MX31_PIN_SD_D_I = IOMUX_PIN(84, 32),
- MX31_PIN_DRDY0 = IOMUX_PIN(0xff, 33),
- MX31_PIN_FPSHIFT = IOMUX_PIN(0xff, 34),
- MX31_PIN_HSYNC = IOMUX_PIN(0xff, 35),
- MX31_PIN_VSYNC0 = IOMUX_PIN(0xff, 36),
- MX31_PIN_LD17 = IOMUX_PIN(0xff, 37),
- MX31_PIN_LD16 = IOMUX_PIN(0xff, 38),
- MX31_PIN_LD15 = IOMUX_PIN(0xff, 39),
- MX31_PIN_LD14 = IOMUX_PIN(0xff, 40),
- MX31_PIN_LD13 = IOMUX_PIN(0xff, 41),
- MX31_PIN_LD12 = IOMUX_PIN(0xff, 42),
- MX31_PIN_LD11 = IOMUX_PIN(0xff, 43),
- MX31_PIN_LD10 = IOMUX_PIN(0xff, 44),
- MX31_PIN_LD9 = IOMUX_PIN(0xff, 45),
- MX31_PIN_LD8 = IOMUX_PIN(0xff, 46),
- MX31_PIN_LD7 = IOMUX_PIN(0xff, 47),
- MX31_PIN_LD6 = IOMUX_PIN(0xff, 48),
- MX31_PIN_LD5 = IOMUX_PIN(0xff, 49),
- MX31_PIN_LD4 = IOMUX_PIN(0xff, 50),
- MX31_PIN_LD3 = IOMUX_PIN(0xff, 51),
- MX31_PIN_LD2 = IOMUX_PIN(0xff, 52),
- MX31_PIN_LD1 = IOMUX_PIN(0xff, 53),
- MX31_PIN_LD0 = IOMUX_PIN(0xff, 54),
- MX31_PIN_USBH2_DATA1 = IOMUX_PIN(0xff, 55),
- MX31_PIN_USBH2_DATA0 = IOMUX_PIN(0xff, 56),
- MX31_PIN_USBH2_NXT = IOMUX_PIN(0xff, 57),
- MX31_PIN_USBH2_STP = IOMUX_PIN(0xff, 58),
- MX31_PIN_USBH2_DIR = IOMUX_PIN(0xff, 59),
- MX31_PIN_USBH2_CLK = IOMUX_PIN(0xff, 60),
- MX31_PIN_USBOTG_DATA7 = IOMUX_PIN(0xff, 61),
- MX31_PIN_USBOTG_DATA6 = IOMUX_PIN(0xff, 62),
- MX31_PIN_USBOTG_DATA5 = IOMUX_PIN(0xff, 63),
- MX31_PIN_USBOTG_DATA4 = IOMUX_PIN(0xff, 64),
- MX31_PIN_USBOTG_DATA3 = IOMUX_PIN(0xff, 65),
- MX31_PIN_USBOTG_DATA2 = IOMUX_PIN(0xff, 66),
- MX31_PIN_USBOTG_DATA1 = IOMUX_PIN(0xff, 67),
- MX31_PIN_USBOTG_DATA0 = IOMUX_PIN(0xff, 68),
- MX31_PIN_USBOTG_NXT = IOMUX_PIN(0xff, 69),
- MX31_PIN_USBOTG_STP = IOMUX_PIN(0xff, 70),
- MX31_PIN_USBOTG_DIR = IOMUX_PIN(0xff, 71),
- MX31_PIN_USBOTG_CLK = IOMUX_PIN(0xff, 72),
- MX31_PIN_USB_BYP = IOMUX_PIN(31, 73),
- MX31_PIN_USB_OC = IOMUX_PIN(30, 74),
- MX31_PIN_USB_PWR = IOMUX_PIN(29, 75),
- MX31_PIN_SJC_MOD = IOMUX_PIN(0xff, 76),
- MX31_PIN_DE_B = IOMUX_PIN(0xff, 77),
- MX31_PIN_TRSTB = IOMUX_PIN(0xff, 78),
- MX31_PIN_TDO = IOMUX_PIN(0xff, 79),
- MX31_PIN_TDI = IOMUX_PIN(0xff, 80),
- MX31_PIN_TMS = IOMUX_PIN(0xff, 81),
- MX31_PIN_TCK = IOMUX_PIN(0xff, 82),
- MX31_PIN_RTCK = IOMUX_PIN(0xff, 83),
- MX31_PIN_KEY_COL7 = IOMUX_PIN(57, 84),
- MX31_PIN_KEY_COL6 = IOMUX_PIN(56, 85),
- MX31_PIN_KEY_COL5 = IOMUX_PIN(55, 86),
- MX31_PIN_KEY_COL4 = IOMUX_PIN(54, 87),
- MX31_PIN_KEY_COL3 = IOMUX_PIN(0xff, 88),
- MX31_PIN_KEY_COL2 = IOMUX_PIN(0xff, 89),
- MX31_PIN_KEY_COL1 = IOMUX_PIN(0xff, 90),
- MX31_PIN_KEY_COL0 = IOMUX_PIN(0xff, 91),
- MX31_PIN_KEY_ROW7 = IOMUX_PIN(53, 92),
- MX31_PIN_KEY_ROW6 = IOMUX_PIN(52, 93),
- MX31_PIN_KEY_ROW5 = IOMUX_PIN(51, 94),
- MX31_PIN_KEY_ROW4 = IOMUX_PIN(50, 95),
- MX31_PIN_KEY_ROW3 = IOMUX_PIN(0xff, 96),
- MX31_PIN_KEY_ROW2 = IOMUX_PIN(0xff, 97),
- MX31_PIN_KEY_ROW1 = IOMUX_PIN(0xff, 98),
- MX31_PIN_KEY_ROW0 = IOMUX_PIN(0xff, 99),
- MX31_PIN_BATT_LINE = IOMUX_PIN(49, 100),
- MX31_PIN_CTS2 = IOMUX_PIN(0xff, 101),
- MX31_PIN_RTS2 = IOMUX_PIN(0xff, 102),
- MX31_PIN_TXD2 = IOMUX_PIN(28, 103),
- MX31_PIN_RXD2 = IOMUX_PIN(27, 104),
- MX31_PIN_DTR_DCE2 = IOMUX_PIN(48, 105),
- MX31_PIN_DCD_DTE1 = IOMUX_PIN(47, 106),
- MX31_PIN_RI_DTE1 = IOMUX_PIN(46, 107),
- MX31_PIN_DSR_DTE1 = IOMUX_PIN(45, 108),
- MX31_PIN_DTR_DTE1 = IOMUX_PIN(44, 109),
- MX31_PIN_DCD_DCE1 = IOMUX_PIN(43, 110),
- MX31_PIN_RI_DCE1 = IOMUX_PIN(42, 111),
- MX31_PIN_DSR_DCE1 = IOMUX_PIN(41, 112),
- MX31_PIN_DTR_DCE1 = IOMUX_PIN(40, 113),
- MX31_PIN_CTS1 = IOMUX_PIN(39, 114),
- MX31_PIN_RTS1 = IOMUX_PIN(38, 115),
- MX31_PIN_TXD1 = IOMUX_PIN(37, 116),
- MX31_PIN_RXD1 = IOMUX_PIN(36, 117),
- MX31_PIN_CSPI2_SPI_RDY = IOMUX_PIN(0xff, 118),
- MX31_PIN_CSPI2_SCLK = IOMUX_PIN(0xff, 119),
- MX31_PIN_CSPI2_SS2 = IOMUX_PIN(0xff, 120),
- MX31_PIN_CSPI2_SS1 = IOMUX_PIN(0xff, 121),
- MX31_PIN_CSPI2_SS0 = IOMUX_PIN(0xff, 122),
- MX31_PIN_CSPI2_MISO = IOMUX_PIN(0xff, 123),
- MX31_PIN_CSPI2_MOSI = IOMUX_PIN(0xff, 124),
- MX31_PIN_CSPI1_SPI_RDY = IOMUX_PIN(0xff, 125),
- MX31_PIN_CSPI1_SCLK = IOMUX_PIN(0xff, 126),
- MX31_PIN_CSPI1_SS2 = IOMUX_PIN(0xff, 127),
- MX31_PIN_CSPI1_SS1 = IOMUX_PIN(0xff, 128),
- MX31_PIN_CSPI1_SS0 = IOMUX_PIN(0xff, 129),
- MX31_PIN_CSPI1_MISO = IOMUX_PIN(0xff, 130),
- MX31_PIN_CSPI1_MOSI = IOMUX_PIN(0xff, 131),
- MX31_PIN_SFS6 = IOMUX_PIN(26, 132),
- MX31_PIN_SCK6 = IOMUX_PIN(25, 133),
- MX31_PIN_SRXD6 = IOMUX_PIN(24, 134),
- MX31_PIN_STXD6 = IOMUX_PIN(23, 135),
- MX31_PIN_SFS5 = IOMUX_PIN(0xff, 136),
- MX31_PIN_SCK5 = IOMUX_PIN(0xff, 137),
- MX31_PIN_SRXD5 = IOMUX_PIN(22, 138),
- MX31_PIN_STXD5 = IOMUX_PIN(21, 139),
- MX31_PIN_SFS4 = IOMUX_PIN(0xff, 140),
- MX31_PIN_SCK4 = IOMUX_PIN(0xff, 141),
- MX31_PIN_SRXD4 = IOMUX_PIN(20, 142),
- MX31_PIN_STXD4 = IOMUX_PIN(19, 143),
- MX31_PIN_SFS3 = IOMUX_PIN(0xff, 144),
- MX31_PIN_SCK3 = IOMUX_PIN(0xff, 145),
- MX31_PIN_SRXD3 = IOMUX_PIN(18, 146),
- MX31_PIN_STXD3 = IOMUX_PIN(17, 147),
- MX31_PIN_I2C_DAT = IOMUX_PIN(0xff, 148),
- MX31_PIN_I2C_CLK = IOMUX_PIN(0xff, 149),
- MX31_PIN_CSI_PIXCLK = IOMUX_PIN(83, 150),
- MX31_PIN_CSI_HSYNC = IOMUX_PIN(82, 151),
- MX31_PIN_CSI_VSYNC = IOMUX_PIN(81, 152),
- MX31_PIN_CSI_MCLK = IOMUX_PIN(80, 153),
- MX31_PIN_CSI_D15 = IOMUX_PIN(79, 154),
- MX31_PIN_CSI_D14 = IOMUX_PIN(78, 155),
- MX31_PIN_CSI_D13 = IOMUX_PIN(77, 156),
- MX31_PIN_CSI_D12 = IOMUX_PIN(76, 157),
- MX31_PIN_CSI_D11 = IOMUX_PIN(75, 158),
- MX31_PIN_CSI_D10 = IOMUX_PIN(74, 159),
- MX31_PIN_CSI_D9 = IOMUX_PIN(73, 160),
- MX31_PIN_CSI_D8 = IOMUX_PIN(72, 161),
- MX31_PIN_CSI_D7 = IOMUX_PIN(71, 162),
- MX31_PIN_CSI_D6 = IOMUX_PIN(70, 163),
- MX31_PIN_CSI_D5 = IOMUX_PIN(69, 164),
- MX31_PIN_CSI_D4 = IOMUX_PIN(68, 165),
- MX31_PIN_M_GRANT = IOMUX_PIN(0xff, 166),
- MX31_PIN_M_REQUEST = IOMUX_PIN(0xff, 167),
- MX31_PIN_PC_POE = IOMUX_PIN(0xff, 168),
- MX31_PIN_PC_RW_B = IOMUX_PIN(0xff, 169),
- MX31_PIN_IOIS16 = IOMUX_PIN(0xff, 170),
- MX31_PIN_PC_RST = IOMUX_PIN(0xff, 171),
- MX31_PIN_PC_BVD2 = IOMUX_PIN(0xff, 172),
- MX31_PIN_PC_BVD1 = IOMUX_PIN(0xff, 173),
- MX31_PIN_PC_VS2 = IOMUX_PIN(0xff, 174),
- MX31_PIN_PC_VS1 = IOMUX_PIN(0xff, 175),
- MX31_PIN_PC_PWRON = IOMUX_PIN(0xff, 176),
- MX31_PIN_PC_READY = IOMUX_PIN(0xff, 177),
- MX31_PIN_PC_WAIT_B = IOMUX_PIN(0xff, 178),
- MX31_PIN_PC_CD2_B = IOMUX_PIN(0xff, 179),
- MX31_PIN_PC_CD1_B = IOMUX_PIN(0xff, 180),
- MX31_PIN_D0 = IOMUX_PIN(0xff, 181),
- MX31_PIN_D1 = IOMUX_PIN(0xff, 182),
- MX31_PIN_D2 = IOMUX_PIN(0xff, 183),
- MX31_PIN_D3 = IOMUX_PIN(0xff, 184),
- MX31_PIN_D4 = IOMUX_PIN(0xff, 185),
- MX31_PIN_D5 = IOMUX_PIN(0xff, 186),
- MX31_PIN_D6 = IOMUX_PIN(0xff, 187),
- MX31_PIN_D7 = IOMUX_PIN(0xff, 188),
- MX31_PIN_D8 = IOMUX_PIN(0xff, 189),
- MX31_PIN_D9 = IOMUX_PIN(0xff, 190),
- MX31_PIN_D10 = IOMUX_PIN(0xff, 191),
- MX31_PIN_D11 = IOMUX_PIN(0xff, 192),
- MX31_PIN_D12 = IOMUX_PIN(0xff, 193),
- MX31_PIN_D13 = IOMUX_PIN(0xff, 194),
- MX31_PIN_D14 = IOMUX_PIN(0xff, 195),
- MX31_PIN_D15 = IOMUX_PIN(0xff, 196),
- MX31_PIN_NFRB = IOMUX_PIN(16, 197),
- MX31_PIN_NFCE_B = IOMUX_PIN(15, 198),
- MX31_PIN_NFWP_B = IOMUX_PIN(14, 199),
- MX31_PIN_NFCLE = IOMUX_PIN(13, 200),
- MX31_PIN_NFALE = IOMUX_PIN(12, 201),
- MX31_PIN_NFRE_B = IOMUX_PIN(11, 202),
- MX31_PIN_NFWE_B = IOMUX_PIN(10, 203),
- MX31_PIN_SDQS3 = IOMUX_PIN(0xff, 204),
- MX31_PIN_SDQS2 = IOMUX_PIN(0xff, 205),
- MX31_PIN_SDQS1 = IOMUX_PIN(0xff, 206),
- MX31_PIN_SDQS0 = IOMUX_PIN(0xff, 207),
- MX31_PIN_SDCLK_B = IOMUX_PIN(0xff, 208),
- MX31_PIN_SDCLK = IOMUX_PIN(0xff, 209),
- MX31_PIN_SDCKE1 = IOMUX_PIN(0xff, 210),
- MX31_PIN_SDCKE0 = IOMUX_PIN(0xff, 211),
- MX31_PIN_SDWE = IOMUX_PIN(0xff, 212),
- MX31_PIN_CAS = IOMUX_PIN(0xff, 213),
- MX31_PIN_RAS = IOMUX_PIN(0xff, 214),
- MX31_PIN_RW = IOMUX_PIN(0xff, 215),
- MX31_PIN_BCLK = IOMUX_PIN(0xff, 216),
- MX31_PIN_LBA = IOMUX_PIN(0xff, 217),
- MX31_PIN_ECB = IOMUX_PIN(0xff, 218),
- MX31_PIN_CS5 = IOMUX_PIN(0xff, 219),
- MX31_PIN_CS4 = IOMUX_PIN(0xff, 220),
- MX31_PIN_CS3 = IOMUX_PIN(0xff, 221),
- MX31_PIN_CS2 = IOMUX_PIN(0xff, 222),
- MX31_PIN_CS1 = IOMUX_PIN(0xff, 223),
- MX31_PIN_CS0 = IOMUX_PIN(0xff, 224),
- MX31_PIN_OE = IOMUX_PIN(0xff, 225),
- MX31_PIN_EB1 = IOMUX_PIN(0xff, 226),
- MX31_PIN_EB0 = IOMUX_PIN(0xff, 227),
- MX31_PIN_DQM3 = IOMUX_PIN(0xff, 228),
- MX31_PIN_DQM2 = IOMUX_PIN(0xff, 229),
- MX31_PIN_DQM1 = IOMUX_PIN(0xff, 230),
- MX31_PIN_DQM0 = IOMUX_PIN(0xff, 231),
- MX31_PIN_SD31 = IOMUX_PIN(0xff, 232),
- MX31_PIN_SD30 = IOMUX_PIN(0xff, 233),
- MX31_PIN_SD29 = IOMUX_PIN(0xff, 234),
- MX31_PIN_SD28 = IOMUX_PIN(0xff, 235),
- MX31_PIN_SD27 = IOMUX_PIN(0xff, 236),
- MX31_PIN_SD26 = IOMUX_PIN(0xff, 237),
- MX31_PIN_SD25 = IOMUX_PIN(0xff, 238),
- MX31_PIN_SD24 = IOMUX_PIN(0xff, 239),
- MX31_PIN_SD23 = IOMUX_PIN(0xff, 240),
- MX31_PIN_SD22 = IOMUX_PIN(0xff, 241),
- MX31_PIN_SD21 = IOMUX_PIN(0xff, 242),
- MX31_PIN_SD20 = IOMUX_PIN(0xff, 243),
- MX31_PIN_SD19 = IOMUX_PIN(0xff, 244),
- MX31_PIN_SD18 = IOMUX_PIN(0xff, 245),
- MX31_PIN_SD17 = IOMUX_PIN(0xff, 246),
- MX31_PIN_SD16 = IOMUX_PIN(0xff, 247),
- MX31_PIN_SD15 = IOMUX_PIN(0xff, 248),
- MX31_PIN_SD14 = IOMUX_PIN(0xff, 249),
- MX31_PIN_SD13 = IOMUX_PIN(0xff, 250),
- MX31_PIN_SD12 = IOMUX_PIN(0xff, 251),
- MX31_PIN_SD11 = IOMUX_PIN(0xff, 252),
- MX31_PIN_SD10 = IOMUX_PIN(0xff, 253),
- MX31_PIN_SD9 = IOMUX_PIN(0xff, 254),
- MX31_PIN_SD8 = IOMUX_PIN(0xff, 255),
- MX31_PIN_SD7 = IOMUX_PIN(0xff, 256),
- MX31_PIN_SD6 = IOMUX_PIN(0xff, 257),
- MX31_PIN_SD5 = IOMUX_PIN(0xff, 258),
- MX31_PIN_SD4 = IOMUX_PIN(0xff, 259),
- MX31_PIN_SD3 = IOMUX_PIN(0xff, 260),
- MX31_PIN_SD2 = IOMUX_PIN(0xff, 261),
- MX31_PIN_SD1 = IOMUX_PIN(0xff, 262),
- MX31_PIN_SD0 = IOMUX_PIN(0xff, 263),
- MX31_PIN_SDBA0 = IOMUX_PIN(0xff, 264),
- MX31_PIN_SDBA1 = IOMUX_PIN(0xff, 265),
- MX31_PIN_A25 = IOMUX_PIN(0xff, 266),
- MX31_PIN_A24 = IOMUX_PIN(0xff, 267),
- MX31_PIN_A23 = IOMUX_PIN(0xff, 268),
- MX31_PIN_A22 = IOMUX_PIN(0xff, 269),
- MX31_PIN_A21 = IOMUX_PIN(0xff, 270),
- MX31_PIN_A20 = IOMUX_PIN(0xff, 271),
- MX31_PIN_A19 = IOMUX_PIN(0xff, 272),
- MX31_PIN_A18 = IOMUX_PIN(0xff, 273),
- MX31_PIN_A17 = IOMUX_PIN(0xff, 274),
- MX31_PIN_A16 = IOMUX_PIN(0xff, 275),
- MX31_PIN_A14 = IOMUX_PIN(0xff, 276),
- MX31_PIN_A15 = IOMUX_PIN(0xff, 277),
- MX31_PIN_A13 = IOMUX_PIN(0xff, 278),
- MX31_PIN_A12 = IOMUX_PIN(0xff, 279),
- MX31_PIN_A11 = IOMUX_PIN(0xff, 280),
- MX31_PIN_MA10 = IOMUX_PIN(0xff, 281),
- MX31_PIN_A10 = IOMUX_PIN(0xff, 282),
- MX31_PIN_A9 = IOMUX_PIN(0xff, 283),
- MX31_PIN_A8 = IOMUX_PIN(0xff, 284),
- MX31_PIN_A7 = IOMUX_PIN(0xff, 285),
- MX31_PIN_A6 = IOMUX_PIN(0xff, 286),
- MX31_PIN_A5 = IOMUX_PIN(0xff, 287),
- MX31_PIN_A4 = IOMUX_PIN(0xff, 288),
- MX31_PIN_A3 = IOMUX_PIN(0xff, 289),
- MX31_PIN_A2 = IOMUX_PIN(0xff, 290),
- MX31_PIN_A1 = IOMUX_PIN(0xff, 291),
- MX31_PIN_A0 = IOMUX_PIN(0xff, 292),
- MX31_PIN_VPG1 = IOMUX_PIN(0xff, 293),
- MX31_PIN_VPG0 = IOMUX_PIN(0xff, 294),
- MX31_PIN_DVFS1 = IOMUX_PIN(0xff, 295),
- MX31_PIN_DVFS0 = IOMUX_PIN(0xff, 296),
- MX31_PIN_VSTBY = IOMUX_PIN(0xff, 297),
- MX31_PIN_POWER_FAIL = IOMUX_PIN(0xff, 298),
- MX31_PIN_CKIL = IOMUX_PIN(0xff, 299),
- MX31_PIN_BOOT_MODE4 = IOMUX_PIN(0xff, 300),
- MX31_PIN_BOOT_MODE3 = IOMUX_PIN(0xff, 301),
- MX31_PIN_BOOT_MODE2 = IOMUX_PIN(0xff, 302),
- MX31_PIN_BOOT_MODE1 = IOMUX_PIN(0xff, 303),
- MX31_PIN_BOOT_MODE0 = IOMUX_PIN(0xff, 304),
- MX31_PIN_CLKO = IOMUX_PIN(0xff, 305),
- MX31_PIN_POR_B = IOMUX_PIN(0xff, 306),
- MX31_PIN_RESET_IN_B = IOMUX_PIN(0xff, 307),
- MX31_PIN_CKIH = IOMUX_PIN(0xff, 308),
- MX31_PIN_SIMPD0 = IOMUX_PIN(35, 309),
- MX31_PIN_SRX0 = IOMUX_PIN(34, 310),
- MX31_PIN_STX0 = IOMUX_PIN(33, 311),
- MX31_PIN_SVEN0 = IOMUX_PIN(32, 312),
- MX31_PIN_SRST0 = IOMUX_PIN(67, 313),
- MX31_PIN_SCLK0 = IOMUX_PIN(66, 314),
- MX31_PIN_GPIO3_1 = IOMUX_PIN(65, 315),
- MX31_PIN_GPIO3_0 = IOMUX_PIN(64, 316),
- MX31_PIN_GPIO1_6 = IOMUX_PIN( 6, 317),
- MX31_PIN_GPIO1_5 = IOMUX_PIN( 5, 318),
- MX31_PIN_GPIO1_4 = IOMUX_PIN( 4, 319),
- MX31_PIN_GPIO1_3 = IOMUX_PIN( 3, 320),
- MX31_PIN_GPIO1_2 = IOMUX_PIN( 2, 321),
- MX31_PIN_GPIO1_1 = IOMUX_PIN( 1, 322),
- MX31_PIN_GPIO1_0 = IOMUX_PIN( 0, 323),
- MX31_PIN_PWMO = IOMUX_PIN( 9, 324),
- MX31_PIN_WATCHDOG_RST = IOMUX_PIN(0xff, 325),
- MX31_PIN_COMPARE = IOMUX_PIN( 8, 326),
- MX31_PIN_CAPTURE = IOMUX_PIN( 7, 327),
-};
-
-#define PIN_MAX 327
-#define NB_PORTS 12 /* NB_PINS/32, we chose 32 pins per "PORT" */
-
-/*
- * Convenience values for use with mxc_iomux_mode()
- *
- * Format here is MX31_PIN_(pin name)__(function)
- */
-#define MX31_PIN_CSPI3_MOSI__RXD3 IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_MISO__TXD3 IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_SCLK__RTS3 IOMUX_MODE(MX31_PIN_CSPI3_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_SPI_RDY__CTS3 IOMUX_MODE(MX31_PIN_CSPI3_SPI_RDY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CTS1__CTS1 IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS1__RTS1 IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS1__SFS IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_TXD1__TXD1 IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_TXD1__SCK IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_RXD1__RXD1 IOMUX_MODE(MX31_PIN_RXD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RXD1__STXDA IOMUX_MODE(MX31_PIN_RXD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_DCD_DCE1__DCD_DCE1 IOMUX_MODE(MX31_PIN_DCD_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RI_DCE1__RI_DCE1 IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DSR_DCE1__DSR_DCE1 IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DTR_DCE1__DTR_DCE1 IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DTR_DCE1__SRXDA IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CTS2__CTS2 IOMUX_MODE(MX31_PIN_CTS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS2__RTS2 IOMUX_MODE(MX31_PIN_RTS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_TXD2__TXD2 IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RXD2__RXD2 IOMUX_MODE(MX31_PIN_RXD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DCD_DTE1__DCD_DTE2 IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_RI_DTE1__RI_DTE2 IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_DSR_DTE1__DSR_DTE2 IOMUX_MODE(MX31_PIN_DSR_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_DTR_DTE1__DTR_DTE2 IOMUX_MODE(MX31_PIN_DTR_DTE1, IOMUX_OCONFIG_ALT3 | IOMUX_ICONFIG_NONE)
-#define MX31_PIN_PC_RST__CTS5 IOMUX_MODE(MX31_PIN_PC_RST, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_VS2__RTS5 IOMUX_MODE(MX31_PIN_PC_VS2, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_BVD2__TXD5 IOMUX_MODE(MX31_PIN_PC_BVD2, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_BVD1__RXD5 IOMUX_MODE(MX31_PIN_PC_BVD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CSPI1_MOSI__MOSI IOMUX_MODE(MX31_PIN_CSPI1_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_MISO__MISO IOMUX_MODE(MX31_PIN_CSPI1_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SCLK__SCLK IOMUX_MODE(MX31_PIN_CSPI1_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SPI_RDY__SPI_RDY IOMUX_MODE(MX31_PIN_CSPI1_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS0__SS0 IOMUX_MODE(MX31_PIN_CSPI1_SS0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS1__SS1 IOMUX_MODE(MX31_PIN_CSPI1_SS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS2__SS2 IOMUX_MODE(MX31_PIN_CSPI1_SS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MOSI__MOSI IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MOSI__SCL IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_MISO__MISO IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MISO__SDA IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_SCLK__SCLK IOMUX_MODE(MX31_PIN_CSPI2_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SPI_RDY__SPI_RDY IOMUX_MODE(MX31_PIN_CSPI2_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS0__SS0 IOMUX_MODE(MX31_PIN_CSPI2_SS0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS1__SS1 IOMUX_MODE(MX31_PIN_CSPI2_SS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS2__SS2 IOMUX_MODE(MX31_PIN_CSPI2_SS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_MOSI__MOSI IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_MISO__MISO IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_SCLK__SCLK IOMUX_MODE(MX31_PIN_CSPI3_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_SPI_RDY__SPI_RDY IOMUX_MODE(MX31_PIN_CSPI3_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_BATT_LINE__OWIRE IOMUX_MODE(MX31_PIN_BATT_LINE, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CS4__CS4 IOMUX_MODE(MX31_PIN_CS4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA3__SD1_DATA3 IOMUX_MODE(MX31_PIN_SD1_DATA3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA2__SD1_DATA2 IOMUX_MODE(MX31_PIN_SD1_DATA2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA1__SD1_DATA1 IOMUX_MODE(MX31_PIN_SD1_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA0__SD1_DATA0 IOMUX_MODE(MX31_PIN_SD1_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_CLK__SD1_CLK IOMUX_MODE(MX31_PIN_SD1_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_CMD__SD1_CMD IOMUX_MODE(MX31_PIN_SD1_CMD, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_ATA_CS0__GPIO3_26 IOMUX_MODE(MX31_PIN_ATA_CS0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_ATA_CS1__GPIO3_27 IOMUX_MODE(MX31_PIN_ATA_CS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_PC_PWRON__SD2_DATA3 IOMUX_MODE(MX31_PIN_PC_PWRON, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_VS1__SD2_DATA2 IOMUX_MODE(MX31_PIN_PC_VS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_READY__SD2_DATA1 IOMUX_MODE(MX31_PIN_PC_READY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_WAIT_B__SD2_DATA0 IOMUX_MODE(MX31_PIN_PC_WAIT_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_CD2_B__SD2_CLK IOMUX_MODE(MX31_PIN_PC_CD2_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_CD1_B__SD2_CMD IOMUX_MODE(MX31_PIN_PC_CD1_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_ATA_DIOR__GPIO3_28 IOMUX_MODE(MX31_PIN_ATA_DIOR, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_ATA_DIOW__GPIO3_29 IOMUX_MODE(MX31_PIN_ATA_DIOW, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_LD0__LD0 IOMUX_MODE(MX31_PIN_LD0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD1__LD1 IOMUX_MODE(MX31_PIN_LD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD2__LD2 IOMUX_MODE(MX31_PIN_LD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD3__LD3 IOMUX_MODE(MX31_PIN_LD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD4__LD4 IOMUX_MODE(MX31_PIN_LD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD5__LD5 IOMUX_MODE(MX31_PIN_LD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD6__LD6 IOMUX_MODE(MX31_PIN_LD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD7__LD7 IOMUX_MODE(MX31_PIN_LD7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD8__LD8 IOMUX_MODE(MX31_PIN_LD8, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD9__LD9 IOMUX_MODE(MX31_PIN_LD9, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD10__LD10 IOMUX_MODE(MX31_PIN_LD10, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD11__LD11 IOMUX_MODE(MX31_PIN_LD11, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD12__LD12 IOMUX_MODE(MX31_PIN_LD12, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD13__LD13 IOMUX_MODE(MX31_PIN_LD13, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD14__LD14 IOMUX_MODE(MX31_PIN_LD14, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD15__LD15 IOMUX_MODE(MX31_PIN_LD15, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD16__LD16 IOMUX_MODE(MX31_PIN_LD16, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD17__LD17 IOMUX_MODE(MX31_PIN_LD17, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_VSYNC3__VSYNC3 IOMUX_MODE(MX31_PIN_VSYNC3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_HSYNC__HSYNC IOMUX_MODE(MX31_PIN_HSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_FPSHIFT__FPSHIFT IOMUX_MODE(MX31_PIN_FPSHIFT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DRDY0__DRDY0 IOMUX_MODE(MX31_PIN_DRDY0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_REV__D3_REV IOMUX_MODE(MX31_PIN_D3_REV, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CONTRAST__CONTRAST IOMUX_MODE(MX31_PIN_CONTRAST, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_SPL__D3_SPL IOMUX_MODE(MX31_PIN_D3_SPL, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_CLS__D3_CLS IOMUX_MODE(MX31_PIN_D3_CLS, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO1_1__GPIO IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DCD_DTE1__I2C2_SDA IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_RI_DTE1__I2C2_SCL IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CSPI2_SS2__I2C3_SDA IOMUX_MODE(MX31_PIN_CSPI2_SS2, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_SCLK__I2C3_SCL IOMUX_MODE(MX31_PIN_CSPI2_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSI_D4__CSI_D4 IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D5__CSI_D5 IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D6__CSI_D6 IOMUX_MODE(MX31_PIN_CSI_D6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D7__CSI_D7 IOMUX_MODE(MX31_PIN_CSI_D7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D8__CSI_D8 IOMUX_MODE(MX31_PIN_CSI_D8, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D9__CSI_D9 IOMUX_MODE(MX31_PIN_CSI_D9, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D10__CSI_D10 IOMUX_MODE(MX31_PIN_CSI_D10, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D11__CSI_D11 IOMUX_MODE(MX31_PIN_CSI_D11, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D12__CSI_D12 IOMUX_MODE(MX31_PIN_CSI_D12, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D13__CSI_D13 IOMUX_MODE(MX31_PIN_CSI_D13, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D14__CSI_D14 IOMUX_MODE(MX31_PIN_CSI_D14, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D15__CSI_D15 IOMUX_MODE(MX31_PIN_CSI_D15, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_HSYNC__CSI_HSYNC IOMUX_MODE(MX31_PIN_CSI_HSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_MCLK__CSI_MCLK IOMUX_MODE(MX31_PIN_CSI_MCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_PIXCLK__CSI_PIXCLK IOMUX_MODE(MX31_PIN_CSI_PIXCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_VSYNC__CSI_VSYNC IOMUX_MODE(MX31_PIN_CSI_VSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO3_0__GPIO3_0 IOMUX_MODE(MX31_PIN_GPIO3_0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_GPIO3_1__GPIO3_1 IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_TXD2__GPIO1_28 IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSI_D4__GPIO3_4 IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSI_D5__GPIO3_5 IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USBOTG_DATA0__USBOTG_DATA0 IOMUX_MODE(MX31_PIN_USBOTG_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA1__USBOTG_DATA1 IOMUX_MODE(MX31_PIN_USBOTG_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA2__USBOTG_DATA2 IOMUX_MODE(MX31_PIN_USBOTG_DATA2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA3__USBOTG_DATA3 IOMUX_MODE(MX31_PIN_USBOTG_DATA3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA4__USBOTG_DATA4 IOMUX_MODE(MX31_PIN_USBOTG_DATA4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA5__USBOTG_DATA5 IOMUX_MODE(MX31_PIN_USBOTG_DATA5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA6__USBOTG_DATA6 IOMUX_MODE(MX31_PIN_USBOTG_DATA6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA7__USBOTG_DATA7 IOMUX_MODE(MX31_PIN_USBOTG_DATA7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_CLK__USBOTG_CLK IOMUX_MODE(MX31_PIN_USBOTG_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DIR__USBOTG_DIR IOMUX_MODE(MX31_PIN_USBOTG_DIR, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_NXT__USBOTG_NXT IOMUX_MODE(MX31_PIN_USBOTG_NXT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_STP__USBOTG_STP IOMUX_MODE(MX31_PIN_USBOTG_STP, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_MOSI__USBH1_RXDM IOMUX_MODE(MX31_PIN_CSPI1_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_MISO__USBH1_RXDP IOMUX_MODE(MX31_PIN_CSPI1_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS0__USBH1_TXDM IOMUX_MODE(MX31_PIN_CSPI1_SS0, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS1__USBH1_TXDP IOMUX_MODE(MX31_PIN_CSPI1_SS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS2__USBH1_RCV IOMUX_MODE(MX31_PIN_CSPI1_SS2, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SCLK__USBH1_OEB IOMUX_MODE(MX31_PIN_CSPI1_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SPI_RDY__USBH1_FS IOMUX_MODE(MX31_PIN_CSPI1_SPI_RDY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_SFS6__USBH1_SUSPEND IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_NFRE_B__GPIO1_11 IOMUX_MODE(MX31_PIN_NFRE_B, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_NFALE__GPIO1_12 IOMUX_MODE(MX31_PIN_NFALE, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USBH2_DATA0__USBH2_DATA0 IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_DATA1__USBH2_DATA1 IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD3__USBH2_DATA2 IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD3__USBH2_DATA3 IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK3__USBH2_DATA4 IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS3__USBH2_DATA5 IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD6__USBH2_DATA6 IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD6__USBH2_DATA7 IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_CLK__USBH2_CLK IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_DIR__USBH2_DIR IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_NXT__USBH2_NXT IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_STP__USBH2_STP IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK6__GPIO1_25 IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USB_OC__GPIO1_30 IOMUX_MODE(MX31_PIN_USB_OC, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_I2C_DAT__I2C1_SDA IOMUX_MODE(MX31_PIN_I2C_DAT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_I2C_CLK__I2C1_SCL IOMUX_MODE(MX31_PIN_I2C_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO1_0__GPIO1_0 IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SVEN0__GPIO2_0 IOMUX_MODE(MX31_PIN_SVEN0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STX0__GPIO2_1 IOMUX_MODE(MX31_PIN_STX0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SRX0__GPIO2_2 IOMUX_MODE(MX31_PIN_SRX0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SIMPD0__GPIO2_3 IOMUX_MODE(MX31_PIN_SIMPD0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DTR_DCE1__GPIO2_8 IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DSR_DCE1__GPIO2_9 IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_RI_DCE1__GPIO2_10 IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DCD_DCE1__GPIO2_11 IOMUX_MODE(MX31_PIN_DCD_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STXD5__GPIO1_21 IOMUX_MODE(MX31_PIN_STXD5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SRXD5__GPIO1_22 IOMUX_MODE(MX31_PIN_SRXD5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_GPIO1_3__GPIO1_3 IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSPI2_SS1__CSPI3_SS1 IOMUX_MODE(MX31_PIN_CSPI2_SS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_RTS1__GPIO2_6 IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CTS1__GPIO2_7 IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_LCS0__GPIO3_23 IOMUX_MODE(MX31_PIN_LCS0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STXD4__STXD4 IOMUX_MODE(MX31_PIN_STXD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD4__SRXD4 IOMUX_MODE(MX31_PIN_SRXD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK4__SCK4 IOMUX_MODE(MX31_PIN_SCK4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS4__SFS4 IOMUX_MODE(MX31_PIN_SFS4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD5__STXD5 IOMUX_MODE(MX31_PIN_STXD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD5__SRXD5 IOMUX_MODE(MX31_PIN_SRXD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK5__SCK5 IOMUX_MODE(MX31_PIN_SCK5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS5__SFS5 IOMUX_MODE(MX31_PIN_SFS5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW0_KEY_ROW0 IOMUX_MODE(MX31_PIN_KEY_ROW0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW1_KEY_ROW1 IOMUX_MODE(MX31_PIN_KEY_ROW1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW2_KEY_ROW2 IOMUX_MODE(MX31_PIN_KEY_ROW2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW3_KEY_ROW3 IOMUX_MODE(MX31_PIN_KEY_ROW3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW4_KEY_ROW4 IOMUX_MODE(MX31_PIN_KEY_ROW4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW4_GPIO IOMUX_MODE(MX31_PIN_KEY_ROW4, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_KEY_ROW5_KEY_ROW5 IOMUX_MODE(MX31_PIN_KEY_ROW5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW6_KEY_ROW6 IOMUX_MODE(MX31_PIN_KEY_ROW6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW7_KEY_ROW7 IOMUX_MODE(MX31_PIN_KEY_ROW7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL0_KEY_COL0 IOMUX_MODE(MX31_PIN_KEY_COL0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL1_KEY_COL1 IOMUX_MODE(MX31_PIN_KEY_COL1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL2_KEY_COL2 IOMUX_MODE(MX31_PIN_KEY_COL2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL3_KEY_COL3 IOMUX_MODE(MX31_PIN_KEY_COL3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL4_KEY_COL4 IOMUX_MODE(MX31_PIN_KEY_COL4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL5_KEY_COL5 IOMUX_MODE(MX31_PIN_KEY_COL5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL6_KEY_COL6 IOMUX_MODE(MX31_PIN_KEY_COL6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL7_KEY_COL7 IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_WATCHDOG_RST__WATCHDOG_RST IOMUX_MODE(MX31_PIN_WATCHDOG_RST, IOMUX_CONFIG_FUNC)
-
-
-/*
- * XXX: The SS0, SS1, SS2, SS3 lines of spi3 are multiplexed with cspi2_ss0,
- * cspi2_ss1, cspi1_ss0 cspi1_ss1
- */
-
-/*
- * This function configures the pad value for a IOMUX pin.
- */
-void mxc_iomux_set_pad(enum iomux_pins, u32);
-
-#endif /* ifndef __MACH_IOMUX_MX3_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx35.h b/arch/arm/mach-imx/iomux-mx35.h
deleted file mode 100644
index 7fb5259..0000000
--- a/arch/arm/mach-imx/iomux-mx35.h
+++ /dev/null
@@ -1,1254 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH <armlinux@phytec.de>
- */
-
-#ifndef __MACH_IOMUX_MX35_H__
-#define __MACH_IOMUX_MX35_H__
-
-#include "iomux-v3.h"
-
-/*
- * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode>
- * If <padname> or <padmode> refers to a GPIO, it is named
- * GPIO_<unit>_<num> see also iomux-v3.h
- */
-
-/* PAD MUX ALT INPSE PATH */
-#define MX35_PAD_CAPTURE__GPT_CAPIN1 IOMUX_PAD(0x328, 0x004, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__GPT_CMPOUT2 IOMUX_PAD(0x328, 0x004, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__CSPI2_SS1 IOMUX_PAD(0x328, 0x004, 2, 0x7f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__EPIT1_EPITO IOMUX_PAD(0x328, 0x004, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__CCM_CLK32K IOMUX_PAD(0x328, 0x004, 4, 0x7d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__GPIO1_4 IOMUX_PAD(0x328, 0x004, 5, 0x850, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_COMPARE__GPT_CMPOUT1 IOMUX_PAD(0x32c, 0x008, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPT_CAPIN2 IOMUX_PAD(0x32c, 0x008, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPT_CMPOUT3 IOMUX_PAD(0x32c, 0x008, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__EPIT2_EPITO IOMUX_PAD(0x32c, 0x008, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPIO1_5 IOMUX_PAD(0x32c, 0x008, 5, 0x854, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__SDMA_EXTDMA_2 IOMUX_PAD(0x32c, 0x008, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_WDOG_RST__WDOG_WDOG_B IOMUX_PAD(0x330, 0x00c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_WDOG_RST__IPU_FLASH_STROBE IOMUX_PAD(0x330, 0x00c, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_WDOG_RST__GPIO1_6 IOMUX_PAD(0x330, 0x00c, 5, 0x858, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO1_0__GPIO1_0 IOMUX_PAD(0x334, 0x010, 0, 0x82c, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__CCM_PMIC_RDY IOMUX_PAD(0x334, 0x010, 1, 0x7d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__OWIRE_LINE IOMUX_PAD(0x334, 0x010, 2, 0x990, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__SDMA_EXTDMA_0 IOMUX_PAD(0x334, 0x010, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO1_1__GPIO1_1 IOMUX_PAD(0x338, 0x014, 0, 0x838, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__PWM_PWMO IOMUX_PAD(0x338, 0x014, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__CSPI1_SS2 IOMUX_PAD(0x338, 0x014, 3, 0x7d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__SCC_TAMPER_DETECT IOMUX_PAD(0x338, 0x014, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__SDMA_EXTDMA_1 IOMUX_PAD(0x338, 0x014, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO2_0__GPIO2_0 IOMUX_PAD(0x33c, 0x018, 0, 0x868, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO2_0__USB_TOP_USBOTG_CLK IOMUX_PAD(0x33c, 0x018, 1, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO3_0__GPIO3_0 IOMUX_PAD(0x340, 0x01c, 0, 0x8e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO3_0__USB_TOP_USBH2_CLK IOMUX_PAD(0x340, 0x01c, 1, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RESET_IN_B__CCM_RESET_IN_B IOMUX_PAD(0x344, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_POR_B__CCM_POR_B IOMUX_PAD(0x348, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLKO__CCM_CLKO IOMUX_PAD(0x34c, 0x020, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CLKO__GPIO1_8 IOMUX_PAD(0x34c, 0x020, 5, 0x860, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_BOOT_MODE0__CCM_BOOT_MODE_0 IOMUX_PAD(0x350, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_BOOT_MODE1__CCM_BOOT_MODE_1 IOMUX_PAD(0x354, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLK_MODE0__CCM_CLK_MODE_0 IOMUX_PAD(0x358, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLK_MODE1__CCM_CLK_MODE_1 IOMUX_PAD(0x35c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_POWER_FAIL__CCM_DSM_WAKEUP_INT_26 IOMUX_PAD(0x360, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_VSTBY__CCM_VSTBY IOMUX_PAD(0x364, 0x024, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_VSTBY__GPIO1_7 IOMUX_PAD(0x364, 0x024, 5, 0x85c, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A0__EMI_EIM_DA_L_0 IOMUX_PAD(0x368, 0x028, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A1__EMI_EIM_DA_L_1 IOMUX_PAD(0x36c, 0x02c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A2__EMI_EIM_DA_L_2 IOMUX_PAD(0x370, 0x030, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A3__EMI_EIM_DA_L_3 IOMUX_PAD(0x374, 0x034, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A4__EMI_EIM_DA_L_4 IOMUX_PAD(0x378, 0x038, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A5__EMI_EIM_DA_L_5 IOMUX_PAD(0x37c, 0x03c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A6__EMI_EIM_DA_L_6 IOMUX_PAD(0x380, 0x040, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A7__EMI_EIM_DA_L_7 IOMUX_PAD(0x384, 0x044, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A8__EMI_EIM_DA_H_8 IOMUX_PAD(0x388, 0x048, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A9__EMI_EIM_DA_H_9 IOMUX_PAD(0x38c, 0x04c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A10__EMI_EIM_DA_H_10 IOMUX_PAD(0x390, 0x050, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_MA10__EMI_MA10 IOMUX_PAD(0x394, 0x054, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A11__EMI_EIM_DA_H_11 IOMUX_PAD(0x398, 0x058, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A12__EMI_EIM_DA_H_12 IOMUX_PAD(0x39c, 0x05c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A13__EMI_EIM_DA_H_13 IOMUX_PAD(0x3a0, 0x060, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A14__EMI_EIM_DA_H2_14 IOMUX_PAD(0x3a4, 0x064, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A15__EMI_EIM_DA_H2_15 IOMUX_PAD(0x3a8, 0x068, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A16__EMI_EIM_A_16 IOMUX_PAD(0x3ac, 0x06c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A17__EMI_EIM_A_17 IOMUX_PAD(0x3b0, 0x070, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A18__EMI_EIM_A_18 IOMUX_PAD(0x3b4, 0x074, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A19__EMI_EIM_A_19 IOMUX_PAD(0x3b8, 0x078, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A20__EMI_EIM_A_20 IOMUX_PAD(0x3bc, 0x07c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A21__EMI_EIM_A_21 IOMUX_PAD(0x3c0, 0x080, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A22__EMI_EIM_A_22 IOMUX_PAD(0x3c4, 0x084, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A23__EMI_EIM_A_23 IOMUX_PAD(0x3c8, 0x088, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A24__EMI_EIM_A_24 IOMUX_PAD(0x3cc, 0x08c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A25__EMI_EIM_A_25 IOMUX_PAD(0x3d0, 0x090, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDBA1__EMI_EIM_SDBA1 IOMUX_PAD(0x3d4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDBA0__EMI_EIM_SDBA0 IOMUX_PAD(0x3d8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD0__EMI_DRAM_D_0 IOMUX_PAD(0x3dc, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1__EMI_DRAM_D_1 IOMUX_PAD(0x3e0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2__EMI_DRAM_D_2 IOMUX_PAD(0x3e4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD3__EMI_DRAM_D_3 IOMUX_PAD(0x3e8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD4__EMI_DRAM_D_4 IOMUX_PAD(0x3ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD5__EMI_DRAM_D_5 IOMUX_PAD(0x3f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD6__EMI_DRAM_D_6 IOMUX_PAD(0x3f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD7__EMI_DRAM_D_7 IOMUX_PAD(0x3f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD8__EMI_DRAM_D_8 IOMUX_PAD(0x3fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD9__EMI_DRAM_D_9 IOMUX_PAD(0x400, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD10__EMI_DRAM_D_10 IOMUX_PAD(0x404, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD11__EMI_DRAM_D_11 IOMUX_PAD(0x408, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD12__EMI_DRAM_D_12 IOMUX_PAD(0x40c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD13__EMI_DRAM_D_13 IOMUX_PAD(0x410, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD14__EMI_DRAM_D_14 IOMUX_PAD(0x414, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD15__EMI_DRAM_D_15 IOMUX_PAD(0x418, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD16__EMI_DRAM_D_16 IOMUX_PAD(0x41c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD17__EMI_DRAM_D_17 IOMUX_PAD(0x420, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD18__EMI_DRAM_D_18 IOMUX_PAD(0x424, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD19__EMI_DRAM_D_19 IOMUX_PAD(0x428, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD20__EMI_DRAM_D_20 IOMUX_PAD(0x42c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD21__EMI_DRAM_D_21 IOMUX_PAD(0x430, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD22__EMI_DRAM_D_22 IOMUX_PAD(0x434, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD23__EMI_DRAM_D_23 IOMUX_PAD(0x438, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD24__EMI_DRAM_D_24 IOMUX_PAD(0x43c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD25__EMI_DRAM_D_25 IOMUX_PAD(0x440, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD26__EMI_DRAM_D_26 IOMUX_PAD(0x444, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD27__EMI_DRAM_D_27 IOMUX_PAD(0x448, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD28__EMI_DRAM_D_28 IOMUX_PAD(0x44c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD29__EMI_DRAM_D_29 IOMUX_PAD(0x450, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD30__EMI_DRAM_D_30 IOMUX_PAD(0x454, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD31__EMI_DRAM_D_31 IOMUX_PAD(0x458, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM0__EMI_DRAM_DQM_0 IOMUX_PAD(0x45c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM1__EMI_DRAM_DQM_1 IOMUX_PAD(0x460, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM2__EMI_DRAM_DQM_2 IOMUX_PAD(0x464, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM3__EMI_DRAM_DQM_3 IOMUX_PAD(0x468, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_EB0__EMI_EIM_EB0_B IOMUX_PAD(0x46c, 0x094, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_EB1__EMI_EIM_EB1_B IOMUX_PAD(0x470, 0x098, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_OE__EMI_EIM_OE IOMUX_PAD(0x474, 0x09c, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS0__EMI_EIM_CS0 IOMUX_PAD(0x478, 0x0a0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS1__EMI_EIM_CS1 IOMUX_PAD(0x47c, 0x0a4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS1__EMI_NANDF_CE3 IOMUX_PAD(0x47c, 0x0a4, 3, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS2__EMI_EIM_CS2 IOMUX_PAD(0x480, 0x0a8, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS3__EMI_EIM_CS3 IOMUX_PAD(0x484, 0x0ac, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS4__EMI_EIM_CS4 IOMUX_PAD(0x488, 0x0b0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__EMI_DTACK_B IOMUX_PAD(0x488, 0x0b0, 1, 0x800, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__EMI_NANDF_CE1 IOMUX_PAD(0x488, 0x0b0, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__GPIO1_20 IOMUX_PAD(0x488, 0x0b0, 5, 0x83c, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS5__EMI_EIM_CS5 IOMUX_PAD(0x48c, 0x0b4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__CSPI2_SS2 IOMUX_PAD(0x48c, 0x0b4, 1, 0x7f8, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__CSPI1_SS2 IOMUX_PAD(0x48c, 0x0b4, 2, 0x7d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_CS5__EMI_NANDF_CE2 IOMUX_PAD(0x48c, 0x0b4, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__GPIO1_21 IOMUX_PAD(0x48c, 0x0b4, 5, 0x840, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NF_CE0__EMI_NANDF_CE0 IOMUX_PAD(0x490, 0x0b8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NF_CE0__GPIO1_22 IOMUX_PAD(0x490, 0x0b8, 5, 0x844, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ECB__EMI_EIM_ECB IOMUX_PAD(0x494, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LBA__EMI_EIM_LBA IOMUX_PAD(0x498, 0x0bc, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_BCLK__EMI_EIM_BCLK IOMUX_PAD(0x49c, 0x0c0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RW__EMI_EIM_RW IOMUX_PAD(0x4a0, 0x0c4, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RAS__EMI_DRAM_RAS IOMUX_PAD(0x4a4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CAS__EMI_DRAM_CAS IOMUX_PAD(0x4a8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDWE__EMI_DRAM_SDWE IOMUX_PAD(0x4ac, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCKE0__EMI_DRAM_SDCKE_0 IOMUX_PAD(0x4b0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCKE1__EMI_DRAM_SDCKE_1 IOMUX_PAD(0x4b4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCLK__EMI_DRAM_SDCLK IOMUX_PAD(0x4b8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS0__EMI_DRAM_SDQS_0 IOMUX_PAD(0x4bc, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS1__EMI_DRAM_SDQS_1 IOMUX_PAD(0x4c0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS2__EMI_DRAM_SDQS_2 IOMUX_PAD(0x4c4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS3__EMI_DRAM_SDQS_3 IOMUX_PAD(0x4c8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFWE_B__EMI_NANDF_WE_B IOMUX_PAD(0x4cc, 0x0c8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__USB_TOP_USBH2_DATA_3 IOMUX_PAD(0x4cc, 0x0c8, 1, 0x9d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x4cc, 0x0c8, 2, 0x924, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__GPIO2_18 IOMUX_PAD(0x4cc, 0x0c8, 5, 0x88c, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__ARM11P_TOP_TRACE_0 IOMUX_PAD(0x4cc, 0x0c8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFRE_B__EMI_NANDF_RE_B IOMUX_PAD(0x4d0, 0x0cc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__USB_TOP_USBH2_DIR IOMUX_PAD(0x4d0, 0x0cc, 1, 0x9ec, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__IPU_DISPB_BCLK IOMUX_PAD(0x4d0, 0x0cc, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__GPIO2_19 IOMUX_PAD(0x4d0, 0x0cc, 5, 0x890, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__ARM11P_TOP_TRACE_1 IOMUX_PAD(0x4d0, 0x0cc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFALE__EMI_NANDF_ALE IOMUX_PAD(0x4d4, 0x0d0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__USB_TOP_USBH2_STP IOMUX_PAD(0x4d4, 0x0d0, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__IPU_DISPB_CS0 IOMUX_PAD(0x4d4, 0x0d0, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__GPIO2_20 IOMUX_PAD(0x4d4, 0x0d0, 5, 0x898, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__ARM11P_TOP_TRACE_2 IOMUX_PAD(0x4d4, 0x0d0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFCLE__EMI_NANDF_CLE IOMUX_PAD(0x4d8, 0x0d4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__USB_TOP_USBH2_NXT IOMUX_PAD(0x4d8, 0x0d4, 1, 0x9f0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__IPU_DISPB_PAR_RS IOMUX_PAD(0x4d8, 0x0d4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__GPIO2_21 IOMUX_PAD(0x4d8, 0x0d4, 5, 0x89c, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__ARM11P_TOP_TRACE_3 IOMUX_PAD(0x4d8, 0x0d4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFWP_B__EMI_NANDF_WP_B IOMUX_PAD(0x4dc, 0x0d8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__USB_TOP_USBH2_DATA_7 IOMUX_PAD(0x4dc, 0x0d8, 1, 0x9e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__IPU_DISPB_WR IOMUX_PAD(0x4dc, 0x0d8, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__GPIO2_22 IOMUX_PAD(0x4dc, 0x0d8, 5, 0x8a0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__ARM11P_TOP_TRCTL IOMUX_PAD(0x4dc, 0x0d8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFRB__EMI_NANDF_RB IOMUX_PAD(0x4e0, 0x0dc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__IPU_DISPB_RD IOMUX_PAD(0x4e0, 0x0dc, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__GPIO2_23 IOMUX_PAD(0x4e0, 0x0dc, 5, 0x8a4, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__ARM11P_TOP_TRCLK IOMUX_PAD(0x4e0, 0x0dc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D15__EMI_EIM_D_15 IOMUX_PAD(0x4e4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D14__EMI_EIM_D_14 IOMUX_PAD(0x4e8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D13__EMI_EIM_D_13 IOMUX_PAD(0x4ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D12__EMI_EIM_D_12 IOMUX_PAD(0x4f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D11__EMI_EIM_D_11 IOMUX_PAD(0x4f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D10__EMI_EIM_D_10 IOMUX_PAD(0x4f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D9__EMI_EIM_D_9 IOMUX_PAD(0x4fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D8__EMI_EIM_D_8 IOMUX_PAD(0x500, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D7__EMI_EIM_D_7 IOMUX_PAD(0x504, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D6__EMI_EIM_D_6 IOMUX_PAD(0x508, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D5__EMI_EIM_D_5 IOMUX_PAD(0x50c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D4__EMI_EIM_D_4 IOMUX_PAD(0x510, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3__EMI_EIM_D_3 IOMUX_PAD(0x514, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D2__EMI_EIM_D_2 IOMUX_PAD(0x518, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D1__EMI_EIM_D_1 IOMUX_PAD(0x51c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D0__EMI_EIM_D_0 IOMUX_PAD(0x520, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D8__IPU_CSI_D_8 IOMUX_PAD(0x524, 0x0e0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__KPP_COL_0 IOMUX_PAD(0x524, 0x0e0, 1, 0x950, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__GPIO1_20 IOMUX_PAD(0x524, 0x0e0, 5, 0x83c, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__ARM11P_TOP_EVNTBUS_13 IOMUX_PAD(0x524, 0x0e0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D9__IPU_CSI_D_9 IOMUX_PAD(0x528, 0x0e4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__KPP_COL_1 IOMUX_PAD(0x528, 0x0e4, 1, 0x954, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__GPIO1_21 IOMUX_PAD(0x528, 0x0e4, 5, 0x840, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__ARM11P_TOP_EVNTBUS_14 IOMUX_PAD(0x528, 0x0e4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D10__IPU_CSI_D_10 IOMUX_PAD(0x52c, 0x0e8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__KPP_COL_2 IOMUX_PAD(0x52c, 0x0e8, 1, 0x958, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__GPIO1_22 IOMUX_PAD(0x52c, 0x0e8, 5, 0x844, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__ARM11P_TOP_EVNTBUS_15 IOMUX_PAD(0x52c, 0x0e8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D11__IPU_CSI_D_11 IOMUX_PAD(0x530, 0x0ec, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D11__KPP_COL_3 IOMUX_PAD(0x530, 0x0ec, 1, 0x95c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D11__GPIO1_23 IOMUX_PAD(0x530, 0x0ec, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D12__IPU_CSI_D_12 IOMUX_PAD(0x534, 0x0f0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D12__KPP_ROW_0 IOMUX_PAD(0x534, 0x0f0, 1, 0x970, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D12__GPIO1_24 IOMUX_PAD(0x534, 0x0f0, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D13__IPU_CSI_D_13 IOMUX_PAD(0x538, 0x0f4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D13__KPP_ROW_1 IOMUX_PAD(0x538, 0x0f4, 1, 0x974, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D13__GPIO1_25 IOMUX_PAD(0x538, 0x0f4, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D14__IPU_CSI_D_14 IOMUX_PAD(0x53c, 0x0f8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D14__KPP_ROW_2 IOMUX_PAD(0x53c, 0x0f8, 1, 0x978, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D14__GPIO1_26 IOMUX_PAD(0x53c, 0x0f8, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D15__IPU_CSI_D_15 IOMUX_PAD(0x540, 0x0fc, 0, 0x97c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D15__KPP_ROW_3 IOMUX_PAD(0x540, 0x0fc, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D15__GPIO1_27 IOMUX_PAD(0x540, 0x0fc, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_MCLK__IPU_CSI_MCLK IOMUX_PAD(0x544, 0x100, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_MCLK__GPIO1_28 IOMUX_PAD(0x544, 0x100, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_VSYNC__IPU_CSI_VSYNC IOMUX_PAD(0x548, 0x104, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_VSYNC__GPIO1_29 IOMUX_PAD(0x548, 0x104, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_HSYNC__IPU_CSI_HSYNC IOMUX_PAD(0x54c, 0x108, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_HSYNC__GPIO1_30 IOMUX_PAD(0x54c, 0x108, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_PIXCLK__IPU_CSI_PIXCLK IOMUX_PAD(0x550, 0x10c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_PIXCLK__GPIO1_31 IOMUX_PAD(0x550, 0x10c, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C1_CLK__I2C1_SCL IOMUX_PAD(0x554, 0x110, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_CLK__GPIO2_24 IOMUX_PAD(0x554, 0x110, 5, 0x8a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_CLK__CCM_USB_BYP_CLK IOMUX_PAD(0x554, 0x110, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C1_DAT__I2C1_SDA IOMUX_PAD(0x558, 0x114, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_DAT__GPIO2_25 IOMUX_PAD(0x558, 0x114, 5, 0x8ac, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C2_CLK__I2C2_SCL IOMUX_PAD(0x55c, 0x118, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__CAN1_TXCAN IOMUX_PAD(0x55c, 0x118, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR IOMUX_PAD(0x55c, 0x118, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__GPIO2_26 IOMUX_PAD(0x55c, 0x118, 5, 0x8b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__SDMA_DEBUG_BUS_DEVICE_2 IOMUX_PAD(0x55c, 0x118, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C2_DAT__I2C2_SDA IOMUX_PAD(0x560, 0x11c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__CAN1_RXCAN IOMUX_PAD(0x560, 0x11c, 1, 0x7c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC IOMUX_PAD(0x560, 0x11c, 2, 0x9f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__GPIO2_27 IOMUX_PAD(0x560, 0x11c, 5, 0x8b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__SDMA_DEBUG_BUS_DEVICE_3 IOMUX_PAD(0x560, 0x11c, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXD4__AUDMUX_AUD4_TXD IOMUX_PAD(0x564, 0x120, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD4__GPIO2_28 IOMUX_PAD(0x564, 0x120, 5, 0x8b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD4__ARM11P_TOP_ARM_COREASID0 IOMUX_PAD(0x564, 0x120, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SRXD4__AUDMUX_AUD4_RXD IOMUX_PAD(0x568, 0x124, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD4__GPIO2_29 IOMUX_PAD(0x568, 0x124, 5, 0x8bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD4__ARM11P_TOP_ARM_COREASID1 IOMUX_PAD(0x568, 0x124, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCK4__AUDMUX_AUD4_TXC IOMUX_PAD(0x56c, 0x128, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK4__GPIO2_30 IOMUX_PAD(0x56c, 0x128, 5, 0x8c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK4__ARM11P_TOP_ARM_COREASID2 IOMUX_PAD(0x56c, 0x128, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS IOMUX_PAD(0x570, 0x12c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS4__GPIO2_31 IOMUX_PAD(0x570, 0x12c, 5, 0x8c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS4__ARM11P_TOP_ARM_COREASID3 IOMUX_PAD(0x570, 0x12c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXD5__AUDMUX_AUD5_TXD IOMUX_PAD(0x574, 0x130, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x574, 0x130, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__CSPI2_MOSI IOMUX_PAD(0x574, 0x130, 2, 0x7ec, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__GPIO1_0 IOMUX_PAD(0x574, 0x130, 5, 0x82c, 1, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__ARM11P_TOP_ARM_COREASID4 IOMUX_PAD(0x574, 0x130, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SRXD5__AUDMUX_AUD5_RXD IOMUX_PAD(0x578, 0x134, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__SPDIF_SPDIF_IN1 IOMUX_PAD(0x578, 0x134, 1, 0x998, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__CSPI2_MISO IOMUX_PAD(0x578, 0x134, 2, 0x7e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__GPIO1_1 IOMUX_PAD(0x578, 0x134, 5, 0x838, 1, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__ARM11P_TOP_ARM_COREASID5 IOMUX_PAD(0x578, 0x134, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCK5__AUDMUX_AUD5_TXC IOMUX_PAD(0x57c, 0x138, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x57c, 0x138, 1, 0x994, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__CSPI2_SCLK IOMUX_PAD(0x57c, 0x138, 2, 0x7e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__GPIO1_2 IOMUX_PAD(0x57c, 0x138, 5, 0x848, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__ARM11P_TOP_ARM_COREASID6 IOMUX_PAD(0x57c, 0x138, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXFS5__AUDMUX_AUD5_TXFS IOMUX_PAD(0x580, 0x13c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__CSPI2_RDY IOMUX_PAD(0x580, 0x13c, 2, 0x7e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__GPIO1_3 IOMUX_PAD(0x580, 0x13c, 5, 0x84c, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__ARM11P_TOP_ARM_COREASID7 IOMUX_PAD(0x580, 0x13c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCKR__ESAI_SCKR IOMUX_PAD(0x584, 0x140, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCKR__GPIO1_4 IOMUX_PAD(0x584, 0x140, 5, 0x850, 1, NO_PAD_CTRL)
-#define MX35_PAD_SCKR__ARM11P_TOP_EVNTBUS_10 IOMUX_PAD(0x584, 0x140, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FSR__ESAI_FSR IOMUX_PAD(0x588, 0x144, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FSR__GPIO1_5 IOMUX_PAD(0x588, 0x144, 5, 0x854, 1, NO_PAD_CTRL)
-#define MX35_PAD_FSR__ARM11P_TOP_EVNTBUS_11 IOMUX_PAD(0x588, 0x144, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_HCKR__ESAI_HCKR IOMUX_PAD(0x58c, 0x148, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__AUDMUX_AUD5_RXFS IOMUX_PAD(0x58c, 0x148, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__CSPI2_SS0 IOMUX_PAD(0x58c, 0x148, 2, 0x7f0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__IPU_FLASH_STROBE IOMUX_PAD(0x58c, 0x148, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__GPIO1_6 IOMUX_PAD(0x58c, 0x148, 5, 0x858, 1, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__ARM11P_TOP_EVNTBUS_12 IOMUX_PAD(0x58c, 0x148, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCKT__ESAI_SCKT IOMUX_PAD(0x590, 0x14c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__GPIO1_7 IOMUX_PAD(0x590, 0x14c, 5, 0x85c, 1, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__IPU_CSI_D_0 IOMUX_PAD(0x590, 0x14c, 6, 0x930, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__KPP_ROW_2 IOMUX_PAD(0x590, 0x14c, 7, 0x978, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_FST__ESAI_FST IOMUX_PAD(0x594, 0x150, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FST__GPIO1_8 IOMUX_PAD(0x594, 0x150, 5, 0x860, 1, NO_PAD_CTRL)
-#define MX35_PAD_FST__IPU_CSI_D_1 IOMUX_PAD(0x594, 0x150, 6, 0x934, 0, NO_PAD_CTRL)
-#define MX35_PAD_FST__KPP_ROW_3 IOMUX_PAD(0x594, 0x150, 7, 0x97c, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_HCKT__ESAI_HCKT IOMUX_PAD(0x598, 0x154, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__AUDMUX_AUD5_RXC IOMUX_PAD(0x598, 0x154, 1, 0x7a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__GPIO1_9 IOMUX_PAD(0x598, 0x154, 5, 0x864, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__IPU_CSI_D_2 IOMUX_PAD(0x598, 0x154, 6, 0x938, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__KPP_COL_3 IOMUX_PAD(0x598, 0x154, 7, 0x95c, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX5_RX0__ESAI_TX5_RX0 IOMUX_PAD(0x59c, 0x158, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__AUDMUX_AUD4_RXC IOMUX_PAD(0x59c, 0x158, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__CSPI2_SS2 IOMUX_PAD(0x59c, 0x158, 2, 0x7f8, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__CAN2_TXCAN IOMUX_PAD(0x59c, 0x158, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__UART2_DTR IOMUX_PAD(0x59c, 0x158, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__GPIO1_10 IOMUX_PAD(0x59c, 0x158, 5, 0x830, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__EMI_M3IF_CHOSEN_MASTER_0 IOMUX_PAD(0x59c, 0x158, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TX4_RX1__ESAI_TX4_RX1 IOMUX_PAD(0x5a0, 0x15c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__AUDMUX_AUD4_RXFS IOMUX_PAD(0x5a0, 0x15c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__CSPI2_SS3 IOMUX_PAD(0x5a0, 0x15c, 2, 0x7fc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__CAN2_RXCAN IOMUX_PAD(0x5a0, 0x15c, 3, 0x7cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__UART2_DSR IOMUX_PAD(0x5a0, 0x15c, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__GPIO1_11 IOMUX_PAD(0x5a0, 0x15c, 5, 0x834, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__IPU_CSI_D_3 IOMUX_PAD(0x5a0, 0x15c, 6, 0x93c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__KPP_ROW_0 IOMUX_PAD(0x5a0, 0x15c, 7, 0x970, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX3_RX2__ESAI_TX3_RX2 IOMUX_PAD(0x5a4, 0x160, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__I2C3_SCL IOMUX_PAD(0x5a4, 0x160, 1, 0x91c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__EMI_NANDF_CE1 IOMUX_PAD(0x5a4, 0x160, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__GPIO1_12 IOMUX_PAD(0x5a4, 0x160, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__IPU_CSI_D_4 IOMUX_PAD(0x5a4, 0x160, 6, 0x940, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__KPP_ROW_1 IOMUX_PAD(0x5a4, 0x160, 7, 0x974, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX2_RX3__ESAI_TX2_RX3 IOMUX_PAD(0x5a8, 0x164, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__I2C3_SDA IOMUX_PAD(0x5a8, 0x164, 1, 0x920, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__EMI_NANDF_CE2 IOMUX_PAD(0x5a8, 0x164, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__GPIO1_13 IOMUX_PAD(0x5a8, 0x164, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__IPU_CSI_D_5 IOMUX_PAD(0x5a8, 0x164, 6, 0x944, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__KPP_COL_0 IOMUX_PAD(0x5a8, 0x164, 7, 0x950, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX1__ESAI_TX1 IOMUX_PAD(0x5ac, 0x168, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__CCM_PMIC_RDY IOMUX_PAD(0x5ac, 0x168, 1, 0x7d4, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX1__CSPI1_SS2 IOMUX_PAD(0x5ac, 0x168, 2, 0x7d8, 2, NO_PAD_CTRL)
-#define MX35_PAD_TX1__EMI_NANDF_CE3 IOMUX_PAD(0x5ac, 0x168, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__UART2_RI IOMUX_PAD(0x5ac, 0x168, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__GPIO1_14 IOMUX_PAD(0x5ac, 0x168, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__IPU_CSI_D_6 IOMUX_PAD(0x5ac, 0x168, 6, 0x948, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__KPP_COL_1 IOMUX_PAD(0x5ac, 0x168, 7, 0x954, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX0__ESAI_TX0 IOMUX_PAD(0x5b0, 0x16c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x5b0, 0x16c, 1, 0x994, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX0__CSPI1_SS3 IOMUX_PAD(0x5b0, 0x16c, 2, 0x7dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__EMI_DTACK_B IOMUX_PAD(0x5b0, 0x16c, 3, 0x800, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX0__UART2_DCD IOMUX_PAD(0x5b0, 0x16c, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__GPIO1_15 IOMUX_PAD(0x5b0, 0x16c, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__IPU_CSI_D_7 IOMUX_PAD(0x5b0, 0x16c, 6, 0x94c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__KPP_COL_2 IOMUX_PAD(0x5b0, 0x16c, 7, 0x958, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_MOSI__CSPI1_MOSI IOMUX_PAD(0x5b4, 0x170, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MOSI__GPIO1_16 IOMUX_PAD(0x5b4, 0x170, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MOSI__ECT_CTI_TRIG_OUT1_2 IOMUX_PAD(0x5b4, 0x170, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_MISO__CSPI1_MISO IOMUX_PAD(0x5b8, 0x174, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MISO__GPIO1_17 IOMUX_PAD(0x5b8, 0x174, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MISO__ECT_CTI_TRIG_OUT1_3 IOMUX_PAD(0x5b8, 0x174, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SS0__CSPI1_SS0 IOMUX_PAD(0x5bc, 0x178, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__OWIRE_LINE IOMUX_PAD(0x5bc, 0x178, 1, 0x990, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__CSPI2_SS3 IOMUX_PAD(0x5bc, 0x178, 2, 0x7fc, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__GPIO1_18 IOMUX_PAD(0x5bc, 0x178, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__ECT_CTI_TRIG_OUT1_4 IOMUX_PAD(0x5bc, 0x178, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SS1__CSPI1_SS1 IOMUX_PAD(0x5c0, 0x17c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__PWM_PWMO IOMUX_PAD(0x5c0, 0x17c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__CCM_CLK32K IOMUX_PAD(0x5c0, 0x17c, 2, 0x7d0, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__GPIO1_19 IOMUX_PAD(0x5c0, 0x17c, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__IPU_DIAGB_29 IOMUX_PAD(0x5c0, 0x17c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__ECT_CTI_TRIG_OUT1_5 IOMUX_PAD(0x5c0, 0x17c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SCLK__CSPI1_SCLK IOMUX_PAD(0x5c4, 0x180, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__GPIO3_4 IOMUX_PAD(0x5c4, 0x180, 5, 0x904, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__IPU_DIAGB_30 IOMUX_PAD(0x5c4, 0x180, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__EMI_M3IF_CHOSEN_MASTER_1 IOMUX_PAD(0x5c4, 0x180, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SPI_RDY__CSPI1_RDY IOMUX_PAD(0x5c8, 0x184, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__GPIO3_5 IOMUX_PAD(0x5c8, 0x184, 5, 0x908, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__IPU_DIAGB_31 IOMUX_PAD(0x5c8, 0x184, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__EMI_M3IF_CHOSEN_MASTER_2 IOMUX_PAD(0x5c8, 0x184, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RXD1__UART1_RXD_MUX IOMUX_PAD(0x5cc, 0x188, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__CSPI2_MOSI IOMUX_PAD(0x5cc, 0x188, 1, 0x7ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__KPP_COL_4 IOMUX_PAD(0x5cc, 0x188, 4, 0x960, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__GPIO3_6 IOMUX_PAD(0x5cc, 0x188, 5, 0x90c, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__ARM11P_TOP_EVNTBUS_16 IOMUX_PAD(0x5cc, 0x188, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TXD1__UART1_TXD_MUX IOMUX_PAD(0x5d0, 0x18c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__CSPI2_MISO IOMUX_PAD(0x5d0, 0x18c, 1, 0x7e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__KPP_COL_5 IOMUX_PAD(0x5d0, 0x18c, 4, 0x964, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__GPIO3_7 IOMUX_PAD(0x5d0, 0x18c, 5, 0x910, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__ARM11P_TOP_EVNTBUS_17 IOMUX_PAD(0x5d0, 0x18c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTS1__UART1_RTS IOMUX_PAD(0x5d4, 0x190, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__CSPI2_SCLK IOMUX_PAD(0x5d4, 0x190, 1, 0x7e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__I2C3_SCL IOMUX_PAD(0x5d4, 0x190, 2, 0x91c, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__IPU_CSI_D_0 IOMUX_PAD(0x5d4, 0x190, 3, 0x930, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__KPP_COL_6 IOMUX_PAD(0x5d4, 0x190, 4, 0x968, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__GPIO3_8 IOMUX_PAD(0x5d4, 0x190, 5, 0x914, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__EMI_NANDF_CE1 IOMUX_PAD(0x5d4, 0x190, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__ARM11P_TOP_EVNTBUS_18 IOMUX_PAD(0x5d4, 0x190, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CTS1__UART1_CTS IOMUX_PAD(0x5d8, 0x194, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__CSPI2_RDY IOMUX_PAD(0x5d8, 0x194, 1, 0x7e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__I2C3_SDA IOMUX_PAD(0x5d8, 0x194, 2, 0x920, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__IPU_CSI_D_1 IOMUX_PAD(0x5d8, 0x194, 3, 0x934, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__KPP_COL_7 IOMUX_PAD(0x5d8, 0x194, 4, 0x96c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__GPIO3_9 IOMUX_PAD(0x5d8, 0x194, 5, 0x918, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__EMI_NANDF_CE2 IOMUX_PAD(0x5d8, 0x194, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__ARM11P_TOP_EVNTBUS_19 IOMUX_PAD(0x5d8, 0x194, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RXD2__UART2_RXD_MUX IOMUX_PAD(0x5dc, 0x198, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD2__KPP_ROW_4 IOMUX_PAD(0x5dc, 0x198, 4, 0x980, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD2__GPIO3_10 IOMUX_PAD(0x5dc, 0x198, 5, 0x8ec, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TXD2__UART2_TXD_MUX IOMUX_PAD(0x5e0, 0x19c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x5e0, 0x19c, 1, 0x994, 2, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__KPP_ROW_5 IOMUX_PAD(0x5e0, 0x19c, 4, 0x984, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__GPIO3_11 IOMUX_PAD(0x5e0, 0x19c, 5, 0x8f0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTS2__UART2_RTS IOMUX_PAD(0x5e4, 0x1a0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__SPDIF_SPDIF_IN1 IOMUX_PAD(0x5e4, 0x1a0, 1, 0x998, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__CAN2_RXCAN IOMUX_PAD(0x5e4, 0x1a0, 2, 0x7cc, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__IPU_CSI_D_2 IOMUX_PAD(0x5e4, 0x1a0, 3, 0x938, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__KPP_ROW_6 IOMUX_PAD(0x5e4, 0x1a0, 4, 0x988, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__GPIO3_12 IOMUX_PAD(0x5e4, 0x1a0, 5, 0x8f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__AUDMUX_AUD5_RXC IOMUX_PAD(0x5e4, 0x1a0, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__UART3_RXD_MUX IOMUX_PAD(0x5e4, 0x1a0, 7, 0x9a0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CTS2__UART2_CTS IOMUX_PAD(0x5e8, 0x1a4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x5e8, 0x1a4, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__CAN2_TXCAN IOMUX_PAD(0x5e8, 0x1a4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__IPU_CSI_D_3 IOMUX_PAD(0x5e8, 0x1a4, 3, 0x93c, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__KPP_ROW_7 IOMUX_PAD(0x5e8, 0x1a4, 4, 0x98c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__GPIO3_13 IOMUX_PAD(0x5e8, 0x1a4, 5, 0x8f8, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__AUDMUX_AUD5_RXFS IOMUX_PAD(0x5e8, 0x1a4, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__UART3_TXD_MUX IOMUX_PAD(0x5e8, 0x1a4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTCK__ARM11P_TOP_RTCK IOMUX_PAD(0x5ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TCK__SJC_TCK IOMUX_PAD(0x5f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TMS__SJC_TMS IOMUX_PAD(0x5f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TDI__SJC_TDI IOMUX_PAD(0x5f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TDO__SJC_TDO IOMUX_PAD(0x5fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TRSTB__SJC_TRSTB IOMUX_PAD(0x600, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_DE_B__SJC_DE_B IOMUX_PAD(0x604, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SJC_MOD__SJC_MOD IOMUX_PAD(0x608, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR IOMUX_PAD(0x60c, 0x1a8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_PWR__USB_TOP_USBH2_PWR IOMUX_PAD(0x60c, 0x1a8, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_PWR__GPIO3_14 IOMUX_PAD(0x60c, 0x1a8, 5, 0x8fc, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC IOMUX_PAD(0x610, 0x1ac, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_OC__USB_TOP_USBH2_OC IOMUX_PAD(0x610, 0x1ac, 1, 0x9f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_OC__GPIO3_15 IOMUX_PAD(0x610, 0x1ac, 5, 0x900, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD0__IPU_DISPB_DAT_0 IOMUX_PAD(0x614, 0x1b0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD0__GPIO2_0 IOMUX_PAD(0x614, 0x1b0, 5, 0x868, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD0__SDMA_SDMA_DEBUG_PC_0 IOMUX_PAD(0x614, 0x1b0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD1__IPU_DISPB_DAT_1 IOMUX_PAD(0x618, 0x1b4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD1__GPIO2_1 IOMUX_PAD(0x618, 0x1b4, 5, 0x894, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD1__SDMA_SDMA_DEBUG_PC_1 IOMUX_PAD(0x618, 0x1b4, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD2__IPU_DISPB_DAT_2 IOMUX_PAD(0x61c, 0x1b8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD2__GPIO2_2 IOMUX_PAD(0x61c, 0x1b8, 5, 0x8c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD2__SDMA_SDMA_DEBUG_PC_2 IOMUX_PAD(0x61c, 0x1b8, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD3__IPU_DISPB_DAT_3 IOMUX_PAD(0x620, 0x1bc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD3__GPIO2_3 IOMUX_PAD(0x620, 0x1bc, 5, 0x8cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD3__SDMA_SDMA_DEBUG_PC_3 IOMUX_PAD(0x620, 0x1bc, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD4__IPU_DISPB_DAT_4 IOMUX_PAD(0x624, 0x1c0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD4__GPIO2_4 IOMUX_PAD(0x624, 0x1c0, 5, 0x8d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD4__SDMA_SDMA_DEBUG_PC_4 IOMUX_PAD(0x624, 0x1c0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD5__IPU_DISPB_DAT_5 IOMUX_PAD(0x628, 0x1c4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD5__GPIO2_5 IOMUX_PAD(0x628, 0x1c4, 5, 0x8d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD5__SDMA_SDMA_DEBUG_PC_5 IOMUX_PAD(0x628, 0x1c4, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD6__IPU_DISPB_DAT_6 IOMUX_PAD(0x62c, 0x1c8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD6__GPIO2_6 IOMUX_PAD(0x62c, 0x1c8, 5, 0x8d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD6__SDMA_SDMA_DEBUG_PC_6 IOMUX_PAD(0x62c, 0x1c8, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD7__IPU_DISPB_DAT_7 IOMUX_PAD(0x630, 0x1cc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD7__GPIO2_7 IOMUX_PAD(0x630, 0x1cc, 5, 0x8dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD7__SDMA_SDMA_DEBUG_PC_7 IOMUX_PAD(0x630, 0x1cc, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD8__IPU_DISPB_DAT_8 IOMUX_PAD(0x634, 0x1d0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD8__GPIO2_8 IOMUX_PAD(0x634, 0x1d0, 5, 0x8e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD8__SDMA_SDMA_DEBUG_PC_8 IOMUX_PAD(0x634, 0x1d0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD9__IPU_DISPB_DAT_9 IOMUX_PAD(0x638, 0x1d4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD9__GPIO2_9 IOMUX_PAD(0x638, 0x1d4, 5, 0x8e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD9__SDMA_SDMA_DEBUG_PC_9 IOMUX_PAD(0x638, 0x1d4, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD10__IPU_DISPB_DAT_10 IOMUX_PAD(0x63c, 0x1d8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD10__GPIO2_10 IOMUX_PAD(0x63c, 0x1d8, 5, 0x86c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD10__SDMA_SDMA_DEBUG_PC_10 IOMUX_PAD(0x63c, 0x1d8, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD11__IPU_DISPB_DAT_11 IOMUX_PAD(0x640, 0x1dc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__GPIO2_11 IOMUX_PAD(0x640, 0x1dc, 5, 0x870, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__SDMA_SDMA_DEBUG_PC_11 IOMUX_PAD(0x640, 0x1dc, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__ARM11P_TOP_TRACE_4 IOMUX_PAD(0x640, 0x1dc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD12__IPU_DISPB_DAT_12 IOMUX_PAD(0x644, 0x1e0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__GPIO2_12 IOMUX_PAD(0x644, 0x1e0, 5, 0x874, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__SDMA_SDMA_DEBUG_PC_12 IOMUX_PAD(0x644, 0x1e0, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__ARM11P_TOP_TRACE_5 IOMUX_PAD(0x644, 0x1e0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD13__IPU_DISPB_DAT_13 IOMUX_PAD(0x648, 0x1e4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__GPIO2_13 IOMUX_PAD(0x648, 0x1e4, 5, 0x878, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__SDMA_SDMA_DEBUG_PC_13 IOMUX_PAD(0x648, 0x1e4, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__ARM11P_TOP_TRACE_6 IOMUX_PAD(0x648, 0x1e4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD14__IPU_DISPB_DAT_14 IOMUX_PAD(0x64c, 0x1e8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__GPIO2_14 IOMUX_PAD(0x64c, 0x1e8, 5, 0x87c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__SDMA_SDMA_DEBUG_EVENT_CHANNEL_0 IOMUX_PAD(0x64c, 0x1e8, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__ARM11P_TOP_TRACE_7 IOMUX_PAD(0x64c, 0x1e8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD15__IPU_DISPB_DAT_15 IOMUX_PAD(0x650, 0x1ec, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__GPIO2_15 IOMUX_PAD(0x650, 0x1ec, 5, 0x880, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__SDMA_SDMA_DEBUG_EVENT_CHANNEL_1 IOMUX_PAD(0x650, 0x1ec, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__ARM11P_TOP_TRACE_8 IOMUX_PAD(0x650, 0x1ec, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD16__IPU_DISPB_DAT_16 IOMUX_PAD(0x654, 0x1f0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x654, 0x1f0, 2, 0x928, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__GPIO2_16 IOMUX_PAD(0x654, 0x1f0, 5, 0x884, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__SDMA_SDMA_DEBUG_EVENT_CHANNEL_2 IOMUX_PAD(0x654, 0x1f0, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__ARM11P_TOP_TRACE_9 IOMUX_PAD(0x654, 0x1f0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD17__IPU_DISPB_DAT_17 IOMUX_PAD(0x658, 0x1f4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__IPU_DISPB_CS2 IOMUX_PAD(0x658, 0x1f4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__GPIO2_17 IOMUX_PAD(0x658, 0x1f4, 5, 0x888, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__SDMA_SDMA_DEBUG_EVENT_CHANNEL_3 IOMUX_PAD(0x658, 0x1f4, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__ARM11P_TOP_TRACE_10 IOMUX_PAD(0x658, 0x1f4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD18__IPU_DISPB_DAT_18 IOMUX_PAD(0x65c, 0x1f8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x65c, 0x1f8, 1, 0x924, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD18__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x65c, 0x1f8, 2, 0x928, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD18__ESDHC3_CMD IOMUX_PAD(0x65c, 0x1f8, 3, 0x818, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__USB_TOP_USBOTG_DATA_3 IOMUX_PAD(0x65c, 0x1f8, 4, 0x9b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__GPIO3_24 IOMUX_PAD(0x65c, 0x1f8, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__SDMA_SDMA_DEBUG_EVENT_CHANNEL_4 IOMUX_PAD(0x65c, 0x1f8, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__ARM11P_TOP_TRACE_11 IOMUX_PAD(0x65c, 0x1f8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD19__IPU_DISPB_DAT_19 IOMUX_PAD(0x660, 0x1fc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__IPU_DISPB_BCLK IOMUX_PAD(0x660, 0x1fc, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__IPU_DISPB_CS1 IOMUX_PAD(0x660, 0x1fc, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__ESDHC3_CLK IOMUX_PAD(0x660, 0x1fc, 3, 0x814, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__USB_TOP_USBOTG_DIR IOMUX_PAD(0x660, 0x1fc, 4, 0x9c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__GPIO3_25 IOMUX_PAD(0x660, 0x1fc, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__SDMA_SDMA_DEBUG_EVENT_CHANNEL_5 IOMUX_PAD(0x660, 0x1fc, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__ARM11P_TOP_TRACE_12 IOMUX_PAD(0x660, 0x1fc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD20__IPU_DISPB_DAT_20 IOMUX_PAD(0x664, 0x200, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__IPU_DISPB_CS0 IOMUX_PAD(0x664, 0x200, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__IPU_DISPB_SD_CLK IOMUX_PAD(0x664, 0x200, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__ESDHC3_DAT0 IOMUX_PAD(0x664, 0x200, 3, 0x81c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__GPIO3_26 IOMUX_PAD(0x664, 0x200, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__SDMA_SDMA_DEBUG_CORE_STATUS_3 IOMUX_PAD(0x664, 0x200, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__ARM11P_TOP_TRACE_13 IOMUX_PAD(0x664, 0x200, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD21__IPU_DISPB_DAT_21 IOMUX_PAD(0x668, 0x204, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__IPU_DISPB_PAR_RS IOMUX_PAD(0x668, 0x204, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__IPU_DISPB_SER_RS IOMUX_PAD(0x668, 0x204, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__ESDHC3_DAT1 IOMUX_PAD(0x668, 0x204, 3, 0x820, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__USB_TOP_USBOTG_STP IOMUX_PAD(0x668, 0x204, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__GPIO3_27 IOMUX_PAD(0x668, 0x204, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__SDMA_DEBUG_EVENT_CHANNEL_SEL IOMUX_PAD(0x668, 0x204, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__ARM11P_TOP_TRACE_14 IOMUX_PAD(0x668, 0x204, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD22__IPU_DISPB_DAT_22 IOMUX_PAD(0x66c, 0x208, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__IPU_DISPB_WR IOMUX_PAD(0x66c, 0x208, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__IPU_DISPB_SD_D_I IOMUX_PAD(0x66c, 0x208, 2, 0x92c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__ESDHC3_DAT2 IOMUX_PAD(0x66c, 0x208, 3, 0x824, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__USB_TOP_USBOTG_NXT IOMUX_PAD(0x66c, 0x208, 4, 0x9c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__GPIO3_28 IOMUX_PAD(0x66c, 0x208, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__SDMA_DEBUG_BUS_ERROR IOMUX_PAD(0x66c, 0x208, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__ARM11P_TOP_TRCTL IOMUX_PAD(0x66c, 0x208, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD23__IPU_DISPB_DAT_23 IOMUX_PAD(0x670, 0x20c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__IPU_DISPB_RD IOMUX_PAD(0x670, 0x20c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__IPU_DISPB_SD_D_IO IOMUX_PAD(0x670, 0x20c, 2, 0x92c, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD23__ESDHC3_DAT3 IOMUX_PAD(0x670, 0x20c, 3, 0x828, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__USB_TOP_USBOTG_DATA_7 IOMUX_PAD(0x670, 0x20c, 4, 0x9c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__GPIO3_29 IOMUX_PAD(0x670, 0x20c, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__SDMA_DEBUG_MATCHED_DMBUS IOMUX_PAD(0x670, 0x20c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__ARM11P_TOP_TRCLK IOMUX_PAD(0x670, 0x20c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC IOMUX_PAD(0x674, 0x210, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__IPU_DISPB_SD_D_IO IOMUX_PAD(0x674, 0x210, 2, 0x92c, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__GPIO3_30 IOMUX_PAD(0x674, 0x210, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__SDMA_DEBUG_RTBUFFER_WRITE IOMUX_PAD(0x674, 0x210, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__ARM11P_TOP_TRACE_15 IOMUX_PAD(0x674, 0x210, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK IOMUX_PAD(0x678, 0x214, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_SD_CLK IOMUX_PAD(0x678, 0x214, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__GPIO3_31 IOMUX_PAD(0x678, 0x214, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__SDMA_SDMA_DEBUG_CORE_STATUS_0 IOMUX_PAD(0x678, 0x214, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__ARM11P_TOP_TRACE_16 IOMUX_PAD(0x678, 0x214, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY IOMUX_PAD(0x67c, 0x218, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__IPU_DISPB_SD_D_O IOMUX_PAD(0x67c, 0x218, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__GPIO1_0 IOMUX_PAD(0x67c, 0x218, 5, 0x82c, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__SDMA_SDMA_DEBUG_CORE_STATUS_1 IOMUX_PAD(0x67c, 0x218, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__ARM11P_TOP_TRACE_17 IOMUX_PAD(0x67c, 0x218, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CONTRAST__IPU_DISPB_CONTR IOMUX_PAD(0x680, 0x21c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__GPIO1_1 IOMUX_PAD(0x680, 0x21c, 5, 0x838, 2, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__SDMA_SDMA_DEBUG_CORE_STATUS_2 IOMUX_PAD(0x680, 0x21c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__ARM11P_TOP_TRACE_18 IOMUX_PAD(0x680, 0x21c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC IOMUX_PAD(0x684, 0x220, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__IPU_DISPB_CS1 IOMUX_PAD(0x684, 0x220, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__GPIO1_2 IOMUX_PAD(0x684, 0x220, 5, 0x848, 1, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__SDMA_DEBUG_YIELD IOMUX_PAD(0x684, 0x220, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__ARM11P_TOP_TRACE_19 IOMUX_PAD(0x684, 0x220, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_REV__IPU_DISPB_D3_REV IOMUX_PAD(0x688, 0x224, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__IPU_DISPB_SER_RS IOMUX_PAD(0x688, 0x224, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__GPIO1_3 IOMUX_PAD(0x688, 0x224, 5, 0x84c, 1, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__SDMA_DEBUG_BUS_RWB IOMUX_PAD(0x688, 0x224, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__ARM11P_TOP_TRACE_20 IOMUX_PAD(0x688, 0x224, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS IOMUX_PAD(0x68c, 0x228, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__IPU_DISPB_CS2 IOMUX_PAD(0x68c, 0x228, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__GPIO1_4 IOMUX_PAD(0x68c, 0x228, 5, 0x850, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__SDMA_DEBUG_BUS_DEVICE_0 IOMUX_PAD(0x68c, 0x228, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__ARM11P_TOP_TRACE_21 IOMUX_PAD(0x68c, 0x228, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_SPL__IPU_DISPB_D3_SPL IOMUX_PAD(0x690, 0x22c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x690, 0x22c, 2, 0x928, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__GPIO1_5 IOMUX_PAD(0x690, 0x22c, 5, 0x854, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__SDMA_DEBUG_BUS_DEVICE_1 IOMUX_PAD(0x690, 0x22c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__ARM11P_TOP_TRACE_22 IOMUX_PAD(0x690, 0x22c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_CMD__ESDHC1_CMD IOMUX_PAD(0x694, 0x230, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__MSHC_SCLK IOMUX_PAD(0x694, 0x230, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x694, 0x230, 3, 0x924, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__USB_TOP_USBOTG_DATA_4 IOMUX_PAD(0x694, 0x230, 4, 0x9b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__GPIO1_6 IOMUX_PAD(0x694, 0x230, 5, 0x858, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__ARM11P_TOP_TRCTL IOMUX_PAD(0x694, 0x230, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_CLK__ESDHC1_CLK IOMUX_PAD(0x698, 0x234, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__MSHC_BS IOMUX_PAD(0x698, 0x234, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__IPU_DISPB_BCLK IOMUX_PAD(0x698, 0x234, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__USB_TOP_USBOTG_DATA_5 IOMUX_PAD(0x698, 0x234, 4, 0x9b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__GPIO1_7 IOMUX_PAD(0x698, 0x234, 5, 0x85c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__ARM11P_TOP_TRCLK IOMUX_PAD(0x698, 0x234, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA0__ESDHC1_DAT0 IOMUX_PAD(0x69c, 0x238, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__MSHC_DATA_0 IOMUX_PAD(0x69c, 0x238, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__IPU_DISPB_CS0 IOMUX_PAD(0x69c, 0x238, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__USB_TOP_USBOTG_DATA_6 IOMUX_PAD(0x69c, 0x238, 4, 0x9bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__GPIO1_8 IOMUX_PAD(0x69c, 0x238, 5, 0x860, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__ARM11P_TOP_TRACE_23 IOMUX_PAD(0x69c, 0x238, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA1__ESDHC1_DAT1 IOMUX_PAD(0x6a0, 0x23c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__MSHC_DATA_1 IOMUX_PAD(0x6a0, 0x23c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__IPU_DISPB_PAR_RS IOMUX_PAD(0x6a0, 0x23c, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__USB_TOP_USBOTG_DATA_0 IOMUX_PAD(0x6a0, 0x23c, 4, 0x9a4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__GPIO1_9 IOMUX_PAD(0x6a0, 0x23c, 5, 0x864, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__ARM11P_TOP_TRACE_24 IOMUX_PAD(0x6a0, 0x23c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA2__ESDHC1_DAT2 IOMUX_PAD(0x6a4, 0x240, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__MSHC_DATA_2 IOMUX_PAD(0x6a4, 0x240, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__IPU_DISPB_WR IOMUX_PAD(0x6a4, 0x240, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__USB_TOP_USBOTG_DATA_1 IOMUX_PAD(0x6a4, 0x240, 4, 0x9a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__GPIO1_10 IOMUX_PAD(0x6a4, 0x240, 5, 0x830, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__ARM11P_TOP_TRACE_25 IOMUX_PAD(0x6a4, 0x240, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA3__ESDHC1_DAT3 IOMUX_PAD(0x6a8, 0x244, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__MSHC_DATA_3 IOMUX_PAD(0x6a8, 0x244, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__IPU_DISPB_RD IOMUX_PAD(0x6a8, 0x244, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__USB_TOP_USBOTG_DATA_2 IOMUX_PAD(0x6a8, 0x244, 4, 0x9ac, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__GPIO1_11 IOMUX_PAD(0x6a8, 0x244, 5, 0x834, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__ARM11P_TOP_TRACE_26 IOMUX_PAD(0x6a8, 0x244, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_CMD__ESDHC2_CMD IOMUX_PAD(0x6ac, 0x248, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__I2C3_SCL IOMUX_PAD(0x6ac, 0x248, 1, 0x91c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__ESDHC1_DAT4 IOMUX_PAD(0x6ac, 0x248, 2, 0x804, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__IPU_CSI_D_2 IOMUX_PAD(0x6ac, 0x248, 3, 0x938, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__USB_TOP_USBH2_DATA_4 IOMUX_PAD(0x6ac, 0x248, 4, 0x9dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__GPIO2_0 IOMUX_PAD(0x6ac, 0x248, 5, 0x868, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x6ac, 0x248, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x6ac, 0x248, 7, 0x928, 3, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_CLK__ESDHC2_CLK IOMUX_PAD(0x6b0, 0x24c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__I2C3_SDA IOMUX_PAD(0x6b0, 0x24c, 1, 0x920, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__ESDHC1_DAT5 IOMUX_PAD(0x6b0, 0x24c, 2, 0x808, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__IPU_CSI_D_3 IOMUX_PAD(0x6b0, 0x24c, 3, 0x93c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__USB_TOP_USBH2_DATA_5 IOMUX_PAD(0x6b0, 0x24c, 4, 0x9e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__GPIO2_1 IOMUX_PAD(0x6b0, 0x24c, 5, 0x894, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__SPDIF_SPDIF_IN1 IOMUX_PAD(0x6b0, 0x24c, 6, 0x998, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__IPU_DISPB_CS2 IOMUX_PAD(0x6b0, 0x24c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA0__ESDHC2_DAT0 IOMUX_PAD(0x6b4, 0x250, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__UART3_RXD_MUX IOMUX_PAD(0x6b4, 0x250, 1, 0x9a0, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__ESDHC1_DAT6 IOMUX_PAD(0x6b4, 0x250, 2, 0x80c, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__IPU_CSI_D_4 IOMUX_PAD(0x6b4, 0x250, 3, 0x940, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__USB_TOP_USBH2_DATA_6 IOMUX_PAD(0x6b4, 0x250, 4, 0x9e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__GPIO2_2 IOMUX_PAD(0x6b4, 0x250, 5, 0x8c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x6b4, 0x250, 6, 0x994, 3, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA1__ESDHC2_DAT1 IOMUX_PAD(0x6b8, 0x254, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__UART3_TXD_MUX IOMUX_PAD(0x6b8, 0x254, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__ESDHC1_DAT7 IOMUX_PAD(0x6b8, 0x254, 2, 0x810, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__IPU_CSI_D_5 IOMUX_PAD(0x6b8, 0x254, 3, 0x944, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__USB_TOP_USBH2_DATA_0 IOMUX_PAD(0x6b8, 0x254, 4, 0x9cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__GPIO2_3 IOMUX_PAD(0x6b8, 0x254, 5, 0x8cc, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA2__ESDHC2_DAT2 IOMUX_PAD(0x6bc, 0x258, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__UART3_RTS IOMUX_PAD(0x6bc, 0x258, 1, 0x99c, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__CAN1_RXCAN IOMUX_PAD(0x6bc, 0x258, 2, 0x7c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__IPU_CSI_D_6 IOMUX_PAD(0x6bc, 0x258, 3, 0x948, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__USB_TOP_USBH2_DATA_1 IOMUX_PAD(0x6bc, 0x258, 4, 0x9d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__GPIO2_4 IOMUX_PAD(0x6bc, 0x258, 5, 0x8d0, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA3__ESDHC2_DAT3 IOMUX_PAD(0x6c0, 0x25c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__UART3_CTS IOMUX_PAD(0x6c0, 0x25c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__CAN1_TXCAN IOMUX_PAD(0x6c0, 0x25c, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__IPU_CSI_D_7 IOMUX_PAD(0x6c0, 0x25c, 3, 0x94c, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__USB_TOP_USBH2_DATA_2 IOMUX_PAD(0x6c0, 0x25c, 4, 0x9d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__GPIO2_5 IOMUX_PAD(0x6c0, 0x25c, 5, 0x8d4, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_CS0__ATA_CS0 IOMUX_PAD(0x6c4, 0x260, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__CSPI1_SS3 IOMUX_PAD(0x6c4, 0x260, 1, 0x7dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__IPU_DISPB_CS1 IOMUX_PAD(0x6c4, 0x260, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__GPIO2_6 IOMUX_PAD(0x6c4, 0x260, 5, 0x8d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__IPU_DIAGB_0 IOMUX_PAD(0x6c4, 0x260, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__ARM11P_TOP_MAX1_HMASTER_0 IOMUX_PAD(0x6c4, 0x260, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_CS1__ATA_CS1 IOMUX_PAD(0x6c8, 0x264, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__IPU_DISPB_CS2 IOMUX_PAD(0x6c8, 0x264, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__CSPI2_SS0 IOMUX_PAD(0x6c8, 0x264, 4, 0x7f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__GPIO2_7 IOMUX_PAD(0x6c8, 0x264, 5, 0x8dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__IPU_DIAGB_1 IOMUX_PAD(0x6c8, 0x264, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__ARM11P_TOP_MAX1_HMASTER_1 IOMUX_PAD(0x6c8, 0x264, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DIOR__ATA_DIOR IOMUX_PAD(0x6cc, 0x268, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__ESDHC3_DAT0 IOMUX_PAD(0x6cc, 0x268, 1, 0x81c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__USB_TOP_USBOTG_DIR IOMUX_PAD(0x6cc, 0x268, 2, 0x9c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__IPU_DISPB_BE0 IOMUX_PAD(0x6cc, 0x268, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__CSPI2_SS1 IOMUX_PAD(0x6cc, 0x268, 4, 0x7f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__GPIO2_8 IOMUX_PAD(0x6cc, 0x268, 5, 0x8e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__IPU_DIAGB_2 IOMUX_PAD(0x6cc, 0x268, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__ARM11P_TOP_MAX1_HMASTER_2 IOMUX_PAD(0x6cc, 0x268, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DIOW__ATA_DIOW IOMUX_PAD(0x6d0, 0x26c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__ESDHC3_DAT1 IOMUX_PAD(0x6d0, 0x26c, 1, 0x820, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__USB_TOP_USBOTG_STP IOMUX_PAD(0x6d0, 0x26c, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__IPU_DISPB_BE1 IOMUX_PAD(0x6d0, 0x26c, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__CSPI2_MOSI IOMUX_PAD(0x6d0, 0x26c, 4, 0x7ec, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__GPIO2_9 IOMUX_PAD(0x6d0, 0x26c, 5, 0x8e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__IPU_DIAGB_3 IOMUX_PAD(0x6d0, 0x26c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__ARM11P_TOP_MAX1_HMASTER_3 IOMUX_PAD(0x6d0, 0x26c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DMACK__ATA_DMACK IOMUX_PAD(0x6d4, 0x270, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__ESDHC3_DAT2 IOMUX_PAD(0x6d4, 0x270, 1, 0x824, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__USB_TOP_USBOTG_NXT IOMUX_PAD(0x6d4, 0x270, 2, 0x9c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__CSPI2_MISO IOMUX_PAD(0x6d4, 0x270, 4, 0x7e8, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__GPIO2_10 IOMUX_PAD(0x6d4, 0x270, 5, 0x86c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__IPU_DIAGB_4 IOMUX_PAD(0x6d4, 0x270, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__ARM11P_TOP_MAX0_HMASTER_0 IOMUX_PAD(0x6d4, 0x270, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_RESET_B__ATA_RESET_B IOMUX_PAD(0x6d8, 0x274, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__ESDHC3_DAT3 IOMUX_PAD(0x6d8, 0x274, 1, 0x828, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__USB_TOP_USBOTG_DATA_0 IOMUX_PAD(0x6d8, 0x274, 2, 0x9a4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__IPU_DISPB_SD_D_O IOMUX_PAD(0x6d8, 0x274, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__CSPI2_RDY IOMUX_PAD(0x6d8, 0x274, 4, 0x7e4, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__GPIO2_11 IOMUX_PAD(0x6d8, 0x274, 5, 0x870, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__IPU_DIAGB_5 IOMUX_PAD(0x6d8, 0x274, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__ARM11P_TOP_MAX0_HMASTER_1 IOMUX_PAD(0x6d8, 0x274, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_IORDY__ATA_IORDY IOMUX_PAD(0x6dc, 0x278, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ESDHC3_DAT4 IOMUX_PAD(0x6dc, 0x278, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__USB_TOP_USBOTG_DATA_1 IOMUX_PAD(0x6dc, 0x278, 2, 0x9a8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__IPU_DISPB_SD_D_IO IOMUX_PAD(0x6dc, 0x278, 3, 0x92c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ESDHC2_DAT4 IOMUX_PAD(0x6dc, 0x278, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__GPIO2_12 IOMUX_PAD(0x6dc, 0x278, 5, 0x874, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__IPU_DIAGB_6 IOMUX_PAD(0x6dc, 0x278, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ARM11P_TOP_MAX0_HMASTER_2 IOMUX_PAD(0x6dc, 0x278, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA0__ATA_DATA_0 IOMUX_PAD(0x6e0, 0x27c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ESDHC3_DAT5 IOMUX_PAD(0x6e0, 0x27c, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__USB_TOP_USBOTG_DATA_2 IOMUX_PAD(0x6e0, 0x27c, 2, 0x9ac, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x6e0, 0x27c, 3, 0x928, 4, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ESDHC2_DAT5 IOMUX_PAD(0x6e0, 0x27c, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__GPIO2_13 IOMUX_PAD(0x6e0, 0x27c, 5, 0x878, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__IPU_DIAGB_7 IOMUX_PAD(0x6e0, 0x27c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ARM11P_TOP_MAX0_HMASTER_3 IOMUX_PAD(0x6e0, 0x27c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA1__ATA_DATA_1 IOMUX_PAD(0x6e4, 0x280, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ESDHC3_DAT6 IOMUX_PAD(0x6e4, 0x280, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__USB_TOP_USBOTG_DATA_3 IOMUX_PAD(0x6e4, 0x280, 2, 0x9b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__IPU_DISPB_SD_CLK IOMUX_PAD(0x6e4, 0x280, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ESDHC2_DAT6 IOMUX_PAD(0x6e4, 0x280, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__GPIO2_14 IOMUX_PAD(0x6e4, 0x280, 5, 0x87c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__IPU_DIAGB_8 IOMUX_PAD(0x6e4, 0x280, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ARM11P_TOP_TRACE_27 IOMUX_PAD(0x6e4, 0x280, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA2__ATA_DATA_2 IOMUX_PAD(0x6e8, 0x284, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ESDHC3_DAT7 IOMUX_PAD(0x6e8, 0x284, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__USB_TOP_USBOTG_DATA_4 IOMUX_PAD(0x6e8, 0x284, 2, 0x9b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__IPU_DISPB_SER_RS IOMUX_PAD(0x6e8, 0x284, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ESDHC2_DAT7 IOMUX_PAD(0x6e8, 0x284, 4, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__GPIO2_15 IOMUX_PAD(0x6e8, 0x284, 5, 0x880, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__IPU_DIAGB_9 IOMUX_PAD(0x6e8, 0x284, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ARM11P_TOP_TRACE_28 IOMUX_PAD(0x6e8, 0x284, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA3__ATA_DATA_3 IOMUX_PAD(0x6ec, 0x288, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__ESDHC3_CLK IOMUX_PAD(0x6ec, 0x288, 1, 0x814, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__USB_TOP_USBOTG_DATA_5 IOMUX_PAD(0x6ec, 0x288, 2, 0x9b8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__CSPI2_SCLK IOMUX_PAD(0x6ec, 0x288, 4, 0x7e0, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__GPIO2_16 IOMUX_PAD(0x6ec, 0x288, 5, 0x884, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__IPU_DIAGB_10 IOMUX_PAD(0x6ec, 0x288, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__ARM11P_TOP_TRACE_29 IOMUX_PAD(0x6ec, 0x288, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA4__ATA_DATA_4 IOMUX_PAD(0x6f0, 0x28c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__ESDHC3_CMD IOMUX_PAD(0x6f0, 0x28c, 1, 0x818, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__USB_TOP_USBOTG_DATA_6 IOMUX_PAD(0x6f0, 0x28c, 2, 0x9bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__GPIO2_17 IOMUX_PAD(0x6f0, 0x28c, 5, 0x888, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__IPU_DIAGB_11 IOMUX_PAD(0x6f0, 0x28c, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__ARM11P_TOP_TRACE_30 IOMUX_PAD(0x6f0, 0x28c, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA5__ATA_DATA_5 IOMUX_PAD(0x6f4, 0x290, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__USB_TOP_USBOTG_DATA_7 IOMUX_PAD(0x6f4, 0x290, 2, 0x9c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__GPIO2_18 IOMUX_PAD(0x6f4, 0x290, 5, 0x88c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__IPU_DIAGB_12 IOMUX_PAD(0x6f4, 0x290, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__ARM11P_TOP_TRACE_31 IOMUX_PAD(0x6f4, 0x290, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA6__ATA_DATA_6 IOMUX_PAD(0x6f8, 0x294, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__CAN1_TXCAN IOMUX_PAD(0x6f8, 0x294, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__UART1_DTR IOMUX_PAD(0x6f8, 0x294, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__AUDMUX_AUD6_TXD IOMUX_PAD(0x6f8, 0x294, 3, 0x7b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__GPIO2_19 IOMUX_PAD(0x6f8, 0x294, 5, 0x890, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__IPU_DIAGB_13 IOMUX_PAD(0x6f8, 0x294, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA7__ATA_DATA_7 IOMUX_PAD(0x6fc, 0x298, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__CAN1_RXCAN IOMUX_PAD(0x6fc, 0x298, 1, 0x7c8, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__UART1_DSR IOMUX_PAD(0x6fc, 0x298, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__AUDMUX_AUD6_RXD IOMUX_PAD(0x6fc, 0x298, 3, 0x7b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__GPIO2_20 IOMUX_PAD(0x6fc, 0x298, 5, 0x898, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__IPU_DIAGB_14 IOMUX_PAD(0x6fc, 0x298, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA8__ATA_DATA_8 IOMUX_PAD(0x700, 0x29c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__UART3_RTS IOMUX_PAD(0x700, 0x29c, 1, 0x99c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__UART1_RI IOMUX_PAD(0x700, 0x29c, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__AUDMUX_AUD6_TXC IOMUX_PAD(0x700, 0x29c, 3, 0x7c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__GPIO2_21 IOMUX_PAD(0x700, 0x29c, 5, 0x89c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__IPU_DIAGB_15 IOMUX_PAD(0x700, 0x29c, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA9__ATA_DATA_9 IOMUX_PAD(0x704, 0x2a0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__UART3_CTS IOMUX_PAD(0x704, 0x2a0, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__UART1_DCD IOMUX_PAD(0x704, 0x2a0, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__AUDMUX_AUD6_TXFS IOMUX_PAD(0x704, 0x2a0, 3, 0x7c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__GPIO2_22 IOMUX_PAD(0x704, 0x2a0, 5, 0x8a0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__IPU_DIAGB_16 IOMUX_PAD(0x704, 0x2a0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA10__ATA_DATA_10 IOMUX_PAD(0x708, 0x2a4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__UART3_RXD_MUX IOMUX_PAD(0x708, 0x2a4, 1, 0x9a0, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__AUDMUX_AUD6_RXC IOMUX_PAD(0x708, 0x2a4, 3, 0x7b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__GPIO2_23 IOMUX_PAD(0x708, 0x2a4, 5, 0x8a4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__IPU_DIAGB_17 IOMUX_PAD(0x708, 0x2a4, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA11__ATA_DATA_11 IOMUX_PAD(0x70c, 0x2a8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__UART3_TXD_MUX IOMUX_PAD(0x70c, 0x2a8, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__AUDMUX_AUD6_RXFS IOMUX_PAD(0x70c, 0x2a8, 3, 0x7bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__GPIO2_24 IOMUX_PAD(0x70c, 0x2a8, 5, 0x8a8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__IPU_DIAGB_18 IOMUX_PAD(0x70c, 0x2a8, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA12__ATA_DATA_12 IOMUX_PAD(0x710, 0x2ac, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__I2C3_SCL IOMUX_PAD(0x710, 0x2ac, 1, 0x91c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__GPIO2_25 IOMUX_PAD(0x710, 0x2ac, 5, 0x8ac, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__IPU_DIAGB_19 IOMUX_PAD(0x710, 0x2ac, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA13__ATA_DATA_13 IOMUX_PAD(0x714, 0x2b0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__I2C3_SDA IOMUX_PAD(0x714, 0x2b0, 1, 0x920, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__GPIO2_26 IOMUX_PAD(0x714, 0x2b0, 5, 0x8b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__IPU_DIAGB_20 IOMUX_PAD(0x714, 0x2b0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA14__ATA_DATA_14 IOMUX_PAD(0x718, 0x2b4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__IPU_CSI_D_0 IOMUX_PAD(0x718, 0x2b4, 1, 0x930, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__KPP_ROW_0 IOMUX_PAD(0x718, 0x2b4, 3, 0x970, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__GPIO2_27 IOMUX_PAD(0x718, 0x2b4, 5, 0x8b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__IPU_DIAGB_21 IOMUX_PAD(0x718, 0x2b4, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA15__ATA_DATA_15 IOMUX_PAD(0x71c, 0x2b8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__IPU_CSI_D_1 IOMUX_PAD(0x71c, 0x2b8, 1, 0x934, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__KPP_ROW_1 IOMUX_PAD(0x71c, 0x2b8, 3, 0x974, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__GPIO2_28 IOMUX_PAD(0x71c, 0x2b8, 5, 0x8b8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__IPU_DIAGB_22 IOMUX_PAD(0x71c, 0x2b8, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_INTRQ__ATA_INTRQ IOMUX_PAD(0x720, 0x2bc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__IPU_CSI_D_2 IOMUX_PAD(0x720, 0x2bc, 1, 0x938, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__KPP_ROW_2 IOMUX_PAD(0x720, 0x2bc, 3, 0x978, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__GPIO2_29 IOMUX_PAD(0x720, 0x2bc, 5, 0x8bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__IPU_DIAGB_23 IOMUX_PAD(0x720, 0x2bc, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_BUFF_EN__ATA_BUFFER_EN IOMUX_PAD(0x724, 0x2c0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__IPU_CSI_D_3 IOMUX_PAD(0x724, 0x2c0, 1, 0x93c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__KPP_ROW_3 IOMUX_PAD(0x724, 0x2c0, 3, 0x97c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__GPIO2_30 IOMUX_PAD(0x724, 0x2c0, 5, 0x8c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__IPU_DIAGB_24 IOMUX_PAD(0x724, 0x2c0, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DMARQ__ATA_DMARQ IOMUX_PAD(0x728, 0x2c4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__IPU_CSI_D_4 IOMUX_PAD(0x728, 0x2c4, 1, 0x940, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__KPP_COL_0 IOMUX_PAD(0x728, 0x2c4, 3, 0x950, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__GPIO2_31 IOMUX_PAD(0x728, 0x2c4, 5, 0x8c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__IPU_DIAGB_25 IOMUX_PAD(0x728, 0x2c4, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__ECT_CTI_TRIG_IN1_4 IOMUX_PAD(0x728, 0x2c4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA0__ATA_DA_0 IOMUX_PAD(0x72c, 0x2c8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__IPU_CSI_D_5 IOMUX_PAD(0x72c, 0x2c8, 1, 0x944, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__KPP_COL_1 IOMUX_PAD(0x72c, 0x2c8, 3, 0x954, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__GPIO3_0 IOMUX_PAD(0x72c, 0x2c8, 5, 0x8e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__IPU_DIAGB_26 IOMUX_PAD(0x72c, 0x2c8, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__ECT_CTI_TRIG_IN1_5 IOMUX_PAD(0x72c, 0x2c8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA1__ATA_DA_1 IOMUX_PAD(0x730, 0x2cc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__IPU_CSI_D_6 IOMUX_PAD(0x730, 0x2cc, 1, 0x948, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__KPP_COL_2 IOMUX_PAD(0x730, 0x2cc, 3, 0x958, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__GPIO3_1 IOMUX_PAD(0x730, 0x2cc, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__IPU_DIAGB_27 IOMUX_PAD(0x730, 0x2cc, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__ECT_CTI_TRIG_IN1_6 IOMUX_PAD(0x730, 0x2cc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA2__ATA_DA_2 IOMUX_PAD(0x734, 0x2d0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__IPU_CSI_D_7 IOMUX_PAD(0x734, 0x2d0, 1, 0x94c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__KPP_COL_3 IOMUX_PAD(0x734, 0x2d0, 3, 0x95c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__GPIO3_2 IOMUX_PAD(0x734, 0x2d0, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__IPU_DIAGB_28 IOMUX_PAD(0x734, 0x2d0, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__ECT_CTI_TRIG_IN1_7 IOMUX_PAD(0x734, 0x2d0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_CLK__MLB_MLBCLK IOMUX_PAD(0x738, 0x2d4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_CLK__GPIO3_3 IOMUX_PAD(0x738, 0x2d4, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_DAT__MLB_MLBDAT IOMUX_PAD(0x73c, 0x2d8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_DAT__GPIO3_4 IOMUX_PAD(0x73c, 0x2d8, 5, 0x904, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_SIG__MLB_MLBSIG IOMUX_PAD(0x740, 0x2dc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_SIG__GPIO3_5 IOMUX_PAD(0x740, 0x2dc, 5, 0x908, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_CLK__FEC_TX_CLK IOMUX_PAD(0x744, 0x2e0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__ESDHC1_DAT4 IOMUX_PAD(0x744, 0x2e0, 1, 0x804, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__UART3_RXD_MUX IOMUX_PAD(0x744, 0x2e0, 2, 0x9a0, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__USB_TOP_USBH2_DIR IOMUX_PAD(0x744, 0x2e0, 3, 0x9ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__CSPI2_MOSI IOMUX_PAD(0x744, 0x2e0, 4, 0x7ec, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__GPIO3_6 IOMUX_PAD(0x744, 0x2e0, 5, 0x90c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x744, 0x2e0, 6, 0x928, 5, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__ARM11P_TOP_EVNTBUS_0 IOMUX_PAD(0x744, 0x2e0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_CLK__FEC_RX_CLK IOMUX_PAD(0x748, 0x2e4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__ESDHC1_DAT5 IOMUX_PAD(0x748, 0x2e4, 1, 0x808, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__UART3_TXD_MUX IOMUX_PAD(0x748, 0x2e4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__USB_TOP_USBH2_STP IOMUX_PAD(0x748, 0x2e4, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__CSPI2_MISO IOMUX_PAD(0x748, 0x2e4, 4, 0x7e8, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__GPIO3_7 IOMUX_PAD(0x748, 0x2e4, 5, 0x910, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__IPU_DISPB_SD_D_I IOMUX_PAD(0x748, 0x2e4, 6, 0x92c, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__ARM11P_TOP_EVNTBUS_1 IOMUX_PAD(0x748, 0x2e4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_DV__FEC_RX_DV IOMUX_PAD(0x74c, 0x2e8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__ESDHC1_DAT6 IOMUX_PAD(0x74c, 0x2e8, 1, 0x80c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__UART3_RTS IOMUX_PAD(0x74c, 0x2e8, 2, 0x99c, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__USB_TOP_USBH2_NXT IOMUX_PAD(0x74c, 0x2e8, 3, 0x9f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__CSPI2_SCLK IOMUX_PAD(0x74c, 0x2e8, 4, 0x7e0, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__GPIO3_8 IOMUX_PAD(0x74c, 0x2e8, 5, 0x914, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__IPU_DISPB_SD_CLK IOMUX_PAD(0x74c, 0x2e8, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__ARM11P_TOP_EVNTBUS_2 IOMUX_PAD(0x74c, 0x2e8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_COL__FEC_COL IOMUX_PAD(0x750, 0x2ec, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__ESDHC1_DAT7 IOMUX_PAD(0x750, 0x2ec, 1, 0x810, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__UART3_CTS IOMUX_PAD(0x750, 0x2ec, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__USB_TOP_USBH2_DATA_0 IOMUX_PAD(0x750, 0x2ec, 3, 0x9cc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__CSPI2_RDY IOMUX_PAD(0x750, 0x2ec, 4, 0x7e4, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__GPIO3_9 IOMUX_PAD(0x750, 0x2ec, 5, 0x918, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__IPU_DISPB_SER_RS IOMUX_PAD(0x750, 0x2ec, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__ARM11P_TOP_EVNTBUS_3 IOMUX_PAD(0x750, 0x2ec, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA0__FEC_RDATA_0 IOMUX_PAD(0x754, 0x2f0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__PWM_PWMO IOMUX_PAD(0x754, 0x2f0, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__UART3_DTR IOMUX_PAD(0x754, 0x2f0, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__USB_TOP_USBH2_DATA_1 IOMUX_PAD(0x754, 0x2f0, 3, 0x9d0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__CSPI2_SS0 IOMUX_PAD(0x754, 0x2f0, 4, 0x7f0, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__GPIO3_10 IOMUX_PAD(0x754, 0x2f0, 5, 0x8ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__IPU_DISPB_CS1 IOMUX_PAD(0x754, 0x2f0, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__ARM11P_TOP_EVNTBUS_4 IOMUX_PAD(0x754, 0x2f0, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA0__FEC_TDATA_0 IOMUX_PAD(0x758, 0x2f4, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x758, 0x2f4, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__UART3_DSR IOMUX_PAD(0x758, 0x2f4, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__USB_TOP_USBH2_DATA_2 IOMUX_PAD(0x758, 0x2f4, 3, 0x9d4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__CSPI2_SS1 IOMUX_PAD(0x758, 0x2f4, 4, 0x7f4, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__GPIO3_11 IOMUX_PAD(0x758, 0x2f4, 5, 0x8f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__IPU_DISPB_CS0 IOMUX_PAD(0x758, 0x2f4, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__ARM11P_TOP_EVNTBUS_5 IOMUX_PAD(0x758, 0x2f4, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_EN__FEC_TX_EN IOMUX_PAD(0x75c, 0x2f8, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__SPDIF_SPDIF_IN1 IOMUX_PAD(0x75c, 0x2f8, 1, 0x998, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__UART3_RI IOMUX_PAD(0x75c, 0x2f8, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__USB_TOP_USBH2_DATA_3 IOMUX_PAD(0x75c, 0x2f8, 3, 0x9d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__GPIO3_12 IOMUX_PAD(0x75c, 0x2f8, 5, 0x8f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__IPU_DISPB_PAR_RS IOMUX_PAD(0x75c, 0x2f8, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__ARM11P_TOP_EVNTBUS_6 IOMUX_PAD(0x75c, 0x2f8, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_MDC__FEC_MDC IOMUX_PAD(0x760, 0x2fc, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__CAN2_TXCAN IOMUX_PAD(0x760, 0x2fc, 1, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__UART3_DCD IOMUX_PAD(0x760, 0x2fc, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__USB_TOP_USBH2_DATA_4 IOMUX_PAD(0x760, 0x2fc, 3, 0x9dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__GPIO3_13 IOMUX_PAD(0x760, 0x2fc, 5, 0x8f8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__IPU_DISPB_WR IOMUX_PAD(0x760, 0x2fc, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__ARM11P_TOP_EVNTBUS_7 IOMUX_PAD(0x760, 0x2fc, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x764, 0x300, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__CAN2_RXCAN IOMUX_PAD(0x764, 0x300, 1, 0x7cc, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__USB_TOP_USBH2_DATA_5 IOMUX_PAD(0x764, 0x300, 3, 0x9e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__GPIO3_14 IOMUX_PAD(0x764, 0x300, 5, 0x8fc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__IPU_DISPB_RD IOMUX_PAD(0x764, 0x300, 6, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__ARM11P_TOP_EVNTBUS_8 IOMUX_PAD(0x764, 0x300, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_ERR__FEC_TX_ERR IOMUX_PAD(0x768, 0x304, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__OWIRE_LINE IOMUX_PAD(0x768, 0x304, 1, 0x990, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x768, 0x304, 2, 0x994, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__USB_TOP_USBH2_DATA_6 IOMUX_PAD(0x768, 0x304, 3, 0x9e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__GPIO3_15 IOMUX_PAD(0x768, 0x304, 5, 0x900, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x768, 0x304, 6, 0x924, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__ARM11P_TOP_EVNTBUS_9 IOMUX_PAD(0x768, 0x304, 7, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_ERR__FEC_RX_ERR IOMUX_PAD(0x76c, 0x308, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__IPU_CSI_D_0 IOMUX_PAD(0x76c, 0x308, 1, 0x930, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__USB_TOP_USBH2_DATA_7 IOMUX_PAD(0x76c, 0x308, 3, 0x9e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__KPP_COL_4 IOMUX_PAD(0x76c, 0x308, 4, 0x960, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__GPIO3_16 IOMUX_PAD(0x76c, 0x308, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__IPU_DISPB_SD_D_IO IOMUX_PAD(0x76c, 0x308, 6, 0x92c, 5, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_CRS__FEC_CRS IOMUX_PAD(0x770, 0x30c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__IPU_CSI_D_1 IOMUX_PAD(0x770, 0x30c, 1, 0x934, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__USB_TOP_USBH2_PWR IOMUX_PAD(0x770, 0x30c, 3, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__KPP_COL_5 IOMUX_PAD(0x770, 0x30c, 4, 0x964, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__GPIO3_17 IOMUX_PAD(0x770, 0x30c, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__IPU_FLASH_STROBE IOMUX_PAD(0x770, 0x30c, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA1__FEC_RDATA_1 IOMUX_PAD(0x774, 0x310, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__IPU_CSI_D_2 IOMUX_PAD(0x774, 0x310, 1, 0x938, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__AUDMUX_AUD6_RXC IOMUX_PAD(0x774, 0x310, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__USB_TOP_USBH2_OC IOMUX_PAD(0x774, 0x310, 3, 0x9f4, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__KPP_COL_6 IOMUX_PAD(0x774, 0x310, 4, 0x968, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__GPIO3_18 IOMUX_PAD(0x774, 0x310, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__IPU_DISPB_BE0 IOMUX_PAD(0x774, 0x310, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA1__FEC_TDATA_1 IOMUX_PAD(0x778, 0x314, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__IPU_CSI_D_3 IOMUX_PAD(0x778, 0x314, 1, 0x93c, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__AUDMUX_AUD6_RXFS IOMUX_PAD(0x778, 0x314, 2, 0x7bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__KPP_COL_7 IOMUX_PAD(0x778, 0x314, 4, 0x96c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__GPIO3_19 IOMUX_PAD(0x778, 0x314, 5, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__IPU_DISPB_BE1 IOMUX_PAD(0x778, 0x314, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA2__FEC_RDATA_2 IOMUX_PAD(0x77c, 0x318, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__IPU_CSI_D_4 IOMUX_PAD(0x77c, 0x318, 1, 0x940, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__AUDMUX_AUD6_TXD IOMUX_PAD(0x77c, 0x318, 2, 0x7b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__KPP_ROW_4 IOMUX_PAD(0x77c, 0x318, 4, 0x980, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__GPIO3_20 IOMUX_PAD(0x77c, 0x318, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA2__FEC_TDATA_2 IOMUX_PAD(0x780, 0x31c, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__IPU_CSI_D_5 IOMUX_PAD(0x780, 0x31c, 1, 0x944, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__AUDMUX_AUD6_RXD IOMUX_PAD(0x780, 0x31c, 2, 0x7b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__KPP_ROW_5 IOMUX_PAD(0x780, 0x31c, 4, 0x984, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__GPIO3_21 IOMUX_PAD(0x780, 0x31c, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA3__FEC_RDATA_3 IOMUX_PAD(0x784, 0x320, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__IPU_CSI_D_6 IOMUX_PAD(0x784, 0x320, 1, 0x948, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__AUDMUX_AUD6_TXC IOMUX_PAD(0x784, 0x320, 2, 0x7c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__KPP_ROW_6 IOMUX_PAD(0x784, 0x320, 4, 0x988, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__GPIO3_22 IOMUX_PAD(0x784, 0x320, 6, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA3__FEC_TDATA_3 IOMUX_PAD(0x788, 0x324, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__IPU_CSI_D_7 IOMUX_PAD(0x788, 0x324, 1, 0x94c, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__AUDMUX_AUD6_TXFS IOMUX_PAD(0x788, 0x324, 2, 0x7c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__KPP_ROW_7 IOMUX_PAD(0x788, 0x324, 4, 0x98c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__GPIO3_23 IOMUX_PAD(0x788, 0x324, 5, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_EXT_ARMCLK__CCM_EXT_ARMCLK IOMUX_PAD(0x78c, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TEST_MODE__TCU_TEST_MODE IOMUX_PAD(0x790, 0x0, 0, 0x0, 0, NO_PAD_CTRL)
-
-
-#endif /* __MACH_IOMUX_MX35_H__ */
diff --git a/arch/arm/mach-imx/iomux-v1.c b/arch/arm/mach-imx/iomux-v1.c
deleted file mode 100644
index a4bec3b..0000000
--- a/arch/arm/mach-imx/iomux-v1.c
+++ /dev/null
@@ -1,174 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/plat-mxc/iomux-v1.c
- *
- * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH
- * Copyright (C) 2009 Uwe Kleine-Koenig, Pengutronix
- *
- * Common code for i.MX1, i.MX21 and i.MX27
- */
-
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/gpio.h>
-
-#include <asm/mach/map.h>
-
-#include "hardware.h"
-#include "iomux-v1.h"
-
-static void __iomem *imx_iomuxv1_baseaddr;
-static unsigned imx_iomuxv1_numports;
-
-static inline unsigned long imx_iomuxv1_readl(unsigned offset)
-{
- return imx_readl(imx_iomuxv1_baseaddr + offset);
-}
-
-static inline void imx_iomuxv1_writel(unsigned long val, unsigned offset)
-{
- imx_writel(val, imx_iomuxv1_baseaddr + offset);
-}
-
-static inline void imx_iomuxv1_rmwl(unsigned offset,
- unsigned long mask, unsigned long value)
-{
- unsigned long reg = imx_iomuxv1_readl(offset);
-
- reg &= ~mask;
- reg |= value;
-
- imx_iomuxv1_writel(reg, offset);
-}
-
-static inline void imx_iomuxv1_set_puen(
- unsigned int port, unsigned int pin, int on)
-{
- unsigned long mask = 1 << pin;
-
- imx_iomuxv1_rmwl(MXC_PUEN(port), mask, on ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_ddir(
- unsigned int port, unsigned int pin, int out)
-{
- unsigned long mask = 1 << pin;
-
- imx_iomuxv1_rmwl(MXC_DDIR(port), mask, out ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_gpr(
- unsigned int port, unsigned int pin, int af)
-{
- unsigned long mask = 1 << pin;
-
- imx_iomuxv1_rmwl(MXC_GPR(port), mask, af ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_gius(
- unsigned int port, unsigned int pin, int inuse)
-{
- unsigned long mask = 1 << pin;
-
- imx_iomuxv1_rmwl(MXC_GIUS(port), mask, inuse ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_ocr(
- unsigned int port, unsigned int pin, unsigned int ocr)
-{
- unsigned long shift = (pin & 0xf) << 1;
- unsigned long mask = 3 << shift;
- unsigned long value = ocr << shift;
- unsigned long offset = pin < 16 ? MXC_OCR1(port) : MXC_OCR2(port);
-
- imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-static inline void imx_iomuxv1_set_iconfa(
- unsigned int port, unsigned int pin, unsigned int aout)
-{
- unsigned long shift = (pin & 0xf) << 1;
- unsigned long mask = 3 << shift;
- unsigned long value = aout << shift;
- unsigned long offset = pin < 16 ? MXC_ICONFA1(port) : MXC_ICONFA2(port);
-
- imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-static inline void imx_iomuxv1_set_iconfb(
- unsigned int port, unsigned int pin, unsigned int bout)
-{
- unsigned long shift = (pin & 0xf) << 1;
- unsigned long mask = 3 << shift;
- unsigned long value = bout << shift;
- unsigned long offset = pin < 16 ? MXC_ICONFB1(port) : MXC_ICONFB2(port);
-
- imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-int mxc_gpio_mode(int gpio_mode)
-{
- unsigned int pin = gpio_mode & GPIO_PIN_MASK;
- unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> GPIO_PORT_SHIFT;
- unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> GPIO_OCR_SHIFT;
- unsigned int aout = (gpio_mode >> GPIO_AOUT_SHIFT) & 3;
- unsigned int bout = (gpio_mode >> GPIO_BOUT_SHIFT) & 3;
-
- if (port >= imx_iomuxv1_numports)
- return -EINVAL;
-
- /* Pullup enable */
- imx_iomuxv1_set_puen(port, pin, gpio_mode & GPIO_PUEN);
-
- /* Data direction */
- imx_iomuxv1_set_ddir(port, pin, gpio_mode & GPIO_OUT);
-
- /* Primary / alternate function */
- imx_iomuxv1_set_gpr(port, pin, gpio_mode & GPIO_AF);
-
- /* use as gpio? */
- imx_iomuxv1_set_gius(port, pin, !(gpio_mode & (GPIO_PF | GPIO_AF)));
-
- imx_iomuxv1_set_ocr(port, pin, ocr);
-
- imx_iomuxv1_set_iconfa(port, pin, aout);
-
- imx_iomuxv1_set_iconfb(port, pin, bout);
-
- return 0;
-}
-
-static int imx_iomuxv1_setup_multiple(const int *list, unsigned count)
-{
- size_t i;
- int ret = 0;
-
- for (i = 0; i < count; ++i) {
- ret = mxc_gpio_mode(list[i]);
-
- if (ret)
- return ret;
- }
-
- return ret;
-}
-
-int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count,
- const char *label)
-{
- int ret;
-
- ret = imx_iomuxv1_setup_multiple(pin_list, count);
- return ret;
-}
-
-int __init imx_iomuxv1_init(void __iomem *base, int numports)
-{
- imx_iomuxv1_baseaddr = base;
- imx_iomuxv1_numports = numports;
-
- return 0;
-}
diff --git a/arch/arm/mach-imx/iomux-v1.h b/arch/arm/mach-imx/iomux-v1.h
deleted file mode 100644
index b948529..0000000
--- a/arch/arm/mach-imx/iomux-v1.h
+++ /dev/null
@@ -1,81 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_V1_H__
-#define __MACH_IOMUX_V1_H__
-
-/*
-* GPIO Module and I/O Multiplexer
-* x = 0..3 for reg_A, reg_B, reg_C, reg_D
-*/
-#define MXC_DDIR(x) (0x00 + ((x) << 8))
-#define MXC_OCR1(x) (0x04 + ((x) << 8))
-#define MXC_OCR2(x) (0x08 + ((x) << 8))
-#define MXC_ICONFA1(x) (0x0c + ((x) << 8))
-#define MXC_ICONFA2(x) (0x10 + ((x) << 8))
-#define MXC_ICONFB1(x) (0x14 + ((x) << 8))
-#define MXC_ICONFB2(x) (0x18 + ((x) << 8))
-#define MXC_DR(x) (0x1c + ((x) << 8))
-#define MXC_GIUS(x) (0x20 + ((x) << 8))
-#define MXC_SSR(x) (0x24 + ((x) << 8))
-#define MXC_ICR1(x) (0x28 + ((x) << 8))
-#define MXC_ICR2(x) (0x2c + ((x) << 8))
-#define MXC_IMR(x) (0x30 + ((x) << 8))
-#define MXC_ISR(x) (0x34 + ((x) << 8))
-#define MXC_GPR(x) (0x38 + ((x) << 8))
-#define MXC_SWR(x) (0x3c + ((x) << 8))
-#define MXC_PUEN(x) (0x40 + ((x) << 8))
-
-#define MX1_NUM_GPIO_PORT 4
-#define MX21_NUM_GPIO_PORT 6
-#define MX27_NUM_GPIO_PORT 6
-
-#define GPIO_PIN_MASK 0x1f
-
-#define GPIO_PORT_SHIFT 5
-#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT)
-
-#define GPIO_PORTA (0 << GPIO_PORT_SHIFT)
-#define GPIO_PORTB (1 << GPIO_PORT_SHIFT)
-#define GPIO_PORTC (2 << GPIO_PORT_SHIFT)
-#define GPIO_PORTD (3 << GPIO_PORT_SHIFT)
-#define GPIO_PORTE (4 << GPIO_PORT_SHIFT)
-#define GPIO_PORTF (5 << GPIO_PORT_SHIFT)
-
-#define GPIO_OUT (1 << 8)
-#define GPIO_IN (0 << 8)
-#define GPIO_PUEN (1 << 9)
-
-#define GPIO_PF (1 << 10)
-#define GPIO_AF (1 << 11)
-
-#define GPIO_OCR_SHIFT 12
-#define GPIO_OCR_MASK (3 << GPIO_OCR_SHIFT)
-#define GPIO_AIN (0 << GPIO_OCR_SHIFT)
-#define GPIO_BIN (1 << GPIO_OCR_SHIFT)
-#define GPIO_CIN (2 << GPIO_OCR_SHIFT)
-#define GPIO_GPIO (3 << GPIO_OCR_SHIFT)
-
-#define GPIO_AOUT_SHIFT 14
-#define GPIO_AOUT_MASK (3 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT (0 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_ISR (1 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_0 (2 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_1 (3 << GPIO_AOUT_SHIFT)
-
-#define GPIO_BOUT_SHIFT 16
-#define GPIO_BOUT_MASK (3 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT (0 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_ISR (1 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_0 (2 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_1 (3 << GPIO_BOUT_SHIFT)
-
-extern int mxc_gpio_mode(int gpio_mode);
-extern int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count,
- const char *label);
-
-extern int imx_iomuxv1_init(void __iomem *base, int numports);
-
-#endif /* __MACH_IOMUX_V1_H__ */
diff --git a/arch/arm/mach-imx/iomux-v3.c b/arch/arm/mach-imx/iomux-v3.c
deleted file mode 100644
index 043cf3c..0000000
--- a/arch/arm/mach-imx/iomux-v3.c
+++ /dev/null
@@ -1,65 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
- * <armlinux@phytec.de>
- */
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/gpio.h>
-
-#include <asm/mach/map.h>
-
-#include "hardware.h"
-#include "iomux-v3.h"
-
-static void __iomem *base;
-
-/*
- * configures a single pad in the iomuxer
- */
-int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad)
-{
- u32 mux_ctrl_ofs = (pad & MUX_CTRL_OFS_MASK) >> MUX_CTRL_OFS_SHIFT;
- u32 mux_mode = (pad & MUX_MODE_MASK) >> MUX_MODE_SHIFT;
- u32 sel_input_ofs = (pad & MUX_SEL_INPUT_OFS_MASK) >> MUX_SEL_INPUT_OFS_SHIFT;
- u32 sel_input = (pad & MUX_SEL_INPUT_MASK) >> MUX_SEL_INPUT_SHIFT;
- u32 pad_ctrl_ofs = (pad & MUX_PAD_CTRL_OFS_MASK) >> MUX_PAD_CTRL_OFS_SHIFT;
- u32 pad_ctrl = (pad & MUX_PAD_CTRL_MASK) >> MUX_PAD_CTRL_SHIFT;
-
- if (mux_ctrl_ofs)
- imx_writel(mux_mode, base + mux_ctrl_ofs);
-
- if (sel_input_ofs)
- imx_writel(sel_input, base + sel_input_ofs);
-
- if (!(pad_ctrl & NO_PAD_CTRL) && pad_ctrl_ofs)
- imx_writel(pad_ctrl, base + pad_ctrl_ofs);
-
- return 0;
-}
-
-int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
- unsigned count)
-{
- const iomux_v3_cfg_t *p = pad_list;
- int i;
- int ret;
-
- for (i = 0; i < count; i++) {
- ret = mxc_iomux_v3_setup_pad(*p);
- if (ret)
- return ret;
- p++;
- }
- return 0;
-}
-
-void mxc_iomux_v3_init(void __iomem *iomux_v3_base)
-{
- base = iomux_v3_base;
-}
diff --git a/arch/arm/mach-imx/iomux-v3.h b/arch/arm/mach-imx/iomux-v3.h
deleted file mode 100644
index 7db8ec9..0000000
--- a/arch/arm/mach-imx/iomux-v3.h
+++ /dev/null
@@ -1,130 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
- * <armlinux@phytec.de>
- */
-
-#ifndef __MACH_IOMUX_V3_H__
-#define __MACH_IOMUX_V3_H__
-
-/*
- * build IOMUX_PAD structure
- *
- * This iomux scheme is based around pads, which are the physical balls
- * on the processor.
- *
- * - Each pad has a pad control register (IOMUXC_SW_PAD_CTRL_x) which controls
- * things like driving strength and pullup/pulldown.
- * - Each pad can have but not necessarily does have an output routing register
- * (IOMUXC_SW_MUX_CTL_PAD_x).
- * - Each pad can have but not necessarily does have an input routing register
- * (IOMUXC_x_SELECT_INPUT)
- *
- * The three register sets do not have a fixed offset to each other,
- * hence we order this table by pad control registers (which all pads
- * have) and put the optional i/o routing registers into additional
- * fields.
- *
- * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode>
- * If <padname> or <padmode> refers to a GPIO, it is named
- * GPIO_<unit>_<num>
- *
- * IOMUX/PAD Bit field definitions
- *
- * MUX_CTRL_OFS: 0..11 (12)
- * PAD_CTRL_OFS: 12..23 (12)
- * SEL_INPUT_OFS: 24..35 (12)
- * MUX_MODE + SION: 36..40 (5)
- * PAD_CTRL + NO_PAD_CTRL: 41..57 (17)
- * SEL_INP: 58..61 (4)
- * reserved: 63 (1)
-*/
-
-typedef u64 iomux_v3_cfg_t;
-
-#define MUX_CTRL_OFS_SHIFT 0
-#define MUX_CTRL_OFS_MASK ((iomux_v3_cfg_t)0xfff << MUX_CTRL_OFS_SHIFT)
-#define MUX_PAD_CTRL_OFS_SHIFT 12
-#define MUX_PAD_CTRL_OFS_MASK ((iomux_v3_cfg_t)0xfff << MUX_PAD_CTRL_OFS_SHIFT)
-#define MUX_SEL_INPUT_OFS_SHIFT 24
-#define MUX_SEL_INPUT_OFS_MASK ((iomux_v3_cfg_t)0xfff << MUX_SEL_INPUT_OFS_SHIFT)
-
-#define MUX_MODE_SHIFT 36
-#define MUX_MODE_MASK ((iomux_v3_cfg_t)0x1f << MUX_MODE_SHIFT)
-#define MUX_PAD_CTRL_SHIFT 41
-#define MUX_PAD_CTRL_MASK ((iomux_v3_cfg_t)0x1ffff << MUX_PAD_CTRL_SHIFT)
-#define MUX_SEL_INPUT_SHIFT 58
-#define MUX_SEL_INPUT_MASK ((iomux_v3_cfg_t)0xf << MUX_SEL_INPUT_SHIFT)
-
-#define MUX_PAD_CTRL(x) ((iomux_v3_cfg_t)(x) << MUX_PAD_CTRL_SHIFT)
-
-#define IOMUX_PAD(_pad_ctrl_ofs, _mux_ctrl_ofs, _mux_mode, _sel_input_ofs, \
- _sel_input, _pad_ctrl) \
- (((iomux_v3_cfg_t)(_mux_ctrl_ofs) << MUX_CTRL_OFS_SHIFT) | \
- ((iomux_v3_cfg_t)(_mux_mode) << MUX_MODE_SHIFT) | \
- ((iomux_v3_cfg_t)(_pad_ctrl_ofs) << MUX_PAD_CTRL_OFS_SHIFT) | \
- ((iomux_v3_cfg_t)(_pad_ctrl) << MUX_PAD_CTRL_SHIFT) | \
- ((iomux_v3_cfg_t)(_sel_input_ofs) << MUX_SEL_INPUT_OFS_SHIFT) | \
- ((iomux_v3_cfg_t)(_sel_input) << MUX_SEL_INPUT_SHIFT))
-
-#define NEW_PAD_CTRL(cfg, pad) (((cfg) & ~MUX_PAD_CTRL_MASK) | MUX_PAD_CTRL(pad))
-/*
- * Use to set PAD control
- */
-
-#define NO_PAD_CTRL (1 << 16)
-#define PAD_CTL_DVS (1 << 13)
-#define PAD_CTL_HYS (1 << 8)
-
-#define PAD_CTL_PKE (1 << 7)
-#define PAD_CTL_PUE (1 << 6 | PAD_CTL_PKE)
-#define PAD_CTL_PUS_100K_DOWN (0 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_47K_UP (1 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_100K_UP (2 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_22K_UP (3 << 4 | PAD_CTL_PUE)
-
-#define PAD_CTL_ODE (1 << 3)
-
-#define PAD_CTL_DSE_LOW (0 << 1)
-#define PAD_CTL_DSE_MED (1 << 1)
-#define PAD_CTL_DSE_HIGH (2 << 1)
-#define PAD_CTL_DSE_MAX (3 << 1)
-
-#define PAD_CTL_SRE_FAST (1 << 0)
-#define PAD_CTL_SRE_SLOW (0 << 0)
-
-#define IOMUX_CONFIG_SION (0x1 << 4)
-
-#define MX51_NUM_GPIO_PORT 4
-
-#define GPIO_PIN_MASK 0x1f
-
-#define GPIO_PORT_SHIFT 5
-#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT)
-
-#define GPIO_PORTA (0 << GPIO_PORT_SHIFT)
-#define GPIO_PORTB (1 << GPIO_PORT_SHIFT)
-#define GPIO_PORTC (2 << GPIO_PORT_SHIFT)
-#define GPIO_PORTD (3 << GPIO_PORT_SHIFT)
-#define GPIO_PORTE (4 << GPIO_PORT_SHIFT)
-#define GPIO_PORTF (5 << GPIO_PORT_SHIFT)
-
-/*
- * setups a single pad in the iomuxer
- */
-int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad);
-
-/*
- * setups multiple pads
- * convenient way to call the above function with tables
- */
-int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
- unsigned count);
-
-/*
- * Initialise the iomux controller
- */
-void mxc_iomux_v3_init(void __iomem *iomux_v3_base);
-
-#endif /* __MACH_IOMUX_V3_H__*/
-
diff --git a/arch/arm/mach-imx/mach-armadillo5x0.c b/arch/arm/mach-imx/mach-armadillo5x0.c
deleted file mode 100644
index 4d9a56f..0000000
--- a/arch/arm/mach-imx/mach-armadillo5x0.c
+++ /dev/null
@@ -1,562 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * armadillo5x0.c
- *
- * Copyright 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * updates in http://alberdroid.blogspot.com/
- *
- * Based on Atmark Techno, Inc. armadillo 500 BSP 2008
- * Based on mx31ads.c and pcm037.c Great Work!
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/io.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/delay.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "crmregs-imx3.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static int armadillo5x0_pins[] = {
- /* UART1 */
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
- /* UART2 */
- MX31_PIN_CTS2__CTS2,
- MX31_PIN_RTS2__RTS2,
- MX31_PIN_TXD2__TXD2,
- MX31_PIN_RXD2__RXD2,
- /* LAN9118_IRQ */
- IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO),
- /* SDHC1 */
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
- /* Framebuffer */
- MX31_PIN_LD0__LD0,
- MX31_PIN_LD1__LD1,
- MX31_PIN_LD2__LD2,
- MX31_PIN_LD3__LD3,
- MX31_PIN_LD4__LD4,
- MX31_PIN_LD5__LD5,
- MX31_PIN_LD6__LD6,
- MX31_PIN_LD7__LD7,
- MX31_PIN_LD8__LD8,
- MX31_PIN_LD9__LD9,
- MX31_PIN_LD10__LD10,
- MX31_PIN_LD11__LD11,
- MX31_PIN_LD12__LD12,
- MX31_PIN_LD13__LD13,
- MX31_PIN_LD14__LD14,
- MX31_PIN_LD15__LD15,
- MX31_PIN_LD16__LD16,
- MX31_PIN_LD17__LD17,
- MX31_PIN_VSYNC3__VSYNC3,
- MX31_PIN_HSYNC__HSYNC,
- MX31_PIN_FPSHIFT__FPSHIFT,
- MX31_PIN_DRDY0__DRDY0,
- IOMUX_MODE(MX31_PIN_LCS1, IOMUX_CONFIG_GPIO), /*ADV7125_PSAVE*/
- /* I2C2 */
- MX31_PIN_CSPI2_MOSI__SCL,
- MX31_PIN_CSPI2_MISO__SDA,
- /* OTG */
- MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
- MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
- MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
- MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
- MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
- MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
- MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
- MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
- MX31_PIN_USBOTG_CLK__USBOTG_CLK,
- MX31_PIN_USBOTG_DIR__USBOTG_DIR,
- MX31_PIN_USBOTG_NXT__USBOTG_NXT,
- MX31_PIN_USBOTG_STP__USBOTG_STP,
- /* USB host 2 */
- IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
-};
-
-/* USB */
-
-#define OTG_RESET IOMUX_TO_GPIO(MX31_PIN_STXD4)
-#define USBH2_RESET IOMUX_TO_GPIO(MX31_PIN_SCK6)
-#define USBH2_CS IOMUX_TO_GPIO(MX31_PIN_GPIO1_3)
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbotg_init(struct platform_device *pdev)
-{
- int err;
-
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
-
- /* Chip already enabled by hardware */
- /* OTG phy reset*/
- err = gpio_request(OTG_RESET, "USB-OTG-RESET");
- if (err) {
- pr_err("Failed to request the usb otg reset gpio\n");
- return err;
- }
-
- err = gpio_direction_output(OTG_RESET, 1/*HIGH*/);
- if (err) {
- pr_err("Failed to reset the usb otg phy\n");
- goto otg_free_reset;
- }
-
- gpio_set_value(OTG_RESET, 0/*LOW*/);
- mdelay(5);
- gpio_set_value(OTG_RESET, 1/*HIGH*/);
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_INTERFACE_DIFF_UNI);
-
-otg_free_reset:
- gpio_free(OTG_RESET);
- return err;
-}
-
-static int usbh2_init(struct platform_device *pdev)
-{
- int err;
-
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
- mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
-
- /* Enable the chip */
- err = gpio_request(USBH2_CS, "USB-H2-CS");
- if (err) {
- pr_err("Failed to request the usb host 2 CS gpio\n");
- return err;
- }
-
- err = gpio_direction_output(USBH2_CS, 0/*Enabled*/);
- if (err) {
- pr_err("Failed to drive the usb host 2 CS gpio\n");
- goto h2_free_cs;
- }
-
- /* H2 phy reset*/
- err = gpio_request(USBH2_RESET, "USB-H2-RESET");
- if (err) {
- pr_err("Failed to request the usb host 2 reset gpio\n");
- goto h2_free_cs;
- }
-
- err = gpio_direction_output(USBH2_RESET, 1/*HIGH*/);
- if (err) {
- pr_err("Failed to reset the usb host 2 phy\n");
- goto h2_free_reset;
- }
-
- gpio_set_value(USBH2_RESET, 0/*LOW*/);
- mdelay(5);
- gpio_set_value(USBH2_RESET, 1/*HIGH*/);
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_INTERFACE_DIFF_UNI);
-
-h2_free_reset:
- gpio_free(USBH2_RESET);
-h2_free_cs:
- gpio_free(USBH2_CS);
- return err;
-}
-
-static struct mxc_usbh_platform_data usbotg_pdata __initdata = {
- .init = usbotg_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = usbh2_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/* RTC over I2C*/
-#define ARMADILLO5X0_RTC_GPIO IOMUX_TO_GPIO(MX31_PIN_SRXD4)
-
-static struct i2c_board_info armadillo5x0_i2c_rtc = {
- I2C_BOARD_INFO("s35390a", 0x30),
-};
-
-/* GPIO BUTTONS */
-static struct gpio_keys_button armadillo5x0_buttons[] = {
- {
- .code = KEY_ENTER, /*28*/
- .gpio = IOMUX_TO_GPIO(MX31_PIN_SCLK0),
- .active_low = 1,
- .desc = "menu",
- .wakeup = 1,
- }, {
- .code = KEY_BACK, /*158*/
- .gpio = IOMUX_TO_GPIO(MX31_PIN_SRST0),
- .active_low = 1,
- .desc = "back",
- .wakeup = 1,
- }
-};
-
-static const struct gpio_keys_platform_data
- armadillo5x0_button_data __initconst = {
- .buttons = armadillo5x0_buttons,
- .nbuttons = ARRAY_SIZE(armadillo5x0_buttons),
-};
-
-/*
- * NAND Flash
- */
-static const struct mxc_nand_platform_data
-armadillo5x0_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-/*
- * MTD NOR Flash
- */
-static struct mtd_partition armadillo5x0_nor_flash_partitions[] = {
- {
- .name = "nor.bootloader",
- .offset = 0x00000000,
- .size = 4*32*1024,
- }, {
- .name = "nor.kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 16*128*1024,
- }, {
- .name = "nor.userland",
- .offset = MTDPART_OFS_APPEND,
- .size = 110*128*1024,
- }, {
- .name = "nor.config",
- .offset = MTDPART_OFS_APPEND,
- .size = 1*128*1024,
- },
-};
-
-static const struct physmap_flash_data
- armadillo5x0_nor_flash_pdata __initconst = {
- .width = 2,
- .parts = armadillo5x0_nor_flash_partitions,
- .nr_parts = ARRAY_SIZE(armadillo5x0_nor_flash_partitions),
-};
-
-static const struct resource armadillo5x0_nor_flash_resource __initconst = {
- .flags = IORESOURCE_MEM,
- .start = MX31_CS0_BASE_ADDR,
- .end = MX31_CS0_BASE_ADDR + SZ_64M - 1,
-};
-
-/*
- * FB support
- */
-static const struct fb_videomode fb_modedb[] = {
- { /* 640x480 @ 60 Hz */
- .name = "CRT-VGA",
- .refresh = 60,
- .xres = 640,
- .yres = 480,
- .pixclock = 39721,
- .left_margin = 35,
- .right_margin = 115,
- .upper_margin = 43,
- .lower_margin = 1,
- .hsync_len = 10,
- .vsync_len = 1,
- .sync = FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }, {/* 800x600 @ 56 Hz */
- .name = "CRT-SVGA",
- .refresh = 56,
- .xres = 800,
- .yres = 600,
- .pixclock = 30000,
- .left_margin = 30,
- .right_margin = 108,
- .upper_margin = 13,
- .lower_margin = 10,
- .hsync_len = 10,
- .vsync_len = 1,
- .sync = FB_SYNC_OE_ACT_HIGH | FB_SYNC_HOR_HIGH_ACT |
- FB_SYNC_VERT_HIGH_ACT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "CRT-VGA",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-/*
- * SDHC 1
- * MMC support
- */
-static int armadillo5x0_sdhc1_get_ro(struct device *dev)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B));
-}
-
-static int armadillo5x0_sdhc1_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
-{
- int ret;
- int gpio_det, gpio_wp;
-
- gpio_det = IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK);
- gpio_wp = IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B);
-
- ret = gpio_request(gpio_det, "sdhc-card-detect");
- if (ret)
- return ret;
-
- gpio_direction_input(gpio_det);
-
- ret = gpio_request(gpio_wp, "sdhc-write-protect");
- if (ret)
- goto err_gpio_free;
-
- gpio_direction_input(gpio_wp);
-
- /* When supported the trigger type have to be BOTH */
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK)),
- detect_irq, IRQF_TRIGGER_FALLING,
- "sdhc-detect", data);
-
- if (ret)
- goto err_gpio_free_2;
-
- return 0;
-
-err_gpio_free_2:
- gpio_free(gpio_wp);
-
-err_gpio_free:
- gpio_free(gpio_det);
-
- return ret;
-
-}
-
-static void armadillo5x0_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK)), data);
- gpio_free(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK));
- gpio_free(IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B));
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
- .get_ro = armadillo5x0_sdhc1_get_ro,
- .init = armadillo5x0_sdhc1_init,
- .exit = armadillo5x0_sdhc1_exit,
-};
-
-/*
- * SMSC 9118
- * Network support
- */
-static struct resource armadillo5x0_smc911x_resources[] = {
- {
- .start = MX31_CS3_BASE_ADDR,
- .end = MX31_CS3_BASE_ADDR + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
- }, {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct smsc911x_platform_config smsc911x_info = {
- .flags = SMSC911X_USE_16BIT,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
-};
-
-static struct platform_device armadillo5x0_smc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(armadillo5x0_smc911x_resources),
- .resource = armadillo5x0_smc911x_resources,
- .dev = {
- .platform_data = &smsc911x_info,
- },
-};
-
-/* UART device data */
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct platform_device *devices[] __initdata = {
- &armadillo5x0_smc911x_device,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-/*
- * Perform board specific initializations
- */
-static void __init armadillo5x0_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(armadillo5x0_pins,
- ARRAY_SIZE(armadillo5x0_pins), "armadillo5x0");
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- imx31_add_imx_i2c1(NULL);
-
- /* Register UART */
- imx31_add_imx_uart0(&uart_pdata);
- imx31_add_imx_uart1(&uart_pdata);
-
- /* Register FB */
- imx31_add_ipu_core();
- imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
- /* Register NOR Flash */
- platform_device_register_resndata(NULL, "physmap-flash", -1,
- &armadillo5x0_nor_flash_resource, 1,
- &armadillo5x0_nor_flash_pdata,
- sizeof(armadillo5x0_nor_flash_pdata));
-
- /* Register NAND Flash */
- imx31_add_mxc_nand(&armadillo5x0_nand_board_info);
-
- /* set NAND page size to 2k if not configured via boot mode pins */
- imx_writel(imx_readl(mx3_ccm_base + MXC_CCM_RCSR) | (1 << 30),
- mx3_ccm_base + MXC_CCM_RCSR);
-}
-
-static void __init armadillo5x0_late(void)
-{
- armadillo5x0_smc911x_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
- armadillo5x0_smc911x_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- imx_add_gpio_keys(&armadillo5x0_button_data);
-
- /* SMSC9118 IRQ pin */
- gpio_direction_input(MX31_PIN_GPIO1_0);
-
- /* Register SDHC */
- imx31_add_mxc_mmc(0, &sdhc_pdata);
-
- /* RTC */
- /* Get RTC IRQ and register the chip */
- if (!gpio_request(ARMADILLO5X0_RTC_GPIO, "rtc")) {
- if (!gpio_direction_input(ARMADILLO5X0_RTC_GPIO))
- armadillo5x0_i2c_rtc.irq =
- gpio_to_irq(ARMADILLO5X0_RTC_GPIO);
- else
- gpio_free(ARMADILLO5X0_RTC_GPIO);
- }
-
- if (armadillo5x0_i2c_rtc.irq == 0)
- pr_warn("armadillo5x0_init: failed to get RTC IRQ\n");
- i2c_register_board_info(1, &armadillo5x0_i2c_rtc, 1);
-
- /* USB */
- usbotg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbotg_pdata.otg)
- imx31_add_mxc_ehci_otg(&usbotg_pdata);
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbh2_pdata.otg)
- imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static void __init armadillo5x0_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(ARMADILLO5X0, "Armadillo-500")
- /* Maintainer: Alberto Panizzo */
- .atag_offset = 0x100,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = armadillo5x0_timer_init,
- .init_machine = armadillo5x0_init,
- .init_late = armadillo5x0_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-bug.c b/arch/arm/mach-imx/mach-bug.c
deleted file mode 100644
index 3929208..0000000
--- a/arch/arm/mach-imx/mach-bug.c
+++ /dev/null
@@ -1,54 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2011 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const unsigned int bug_pins[] __initconst = {
- MX31_PIN_PC_RST__CTS5,
- MX31_PIN_PC_VS2__RTS5,
- MX31_PIN_PC_BVD2__TXD5,
- MX31_PIN_PC_BVD1__RXD5,
-};
-
-static void __init bug_board_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(bug_pins,
- ARRAY_SIZE(bug_pins), "uart-4");
- imx31_add_imx_uart4(&uart_pdata);
-}
-
-static void __init bug_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(BUG, "BugLabs BUGBase")
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = bug_timer_init,
- .init_machine = bug_board_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-imx27.c b/arch/arm/mach-imx/mach-imx27.c
new file mode 100644
index 0000000..262422a
--- /dev/null
+++ b/arch/arm/mach-imx/mach-imx27.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/mm.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+
+#include "common.h"
+#include "hardware.h"
+#include "mx27.h"
+
+/* MX27 memory map definition */
+static struct map_desc imx27_io_desc[] __initdata = {
+ /*
+ * this fixed mapping covers:
+ * - AIPI1
+ * - AIPI2
+ * - AITC
+ * - ROM Patch
+ * - and some reserved space
+ */
+ imx_map_entry(MX27, AIPI, MT_DEVICE),
+ /*
+ * this fixed mapping covers:
+ * - CSI
+ * - ATA
+ */
+ imx_map_entry(MX27, SAHB1, MT_DEVICE),
+ /*
+ * this fixed mapping covers:
+ * - EMI
+ */
+ imx_map_entry(MX27, X_MEMC, MT_DEVICE),
+};
+
+/*
+ * Initialize the memory map. It is called during the
+ * system startup to create static physical to virtual
+ * memory map for the IO modules.
+ */
+static void __init mx27_map_io(void)
+{
+ iotable_init(imx27_io_desc, ARRAY_SIZE(imx27_io_desc));
+}
+
+static void __init imx27_init_early(void)
+{
+ mxc_set_cpu_type(MXC_CPU_MX27);
+}
+
+static void __init mx27_init_irq(void)
+{
+ void __iomem *avic_base;
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,avic");
+ avic_base = of_iomap(np, 0);
+ BUG_ON(!avic_base);
+ mxc_init_irq(avic_base);
+}
+
+static const char * const imx27_dt_board_compat[] __initconst = {
+ "fsl,imx27",
+ NULL
+};
+
+DT_MACHINE_START(IMX27_DT, "Freescale i.MX27 (Device Tree Support)")
+ .map_io = mx27_map_io,
+ .init_early = imx27_init_early,
+ .init_irq = mx27_init_irq,
+ .init_late = imx27_pm_init,
+ .dt_compat = imx27_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
deleted file mode 100644
index a329e50..0000000
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ /dev/null
@@ -1,562 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * mach-imx27_visstrim_m10.c
- *
- * Copyright 2010 Javier Martin <javier.martin@vista-silicon.com>
- *
- * Based on mach-pcm038.c, mach-pca100.c, mach-mx27ads.c and others.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/pca953x.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/dma-map-ops.h>
-#include <linux/leds.h>
-#include <linux/platform_data/asoc-mx27vis.h>
-#include <sound/tlv320aic32x4.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/system_info.h>
-#include <asm/memblock.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-#define TVP5150_RSTN (GPIO_PORTC + 18)
-#define TVP5150_PWDN (GPIO_PORTC + 19)
-#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
-#define SDHC1_IRQ_GPIO IMX_GPIO_NR(2, 25)
-
-#define VERSION_MASK 0x7
-#define MOTHERBOARD_SHIFT 4
-#define EXPBOARD_SHIFT 0
-
-#define MOTHERBOARD_BIT2 (GPIO_PORTD + 31)
-#define MOTHERBOARD_BIT1 (GPIO_PORTD + 30)
-#define MOTHERBOARD_BIT0 (GPIO_PORTD + 29)
-
-#define EXPBOARD_BIT2 (GPIO_PORTD + 25)
-#define EXPBOARD_BIT1 (GPIO_PORTD + 27)
-#define EXPBOARD_BIT0 (GPIO_PORTD + 28)
-
-#define AMP_GAIN_0 (GPIO_PORTF + 9)
-#define AMP_GAIN_1 (GPIO_PORTF + 8)
-#define AMP_MUTE_SDL (GPIO_PORTE + 5)
-#define AMP_MUTE_SDR (GPIO_PORTF + 7)
-
-static const int visstrim_m10_pins[] __initconst = {
- /* UART1 (console) */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS,
- /* FEC */
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_RX_CLK,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN,
- /* SSI1 */
- PC20_PF_SSI1_FS,
- PC21_PF_SSI1_RXD,
- PC22_PF_SSI1_TXD,
- PC23_PF_SSI1_CLK,
- /* SDHC1 */
- PE18_PF_SD1_D0,
- PE19_PF_SD1_D1,
- PE20_PF_SD1_D2,
- PE21_PF_SD1_D3,
- PE22_PF_SD1_CMD,
- PE23_PF_SD1_CLK,
- /* Both I2Cs */
- PD17_PF_I2C_DATA,
- PD18_PF_I2C_CLK,
- PC5_PF_I2C2_SDA,
- PC6_PF_I2C2_SCL,
- /* USB OTG */
- OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
- PC9_PF_USBOTG_DATA0,
- PC11_PF_USBOTG_DATA1,
- PC10_PF_USBOTG_DATA2,
- PC13_PF_USBOTG_DATA3,
- PC12_PF_USBOTG_DATA4,
- PC7_PF_USBOTG_DATA5,
- PC8_PF_USBOTG_DATA6,
- PE25_PF_USBOTG_DATA7,
- PE24_PF_USBOTG_CLK,
- PE2_PF_USBOTG_DIR,
- PE0_PF_USBOTG_NXT,
- PE1_PF_USBOTG_STP,
- PB23_PF_USB_PWR,
- PB24_PF_USB_OC,
- /* CSI */
- TVP5150_RSTN | GPIO_GPIO | GPIO_OUT,
- TVP5150_PWDN | GPIO_GPIO | GPIO_OUT,
- PB10_PF_CSI_D0,
- PB11_PF_CSI_D1,
- PB12_PF_CSI_D2,
- PB13_PF_CSI_D3,
- PB14_PF_CSI_D4,
- PB15_PF_CSI_MCLK,
- PB16_PF_CSI_PIXCLK,
- PB17_PF_CSI_D5,
- PB18_PF_CSI_D6,
- PB19_PF_CSI_D7,
- PB20_PF_CSI_VSYNC,
- PB21_PF_CSI_HSYNC,
- /* mother board version */
- MOTHERBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- MOTHERBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- MOTHERBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- /* expansion board version */
- EXPBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- EXPBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- EXPBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
- /* Audio AMP control */
- AMP_GAIN_0 | GPIO_GPIO | GPIO_OUT,
- AMP_GAIN_1 | GPIO_GPIO | GPIO_OUT,
- AMP_MUTE_SDL | GPIO_GPIO | GPIO_OUT,
- AMP_MUTE_SDR | GPIO_GPIO | GPIO_OUT,
-};
-
-static struct gpio visstrim_m10_version_gpios[] = {
- { EXPBOARD_BIT0, GPIOF_IN, "exp-version-0" },
- { EXPBOARD_BIT1, GPIOF_IN, "exp-version-1" },
- { EXPBOARD_BIT2, GPIOF_IN, "exp-version-2" },
- { MOTHERBOARD_BIT0, GPIOF_IN, "mother-version-0" },
- { MOTHERBOARD_BIT1, GPIOF_IN, "mother-version-1" },
- { MOTHERBOARD_BIT2, GPIOF_IN, "mother-version-2" },
-};
-
-static const struct gpio visstrim_m10_gpios[] __initconst = {
- {
- .gpio = TVP5150_RSTN,
- .flags = GPIOF_DIR_OUT | GPIOF_INIT_HIGH,
- .label = "tvp5150_rstn",
- },
- {
- .gpio = TVP5150_PWDN,
- .flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
- .label = "tvp5150_pwdn",
- },
- {
- .gpio = OTG_PHY_CS_GPIO,
- .flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
- .label = "usbotg_cs",
- },
- {
- .gpio = AMP_GAIN_0,
- .flags = GPIOF_DIR_OUT,
- .label = "amp-gain-0",
- },
- {
- .gpio = AMP_GAIN_1,
- .flags = GPIOF_DIR_OUT,
- .label = "amp-gain-1",
- },
- {
- .gpio = AMP_MUTE_SDL,
- .flags = GPIOF_DIR_OUT,
- .label = "amp-mute-sdl",
- },
- {
- .gpio = AMP_MUTE_SDR,
- .flags = GPIOF_DIR_OUT,
- .label = "amp-mute-sdr",
- },
-};
-
-/* Camera */
-static struct mx2_camera_platform_data visstrim_camera = {
- .flags = MX2_CAMERA_CCIR | MX2_CAMERA_CCIR_INTERLACE |
- MX2_CAMERA_PCLK_SAMPLE_RISING,
- .clk = 100000,
-};
-
-static phys_addr_t mx2_camera_base __initdata;
-#define MX2_CAMERA_BUF_SIZE SZ_8M
-
-static void __init visstrim_analog_camera_init(void)
-{
- struct platform_device *pdev;
-
- gpio_set_value(TVP5150_PWDN, 1);
- ndelay(1);
- gpio_set_value(TVP5150_RSTN, 0);
- ndelay(500);
- gpio_set_value(TVP5150_RSTN, 1);
- ndelay(200000);
-
- pdev = imx27_add_mx2_camera(&visstrim_camera);
- if (IS_ERR(pdev))
- return;
-
- dma_declare_coherent_memory(&pdev->dev, mx2_camera_base,
- mx2_camera_base, MX2_CAMERA_BUF_SIZE);
-}
-
-static void __init visstrim_reserve(void)
-{
- /* reserve 4 MiB for mx2-camera */
- mx2_camera_base = arm_memblock_steal(3 * MX2_CAMERA_BUF_SIZE,
- MX2_CAMERA_BUF_SIZE);
-}
-
-/* GPIOs used as events for applications */
-static struct gpio_keys_button visstrim_gpio_keys[] = {
- {
- .type = EV_KEY,
- .code = KEY_RESTART,
- .gpio = (GPIO_PORTC + 15),
- .desc = "Default config",
- .active_low = 0,
- .wakeup = 1,
- },
- {
- .type = EV_KEY,
- .code = KEY_RECORD,
- .gpio = (GPIO_PORTF + 14),
- .desc = "Record",
- .active_low = 0,
- .wakeup = 1,
- },
- {
- .type = EV_KEY,
- .code = KEY_STOP,
- .gpio = (GPIO_PORTF + 13),
- .desc = "Stop",
- .active_low = 0,
- .wakeup = 1,
- }
-};
-
-static const struct gpio_keys_platform_data
- visstrim_gpio_keys_platform_data __initconst = {
- .buttons = visstrim_gpio_keys,
- .nbuttons = ARRAY_SIZE(visstrim_gpio_keys),
-};
-
-/* led */
-static const struct gpio_led visstrim_m10_leds[] __initconst = {
- {
- .name = "visstrim:ld0",
- .default_trigger = "nand-disk",
- .gpio = (GPIO_PORTC + 29),
- },
- {
- .name = "visstrim:ld1",
- .default_trigger = "nand-disk",
- .gpio = (GPIO_PORTC + 24),
- },
- {
- .name = "visstrim:ld2",
- .default_trigger = "nand-disk",
- .gpio = (GPIO_PORTC + 28),
- },
- {
- .name = "visstrim:ld3",
- .default_trigger = "nand-disk",
- .gpio = (GPIO_PORTC + 25),
- },
-};
-
-static const struct gpio_led_platform_data visstrim_m10_led_data __initconst = {
- .leds = visstrim_m10_leds,
- .num_leds = ARRAY_SIZE(visstrim_m10_leds),
-};
-
-/* Visstrim_SM10 has a microSD slot connected to sdhc1 */
-static int visstrim_m10_sdhc1_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
-{
- int ret;
-
- ret = request_irq(gpio_to_irq(SDHC1_IRQ_GPIO), detect_irq,
- IRQF_TRIGGER_FALLING, "mmc-detect", data);
- return ret;
-}
-
-static void visstrim_m10_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(SDHC1_IRQ_GPIO), data);
-}
-
-static const struct imxmmc_platform_data visstrim_m10_sdhc_pdata __initconst = {
- .init = visstrim_m10_sdhc1_init,
- .exit = visstrim_m10_sdhc1_exit,
-};
-
-/* Visstrim_SM10 NOR flash */
-static struct physmap_flash_data visstrim_m10_flash_data = {
- .width = 2,
-};
-
-static struct resource visstrim_m10_flash_resource = {
- .start = 0xc0000000,
- .end = 0xc0000000 + SZ_64M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device visstrim_m10_nor_mtd_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &visstrim_m10_flash_data,
- },
- .num_resources = 1,
- .resource = &visstrim_m10_flash_resource,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
- &visstrim_m10_nor_mtd_device,
-};
-
-/* Visstrim_M10 uses UART0 as console */
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-/* I2C */
-static const struct imxi2c_platform_data visstrim_m10_i2c_data __initconst = {
- .bitrate = 100000,
-};
-
-static struct pca953x_platform_data visstrim_m10_pca9555_pdata = {
- .gpio_base = 240, /* After MX27 internal GPIOs */
- .invert = 0,
-};
-
-static struct aic32x4_pdata visstrim_m10_aic32x4_pdata = {
- .power_cfg = AIC32X4_PWR_MICBIAS_2075_LDOIN |
- AIC32X4_PWR_AVDD_DVDD_WEAK_DISABLE |
- AIC32X4_PWR_AIC32X4_LDO_ENABLE |
- AIC32X4_PWR_CMMODE_LDOIN_RANGE_18_36 |
- AIC32X4_PWR_CMMODE_HP_LDOIN_POWERED,
- .micpga_routing = AIC32X4_MICPGA_ROUTE_LMIC_IN2R_10K |
- AIC32X4_MICPGA_ROUTE_RMIC_IN1L_10K,
- .swapdacs = false,
-};
-
-static struct i2c_board_info visstrim_m10_i2c_devices[] = {
- {
- I2C_BOARD_INFO("pca9555", 0x20),
- .platform_data = &visstrim_m10_pca9555_pdata,
- },
- {
- I2C_BOARD_INFO("tlv320aic32x4", 0x18),
- .platform_data = &visstrim_m10_aic32x4_pdata,
- },
- {
- I2C_BOARD_INFO("m41t00", 0x68),
- }
-};
-
-/* USB OTG */
-static int otg_phy_init(struct platform_device *pdev)
-{
- return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static const struct mxc_usbh_platform_data
-visstrim_m10_usbotg_pdata __initconst = {
- .init = otg_phy_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/* SSI */
-static const struct imx_ssi_platform_data visstrim_m10_ssi_pdata __initconst = {
- .flags = IMX_SSI_DMA | IMX_SSI_SYN,
-};
-
-/* coda */
-
-static void __init visstrim_coda_init(void)
-{
- struct platform_device *pdev;
-
- pdev = imx27_add_coda();
- dma_declare_coherent_memory(&pdev->dev,
- mx2_camera_base + MX2_CAMERA_BUF_SIZE,
- mx2_camera_base + MX2_CAMERA_BUF_SIZE,
- MX2_CAMERA_BUF_SIZE);
-}
-
-/* DMA deinterlace */
-static struct platform_device visstrim_deinterlace = {
- .name = "m2m-deinterlace",
- .id = 0,
-};
-
-static void __init visstrim_deinterlace_init(void)
-{
- int ret = -ENOMEM;
- struct platform_device *pdev = &visstrim_deinterlace;
-
- ret = platform_device_register(pdev);
-
- dma_declare_coherent_memory(&pdev->dev,
- mx2_camera_base + 2 * MX2_CAMERA_BUF_SIZE,
- mx2_camera_base + 2 * MX2_CAMERA_BUF_SIZE,
- MX2_CAMERA_BUF_SIZE);
-}
-
-/* Emma-PrP for format conversion */
-static void __init visstrim_emmaprp_init(void)
-{
- struct platform_device *pdev;
- int ret;
-
- pdev = imx27_add_mx2_emmaprp();
- if (IS_ERR(pdev))
- return;
-
- /*
- * Use the same memory area as the analog camera since both
- * devices are, by nature, exclusive.
- */
- ret = dma_declare_coherent_memory(&pdev->dev,
- mx2_camera_base, mx2_camera_base,
- MX2_CAMERA_BUF_SIZE);
- if (ret)
- pr_err("Failed to declare memory for emmaprp\n");
-}
-
-/* Audio */
-static const struct snd_mx27vis_platform_data snd_mx27vis_pdata __initconst = {
- .amp_gain0_gpio = AMP_GAIN_0,
- .amp_gain1_gpio = AMP_GAIN_1,
- .amp_mutel_gpio = AMP_MUTE_SDL,
- .amp_muter_gpio = AMP_MUTE_SDR,
-};
-
-static void __init visstrim_m10_revision(void)
-{
- int exp_version = 0;
- int mo_version = 0;
- int ret;
-
- ret = gpio_request_array(visstrim_m10_version_gpios,
- ARRAY_SIZE(visstrim_m10_version_gpios));
- if (ret) {
- pr_err("Failed to request version gpios");
- return;
- }
-
- /* Get expansion board version (negative logic) */
- exp_version |= !gpio_get_value(EXPBOARD_BIT2) << 2;
- exp_version |= !gpio_get_value(EXPBOARD_BIT1) << 1;
- exp_version |= !gpio_get_value(EXPBOARD_BIT0);
-
- /* Get mother board version (negative logic) */
- mo_version |= !gpio_get_value(MOTHERBOARD_BIT2) << 2;
- mo_version |= !gpio_get_value(MOTHERBOARD_BIT1) << 1;
- mo_version |= !gpio_get_value(MOTHERBOARD_BIT0);
-
- system_rev = 0x27000;
- system_rev |= (mo_version << MOTHERBOARD_SHIFT);
- system_rev |= (exp_version << EXPBOARD_SHIFT);
-}
-
-static void __init visstrim_m10_board_init(void)
-{
- int ret;
-
- imx27_soc_init();
- visstrim_m10_revision();
-
- ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins,
- ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10");
- if (ret)
- pr_err("Failed to setup pins (%d)\n", ret);
-
- imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
- imx27_add_imx_uart0(&uart_pdata);
-
- imx27_add_imx_i2c(0, &visstrim_m10_i2c_data);
- imx27_add_imx_i2c(1, &visstrim_m10_i2c_data);
- i2c_register_board_info(0, visstrim_m10_i2c_devices,
- ARRAY_SIZE(visstrim_m10_i2c_devices));
-
- imx27_add_mxc_mmc(0, &visstrim_m10_sdhc_pdata);
- imx27_add_mxc_ehci_otg(&visstrim_m10_usbotg_pdata);
- imx27_add_fec(NULL);
-
- platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-}
-
-static void __init visstrim_m10_late_init(void)
-{
- int mo_version, ret;
-
- ret = gpio_request_array(visstrim_m10_gpios,
- ARRAY_SIZE(visstrim_m10_gpios));
- if (ret)
- pr_err("Failed to request gpios (%d)\n", ret);
-
- imx_add_gpio_keys(&visstrim_gpio_keys_platform_data);
-
- imx_add_platform_device("mx27vis", 0, NULL, 0, &snd_mx27vis_pdata,
- sizeof(snd_mx27vis_pdata));
-
- gpio_led_register_device(0, &visstrim_m10_led_data);
-
- /* Use mother board version to decide what video devices we shall use */
- mo_version = (system_rev >> MOTHERBOARD_SHIFT) & VERSION_MASK;
- if (mo_version & 0x1) {
- visstrim_emmaprp_init();
-
- /*
- * Despite not being used, tvp5150 must be
- * powered on to avoid I2C problems. To minimize
- * power consupmtion keep reset enabled.
- */
- gpio_set_value(TVP5150_PWDN, 1);
- ndelay(1);
- gpio_set_value(TVP5150_RSTN, 0);
- } else {
- visstrim_deinterlace_init();
- visstrim_analog_camera_init();
- }
-
- visstrim_coda_init();
-}
-
-static void __init visstrim_m10_timer_init(void)
-{
- mx27_clocks_init((unsigned long)25000000);
-}
-
-MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
- .atag_offset = 0x100,
- .reserve = visstrim_reserve,
- .map_io = mx27_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_time = visstrim_m10_timer_init,
- .init_machine = visstrim_m10_board_init,
- .init_late = visstrim_m10_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/imx31-dt.c b/arch/arm/mach-imx/mach-imx31.c
similarity index 100%
rename from arch/arm/mach-imx/imx31-dt.c
rename to arch/arm/mach-imx/mach-imx31.c
diff --git a/arch/arm/mach-imx/imx35-dt.c b/arch/arm/mach-imx/mach-imx35.c
similarity index 100%
rename from arch/arm/mach-imx/imx35-dt.c
rename to arch/arm/mach-imx/mach-imx35.c
diff --git a/arch/arm/mach-imx/mach-imx7ulp.c b/arch/arm/mach-imx/mach-imx7ulp.c
index 128cf4c..445256e 100644
--- a/arch/arm/mach-imx/mach-imx7ulp.c
+++ b/arch/arm/mach-imx/mach-imx7ulp.c
@@ -67,6 +67,9 @@ static const char *const imx7ulp_dt_compat[] __initconst = {
static void __init imx7ulp_init_late(void)
{
+ if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+ platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+
imx7ulp_cpuidle_init();
}
diff --git a/arch/arm/mach-imx/mach-kzm_arm11_01.c b/arch/arm/mach-imx/mach-kzm_arm11_01.c
deleted file mode 100644
index 63f7f78..0000000
--- a/arch/arm/mach-imx/mach-kzm_arm11_01.c
+++ /dev/null
@@ -1,291 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * KZM-ARM11-01 support
- * Copyright (C) 2009 Yoichi Yuasa <yuasa@linux-mips.org>
- *
- * based on code for MX31ADS,
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/smsc911x.h>
-#include <linux/types.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <asm/memory.h>
-#include <asm/setup.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-#define KZM_ARM11_IO_ADDRESS(x) (IOMEM( \
- IMX_IO_P2V_MODULE(x, MX31_CS4) ?: \
- IMX_IO_P2V_MODULE(x, MX31_CS5)) ?: \
- MX31_IO_ADDRESS(x))
-
-/*
- * KZM-ARM11-01 Board Control Registers on FPGA
- */
-#define KZM_ARM11_CTL1 (MX31_CS4_BASE_ADDR + 0x1000)
-#define KZM_ARM11_CTL2 (MX31_CS4_BASE_ADDR + 0x1001)
-#define KZM_ARM11_RSW1 (MX31_CS4_BASE_ADDR + 0x1002)
-#define KZM_ARM11_BACK_LIGHT (MX31_CS4_BASE_ADDR + 0x1004)
-#define KZM_ARM11_FPGA_REV (MX31_CS4_BASE_ADDR + 0x1008)
-#define KZM_ARM11_7SEG_LED (MX31_CS4_BASE_ADDR + 0x1010)
-#define KZM_ARM11_LEDS (MX31_CS4_BASE_ADDR + 0x1020)
-#define KZM_ARM11_DIPSW2 (MX31_CS4_BASE_ADDR + 0x1003)
-
-/*
- * External UART for touch panel on FPGA
- */
-#define KZM_ARM11_16550 (MX31_CS4_BASE_ADDR + 0x1050)
-
-#if IS_ENABLED(CONFIG_SERIAL_8250)
-/*
- * KZM-ARM11-01 has an external UART on FPGA
- */
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .membase = KZM_ARM11_IO_ADDRESS(KZM_ARM11_16550),
- .mapbase = KZM_ARM11_16550,
- /* irq number is run-time assigned */
- .irqflags = IRQ_TYPE_EDGE_RISING,
- .uartclk = 14745600,
- .regshift = 0,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
- UPF_BUGGY_UART,
- },
- {},
-};
-
-static struct resource serial8250_resources[] = {
- {
- .start = KZM_ARM11_16550,
- .end = KZM_ARM11_16550 + 0x10,
- .flags = IORESOURCE_MEM,
- },
- {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
- },
- .num_resources = ARRAY_SIZE(serial8250_resources),
- .resource = serial8250_resources,
-};
-
-static int __init kzm_init_ext_uart(void)
-{
- u8 tmp;
-
- /*
- * GPIO 1-1: external UART interrupt line
- */
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO));
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "ext-uart-int");
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
- /*
- * Unmask UART interrupt
- */
- tmp = __raw_readb(KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));
- tmp |= 0x2;
- __raw_writeb(tmp, KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));
-
- serial_platform_data[0].irq =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
- serial8250_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
- serial8250_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
- return platform_device_register(&serial_device);
-}
-#else
-static inline int kzm_init_ext_uart(void)
-{
- return 0;
-}
-#endif
-
-/*
- * SMSC LAN9118
- */
-#if IS_ENABLED(CONFIG_SMSC911X)
-static struct smsc911x_platform_config kzm_smsc9118_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct resource kzm_smsc9118_resources[] = {
- {
- .start = MX31_CS5_BASE_ADDR,
- .end = MX31_CS5_BASE_ADDR + SZ_128K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct platform_device kzm_smsc9118_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(kzm_smsc9118_resources),
- .resource = kzm_smsc9118_resources,
- .dev = {
- .platform_data = &kzm_smsc9118_config,
- },
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static int __init kzm_init_smsc9118(void)
-{
- /*
- * GPIO 1-2: SMSC9118 interrupt line
- */
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_2, IOMUX_CONFIG_GPIO));
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2), "smsc9118-int");
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- kzm_smsc9118_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
- kzm_smsc9118_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
-
- return platform_device_register(&kzm_smsc9118_device);
-}
-#else
-static inline int kzm_init_smsc9118(void)
-{
- return 0;
-}
-#endif
-
-#if IS_ENABLED(CONFIG_SERIAL_IMX)
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static void __init kzm_init_imx_uart(void)
-{
- imx31_add_imx_uart0(&uart_pdata);
- imx31_add_imx_uart1(&uart_pdata);
-}
-#else
-static inline void kzm_init_imx_uart(void)
-{
-}
-#endif
-
-static int kzm_pins[] __initdata = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
- MX31_PIN_DCD_DCE1__DCD_DCE1,
- MX31_PIN_RI_DCE1__RI_DCE1,
- MX31_PIN_DSR_DCE1__DSR_DCE1,
- MX31_PIN_DTR_DCE1__DTR_DCE1,
- MX31_PIN_CTS2__CTS2,
- MX31_PIN_RTS2__RTS2,
- MX31_PIN_TXD2__TXD2,
- MX31_PIN_RXD2__RXD2,
- MX31_PIN_DCD_DTE1__DCD_DTE2,
- MX31_PIN_RI_DTE1__RI_DTE2,
- MX31_PIN_DSR_DTE1__DSR_DTE2,
- MX31_PIN_DTR_DTE1__DTR_DTE2,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init kzm_board_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(kzm_pins,
- ARRAY_SIZE(kzm_pins), "kzm");
- kzm_init_imx_uart();
-
- pr_info("Clock input source is 26MHz\n");
-}
-
-static void __init kzm_late_init(void)
-{
- kzm_init_ext_uart();
- kzm_init_smsc9118();
-}
-
-/*
- * This structure defines static mappings for the kzm-arm11-01 board.
- */
-static struct map_desc kzm_io_desc[] __initdata = {
- {
- .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
- .length = MX31_CS4_SIZE,
- .type = MT_DEVICE
- },
- {
- .virtual = (unsigned long)MX31_CS5_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
- .length = MX31_CS5_SIZE,
- .type = MT_DEVICE
- },
-};
-
-/*
- * Set up static virtual mappings.
- */
-static void __init kzm_map_io(void)
-{
- mx31_map_io();
- iotable_init(kzm_io_desc, ARRAY_SIZE(kzm_io_desc));
-}
-
-static void __init kzm_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(KZM_ARM11_01, "Kyoto Microcomputer Co., Ltd. KZM-ARM11-01")
- .atag_offset = 0x100,
- .map_io = kzm_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = kzm_timer_init,
- .init_machine = kzm_board_init,
- .init_late = kzm_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
deleted file mode 100644
index ec011e8..0000000
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ /dev/null
@@ -1,338 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/physmap.h>
-#include <linux/gpio/driver.h>
-#include <linux/gpio/machine.h>
-#include <linux/gpio.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx21.h"
-#include "hardware.h"
-#include "iomux-mx21.h"
-
-#define MX21ADS_CS8900A_REG (MX21_CS1_BASE_ADDR + 0x000000)
-#define MX21ADS_ST16C255_IOBASE_REG (MX21_CS1_BASE_ADDR + 0x200000)
-#define MX21ADS_VERSION_REG (MX21_CS1_BASE_ADDR + 0x400000)
-#define MX21ADS_IO_REG (MX21_CS1_BASE_ADDR + 0x800000)
-
-#define MX21ADS_MMC_CD IMX_GPIO_NR(4, 25)
-#define MX21ADS_CS8900A_IRQ_GPIO IMX_GPIO_NR(5, 11)
-#define MX21ADS_MMGPIO_BASE (6 * 32)
-
-/* MX21ADS_IO_REG bit definitions */
-#define MX21ADS_IO_SD_WP (MX21ADS_MMGPIO_BASE + 0)
-#define MX21ADS_IO_TP6 (MX21ADS_IO_SD_WP)
-#define MX21ADS_IO_SW_SEL (MX21ADS_MMGPIO_BASE + 1)
-#define MX21ADS_IO_TP7 (MX21ADS_IO_SW_SEL)
-#define MX21ADS_IO_RESET_E_UART (MX21ADS_MMGPIO_BASE + 2)
-#define MX21ADS_IO_RESET_BASE (MX21ADS_MMGPIO_BASE + 3)
-#define MX21ADS_IO_CSI_CTL2 (MX21ADS_MMGPIO_BASE + 4)
-#define MX21ADS_IO_CSI_CTL1 (MX21ADS_MMGPIO_BASE + 5)
-#define MX21ADS_IO_CSI_CTL0 (MX21ADS_MMGPIO_BASE + 6)
-#define MX21ADS_IO_UART1_EN (MX21ADS_MMGPIO_BASE + 7)
-#define MX21ADS_IO_UART4_EN (MX21ADS_MMGPIO_BASE + 8)
-#define MX21ADS_IO_LCDON (MX21ADS_MMGPIO_BASE + 9)
-#define MX21ADS_IO_IRDA_EN (MX21ADS_MMGPIO_BASE + 10)
-#define MX21ADS_IO_IRDA_FIR_SEL (MX21ADS_MMGPIO_BASE + 11)
-#define MX21ADS_IO_IRDA_MD0_B (MX21ADS_MMGPIO_BASE + 12)
-#define MX21ADS_IO_IRDA_MD1 (MX21ADS_MMGPIO_BASE + 13)
-#define MX21ADS_IO_LED4_ON (MX21ADS_MMGPIO_BASE + 14)
-#define MX21ADS_IO_LED3_ON (MX21ADS_MMGPIO_BASE + 15)
-
-static const int mx21ads_pins[] __initconst = {
-
- /* CS8900A */
- (GPIO_PORTE | GPIO_GPIO | GPIO_IN | 11),
-
- /* UART1 */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS,
-
- /* UART3 (IrDA) - only TXD and RXD */
- PE8_PF_UART3_TXD,
- PE9_PF_UART3_RXD,
-
- /* UART4 */
- PB26_AF_UART4_RTS,
- PB28_AF_UART4_TXD,
- PB29_AF_UART4_CTS,
- PB31_AF_UART4_RXD,
-
- /* LCDC */
- PA5_PF_LSCLK,
- PA6_PF_LD0,
- PA7_PF_LD1,
- PA8_PF_LD2,
- PA9_PF_LD3,
- PA10_PF_LD4,
- PA11_PF_LD5,
- PA12_PF_LD6,
- PA13_PF_LD7,
- PA14_PF_LD8,
- PA15_PF_LD9,
- PA16_PF_LD10,
- PA17_PF_LD11,
- PA18_PF_LD12,
- PA19_PF_LD13,
- PA20_PF_LD14,
- PA21_PF_LD15,
- PA22_PF_LD16,
- PA24_PF_REV, /* Sharp panel dedicated signal */
- PA25_PF_CLS, /* Sharp panel dedicated signal */
- PA26_PF_PS, /* Sharp panel dedicated signal */
- PA27_PF_SPL_SPR, /* Sharp panel dedicated signal */
- PA28_PF_HSYNC,
- PA29_PF_VSYNC,
- PA30_PF_CONTRAST,
- PA31_PF_OE_ACD,
-
- /* MMC/SDHC */
- PE18_PF_SD1_D0,
- PE19_PF_SD1_D1,
- PE20_PF_SD1_D2,
- PE21_PF_SD1_D3,
- PE22_PF_SD1_CMD,
- PE23_PF_SD1_CLK,
-
- /* NFC */
- PF0_PF_NRFB,
- PF1_PF_NFCE,
- PF2_PF_NFWP,
- PF3_PF_NFCLE,
- PF4_PF_NFALE,
- PF5_PF_NFRE,
- PF6_PF_NFWE,
- PF7_PF_NFIO0,
- PF8_PF_NFIO1,
- PF9_PF_NFIO2,
- PF10_PF_NFIO3,
- PF11_PF_NFIO4,
- PF12_PF_NFIO5,
- PF13_PF_NFIO6,
- PF14_PF_NFIO7,
-};
-
-/* ADS's NOR flash: 2x AM29BDS128HE9VKI on 32-bit bus */
-static struct physmap_flash_data mx21ads_flash_data = {
- .width = 4,
-};
-
-static struct resource mx21ads_flash_resource =
- DEFINE_RES_MEM(MX21_CS0_BASE_ADDR, SZ_32M);
-
-static struct platform_device mx21ads_nor_mtd_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &mx21ads_flash_data,
- },
- .num_resources = 1,
- .resource = &mx21ads_flash_resource,
-};
-
-static struct resource mx21ads_cs8900_resources[] __initdata = {
- DEFINE_RES_MEM(MX21ADS_CS8900A_REG, SZ_1K),
- /* irq number is run-time assigned */
- DEFINE_RES_IRQ(-1),
-};
-
-static const struct platform_device_info mx21ads_cs8900_devinfo __initconst = {
- .name = "cs89x0",
- .id = 0,
- .res = mx21ads_cs8900_resources,
- .num_res = ARRAY_SIZE(mx21ads_cs8900_resources),
-};
-
-static const struct imxuart_platform_data uart_pdata_rts __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxuart_platform_data uart_pdata_norts __initconst = {
-};
-
-static struct resource mx21ads_mmgpio_resource =
- DEFINE_RES_MEM_NAMED(MX21ADS_IO_REG, SZ_2, "dat");
-
-static struct bgpio_pdata mx21ads_mmgpio_pdata = {
- .label = "mx21ads-mmgpio",
- .base = MX21ADS_MMGPIO_BASE,
- .ngpio = 16,
-};
-
-static struct platform_device mx21ads_mmgpio = {
- .name = "basic-mmio-gpio",
- .id = PLATFORM_DEVID_AUTO,
- .resource = &mx21ads_mmgpio_resource,
- .num_resources = 1,
- .dev = {
- .platform_data = &mx21ads_mmgpio_pdata,
- },
-};
-
-static struct regulator_consumer_supply mx21ads_lcd_regulator_consumer =
- REGULATOR_SUPPLY("lcd", "imx-fb.0");
-
-static struct regulator_init_data mx21ads_lcd_regulator_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .consumer_supplies = &mx21ads_lcd_regulator_consumer,
- .num_consumer_supplies = 1,
-};
-
-static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = {
- .supply_name = "LCD",
- .microvolts = 3300000,
- .init_data = &mx21ads_lcd_regulator_init_data,
-};
-
-static struct platform_device mx21ads_lcd_regulator = {
- .name = "reg-fixed-voltage",
- .id = PLATFORM_DEVID_AUTO,
- .dev = {
- .platform_data = &mx21ads_lcd_regulator_pdata,
- },
-};
-
-static struct gpiod_lookup_table mx21ads_lcd_regulator_gpiod_table = {
- .dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
- .table = {
- GPIO_LOOKUP("mx21ads-mmgpio", 9, NULL, GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-/*
- * Connected is a portrait Sharp-QVGA display
- * of type: LQ035Q7DB02
- */
-static struct imx_fb_videomode mx21ads_modes[] = {
- {
- .mode = {
- .name = "Sharp-LQ035Q7",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 188679, /* in ps (5.3MHz) */
- .hsync_len = 2,
- .left_margin = 6,
- .right_margin = 16,
- .vsync_len = 1,
- .upper_margin = 8,
- .lower_margin = 10,
- },
- .pcr = 0xfb108bc7,
- .bpp = 16,
- },
-};
-
-static const struct imx_fb_platform_data mx21ads_fb_data __initconst = {
- .mode = mx21ads_modes,
- .num_modes = ARRAY_SIZE(mx21ads_modes),
-
- .pwmr = 0x00a903ff,
- .lscr1 = 0x00120300,
- .dmacr = 0x00020008,
-};
-
-static int mx21ads_sdhc_get_ro(struct device *dev)
-{
- return gpio_get_value(MX21ADS_IO_SD_WP);
-}
-
-static int mx21ads_sdhc_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request(MX21ADS_IO_SD_WP, "mmc-ro");
- if (ret)
- return ret;
-
- return request_irq(gpio_to_irq(MX21ADS_MMC_CD), detect_irq,
- IRQF_TRIGGER_FALLING, "mmc-detect", data);
-}
-
-static void mx21ads_sdhc_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(MX21ADS_MMC_CD), data);
- gpio_free(MX21ADS_IO_SD_WP);
-}
-
-static const struct imxmmc_platform_data mx21ads_sdhc_pdata __initconst = {
- .ocr_avail = MMC_VDD_29_30 | MMC_VDD_30_31, /* 3.0V */
- .get_ro = mx21ads_sdhc_get_ro,
- .init = mx21ads_sdhc_init,
- .exit = mx21ads_sdhc_exit,
-};
-
-static const struct mxc_nand_platform_data
-mx21ads_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
- &mx21ads_mmgpio,
- &mx21ads_lcd_regulator,
- &mx21ads_nor_mtd_device,
-};
-
-static void __init mx21ads_board_init(void)
-{
- imx21_soc_init();
-
- mxc_gpio_setup_multiple_pins(mx21ads_pins, ARRAY_SIZE(mx21ads_pins),
- "mx21ads");
-
- imx21_add_imx_uart0(&uart_pdata_rts);
- imx21_add_imx_uart2(&uart_pdata_norts);
- imx21_add_imx_uart3(&uart_pdata_rts);
- imx21_add_mxc_nand(&mx21ads_nand_board_info);
-
- imx21_add_imx_fb(&mx21ads_fb_data);
-}
-
-static void __init mx21ads_late_init(void)
-{
- imx21_add_mxc_mmc(0, &mx21ads_sdhc_pdata);
-
- gpiod_add_lookup_table(&mx21ads_lcd_regulator_gpiod_table);
- platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-
- mx21ads_cs8900_resources[1].start =
- gpio_to_irq(MX21ADS_CS8900A_IRQ_GPIO);
- mx21ads_cs8900_resources[1].end =
- gpio_to_irq(MX21ADS_CS8900A_IRQ_GPIO);
- platform_device_register_full(&mx21ads_cs8900_devinfo);
-}
-
-static void __init mx21ads_timer_init(void)
-{
- mx21_clocks_init(32768, 26000000);
-}
-
-MACHINE_START(MX21ADS, "Freescale i.MX21ADS")
- /* maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx21_map_io,
- .init_early = imx21_init_early,
- .init_irq = mx21_init_irq,
- .init_time = mx21ads_timer_init,
- .init_machine = mx21ads_board_init,
- .init_late = mx21ads_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
deleted file mode 100644
index 2db4475..0000000
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ /dev/null
@@ -1,470 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-/*
- * This machine is known as:
- * - i.MX27 3-Stack Development System
- * - i.MX27 Platform Development Kit (i.MX27 PDK)
- */
-
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/irq.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/delay.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-#define SD1_EN_GPIO IMX_GPIO_NR(2, 25)
-#define OTG_PHY_RESET_GPIO IMX_GPIO_NR(2, 23)
-#define SPI2_SS0 IMX_GPIO_NR(4, 21)
-#define PMIC_INT IMX_GPIO_NR(3, 14)
-#define SPI1_SS0 IMX_GPIO_NR(4, 28)
-#define SD1_CD IMX_GPIO_NR(2, 26)
-#define LCD_RESET IMX_GPIO_NR(1, 3)
-#define LCD_ENABLE IMX_GPIO_NR(1, 31)
-
-static const int mx27pdk_pins[] __initconst = {
- /* UART1 */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS,
- /* FEC */
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_RX_CLK,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN,
- /* SDHC1 */
- PE18_PF_SD1_D0,
- PE19_PF_SD1_D1,
- PE20_PF_SD1_D2,
- PE21_PF_SD1_D3,
- PE22_PF_SD1_CMD,
- PE23_PF_SD1_CLK,
- SD1_EN_GPIO | GPIO_GPIO | GPIO_OUT,
- /* OTG */
- OTG_PHY_RESET_GPIO | GPIO_GPIO | GPIO_OUT,
- PC7_PF_USBOTG_DATA5,
- PC8_PF_USBOTG_DATA6,
- PC9_PF_USBOTG_DATA0,
- PC10_PF_USBOTG_DATA2,
- PC11_PF_USBOTG_DATA1,
- PC12_PF_USBOTG_DATA4,
- PC13_PF_USBOTG_DATA3,
- PE0_PF_USBOTG_NXT,
- PE1_PF_USBOTG_STP,
- PE2_PF_USBOTG_DIR,
- PE24_PF_USBOTG_CLK,
- PE25_PF_USBOTG_DATA7,
- /* CSPI1 */
- PD31_PF_CSPI1_MOSI,
- PD30_PF_CSPI1_MISO,
- PD29_PF_CSPI1_SCLK,
- PD25_PF_CSPI1_RDY,
- SPI1_SS0 | GPIO_GPIO | GPIO_OUT,
- /* CSPI2 */
- PD22_PF_CSPI2_SCLK,
- PD23_PF_CSPI2_MISO,
- PD24_PF_CSPI2_MOSI,
- SPI2_SS0 | GPIO_GPIO | GPIO_OUT,
- /* I2C1 */
- PD17_PF_I2C_DATA,
- PD18_PF_I2C_CLK,
- /* PMIC INT */
- PMIC_INT | GPIO_GPIO | GPIO_IN,
- /* LCD */
- PA5_PF_LSCLK,
- PA6_PF_LD0,
- PA7_PF_LD1,
- PA8_PF_LD2,
- PA9_PF_LD3,
- PA10_PF_LD4,
- PA11_PF_LD5,
- PA12_PF_LD6,
- PA13_PF_LD7,
- PA14_PF_LD8,
- PA15_PF_LD9,
- PA16_PF_LD10,
- PA17_PF_LD11,
- PA18_PF_LD12,
- PA19_PF_LD13,
- PA20_PF_LD14,
- PA21_PF_LD15,
- PA22_PF_LD16,
- PA23_PF_LD17,
- PA28_PF_HSYNC,
- PA29_PF_VSYNC,
- PA30_PF_CONTRAST,
- LCD_ENABLE | GPIO_GPIO | GPIO_OUT,
- LCD_RESET | GPIO_GPIO | GPIO_OUT,
- /* SSI4 */
- PC16_PF_SSI4_FS,
- PC17_PF_SSI4_RXD,
- PC18_PF_SSI4_TXD,
- PC19_PF_SSI4_CLK,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-/*
- * Matrix keyboard
- */
-
-static const uint32_t mx27_3ds_keymap[] = {
- KEY(0, 0, KEY_UP),
- KEY(0, 1, KEY_DOWN),
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_LEFT),
- KEY(1, 2, KEY_ENTER),
- KEY(2, 0, KEY_F6),
- KEY(2, 1, KEY_F8),
- KEY(2, 2, KEY_F9),
- KEY(2, 3, KEY_F10),
-};
-
-static const struct matrix_keymap_data mx27_3ds_keymap_data __initconst = {
- .keymap = mx27_3ds_keymap,
- .keymap_size = ARRAY_SIZE(mx27_3ds_keymap),
-};
-
-static int mx27_3ds_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- return request_irq(gpio_to_irq(SD1_CD), detect_irq,
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, "sdhc1-card-detect", data);
-}
-
-static void mx27_3ds_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(SD1_CD), data);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
- .init = mx27_3ds_sdhc1_init,
- .exit = mx27_3ds_sdhc1_exit,
-};
-
-static void mx27_3ds_sdhc1_enable_level_translator(void)
-{
- /* Turn on TXB0108 OE pin */
- gpio_request(SD1_EN_GPIO, "sd1_enable");
- gpio_direction_output(SD1_EN_GPIO, 1);
-}
-
-
-static int otg_phy_init(void)
-{
- gpio_request(OTG_PHY_RESET_GPIO, "usb-otg-reset");
- gpio_direction_output(OTG_PHY_RESET_GPIO, 0);
- mdelay(1);
- gpio_set_value(OTG_PHY_RESET_GPIO, 1);
- return 0;
-}
-
-static int mx27_3ds_otg_init(struct platform_device *pdev)
-{
- return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = mx27_3ds_otg_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx27_3ds_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", mx27_3ds_otg_mode);
-
-/* Regulators */
-static struct regulator_init_data gpo_init = {
- .constraints = {
- .boot_on = 1,
- .always_on = 1,
- }
-};
-
-static struct regulator_consumer_supply vmmc1_consumers[] = {
- REGULATOR_SUPPLY("vcore", "spi0.0"),
-};
-
-static struct regulator_init_data vmmc1_init = {
- .constraints = {
- .min_uV = 2800000,
- .max_uV = 2800000,
- .apply_uV = 1,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vmmc1_consumers),
- .consumer_supplies = vmmc1_consumers,
-};
-
-static struct regulator_consumer_supply vgen_consumers[] = {
- REGULATOR_SUPPLY("vdd", "spi0.0"),
-};
-
-static struct regulator_init_data vgen_init = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(vgen_consumers),
- .consumer_supplies = vgen_consumers,
-};
-
-static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = {
- {
- .id = MC13783_REG_VMMC1,
- .init_data = &vmmc1_init,
- }, {
- .id = MC13783_REG_VGEN,
- .init_data = &vgen_init,
- }, {
- .id = MC13783_REG_GPO1, /* Turn on 1.8V */
- .init_data = &gpo_init,
- }, {
- .id = MC13783_REG_GPO3, /* Turn on 3.3V */
- .init_data = &gpo_init,
- },
-};
-
-/* MC13783 */
-static struct mc13xxx_codec_platform_data mx27_3ds_codec = {
- .dac_ssi_port = MC13783_SSI1_PORT,
- .adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data mc13783_pdata = {
- .regulators = {
- .regulators = mx27_3ds_regulators,
- .num_regulators = ARRAY_SIZE(mx27_3ds_regulators),
-
- },
- .flags = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC |
- MC13XXX_USE_CODEC,
- .codec = &mx27_3ds_codec,
-};
-
-static struct imx_ssi_platform_data mx27_3ds_ssi_pdata = {
- .flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-/* SPI */
-static struct gpiod_lookup_table mx27_spi1_gpiod_table = {
- .dev_id = "imx27-cspi.0", /* Actual device name for spi1 */
- .table = {
- /*
- * The i.MX27 has the i.MX21 GPIO controller, the SPI1 CS GPIO
- * SPI1_SS0 is numbered IMX_GPIO_NR(4, 28).
- *
- * This is in "bank 4" which is subtracted by one in the macro
- * so this is actually bank 3 on "imx21-gpio.3".
- */
- GPIO_LOOKUP_IDX("imx21-gpio.3", 28, "cs", 0, GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static struct gpiod_lookup_table mx27_spi2_gpiod_table = {
- .dev_id = "imx27-cspi.1", /* Actual device name for spi2 */
- .table = {
- /*
- * The i.MX27 has the i.MX21 GPIO controller, the SPI2 CS GPIO
- * SPI2_SS0 is numbered IMX_GPIO_NR(4, 21).
- *
- * This is in "bank 4" which is subtracted by one in the macro
- * so this is actually bank 3 on "imx21-gpio.3".
- */
- GPIO_LOOKUP_IDX("imx21-gpio.3", 21, "cs", 0, GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static struct imx_fb_videomode mx27_3ds_modes[] = {
- { /* 480x640 @ 60 Hz */
- .mode = {
- .name = "Epson-VGA",
- .refresh = 60,
- .xres = 480,
- .yres = 640,
- .pixclock = 41701,
- .left_margin = 20,
- .right_margin = 41,
- .upper_margin = 10,
- .lower_margin = 5,
- .hsync_len = 20,
- .vsync_len = 10,
- .sync = FB_SYNC_OE_ACT_HIGH |
- FB_SYNC_CLK_INVERT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
- .bpp = 16,
- .pcr = 0xFAC08B82,
- },
-};
-
-static const struct imx_fb_platform_data mx27_3ds_fb_data __initconst = {
- .mode = mx27_3ds_modes,
- .num_modes = ARRAY_SIZE(mx27_3ds_modes),
- .pwmr = 0x00A903FF,
- .lscr1 = 0x00120300,
- .dmacr = 0x00020010,
-};
-
-/* LCD */
-static struct gpiod_lookup_table mx27_3ds_lcd_gpiod_table = {
- .dev_id = "spi0.0", /* Bus 0 chipselect 0 */
- .table = {
- /*
- * The i.MX27 has the i.MX21 GPIO controller, the GPIOs
- * numbered IMX_GPIO_NR(1, 3) and IMX_GPIO_NR(1, 31)
- * are in "bank 1" which is subtracted by one in the macro
- * so these are actually bank 0 on "imx21-gpio.0".
- */
- GPIO_LOOKUP("imx21-gpio.0", 3, "reset", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("imx21-gpio.0", 31, "enable", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
- {
- .modalias = "mc13783",
- .max_speed_hz = 1000000,
- .bus_num = 1,
- .chip_select = 0, /* SS0 */
- .platform_data = &mc13783_pdata,
- /* irq number is run-time assigned */
- .mode = SPI_CS_HIGH,
- }, {
- .modalias = "l4f00242t03",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 0, /* SS0 */
- },
-};
-
-static const struct imxi2c_platform_data mx27_3ds_i2c0_data __initconst = {
- .bitrate = 100000,
-};
-
-static void __init mx27pdk_init(void)
-{
- imx27_soc_init();
-
- mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins),
- "mx27pdk");
- imx27_add_imx_uart0(&uart_pdata);
- imx27_add_fec(NULL);
- imx27_add_imx_keypad(&mx27_3ds_keymap_data);
- imx27_add_imx2_wdt();
-
- imx27_add_spi_imx1(&mx27_spi2_gpiod_table);
- imx27_add_spi_imx0(&mx27_spi1_gpiod_table);
-
- imx27_add_imx_i2c(0, &mx27_3ds_i2c0_data);
- imx27_add_imx_fb(&mx27_3ds_fb_data);
-
- imx27_add_imx_ssi(0, &mx27_3ds_ssi_pdata);
-}
-
-static void __init mx27pdk_late_init(void)
-{
- mx27_3ds_sdhc1_enable_level_translator();
- imx27_add_mxc_mmc(0, &sdhc1_pdata);
-
- otg_phy_init();
-
- if (otg_mode_host) {
- otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
-
- if (otg_pdata.otg)
- imx27_add_mxc_ehci_otg(&otg_pdata);
- }
-
- if (!otg_mode_host)
- imx27_add_fsl_usb2_udc(&otg_device_pdata);
-
- gpiod_add_lookup_table(&mx27_3ds_lcd_gpiod_table);
- mx27_3ds_spi_devs[0].irq = gpio_to_irq(PMIC_INT);
- spi_register_board_info(mx27_3ds_spi_devs,
- ARRAY_SIZE(mx27_3ds_spi_devs));
-
- if (mxc_expio_init(MX27_CS5_BASE_ADDR, IMX_GPIO_NR(3, 28)))
- pr_warn("Init of the debugboard failed, all devices on the debugboard are unusable.\n");
-
-
- imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-}
-
-static void __init mx27pdk_timer_init(void)
-{
- mx27_clocks_init(26000000);
-}
-
-MACHINE_START(MX27_3DS, "Freescale MX27PDK")
- /* maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx27_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_time = mx27pdk_timer_init,
- .init_machine = mx27pdk_init,
- .init_late = mx27pdk_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
deleted file mode 100644
index ba202f9..0000000
--- a/arch/arm/mach-imx/mach-mx27ads.c
+++ /dev/null
@@ -1,407 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-#include <linux/gpio/driver.h>
-/* Needed for gpio_to_irq() */
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-/*
- * Base address of PBC controller, CS4
- */
-#define PBC_BASE_ADDRESS 0xf4300000
-#define PBC_REG_ADDR(offset) (void __force __iomem *) \
- (PBC_BASE_ADDRESS + (offset))
-
-/* When the PBC address connection is fixed in h/w, defined as 1 */
-#define PBC_ADDR_SH 0
-
-/* Offsets for the PBC Controller register */
-/*
- * PBC Board version register offset
- */
-#define PBC_VERSION_REG PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH)
-/*
- * PBC Board control register 1 set address.
- */
-#define PBC_BCTRL1_SET_REG PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH)
-/*
- * PBC Board control register 1 clear address.
- */
-#define PBC_BCTRL1_CLEAR_REG PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH)
-
-/* PBC Board Control Register 1 bit definitions */
-#define PBC_BCTRL1_LCDON 0x0800 /* Enable the LCD */
-
-/* to determine the correct external crystal reference */
-#define CKIH_27MHZ_BIT_SET (1 << 3)
-
-static const int mx27ads_pins[] __initconst = {
- /* UART0 */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS,
- /* UART1 */
- PE3_PF_UART2_CTS,
- PE4_PF_UART2_RTS,
- PE6_PF_UART2_TXD,
- PE7_PF_UART2_RXD,
- /* UART2 */
- PE8_PF_UART3_TXD,
- PE9_PF_UART3_RXD,
- PE10_PF_UART3_CTS,
- PE11_PF_UART3_RTS,
- /* UART3 */
- PB26_AF_UART4_RTS,
- PB28_AF_UART4_TXD,
- PB29_AF_UART4_CTS,
- PB31_AF_UART4_RXD,
- /* UART4 */
- PB18_AF_UART5_TXD,
- PB19_AF_UART5_RXD,
- PB20_AF_UART5_CTS,
- PB21_AF_UART5_RTS,
- /* UART5 */
- PB10_AF_UART6_TXD,
- PB12_AF_UART6_CTS,
- PB11_AF_UART6_RXD,
- PB13_AF_UART6_RTS,
- /* FEC */
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_RX_CLK,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN,
- /* I2C2 */
- PC5_PF_I2C2_SDA,
- PC6_PF_I2C2_SCL,
- /* FB */
- PA5_PF_LSCLK,
- PA6_PF_LD0,
- PA7_PF_LD1,
- PA8_PF_LD2,
- PA9_PF_LD3,
- PA10_PF_LD4,
- PA11_PF_LD5,
- PA12_PF_LD6,
- PA13_PF_LD7,
- PA14_PF_LD8,
- PA15_PF_LD9,
- PA16_PF_LD10,
- PA17_PF_LD11,
- PA18_PF_LD12,
- PA19_PF_LD13,
- PA20_PF_LD14,
- PA21_PF_LD15,
- PA22_PF_LD16,
- PA23_PF_LD17,
- PA24_PF_REV,
- PA25_PF_CLS,
- PA26_PF_PS,
- PA27_PF_SPL_SPR,
- PA28_PF_HSYNC,
- PA29_PF_VSYNC,
- PA30_PF_CONTRAST,
- PA31_PF_OE_ACD,
- /* OWIRE */
- PE16_AF_OWIRE,
- /* SDHC1*/
- PE18_PF_SD1_D0,
- PE19_PF_SD1_D1,
- PE20_PF_SD1_D2,
- PE21_PF_SD1_D3,
- PE22_PF_SD1_CMD,
- PE23_PF_SD1_CLK,
- /* SDHC2*/
- PB4_PF_SD2_D0,
- PB5_PF_SD2_D1,
- PB6_PF_SD2_D2,
- PB7_PF_SD2_D3,
- PB8_PF_SD2_CMD,
- PB9_PF_SD2_CLK,
-};
-
-static const struct mxc_nand_platform_data
-mx27ads_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-/* ADS's NOR flash */
-static struct physmap_flash_data mx27ads_flash_data = {
- .width = 2,
-};
-
-static struct resource mx27ads_flash_resource = {
- .start = 0xc0000000,
- .end = 0xc0000000 + 0x02000000 - 1,
- .flags = IORESOURCE_MEM,
-
-};
-
-static struct platform_device mx27ads_nor_mtd_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &mx27ads_flash_data,
- },
- .num_resources = 1,
- .resource = &mx27ads_flash_resource,
-};
-
-static const struct imxi2c_platform_data mx27ads_i2c1_data __initconst = {
- .bitrate = 100000,
-};
-
-static struct i2c_board_info mx27ads_i2c_devices[] = {
-};
-
-static void vgpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- if (value)
- imx_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_SET_REG);
- else
- imx_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_CLEAR_REG);
-}
-
-static int vgpio_dir_out(struct gpio_chip *chip, unsigned offset, int value)
-{
- return 0;
-}
-
-#define MX27ADS_LCD_GPIO (6 * 32)
-
-static struct regulator_consumer_supply mx27ads_lcd_regulator_consumer =
- REGULATOR_SUPPLY("lcd", "imx-fb.0");
-
-static struct regulator_init_data mx27ads_lcd_regulator_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
-},
- .consumer_supplies = &mx27ads_lcd_regulator_consumer,
- .num_consumer_supplies = 1,
-};
-
-static struct fixed_voltage_config mx27ads_lcd_regulator_pdata = {
- .supply_name = "LCD",
- .microvolts = 3300000,
- .init_data = &mx27ads_lcd_regulator_init_data,
-};
-
-static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = {
- .dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
- .table = {
- GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static void __init mx27ads_regulator_init(void)
-{
- struct gpio_chip *vchip;
-
- vchip = kzalloc(sizeof(*vchip), GFP_KERNEL);
- vchip->owner = THIS_MODULE;
- vchip->label = "LCD";
- vchip->base = MX27ADS_LCD_GPIO;
- vchip->ngpio = 1;
- vchip->direction_output = vgpio_dir_out;
- vchip->set = vgpio_set;
- gpiochip_add_data(vchip, NULL);
-
- gpiod_add_lookup_table(&mx27ads_lcd_regulator_gpiod_table);
-
- platform_device_register_data(NULL, "reg-fixed-voltage",
- PLATFORM_DEVID_AUTO,
- &mx27ads_lcd_regulator_pdata,
- sizeof(mx27ads_lcd_regulator_pdata));
-}
-
-static struct imx_fb_videomode mx27ads_modes[] = {
- {
- .mode = {
- .name = "Sharp-LQ035Q7",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 188679, /* in ps (5.3MHz) */
- .hsync_len = 1,
- .left_margin = 9,
- .right_margin = 16,
- .vsync_len = 1,
- .upper_margin = 7,
- .lower_margin = 9,
- },
- .bpp = 16,
- .pcr = 0xFB008BC0,
- },
-};
-
-static const struct imx_fb_platform_data mx27ads_fb_data __initconst = {
- .mode = mx27ads_modes,
- .num_modes = ARRAY_SIZE(mx27ads_modes),
-
- /*
- * - HSYNC active high
- * - VSYNC active high
- * - clk notenabled while idle
- * - clock inverted
- * - data not inverted
- * - data enable low active
- * - enable sharp mode
- */
- .pwmr = 0x00A903FF,
- .lscr1 = 0x00120300,
- .dmacr = 0x00020010,
-};
-
-static int mx27ads_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- return request_irq(gpio_to_irq(IMX_GPIO_NR(5, 21)), detect_irq,
- IRQF_TRIGGER_RISING, "sdhc1-card-detect", data);
-}
-
-static int mx27ads_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- return request_irq(gpio_to_irq(IMX_GPIO_NR(2, 7)), detect_irq,
- IRQF_TRIGGER_RISING, "sdhc2-card-detect", data);
-}
-
-static void mx27ads_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IMX_GPIO_NR(5, 21)), data);
-}
-
-static void mx27ads_sdhc2_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IMX_GPIO_NR(2, 7)), data);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
- .init = mx27ads_sdhc1_init,
- .exit = mx27ads_sdhc1_exit,
-};
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
- .init = mx27ads_sdhc2_init,
- .exit = mx27ads_sdhc2_exit,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
- &mx27ads_nor_mtd_device,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static void __init mx27ads_board_init(void)
-{
- imx27_soc_init();
-
- mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins),
- "mx27ads");
-
- imx27_add_imx_uart0(&uart_pdata);
- imx27_add_imx_uart1(&uart_pdata);
- imx27_add_imx_uart2(&uart_pdata);
- imx27_add_imx_uart3(&uart_pdata);
- imx27_add_imx_uart4(&uart_pdata);
- imx27_add_imx_uart5(&uart_pdata);
- imx27_add_mxc_nand(&mx27ads_nand_board_info);
-
- /* only the i2c master 1 is used on this CPU card */
- i2c_register_board_info(1, mx27ads_i2c_devices,
- ARRAY_SIZE(mx27ads_i2c_devices));
- imx27_add_imx_i2c(1, &mx27ads_i2c1_data);
- imx27_add_imx_fb(&mx27ads_fb_data);
-
- imx27_add_fec(NULL);
- imx27_add_mxc_w1();
-}
-
-static void __init mx27ads_late_init(void)
-{
- mx27ads_regulator_init();
-
- imx27_add_mxc_mmc(0, &sdhc1_pdata);
- imx27_add_mxc_mmc(1, &sdhc2_pdata);
-
- platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-}
-
-static void __init mx27ads_timer_init(void)
-{
- unsigned long fref = 26000000;
-
- if ((imx_readw(PBC_VERSION_REG) & CKIH_27MHZ_BIT_SET) == 0)
- fref = 27000000;
-
- mx27_clocks_init(fref);
-}
-
-static struct map_desc mx27ads_io_desc[] __initdata = {
- {
- .virtual = PBC_BASE_ADDRESS,
- .pfn = __phys_to_pfn(MX27_CS4_BASE_ADDR),
- .length = SZ_1M,
- .type = MT_DEVICE,
- },
-};
-
-static void __init mx27ads_map_io(void)
-{
- mx27_map_io();
- iotable_init(mx27ads_io_desc, ARRAY_SIZE(mx27ads_io_desc));
-}
-
-MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
- /* maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx27ads_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_time = mx27ads_timer_init,
- .init_machine = mx27ads_board_init,
- .init_late = mx27ads_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
deleted file mode 100644
index 23e63d3..0000000
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ /dev/null
@@ -1,615 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/delay.h>
-#include <linux/dma-mapping.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/machine.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static int mx31_3ds_pins[] = {
- /* UART1 */
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
- IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO),
- /*SPI0*/
- IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_ALT1),
- /* SPI 1 */
- MX31_PIN_CSPI2_SCLK__SCLK,
- MX31_PIN_CSPI2_MOSI__MOSI,
- MX31_PIN_CSPI2_MISO__MISO,
- MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI2_SS0__SS0,
- MX31_PIN_CSPI2_SS2__SS2, /*CS for MC13783 */
- /* MC13783 IRQ */
- IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO),
- /* USB OTG reset */
- IOMUX_MODE(MX31_PIN_USB_PWR, IOMUX_CONFIG_GPIO),
- /* USB OTG */
- MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
- MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
- MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
- MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
- MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
- MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
- MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
- MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
- MX31_PIN_USBOTG_CLK__USBOTG_CLK,
- MX31_PIN_USBOTG_DIR__USBOTG_DIR,
- MX31_PIN_USBOTG_NXT__USBOTG_NXT,
- MX31_PIN_USBOTG_STP__USBOTG_STP,
- /*Keyboard*/
- MX31_PIN_KEY_ROW0_KEY_ROW0,
- MX31_PIN_KEY_ROW1_KEY_ROW1,
- MX31_PIN_KEY_ROW2_KEY_ROW2,
- MX31_PIN_KEY_COL0_KEY_COL0,
- MX31_PIN_KEY_COL1_KEY_COL1,
- MX31_PIN_KEY_COL2_KEY_COL2,
- MX31_PIN_KEY_COL3_KEY_COL3,
- /* USB Host 2 */
- IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_PC_VS2, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_PC_BVD1, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_PC_BVD2, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_PC_RST, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_IOIS16, IOMUX_CONFIG_ALT1),
- IOMUX_MODE(MX31_PIN_PC_RW_B, IOMUX_CONFIG_ALT1),
- /* USB Host2 reset */
- IOMUX_MODE(MX31_PIN_USB_BYP, IOMUX_CONFIG_GPIO),
- /* I2C1 */
- MX31_PIN_I2C_CLK__I2C1_SCL,
- MX31_PIN_I2C_DAT__I2C1_SDA,
- /* SDHC1 */
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
- MX31_PIN_GPIO3_1__GPIO3_1, /* Card detect */
- MX31_PIN_GPIO3_0__GPIO3_0, /* OE */
- /* Framebuffer */
- MX31_PIN_LD0__LD0,
- MX31_PIN_LD1__LD1,
- MX31_PIN_LD2__LD2,
- MX31_PIN_LD3__LD3,
- MX31_PIN_LD4__LD4,
- MX31_PIN_LD5__LD5,
- MX31_PIN_LD6__LD6,
- MX31_PIN_LD7__LD7,
- MX31_PIN_LD8__LD8,
- MX31_PIN_LD9__LD9,
- MX31_PIN_LD10__LD10,
- MX31_PIN_LD11__LD11,
- MX31_PIN_LD12__LD12,
- MX31_PIN_LD13__LD13,
- MX31_PIN_LD14__LD14,
- MX31_PIN_LD15__LD15,
- MX31_PIN_LD16__LD16,
- MX31_PIN_LD17__LD17,
- MX31_PIN_VSYNC3__VSYNC3,
- MX31_PIN_HSYNC__HSYNC,
- MX31_PIN_FPSHIFT__FPSHIFT,
- MX31_PIN_CONTRAST__CONTRAST,
- /* SSI */
- MX31_PIN_STXD4__STXD4,
- MX31_PIN_SRXD4__SRXD4,
- MX31_PIN_SCK4__SCK4,
- MX31_PIN_SFS4__SFS4,
-};
-
-/*
- * FB support
- */
-static const struct fb_videomode fb_modedb[] = {
- { /* 480x640 @ 60 Hz */
- .name = "Epson-VGA",
- .refresh = 60,
- .xres = 480,
- .yres = 640,
- .pixclock = 41701,
- .left_margin = 20,
- .right_margin = 41,
- .upper_margin = 10,
- .lower_margin = 5,
- .hsync_len = 20,
- .vsync_len = 10,
- .sync = FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "Epson-VGA",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-/* LCD */
-static struct gpiod_lookup_table mx31_3ds_lcd_gpiod_table = {
- .dev_id = "spi0.2", /* Bus 0 chipselect 2 */
- .table = {
- /*
- * "reset" has IOMUX_TO_GPIO(IOMUX_PIN(88, 28)).
- * The macro only shifts 88 to bits 9..16 and then
- * mask it and shift it back. The GPIO number is 88.
- * 88 is 2*32+24
- */
- GPIO_LOOKUP("imx31-gpio.2", 24, "reset", GPIO_ACTIVE_HIGH),
- /*
- * Same reasoning as above for
- * IOMUX_TO_GPIO(IOMUX_PIN(89, 27), pin 89 is 2*32+25.
- */
- GPIO_LOOKUP("imx31-gpio.2", 25, "enable", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-/*
- * Support for SD card slot in personality board
- */
-#define MX31_3DS_GPIO_SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)
-#define MX31_3DS_GPIO_SDHC1_BE IOMUX_TO_GPIO(MX31_PIN_GPIO3_0)
-
-static struct gpio mx31_3ds_sdhc1_gpios[] = {
- { MX31_3DS_GPIO_SDHC1_CD, GPIOF_IN, "sdhc1-card-detect" },
- { MX31_3DS_GPIO_SDHC1_BE, GPIOF_OUT_INIT_LOW, "sdhc1-bus-en" },
-};
-
-static int mx31_3ds_sdhc1_init(struct device *dev,
- irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request_array(mx31_3ds_sdhc1_gpios,
- ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
- if (ret) {
- pr_warn("Unable to request the SD/MMC GPIOs.\n");
- return ret;
- }
-
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)),
- detect_irq,
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "sdhc1-detect", data);
- if (ret) {
- pr_warn("Unable to request the SD/MMC card-detect IRQ.\n");
- goto gpio_free;
- }
-
- return 0;
-
-gpio_free:
- gpio_free_array(mx31_3ds_sdhc1_gpios,
- ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
- return ret;
-}
-
-static void mx31_3ds_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)), data);
- gpio_free_array(mx31_3ds_sdhc1_gpios,
- ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
-}
-
-static void mx31_3ds_sdhc1_setpower(struct device *dev, unsigned int vdd)
-{
- /*
- * While the voltage stuff is done by the driver, activate the
- * Buffer Enable Pin only if there is a card in slot to fix the card
- * voltage issue caused by bi-directional chip TXB0108 on 3Stack.
- * Done here because at this stage we have for sure a debounced value
- * of the presence of the card, showed by the value of vdd.
- * 7 == ilog2(MMC_VDD_165_195)
- */
- if (vdd > 7)
- gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 1);
- else
- gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 0);
-}
-
-static struct imxmmc_platform_data sdhc1_pdata = {
- .init = mx31_3ds_sdhc1_init,
- .exit = mx31_3ds_sdhc1_exit,
- .setpower = mx31_3ds_sdhc1_setpower,
-};
-
-/*
- * Matrix keyboard
- */
-
-static const uint32_t mx31_3ds_keymap[] = {
- KEY(0, 0, KEY_UP),
- KEY(0, 1, KEY_DOWN),
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_LEFT),
- KEY(1, 2, KEY_ENTER),
- KEY(2, 0, KEY_F6),
- KEY(2, 1, KEY_F8),
- KEY(2, 2, KEY_F9),
- KEY(2, 3, KEY_F10),
-};
-
-static const struct matrix_keymap_data mx31_3ds_keymap_data __initconst = {
- .keymap = mx31_3ds_keymap,
- .keymap_size = ARRAY_SIZE(mx31_3ds_keymap),
-};
-
-/* Regulators */
-static struct regulator_init_data pwgtx_init = {
- .constraints = {
- .boot_on = 1,
- .always_on = 1,
- },
-};
-
-static struct regulator_init_data gpo_init = {
- .constraints = {
- .boot_on = 1,
- .always_on = 1,
- }
-};
-
-static struct regulator_consumer_supply vmmc2_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "imx31-mmc.0"),
-};
-
-static struct regulator_init_data vmmc2_init = {
- .constraints = {
- .min_uV = 3000000,
- .max_uV = 3000000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vmmc2_consumers),
- .consumer_supplies = vmmc2_consumers,
-};
-
-static struct regulator_consumer_supply vmmc1_consumers[] = {
- REGULATOR_SUPPLY("vcore", "spi0.0"),
-};
-
-static struct regulator_init_data vmmc1_init = {
- .constraints = {
- .min_uV = 2800000,
- .max_uV = 2800000,
- .apply_uV = 1,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vmmc1_consumers),
- .consumer_supplies = vmmc1_consumers,
-};
-
-static struct regulator_consumer_supply vgen_consumers[] = {
- REGULATOR_SUPPLY("vdd", "spi0.0"),
-};
-
-static struct regulator_init_data vgen_init = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = 1,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vgen_consumers),
- .consumer_supplies = vgen_consumers,
-};
-
-static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
- {
- .id = MC13783_REG_PWGT1SPI, /* Power Gate for ARM core. */
- .init_data = &pwgtx_init,
- }, {
- .id = MC13783_REG_PWGT2SPI, /* Power Gate for L2 Cache. */
- .init_data = &pwgtx_init,
- }, {
-
- .id = MC13783_REG_GPO1, /* Turn on 1.8V */
- .init_data = &gpo_init,
- }, {
- .id = MC13783_REG_GPO3, /* Turn on 3.3V */
- .init_data = &gpo_init,
- }, {
- .id = MC13783_REG_VMMC2, /* Power MMC/SD, WiFi/Bluetooth. */
- .init_data = &vmmc2_init,
- }, {
- .id = MC13783_REG_VMMC1, /* Power LCD, CMOS, FM, GPS, Accel. */
- .init_data = &vmmc1_init,
- }, {
- .id = MC13783_REG_VGEN, /* Power LCD */
- .init_data = &vgen_init,
- },
-};
-
-/* MC13783 */
-static struct mc13xxx_codec_platform_data mx31_3ds_codec = {
- .dac_ssi_port = MC13783_SSI1_PORT,
- .adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data mc13783_pdata = {
- .regulators = {
- .regulators = mx31_3ds_regulators,
- .num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
- },
- .codec = &mx31_3ds_codec,
- .flags = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC | MC13XXX_USE_CODEC,
-
-};
-
-static struct imx_ssi_platform_data mx31_3ds_ssi_pdata = {
- .flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-static struct spi_board_info mx31_3ds_spi_devs[] __initdata = {
- {
- .modalias = "mc13783",
- .max_speed_hz = 1000000,
- .bus_num = 1,
- .chip_select = 2, /* SS2 */
- .platform_data = &mc13783_pdata,
- /* irq number is run-time assigned */
- .mode = SPI_CS_HIGH,
- }, {
- .modalias = "l4f00242t03",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 2, /* SS2 */
- },
-};
-
-/*
- * NAND Flash
- */
-static const struct mxc_nand_platform_data
-mx31_3ds_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-#ifdef CONFIG_MACH_MX31_3DS_MXC_NAND_USE_BBT
- .flash_bbt = 1,
-#endif
-};
-
-/*
- * USB OTG
- */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-#define USBOTG_RST_B IOMUX_TO_GPIO(MX31_PIN_USB_PWR)
-#define USBH2_RST_B IOMUX_TO_GPIO(MX31_PIN_USB_BYP)
-
-static int mx31_3ds_usbotg_init(void)
-{
- int err;
-
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
-
- err = gpio_request(USBOTG_RST_B, "otgusb-reset");
- if (err) {
- pr_err("Failed to request the USB OTG reset gpio\n");
- return err;
- }
-
- err = gpio_direction_output(USBOTG_RST_B, 0);
- if (err) {
- pr_err("Failed to drive the USB OTG reset gpio\n");
- goto usbotg_free_reset;
- }
-
- mdelay(1);
- gpio_set_value(USBOTG_RST_B, 1);
- return 0;
-
-usbotg_free_reset:
- gpio_free(USBOTG_RST_B);
- return err;
-}
-
-static int mx31_3ds_otg_init(struct platform_device *pdev)
-{
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static int mx31_3ds_host2_init(struct platform_device *pdev)
-{
- int err;
-
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_PC_VS2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_PC_BVD1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_PC_BVD2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_PC_RST, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_IOIS16, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_PC_RW_B, USB_PAD_CFG);
-
- err = gpio_request(USBH2_RST_B, "usbh2-reset");
- if (err) {
- pr_err("Failed to request the USB Host 2 reset gpio\n");
- return err;
- }
-
- err = gpio_direction_output(USBH2_RST_B, 0);
- if (err) {
- pr_err("Failed to drive the USB Host 2 reset gpio\n");
- goto usbotg_free_reset;
- }
-
- mdelay(1);
- gpio_set_value(USBH2_RST_B, 1);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-
-usbotg_free_reset:
- gpio_free(USBH2_RST_B);
- return err;
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = mx31_3ds_otg_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = mx31_3ds_host2_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data usbotg_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx31_3ds_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", mx31_3ds_otg_mode);
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data mx31_3ds_i2c0_data __initconst = {
- .bitrate = 100000,
-};
-
-static void __init mx31_3ds_init(void)
-{
- imx31_soc_init();
-
- /* Configure SPI1 IOMUX */
- mxc_iomux_set_gpr(MUX_PGP_CSPI_BB, true);
-
- mxc_iomux_setup_multiple_pins(mx31_3ds_pins, ARRAY_SIZE(mx31_3ds_pins),
- "mx31_3ds");
-
- imx31_add_imx_uart0(&uart_pdata);
- imx31_add_mxc_nand(&mx31_3ds_nand_board_info);
-
- imx31_add_spi_imx1(NULL);
-
- imx31_add_imx_keypad(&mx31_3ds_keymap_data);
-
- imx31_add_imx2_wdt();
- imx31_add_imx_i2c0(&mx31_3ds_i2c0_data);
-
- imx31_add_spi_imx0(NULL);
- imx31_add_ipu_core();
- imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
- imx31_add_imx_ssi(0, &mx31_3ds_ssi_pdata);
-
- imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-}
-
-static void __init mx31_3ds_late(void)
-{
- gpiod_add_lookup_table(&mx31_3ds_lcd_gpiod_table);
- mx31_3ds_spi_devs[0].irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
- spi_register_board_info(mx31_3ds_spi_devs,
- ARRAY_SIZE(mx31_3ds_spi_devs));
-
- mx31_3ds_usbotg_init();
- if (otg_mode_host) {
- otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (otg_pdata.otg)
- imx31_add_mxc_ehci_otg(&otg_pdata);
- }
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbh2_pdata.otg)
- imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
- if (!otg_mode_host)
- imx31_add_fsl_usb2_udc(&usbotg_pdata);
-
- if (mxc_expio_init(MX31_CS5_BASE_ADDR, IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)))
- printk(KERN_WARNING "Init of the debug board failed, all "
- "devices on the debug board are unusable.\n");
-
- imx31_add_mxc_mmc(0, &sdhc1_pdata);
-}
-
-static void __init mx31_3ds_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
- /* Maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31_3ds_timer_init,
- .init_machine = mx31_3ds_init,
- .init_late = mx31_3ds_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c
deleted file mode 100644
index 4978338..0000000
--- a/arch/arm/mach-imx/mach-mx31ads.c
+++ /dev/null
@@ -1,579 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/serial_8250.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-#include <linux/mfd/wm8350/audio.h>
-#include <linux/mfd/wm8350/core.h>
-#include <linux/mfd/wm8350/pmic.h>
-#endif
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/* Base address of PBC controller */
-#define PBC_BASE_ADDRESS MX31_CS4_BASE_ADDR_VIRT
-
-/* PBC Board interrupt status register */
-#define PBC_INTSTATUS 0x000016
-
-/* PBC Board interrupt current status register */
-#define PBC_INTCURR_STATUS 0x000018
-
-/* PBC Interrupt mask register set address */
-#define PBC_INTMASK_SET 0x00001A
-
-/* PBC Interrupt mask register clear address */
-#define PBC_INTMASK_CLEAR 0x00001C
-
-/* External UART A */
-#define PBC_SC16C652_UARTA 0x010000
-
-/* External UART B */
-#define PBC_SC16C652_UARTB 0x010010
-
-#define PBC_INTSTATUS_REG (PBC_INTSTATUS + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_SET_REG (PBC_INTMASK_SET + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_CLEAR_REG (PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
-
-#define EXPIO_INT_XUART_INTA 10
-#define EXPIO_INT_XUART_INTB 11
-
-#define MXC_MAX_EXP_IO_LINES 16
-
-/* CS8900 */
-#define EXPIO_INT_ENET_INT 8
-#define CS4_CS8900_MMIO_START 0x20000
-
-static struct irq_domain *domain;
-
-/*
- * The serial port definition structure.
- */
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
- .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTA),
- .uartclk = 14745600,
- .regshift = 0,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
- }, {
- .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
- .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTB),
- .uartclk = 14745600,
- .regshift = 0,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
- },
- {},
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = 0,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static struct resource mx31ads_cs8900_resources[] __initdata = {
- DEFINE_RES_MEM(MX31_CS4_BASE_ADDR + CS4_CS8900_MMIO_START, SZ_64K),
- DEFINE_RES_IRQ(-1),
-};
-
-static const struct platform_device_info mx31ads_cs8900_devinfo __initconst = {
- .name = "cs89x0",
- .id = 0,
- .res = mx31ads_cs8900_resources,
- .num_res = ARRAY_SIZE(mx31ads_cs8900_resources),
-};
-
-static int __init mxc_init_extuart(void)
-{
- serial_platform_data[0].irq = irq_find_mapping(domain,
- EXPIO_INT_XUART_INTA);
- serial_platform_data[1].irq = irq_find_mapping(domain,
- EXPIO_INT_XUART_INTB);
- return platform_device_register(&serial_device);
-}
-
-static void __init mxc_init_ext_ethernet(void)
-{
- mx31ads_cs8900_resources[1].start =
- irq_find_mapping(domain, EXPIO_INT_ENET_INT);
- mx31ads_cs8900_resources[1].end =
- irq_find_mapping(domain, EXPIO_INT_ENET_INT);
- platform_device_register_full(
- (struct platform_device_info *)&mx31ads_cs8900_devinfo);
-}
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static unsigned int uart_pins[] = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1
-};
-
-static inline void mxc_init_imx_uart(void)
-{
- mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
- imx31_add_imx_uart0(&uart_pdata);
-}
-
-static void mx31ads_expio_irq_handler(struct irq_desc *desc)
-{
- u32 imr_val;
- u32 int_valid;
- u32 expio_irq;
-
- imr_val = imx_readw(PBC_INTMASK_SET_REG);
- int_valid = imx_readw(PBC_INTSTATUS_REG) & imr_val;
-
- expio_irq = 0;
- for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
- if ((int_valid & 1) == 0)
- continue;
-
- generic_handle_irq(irq_find_mapping(domain, expio_irq));
- }
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * @param d an expio virtual irq description
- */
-static void expio_mask_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* mask the interrupt */
- imx_writew(1 << expio, PBC_INTMASK_CLEAR_REG);
- imx_readw(PBC_INTMASK_CLEAR_REG);
-}
-
-/*
- * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
- * @param d an expio virtual irq description
- */
-static void expio_ack_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* clear the interrupt status */
- imx_writew(1 << expio, PBC_INTSTATUS_REG);
-}
-
-/*
- * Enable a expio pin's interrupt by clearing the bit in the imr.
- * @param d an expio virtual irq description
- */
-static void expio_unmask_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* unmask the interrupt */
- imx_writew(1 << expio, PBC_INTMASK_SET_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
- .name = "EXPIO(CPLD)",
- .irq_ack = expio_ack_irq,
- .irq_mask = expio_mask_irq,
- .irq_unmask = expio_unmask_irq,
-};
-
-static void __init mx31ads_init_expio(void)
-{
- int irq_base;
- int i, irq;
-
- printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");
-
- /*
- * Configure INT line as GPIO input
- */
- mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");
-
- /* disable the interrupt and clear the status */
- imx_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
- imx_writew(0xFFFF, PBC_INTSTATUS_REG);
-
- irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
- WARN_ON(irq_base < 0);
-
- domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
- &irq_domain_simple_ops, NULL);
- WARN_ON(!domain);
-
- for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
- irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
- irq_clear_status_flags(i, IRQ_NOREQUEST);
- }
- irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
- irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);
- irq_set_chained_handler(irq, mx31ads_expio_irq_handler);
-}
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-/* This section defines setup for the Wolfson Microelectronics
- * 1133-EV1 PMU/audio board. When other PMU boards are supported the
- * regulator definitions may be shared with them, but for now they can
- * only be used with this board so would generate warnings about
- * unused statics and some of the configuration is specific to this
- * module.
- */
-
-/* CPU */
-static struct regulator_consumer_supply sw1a_consumers[] = {
- {
- .supply = "cpu_vcc",
- }
-};
-
-static struct regulator_init_data sw1a_data = {
- .constraints = {
- .name = "SW1A",
- .min_uV = 1275000,
- .max_uV = 1600000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_MODE,
- .valid_modes_mask = REGULATOR_MODE_NORMAL |
- REGULATOR_MODE_FAST,
- .state_mem = {
- .uV = 1400000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(sw1a_consumers),
- .consumer_supplies = sw1a_consumers,
-};
-
-/* System IO - High */
-static struct regulator_init_data viohi_data = {
- .constraints = {
- .name = "VIOHO",
- .min_uV = 2800000,
- .max_uV = 2800000,
- .state_mem = {
- .uV = 2800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* System IO - Low */
-static struct regulator_init_data violo_data = {
- .constraints = {
- .name = "VIOLO",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .state_mem = {
- .uV = 1800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* DDR RAM */
-static struct regulator_init_data sw2a_data = {
- .constraints = {
- .name = "SW2A",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .state_mem = {
- .uV = 1800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .state_disk = {
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 0,
- },
- .always_on = 1,
- .boot_on = 1,
- .initial_state = PM_SUSPEND_MEM,
- },
-};
-
-static struct regulator_init_data ldo1_data = {
- .constraints = {
- .name = "VCAM/VMMC1/VMMC2",
- .min_uV = 2800000,
- .max_uV = 2800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .apply_uV = 1,
- },
-};
-
-static struct regulator_consumer_supply ldo2_consumers[] = {
- { .supply = "AVDD", .dev_name = "1-001a" },
- { .supply = "HPVDD", .dev_name = "1-001a" },
-};
-
-/* CODEC and SIM */
-static struct regulator_init_data ldo2_data = {
- .constraints = {
- .name = "VESIM/VSIM/AVDD",
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .apply_uV = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
- .consumer_supplies = ldo2_consumers,
-};
-
-/* General */
-static struct regulator_init_data vdig_data = {
- .constraints = {
- .name = "VDIG",
- .min_uV = 1500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .apply_uV = 1,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* Tranceivers */
-static struct regulator_init_data ldo4_data = {
- .constraints = {
- .name = "VRF1/CVDD_2.775",
- .min_uV = 2500000,
- .max_uV = 2500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .apply_uV = 1,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-static struct wm8350_led_platform_data wm8350_led_data = {
- .name = "wm8350:white",
- .default_trigger = "heartbeat",
- .max_uA = 27899,
-};
-
-static struct wm8350_audio_platform_data imx32ads_wm8350_setup = {
- .vmid_discharge_msecs = 1000,
- .drain_msecs = 30,
- .cap_discharge_msecs = 700,
- .vmid_charge_msecs = 700,
- .vmid_s_curve = WM8350_S_CURVE_SLOW,
- .dis_out4 = WM8350_DISCHARGE_SLOW,
- .dis_out3 = WM8350_DISCHARGE_SLOW,
- .dis_out2 = WM8350_DISCHARGE_SLOW,
- .dis_out1 = WM8350_DISCHARGE_SLOW,
- .vroi_out4 = WM8350_TIE_OFF_500R,
- .vroi_out3 = WM8350_TIE_OFF_500R,
- .vroi_out2 = WM8350_TIE_OFF_500R,
- .vroi_out1 = WM8350_TIE_OFF_500R,
- .vroi_enable = 0,
- .codec_current_on = WM8350_CODEC_ISEL_1_0,
- .codec_current_standby = WM8350_CODEC_ISEL_0_5,
- .codec_current_charge = WM8350_CODEC_ISEL_1_5,
-};
-
-static int mx31_wm8350_init(struct wm8350 *wm8350)
-{
- wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN,
- WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_ON);
-
- wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN,
- WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_ON);
-
- wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN,
- WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN,
- WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data);
-
- /* LEDs */
- wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1,
- WM8350_DC5_ERRACT_SHUTDOWN_CONV);
- wm8350_isink_set_flash(wm8350, WM8350_ISINK_A,
- WM8350_ISINK_FLASH_DISABLE,
- WM8350_ISINK_FLASH_TRIG_BIT,
- WM8350_ISINK_FLASH_DUR_32MS,
- WM8350_ISINK_FLASH_ON_INSTANT,
- WM8350_ISINK_FLASH_OFF_INSTANT,
- WM8350_ISINK_FLASH_MODE_EN);
- wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5,
- WM8350_ISINK_MODE_BOOST,
- WM8350_ISINK_ILIM_NORMAL,
- WM8350_DC5_RMP_20V,
- WM8350_DC5_FBSRC_ISINKA);
- wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A,
- &wm8350_led_data);
-
- wm8350->codec.platform_data = &imx32ads_wm8350_setup;
-
- regulator_has_full_constraints();
-
- return 0;
-}
-
-static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
- .init = mx31_wm8350_init,
-};
-#endif
-
-static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
- {
- I2C_BOARD_INFO("wm8350", 0x1a),
- .platform_data = &mx31_wm8350_pdata,
- /* irq number is run-time assigned */
- },
-#endif
-};
-
-static void __init mxc_init_i2c(void)
-{
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
- mx31ads_i2c1_devices[0].irq =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-#endif
- i2c_register_board_info(1, mx31ads_i2c1_devices,
- ARRAY_SIZE(mx31ads_i2c1_devices));
-
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));
-
- imx31_add_imx_i2c1(NULL);
-}
-
-static unsigned int ssi_pins[] = {
- MX31_PIN_SFS5__SFS5,
- MX31_PIN_SCK5__SCK5,
- MX31_PIN_SRXD5__SRXD5,
- MX31_PIN_STXD5__STXD5,
-};
-
-static void __init mxc_init_audio(void)
-{
- imx31_add_imx_ssi(0, NULL);
- mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
-}
-
-/*
- * Static mappings, starting from the CS4 start address up to the start address
- * of the CS8900.
- */
-static struct map_desc mx31ads_io_desc[] __initdata = {
- {
- .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
- .length = CS4_CS8900_MMIO_START,
- .type = MT_DEVICE
- },
-};
-
-static void __init mx31ads_map_io(void)
-{
- mx31_map_io();
- iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
-}
-
-static void __init mx31ads_init(void)
-{
- imx31_soc_init();
-
- mxc_init_imx_uart();
- mxc_init_audio();
-}
-
-static void __init mx31ads_late(void)
-{
- mx31ads_init_expio();
- mxc_init_extuart();
- mxc_init_i2c();
- mxc_init_ext_ethernet();
-}
-
-static void __init mx31ads_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31ADS, "Freescale MX31ADS")
- /* Maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx31ads_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31ads_timer_init,
- .init_machine = mx31ads_init,
- .init_late = mx31ads_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c
deleted file mode 100644
index 4b955cc..0000000
--- a/arch/arm/mach-imx/mach-mx31lilly.c
+++ /dev/null
@@ -1,312 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LILLY-1131 module support
- *
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * based on code for other MX31 boards,
- *
- * Copyright 2005-2007 Freescale Semiconductor
- * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/moduleparam.h>
-#include <linux/smsc911x.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lilly.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-/*
- * This file contains module-specific initialization routines for LILLY-1131.
- * Initialization of peripherals found on the baseboard is implemented in the
- * appropriate baseboard support code.
- */
-
-static unsigned int mx31lilly_pins[] __initdata = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
- MX31_PIN_CTS2__CTS2,
- MX31_PIN_RTS2__RTS2,
- MX31_PIN_TXD2__TXD2,
- MX31_PIN_RXD2__RXD2,
- MX31_PIN_CSPI3_MOSI__RXD3,
- MX31_PIN_CSPI3_MISO__TXD3,
- MX31_PIN_CSPI3_SCLK__RTS3,
- MX31_PIN_CSPI3_SPI_RDY__CTS3,
-};
-
-/* UART */
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-/* SMSC ethernet support */
-
-static struct resource smsc91x_resources[] = {
- {
- .start = MX31_CS4_BASE_ADDR,
- .end = MX31_CS4_BASE_ADDR + 0xffff,
- .flags = IORESOURCE_MEM,
- },
- {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
- }
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT |
- SMSC911X_SAVE_MAC_ADDRESS |
- SMSC911X_FORCE_INTERNAL_PHY,
-};
-
-static struct platform_device smsc91x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smsc91x_resources),
- .resource = smsc91x_resources,
- .dev = {
- .platform_data = &smsc911x_config,
- }
-};
-
-/* NOR flash */
-static struct physmap_flash_data nor_flash_data = {
- .width = 2,
-};
-
-static struct resource nor_flash_resource = {
- .start = 0xa0000000,
- .end = 0xa1ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device physmap_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &nor_flash_data,
- },
- .resource = &nor_flash_resource,
- .num_resources = 1,
-};
-
-/* USB */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbh1_init(struct platform_device *pdev)
-{
- int pins[] = {
- MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
- MX31_PIN_CSPI1_MISO__USBH1_RXDP,
- MX31_PIN_CSPI1_SS0__USBH1_TXDM,
- MX31_PIN_CSPI1_SS1__USBH1_TXDP,
- MX31_PIN_CSPI1_SS2__USBH1_RCV,
- MX31_PIN_CSPI1_SCLK__USBH1_OEB,
- MX31_PIN_CSPI1_SPI_RDY__USBH1_FS,
- };
-
- mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H1");
-
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
-
- mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-static int usbh2_init(struct platform_device *pdev)
-{
- int pins[] = {
- MX31_PIN_USBH2_DATA0__USBH2_DATA0,
- MX31_PIN_USBH2_DATA1__USBH2_DATA1,
- MX31_PIN_USBH2_CLK__USBH2_CLK,
- MX31_PIN_USBH2_DIR__USBH2_DIR,
- MX31_PIN_USBH2_NXT__USBH2_NXT,
- MX31_PIN_USBH2_STP__USBH2_STP,
- };
-
- mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");
-
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
- mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
- /* chip select */
- mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
- "USBH2_CS");
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
- gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
- .init = usbh1_init,
- .portsc = MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = usbh2_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static void __init lilly1131_usb_init(void)
-{
- imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbh2_pdata.otg)
- imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
- .flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static struct spi_board_info mc13783_dev __initdata = {
- .modalias = "mc13783",
- .max_speed_hz = 1000000,
- .bus_num = 1,
- .chip_select = 0,
- .platform_data = &mc13783_pdata,
- /* irq number is run-time assigned */
-};
-
-static struct platform_device *devices[] __initdata = {
- &smsc91x_device,
- &physmap_flash_device,
-};
-
-static int mx31lilly_baseboard;
-core_param(mx31lilly_baseboard, mx31lilly_baseboard, int, 0444);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static void __init mx31lilly_board_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(mx31lilly_pins,
- ARRAY_SIZE(mx31lilly_pins), "mx31lily");
-
- imx31_add_imx_uart0(&uart_pdata);
- imx31_add_imx_uart1(&uart_pdata);
- imx31_add_imx_uart2(&uart_pdata);
-
- mxc_iomux_alloc_pin(MX31_PIN_CS4__CS4, "Ethernet CS");
-
- /* SPI */
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SCLK__SCLK, "SPI1_CLK");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MOSI__MOSI, "SPI1_TX");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MISO__MISO, "SPI1_RX");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, "SPI1_RDY");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS0__SS0, "SPI1_SS0");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS1__SS1, "SPI1_SS1");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS2__SS2, "SPI1_SS2");
-
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SCLK__SCLK, "SPI2_CLK");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MOSI__MOSI, "SPI2_TX");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MISO__MISO, "SPI2_RX");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SPI_RDY__SPI_RDY, "SPI2_RDY");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS0__SS0, "SPI2_SS0");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS1__SS1, "SPI2_SS1");
- mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS2__SS2, "SPI2_SS2");
-
- imx31_add_spi_imx0(NULL);
- imx31_add_spi_imx1(NULL);
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-}
-
-static void __init mx31lilly_late_init(void)
-{
- if (mx31lilly_baseboard == MX31LILLY_DB)
- mx31lilly_db_init();
-
- mc13783_dev.irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
- spi_register_board_info(&mc13783_dev, 1);
-
- smsc91x_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
- smsc91x_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- /* USB */
- lilly1131_usb_init();
-}
-
-static void __init mx31lilly_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(LILLY1131, "INCO startec LILLY-1131")
- .atag_offset = 0x100,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31lilly_timer_init,
- .init_machine = mx31lilly_board_init,
- .init_late = mx31lilly_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31lite.c b/arch/arm/mach-imx/mach-mx31lite.c
deleted file mode 100644
index aaccf52..0000000
--- a/arch/arm/mach-imx/mach-mx31lite.c
+++ /dev/null
@@ -1,290 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/memory.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/moduleparam.h>
-#include <linux/smsc911x.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/mtd/physmap.h>
-#include <linux/delay.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/page.h>
-#include <asm/setup.h>
-
-#include "board-mx31lite.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-/*
- * This file contains the module-specific initialization routines.
- */
-
-static unsigned int mx31lite_pins[] = {
- /* UART1 */
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
- /* SPI 0 */
- MX31_PIN_CSPI1_SCLK__SCLK,
- MX31_PIN_CSPI1_MOSI__MOSI,
- MX31_PIN_CSPI1_MISO__MISO,
- MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI1_SS0__SS0,
- MX31_PIN_CSPI1_SS1__SS1,
- MX31_PIN_CSPI1_SS2__SS2,
- /* LAN9117 IRQ pin */
- IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO),
- /* SPI 1 */
- MX31_PIN_CSPI2_SCLK__SCLK,
- MX31_PIN_CSPI2_MOSI__MOSI,
- MX31_PIN_CSPI2_MISO__MISO,
- MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI2_SS0__SS0,
- MX31_PIN_CSPI2_SS1__SS1,
- MX31_PIN_CSPI2_SS2__SS2,
-};
-
-/* UART */
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-mx31lite_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_16BIT,
-};
-
-static struct resource smsc911x_resources[] = {
- {
- .start = MX31_CS4_BASE_ADDR,
- .end = MX31_CS4_BASE_ADDR + 0x100,
- .flags = IORESOURCE_MEM,
- }, {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smsc911x_resources),
- .resource = smsc911x_resources,
- .dev = {
- .platform_data = &smsc911x_config,
- },
-};
-
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
- .flags = MC13XXX_USE_RTC,
-};
-
-static struct spi_board_info mc13783_spi_dev __initdata = {
- .modalias = "mc13783",
- .max_speed_hz = 1000000,
- .bus_num = 1,
- .chip_select = 0,
- .platform_data = &mc13783_pdata,
- /* irq number is run-time assigned */
-};
-
-/*
- * USB
- */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbh2_init(struct platform_device *pdev)
-{
- int pins[] = {
- MX31_PIN_USBH2_DATA0__USBH2_DATA0,
- MX31_PIN_USBH2_DATA1__USBH2_DATA1,
- MX31_PIN_USBH2_CLK__USBH2_CLK,
- MX31_PIN_USBH2_DIR__USBH2_DIR,
- MX31_PIN_USBH2_NXT__USBH2_NXT,
- MX31_PIN_USBH2_STP__USBH2_STP,
- };
-
- mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");
-
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
- mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
- /* chip select */
- mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
- "USBH2_CS");
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
- gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = usbh2_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/*
- * NOR flash
- */
-
-static struct physmap_flash_data nor_flash_data = {
- .width = 2,
-};
-
-static struct resource nor_flash_resource = {
- .start = 0xa0000000,
- .end = 0xa1ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device physmap_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &nor_flash_data,
- },
- .resource = &nor_flash_resource,
- .num_resources = 1,
-};
-
-/*
- * This structure defines the MX31 memory map.
- */
-static struct map_desc mx31lite_io_desc[] __initdata = {
- {
- .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
- .length = MX31_CS4_SIZE,
- .type = MT_DEVICE
- }
-};
-
-/*
- * Set up static virtual mappings.
- */
-static void __init mx31lite_map_io(void)
-{
- mx31_map_io();
- iotable_init(mx31lite_io_desc, ARRAY_SIZE(mx31lite_io_desc));
-}
-
-static int mx31lite_baseboard;
-core_param(mx31lite_baseboard, mx31lite_baseboard, int, 0444);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static void __init mx31lite_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(mx31lite_pins, ARRAY_SIZE(mx31lite_pins),
- "mx31lite");
-
- imx31_add_imx_uart0(&uart_pdata);
- imx31_add_spi_imx0(NULL);
-
- /* NOR and NAND flash */
- platform_device_register(&physmap_flash_device);
- imx31_add_mxc_nand(&mx31lite_nand_board_info);
-
- imx31_add_spi_imx1(NULL);
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-}
-
-static void __init mx31lite_late(void)
-{
- int ret;
-
- if (mx31lite_baseboard == MX31LITE_DB)
- mx31lite_db_init();
-
- mc13783_spi_dev.irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
- spi_register_board_info(&mc13783_spi_dev, 1);
-
- /* USB */
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbh2_pdata.otg)
- imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
- /* SMSC9117 IRQ pin */
- ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_SFS6), "sms9117-irq");
- if (ret)
- pr_warn("could not get LAN irq gpio\n");
- else {
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_SFS6));
- smsc911x_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
- smsc911x_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
- platform_device_register(&smsc911x_device);
- }
-}
-
-static void __init mx31lite_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
- /* Maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx31lite_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31lite_timer_init,
- .init_machine = mx31lite_init,
- .init_late = mx31lite_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
deleted file mode 100644
index 7f780ad..0000000
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ /dev/null
@@ -1,581 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2008 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/dma-map-ops.h>
-#include <linux/gfp.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/moduleparam.h>
-#include <linux/leds.h>
-#include <linux/memory.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/machine.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/types.h>
-#include <linux/memblock.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/err.h>
-#include <linux/input.h>
-
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/memblock.h>
-#include <linux/platform_data/asoc-imx-ssi.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int moboard_pins[] = {
- /* UART0 */
- MX31_PIN_TXD1__TXD1, MX31_PIN_RXD1__RXD1,
- MX31_PIN_CTS1__GPIO2_7,
- /* UART4 */
- MX31_PIN_PC_RST__CTS5, MX31_PIN_PC_VS2__RTS5,
- MX31_PIN_PC_BVD2__TXD5, MX31_PIN_PC_BVD1__RXD5,
- /* I2C0 */
- MX31_PIN_I2C_DAT__I2C1_SDA, MX31_PIN_I2C_CLK__I2C1_SCL,
- /* I2C1 */
- MX31_PIN_DCD_DTE1__I2C2_SDA, MX31_PIN_RI_DTE1__I2C2_SCL,
- /* SDHC1 */
- MX31_PIN_SD1_DATA3__SD1_DATA3, MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA1__SD1_DATA1, MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_CLK__SD1_CLK, MX31_PIN_SD1_CMD__SD1_CMD,
- MX31_PIN_ATA_CS0__GPIO3_26, MX31_PIN_ATA_CS1__GPIO3_27,
- /* USB reset */
- MX31_PIN_GPIO1_0__GPIO1_0,
- /* USB OTG */
- MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
- MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
- MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
- MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
- MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
- MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
- MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
- MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
- MX31_PIN_USBOTG_CLK__USBOTG_CLK, MX31_PIN_USBOTG_DIR__USBOTG_DIR,
- MX31_PIN_USBOTG_NXT__USBOTG_NXT, MX31_PIN_USBOTG_STP__USBOTG_STP,
- MX31_PIN_USB_OC__GPIO1_30,
- /* USB H2 */
- MX31_PIN_USBH2_DATA0__USBH2_DATA0,
- MX31_PIN_USBH2_DATA1__USBH2_DATA1,
- MX31_PIN_STXD3__USBH2_DATA2, MX31_PIN_SRXD3__USBH2_DATA3,
- MX31_PIN_SCK3__USBH2_DATA4, MX31_PIN_SFS3__USBH2_DATA5,
- MX31_PIN_STXD6__USBH2_DATA6, MX31_PIN_SRXD6__USBH2_DATA7,
- MX31_PIN_USBH2_CLK__USBH2_CLK, MX31_PIN_USBH2_DIR__USBH2_DIR,
- MX31_PIN_USBH2_NXT__USBH2_NXT, MX31_PIN_USBH2_STP__USBH2_STP,
- MX31_PIN_SCK6__GPIO1_25,
- /* LEDs */
- MX31_PIN_SVEN0__GPIO2_0, MX31_PIN_STX0__GPIO2_1,
- MX31_PIN_SRX0__GPIO2_2, MX31_PIN_SIMPD0__GPIO2_3,
- /* SPI1 */
- MX31_PIN_CSPI2_MOSI__MOSI, MX31_PIN_CSPI2_MISO__MISO,
- MX31_PIN_CSPI2_SCLK__SCLK, MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI2_SS0__SS0, MX31_PIN_CSPI2_SS2__SS2,
- /* Atlas IRQ */
- MX31_PIN_GPIO1_3__GPIO1_3,
- /* SPI2 */
- MX31_PIN_CSPI3_MOSI__MOSI, MX31_PIN_CSPI3_MISO__MISO,
- MX31_PIN_CSPI3_SCLK__SCLK, MX31_PIN_CSPI3_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI2_SS1__CSPI3_SS1,
- /* SSI */
- MX31_PIN_STXD4__STXD4, MX31_PIN_SRXD4__SRXD4,
- MX31_PIN_SCK4__SCK4, MX31_PIN_SFS4__SFS4,
-};
-
-static struct physmap_flash_data mx31moboard_flash_data = {
- .width = 2,
-};
-
-static struct resource mx31moboard_flash_resource = {
- .start = 0xa0000000,
- .end = 0xa1ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device mx31moboard_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &mx31moboard_flash_data,
- },
- .resource = &mx31moboard_flash_resource,
- .num_resources = 1,
-};
-
-static void __init moboard_uart0_init(void)
-{
- if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_CTS1), "uart0-cts-hack")) {
- gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_CTS1), 0);
- gpio_free(IOMUX_TO_GPIO(MX31_PIN_CTS1));
- }
-}
-
-static const struct imxuart_platform_data uart0_pdata __initconst = {
-};
-
-static const struct imxuart_platform_data uart4_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data moboard_i2c0_data __initconst = {
- .bitrate = 400000,
-};
-
-static const struct imxi2c_platform_data moboard_i2c1_data __initconst = {
- .bitrate = 100000,
-};
-
-static struct regulator_consumer_supply sdhc_consumers[] = {
- {
- .dev_name = "imx31-mmc.0",
- .supply = "sdhc0_vcc",
- },
- {
- .dev_name = "imx31-mmc.1",
- .supply = "sdhc1_vcc",
- },
-};
-
-static struct regulator_init_data sdhc_vreg_data = {
- .constraints = {
- .min_uV = 2700000,
- .max_uV = 3000000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- .valid_modes_mask = REGULATOR_MODE_NORMAL |
- REGULATOR_MODE_FAST,
- .always_on = 0,
- .boot_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(sdhc_consumers),
- .consumer_supplies = sdhc_consumers,
-};
-
-static struct regulator_consumer_supply cam_consumers[] = {
- {
- .dev_name = "mx3_camera.0",
- .supply = "cam_vcc",
- },
-};
-
-static struct regulator_init_data cam_vreg_data = {
- .constraints = {
- .min_uV = 2700000,
- .max_uV = 3000000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- .valid_modes_mask = REGULATOR_MODE_NORMAL |
- REGULATOR_MODE_FAST,
- .always_on = 0,
- .boot_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(cam_consumers),
- .consumer_supplies = cam_consumers,
-};
-
-static struct mc13xxx_regulator_init_data moboard_regulators[] = {
- {
- .id = MC13783_REG_VMMC1,
- .init_data = &sdhc_vreg_data,
- },
- {
- .id = MC13783_REG_VCAM,
- .init_data = &cam_vreg_data,
- },
-};
-
-static struct mc13xxx_led_platform_data moboard_led[] = {
- {
- .id = MC13783_LED_R1,
- .name = "coreboard-led-4:red",
- },
- {
- .id = MC13783_LED_G1,
- .name = "coreboard-led-4:green",
- },
- {
- .id = MC13783_LED_B1,
- .name = "coreboard-led-4:blue",
- },
- {
- .id = MC13783_LED_R2,
- .name = "coreboard-led-5:red",
- },
- {
- .id = MC13783_LED_G2,
- .name = "coreboard-led-5:green",
- },
- {
- .id = MC13783_LED_B2,
- .name = "coreboard-led-5:blue",
- },
-};
-
-static struct mc13xxx_leds_platform_data moboard_leds = {
- .num_leds = ARRAY_SIZE(moboard_led),
- .led = moboard_led,
- .led_control[0] = MC13783_LED_C0_ENABLE | MC13783_LED_C0_ABMODE(0),
- .led_control[1] = MC13783_LED_C1_SLEWLIM,
- .led_control[2] = MC13783_LED_C2_SLEWLIM,
- .led_control[3] = MC13783_LED_C3_PERIOD(0) |
- MC13783_LED_C3_CURRENT_R1(2) |
- MC13783_LED_C3_CURRENT_G1(2) |
- MC13783_LED_C3_CURRENT_B1(2),
- .led_control[4] = MC13783_LED_C4_PERIOD(0) |
- MC13783_LED_C4_CURRENT_R2(3) |
- MC13783_LED_C4_CURRENT_G2(3) |
- MC13783_LED_C4_CURRENT_B2(3),
-};
-
-static struct mc13xxx_buttons_platform_data moboard_buttons = {
- .b1on_flags = MC13783_BUTTON_DBNC_750MS | MC13783_BUTTON_ENABLE |
- MC13783_BUTTON_POL_INVERT,
- .b1on_key = KEY_POWER,
-};
-
-static struct mc13xxx_codec_platform_data moboard_codec = {
- .dac_ssi_port = MC13783_SSI1_PORT,
- .adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data moboard_pmic = {
- .regulators = {
- .regulators = moboard_regulators,
- .num_regulators = ARRAY_SIZE(moboard_regulators),
- },
- .leds = &moboard_leds,
- .buttons = &moboard_buttons,
- .codec = &moboard_codec,
- .flags = MC13XXX_USE_RTC | MC13XXX_USE_ADC | MC13XXX_USE_CODEC,
-};
-
-static struct imx_ssi_platform_data moboard_ssi_pdata = {
- .flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-static struct spi_board_info moboard_spi_board_info[] __initdata = {
- {
- .modalias = "mc13783",
- /* irq number is run-time assigned */
- .max_speed_hz = 300000,
- .bus_num = 1,
- .chip_select = 0,
- .platform_data = &moboard_pmic,
- .mode = SPI_CS_HIGH,
- },
-};
-
-#define SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_ATA_CS0)
-#define SDHC1_WP IOMUX_TO_GPIO(MX31_PIN_ATA_CS1)
-
-static int moboard_sdhc1_get_ro(struct device *dev)
-{
- return !gpio_get_value(SDHC1_WP);
-}
-
-static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request(SDHC1_CD, "sdhc-detect");
- if (ret)
- return ret;
-
- gpio_direction_input(SDHC1_CD);
-
- ret = gpio_request(SDHC1_WP, "sdhc-wp");
- if (ret)
- goto err_gpio_free;
- gpio_direction_input(SDHC1_WP);
-
- ret = request_irq(gpio_to_irq(SDHC1_CD), detect_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "sdhc1-card-detect", data);
- if (ret)
- goto err_gpio_free_2;
-
- return 0;
-
-err_gpio_free_2:
- gpio_free(SDHC1_WP);
-err_gpio_free:
- gpio_free(SDHC1_CD);
-
- return ret;
-}
-
-static void moboard_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(SDHC1_CD), data);
- gpio_free(SDHC1_WP);
- gpio_free(SDHC1_CD);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
- .get_ro = moboard_sdhc1_get_ro,
- .init = moboard_sdhc1_init,
- .exit = moboard_sdhc1_exit,
-};
-
-/*
- * this pin is dedicated for all mx31moboard systems, so we do it here
- */
-#define USB_RESET_B IOMUX_TO_GPIO(MX31_PIN_GPIO1_0)
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS)
-
-#define OTG_EN_B IOMUX_TO_GPIO(MX31_PIN_USB_OC)
-#define USBH2_EN_B IOMUX_TO_GPIO(MX31_PIN_SCK6)
-
-static void usb_xcvr_reset(void)
-{
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG | PAD_CTL_100K_PU);
-
- mxc_iomux_set_gpr(MUX_PGP_UH2, true);
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG | PAD_CTL_100K_PD);
- mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG | PAD_CTL_100K_PD);
-
- gpio_request(OTG_EN_B, "usb-udc-en");
- gpio_direction_output(OTG_EN_B, 0);
- gpio_request(USBH2_EN_B, "usbh2-en");
- gpio_direction_output(USBH2_EN_B, 0);
-
- gpio_request(USB_RESET_B, "usb-reset");
- gpio_direction_output(USB_RESET_B, 0);
- mdelay(1);
- gpio_set_value(USB_RESET_B, 1);
- mdelay(1);
-}
-
-static int moboard_usbh2_init_hw(struct platform_device *pdev)
-{
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = moboard_usbh2_init_hw,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static int __init moboard_usbh2_init(void)
-{
- struct platform_device *pdev;
-
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (!usbh2_pdata.otg)
- return -ENODEV;
-
- pdev = imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
- return PTR_ERR_OR_ZERO(pdev);
-}
-
-static const struct gpio_led mx31moboard_leds[] __initconst = {
- {
- .name = "coreboard-led-0:red:running",
- .default_trigger = "heartbeat",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_SVEN0),
- }, {
- .name = "coreboard-led-1:red",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_STX0),
- }, {
- .name = "coreboard-led-2:red",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_SRX0),
- }, {
- .name = "coreboard-led-3:red",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_SIMPD0),
- },
-};
-
-static const struct gpio_led_platform_data mx31moboard_led_pdata __initconst = {
- .num_leds = ARRAY_SIZE(mx31moboard_leds),
- .leds = mx31moboard_leds,
-};
-
-static struct platform_device *devices[] __initdata = {
- &mx31moboard_flash,
-};
-
-static struct mx3_camera_pdata camera_pdata __initdata = {
- .flags = MX3_CAMERA_DATAWIDTH_8 | MX3_CAMERA_DATAWIDTH_10,
- .mclk_10khz = 4800,
-};
-
-static phys_addr_t mx3_camera_base __initdata;
-#define MX3_CAMERA_BUF_SIZE SZ_4M
-
-static int __init mx31moboard_init_cam(void)
-{
- int ret;
- struct platform_device *pdev;
-
- imx31_add_ipu_core();
-
- pdev = imx31_alloc_mx3_camera(&camera_pdata);
- if (IS_ERR(pdev))
- return PTR_ERR(pdev);
-
- ret = dma_declare_coherent_memory(&pdev->dev,
- mx3_camera_base, mx3_camera_base,
- MX3_CAMERA_BUF_SIZE);
- if (ret)
- goto err;
-
- ret = platform_device_add(pdev);
- if (ret)
-err:
- platform_device_put(pdev);
-
- return ret;
-
-}
-
-static void mx31moboard_poweroff(void)
-{
- struct clk *clk = clk_get_sys("imx2-wdt.0", NULL);
-
- if (!IS_ERR(clk))
- clk_prepare_enable(clk);
-
- mxc_iomux_mode(MX31_PIN_WATCHDOG_RST__WATCHDOG_RST);
-
- imx_writew(1 << 6 | 1 << 2, MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
-}
-
-static int mx31moboard_baseboard;
-core_param(mx31moboard_baseboard, mx31moboard_baseboard, int, 0444);
-
-/*
- * Board specific initialization.
- */
-static void __init mx31moboard_init(void)
-{
- imx31_soc_init();
-
- mxc_iomux_setup_multiple_pins(moboard_pins, ARRAY_SIZE(moboard_pins),
- "moboard");
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- imx31_add_imx2_wdt();
-
- imx31_add_imx_uart0(&uart0_pdata);
- imx31_add_imx_uart4(&uart4_pdata);
-
- imx31_add_imx_i2c0(&moboard_i2c0_data);
- imx31_add_imx_i2c1(&moboard_i2c1_data);
-
- imx31_add_spi_imx1(NULL);
- imx31_add_spi_imx2(NULL);
-
- mx31moboard_init_cam();
-
- imx31_add_imx_ssi(0, &moboard_ssi_pdata);
-
- pm_power_off = mx31moboard_poweroff;
-}
-
-static void __init mx31moboard_late(void)
-{
- gpio_led_register_device(-1, &mx31moboard_led_pdata);
-
- moboard_uart0_init();
-
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3), "pmic-irq");
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
- moboard_spi_board_info[0].irq =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
- spi_register_board_info(moboard_spi_board_info,
- ARRAY_SIZE(moboard_spi_board_info));
-
- imx31_add_mxc_mmc(0, &sdhc1_pdata);
-
- usb_xcvr_reset();
- moboard_usbh2_init();
-
- imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-
- switch (mx31moboard_baseboard) {
- case MX31NOBOARD:
- break;
- case MX31DEVBOARD:
- mx31moboard_devboard_init();
- break;
- case MX31MARXBOT:
- mx31moboard_marxbot_init();
- break;
- case MX31SMARTBOT:
- case MX31EYEBOT:
- mx31moboard_smartbot_init(mx31moboard_baseboard);
- break;
- default:
- printk(KERN_ERR "Illegal mx31moboard_baseboard type %d\n",
- mx31moboard_baseboard);
- }
-}
-
-static void __init mx31moboard_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-static void __init mx31moboard_reserve(void)
-{
- /* reserve 4 MiB for mx3-camera */
- mx3_camera_base = arm_memblock_steal(MX3_CAMERA_BUF_SIZE,
- MX3_CAMERA_BUF_SIZE);
-}
-
-MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
- /* Maintainer: Philippe Retornaz, EPFL Mobots group */
- .atag_offset = 0x100,
- .reserve = mx31moboard_reserve,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31moboard_timer_init,
- .init_machine = mx31moboard_init,
- .init_late = mx31moboard_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
deleted file mode 100644
index 802e0ab..0000000
--- a/arch/arm/mach-imx/mach-mx35_3ds.c
+++ /dev/null
@@ -1,516 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Marc Kleine-Budde, Pengutronix
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- *
- * Copyright (C) 2011 Meprolight, Ltd.
- * Alex Gershgorin <alexg@meprolight.com>
- *
- * Modified from i.MX31 3-Stack Development System
- */
-
-/*
- * This machine is known as:
- * - i.MX35 3-Stack Development System
- * - i.MX35 Platform Development Kit (i.MX35 PDK)
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/usb/otg.h>
-
-#include <linux/mtd/physmap.h>
-#include <linux/mfd/mc13892.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include <video/platform_lcd.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-#define GPIO_MC9S08DZ60_GPS_ENABLE 0
-#define GPIO_MC9S08DZ60_HDD_ENABLE 4
-#define GPIO_MC9S08DZ60_WIFI_ENABLE 5
-#define GPIO_MC9S08DZ60_LCD_ENABLE 6
-#define GPIO_MC9S08DZ60_SPEAKER_ENABLE 8
-
-static const struct fb_videomode fb_modedb[] = {
- {
- /* 800x480 @ 55 Hz */
- .name = "Ceramate-CLAA070VC01",
- .refresh = 55,
- .xres = 800,
- .yres = 480,
- .pixclock = 40000,
- .left_margin = 40,
- .right_margin = 40,
- .upper_margin = 5,
- .lower_margin = 5,
- .hsync_len = 20,
- .vsync_len = 10,
- .sync = FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "Ceramate-CLAA070VC01",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static struct i2c_board_info __initdata i2c_devices_3ds[] = {
- {
- I2C_BOARD_INFO("mc9s08dz60", 0x69),
- },
-};
-
-static int lcd_power_gpio = -ENXIO;
-
-static int mc9s08dz60_gpiochip_match(struct gpio_chip *chip, void *data)
-{
- return !strcmp(chip->label, data);
-}
-
-static void mx35_3ds_lcd_set_power(
- struct plat_lcd_data *pd, unsigned int power)
-{
- struct gpio_chip *chip;
-
- if (!gpio_is_valid(lcd_power_gpio)) {
- chip = gpiochip_find(
- "mc9s08dz60", mc9s08dz60_gpiochip_match);
- if (chip) {
- lcd_power_gpio =
- chip->base + GPIO_MC9S08DZ60_LCD_ENABLE;
- if (gpio_request(lcd_power_gpio, "lcd_power") < 0) {
- pr_err("error: gpio already requested!\n");
- lcd_power_gpio = -ENXIO;
- }
- } else {
- pr_err("error: didn't find mc9s08dz60 gpio chip\n");
- }
- }
-
- if (gpio_is_valid(lcd_power_gpio))
- gpio_set_value_cansleep(lcd_power_gpio, power);
-}
-
-static struct plat_lcd_data mx35_3ds_lcd_data = {
- .set_power = mx35_3ds_lcd_set_power,
-};
-
-static struct platform_device mx35_3ds_lcd = {
- .name = "platform-lcd",
- .dev.platform_data = &mx35_3ds_lcd_data,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct physmap_flash_data mx35pdk_flash_data = {
- .width = 2,
-};
-
-static struct resource mx35pdk_flash_resource = {
- .start = MX35_CS0_BASE_ADDR,
- .end = MX35_CS0_BASE_ADDR + SZ_64M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device mx35pdk_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &mx35pdk_flash_data,
- },
- .resource = &mx35pdk_flash_resource,
- .num_resources = 1,
-};
-
-static const struct mxc_nand_platform_data mx35pdk_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
- .flash_bbt = 1,
-};
-
-static struct platform_device *devices[] __initdata = {
- &mx35pdk_flash,
-};
-
-static const iomux_v3_cfg_t mx35pdk_pads[] __initconst = {
- /* UART1 */
- MX35_PAD_CTS1__UART1_CTS,
- MX35_PAD_RTS1__UART1_RTS,
- MX35_PAD_TXD1__UART1_TXD_MUX,
- MX35_PAD_RXD1__UART1_RXD_MUX,
- /* FEC */
- MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
- MX35_PAD_FEC_RX_DV__FEC_RX_DV,
- MX35_PAD_FEC_COL__FEC_COL,
- MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
- MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
- MX35_PAD_FEC_TX_EN__FEC_TX_EN,
- MX35_PAD_FEC_MDC__FEC_MDC,
- MX35_PAD_FEC_MDIO__FEC_MDIO,
- MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
- MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
- MX35_PAD_FEC_CRS__FEC_CRS,
- MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
- MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
- MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
- MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
- MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
- MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
- /* USBOTG */
- MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
- MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
- /* USBH1 */
- MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR,
- MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC,
- /* SDCARD */
- MX35_PAD_SD1_CMD__ESDHC1_CMD,
- MX35_PAD_SD1_CLK__ESDHC1_CLK,
- MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
- MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
- MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
- MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
- /* I2C1 */
- MX35_PAD_I2C1_CLK__I2C1_SCL,
- MX35_PAD_I2C1_DAT__I2C1_SDA,
- /* Display */
- MX35_PAD_LD0__IPU_DISPB_DAT_0,
- MX35_PAD_LD1__IPU_DISPB_DAT_1,
- MX35_PAD_LD2__IPU_DISPB_DAT_2,
- MX35_PAD_LD3__IPU_DISPB_DAT_3,
- MX35_PAD_LD4__IPU_DISPB_DAT_4,
- MX35_PAD_LD5__IPU_DISPB_DAT_5,
- MX35_PAD_LD6__IPU_DISPB_DAT_6,
- MX35_PAD_LD7__IPU_DISPB_DAT_7,
- MX35_PAD_LD8__IPU_DISPB_DAT_8,
- MX35_PAD_LD9__IPU_DISPB_DAT_9,
- MX35_PAD_LD10__IPU_DISPB_DAT_10,
- MX35_PAD_LD11__IPU_DISPB_DAT_11,
- MX35_PAD_LD12__IPU_DISPB_DAT_12,
- MX35_PAD_LD13__IPU_DISPB_DAT_13,
- MX35_PAD_LD14__IPU_DISPB_DAT_14,
- MX35_PAD_LD15__IPU_DISPB_DAT_15,
- MX35_PAD_LD16__IPU_DISPB_DAT_16,
- MX35_PAD_LD17__IPU_DISPB_DAT_17,
- MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
- MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
- MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
- MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
- MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
- MX35_PAD_D3_REV__IPU_DISPB_D3_REV,
- MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS,
- /*PMIC IRQ*/
- MX35_PAD_GPIO2_0__GPIO2_0,
-};
-
-static struct regulator_consumer_supply sw1_consumers[] = {
- {
- .supply = "cpu_vcc",
- }
-};
-
-static struct regulator_consumer_supply vcam_consumers[] = {
- /* sgtl5000 */
- REGULATOR_SUPPLY("VDDA", "0-000a"),
-};
-
-static struct regulator_init_data sw1_init = {
- .constraints = {
- .name = "SW1",
- .min_uV = 600000,
- .max_uV = 1375000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- .valid_modes_mask = 0,
- .always_on = 1,
- .boot_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(sw1_consumers),
- .consumer_supplies = sw1_consumers,
-};
-
-static struct regulator_init_data sw2_init = {
- .constraints = {
- .name = "SW2",
- .always_on = 1,
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data sw3_init = {
- .constraints = {
- .name = "SW3",
- .always_on = 1,
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data sw4_init = {
- .constraints = {
- .name = "SW4",
- .always_on = 1,
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data viohi_init = {
- .constraints = {
- .name = "VIOHI",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vusb_init = {
- .constraints = {
- .name = "VUSB",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vdig_init = {
- .constraints = {
- .name = "VDIG",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vpll_init = {
- .constraints = {
- .name = "VPLL",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vusb2_init = {
- .constraints = {
- .name = "VUSB2",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vvideo_init = {
- .constraints = {
- .name = "VVIDEO",
- .boot_on = 1
- }
-};
-
-static struct regulator_init_data vcam_init = {
- .constraints = {
- .name = "VCAM",
- .min_uV = 2500000,
- .max_uV = 3000000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_MODE,
- .valid_modes_mask = REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL,
- .boot_on = 1
- },
- .num_consumer_supplies = ARRAY_SIZE(vcam_consumers),
- .consumer_supplies = vcam_consumers,
-};
-
-static struct regulator_init_data vgen1_init = {
- .constraints = {
- .name = "VGEN1",
- }
-};
-
-static struct regulator_init_data vgen2_init = {
- .constraints = {
- .name = "VGEN2",
- .boot_on = 1,
- }
-};
-
-static struct regulator_init_data vgen3_init = {
- .constraints = {
- .name = "VGEN3",
- }
-};
-
-static struct mc13xxx_regulator_init_data mx35_3ds_regulators[] = {
- { .id = MC13892_SW1, .init_data = &sw1_init },
- { .id = MC13892_SW2, .init_data = &sw2_init },
- { .id = MC13892_SW3, .init_data = &sw3_init },
- { .id = MC13892_SW4, .init_data = &sw4_init },
- { .id = MC13892_VIOHI, .init_data = &viohi_init },
- { .id = MC13892_VPLL, .init_data = &vpll_init },
- { .id = MC13892_VDIG, .init_data = &vdig_init },
- { .id = MC13892_VUSB2, .init_data = &vusb2_init },
- { .id = MC13892_VVIDEO, .init_data = &vvideo_init },
- { .id = MC13892_VCAM, .init_data = &vcam_init },
- { .id = MC13892_VGEN1, .init_data = &vgen1_init },
- { .id = MC13892_VGEN2, .init_data = &vgen2_init },
- { .id = MC13892_VGEN3, .init_data = &vgen3_init },
- { .id = MC13892_VUSB, .init_data = &vusb_init },
-};
-
-static struct mc13xxx_platform_data mx35_3ds_mc13892_data = {
- .flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
- .regulators = {
- .num_regulators = ARRAY_SIZE(mx35_3ds_regulators),
- .regulators = mx35_3ds_regulators,
- },
-};
-
-#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
-
-static struct i2c_board_info mx35_3ds_i2c_mc13892 = {
-
- I2C_BOARD_INFO("mc13892", 0x08),
- .platform_data = &mx35_3ds_mc13892_data,
- /* irq number is run-time assigned */
-};
-
-static void __init imx35_3ds_init_mc13892(void)
-{
- int ret = gpio_request_one(GPIO_PMIC_INT, GPIOF_DIR_IN, "pmic irq");
-
- if (ret) {
- pr_err("failed to get pmic irq: %d\n", ret);
- return;
- }
-
- mx35_3ds_i2c_mc13892.irq = gpio_to_irq(GPIO_PMIC_INT);
- i2c_register_board_info(0, &mx35_3ds_i2c_mc13892, 1);
-}
-
-static int mx35_3ds_otg_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
-}
-
-/* OTG config */
-static const struct fsl_usb2_platform_data usb_otg_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI_WIDE,
- .workaround = FLS_USB2_WORKAROUND_ENGCM09152,
-/*
- * ENGCM09152 also requires a hardware change.
- * Please check the MX35 Chip Errata document for details.
- */
-};
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = mx35_3ds_otg_init,
- .portsc = MXC_EHCI_MODE_UTMI,
-};
-
-static int mx35_3ds_usbh_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
- MXC_EHCI_INTERNAL_PHY);
-}
-
-/* USB HOST config */
-static const struct mxc_usbh_platform_data usb_host_pdata __initconst = {
- .init = mx35_3ds_usbh_init,
- .portsc = MXC_EHCI_MODE_SERIAL,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx35_3ds_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", mx35_3ds_otg_mode);
-
-static const struct imxi2c_platform_data mx35_3ds_i2c0_data __initconst = {
- .bitrate = 100000,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init mx35_3ds_init(void)
-{
- imx35_soc_init();
-
- mxc_iomux_v3_setup_multiple_pads(mx35pdk_pads, ARRAY_SIZE(mx35pdk_pads));
-
- imx35_add_fec(NULL);
- imx35_add_imx2_wdt();
- imx35_add_mxc_rtc();
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- imx35_add_imx_uart0(&uart_pdata);
-
- if (otg_mode_host)
- imx35_add_mxc_ehci_otg(&otg_pdata);
-
- imx35_add_mxc_ehci_hs(&usb_host_pdata);
-
- if (!otg_mode_host)
- imx35_add_fsl_usb2_udc(&usb_otg_pdata);
-
- imx35_add_mxc_nand(&mx35pdk_nand_board_info);
- imx35_add_sdhci_esdhc_imx(0, NULL);
-
- imx35_add_imx_i2c0(&mx35_3ds_i2c0_data);
-
- i2c_register_board_info(
- 0, i2c_devices_3ds, ARRAY_SIZE(i2c_devices_3ds));
-
- imx35_add_ipu_core();
-}
-
-static void __init mx35_3ds_late_init(void)
-{
- struct platform_device *imx35_fb_pdev;
-
- if (mxc_expio_init(MX35_CS5_BASE_ADDR, IMX_GPIO_NR(1, 1)))
- pr_warn("Init of the debugboard failed, all "
- "devices on the debugboard are unusable.\n");
-
- imx35_fb_pdev = imx35_add_mx3_sdc_fb(&mx3fb_pdata);
- mx35_3ds_lcd.dev.parent = &imx35_fb_pdev->dev;
- platform_device_register(&mx35_3ds_lcd);
-
- imx35_3ds_init_mc13892();
-}
-
-static void __init mx35pdk_timer_init(void)
-{
- mx35_clocks_init();
-}
-
-MACHINE_START(MX35_3DS, "Freescale MX35PDK")
- /* Maintainer: Freescale Semiconductor, Inc */
- .atag_offset = 0x100,
- .map_io = mx35_map_io,
- .init_early = imx35_init_early,
- .init_irq = mx35_init_irq,
- .init_time = mx35pdk_timer_init,
- .init_machine = mx35_3ds_init,
- .init_late = mx35_3ds_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c
deleted file mode 100644
index 27a3678..0000000
--- a/arch/arm/mach-imx/mach-pca100.c
+++ /dev/null
@@ -1,426 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2007 Robert Schwebel <r.schwebel@pengutronix.de>, Pengutronix
- * Copyright (C) 2009 Sascha Hauer (kernel@pengutronix.de)
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/dma-mapping.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/eeprom.h>
-#include <linux/irq.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-#define OTG_PHY_CS_GPIO (GPIO_PORTB + 23)
-#define USBH2_PHY_CS_GPIO (GPIO_PORTB + 24)
-#define SPI1_SS0 (GPIO_PORTD + 28)
-#define SPI1_SS1 (GPIO_PORTD + 27)
-#define SD2_CD (GPIO_PORTC + 29)
-
-static const int pca100_pins[] __initconst = {
- /* UART1 */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS,
- /* SDHC */
- PB4_PF_SD2_D0,
- PB5_PF_SD2_D1,
- PB6_PF_SD2_D2,
- PB7_PF_SD2_D3,
- PB8_PF_SD2_CMD,
- PB9_PF_SD2_CLK,
- SD2_CD | GPIO_GPIO | GPIO_IN,
- /* FEC */
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_RX_CLK,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN,
- /* SSI1 */
- PC20_PF_SSI1_FS,
- PC21_PF_SSI1_RXD,
- PC22_PF_SSI1_TXD,
- PC23_PF_SSI1_CLK,
- /* onboard I2C */
- PC5_PF_I2C2_SDA,
- PC6_PF_I2C2_SCL,
- /* external I2C */
- PD17_PF_I2C_DATA,
- PD18_PF_I2C_CLK,
- /* SPI1 */
- PD25_PF_CSPI1_RDY,
- PD29_PF_CSPI1_SCLK,
- PD30_PF_CSPI1_MISO,
- PD31_PF_CSPI1_MOSI,
- /* OTG */
- OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
- PC7_PF_USBOTG_DATA5,
- PC8_PF_USBOTG_DATA6,
- PC9_PF_USBOTG_DATA0,
- PC10_PF_USBOTG_DATA2,
- PC11_PF_USBOTG_DATA1,
- PC12_PF_USBOTG_DATA4,
- PC13_PF_USBOTG_DATA3,
- PE0_PF_USBOTG_NXT,
- PE1_PF_USBOTG_STP,
- PE2_PF_USBOTG_DIR,
- PE24_PF_USBOTG_CLK,
- PE25_PF_USBOTG_DATA7,
- /* USBH2 */
- USBH2_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
- PA0_PF_USBH2_CLK,
- PA1_PF_USBH2_DIR,
- PA2_PF_USBH2_DATA7,
- PA3_PF_USBH2_NXT,
- PA4_PF_USBH2_STP,
- PD19_AF_USBH2_DATA4,
- PD20_AF_USBH2_DATA3,
- PD21_AF_USBH2_DATA6,
- PD22_AF_USBH2_DATA0,
- PD23_AF_USBH2_DATA2,
- PD24_AF_USBH2_DATA1,
- PD26_AF_USBH2_DATA5,
- /* display */
- PA5_PF_LSCLK,
- PA6_PF_LD0,
- PA7_PF_LD1,
- PA8_PF_LD2,
- PA9_PF_LD3,
- PA10_PF_LD4,
- PA11_PF_LD5,
- PA12_PF_LD6,
- PA13_PF_LD7,
- PA14_PF_LD8,
- PA15_PF_LD9,
- PA16_PF_LD10,
- PA17_PF_LD11,
- PA18_PF_LD12,
- PA19_PF_LD13,
- PA20_PF_LD14,
- PA21_PF_LD15,
- PA22_PF_LD16,
- PA23_PF_LD17,
- PA26_PF_PS,
- PA28_PF_HSYNC,
- PA29_PF_VSYNC,
- PA31_PF_OE_ACD,
- /* free GPIO */
- GPIO_PORTC | 31 | GPIO_GPIO | GPIO_IN, /* GPIO0_IRQ */
- GPIO_PORTC | 25 | GPIO_GPIO | GPIO_IN, /* GPIO1_IRQ */
- GPIO_PORTE | 5 | GPIO_GPIO | GPIO_IN, /* GPIO2_IRQ */
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-pca100_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-static const struct imxi2c_platform_data pca100_i2c1_data __initconst = {
- .bitrate = 100000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
- PROPERTY_ENTRY_U32("pagesize", 32),
- { }
-};
-
-static struct i2c_board_info pca100_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
- .properties = board_eeprom_properties,
- }, {
- I2C_BOARD_INFO("pcf8563", 0x51),
- }, {
- I2C_BOARD_INFO("lm75", 0x4a),
- }
-};
-
-static struct spi_eeprom at25320 = {
- .name = "at25320an",
- .byte_len = 4096,
- .page_size = 32,
- .flags = EE_ADDR2,
-};
-
-static struct spi_board_info pca100_spi_board_info[] __initdata = {
- {
- .modalias = "at25",
- .max_speed_hz = 30000,
- .bus_num = 0,
- .chip_select = 1,
- .platform_data = &at25320,
- },
-};
-
-static struct gpiod_lookup_table pca100_spi0_gpiod_table = {
- .dev_id = "imx27-cspi.0", /* Actual device name for spi0 */
- .table = {
- /*
- * The i.MX27 has the i.MX21 GPIO controller, port D is
- * bank 3 and thus named "imx21-gpio.3".
- * SPI1_SS0 is GPIO_PORTD + 28
- * SPI1_SS1 is GPIO_PORTD + 27
- */
- GPIO_LOOKUP_IDX("imx21-gpio.3", 28, "cs", 0, GPIO_ACTIVE_LOW),
- GPIO_LOOKUP_IDX("imx21-gpio.3", 27, "cs", 1, GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static void pca100_ac97_warm_reset(struct snd_ac97 *ac97)
-{
- mxc_gpio_mode(GPIO_PORTC | 20 | GPIO_GPIO | GPIO_OUT);
- gpio_set_value(GPIO_PORTC + 20, 1);
- udelay(2);
- gpio_set_value(GPIO_PORTC + 20, 0);
- mxc_gpio_mode(PC20_PF_SSI1_FS);
- msleep(2);
-}
-
-static void pca100_ac97_cold_reset(struct snd_ac97 *ac97)
-{
- mxc_gpio_mode(GPIO_PORTC | 20 | GPIO_GPIO | GPIO_OUT); /* FS */
- gpio_set_value(GPIO_PORTC + 20, 0);
- mxc_gpio_mode(GPIO_PORTC | 22 | GPIO_GPIO | GPIO_OUT); /* TX */
- gpio_set_value(GPIO_PORTC + 22, 0);
- mxc_gpio_mode(GPIO_PORTC | 28 | GPIO_GPIO | GPIO_OUT); /* reset */
- gpio_set_value(GPIO_PORTC + 28, 0);
- udelay(10);
- gpio_set_value(GPIO_PORTC + 28, 1);
- mxc_gpio_mode(PC20_PF_SSI1_FS);
- mxc_gpio_mode(PC22_PF_SSI1_TXD);
- msleep(2);
-}
-
-static const struct imx_ssi_platform_data pca100_ssi_pdata __initconst = {
- .ac97_reset = pca100_ac97_cold_reset,
- .ac97_warm_reset = pca100_ac97_warm_reset,
- .flags = IMX_SSI_USE_AC97,
-};
-
-static int pca100_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = request_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), detect_irq,
- IRQF_TRIGGER_FALLING, "imx-mmc-detect", data);
- if (ret)
- printk(KERN_ERR
- "pca100: Failed to request irq for sd/mmc detection\n");
-
- return ret;
-}
-
-static void pca100_sdhc2_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
- .init = pca100_sdhc2_init,
- .exit = pca100_sdhc2_exit,
-};
-
-static int otg_phy_init(struct platform_device *pdev)
-{
- gpio_set_value(OTG_PHY_CS_GPIO, 0);
-
- mdelay(10);
-
- return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = otg_phy_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static int usbh2_phy_init(struct platform_device *pdev)
-{
- gpio_set_value(USBH2_PHY_CS_GPIO, 0);
-
- mdelay(10);
-
- return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = usbh2_phy_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pca100_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", pca100_otg_mode);
-
-/* framebuffer info */
-static struct imx_fb_videomode pca100_fb_modes[] = {
- {
- .mode = {
- .name = "EMERGING-ETV570G0DHU",
- .refresh = 60,
- .xres = 640,
- .yres = 480,
- .pixclock = 39722, /* in ps (25.175 MHz) */
- .hsync_len = 30,
- .left_margin = 114,
- .right_margin = 16,
- .vsync_len = 3,
- .upper_margin = 32,
- .lower_margin = 0,
- },
- /*
- * TFT
- * Pixel pol active high
- * HSYNC active low
- * VSYNC active low
- * use HSYNC for ACD count
- * line clock disable while idle
- * always enable line clock even if no data
- */
- .pcr = 0xf0c08080,
- .bpp = 16,
- },
-};
-
-static const struct imx_fb_platform_data pca100_fb_data __initconst = {
- .mode = pca100_fb_modes,
- .num_modes = ARRAY_SIZE(pca100_fb_modes),
-
- .pwmr = 0x00A903FF,
- .lscr1 = 0x00120300,
- .dmacr = 0x00020010,
-};
-
-static void __init pca100_init(void)
-{
- int ret;
-
- imx27_soc_init();
-
- ret = mxc_gpio_setup_multiple_pins(pca100_pins,
- ARRAY_SIZE(pca100_pins), "PCA100");
- if (ret)
- printk(KERN_ERR "pca100: Failed to setup pins (%d)\n", ret);
-
- imx27_add_imx_uart0(&uart_pdata);
-
- imx27_add_mxc_nand(&pca100_nand_board_info);
-
- /* only the i2c master 1 is used on this CPU card */
- i2c_register_board_info(1, pca100_i2c_devices,
- ARRAY_SIZE(pca100_i2c_devices));
-
- imx27_add_imx_i2c(1, &pca100_i2c1_data);
-
- mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_IN);
- mxc_gpio_mode(GPIO_PORTD | 27 | GPIO_GPIO | GPIO_IN);
- spi_register_board_info(pca100_spi_board_info,
- ARRAY_SIZE(pca100_spi_board_info));
- imx27_add_spi_imx0(&pca100_spi0_gpiod_table);
-
- imx27_add_imx_fb(&pca100_fb_data);
-
- imx27_add_fec(NULL);
- imx27_add_imx2_wdt();
- imx27_add_mxc_w1();
-}
-
-static void __init pca100_late_init(void)
-{
- imx27_add_imx_ssi(0, &pca100_ssi_pdata);
-
- imx27_add_mxc_mmc(1, &sdhc_pdata);
-
- gpio_request(OTG_PHY_CS_GPIO, "usb-otg-cs");
- gpio_direction_output(OTG_PHY_CS_GPIO, 1);
- gpio_request(USBH2_PHY_CS_GPIO, "usb-host2-cs");
- gpio_direction_output(USBH2_PHY_CS_GPIO, 1);
-
- if (otg_mode_host) {
- otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
-
- if (otg_pdata.otg)
- imx27_add_mxc_ehci_otg(&otg_pdata);
- } else {
- gpio_set_value(OTG_PHY_CS_GPIO, 0);
- imx27_add_fsl_usb2_udc(&otg_device_pdata);
- }
-
- usbh2_pdata.otg = imx_otg_ulpi_create(
- ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT);
-
- if (usbh2_pdata.otg)
- imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static void __init pca100_timer_init(void)
-{
- mx27_clocks_init(26000000);
-}
-
-MACHINE_START(PCA100, "phyCARD-i.MX27")
- .atag_offset = 0x100,
- .map_io = mx27_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_machine = pca100_init,
- .init_late = pca100_late_init,
- .init_time = pca100_timer_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pcm037.c b/arch/arm/mach-imx/mach-pcm037.c
deleted file mode 100644
index c7d23e9..0000000
--- a/arch/arm/mach-imx/mach-pcm037.c
+++ /dev/null
@@ -1,585 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2008 Sascha Hauer, Pengutronix
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/delay.h>
-#include <linux/spi/spi.h>
-#include <linux/irq.h>
-#include <linux/can/platform/sja1000.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/gfp.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "pcm037.h"
-#include "ulpi.h"
-
-static enum pcm037_board_variant pcm037_instance = PCM037_PCM970;
-
-static int __init pcm037_variant_setup(char *str)
-{
- if (!strcmp("eet", str))
- pcm037_instance = PCM037_EET;
- else if (strcmp("pcm970", str))
- pr_warn("Unknown pcm037 baseboard variant %s\n", str);
-
- return 1;
-}
-
-/* Supported values: "pcm970" (default) and "eet" */
-__setup("pcm037_variant=", pcm037_variant_setup);
-
-enum pcm037_board_variant pcm037_variant(void)
-{
- return pcm037_instance;
-}
-
-/* UART1 with RTS/CTS handshake signals */
-static unsigned int pcm037_uart1_handshake_pins[] = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
-};
-
-/* UART1 without RTS/CTS handshake signals */
-static unsigned int pcm037_uart1_pins[] = {
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1,
-};
-
-static unsigned int pcm037_pins[] = {
- /* I2C */
- MX31_PIN_CSPI2_MOSI__SCL,
- MX31_PIN_CSPI2_MISO__SDA,
- MX31_PIN_CSPI2_SS2__I2C3_SDA,
- MX31_PIN_CSPI2_SCLK__I2C3_SCL,
- /* SDHC1 */
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
- IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */
- IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */
- /* SPI1 */
- MX31_PIN_CSPI1_MOSI__MOSI,
- MX31_PIN_CSPI1_MISO__MISO,
- MX31_PIN_CSPI1_SCLK__SCLK,
- MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI1_SS0__SS0,
- MX31_PIN_CSPI1_SS1__SS1,
- MX31_PIN_CSPI1_SS2__SS2,
- /* UART2 */
- MX31_PIN_TXD2__TXD2,
- MX31_PIN_RXD2__RXD2,
- MX31_PIN_CTS2__CTS2,
- MX31_PIN_RTS2__RTS2,
- /* UART3 */
- MX31_PIN_CSPI3_MOSI__RXD3,
- MX31_PIN_CSPI3_MISO__TXD3,
- MX31_PIN_CSPI3_SCLK__RTS3,
- MX31_PIN_CSPI3_SPI_RDY__CTS3,
- /* LAN9217 irq pin */
- IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO),
- /* Onewire */
- MX31_PIN_BATT_LINE__OWIRE,
- /* Framebuffer */
- MX31_PIN_LD0__LD0,
- MX31_PIN_LD1__LD1,
- MX31_PIN_LD2__LD2,
- MX31_PIN_LD3__LD3,
- MX31_PIN_LD4__LD4,
- MX31_PIN_LD5__LD5,
- MX31_PIN_LD6__LD6,
- MX31_PIN_LD7__LD7,
- MX31_PIN_LD8__LD8,
- MX31_PIN_LD9__LD9,
- MX31_PIN_LD10__LD10,
- MX31_PIN_LD11__LD11,
- MX31_PIN_LD12__LD12,
- MX31_PIN_LD13__LD13,
- MX31_PIN_LD14__LD14,
- MX31_PIN_LD15__LD15,
- MX31_PIN_LD16__LD16,
- MX31_PIN_LD17__LD17,
- MX31_PIN_VSYNC3__VSYNC3,
- MX31_PIN_HSYNC__HSYNC,
- MX31_PIN_FPSHIFT__FPSHIFT,
- MX31_PIN_DRDY0__DRDY0,
- MX31_PIN_D3_REV__D3_REV,
- MX31_PIN_CONTRAST__CONTRAST,
- MX31_PIN_D3_SPL__D3_SPL,
- MX31_PIN_D3_CLS__D3_CLS,
- MX31_PIN_LCS0__GPIO3_23,
- /* GPIO */
- IOMUX_MODE(MX31_PIN_ATA_DMACK, IOMUX_CONFIG_GPIO),
- /* OTG */
- MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
- MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
- MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
- MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
- MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
- MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
- MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
- MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
- MX31_PIN_USBOTG_CLK__USBOTG_CLK,
- MX31_PIN_USBOTG_DIR__USBOTG_DIR,
- MX31_PIN_USBOTG_NXT__USBOTG_NXT,
- MX31_PIN_USBOTG_STP__USBOTG_STP,
- /* USB host 2 */
- IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
- IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
-};
-
-static struct physmap_flash_data pcm037_flash_data = {
- .width = 2,
-};
-
-static struct resource pcm037_flash_resource = {
- .start = 0xa0000000,
- .end = 0xa1ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm037_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &pcm037_flash_data,
- },
- .resource = &pcm037_flash_resource,
- .num_resources = 1,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct resource smsc911x_resources[] = {
- {
- .start = MX31_CS1_BASE_ADDR + 0x300,
- .end = MX31_CS1_BASE_ADDR + 0x300 + SZ_64K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct smsc911x_platform_config smsc911x_info = {
- .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY |
- SMSC911X_SAVE_MAC_ADDRESS,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct platform_device pcm037_eth = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smsc911x_resources),
- .resource = smsc911x_resources,
- .dev = {
- .platform_data = &smsc911x_info,
- },
-};
-
-static struct platdata_mtd_ram pcm038_sram_data = {
- .bankwidth = 2,
-};
-
-static struct resource pcm038_sram_resource = {
- .start = MX31_CS4_BASE_ADDR,
- .end = MX31_CS4_BASE_ADDR + 512 * 1024 - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm037_sram_device = {
- .name = "mtd-ram",
- .id = 0,
- .dev = {
- .platform_data = &pcm038_sram_data,
- },
- .num_resources = 1,
- .resource = &pcm038_sram_resource,
-};
-
-static const struct mxc_nand_platform_data
-pcm037_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-static const struct imxi2c_platform_data pcm037_i2c1_data __initconst = {
- .bitrate = 100000,
-};
-
-static const struct imxi2c_platform_data pcm037_i2c2_data __initconst = {
- .bitrate = 20000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
- PROPERTY_ENTRY_U32("pagesize", 32),
- { }
-};
-
-static struct i2c_board_info pcm037_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
- .properties = board_eeprom_properties,
- }, {
- I2C_BOARD_INFO("pcf8563", 0x51),
- }
-};
-
-/* Not connected by default */
-#ifdef PCM970_SDHC_RW_SWITCH
-static int pcm970_sdhc1_get_ro(struct device *dev)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_SFS6));
-}
-#endif
-
-#define SDHC1_GPIO_WP IOMUX_TO_GPIO(MX31_PIN_SFS6)
-#define SDHC1_GPIO_DET IOMUX_TO_GPIO(MX31_PIN_SCK6)
-
-static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request(SDHC1_GPIO_DET, "sdhc-detect");
- if (ret)
- return ret;
-
- gpio_direction_input(SDHC1_GPIO_DET);
-
-#ifdef PCM970_SDHC_RW_SWITCH
- ret = gpio_request(SDHC1_GPIO_WP, "sdhc-wp");
- if (ret)
- goto err_gpio_free;
- gpio_direction_input(SDHC1_GPIO_WP);
-#endif
-
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), detect_irq,
- IRQF_TRIGGER_FALLING, "sdhc-detect", data);
- if (ret)
- goto err_gpio_free_2;
-
- return 0;
-
-err_gpio_free_2:
-#ifdef PCM970_SDHC_RW_SWITCH
- gpio_free(SDHC1_GPIO_WP);
-err_gpio_free:
-#endif
- gpio_free(SDHC1_GPIO_DET);
-
- return ret;
-}
-
-static void pcm970_sdhc1_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), data);
- gpio_free(SDHC1_GPIO_DET);
- gpio_free(SDHC1_GPIO_WP);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-#ifdef PCM970_SDHC_RW_SWITCH
- .get_ro = pcm970_sdhc1_get_ro,
-#endif
- .init = pcm970_sdhc1_init,
- .exit = pcm970_sdhc1_exit,
-};
-
-static struct platform_device *devices[] __initdata = {
- &pcm037_flash,
- &pcm037_sram_device,
-};
-
-static const struct fb_videomode fb_modedb[] = {
- {
- /* 240x320 @ 60 Hz Sharp */
- .name = "Sharp-LQ035Q7DH06-QVGA",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 185925,
- .left_margin = 9,
- .right_margin = 16,
- .upper_margin = 7,
- .lower_margin = 9,
- .hsync_len = 1,
- .vsync_len = 1,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE |
- FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }, {
- /* 240x320 @ 60 Hz */
- .name = "TX090",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 38255,
- .left_margin = 144,
- .right_margin = 0,
- .upper_margin = 7,
- .lower_margin = 40,
- .hsync_len = 96,
- .vsync_len = 1,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }, {
- /* 240x320 @ 60 Hz */
- .name = "CMEL-OLED",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 185925,
- .left_margin = 9,
- .right_margin = 16,
- .upper_margin = 7,
- .lower_margin = 9,
- .hsync_len = 1,
- .vsync_len = 1,
- .sync = FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata = {
- .name = "Sharp-LQ035Q7DH06-QVGA",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static struct resource pcm970_sja1000_resources[] = {
- {
- .start = MX31_CS5_BASE_ADDR,
- .end = MX31_CS5_BASE_ADDR + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
- },
-};
-
-static struct sja1000_platform_data pcm970_sja1000_platform_data = {
- .osc_freq = 16000000,
- .ocr = OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL,
- .cdr = CDR_CBP,
-};
-
-static struct platform_device pcm970_sja1000 = {
- .name = "sja1000_platform",
- .dev = {
- .platform_data = &pcm970_sja1000_platform_data,
- },
- .resource = pcm970_sja1000_resources,
- .num_resources = ARRAY_SIZE(pcm970_sja1000_resources),
-};
-
-static int pcm037_otg_init(struct platform_device *pdev)
-{
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = pcm037_otg_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static int pcm037_usbh2_init(struct platform_device *pdev)
-{
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
- .init = pcm037_usbh2_init,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pcm037_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", pcm037_otg_mode);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-/*
- * Board specific initialization.
- */
-static void __init pcm037_init(void)
-{
- imx31_soc_init();
-
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- mxc_iomux_set_gpr(MUX_PGP_UH2, 1);
-
- mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins),
- "pcm037");
-
-#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS \
- | PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
- mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
- mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
- mxc_iomux_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */
- mxc_iomux_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */
- mxc_iomux_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */
- mxc_iomux_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */
- mxc_iomux_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */
- mxc_iomux_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */
-
- if (pcm037_variant() == PCM037_EET)
- mxc_iomux_setup_multiple_pins(pcm037_uart1_pins,
- ARRAY_SIZE(pcm037_uart1_pins), "pcm037_uart1");
- else
- mxc_iomux_setup_multiple_pins(pcm037_uart1_handshake_pins,
- ARRAY_SIZE(pcm037_uart1_handshake_pins),
- "pcm037_uart1");
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- imx31_add_imx2_wdt();
- imx31_add_imx_uart0(&uart_pdata);
- /* XXX: should't this have .flags = 0 (i.e. no RTSCTS) on PCM037_EET? */
- imx31_add_imx_uart1(&uart_pdata);
- imx31_add_imx_uart2(&uart_pdata);
-
- imx31_add_mxc_w1();
-
- /* I2C adapters and devices */
- i2c_register_board_info(1, pcm037_i2c_devices,
- ARRAY_SIZE(pcm037_i2c_devices));
-
- imx31_add_imx_i2c1(&pcm037_i2c1_data);
- imx31_add_imx_i2c2(&pcm037_i2c2_data);
-
- imx31_add_mxc_nand(&pcm037_nand_board_info);
- imx31_add_ipu_core();
- imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
- if (otg_mode_host) {
- otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (otg_pdata.otg)
- imx31_add_mxc_ehci_otg(&otg_pdata);
- }
-
- usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (usbh2_pdata.otg)
- imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
- if (!otg_mode_host)
- imx31_add_fsl_usb2_udc(&otg_device_pdata);
-}
-
-static void __init pcm037_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-static void __init pcm037_init_late(void)
-{
- int ret;
-
- /* LAN9217 IRQ pin */
- ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq");
- if (!ret) {
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
- smsc911x_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
- smsc911x_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
- platform_device_register(&pcm037_eth);
- } else {
- pr_warn("could not get LAN irq gpio\n");
- }
-
- imx31_add_mxc_mmc(0, &sdhc_pdata);
-
- pcm970_sja1000_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105)));
- pcm970_sja1000_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105)));
- platform_device_register(&pcm970_sja1000);
-
- pcm037_eet_init_devices();
-}
-
-MACHINE_START(PCM037, "Phytec Phycore pcm037")
- /* Maintainer: Pengutronix */
- .atag_offset = 0x100,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = pcm037_timer_init,
- .init_machine = pcm037_init,
- .init_late = pcm037_init_late,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pcm037_eet.c b/arch/arm/mach-imx/mach-pcm037_eet.c
deleted file mode 100644
index 8b0e03a..0000000
--- a/arch/arm/mach-imx/mach-pcm037_eet.c
+++ /dev/null
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009
- * Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
- */
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-
-#include <asm/mach-types.h>
-
-#include "pcm037.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "iomux-mx3.h"
-
-static unsigned int pcm037_eet_pins[] = {
- /* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */
- IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
- /* GPIO keys */
- IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO), /* 0 */
- IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO), /* 1 */
- IOMUX_MODE(MX31_PIN_GPIO1_2, IOMUX_CONFIG_GPIO), /* 2 */
- IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO), /* 3 */
- IOMUX_MODE(MX31_PIN_SVEN0, IOMUX_CONFIG_GPIO), /* 32 */
- IOMUX_MODE(MX31_PIN_STX0, IOMUX_CONFIG_GPIO), /* 33 */
- IOMUX_MODE(MX31_PIN_SRX0, IOMUX_CONFIG_GPIO), /* 34 */
- IOMUX_MODE(MX31_PIN_SIMPD0, IOMUX_CONFIG_GPIO), /* 35 */
- IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_GPIO), /* 38 */
- IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_GPIO), /* 39 */
- IOMUX_MODE(MX31_PIN_KEY_ROW4, IOMUX_CONFIG_GPIO), /* 50 */
- IOMUX_MODE(MX31_PIN_KEY_ROW5, IOMUX_CONFIG_GPIO), /* 51 */
- IOMUX_MODE(MX31_PIN_KEY_ROW6, IOMUX_CONFIG_GPIO), /* 52 */
- IOMUX_MODE(MX31_PIN_KEY_ROW7, IOMUX_CONFIG_GPIO), /* 53 */
-
- /* LEDs */
- IOMUX_MODE(MX31_PIN_DTR_DTE1, IOMUX_CONFIG_GPIO), /* 44 */
- IOMUX_MODE(MX31_PIN_DSR_DTE1, IOMUX_CONFIG_GPIO), /* 45 */
- IOMUX_MODE(MX31_PIN_KEY_COL5, IOMUX_CONFIG_GPIO), /* 55 */
- IOMUX_MODE(MX31_PIN_KEY_COL6, IOMUX_CONFIG_GPIO), /* 56 */
-};
-
-/* SPI */
-static struct spi_board_info pcm037_spi_dev[] = {
- {
- .modalias = "dac124s085",
- .max_speed_hz = 400000,
- .bus_num = 0,
- .chip_select = 1, /* Index in pcm037_spi1_cs[] */
- .mode = SPI_CPHA,
- },
-};
-
-/* GPIO-keys input device */
-static struct gpio_keys_button pcm037_gpio_keys[] = {
- {
- .type = EV_KEY,
- .code = KEY_L,
- .gpio = 0,
- .desc = "Wheel Manual",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_A,
- .gpio = 1,
- .desc = "Wheel AF",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_V,
- .gpio = 2,
- .desc = "Wheel View",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_M,
- .gpio = 3,
- .desc = "Wheel Menu",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_UP,
- .gpio = 32,
- .desc = "Nav Pad Up",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_RIGHT,
- .gpio = 33,
- .desc = "Nav Pad Right",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_DOWN,
- .gpio = 34,
- .desc = "Nav Pad Down",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_LEFT,
- .gpio = 35,
- .desc = "Nav Pad Left",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_ENTER,
- .gpio = 38,
- .desc = "Nav Pad Ok",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = KEY_O,
- .gpio = 39,
- .desc = "Wheel Off",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = BTN_FORWARD,
- .gpio = 50,
- .desc = "Focus Forward",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = BTN_BACK,
- .gpio = 51,
- .desc = "Focus Backward",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = BTN_MIDDLE,
- .gpio = 52,
- .desc = "Release Half",
- .wakeup = 0,
- }, {
- .type = EV_KEY,
- .code = BTN_EXTRA,
- .gpio = 53,
- .desc = "Release Full",
- .wakeup = 0,
- },
-};
-
-static const struct gpio_keys_platform_data
- pcm037_gpio_keys_platform_data __initconst = {
- .buttons = pcm037_gpio_keys,
- .nbuttons = ARRAY_SIZE(pcm037_gpio_keys),
- .rep = 0, /* No auto-repeat */
-};
-
-int __init pcm037_eet_init_devices(void)
-{
- if (pcm037_variant() != PCM037_EET)
- return 0;
-
- mxc_iomux_setup_multiple_pins(pcm037_eet_pins,
- ARRAY_SIZE(pcm037_eet_pins), "pcm037_eet");
-
- /* SPI */
- spi_register_board_info(pcm037_spi_dev, ARRAY_SIZE(pcm037_spi_dev));
- imx31_add_spi_imx0(NULL);
-
- imx_add_gpio_keys(&pcm037_gpio_keys_platform_data);
-
- return 0;
-}
diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c
deleted file mode 100644
index 017a501..0000000
--- a/arch/arm/mach-imx/mach-pcm043.c
+++ /dev/null
@@ -1,412 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Sascha Hauer, Pengutronix
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/smc911x.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-#include "ulpi.h"
-
-static const struct fb_videomode fb_modedb[] = {
- {
- /* 240x320 @ 60 Hz */
- .name = "Sharp-LQ035Q7",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 185925,
- .left_margin = 9,
- .right_margin = 16,
- .upper_margin = 7,
- .lower_margin = 9,
- .hsync_len = 1,
- .vsync_len = 1,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }, {
- /* 240x320 @ 60 Hz */
- .name = "TX090",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 38255,
- .left_margin = 144,
- .right_margin = 0,
- .upper_margin = 7,
- .lower_margin = 40,
- .hsync_len = 96,
- .vsync_len = 1,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "Sharp-LQ035Q7",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static struct physmap_flash_data pcm043_flash_data = {
- .width = 2,
-};
-
-static struct resource pcm043_flash_resource = {
- .start = 0xa0000000,
- .end = 0xa1ffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm043_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &pcm043_flash_data,
- },
- .resource = &pcm043_flash_resource,
- .num_resources = 1,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data pcm043_i2c0_data __initconst = {
- .bitrate = 50000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
- PROPERTY_ENTRY_U32("pagesize", 32),
- { }
-};
-
-static struct i2c_board_info pcm043_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
- .properties = board_eeprom_properties,
- }, {
- I2C_BOARD_INFO("pcf8563", 0x51),
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &pcm043_flash,
-};
-
-static const iomux_v3_cfg_t pcm043_pads[] __initconst = {
- /* UART1 */
- MX35_PAD_CTS1__UART1_CTS,
- MX35_PAD_RTS1__UART1_RTS,
- MX35_PAD_TXD1__UART1_TXD_MUX,
- MX35_PAD_RXD1__UART1_RXD_MUX,
- /* UART2 */
- MX35_PAD_CTS2__UART2_CTS,
- MX35_PAD_RTS2__UART2_RTS,
- MX35_PAD_TXD2__UART2_TXD_MUX,
- MX35_PAD_RXD2__UART2_RXD_MUX,
- /* FEC */
- MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
- MX35_PAD_FEC_RX_DV__FEC_RX_DV,
- MX35_PAD_FEC_COL__FEC_COL,
- MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
- MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
- MX35_PAD_FEC_TX_EN__FEC_TX_EN,
- MX35_PAD_FEC_MDC__FEC_MDC,
- MX35_PAD_FEC_MDIO__FEC_MDIO,
- MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
- MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
- MX35_PAD_FEC_CRS__FEC_CRS,
- MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
- MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
- MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
- MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
- MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
- MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
- /* I2C1 */
- MX35_PAD_I2C1_CLK__I2C1_SCL,
- MX35_PAD_I2C1_DAT__I2C1_SDA,
- /* Display */
- MX35_PAD_LD0__IPU_DISPB_DAT_0,
- MX35_PAD_LD1__IPU_DISPB_DAT_1,
- MX35_PAD_LD2__IPU_DISPB_DAT_2,
- MX35_PAD_LD3__IPU_DISPB_DAT_3,
- MX35_PAD_LD4__IPU_DISPB_DAT_4,
- MX35_PAD_LD5__IPU_DISPB_DAT_5,
- MX35_PAD_LD6__IPU_DISPB_DAT_6,
- MX35_PAD_LD7__IPU_DISPB_DAT_7,
- MX35_PAD_LD8__IPU_DISPB_DAT_8,
- MX35_PAD_LD9__IPU_DISPB_DAT_9,
- MX35_PAD_LD10__IPU_DISPB_DAT_10,
- MX35_PAD_LD11__IPU_DISPB_DAT_11,
- MX35_PAD_LD12__IPU_DISPB_DAT_12,
- MX35_PAD_LD13__IPU_DISPB_DAT_13,
- MX35_PAD_LD14__IPU_DISPB_DAT_14,
- MX35_PAD_LD15__IPU_DISPB_DAT_15,
- MX35_PAD_LD16__IPU_DISPB_DAT_16,
- MX35_PAD_LD17__IPU_DISPB_DAT_17,
- MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
- MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
- MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
- MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
- MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
- MX35_PAD_D3_REV__IPU_DISPB_D3_REV,
- MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS,
- /* gpio */
- MX35_PAD_ATA_CS0__GPIO2_6,
- /* USB host */
- MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR,
- MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC,
- /* SSI */
- MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS,
- MX35_PAD_STXD4__AUDMUX_AUD4_TXD,
- MX35_PAD_SRXD4__AUDMUX_AUD4_RXD,
- MX35_PAD_SCK4__AUDMUX_AUD4_TXC,
- /* CAN2 */
- MX35_PAD_TX5_RX0__CAN2_TXCAN,
- MX35_PAD_TX4_RX1__CAN2_RXCAN,
- /* esdhc */
- MX35_PAD_SD1_CMD__ESDHC1_CMD,
- MX35_PAD_SD1_CLK__ESDHC1_CLK,
- MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
- MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
- MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
- MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
- MX35_PAD_ATA_DATA10__GPIO2_23, /* WriteProtect */
- MX35_PAD_ATA_DATA11__GPIO2_24, /* CardDetect */
-};
-
-#define AC97_GPIO_TXFS IMX_GPIO_NR(2, 31)
-#define AC97_GPIO_TXD IMX_GPIO_NR(2, 28)
-#define AC97_GPIO_RESET IMX_GPIO_NR(2, 0)
-
-static void pcm043_ac97_warm_reset(struct snd_ac97 *ac97)
-{
- iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31;
- iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS;
- int ret;
-
- ret = gpio_request(AC97_GPIO_TXFS, "SSI");
- if (ret) {
- printk("failed to get GPIO_TXFS: %d\n", ret);
- return;
- }
-
- mxc_iomux_v3_setup_pad(txfs_gpio);
-
- /* warm reset */
- gpio_direction_output(AC97_GPIO_TXFS, 1);
- udelay(2);
- gpio_set_value(AC97_GPIO_TXFS, 0);
-
- gpio_free(AC97_GPIO_TXFS);
- mxc_iomux_v3_setup_pad(txfs);
-}
-
-static void pcm043_ac97_cold_reset(struct snd_ac97 *ac97)
-{
- iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31;
- iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS;
- iomux_v3_cfg_t txd_gpio = MX35_PAD_STXD4__GPIO2_28;
- iomux_v3_cfg_t txd = MX35_PAD_STXD4__AUDMUX_AUD4_TXD;
- iomux_v3_cfg_t reset_gpio = MX35_PAD_SD2_CMD__GPIO2_0;
- int ret;
-
- ret = gpio_request(AC97_GPIO_TXFS, "SSI");
- if (ret)
- goto err1;
-
- ret = gpio_request(AC97_GPIO_TXD, "SSI");
- if (ret)
- goto err2;
-
- ret = gpio_request(AC97_GPIO_RESET, "SSI");
- if (ret)
- goto err3;
-
- mxc_iomux_v3_setup_pad(txfs_gpio);
- mxc_iomux_v3_setup_pad(txd_gpio);
- mxc_iomux_v3_setup_pad(reset_gpio);
-
- gpio_direction_output(AC97_GPIO_TXFS, 0);
- gpio_direction_output(AC97_GPIO_TXD, 0);
-
- /* cold reset */
- gpio_direction_output(AC97_GPIO_RESET, 0);
- udelay(10);
- gpio_direction_output(AC97_GPIO_RESET, 1);
-
- mxc_iomux_v3_setup_pad(txd);
- mxc_iomux_v3_setup_pad(txfs);
-
- gpio_free(AC97_GPIO_RESET);
-err3:
- gpio_free(AC97_GPIO_TXD);
-err2:
- gpio_free(AC97_GPIO_TXFS);
-err1:
- if (ret)
- printk("%s failed with %d\n", __func__, ret);
- mdelay(1);
-}
-
-static const struct imx_ssi_platform_data pcm043_ssi_pdata __initconst = {
- .ac97_reset = pcm043_ac97_cold_reset,
- .ac97_warm_reset = pcm043_ac97_warm_reset,
- .flags = IMX_SSI_USE_AC97,
-};
-
-static const struct mxc_nand_platform_data
-pcm037_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
-};
-
-static int pcm043_otg_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
- .init = pcm043_otg_init,
- .portsc = MXC_EHCI_MODE_UTMI,
-};
-
-static int pcm043_usbh1_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
- MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN);
-}
-
-static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
- .init = pcm043_usbh1_init,
- .portsc = MXC_EHCI_MODE_SERIAL,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pcm043_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", pcm043_otg_mode);
-
-static struct esdhc_platform_data sd1_pdata = {
- .wp_type = ESDHC_WP_GPIO,
- .cd_type = ESDHC_CD_GPIO,
-};
-
-static struct gpiod_lookup_table sd1_gpio_table = {
- .dev_id = "sdhci-esdhc-imx35.0",
- .table = {
- /* Card detect: bank 2 offset 24 */
- GPIO_LOOKUP("imx35-gpio.2", 24, "cd", GPIO_ACTIVE_LOW),
- /* Write protect: bank 2 offset 23 */
- GPIO_LOOKUP("imx35-gpio.2", 23, "wp", GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-/*
- * Board specific initialization.
- */
-static void __init pcm043_init(void)
-{
- imx35_soc_init();
-
- mxc_iomux_v3_setup_multiple_pads(pcm043_pads, ARRAY_SIZE(pcm043_pads));
-
- imx35_add_fec(NULL);
- platform_add_devices(devices, ARRAY_SIZE(devices));
- imx35_add_imx2_wdt();
-
- imx35_add_imx_uart0(&uart_pdata);
- imx35_add_mxc_nand(&pcm037_nand_board_info);
-
- imx35_add_imx_uart1(&uart_pdata);
-
- i2c_register_board_info(0, pcm043_i2c_devices,
- ARRAY_SIZE(pcm043_i2c_devices));
-
- imx35_add_imx_i2c0(&pcm043_i2c0_data);
-
- imx35_add_ipu_core();
- imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-
- if (otg_mode_host) {
- otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (otg_pdata.otg)
- imx35_add_mxc_ehci_otg(&otg_pdata);
- }
- imx35_add_mxc_ehci_hs(&usbh1_pdata);
-
- if (!otg_mode_host)
- imx35_add_fsl_usb2_udc(&otg_device_pdata);
-
- imx35_add_flexcan1();
-}
-
-static void __init pcm043_late_init(void)
-{
- imx35_add_imx_ssi(0, &pcm043_ssi_pdata);
-
- gpiod_add_lookup_table(&sd1_gpio_table);
- imx35_add_sdhci_esdhc_imx(0, &sd1_pdata);
-}
-
-static void __init pcm043_timer_init(void)
-{
- mx35_clocks_init();
-}
-
-MACHINE_START(PCM043, "Phytec Phycore pcm043")
- /* Maintainer: Pengutronix */
- .atag_offset = 0x100,
- .map_io = mx35_map_io,
- .init_early = imx35_init_early,
- .init_irq = mx35_init_irq,
- .init_time = pcm043_timer_init,
- .init_machine = pcm043_init,
- .init_late = pcm043_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-qong.c b/arch/arm/mach-imx/mach-qong.c
deleted file mode 100644
index 5b362da..0000000
--- a/arch/arm/mach-imx/mach-qong.c
+++ /dev/null
@@ -1,262 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Ilya Yanok, Emcraft Systems Ltd, <yanok@emcraft.com>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/memory.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/platnand.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/page.h>
-#include <asm/setup.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/* FPGA defines */
-#define QONG_FPGA_VERSION(major, minor, rev) \
- (((major & 0xF) << 12) | ((minor & 0xF) << 8) | (rev & 0xFF))
-
-#define QONG_FPGA_BASEADDR MX31_CS1_BASE_ADDR
-#define QONG_FPGA_PERIPH_SIZE (1 << 24)
-
-#define QONG_FPGA_CTRL_BASEADDR QONG_FPGA_BASEADDR
-#define QONG_FPGA_CTRL_SIZE 0x10
-/* FPGA control registers */
-#define QONG_FPGA_CTRL_VERSION 0x00
-
-#define QONG_DNET_ID 1
-#define QONG_DNET_BASEADDR \
- (QONG_FPGA_BASEADDR + QONG_DNET_ID * QONG_FPGA_PERIPH_SIZE)
-#define QONG_DNET_SIZE 0x00001000
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static int uart_pins[] = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1
-};
-
-static inline void __init mxc_init_imx_uart(void)
-{
- mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins),
- "uart-0");
- imx31_add_imx_uart0(&uart_pdata);
-}
-
-static struct resource dnet_resources[] = {
- {
- .name = "dnet-memory",
- .start = QONG_DNET_BASEADDR,
- .end = QONG_DNET_BASEADDR + QONG_DNET_SIZE - 1,
- .flags = IORESOURCE_MEM,
- }, {
- /* irq number is run-time assigned */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device dnet_device = {
- .name = "dnet",
- .id = -1,
- .num_resources = ARRAY_SIZE(dnet_resources),
- .resource = dnet_resources,
-};
-
-static int __init qong_init_dnet(void)
-{
- int ret;
-
- dnet_resources[1].start =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1));
- dnet_resources[1].end =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1));
- ret = platform_device_register(&dnet_device);
- return ret;
-}
-
-/* MTD NOR flash */
-
-static struct physmap_flash_data qong_flash_data = {
- .width = 2,
-};
-
-static struct resource qong_flash_resource = {
- .start = MX31_CS0_BASE_ADDR,
- .end = MX31_CS0_BASE_ADDR + SZ_128M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device qong_nor_mtd_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &qong_flash_data,
- },
- .resource = &qong_flash_resource,
- .num_resources = 1,
-};
-
-static void qong_init_nor_mtd(void)
-{
- (void)platform_device_register(&qong_nor_mtd_device);
-}
-
-/*
- * Hardware specific access to control-lines
- */
-static void qong_nand_cmd_ctrl(struct nand_chip *nand_chip, int cmd,
- unsigned int ctrl)
-{
- if (cmd == NAND_CMD_NONE)
- return;
-
- if (ctrl & NAND_CLE)
- writeb(cmd, nand_chip->legacy.IO_ADDR_W + (1 << 24));
- else
- writeb(cmd, nand_chip->legacy.IO_ADDR_W + (1 << 23));
-}
-
-/*
- * Read the Device Ready pin.
- */
-static int qong_nand_device_ready(struct nand_chip *chip)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_NFRB));
-}
-
-static void qong_nand_select_chip(struct nand_chip *chip, int cs)
-{
- if (cs >= 0)
- gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 0);
- else
- gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 1);
-}
-
-static struct platform_nand_data qong_nand_data = {
- .chip = {
- .nr_chips = 1,
- .chip_delay = 20,
- .options = 0,
- },
- .ctrl = {
- .cmd_ctrl = qong_nand_cmd_ctrl,
- .dev_ready = qong_nand_device_ready,
- .select_chip = qong_nand_select_chip,
- }
-};
-
-static struct resource qong_nand_resource = {
- .start = MX31_CS3_BASE_ADDR,
- .end = MX31_CS3_BASE_ADDR + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device qong_nand_device = {
- .name = "gen_nand",
- .id = -1,
- .dev = {
- .platform_data = &qong_nand_data,
- },
- .num_resources = 1,
- .resource = &qong_nand_resource,
-};
-
-static void __init qong_init_nand_mtd(void)
-{
- /* init CS */
- imx_writel(0x00004f00, MX31_IO_ADDRESS(MX31_WEIM_CSCRxU(3)));
- imx_writel(0x20013b31, MX31_IO_ADDRESS(MX31_WEIM_CSCRxL(3)));
- imx_writel(0x00020800, MX31_IO_ADDRESS(MX31_WEIM_CSCRxA(3)));
-
- mxc_iomux_set_gpr(MUX_SDCTL_CSD1_SEL, true);
-
- /* enable pin */
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFCE_B, IOMUX_CONFIG_GPIO));
- if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), "nand_enable"))
- gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 0);
-
- /* ready/busy pin */
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFRB, IOMUX_CONFIG_GPIO));
- if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFRB), "nand_rdy"))
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFRB));
-
- /* write protect pin */
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFWP_B, IOMUX_CONFIG_GPIO));
- if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFWP_B), "nand_wp"))
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFWP_B));
-
- platform_device_register(&qong_nand_device);
-}
-
-static void __init qong_init_fpga(void)
-{
- void __iomem *regs;
- u32 fpga_ver;
-
- regs = ioremap(QONG_FPGA_CTRL_BASEADDR, QONG_FPGA_CTRL_SIZE);
- if (!regs) {
- printk(KERN_ERR "%s: failed to map registers, aborting.\n",
- __func__);
- return;
- }
-
- fpga_ver = readl(regs + QONG_FPGA_CTRL_VERSION);
- iounmap(regs);
- printk(KERN_INFO "Qong FPGA version %d.%d.%d\n",
- (fpga_ver & 0xF000) >> 12,
- (fpga_ver & 0x0F00) >> 8, fpga_ver & 0x00FF);
- if (fpga_ver < QONG_FPGA_VERSION(0, 8, 7)) {
- printk(KERN_ERR "qong: Unexpected FPGA version, FPGA-based "
- "devices won't be registered!\n");
- return;
- }
-
- /* register FPGA-based devices */
- qong_init_nand_mtd();
- qong_init_dnet();
-}
-
-/*
- * Board specific initialization.
- */
-static void __init qong_init(void)
-{
- imx31_soc_init();
-
- mxc_init_imx_uart();
- qong_init_nor_mtd();
- imx31_add_imx2_wdt();
-}
-
-static void __init qong_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(QONG, "Dave/DENX QongEVB-LITE")
- /* Maintainer: DENX Software Engineering GmbH */
- .atag_offset = 0x100,
- .map_io = mx31_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = qong_timer_init,
- .init_machine = qong_init,
- .init_late = qong_init_fpga,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c
deleted file mode 100644
index fae5a41..0000000
--- a/arch/arm/mach-imx/mach-vpr200.c
+++ /dev/null
@@ -1,306 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Marc Kleine-Budde, Pengutronix
- * Copyright 2010 Creative Product Design
- *
- * Derived from mx35 3stack.
- * Original author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include <linux/i2c.h>
-#include <linux/mfd/mc13xxx.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-#define GPIO_LCDPWR IMX_GPIO_NR(1, 2)
-#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
-
-#define GPIO_BUTTON1 IMX_GPIO_NR(1, 4)
-#define GPIO_BUTTON2 IMX_GPIO_NR(1, 5)
-#define GPIO_BUTTON3 IMX_GPIO_NR(1, 7)
-#define GPIO_BUTTON4 IMX_GPIO_NR(1, 8)
-#define GPIO_BUTTON5 IMX_GPIO_NR(1, 9)
-#define GPIO_BUTTON6 IMX_GPIO_NR(1, 10)
-#define GPIO_BUTTON7 IMX_GPIO_NR(1, 11)
-#define GPIO_BUTTON8 IMX_GPIO_NR(1, 12)
-
-static const struct fb_videomode fb_modedb[] = {
- {
- /* 800x480 @ 60 Hz */
- .name = "PT0708048",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = KHZ2PICOS(33260),
- .left_margin = 50,
- .right_margin = 156,
- .upper_margin = 10,
- .lower_margin = 10,
- .hsync_len = 1, /* note: DE only display */
- .vsync_len = 1, /* note: DE only display */
- .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }, {
- /* 800x480 @ 60 Hz */
- .name = "CTP-CLAA070LC0ACW",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = KHZ2PICOS(27000),
- .left_margin = 50,
- .right_margin = 50, /* whole line should have 900 clocks */
- .upper_margin = 10,
- .lower_margin = 10, /* whole frame should have 500 lines */
- .hsync_len = 1, /* note: DE only display */
- .vsync_len = 1, /* note: DE only display */
- .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- }
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
- .name = "PT0708048",
- .mode = fb_modedb,
- .num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static struct physmap_flash_data vpr200_flash_data = {
- .width = 2,
-};
-
-static struct resource vpr200_flash_resource = {
- .start = MX35_CS0_BASE_ADDR,
- .end = MX35_CS0_BASE_ADDR + SZ_64M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device vpr200_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &vpr200_flash_data,
- },
- .resource = &vpr200_flash_resource,
- .num_resources = 1,
-};
-
-static const struct mxc_nand_platform_data
- vpr200_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
- .flash_bbt = 1,
-};
-
-#define VPR_KEY_DEBOUNCE 500
-static struct gpio_keys_button vpr200_gpio_keys_table[] = {
- {KEY_F2, GPIO_BUTTON1, 1, "vpr-keys: F2", 0, VPR_KEY_DEBOUNCE},
- {KEY_F3, GPIO_BUTTON2, 1, "vpr-keys: F3", 0, VPR_KEY_DEBOUNCE},
- {KEY_F4, GPIO_BUTTON3, 1, "vpr-keys: F4", 0, VPR_KEY_DEBOUNCE},
- {KEY_F5, GPIO_BUTTON4, 1, "vpr-keys: F5", 0, VPR_KEY_DEBOUNCE},
- {KEY_F6, GPIO_BUTTON5, 1, "vpr-keys: F6", 0, VPR_KEY_DEBOUNCE},
- {KEY_F7, GPIO_BUTTON6, 1, "vpr-keys: F7", 0, VPR_KEY_DEBOUNCE},
- {KEY_F8, GPIO_BUTTON7, 1, "vpr-keys: F8", 1, VPR_KEY_DEBOUNCE},
- {KEY_F9, GPIO_BUTTON8, 1, "vpr-keys: F9", 1, VPR_KEY_DEBOUNCE},
-};
-
-static const struct gpio_keys_platform_data
- vpr200_gpio_keys_data __initconst = {
- .buttons = vpr200_gpio_keys_table,
- .nbuttons = ARRAY_SIZE(vpr200_gpio_keys_table),
-};
-
-static struct mc13xxx_platform_data vpr200_pmic = {
- .flags = MC13XXX_USE_ADC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static const struct imxi2c_platform_data vpr200_i2c0_data __initconst = {
- .bitrate = 50000,
-};
-
-static struct i2c_board_info vpr200_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c02", 0x50), /* E0=0, E1=0, E2=0 */
- }, {
- I2C_BOARD_INFO("mc13892", 0x08),
- .platform_data = &vpr200_pmic,
- /* irq number is run-time assigned */
- }
-};
-
-static const iomux_v3_cfg_t vpr200_pads[] __initconst = {
- /* UART1 */
- MX35_PAD_TXD1__UART1_TXD_MUX,
- MX35_PAD_RXD1__UART1_RXD_MUX,
- /* UART3 */
- MX35_PAD_ATA_DATA10__UART3_RXD_MUX,
- MX35_PAD_ATA_DATA11__UART3_TXD_MUX,
- /* FEC */
- MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
- MX35_PAD_FEC_RX_DV__FEC_RX_DV,
- MX35_PAD_FEC_COL__FEC_COL,
- MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
- MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
- MX35_PAD_FEC_TX_EN__FEC_TX_EN,
- MX35_PAD_FEC_MDC__FEC_MDC,
- MX35_PAD_FEC_MDIO__FEC_MDIO,
- MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
- MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
- MX35_PAD_FEC_CRS__FEC_CRS,
- MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
- MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
- MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
- MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
- MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
- MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
- /* Display */
- MX35_PAD_LD0__IPU_DISPB_DAT_0,
- MX35_PAD_LD1__IPU_DISPB_DAT_1,
- MX35_PAD_LD2__IPU_DISPB_DAT_2,
- MX35_PAD_LD3__IPU_DISPB_DAT_3,
- MX35_PAD_LD4__IPU_DISPB_DAT_4,
- MX35_PAD_LD5__IPU_DISPB_DAT_5,
- MX35_PAD_LD6__IPU_DISPB_DAT_6,
- MX35_PAD_LD7__IPU_DISPB_DAT_7,
- MX35_PAD_LD8__IPU_DISPB_DAT_8,
- MX35_PAD_LD9__IPU_DISPB_DAT_9,
- MX35_PAD_LD10__IPU_DISPB_DAT_10,
- MX35_PAD_LD11__IPU_DISPB_DAT_11,
- MX35_PAD_LD12__IPU_DISPB_DAT_12,
- MX35_PAD_LD13__IPU_DISPB_DAT_13,
- MX35_PAD_LD14__IPU_DISPB_DAT_14,
- MX35_PAD_LD15__IPU_DISPB_DAT_15,
- MX35_PAD_LD16__IPU_DISPB_DAT_16,
- MX35_PAD_LD17__IPU_DISPB_DAT_17,
- MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
- MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
- MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
- /* LCD Enable */
- MX35_PAD_D3_VSYNC__GPIO1_2,
- /* USBOTG */
- MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
- MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
- /* SDCARD */
- MX35_PAD_SD1_CMD__ESDHC1_CMD,
- MX35_PAD_SD1_CLK__ESDHC1_CLK,
- MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
- MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
- MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
- MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
- /* PMIC */
- MX35_PAD_GPIO2_0__GPIO2_0,
- /* GPIO keys */
- MX35_PAD_SCKR__GPIO1_4,
- MX35_PAD_COMPARE__GPIO1_5,
- MX35_PAD_SCKT__GPIO1_7,
- MX35_PAD_FST__GPIO1_8,
- MX35_PAD_HCKT__GPIO1_9,
- MX35_PAD_TX5_RX0__GPIO1_10,
- MX35_PAD_TX4_RX1__GPIO1_11,
- MX35_PAD_TX3_RX2__GPIO1_12,
-};
-
-/* USB Device config */
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI,
- .workaround = FLS_USB2_WORKAROUND_ENGCM09152,
-};
-
-static int vpr200_usbh_init(struct platform_device *pdev)
-{
- return mx35_initialize_usb_hw(pdev->id,
- MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY);
-}
-
-/* USB HOST config */
-static const struct mxc_usbh_platform_data usb_host_pdata __initconst = {
- .init = vpr200_usbh_init,
- .portsc = MXC_EHCI_MODE_SERIAL,
-};
-
-static struct platform_device *devices[] __initdata = {
- &vpr200_flash,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init vpr200_board_init(void)
-{
- imx35_soc_init();
-
- mxc_iomux_v3_setup_multiple_pads(vpr200_pads, ARRAY_SIZE(vpr200_pads));
-
- imx35_add_fec(NULL);
- imx35_add_imx2_wdt();
-
- imx35_add_imx_uart0(NULL);
- imx35_add_imx_uart2(NULL);
-
- imx35_add_ipu_core();
- imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-
- imx35_add_fsl_usb2_udc(&otg_device_pdata);
- imx35_add_mxc_ehci_hs(&usb_host_pdata);
-
- imx35_add_mxc_nand(&vpr200_nand_board_info);
- imx35_add_sdhci_esdhc_imx(0, NULL);
-}
-
-static void __init vpr200_late_init(void)
-{
- imx_add_gpio_keys(&vpr200_gpio_keys_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- if (0 != gpio_request(GPIO_LCDPWR, "LCDPWR"))
- printk(KERN_WARNING "vpr200: Couldn't get LCDPWR gpio\n");
- else
- gpio_direction_output(GPIO_LCDPWR, 0);
-
- if (0 != gpio_request(GPIO_PMIC_INT, "PMIC_INT"))
- printk(KERN_WARNING "vpr200: Couldn't get PMIC_INT gpio\n");
- else
- gpio_direction_input(GPIO_PMIC_INT);
-
- vpr200_i2c_devices[1].irq = gpio_to_irq(GPIO_PMIC_INT);
- i2c_register_board_info(0, vpr200_i2c_devices,
- ARRAY_SIZE(vpr200_i2c_devices));
-
- imx35_add_imx_i2c0(&vpr200_i2c0_data);
-}
-
-static void __init vpr200_timer_init(void)
-{
- mx35_clocks_init();
-}
-
-MACHINE_START(VPR200, "VPR200")
- /* Maintainer: Creative Product Design */
- .map_io = mx35_map_io,
- .init_early = imx35_init_early,
- .init_irq = mx35_init_irq,
- .init_time = vpr200_timer_init,
- .init_machine = vpr200_board_init,
- .init_late = vpr200_late_init,
- .restart = mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mm-imx21.c b/arch/arm/mach-imx/mm-imx21.c
deleted file mode 100644
index b834026..0000000
--- a/arch/arm/mach-imx/mm-imx21.c
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/mach-imx/mm-imx21.c
- *
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/pinctrl/machine.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices/devices-common.h"
-#include "hardware.h"
-#include "iomux-v1.h"
-
-/* MX21 memory map definition */
-static struct map_desc imx21_io_desc[] __initdata = {
- /*
- * this fixed mapping covers:
- * - AIPI1
- * - AIPI2
- * - AITC
- * - ROM Patch
- * - and some reserved space
- */
- imx_map_entry(MX21, AIPI, MT_DEVICE),
- /*
- * this fixed mapping covers:
- * - CSI
- * - ATA
- */
- imx_map_entry(MX21, SAHB1, MT_DEVICE),
- /*
- * this fixed mapping covers:
- * - EMI
- */
- imx_map_entry(MX21, X_MEMC, MT_DEVICE),
-};
-
-/*
- * Initialize the memory map. It is called during the
- * system startup to create static physical to virtual
- * memory map for the IO modules.
- */
-void __init mx21_map_io(void)
-{
- iotable_init(imx21_io_desc, ARRAY_SIZE(imx21_io_desc));
-}
-
-void __init imx21_init_early(void)
-{
- mxc_set_cpu_type(MXC_CPU_MX21);
- imx_iomuxv1_init(MX21_IO_ADDRESS(MX21_GPIO_BASE_ADDR),
- MX21_NUM_GPIO_PORT);
-}
-
-void __init mx21_init_irq(void)
-{
- mxc_init_irq(MX21_IO_ADDRESS(MX21_AVIC_BASE_ADDR));
-}
-
-static const struct resource imx21_audmux_res[] __initconst = {
- DEFINE_RES_MEM(MX21_AUDMUX_BASE_ADDR, SZ_4K),
-};
-
-void __init imx21_soc_init(void)
-{
- mxc_arch_reset_init(MX21_IO_ADDRESS(MX21_WDOG_BASE_ADDR));
- mxc_device_init();
-
- mxc_register_gpio("imx21-gpio", 0, MX21_GPIO1_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 1, MX21_GPIO2_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 2, MX21_GPIO3_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 3, MX21_GPIO4_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 4, MX21_GPIO5_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 5, MX21_GPIO6_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-
- pinctrl_provide_dummies();
- imx_add_imx_dma("imx21-dma", MX21_DMA_BASE_ADDR, MX21_INT_DMACH0);
- platform_device_register_simple("imx21-audmux", 0, imx21_audmux_res,
- ARRAY_SIZE(imx21_audmux_res));
-}
diff --git a/arch/arm/mach-imx/mm-imx27.c b/arch/arm/mach-imx/mm-imx27.c
deleted file mode 100644
index 2717614..0000000
--- a/arch/arm/mach-imx/mm-imx27.c
+++ /dev/null
@@ -1,88 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/mach-imx/mm-imx27.c
- *
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/pinctrl/machine.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices/devices-common.h"
-#include "hardware.h"
-#include "iomux-v1.h"
-
-/* MX27 memory map definition */
-static struct map_desc imx27_io_desc[] __initdata = {
- /*
- * this fixed mapping covers:
- * - AIPI1
- * - AIPI2
- * - AITC
- * - ROM Patch
- * - and some reserved space
- */
- imx_map_entry(MX27, AIPI, MT_DEVICE),
- /*
- * this fixed mapping covers:
- * - CSI
- * - ATA
- */
- imx_map_entry(MX27, SAHB1, MT_DEVICE),
- /*
- * this fixed mapping covers:
- * - EMI
- */
- imx_map_entry(MX27, X_MEMC, MT_DEVICE),
-};
-
-/*
- * Initialize the memory map. It is called during the
- * system startup to create static physical to virtual
- * memory map for the IO modules.
- */
-void __init mx27_map_io(void)
-{
- iotable_init(imx27_io_desc, ARRAY_SIZE(imx27_io_desc));
-}
-
-void __init imx27_init_early(void)
-{
- mxc_set_cpu_type(MXC_CPU_MX27);
- imx_iomuxv1_init(MX27_IO_ADDRESS(MX27_GPIO_BASE_ADDR),
- MX27_NUM_GPIO_PORT);
-}
-
-void __init mx27_init_irq(void)
-{
- mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
-}
-
-static const struct resource imx27_audmux_res[] __initconst = {
- DEFINE_RES_MEM(MX27_AUDMUX_BASE_ADDR, SZ_4K),
-};
-
-void __init imx27_soc_init(void)
-{
- mxc_arch_reset_init(MX27_IO_ADDRESS(MX27_WDOG_BASE_ADDR));
- mxc_device_init();
-
- /* i.mx27 has the i.mx21 type gpio */
- mxc_register_gpio("imx21-gpio", 0, MX27_GPIO1_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 1, MX27_GPIO2_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 2, MX27_GPIO3_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 3, MX27_GPIO4_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 4, MX27_GPIO5_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
- mxc_register_gpio("imx21-gpio", 5, MX27_GPIO6_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-
- pinctrl_provide_dummies();
- imx_add_imx_dma("imx27-dma", MX27_DMA_BASE_ADDR, MX27_INT_DMACH0);
- /* imx27 has the imx21 type audmux */
- platform_device_register_simple("imx21-audmux", 0, imx27_audmux_res,
- ARRAY_SIZE(imx27_audmux_res));
-
- imx27_pm_init();
-}
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index ea2d58a..5056438 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -11,6 +11,7 @@
#include <linux/init.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/of_address.h>
#include <linux/pinctrl/machine.h>
#include <asm/system_misc.h>
@@ -19,9 +20,7 @@
#include "common.h"
#include "crmregs-imx3.h"
-#include "devices/devices-common.h"
#include "hardware.h"
-#include "iomux-v3.h"
void __iomem *mx3_ccm_base;
@@ -71,40 +70,6 @@ static void __iomem *imx3_ioremap_caller(phys_addr_t phys_addr, size_t size,
return __arm_ioremap_caller(phys_addr, size, mtype, caller);
}
-static void __init imx3_init_l2x0(void)
-{
-#ifdef CONFIG_CACHE_L2X0
- void __iomem *l2x0_base;
- void __iomem *clkctl_base;
-
-/*
- * First of all, we must repair broken chip settings. There are some
- * i.MX35 CPUs in the wild, comming with bogus L2 cache settings. These
- * misconfigured CPUs will run amok immediately when the L2 cache gets enabled.
- * Workaraound is to setup the correct register setting prior enabling the
- * L2 cache. This should not hurt already working CPUs, as they are using the
- * same value.
- */
-#define L2_MEM_VAL 0x10
-
- clkctl_base = ioremap(MX35_CLKCTL_BASE_ADDR, 4096);
- if (clkctl_base != NULL) {
- writel(0x00000515, clkctl_base + L2_MEM_VAL);
- iounmap(clkctl_base);
- } else {
- pr_err("L2 cache: Cannot fix timing. Trying to continue without\n");
- }
-
- l2x0_base = ioremap(MX3x_L2CC_BASE_ADDR, 4096);
- if (!l2x0_base) {
- printk(KERN_ERR "remapping L2 cache area failed\n");
- return;
- }
-
- l2x0_init(l2x0_base, 0x00030024, 0x00000000);
-#endif
-}
-
#ifdef CONFIG_SOC_IMX31
static struct map_desc mx31_io_desc[] __initdata = {
imx_map_entry(MX31, X_MEMC, MT_DEVICE),
@@ -135,70 +100,26 @@ static void imx31_idle(void)
void __init imx31_init_early(void)
{
+ struct device_node *np;
+
mxc_set_cpu_type(MXC_CPU_MX31);
arch_ioremap_caller = imx3_ioremap_caller;
arm_pm_idle = imx31_idle;
- mx3_ccm_base = MX31_IO_ADDRESS(MX31_CCM_BASE_ADDR);
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx31-ccm");
+ mx3_ccm_base = of_iomap(np, 0);
+ BUG_ON(!mx3_ccm_base);
}
void __init mx31_init_irq(void)
{
- mxc_init_irq(MX31_IO_ADDRESS(MX31_AVIC_BASE_ADDR));
-}
+ void __iomem *avic_base;
+ struct device_node *np;
-static struct sdma_script_start_addrs imx31_to1_sdma_script __initdata = {
- .per_2_per_addr = 1677,
-};
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx31-avic");
+ avic_base = of_iomap(np, 0);
+ BUG_ON(!avic_base);
-static struct sdma_script_start_addrs imx31_to2_sdma_script __initdata = {
- .ap_2_ap_addr = 423,
- .ap_2_bp_addr = 829,
- .bp_2_ap_addr = 1029,
-};
-
-static struct sdma_platform_data imx31_sdma_pdata __initdata = {
- .fw_name = "sdma-imx31-to2.bin",
- .script_addrs = &imx31_to2_sdma_script,
-};
-
-static const struct resource imx31_audmux_res[] __initconst = {
- DEFINE_RES_MEM(MX31_AUDMUX_BASE_ADDR, SZ_16K),
-};
-
-static const struct resource imx31_rnga_res[] __initconst = {
- DEFINE_RES_MEM(MX31_RNGA_BASE_ADDR, SZ_16K),
-};
-
-void __init imx31_soc_init(void)
-{
- int to_version = mx31_revision() >> 4;
-
- imx3_init_l2x0();
-
- mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
- mxc_device_init();
-
- mxc_register_gpio("imx31-gpio", 0, MX31_GPIO1_BASE_ADDR, SZ_16K, MX31_INT_GPIO1, 0);
- mxc_register_gpio("imx31-gpio", 1, MX31_GPIO2_BASE_ADDR, SZ_16K, MX31_INT_GPIO2, 0);
- mxc_register_gpio("imx31-gpio", 2, MX31_GPIO3_BASE_ADDR, SZ_16K, MX31_INT_GPIO3, 0);
-
- pinctrl_provide_dummies();
-
- if (to_version == 1) {
- strncpy(imx31_sdma_pdata.fw_name, "sdma-imx31-to1.bin",
- strlen(imx31_sdma_pdata.fw_name));
- imx31_sdma_pdata.script_addrs = &imx31_to1_sdma_script;
- }
-
- imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata);
-
- imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS1_BASE_ADDR));
- imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS2_BASE_ADDR));
-
- platform_device_register_simple("imx31-audmux", 0, imx31_audmux_res,
- ARRAY_SIZE(imx31_audmux_res));
- platform_device_register_simple("mxc_rnga", -1, imx31_rnga_res,
- ARRAY_SIZE(imx31_rnga_res));
+ mxc_init_irq(avic_base);
}
#endif /* ifdef CONFIG_SOC_IMX31 */
@@ -228,85 +149,25 @@ static void imx35_idle(void)
void __init imx35_init_early(void)
{
+ struct device_node *np;
+
mxc_set_cpu_type(MXC_CPU_MX35);
- mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
arm_pm_idle = imx35_idle;
arch_ioremap_caller = imx3_ioremap_caller;
- mx3_ccm_base = MX35_IO_ADDRESS(MX35_CCM_BASE_ADDR);
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx35-ccm");
+ mx3_ccm_base = of_iomap(np, 0);
+ BUG_ON(!mx3_ccm_base);
}
void __init mx35_init_irq(void)
{
- mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR));
-}
+ void __iomem *avic_base;
+ struct device_node *np;
-static struct sdma_script_start_addrs imx35_to1_sdma_script __initdata = {
- .ap_2_ap_addr = 642,
- .uart_2_mcu_addr = 817,
- .mcu_2_app_addr = 747,
- .uartsh_2_mcu_addr = 1183,
- .per_2_shp_addr = 1033,
- .mcu_2_shp_addr = 961,
- .ata_2_mcu_addr = 1333,
- .mcu_2_ata_addr = 1252,
- .app_2_mcu_addr = 683,
- .shp_2_per_addr = 1111,
- .shp_2_mcu_addr = 892,
-};
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx35-avic");
+ avic_base = of_iomap(np, 0);
+ BUG_ON(!avic_base);
-static struct sdma_script_start_addrs imx35_to2_sdma_script __initdata = {
- .ap_2_ap_addr = 729,
- .uart_2_mcu_addr = 904,
- .per_2_app_addr = 1597,
- .mcu_2_app_addr = 834,
- .uartsh_2_mcu_addr = 1270,
- .per_2_shp_addr = 1120,
- .mcu_2_shp_addr = 1048,
- .ata_2_mcu_addr = 1429,
- .mcu_2_ata_addr = 1339,
- .app_2_per_addr = 1531,
- .app_2_mcu_addr = 770,
- .shp_2_per_addr = 1198,
- .shp_2_mcu_addr = 979,
-};
-
-static struct sdma_platform_data imx35_sdma_pdata __initdata = {
- .fw_name = "sdma-imx35-to2.bin",
- .script_addrs = &imx35_to2_sdma_script,
-};
-
-static const struct resource imx35_audmux_res[] __initconst = {
- DEFINE_RES_MEM(MX35_AUDMUX_BASE_ADDR, SZ_16K),
-};
-
-void __init imx35_soc_init(void)
-{
- int to_version = mx35_revision() >> 4;
-
- imx3_init_l2x0();
-
- mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
- mxc_device_init();
-
- mxc_register_gpio("imx35-gpio", 0, MX35_GPIO1_BASE_ADDR, SZ_16K, MX35_INT_GPIO1, 0);
- mxc_register_gpio("imx35-gpio", 1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
- mxc_register_gpio("imx35-gpio", 2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
-
- pinctrl_provide_dummies();
- if (to_version == 1) {
- strncpy(imx35_sdma_pdata.fw_name, "sdma-imx35-to1.bin",
- strlen(imx35_sdma_pdata.fw_name));
- imx35_sdma_pdata.script_addrs = &imx35_to1_sdma_script;
- }
-
- imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata);
-
- /* Setup AIPS registers */
- imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS1_BASE_ADDR));
- imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS2_BASE_ADDR));
-
- /* i.mx35 has the i.mx31 type audmux */
- platform_device_register_simple("imx31-audmux", 0, imx35_audmux_res,
- ARRAY_SIZE(imx35_audmux_res));
+ mxc_init_irq(avic_base);
}
#endif /* ifdef CONFIG_SOC_IMX35 */
diff --git a/arch/arm/mach-imx/mx21.h b/arch/arm/mach-imx/mx21.h
deleted file mode 100644
index 38be12a..0000000
--- a/arch/arm/mach-imx/mx21.h
+++ /dev/null
@@ -1,176 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
- * Copyright 2009 Holger Schurig, hs4233@mail.mn-solutions.de
- *
- * This contains i.MX21-specific hardware definitions. For those
- * hardware pieces that are common between i.MX21 and i.MX27, have a
- * look at mx2x.h.
- */
-
-#ifndef __MACH_MX21_H__
-#define __MACH_MX21_H__
-
-#define MX21_AIPI_BASE_ADDR 0x10000000
-#define MX21_AIPI_SIZE SZ_1M
-#define MX21_DMA_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x01000)
-#define MX21_WDOG_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x02000)
-#define MX21_GPT1_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x03000)
-#define MX21_GPT2_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x04000)
-#define MX21_GPT3_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x05000)
-#define MX21_PWM_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x06000)
-#define MX21_RTC_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x07000)
-#define MX21_KPP_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x08000)
-#define MX21_OWIRE_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x09000)
-#define MX21_UART1_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0a000)
-#define MX21_UART2_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0b000)
-#define MX21_UART3_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0c000)
-#define MX21_UART4_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0d000)
-#define MX21_CSPI1_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0e000)
-#define MX21_CSPI2_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x0f000)
-#define MX21_SSI1_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x10000)
-#define MX21_SSI2_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x11000)
-#define MX21_I2C_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x12000)
-#define MX21_SDHC1_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x13000)
-#define MX21_SDHC2_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x14000)
-#define MX21_GPIO_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x15000)
-#define MX21_GPIO1_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x000)
-#define MX21_GPIO2_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x100)
-#define MX21_GPIO3_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x200)
-#define MX21_GPIO4_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x300)
-#define MX21_GPIO5_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x400)
-#define MX21_GPIO6_BASE_ADDR (MX21_GPIO_BASE_ADDR + 0x500)
-#define MX21_AUDMUX_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x16000)
-#define MX21_CSPI3_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x17000)
-#define MX21_LCDC_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x21000)
-#define MX21_SLCDC_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x22000)
-#define MX21_USBOTG_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x24000)
-#define MX21_EMMA_PP_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x26000)
-#define MX21_EMMA_PRP_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x26400)
-#define MX21_CCM_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x27000)
-#define MX21_SYSCTRL_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x27800)
-#define MX21_JAM_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x3e000)
-#define MX21_MAX_BASE_ADDR (MX21_AIPI_BASE_ADDR + 0x3f000)
-
-#define MX21_AVIC_BASE_ADDR 0x10040000
-
-#define MX21_SAHB1_BASE_ADDR 0x80000000
-#define MX21_SAHB1_SIZE SZ_1M
-#define MX21_CSI_BASE_ADDR (MX2x_SAHB1_BASE_ADDR + 0x0000)
-
-/* Memory regions and CS */
-#define MX21_SDRAM_BASE_ADDR 0xc0000000
-#define MX21_CSD1_BASE_ADDR 0xc4000000
-
-#define MX21_CS0_BASE_ADDR 0xc8000000
-#define MX21_CS1_BASE_ADDR 0xcc000000
-#define MX21_CS2_BASE_ADDR 0xd0000000
-#define MX21_CS3_BASE_ADDR 0xd1000000
-#define MX21_CS4_BASE_ADDR 0xd2000000
-#define MX21_PCMCIA_MEM_BASE_ADDR 0xd4000000
-#define MX21_CS5_BASE_ADDR 0xdd000000
-
-/* NAND, SDRAM, WEIM etc controllers */
-#define MX21_X_MEMC_BASE_ADDR 0xdf000000
-#define MX21_X_MEMC_SIZE SZ_256K
-
-#define MX21_SDRAMC_BASE_ADDR (MX21_X_MEMC_BASE_ADDR + 0x0000)
-#define MX21_EIM_BASE_ADDR (MX21_X_MEMC_BASE_ADDR + 0x1000)
-#define MX21_PCMCIA_CTL_BASE_ADDR (MX21_X_MEMC_BASE_ADDR + 0x2000)
-#define MX21_NFC_BASE_ADDR (MX21_X_MEMC_BASE_ADDR + 0x3000)
-
-#define MX21_IRAM_BASE_ADDR 0xffffe800 /* internal ram */
-
-#define MX21_IO_P2V(x) IMX_IO_P2V(x)
-#define MX21_IO_ADDRESS(x) IOMEM(MX21_IO_P2V(x))
-
-/* fixed interrupt numbers */
-#include <asm/irq.h>
-#define MX21_INT_CSPI3 (NR_IRQS_LEGACY + 6)
-#define MX21_INT_GPIO (NR_IRQS_LEGACY + 8)
-#define MX21_INT_FIRI (NR_IRQS_LEGACY + 9)
-#define MX21_INT_SDHC2 (NR_IRQS_LEGACY + 10)
-#define MX21_INT_SDHC1 (NR_IRQS_LEGACY + 11)
-#define MX21_INT_I2C (NR_IRQS_LEGACY + 12)
-#define MX21_INT_SSI2 (NR_IRQS_LEGACY + 13)
-#define MX21_INT_SSI1 (NR_IRQS_LEGACY + 14)
-#define MX21_INT_CSPI2 (NR_IRQS_LEGACY + 15)
-#define MX21_INT_CSPI1 (NR_IRQS_LEGACY + 16)
-#define MX21_INT_UART4 (NR_IRQS_LEGACY + 17)
-#define MX21_INT_UART3 (NR_IRQS_LEGACY + 18)
-#define MX21_INT_UART2 (NR_IRQS_LEGACY + 19)
-#define MX21_INT_UART1 (NR_IRQS_LEGACY + 20)
-#define MX21_INT_KPP (NR_IRQS_LEGACY + 21)
-#define MX21_INT_RTC (NR_IRQS_LEGACY + 22)
-#define MX21_INT_PWM (NR_IRQS_LEGACY + 23)
-#define MX21_INT_GPT3 (NR_IRQS_LEGACY + 24)
-#define MX21_INT_GPT2 (NR_IRQS_LEGACY + 25)
-#define MX21_INT_GPT1 (NR_IRQS_LEGACY + 26)
-#define MX21_INT_WDOG (NR_IRQS_LEGACY + 27)
-#define MX21_INT_PCMCIA (NR_IRQS_LEGACY + 28)
-#define MX21_INT_NFC (NR_IRQS_LEGACY + 29)
-#define MX21_INT_BMI (NR_IRQS_LEGACY + 30)
-#define MX21_INT_CSI (NR_IRQS_LEGACY + 31)
-#define MX21_INT_DMACH0 (NR_IRQS_LEGACY + 32)
-#define MX21_INT_DMACH1 (NR_IRQS_LEGACY + 33)
-#define MX21_INT_DMACH2 (NR_IRQS_LEGACY + 34)
-#define MX21_INT_DMACH3 (NR_IRQS_LEGACY + 35)
-#define MX21_INT_DMACH4 (NR_IRQS_LEGACY + 36)
-#define MX21_INT_DMACH5 (NR_IRQS_LEGACY + 37)
-#define MX21_INT_DMACH6 (NR_IRQS_LEGACY + 38)
-#define MX21_INT_DMACH7 (NR_IRQS_LEGACY + 39)
-#define MX21_INT_DMACH8 (NR_IRQS_LEGACY + 40)
-#define MX21_INT_DMACH9 (NR_IRQS_LEGACY + 41)
-#define MX21_INT_DMACH10 (NR_IRQS_LEGACY + 42)
-#define MX21_INT_DMACH11 (NR_IRQS_LEGACY + 43)
-#define MX21_INT_DMACH12 (NR_IRQS_LEGACY + 44)
-#define MX21_INT_DMACH13 (NR_IRQS_LEGACY + 45)
-#define MX21_INT_DMACH14 (NR_IRQS_LEGACY + 46)
-#define MX21_INT_DMACH15 (NR_IRQS_LEGACY + 47)
-#define MX21_INT_EMMAENC (NR_IRQS_LEGACY + 49)
-#define MX21_INT_EMMADEC (NR_IRQS_LEGACY + 50)
-#define MX21_INT_EMMAPRP (NR_IRQS_LEGACY + 51)
-#define MX21_INT_EMMAPP (NR_IRQS_LEGACY + 52)
-#define MX21_INT_USBWKUP (NR_IRQS_LEGACY + 53)
-#define MX21_INT_USBDMA (NR_IRQS_LEGACY + 54)
-#define MX21_INT_USBHOST (NR_IRQS_LEGACY + 55)
-#define MX21_INT_USBFUNC (NR_IRQS_LEGACY + 56)
-#define MX21_INT_USBMNP (NR_IRQS_LEGACY + 57)
-#define MX21_INT_USBCTRL (NR_IRQS_LEGACY + 58)
-#define MX21_INT_SLCDC (NR_IRQS_LEGACY + 60)
-#define MX21_INT_LCDC (NR_IRQS_LEGACY + 61)
-
-/* fixed DMA request numbers */
-#define MX21_DMA_REQ_CSPI3_RX 1
-#define MX21_DMA_REQ_CSPI3_TX 2
-#define MX21_DMA_REQ_EXT 3
-#define MX21_DMA_REQ_FIRI_RX 4
-#define MX21_DMA_REQ_SDHC2 6
-#define MX21_DMA_REQ_SDHC1 7
-#define MX21_DMA_REQ_SSI2_RX0 8
-#define MX21_DMA_REQ_SSI2_TX0 9
-#define MX21_DMA_REQ_SSI2_RX1 10
-#define MX21_DMA_REQ_SSI2_TX1 11
-#define MX21_DMA_REQ_SSI1_RX0 12
-#define MX21_DMA_REQ_SSI1_TX0 13
-#define MX21_DMA_REQ_SSI1_RX1 14
-#define MX21_DMA_REQ_SSI1_TX1 15
-#define MX21_DMA_REQ_CSPI2_RX 16
-#define MX21_DMA_REQ_CSPI2_TX 17
-#define MX21_DMA_REQ_CSPI1_RX 18
-#define MX21_DMA_REQ_CSPI1_TX 19
-#define MX21_DMA_REQ_UART4_RX 20
-#define MX21_DMA_REQ_UART4_TX 21
-#define MX21_DMA_REQ_UART3_RX 22
-#define MX21_DMA_REQ_UART3_TX 23
-#define MX21_DMA_REQ_UART2_RX 24
-#define MX21_DMA_REQ_UART2_TX 25
-#define MX21_DMA_REQ_UART1_RX 26
-#define MX21_DMA_REQ_UART1_TX 27
-#define MX21_DMA_REQ_BMI_TX 28
-#define MX21_DMA_REQ_BMI_RX 29
-#define MX21_DMA_REQ_CSI_STAT 30
-#define MX21_DMA_REQ_CSI_RX 31
-
-#endif /* ifndef __MACH_MX21_H__ */
diff --git a/arch/arm/mach-imx/mx27.h b/arch/arm/mach-imx/mx27.h
index c6f7aae..241c04d 100644
--- a/arch/arm/mach-imx/mx27.h
+++ b/arch/arm/mach-imx/mx27.h
@@ -13,209 +13,13 @@
#define MX27_AIPI_BASE_ADDR 0x10000000
#define MX27_AIPI_SIZE SZ_1M
-#define MX27_DMA_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x01000)
-#define MX27_WDOG_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x02000)
-#define MX27_GPT1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x03000)
-#define MX27_GPT2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x04000)
-#define MX27_GPT3_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x05000)
-#define MX27_PWM_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x06000)
-#define MX27_RTC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x07000)
-#define MX27_KPP_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x08000)
-#define MX27_OWIRE_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x09000)
-#define MX27_UART1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0a000)
-#define MX27_UART2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0b000)
-#define MX27_UART3_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0c000)
-#define MX27_UART4_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0d000)
-#define MX27_CSPI1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0e000)
-#define MX27_CSPI2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x0f000)
-#define MX27_SSI1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x10000)
-#define MX27_SSI2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x11000)
-#define MX27_I2C1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x12000)
-#define MX27_SDHC1_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x13000)
-#define MX27_SDHC2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x14000)
-#define MX27_GPIO_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x15000)
-#define MX27_GPIO1_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x000)
-#define MX27_GPIO2_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x100)
-#define MX27_GPIO3_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x200)
-#define MX27_GPIO4_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x300)
-#define MX27_GPIO5_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x400)
-#define MX27_GPIO6_BASE_ADDR (MX27_GPIO_BASE_ADDR + 0x500)
-#define MX27_AUDMUX_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x16000)
-#define MX27_CSPI3_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x17000)
-#define MX27_MSHC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x18000)
-#define MX27_GPT4_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x19000)
-#define MX27_GPT5_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1a000)
-#define MX27_UART5_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1b000)
-#define MX27_UART6_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1c000)
-#define MX27_I2C2_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1d000)
-#define MX27_SDHC3_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1e000)
-#define MX27_GPT6_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x1f000)
-#define MX27_LCDC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x21000)
-#define MX27_SLCDC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x22000)
-#define MX27_VPU_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x23000)
-#define MX27_USB_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x24000)
-#define MX27_USB_OTG_BASE_ADDR (MX27_USB_BASE_ADDR + 0x0000)
-#define MX27_USB_HS1_BASE_ADDR (MX27_USB_BASE_ADDR + 0x0200)
-#define MX27_USB_HS2_BASE_ADDR (MX27_USB_BASE_ADDR + 0x0400)
-#define MX27_SAHARA_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x25000)
-#define MX27_EMMAPP_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x26000)
-#define MX27_EMMAPRP_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x26400)
-#define MX27_CCM_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x27000)
-#define MX27_SYSCTRL_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x27800)
-#define MX27_IIM_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x28000)
-#define MX27_RTIC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x2a000)
-#define MX27_FEC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x2b000)
-#define MX27_SCC_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x2c000)
-#define MX27_ETB_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x3b000)
-#define MX27_ETB_RAM_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x3c000)
-#define MX27_JAM_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x3e000)
-#define MX27_MAX_BASE_ADDR (MX27_AIPI_BASE_ADDR + 0x3f000)
-
-#define MX27_AVIC_BASE_ADDR 0x10040000
-
-/* ROM patch */
-#define MX27_ROMP_BASE_ADDR 0x10041000
#define MX27_SAHB1_BASE_ADDR 0x80000000
#define MX27_SAHB1_SIZE SZ_1M
-#define MX27_CSI_BASE_ADDR (MX27_SAHB1_BASE_ADDR + 0x0000)
-#define MX27_ATA_BASE_ADDR (MX27_SAHB1_BASE_ADDR + 0x1000)
-/* Memory regions and CS */
-#define MX27_SDRAM_BASE_ADDR 0xa0000000
-#define MX27_CSD1_BASE_ADDR 0xb0000000
-
-#define MX27_CS0_BASE_ADDR 0xc0000000
-#define MX27_CS1_BASE_ADDR 0xc8000000
-#define MX27_CS2_BASE_ADDR 0xd0000000
-#define MX27_CS3_BASE_ADDR 0xd2000000
-#define MX27_CS4_BASE_ADDR 0xd4000000
-#define MX27_CS5_BASE_ADDR 0xd6000000
-
-/* NAND, SDRAM, WEIM, M3IF, EMI controllers */
#define MX27_X_MEMC_BASE_ADDR 0xd8000000
#define MX27_X_MEMC_SIZE SZ_1M
-#define MX27_NFC_BASE_ADDR (MX27_X_MEMC_BASE_ADDR)
-#define MX27_SDRAMC_BASE_ADDR (MX27_X_MEMC_BASE_ADDR + 0x1000)
-#define MX27_WEIM_BASE_ADDR (MX27_X_MEMC_BASE_ADDR + 0x2000)
-#define MX27_M3IF_BASE_ADDR (MX27_X_MEMC_BASE_ADDR + 0x3000)
-#define MX27_PCMCIA_CTL_BASE_ADDR (MX27_X_MEMC_BASE_ADDR + 0x4000)
-
-#define MX27_WEIM_CSCRx_BASE_ADDR(cs) (MX27_WEIM_BASE_ADDR + (cs) * 0x10)
-#define MX27_WEIM_CSCRxU(cs) (MX27_WEIM_CSCRx_BASE_ADDR(cs))
-#define MX27_WEIM_CSCRxL(cs) (MX27_WEIM_CSCRx_BASE_ADDR(cs) + 0x4)
-#define MX27_WEIM_CSCRxA(cs) (MX27_WEIM_CSCRx_BASE_ADDR(cs) + 0x8)
-
-#define MX27_PCMCIA_MEM_BASE_ADDR 0xdc000000
-
-/* IRAM */
-#define MX27_IRAM_BASE_ADDR 0xffff4c00 /* internal ram */
#define MX27_IO_P2V(x) IMX_IO_P2V(x)
-#define MX27_IO_ADDRESS(x) IOMEM(MX27_IO_P2V(x))
-
-/* fixed interrupt numbers */
-#include <asm/irq.h>
-#define MX27_INT_I2C2 (NR_IRQS_LEGACY + 1)
-#define MX27_INT_GPT6 (NR_IRQS_LEGACY + 2)
-#define MX27_INT_GPT5 (NR_IRQS_LEGACY + 3)
-#define MX27_INT_GPT4 (NR_IRQS_LEGACY + 4)
-#define MX27_INT_RTIC (NR_IRQS_LEGACY + 5)
-#define MX27_INT_CSPI3 (NR_IRQS_LEGACY + 6)
-#define MX27_INT_MSHC (NR_IRQS_LEGACY + 7)
-#define MX27_INT_GPIO (NR_IRQS_LEGACY + 8)
-#define MX27_INT_SDHC3 (NR_IRQS_LEGACY + 9)
-#define MX27_INT_SDHC2 (NR_IRQS_LEGACY + 10)
-#define MX27_INT_SDHC1 (NR_IRQS_LEGACY + 11)
-#define MX27_INT_I2C1 (NR_IRQS_LEGACY + 12)
-#define MX27_INT_SSI2 (NR_IRQS_LEGACY + 13)
-#define MX27_INT_SSI1 (NR_IRQS_LEGACY + 14)
-#define MX27_INT_CSPI2 (NR_IRQS_LEGACY + 15)
-#define MX27_INT_CSPI1 (NR_IRQS_LEGACY + 16)
-#define MX27_INT_UART4 (NR_IRQS_LEGACY + 17)
-#define MX27_INT_UART3 (NR_IRQS_LEGACY + 18)
-#define MX27_INT_UART2 (NR_IRQS_LEGACY + 19)
-#define MX27_INT_UART1 (NR_IRQS_LEGACY + 20)
-#define MX27_INT_KPP (NR_IRQS_LEGACY + 21)
-#define MX27_INT_RTC (NR_IRQS_LEGACY + 22)
-#define MX27_INT_PWM (NR_IRQS_LEGACY + 23)
-#define MX27_INT_GPT3 (NR_IRQS_LEGACY + 24)
-#define MX27_INT_GPT2 (NR_IRQS_LEGACY + 25)
-#define MX27_INT_GPT1 (NR_IRQS_LEGACY + 26)
-#define MX27_INT_WDOG (NR_IRQS_LEGACY + 27)
-#define MX27_INT_PCMCIA (NR_IRQS_LEGACY + 28)
-#define MX27_INT_NFC (NR_IRQS_LEGACY + 29)
-#define MX27_INT_ATA (NR_IRQS_LEGACY + 30)
-#define MX27_INT_CSI (NR_IRQS_LEGACY + 31)
-#define MX27_INT_DMACH0 (NR_IRQS_LEGACY + 32)
-#define MX27_INT_DMACH1 (NR_IRQS_LEGACY + 33)
-#define MX27_INT_DMACH2 (NR_IRQS_LEGACY + 34)
-#define MX27_INT_DMACH3 (NR_IRQS_LEGACY + 35)
-#define MX27_INT_DMACH4 (NR_IRQS_LEGACY + 36)
-#define MX27_INT_DMACH5 (NR_IRQS_LEGACY + 37)
-#define MX27_INT_DMACH6 (NR_IRQS_LEGACY + 38)
-#define MX27_INT_DMACH7 (NR_IRQS_LEGACY + 39)
-#define MX27_INT_DMACH8 (NR_IRQS_LEGACY + 40)
-#define MX27_INT_DMACH9 (NR_IRQS_LEGACY + 41)
-#define MX27_INT_DMACH10 (NR_IRQS_LEGACY + 42)
-#define MX27_INT_DMACH11 (NR_IRQS_LEGACY + 43)
-#define MX27_INT_DMACH12 (NR_IRQS_LEGACY + 44)
-#define MX27_INT_DMACH13 (NR_IRQS_LEGACY + 45)
-#define MX27_INT_DMACH14 (NR_IRQS_LEGACY + 46)
-#define MX27_INT_DMACH15 (NR_IRQS_LEGACY + 47)
-#define MX27_INT_UART6 (NR_IRQS_LEGACY + 48)
-#define MX27_INT_UART5 (NR_IRQS_LEGACY + 49)
-#define MX27_INT_FEC (NR_IRQS_LEGACY + 50)
-#define MX27_INT_EMMAPRP (NR_IRQS_LEGACY + 51)
-#define MX27_INT_EMMAPP (NR_IRQS_LEGACY + 52)
-#define MX27_INT_VPU (NR_IRQS_LEGACY + 53)
-#define MX27_INT_USB_HS1 (NR_IRQS_LEGACY + 54)
-#define MX27_INT_USB_HS2 (NR_IRQS_LEGACY + 55)
-#define MX27_INT_USB_OTG (NR_IRQS_LEGACY + 56)
-#define MX27_INT_SCC_SMN (NR_IRQS_LEGACY + 57)
-#define MX27_INT_SCC_SCM (NR_IRQS_LEGACY + 58)
-#define MX27_INT_SAHARA (NR_IRQS_LEGACY + 59)
-#define MX27_INT_SLCDC (NR_IRQS_LEGACY + 60)
-#define MX27_INT_LCDC (NR_IRQS_LEGACY + 61)
-#define MX27_INT_IIM (NR_IRQS_LEGACY + 62)
-#define MX27_INT_CCM (NR_IRQS_LEGACY + 63)
-
-/* fixed DMA request numbers */
-#define MX27_DMA_REQ_CSPI3_RX 1
-#define MX27_DMA_REQ_CSPI3_TX 2
-#define MX27_DMA_REQ_EXT 3
-#define MX27_DMA_REQ_MSHC 4
-#define MX27_DMA_REQ_SDHC2 6
-#define MX27_DMA_REQ_SDHC1 7
-#define MX27_DMA_REQ_SSI2_RX0 8
-#define MX27_DMA_REQ_SSI2_TX0 9
-#define MX27_DMA_REQ_SSI2_RX1 10
-#define MX27_DMA_REQ_SSI2_TX1 11
-#define MX27_DMA_REQ_SSI1_RX0 12
-#define MX27_DMA_REQ_SSI1_TX0 13
-#define MX27_DMA_REQ_SSI1_RX1 14
-#define MX27_DMA_REQ_SSI1_TX1 15
-#define MX27_DMA_REQ_CSPI2_RX 16
-#define MX27_DMA_REQ_CSPI2_TX 17
-#define MX27_DMA_REQ_CSPI1_RX 18
-#define MX27_DMA_REQ_CSPI1_TX 19
-#define MX27_DMA_REQ_UART4_RX 20
-#define MX27_DMA_REQ_UART4_TX 21
-#define MX27_DMA_REQ_UART3_RX 22
-#define MX27_DMA_REQ_UART3_TX 23
-#define MX27_DMA_REQ_UART2_RX 24
-#define MX27_DMA_REQ_UART2_TX 25
-#define MX27_DMA_REQ_UART1_RX 26
-#define MX27_DMA_REQ_UART1_TX 27
-#define MX27_DMA_REQ_ATA_TX 28
-#define MX27_DMA_REQ_ATA_RCV 29
-#define MX27_DMA_REQ_CSI_STAT 30
-#define MX27_DMA_REQ_CSI_RX 31
-#define MX27_DMA_REQ_UART5_TX 32
-#define MX27_DMA_REQ_UART5_RX 33
-#define MX27_DMA_REQ_UART6_TX 34
-#define MX27_DMA_REQ_UART6_RX 35
-#define MX27_DMA_REQ_SDHC3 36
-#define MX27_DMA_REQ_NFC 37
#endif /* ifndef __MACH_MX27_H__ */
diff --git a/arch/arm/mach-imx/mx31.h b/arch/arm/mach-imx/mx31.h
index d957467..08a72e2 100644
--- a/arch/arm/mach-imx/mx31.h
+++ b/arch/arm/mach-imx/mx31.h
@@ -2,196 +2,17 @@
#ifndef __MACH_MX31_H__
#define __MACH_MX31_H__
-/*
- * IRAM
- */
-#define MX31_IRAM_BASE_ADDR 0x1ffc0000 /* internal ram */
-#define MX31_IRAM_SIZE SZ_16K
-
-#define MX31_L2CC_BASE_ADDR 0x30000000
-#define MX31_L2CC_SIZE SZ_1M
-
#define MX31_AIPS1_BASE_ADDR 0x43f00000
#define MX31_AIPS1_SIZE SZ_1M
-#define MX31_MAX_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x04000)
-#define MX31_EVTMON_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x08000)
-#define MX31_CLKCTL_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x0c000)
-#define MX31_ETB_SLOT4_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x10000)
-#define MX31_ETB_SLOT5_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x14000)
-#define MX31_ECT_CTIO_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x18000)
-#define MX31_I2C1_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x80000)
-#define MX31_I2C3_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x84000)
-#define MX31_USB_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x88000)
-#define MX31_USB_OTG_BASE_ADDR (MX31_USB_BASE_ADDR + 0x0000)
-#define MX31_USB_HS1_BASE_ADDR (MX31_USB_BASE_ADDR + 0x0200)
-#define MX31_USB_HS2_BASE_ADDR (MX31_USB_BASE_ADDR + 0x0400)
-#define MX31_ATA_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x8c000)
-#define MX31_UART1_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x90000)
-#define MX31_UART2_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x94000)
-#define MX31_I2C2_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x98000)
-#define MX31_OWIRE_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x9c000)
-#define MX31_SSI1_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xa0000)
-#define MX31_CSPI1_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xa4000)
-#define MX31_KPP_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xa8000)
-#define MX31_IOMUXC_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xac000)
-#define MX31_UART4_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xb0000)
-#define MX31_UART5_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xb4000)
-#define MX31_ECT_IP1_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xb8000)
-#define MX31_ECT_IP2_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0xbc000)
-
#define MX31_SPBA0_BASE_ADDR 0x50000000
#define MX31_SPBA0_SIZE SZ_1M
-#define MX31_SDHC1_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x04000)
-#define MX31_SDHC2_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x08000)
-#define MX31_UART3_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x0c000)
-#define MX31_CSPI2_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x10000)
-#define MX31_SSI2_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x14000)
-#define MX31_SIM1_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x18000)
-#define MX31_IIM_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x1c000)
-#define MX31_ATA_DMA_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x20000)
-#define MX31_MSHC1_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x24000)
-#define MX31_SPBA_CTRL_BASE_ADDR (MX31_SPBA0_BASE_ADDR + 0x3c000)
-
#define MX31_AIPS2_BASE_ADDR 0x53f00000
#define MX31_AIPS2_SIZE SZ_1M
-#define MX31_CCM_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x80000)
-#define MX31_CSPI3_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x84000)
-#define MX31_FIRI_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x8c000)
-#define MX31_GPT1_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x90000)
-#define MX31_EPIT1_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x94000)
-#define MX31_EPIT2_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0x98000)
-#define MX31_GPIO3_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xa4000)
-#define MX31_SCC_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xac000)
-#define MX31_SCM_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xae000)
-#define MX31_SMN_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xaf000)
-#define MX31_RNGA_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xb0000)
-#define MX31_IPU_CTRL_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xc0000)
-#define MX31_AUDMUX_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xc4000)
-#define MX31_MPEG4_ENC_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xc8000)
-#define MX31_GPIO1_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xcc000)
-#define MX31_GPIO2_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xd0000)
-#define MX31_SDMA_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xd4000)
-#define MX31_RTC_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xd8000)
-#define MX31_WDOG_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xdc000)
-#define MX31_PWM_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xe0000)
-#define MX31_RTIC_BASE_ADDR (MX31_AIPS2_BASE_ADDR + 0xec000)
-
-#define MX31_ROMP_BASE_ADDR 0x60000000
-#define MX31_ROMP_BASE_ADDR_VIRT IOMEM(0xfc500000)
-#define MX31_ROMP_SIZE SZ_1M
-
#define MX31_AVIC_BASE_ADDR 0x68000000
#define MX31_AVIC_SIZE SZ_1M
-
-#define MX31_IPU_MEM_BASE_ADDR 0x70000000
-#define MX31_CSD0_BASE_ADDR 0x80000000
-#define MX31_CSD1_BASE_ADDR 0x90000000
-
-#define MX31_CS0_BASE_ADDR 0xa0000000
-#define MX31_CS1_BASE_ADDR 0xa8000000
-#define MX31_CS2_BASE_ADDR 0xb0000000
-#define MX31_CS3_BASE_ADDR 0xb2000000
-
-#define MX31_CS4_BASE_ADDR 0xb4000000
-#define MX31_CS4_BASE_ADDR_VIRT IOMEM(0xf6000000)
-#define MX31_CS4_SIZE SZ_32M
-
-#define MX31_CS5_BASE_ADDR 0xb6000000
-#define MX31_CS5_BASE_ADDR_VIRT IOMEM(0xf8000000)
-#define MX31_CS5_SIZE SZ_32M
-
#define MX31_X_MEMC_BASE_ADDR 0xb8000000
#define MX31_X_MEMC_SIZE SZ_64K
-#define MX31_NFC_BASE_ADDR (MX31_X_MEMC_BASE_ADDR + 0x0000)
-#define MX31_ESDCTL_BASE_ADDR (MX31_X_MEMC_BASE_ADDR + 0x1000)
-#define MX31_WEIM_BASE_ADDR (MX31_X_MEMC_BASE_ADDR + 0x2000)
-#define MX31_M3IF_BASE_ADDR (MX31_X_MEMC_BASE_ADDR + 0x3000)
-#define MX31_EMI_CTL_BASE_ADDR (MX31_X_MEMC_BASE_ADDR + 0x4000)
-#define MX31_PCMCIA_CTL_BASE_ADDR MX31_EMI_CTL_BASE_ADDR
-
-#define MX31_WEIM_CSCRx_BASE_ADDR(cs) (MX31_WEIM_BASE_ADDR + (cs) * 0x10)
-#define MX31_WEIM_CSCRxU(cs) (MX31_WEIM_CSCRx_BASE_ADDR(cs))
-#define MX31_WEIM_CSCRxL(cs) (MX31_WEIM_CSCRx_BASE_ADDR(cs) + 0x4)
-#define MX31_WEIM_CSCRxA(cs) (MX31_WEIM_CSCRx_BASE_ADDR(cs) + 0x8)
-
-#define MX31_PCMCIA_MEM_BASE_ADDR 0xbc000000
#define MX31_IO_P2V(x) IMX_IO_P2V(x)
-#define MX31_IO_ADDRESS(x) IOMEM(MX31_IO_P2V(x))
-
-/*
- * Interrupt numbers
- */
-#include <asm/irq.h>
-#define MX31_INT_I2C3 (NR_IRQS_LEGACY + 3)
-#define MX31_INT_I2C2 (NR_IRQS_LEGACY + 4)
-#define MX31_INT_MPEG4_ENCODER (NR_IRQS_LEGACY + 5)
-#define MX31_INT_RTIC (NR_IRQS_LEGACY + 6)
-#define MX31_INT_FIRI (NR_IRQS_LEGACY + 7)
-#define MX31_INT_SDHC2 (NR_IRQS_LEGACY + 8)
-#define MX31_INT_SDHC1 (NR_IRQS_LEGACY + 9)
-#define MX31_INT_I2C1 (NR_IRQS_LEGACY + 10)
-#define MX31_INT_SSI2 (NR_IRQS_LEGACY + 11)
-#define MX31_INT_SSI1 (NR_IRQS_LEGACY + 12)
-#define MX31_INT_CSPI2 (NR_IRQS_LEGACY + 13)
-#define MX31_INT_CSPI1 (NR_IRQS_LEGACY + 14)
-#define MX31_INT_ATA (NR_IRQS_LEGACY + 15)
-#define MX31_INT_MBX (NR_IRQS_LEGACY + 16)
-#define MX31_INT_CSPI3 (NR_IRQS_LEGACY + 17)
-#define MX31_INT_UART3 (NR_IRQS_LEGACY + 18)
-#define MX31_INT_IIM (NR_IRQS_LEGACY + 19)
-#define MX31_INT_SIM2 (NR_IRQS_LEGACY + 20)
-#define MX31_INT_SIM1 (NR_IRQS_LEGACY + 21)
-#define MX31_INT_RNGA (NR_IRQS_LEGACY + 22)
-#define MX31_INT_EVTMON (NR_IRQS_LEGACY + 23)
-#define MX31_INT_KPP (NR_IRQS_LEGACY + 24)
-#define MX31_INT_RTC (NR_IRQS_LEGACY + 25)
-#define MX31_INT_PWM (NR_IRQS_LEGACY + 26)
-#define MX31_INT_EPIT2 (NR_IRQS_LEGACY + 27)
-#define MX31_INT_EPIT1 (NR_IRQS_LEGACY + 28)
-#define MX31_INT_GPT (NR_IRQS_LEGACY + 29)
-#define MX31_INT_POWER_FAIL (NR_IRQS_LEGACY + 30)
-#define MX31_INT_CCM_DVFS (NR_IRQS_LEGACY + 31)
-#define MX31_INT_UART2 (NR_IRQS_LEGACY + 32)
-#define MX31_INT_NFC (NR_IRQS_LEGACY + 33)
-#define MX31_INT_SDMA (NR_IRQS_LEGACY + 34)
-#define MX31_INT_USB_HS1 (NR_IRQS_LEGACY + 35)
-#define MX31_INT_USB_HS2 (NR_IRQS_LEGACY + 36)
-#define MX31_INT_USB_OTG (NR_IRQS_LEGACY + 37)
-#define MX31_INT_MSHC1 (NR_IRQS_LEGACY + 39)
-#define MX31_INT_MSHC2 (NR_IRQS_LEGACY + 40)
-#define MX31_INT_IPU_ERR (NR_IRQS_LEGACY + 41)
-#define MX31_INT_IPU_SYN (NR_IRQS_LEGACY + 42)
-#define MX31_INT_UART1 (NR_IRQS_LEGACY + 45)
-#define MX31_INT_UART4 (NR_IRQS_LEGACY + 46)
-#define MX31_INT_UART5 (NR_IRQS_LEGACY + 47)
-#define MX31_INT_ECT (NR_IRQS_LEGACY + 48)
-#define MX31_INT_SCC_SCM (NR_IRQS_LEGACY + 49)
-#define MX31_INT_SCC_SMN (NR_IRQS_LEGACY + 50)
-#define MX31_INT_GPIO2 (NR_IRQS_LEGACY + 51)
-#define MX31_INT_GPIO1 (NR_IRQS_LEGACY + 52)
-#define MX31_INT_CCM (NR_IRQS_LEGACY + 53)
-#define MX31_INT_PCMCIA (NR_IRQS_LEGACY + 54)
-#define MX31_INT_WDOG (NR_IRQS_LEGACY + 55)
-#define MX31_INT_GPIO3 (NR_IRQS_LEGACY + 56)
-#define MX31_INT_EXT_POWER (NR_IRQS_LEGACY + 58)
-#define MX31_INT_EXT_TEMPER (NR_IRQS_LEGACY + 59)
-#define MX31_INT_EXT_SENSOR60 (NR_IRQS_LEGACY + 60)
-#define MX31_INT_EXT_SENSOR61 (NR_IRQS_LEGACY + 61)
-#define MX31_INT_EXT_WDOG (NR_IRQS_LEGACY + 62)
-#define MX31_INT_EXT_TV (NR_IRQS_LEGACY + 63)
-
-#define MX31_DMA_REQ_SDHC1 20
-#define MX31_DMA_REQ_SDHC2 21
-#define MX31_DMA_REQ_SSI2_RX1 22
-#define MX31_DMA_REQ_SSI2_TX1 23
-#define MX31_DMA_REQ_SSI2_RX0 24
-#define MX31_DMA_REQ_SSI2_TX0 25
-#define MX31_DMA_REQ_SSI1_RX1 26
-#define MX31_DMA_REQ_SSI1_TX1 27
-#define MX31_DMA_REQ_SSI1_RX0 28
-#define MX31_DMA_REQ_SSI1_TX0 29
-
-#define MX31_PROD_SIGNATURE 0x1 /* For MX31 */
#endif /* ifndef __MACH_MX31_H__ */
diff --git a/arch/arm/mach-imx/mx31lilly-db.c b/arch/arm/mach-imx/mx31lilly-db.c
deleted file mode 100644
index 00a5ee3..0000000
--- a/arch/arm/mach-imx/mx31lilly-db.c
+++ /dev/null
@@ -1,182 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LILLY-1131 development board support
- *
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * based on code for other MX31 boards,
- *
- * Copyright 2005-2007 Freescale Semiconductor
- * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lilly.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * This file contains board-specific initialization routines for the
- * LILLY-1131 development board. If you design an own baseboard for the
- * module, use this file as base for support code.
- */
-
-static unsigned int lilly_db_board_pins[] __initdata = {
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
- MX31_PIN_LD0__LD0,
- MX31_PIN_LD1__LD1,
- MX31_PIN_LD2__LD2,
- MX31_PIN_LD3__LD3,
- MX31_PIN_LD4__LD4,
- MX31_PIN_LD5__LD5,
- MX31_PIN_LD6__LD6,
- MX31_PIN_LD7__LD7,
- MX31_PIN_LD8__LD8,
- MX31_PIN_LD9__LD9,
- MX31_PIN_LD10__LD10,
- MX31_PIN_LD11__LD11,
- MX31_PIN_LD12__LD12,
- MX31_PIN_LD13__LD13,
- MX31_PIN_LD14__LD14,
- MX31_PIN_LD15__LD15,
- MX31_PIN_LD16__LD16,
- MX31_PIN_LD17__LD17,
- MX31_PIN_VSYNC3__VSYNC3,
- MX31_PIN_HSYNC__HSYNC,
- MX31_PIN_FPSHIFT__FPSHIFT,
- MX31_PIN_DRDY0__DRDY0,
- MX31_PIN_CONTRAST__CONTRAST,
-};
-
-/* MMC support */
-
-static int mxc_mmc1_get_ro(struct device *dev)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_LCS0));
-}
-
-static int gpio_det, gpio_wp;
-
-#define MMC_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int mxc_mmc1_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
-{
- int ret;
-
- gpio_det = IOMUX_TO_GPIO(MX31_PIN_GPIO1_1);
- gpio_wp = IOMUX_TO_GPIO(MX31_PIN_LCS0);
-
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA0, MMC_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA1, MMC_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA2, MMC_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA3, MMC_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SD1_CLK, MMC_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SD1_CMD, MMC_PAD_CFG);
-
- ret = gpio_request(gpio_det, "MMC detect");
- if (ret)
- return ret;
-
- ret = gpio_request(gpio_wp, "MMC w/p");
- if (ret)
- goto exit_free_det;
-
- gpio_direction_input(gpio_det);
- gpio_direction_input(gpio_wp);
-
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)),
- detect_irq, IRQF_TRIGGER_FALLING,
- "MMC detect", data);
- if (ret)
- goto exit_free_wp;
-
- return 0;
-
-exit_free_wp:
- gpio_free(gpio_wp);
-
-exit_free_det:
- gpio_free(gpio_det);
-
- return ret;
-}
-
-static void mxc_mmc1_exit(struct device *dev, void *data)
-{
- gpio_free(gpio_det);
- gpio_free(gpio_wp);
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)), data);
-}
-
-static const struct imxmmc_platform_data mmc_pdata __initconst = {
- .get_ro = mxc_mmc1_get_ro,
- .init = mxc_mmc1_init,
- .exit = mxc_mmc1_exit,
-};
-
-/* Framebuffer support */
-static const struct fb_videomode fb_modedb = {
- /* 640x480 TFT panel (IPS-056T) */
- .name = "CRT-VGA",
- .refresh = 64,
- .xres = 640,
- .yres = 480,
- .pixclock = 30000,
- .left_margin = 200,
- .right_margin = 2,
- .upper_margin = 2,
- .lower_margin = 2,
- .hsync_len = 3,
- .vsync_len = 1,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
-};
-
-static struct mx3fb_platform_data fb_pdata __initdata = {
- .name = "CRT-VGA",
- .mode = &fb_modedb,
- .num_modes = 1,
-};
-
-#define LCD_VCC_EN_GPIO (7)
-
-static void __init mx31lilly_init_fb(void)
-{
- if (gpio_request(LCD_VCC_EN_GPIO, "LCD enable") != 0) {
- printk(KERN_WARNING "unable to request LCD_VCC_EN pin.\n");
- return;
- }
-
- imx31_add_ipu_core();
- imx31_add_mx3_sdc_fb(&fb_pdata);
- gpio_direction_output(LCD_VCC_EN_GPIO, 1);
-}
-
-void __init mx31lilly_db_init(void)
-{
- mxc_iomux_setup_multiple_pins(lilly_db_board_pins,
- ARRAY_SIZE(lilly_db_board_pins),
- "development board pins");
- imx31_add_mxc_mmc(0, &mmc_pdata);
- mx31lilly_init_fb();
-}
diff --git a/arch/arm/mach-imx/mx31lite-db.c b/arch/arm/mach-imx/mx31lite-db.c
deleted file mode 100644
index 13da732..0000000
--- a/arch/arm/mach-imx/mx31lite-db.c
+++ /dev/null
@@ -1,154 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LogicPD i.MX31 SOM-LV development board support
- *
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * based on code for other MX31 boards,
- *
- * Copyright 2005-2007 Freescale Semiconductor
- * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lite.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * This file contains board-specific initialization routines for the
- * LogicPD i.MX31 SOM-LV development board, aka 'LiteKit'.
- * If you design an own baseboard for the module, use this file as base
- * for support code.
- */
-
-static unsigned int litekit_db_board_pins[] __initdata = {
- /* SDHC1 */
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
-};
-
-/* MMC */
-
-static int gpio_det, gpio_wp;
-
-#define MMC_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS)
-
-static int mxc_mmc1_get_ro(struct device *dev)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_GPIO1_6));
-}
-
-static int mxc_mmc1_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
-{
- int ret;
-
- gpio_det = IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1);
- gpio_wp = IOMUX_TO_GPIO(MX31_PIN_GPIO1_6);
-
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA0,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA1,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA2,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA3,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_CMD,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_CLK, MMC_PAD_CFG);
-
- ret = gpio_request(gpio_det, "MMC detect");
- if (ret)
- return ret;
-
- ret = gpio_request(gpio_wp, "MMC w/p");
- if (ret)
- goto exit_free_det;
-
- gpio_direction_input(gpio_det);
- gpio_direction_input(gpio_wp);
-
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)),
- detect_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC detect", data);
- if (ret)
- goto exit_free_wp;
-
- return 0;
-
-exit_free_wp:
- gpio_free(gpio_wp);
-
-exit_free_det:
- gpio_free(gpio_det);
-
- return ret;
-}
-
-static void mxc_mmc1_exit(struct device *dev, void *data)
-{
- gpio_free(gpio_det);
- gpio_free(gpio_wp);
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)), data);
-}
-
-static const struct imxmmc_platform_data mmc_pdata __initconst = {
- .get_ro = mxc_mmc1_get_ro,
- .init = mxc_mmc1_init,
- .exit = mxc_mmc1_exit,
-};
-
-/* GPIO LEDs */
-
-static const struct gpio_led litekit_leds[] __initconst = {
- {
- .name = "GPIO0",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_COMPARE),
- .active_low = 1,
- .default_state = LEDS_GPIO_DEFSTATE_OFF,
- },
- {
- .name = "GPIO1",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_CAPTURE),
- .active_low = 1,
- .default_state = LEDS_GPIO_DEFSTATE_OFF,
- }
-};
-
-static const struct gpio_led_platform_data
- litekit_led_platform_data __initconst = {
- .leds = litekit_leds,
- .num_leds = ARRAY_SIZE(litekit_leds),
-};
-
-void __init mx31lite_db_init(void)
-{
- mxc_iomux_setup_multiple_pins(litekit_db_board_pins,
- ARRAY_SIZE(litekit_db_board_pins),
- "development board pins");
- imx31_add_mxc_mmc(0, &mmc_pdata);
- gpio_led_register_device(-1, &litekit_led_platform_data);
- imx31_add_imx2_wdt();
- imx31_add_mxc_rtc();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-devboard.c b/arch/arm/mach-imx/mx31moboard-devboard.c
deleted file mode 100644
index 6a9db06..0000000
--- a/arch/arm/mach-imx/mx31moboard-devboard.c
+++ /dev/null
@@ -1,238 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int devboard_pins[] = {
- /* UART1 */
- MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2,
- MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2,
- /* SDHC2 */
- MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2,
- MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0,
- MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD,
- MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29,
- /* USB H1 */
- MX31_PIN_CSPI1_MISO__USBH1_RXDP, MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
- MX31_PIN_CSPI1_SS0__USBH1_TXDM, MX31_PIN_CSPI1_SS1__USBH1_TXDP,
- MX31_PIN_CSPI1_SS2__USBH1_RCV, MX31_PIN_CSPI1_SCLK__USBH1_OEB,
- MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, MX31_PIN_SFS6__USBH1_SUSPEND,
- MX31_PIN_NFRE_B__GPIO1_11, MX31_PIN_NFALE__GPIO1_12,
- /* SEL */
- MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
- MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR)
-#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW)
-
-static int devboard_sdhc2_get_ro(struct device *dev)
-{
- return !gpio_get_value(SDHC2_WP);
-}
-
-static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request(SDHC2_CD, "sdhc-detect");
- if (ret)
- return ret;
-
- gpio_direction_input(SDHC2_CD);
-
- ret = gpio_request(SDHC2_WP, "sdhc-wp");
- if (ret)
- goto err_gpio_free;
- gpio_direction_input(SDHC2_WP);
-
- ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "sdhc2-card-detect", data);
- if (ret)
- goto err_gpio_free_2;
-
- return 0;
-
-err_gpio_free_2:
- gpio_free(SDHC2_WP);
-err_gpio_free:
- gpio_free(SDHC2_CD);
-
- return ret;
-}
-
-static void devboard_sdhc2_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(SDHC2_CD), data);
- gpio_free(SDHC2_WP);
- gpio_free(SDHC2_CD);
-}
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
- .get_ro = devboard_sdhc2_get_ro,
- .init = devboard_sdhc2_init,
- .exit = devboard_sdhc2_exit,
-};
-
-#define SEL0 IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define SEL1 IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define SEL2 IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define SEL3 IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void devboard_init_sel_gpios(void)
-{
- if (!gpio_request(SEL0, "sel0")) {
- gpio_direction_input(SEL0);
- gpio_export(SEL0, true);
- }
-
- if (!gpio_request(SEL1, "sel1")) {
- gpio_direction_input(SEL1);
- gpio_export(SEL1, true);
- }
-
- if (!gpio_request(SEL2, "sel2")) {
- gpio_direction_input(SEL2);
- gpio_export(SEL2, true);
- }
-
- if (!gpio_request(SEL3, "sel3")) {
- gpio_direction_input(SEL3);
- gpio_export(SEL3, true);
- }
-}
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int devboard_usbh1_hw_init(struct platform_device *pdev)
-{
- mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SFS6, USB_PAD_CFG);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-#define USBH1_VBUSEN_B IOMUX_TO_GPIO(MX31_PIN_NFRE_B)
-#define USBH1_MODE IOMUX_TO_GPIO(MX31_PIN_NFALE)
-
-static int devboard_isp1105_init(struct usb_phy *otg)
-{
- int ret = gpio_request(USBH1_MODE, "usbh1-mode");
- if (ret)
- return ret;
- /* single ended */
- gpio_direction_output(USBH1_MODE, 0);
-
- ret = gpio_request(USBH1_VBUSEN_B, "usbh1-vbusen");
- if (ret) {
- gpio_free(USBH1_MODE);
- return ret;
- }
- gpio_direction_output(USBH1_VBUSEN_B, 1);
-
- return 0;
-}
-
-
-static int devboard_isp1105_set_vbus(struct usb_otg *otg, bool on)
-{
- if (on)
- gpio_set_value(USBH1_VBUSEN_B, 0);
- else
- gpio_set_value(USBH1_VBUSEN_B, 1);
-
- return 0;
-}
-
-static struct mxc_usbh_platform_data usbh1_pdata __initdata = {
- .init = devboard_usbh1_hw_init,
- .portsc = MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static int __init devboard_usbh1_init(void)
-{
- struct usb_phy *phy;
- struct platform_device *pdev;
-
- phy = kzalloc(sizeof(*phy), GFP_KERNEL);
- if (!phy)
- return -ENOMEM;
-
- phy->otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
- if (!phy->otg) {
- kfree(phy);
- return -ENOMEM;
- }
-
- phy->label = "ISP1105";
- phy->init = devboard_isp1105_init;
- phy->otg->set_vbus = devboard_isp1105_set_vbus;
-
- usbh1_pdata.otg = phy;
-
- pdev = imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
- return PTR_ERR_OR_ZERO(pdev);
-}
-
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_devboard_init(void)
-{
- printk(KERN_INFO "Initializing mx31devboard peripherals\n");
-
- mxc_iomux_setup_multiple_pins(devboard_pins, ARRAY_SIZE(devboard_pins),
- "devboard");
-
- imx31_add_imx_uart1(&uart_pdata);
-
- imx31_add_mxc_mmc(1, &sdhc2_pdata);
-
- devboard_init_sel_gpios();
-
- imx31_add_fsl_usb2_udc(&usb_pdata);
-
- devboard_usbh1_init();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-marxbot.c b/arch/arm/mach-imx/mx31moboard-marxbot.c
deleted file mode 100644
index c269000..0000000
--- a/arch/arm/mach-imx/mx31moboard-marxbot.c
+++ /dev/null
@@ -1,270 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/spi/spi.h>
-#include <linux/slab.h>
-#include <linux/platform_device.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int marxbot_pins[] = {
- /* SDHC2 */
- MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2,
- MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0,
- MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD,
- MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29,
- /* dsPIC resets */
- MX31_PIN_STXD5__GPIO1_21, MX31_PIN_SRXD5__GPIO1_22,
- /*battery detection */
- MX31_PIN_LCS0__GPIO3_23,
- /* USB H1 */
- MX31_PIN_CSPI1_MISO__USBH1_RXDP, MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
- MX31_PIN_CSPI1_SS0__USBH1_TXDM, MX31_PIN_CSPI1_SS1__USBH1_TXDP,
- MX31_PIN_CSPI1_SS2__USBH1_RCV, MX31_PIN_CSPI1_SCLK__USBH1_OEB,
- MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, MX31_PIN_SFS6__USBH1_SUSPEND,
- MX31_PIN_NFRE_B__GPIO1_11, MX31_PIN_NFALE__GPIO1_12,
- /* SEL */
- MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
- MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR)
-#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW)
-
-static int marxbot_sdhc2_get_ro(struct device *dev)
-{
- return !gpio_get_value(SDHC2_WP);
-}
-
-static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
- void *data)
-{
- int ret;
-
- ret = gpio_request(SDHC2_CD, "sdhc-detect");
- if (ret)
- return ret;
-
- gpio_direction_input(SDHC2_CD);
-
- ret = gpio_request(SDHC2_WP, "sdhc-wp");
- if (ret)
- goto err_gpio_free;
- gpio_direction_input(SDHC2_WP);
-
- ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "sdhc2-card-detect", data);
- if (ret)
- goto err_gpio_free_2;
-
- return 0;
-
-err_gpio_free_2:
- gpio_free(SDHC2_WP);
-err_gpio_free:
- gpio_free(SDHC2_CD);
-
- return ret;
-}
-
-static void marxbot_sdhc2_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(SDHC2_CD), data);
- gpio_free(SDHC2_WP);
- gpio_free(SDHC2_CD);
-}
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
- .get_ro = marxbot_sdhc2_get_ro,
- .init = marxbot_sdhc2_init,
- .exit = marxbot_sdhc2_exit,
-};
-
-#define TRSLAT_RST_B IOMUX_TO_GPIO(MX31_PIN_STXD5)
-#define DSPICS_RST_B IOMUX_TO_GPIO(MX31_PIN_SRXD5)
-
-static void dspics_resets_init(void)
-{
- if (!gpio_request(TRSLAT_RST_B, "translator-rst")) {
- gpio_direction_output(TRSLAT_RST_B, 0);
- gpio_export(TRSLAT_RST_B, false);
- }
-
- if (!gpio_request(DSPICS_RST_B, "dspics-rst")) {
- gpio_direction_output(DSPICS_RST_B, 0);
- gpio_export(DSPICS_RST_B, false);
- }
-}
-
-static struct spi_board_info marxbot_spi_board_info[] __initdata = {
- {
- .modalias = "spidev",
- .max_speed_hz = 300000,
- .bus_num = 1,
- .chip_select = 1, /* according spi1_cs[] ! */
- },
-};
-
-#define SEL0 IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define SEL1 IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define SEL2 IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define SEL3 IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void marxbot_init_sel_gpios(void)
-{
- if (!gpio_request(SEL0, "sel0")) {
- gpio_direction_input(SEL0);
- gpio_export(SEL0, true);
- }
-
- if (!gpio_request(SEL1, "sel1")) {
- gpio_direction_input(SEL1);
- gpio_export(SEL1, true);
- }
-
- if (!gpio_request(SEL2, "sel2")) {
- gpio_direction_input(SEL2);
- gpio_export(SEL2, true);
- }
-
- if (!gpio_request(SEL3, "sel3")) {
- gpio_direction_input(SEL3);
- gpio_export(SEL3, true);
- }
-}
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int marxbot_usbh1_hw_init(struct platform_device *pdev)
-{
- mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
- mxc_iomux_set_pad(MX31_PIN_SFS6, USB_PAD_CFG);
-
- mdelay(10);
-
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-#define USBH1_VBUSEN_B IOMUX_TO_GPIO(MX31_PIN_NFRE_B)
-#define USBH1_MODE IOMUX_TO_GPIO(MX31_PIN_NFALE)
-
-static int marxbot_isp1105_init(struct usb_phy *otg)
-{
- int ret = gpio_request(USBH1_MODE, "usbh1-mode");
- if (ret)
- return ret;
- /* single ended */
- gpio_direction_output(USBH1_MODE, 0);
-
- ret = gpio_request(USBH1_VBUSEN_B, "usbh1-vbusen");
- if (ret) {
- gpio_free(USBH1_MODE);
- return ret;
- }
- gpio_direction_output(USBH1_VBUSEN_B, 1);
-
- return 0;
-}
-
-
-static int marxbot_isp1105_set_vbus(struct usb_otg *otg, bool on)
-{
- if (on)
- gpio_set_value(USBH1_VBUSEN_B, 0);
- else
- gpio_set_value(USBH1_VBUSEN_B, 1);
-
- return 0;
-}
-
-static struct mxc_usbh_platform_data usbh1_pdata __initdata = {
- .init = marxbot_usbh1_hw_init,
- .portsc = MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static int __init marxbot_usbh1_init(void)
-{
- struct usb_phy *phy;
- struct platform_device *pdev;
-
- phy = kzalloc(sizeof(*phy), GFP_KERNEL);
- if (!phy)
- return -ENOMEM;
-
- phy->otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
- if (!phy->otg) {
- kfree(phy);
- return -ENOMEM;
- }
-
- phy->label = "ISP1105";
- phy->init = marxbot_isp1105_init;
- phy->otg->set_vbus = marxbot_isp1105_set_vbus;
-
- usbh1_pdata.otg = phy;
-
- pdev = imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
- return PTR_ERR_OR_ZERO(pdev);
-}
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_marxbot_init(void)
-{
- printk(KERN_INFO "Initializing mx31marxbot peripherals\n");
-
- mxc_iomux_setup_multiple_pins(marxbot_pins, ARRAY_SIZE(marxbot_pins),
- "marxbot");
-
- marxbot_init_sel_gpios();
-
- dspics_resets_init();
-
- imx31_add_mxc_mmc(1, &sdhc2_pdata);
-
- spi_register_board_info(marxbot_spi_board_info,
- ARRAY_SIZE(marxbot_spi_board_info));
-
- /* battery present pin */
- gpio_request(IOMUX_TO_GPIO(MX31_PIN_LCS0), "bat-present");
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_LCS0));
- gpio_export(IOMUX_TO_GPIO(MX31_PIN_LCS0), false);
-
- imx31_add_fsl_usb2_udc(&usb_pdata);
-
- marxbot_usbh1_init();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-smartbot.c b/arch/arm/mach-imx/mx31moboard-smartbot.c
deleted file mode 100644
index d165bd9..0000000
--- a/arch/arm/mach-imx/mx31moboard-smartbot.c
+++ /dev/null
@@ -1,124 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/platform_device.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int smartbot_pins[] = {
- /* UART1 */
- MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2,
- MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2,
- /* ENABLES */
- MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
- MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_ULPI,
-};
-
-#if defined(CONFIG_USB_ULPI)
-
-static int smartbot_otg_init(struct platform_device *pdev)
-{
- return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data otg_host_pdata __initdata = {
- .init = smartbot_otg_init,
- .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static int __init smartbot_otg_host_init(void)
-{
- struct platform_device *pdev;
-
- otg_host_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
- ULPI_OTG_DRVVBUS_EXT);
- if (!otg_host_pdata.otg)
- return -ENODEV;
-
- pdev = imx31_add_mxc_ehci_otg(&otg_host_pdata);
-
- return PTR_ERR_OR_ZERO(pdev);
-}
-#else
-static inline int smartbot_otg_host_init(void) { return 0; }
-#endif
-
-#define POWER_EN IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define DSPIC_RST_B IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define TRSLAT_RST_B IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define TRSLAT_SRC_CHOICE IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void smartbot_resets_init(void)
-{
- if (!gpio_request(POWER_EN, "power-enable")) {
- gpio_direction_output(POWER_EN, 0);
- gpio_export(POWER_EN, false);
- }
-
- if (!gpio_request(DSPIC_RST_B, "dspic-rst")) {
- gpio_direction_output(DSPIC_RST_B, 0);
- gpio_export(DSPIC_RST_B, false);
- }
-
- if (!gpio_request(TRSLAT_RST_B, "translator-rst")) {
- gpio_direction_output(TRSLAT_RST_B, 0);
- gpio_export(TRSLAT_RST_B, false);
- }
-
- if (!gpio_request(TRSLAT_SRC_CHOICE, "translator-src-choice")) {
- gpio_direction_output(TRSLAT_SRC_CHOICE, 0);
- gpio_export(TRSLAT_SRC_CHOICE, false);
- }
-}
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_smartbot_init(int board)
-{
- printk(KERN_INFO "Initializing mx31smartbot peripherals\n");
-
- mxc_iomux_setup_multiple_pins(smartbot_pins, ARRAY_SIZE(smartbot_pins),
- "smartbot");
-
- imx31_add_imx_uart1(&uart_pdata);
-
- switch (board) {
- case MX31SMARTBOT:
- imx31_add_fsl_usb2_udc(&usb_pdata);
- break;
- case MX31EYEBOT:
- smartbot_otg_host_init();
- break;
- default:
- printk(KERN_WARNING "Unknown board %d, USB OTG not initialized",
- board);
- }
-
- smartbot_resets_init();
-}
diff --git a/arch/arm/mach-imx/mx35.h b/arch/arm/mach-imx/mx35.h
index 760de6a..5a8a87a 100644
--- a/arch/arm/mach-imx/mx35.h
+++ b/arch/arm/mach-imx/mx35.h
@@ -2,190 +2,17 @@
#ifndef __MACH_MX35_H__
#define __MACH_MX35_H__
-/*
- * IRAM
- */
-#define MX35_IRAM_BASE_ADDR 0x10000000 /* internal ram */
-#define MX35_IRAM_SIZE SZ_128K
-
-#define MX35_L2CC_BASE_ADDR 0x30000000
-#define MX35_L2CC_SIZE SZ_1M
-
#define MX35_AIPS1_BASE_ADDR 0x43f00000
#define MX35_AIPS1_SIZE SZ_1M
-#define MX35_MAX_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x04000)
-#define MX35_EVTMON_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x08000)
-#define MX35_CLKCTL_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x0c000)
-#define MX35_ETB_SLOT4_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x10000)
-#define MX35_ETB_SLOT5_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x14000)
-#define MX35_ECT_CTIO_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x18000)
-#define MX35_I2C1_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x80000)
-#define MX35_I2C3_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x84000)
-#define MX35_UART1_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x90000)
-#define MX35_UART2_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x94000)
-#define MX35_I2C2_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x98000)
-#define MX35_OWIRE_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0x9c000)
-#define MX35_SSI1_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xa0000)
-#define MX35_CSPI1_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xa4000)
-#define MX35_KPP_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xa8000)
-#define MX35_IOMUXC_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xac000)
-#define MX35_ECT_IP1_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xb8000)
-#define MX35_ECT_IP2_BASE_ADDR (MX35_AIPS1_BASE_ADDR + 0xbc000)
-
#define MX35_SPBA0_BASE_ADDR 0x50000000
#define MX35_SPBA0_SIZE SZ_1M
-#define MX35_UART3_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x0c000)
-#define MX35_CSPI2_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x10000)
-#define MX35_SSI2_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x14000)
-#define MX35_ATA_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x20000)
-#define MX35_MSHC1_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x24000)
-#define MX35_FEC_BASE_ADDR 0x50038000
-#define MX35_SPBA_CTRL_BASE_ADDR (MX35_SPBA0_BASE_ADDR + 0x3c000)
-
#define MX35_AIPS2_BASE_ADDR 0x53f00000
#define MX35_AIPS2_SIZE SZ_1M
-#define MX35_CCM_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0x80000)
-#define MX35_GPT1_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0x90000)
-#define MX35_EPIT1_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0x94000)
-#define MX35_EPIT2_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0x98000)
-#define MX35_GPIO3_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xa4000)
-#define MX35_SCC_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xac000)
-#define MX35_RNGA_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xb0000)
-#define MX35_ESDHC1_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xb4000)
-#define MX35_ESDHC2_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xb8000)
-#define MX35_ESDHC3_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xbc000)
-#define MX35_IPU_CTRL_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xc0000)
-#define MX35_AUDMUX_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xc4000)
-#define MX35_GPIO1_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xcc000)
-#define MX35_GPIO2_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xd0000)
-#define MX35_SDMA_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xd4000)
-#define MX35_RTC_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xd8000)
-#define MX35_WDOG_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xdc000)
-#define MX35_PWM_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xe0000)
-#define MX35_CAN1_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xe4000)
-#define MX35_CAN2_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xe8000)
-#define MX35_RTIC_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xec000)
-#define MX35_IIM_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xf0000)
-#define MX35_USB_BASE_ADDR (MX35_AIPS2_BASE_ADDR + 0xf4000)
-#define MX35_USB_OTG_BASE_ADDR (MX35_USB_BASE_ADDR + 0x0000)
-/*
- * The Reference Manual (IMX35RM, Rev. 2, 3/2009) claims an offset of 0x200 for
- * HS. When host support was implemented only a preliminary document was
- * available, which told 0x400. This works fine.
- */
-#define MX35_USB_HS_BASE_ADDR (MX35_USB_BASE_ADDR + 0x0400)
-
-#define MX35_ROMP_BASE_ADDR 0x60000000
-#define MX35_ROMP_SIZE SZ_1M
-
#define MX35_AVIC_BASE_ADDR 0x68000000
#define MX35_AVIC_SIZE SZ_1M
-
-/*
- * Memory regions and CS
- */
-#define MX35_IPU_MEM_BASE_ADDR 0x70000000
-#define MX35_CSD0_BASE_ADDR 0x80000000
-#define MX35_CSD1_BASE_ADDR 0x90000000
-
-#define MX35_CS0_BASE_ADDR 0xa0000000
-#define MX35_CS1_BASE_ADDR 0xa8000000
-#define MX35_CS2_BASE_ADDR 0xb0000000
-#define MX35_CS3_BASE_ADDR 0xb2000000
-
-#define MX35_CS4_BASE_ADDR 0xb4000000
-#define MX35_CS4_BASE_ADDR_VIRT 0xf6000000
-#define MX35_CS4_SIZE SZ_32M
-
-#define MX35_CS5_BASE_ADDR 0xb6000000
-#define MX35_CS5_BASE_ADDR_VIRT 0xf8000000
-#define MX35_CS5_SIZE SZ_32M
-
-/*
- * NAND, SDRAM, WEIM, M3IF, EMI controllers
- */
#define MX35_X_MEMC_BASE_ADDR 0xb8000000
#define MX35_X_MEMC_SIZE SZ_64K
-#define MX35_ESDCTL_BASE_ADDR (MX35_X_MEMC_BASE_ADDR + 0x1000)
-#define MX35_WEIM_BASE_ADDR (MX35_X_MEMC_BASE_ADDR + 0x2000)
-#define MX35_M3IF_BASE_ADDR (MX35_X_MEMC_BASE_ADDR + 0x3000)
-#define MX35_EMI_CTL_BASE_ADDR (MX35_X_MEMC_BASE_ADDR + 0x4000)
-#define MX35_PCMCIA_CTL_BASE_ADDR MX35_EMI_CTL_BASE_ADDR
-
-#define MX35_NFC_BASE_ADDR 0xbb000000
-#define MX35_PCMCIA_MEM_BASE_ADDR 0xbc000000
#define MX35_IO_P2V(x) IMX_IO_P2V(x)
-#define MX35_IO_ADDRESS(x) IOMEM(MX35_IO_P2V(x))
-
-/*
- * Interrupt numbers
- */
-#include <asm/irq.h>
-#define MX35_INT_OWIRE (NR_IRQS_LEGACY + 2)
-#define MX35_INT_I2C3 (NR_IRQS_LEGACY + 3)
-#define MX35_INT_I2C2 (NR_IRQS_LEGACY + 4)
-#define MX35_INT_RTIC (NR_IRQS_LEGACY + 6)
-#define MX35_INT_ESDHC1 (NR_IRQS_LEGACY + 7)
-#define MX35_INT_ESDHC2 (NR_IRQS_LEGACY + 8)
-#define MX35_INT_ESDHC3 (NR_IRQS_LEGACY + 9)
-#define MX35_INT_I2C1 (NR_IRQS_LEGACY + 10)
-#define MX35_INT_SSI1 (NR_IRQS_LEGACY + 11)
-#define MX35_INT_SSI2 (NR_IRQS_LEGACY + 12)
-#define MX35_INT_CSPI2 (NR_IRQS_LEGACY + 13)
-#define MX35_INT_CSPI1 (NR_IRQS_LEGACY + 14)
-#define MX35_INT_ATA (NR_IRQS_LEGACY + 15)
-#define MX35_INT_GPU2D (NR_IRQS_LEGACY + 16)
-#define MX35_INT_ASRC (NR_IRQS_LEGACY + 17)
-#define MX35_INT_UART3 (NR_IRQS_LEGACY + 18)
-#define MX35_INT_IIM (NR_IRQS_LEGACY + 19)
-#define MX35_INT_RNGA (NR_IRQS_LEGACY + 22)
-#define MX35_INT_EVTMON (NR_IRQS_LEGACY + 23)
-#define MX35_INT_KPP (NR_IRQS_LEGACY + 24)
-#define MX35_INT_RTC (NR_IRQS_LEGACY + 25)
-#define MX35_INT_PWM (NR_IRQS_LEGACY + 26)
-#define MX35_INT_EPIT2 (NR_IRQS_LEGACY + 27)
-#define MX35_INT_EPIT1 (NR_IRQS_LEGACY + 28)
-#define MX35_INT_GPT (NR_IRQS_LEGACY + 29)
-#define MX35_INT_POWER_FAIL (NR_IRQS_LEGACY + 30)
-#define MX35_INT_UART2 (NR_IRQS_LEGACY + 32)
-#define MX35_INT_NFC (NR_IRQS_LEGACY + 33)
-#define MX35_INT_SDMA (NR_IRQS_LEGACY + 34)
-#define MX35_INT_USB_HS (NR_IRQS_LEGACY + 35)
-#define MX35_INT_USB_OTG (NR_IRQS_LEGACY + 37)
-#define MX35_INT_MSHC1 (NR_IRQS_LEGACY + 39)
-#define MX35_INT_ESAI (NR_IRQS_LEGACY + 40)
-#define MX35_INT_IPU_ERR (NR_IRQS_LEGACY + 41)
-#define MX35_INT_IPU_SYN (NR_IRQS_LEGACY + 42)
-#define MX35_INT_CAN1 (NR_IRQS_LEGACY + 43)
-#define MX35_INT_CAN2 (NR_IRQS_LEGACY + 44)
-#define MX35_INT_UART1 (NR_IRQS_LEGACY + 45)
-#define MX35_INT_MLB (NR_IRQS_LEGACY + 46)
-#define MX35_INT_SPDIF (NR_IRQS_LEGACY + 47)
-#define MX35_INT_ECT (NR_IRQS_LEGACY + 48)
-#define MX35_INT_SCC_SCM (NR_IRQS_LEGACY + 49)
-#define MX35_INT_SCC_SMN (NR_IRQS_LEGACY + 50)
-#define MX35_INT_GPIO2 (NR_IRQS_LEGACY + 51)
-#define MX35_INT_GPIO1 (NR_IRQS_LEGACY + 52)
-#define MX35_INT_WDOG (NR_IRQS_LEGACY + 55)
-#define MX35_INT_GPIO3 (NR_IRQS_LEGACY + 56)
-#define MX35_INT_FEC (NR_IRQS_LEGACY + 57)
-#define MX35_INT_EXT_POWER (NR_IRQS_LEGACY + 58)
-#define MX35_INT_EXT_TEMPER (NR_IRQS_LEGACY + 59)
-#define MX35_INT_EXT_SENSOR60 (NR_IRQS_LEGACY + 60)
-#define MX35_INT_EXT_SENSOR61 (NR_IRQS_LEGACY + 61)
-#define MX35_INT_EXT_WDOG (NR_IRQS_LEGACY + 62)
-#define MX35_INT_EXT_TV (NR_IRQS_LEGACY + 63)
-
-#define MX35_DMA_REQ_SSI2_RX1 22
-#define MX35_DMA_REQ_SSI2_TX1 23
-#define MX35_DMA_REQ_SSI2_RX0 24
-#define MX35_DMA_REQ_SSI2_TX0 25
-#define MX35_DMA_REQ_SSI1_RX1 26
-#define MX35_DMA_REQ_SSI1_TX1 27
-#define MX35_DMA_REQ_SSI1_RX0 28
-#define MX35_DMA_REQ_SSI1_TX0 29
-
-#define MX35_PROD_SIGNATURE 0x1 /* For MX31 */
#endif /* ifndef __MACH_MX35_H__ */
diff --git a/arch/arm/mach-imx/pcm037.h b/arch/arm/mach-imx/pcm037.h
deleted file mode 100644
index 470d3c8..0000000
--- a/arch/arm/mach-imx/pcm037.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __PCM037_H__
-#define __PCM037_H__
-
-enum pcm037_board_variant {
- PCM037_PCM970,
- PCM037_EET,
-};
-
-extern enum pcm037_board_variant pcm037_variant(void);
-
-#ifdef CONFIG_MACH_PCM037_EET
-int pcm037_eet_init_devices(void);
-#else
-static inline int pcm037_eet_init_devices(void) { return 0; }
-#endif
-
-#endif
diff --git a/arch/arm/mach-imx/pm-imx27.c b/arch/arm/mach-imx/pm-imx27.c
index d943535..020e6de 100644
--- a/arch/arm/mach-imx/pm-imx27.c
+++ b/arch/arm/mach-imx/pm-imx27.c
@@ -7,6 +7,7 @@
* modify it under the terms of the GNU General Public License.
*/
+#include <linux/of_address.h>
#include <linux/kernel.h>
#include <linux/suspend.h>
#include <linux/io.h>
@@ -15,13 +16,20 @@
static int mx27_suspend_enter(suspend_state_t state)
{
+ void __iomem *ccm_base;
+ struct device_node *np;
u32 cscr;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
+ ccm_base = of_iomap(np, 0);
+ BUG_ON(!ccm_base);
+
switch (state) {
case PM_SUSPEND_MEM:
/* Clear MPEN and SPEN to disable MPLL/SPLL */
- cscr = imx_readl(MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+ cscr = imx_readl(ccm_base);
cscr &= 0xFFFFFFFC;
- imx_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+ imx_writel(cscr, ccm_base);
/* Executes WFI */
cpu_do_idle();
break;
diff --git a/arch/arm/mach-imx/ulpi.h b/arch/arm/mach-imx/ulpi.h
deleted file mode 100644
index b367902..0000000
--- a/arch/arm/mach-imx/ulpi.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __MACH_ULPI_H
-#define __MACH_ULPI_H
-
-#include <linux/usb/ulpi.h>
-
-#ifdef CONFIG_USB_ULPI_VIEWPORT
-static inline struct usb_phy *imx_otg_ulpi_create(unsigned int flags)
-{
- return otg_ulpi_create(&ulpi_viewport_access_ops, flags);
-}
-#else
-static inline struct usb_phy *imx_otg_ulpi_create(unsigned int flags)
-{
- return NULL;
-}
-#endif
-
-#endif /* __MACH_ULPI_H */
-
diff --git a/arch/arm/mach-mstar/Kconfig b/arch/arm/mach-mstar/Kconfig
index 52744fe..576d1ab 100644
--- a/arch/arm/mach-mstar/Kconfig
+++ b/arch/arm/mach-mstar/Kconfig
@@ -3,6 +3,7 @@
depends on ARCH_MULTI_V7
select ARM_GIC
select ARM_HEAVY_MB
+ select MST_IRQ
help
Support for newer MStar/Sigmastar SoC families that are
based on Armv7 cores like the Cortex A7 and share the same
diff --git a/arch/arm/mach-omap1/include/mach/mux.h b/arch/arm/mach-omap1/include/mach/mux.h
index adfe1f6..3f6dc55 100644
--- a/arch/arm/mach-omap1/include/mach/mux.h
+++ b/arch/arm/mach-omap1/include/mach/mux.h
@@ -88,7 +88,7 @@
* OMAP730/850 has a slightly different config for the pin mux.
* - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
* not the FUNC_MUX_CTRL_x regs from hardware.h
- * - for pull-up/down, only has one enable bit which is is in the same register
+ * - for pull-up/down, only has one enable bit which is in the same register
* as mux config
*/
#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode, \
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index ea23205..3ee7bdf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -7,6 +7,7 @@
depends on ARCH_MULTI_V6
select ARCH_OMAP2PLUS
select CPU_V6
+ select PM_GENERIC_DOMAINS if PM
select SOC_HAS_OMAP2_SDRC
config ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/am33xx.h b/arch/arm/mach-omap2/am33xx.h
index 5eef093..bf2b5f8 100644
--- a/arch/arm/mach-omap2/am33xx.h
+++ b/arch/arm/mach-omap2/am33xx.h
@@ -1,7 +1,7 @@
/*
* This file contains the address info for various AM33XX modules.
*
- * Copyright (C) 2011 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments, Inc. - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 334923d..7290f03 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -3,7 +3,7 @@
* Copyright (C) 2005 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
*
* Modified from the original mach-omap/omap2/board-generic.c did by Paul
* to support the OMAP2+ device tree boards with an unique board file.
diff --git a/arch/arm/mach-omap2/clockdomains33xx_data.c b/arch/arm/mach-omap2/clockdomains33xx_data.c
index 32c90fd..b4d5144 100644
--- a/arch/arm/mach-omap2/clockdomains33xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains33xx_data.c
@@ -1,7 +1,7 @@
/*
* AM33XX Clock Domain data.
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
* Vaibhav Hiremath <hvaibhav@ti.com>
*
* This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/clockdomains81xx_data.c b/arch/arm/mach-omap2/clockdomains81xx_data.c
index 65fbd13..127dc7a 100644
--- a/arch/arm/mach-omap2/clockdomains81xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains81xx_data.c
@@ -1,7 +1,7 @@
/*
* TI81XX Clock Domain data.
*
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
* Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
*
* This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/cm-regbits-33xx.h b/arch/arm/mach-omap2/cm-regbits-33xx.h
index c0823fd..e7ae2bb 100644
--- a/arch/arm/mach-omap2/cm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-33xx.h
@@ -4,7 +4,7 @@
* This file is automatically generated from the AM33XX hardware databases.
* Vaibhav Hiremath <hvaibhav@ti.com>
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/cm-regbits-54xx.h b/arch/arm/mach-omap2/cm-regbits-54xx.h
index 44663b5..fc88688 100644
--- a/arch/arm/mach-omap2/cm-regbits-54xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54xx Clock Management register bits
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley (paul@pwsan.com)
* Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm-regbits-7xx.h b/arch/arm/mach-omap2/cm-regbits-7xx.h
index a78ccba..2725af4 100644
--- a/arch/arm/mach-omap2/cm-regbits-7xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-7xx.h
@@ -2,7 +2,7 @@
/*
* DRA7xx Clock Management register bits
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Generated by code originally written by:
* Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm1_54xx.h b/arch/arm/mach-omap2/cm1_54xx.h
index 7be363a..eb86bbd 100644
--- a/arch/arm/mach-omap2/cm1_54xx.h
+++ b/arch/arm/mach-omap2/cm1_54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54xx CM1 instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley (paul@pwsan.com)
* Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm1_7xx.h b/arch/arm/mach-omap2/cm1_7xx.h
index 28660ed..aae3831 100644
--- a/arch/arm/mach-omap2/cm1_7xx.h
+++ b/arch/arm/mach-omap2/cm1_7xx.h
@@ -2,7 +2,7 @@
/*
* DRA7xx CM1 instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Generated by code originally written by:
* Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm2_54xx.h b/arch/arm/mach-omap2/cm2_54xx.h
index c5da1f5..8e49765 100644
--- a/arch/arm/mach-omap2/cm2_54xx.h
+++ b/arch/arm/mach-omap2/cm2_54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54xx CM2 instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley (paul@pwsan.com)
* Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm2_7xx.h b/arch/arm/mach-omap2/cm2_7xx.h
index e16fc58..f873460 100644
--- a/arch/arm/mach-omap2/cm2_7xx.h
+++ b/arch/arm/mach-omap2/cm2_7xx.h
@@ -2,7 +2,7 @@
/*
* DRA7xx CM2 instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Generated by code originally written by:
* Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm33xx.c b/arch/arm/mach-omap2/cm33xx.c
index 084d454..ac4882e 100644
--- a/arch/arm/mach-omap2/cm33xx.c
+++ b/arch/arm/mach-omap2/cm33xx.c
@@ -1,7 +1,7 @@
/*
* AM33XX CM functions
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
* Vaibhav Hiremath <hvaibhav@ti.com>
*
* Reference taken from from OMAP4 cminst44xx.c
diff --git a/arch/arm/mach-omap2/cm33xx.h b/arch/arm/mach-omap2/cm33xx.h
index a91f7d2..63b362b 100644
--- a/arch/arm/mach-omap2/cm33xx.h
+++ b/arch/arm/mach-omap2/cm33xx.h
@@ -1,7 +1,7 @@
/*
* AM33XX CM offset macros
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
* Vaibhav Hiremath <hvaibhav@ti.com>
*
* This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/cm81xx.h b/arch/arm/mach-omap2/cm81xx.h
index 5d73a10..bd91223 100644
--- a/arch/arm/mach-omap2/cm81xx.h
+++ b/arch/arm/mach-omap2/cm81xx.h
@@ -1,7 +1,7 @@
/*
* Clock domain register offsets for TI81XX.
*
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
* Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
*
* This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c
index 46012ca..2000fca 100644
--- a/arch/arm/mach-omap2/display.c
+++ b/arch/arm/mach-omap2/display.c
@@ -1,7 +1,7 @@
/*
* OMAP2plus display device setup / initialization.
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Senthilvadivu Guruswamy
* Sumit Semwal
*
diff --git a/arch/arm/mach-omap2/dma.c b/arch/arm/mach-omap2/dma.c
index 8cc109cc..dfc9b21 100644
--- a/arch/arm/mach-omap2/dma.c
+++ b/arch/arm/mach-omap2/dma.c
@@ -13,7 +13,7 @@
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Converted DMA library into platform driver
* - G, Manjunath Kondaiah <manjugk@ti.com>
*/
diff --git a/arch/arm/mach-omap2/l3_2xxx.h b/arch/arm/mach-omap2/l3_2xxx.h
index c2bd8d8..6297c62 100644
--- a/arch/arm/mach-omap2/l3_2xxx.h
+++ b/arch/arm/mach-omap2/l3_2xxx.h
@@ -2,7 +2,7 @@
/*
* arch/arm/plat-omap/include/plat/l3_2xxx.h - L3 firewall definitions
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Sumit Semwal
*/
#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L3_2XXX_H
diff --git a/arch/arm/mach-omap2/l3_3xxx.h b/arch/arm/mach-omap2/l3_3xxx.h
index 995ebcc..60ea7b2 100644
--- a/arch/arm/mach-omap2/l3_3xxx.h
+++ b/arch/arm/mach-omap2/l3_3xxx.h
@@ -2,7 +2,7 @@
/*
* arch/arm/plat-omap/include/plat/l3_3xxx.h - L3 firewall definitions
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Sumit Semwal
*/
#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L3_3XXX_H
diff --git a/arch/arm/mach-omap2/l4_2xxx.h b/arch/arm/mach-omap2/l4_2xxx.h
index 556e69c..418e107 100644
--- a/arch/arm/mach-omap2/l4_2xxx.h
+++ b/arch/arm/mach-omap2/l4_2xxx.h
@@ -2,7 +2,7 @@
/*
* arch/arm/plat-omap/include/plat/l4_2xxx.h - L4 firewall definitions
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Sumit Semwal
*/
#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L4_2XXX_H
diff --git a/arch/arm/mach-omap2/omap-iommu.c b/arch/arm/mach-omap2/omap-iommu.c
index bfa5e1b..93c20bb 100644
--- a/arch/arm/mach-omap2/omap-iommu.c
+++ b/arch/arm/mach-omap2/omap-iommu.c
@@ -2,7 +2,7 @@
/*
* OMAP IOMMU quirks for various TI SoCs
*
- * Copyright (C) 2015-2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015-2019 Texas Instruments Incorporated - https://www.ti.com/
* Suman Anna <s-anna@ti.com>
*/
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
index 5f4ab24..e298410 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
@@ -26,7 +26,6 @@ extern struct omap_hwmod_ocp_if am33xx_mpu__prcm;
extern struct omap_hwmod_ocp_if am33xx_l3_s__l3_main;
extern struct omap_hwmod_ocp_if am33xx_gfx__l3_main;
extern struct omap_hwmod_ocp_if am33xx_l3_main__gfx;
-extern struct omap_hwmod_ocp_if am33xx_l4_wkup__rtc;
extern struct omap_hwmod_ocp_if am33xx_l3_s__gpmc;
extern struct omap_hwmod_ocp_if am33xx_l4_ls__timer2;
extern struct omap_hwmod_ocp_if am33xx_l3_main__ocmc;
@@ -43,7 +42,6 @@ extern struct omap_hwmod am33xx_ocmcram_hwmod;
extern struct omap_hwmod am33xx_smartreflex0_hwmod;
extern struct omap_hwmod am33xx_smartreflex1_hwmod;
extern struct omap_hwmod am33xx_gpmc_hwmod;
-extern struct omap_hwmod am33xx_rtc_hwmod;
extern struct omap_hwmod_class am33xx_emif_hwmod_class;
extern struct omap_hwmod_class am33xx_l4_hwmod_class;
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
index b389d65..ab5146b 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
@@ -74,30 +74,6 @@ struct omap_hwmod_ocp_if am33xx_l3_s__l3_main = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* gfx -> l3 main */
-struct omap_hwmod_ocp_if am33xx_gfx__l3_main = {
- .master = &am33xx_gfx_hwmod,
- .slave = &am33xx_l3_main_hwmod,
- .clk = "dpll_core_m4_ck",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l3 main -> gfx */
-struct omap_hwmod_ocp_if am33xx_l3_main__gfx = {
- .master = &am33xx_l3_main_hwmod,
- .slave = &am33xx_gfx_hwmod,
- .clk = "dpll_core_m4_ck",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4 wkup -> rtc */
-struct omap_hwmod_ocp_if am33xx_l4_wkup__rtc = {
- .master = &am33xx_l4_wkup_hwmod,
- .slave = &am33xx_rtc_hwmod,
- .clk = "clkdiv32k_ick",
- .user = OCP_USER_MPU,
-};
-
/* l3s cfg -> gpmc */
struct omap_hwmod_ocp_if am33xx_l3_s__gpmc = {
.master = &am33xx_l3_s_hwmod,
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
index 4b3cd59..bcc120e 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
@@ -26,7 +26,6 @@
#define CLKCTRL(oh, clkctrl) ((oh).prcm.omap4.clkctrl_offs = (clkctrl))
#define RSTCTRL(oh, rstctrl) ((oh).prcm.omap4.rstctrl_offs = (rstctrl))
#define RSTST(oh, rstst) ((oh).prcm.omap4.rstst_offs = (rstst))
-#define PRCM_FLAGS(oh, flag) ((oh).prcm.omap4.flags = (flag))
/*
* 'l3' class
@@ -133,30 +132,6 @@ struct omap_hwmod_class am33xx_wkup_m3_hwmod_class = {
.name = "wkup_m3",
};
-/* gfx */
-/* Pseudo hwmod for reset control purpose only */
-static struct omap_hwmod_class am33xx_gfx_hwmod_class = {
- .name = "gfx",
-};
-
-static struct omap_hwmod_rst_info am33xx_gfx_resets[] = {
- { .name = "gfx", .rst_shift = 0, .st_shift = 0},
-};
-
-struct omap_hwmod am33xx_gfx_hwmod = {
- .name = "gfx",
- .class = &am33xx_gfx_hwmod_class,
- .clkdm_name = "gfx_l3_clkdm",
- .main_clk = "gfx_fck_div_ck",
- .prcm = {
- .omap4 = {
- .modulemode = MODULEMODE_SWCTRL,
- },
- },
- .rst_lines = am33xx_gfx_resets,
- .rst_lines_cnt = ARRAY_SIZE(am33xx_gfx_resets),
-};
-
/*
* 'prcm' class
* power and reset manager (whole prcm infrastructure)
@@ -274,67 +249,24 @@ struct omap_hwmod am33xx_gpmc_hwmod = {
},
};
-
-/*
- * 'rtc' class
- * rtc subsystem
- */
-static struct omap_hwmod_class_sysconfig am33xx_rtc_sysc = {
- .rev_offs = 0x0074,
- .sysc_offs = 0x0078,
- .sysc_flags = SYSC_HAS_SIDLEMODE,
- .idlemodes = (SIDLE_FORCE | SIDLE_NO |
- SIDLE_SMART | SIDLE_SMART_WKUP),
- .sysc_fields = &omap_hwmod_sysc_type3,
-};
-
-static struct omap_hwmod_class am33xx_rtc_hwmod_class = {
- .name = "rtc",
- .sysc = &am33xx_rtc_sysc,
- .unlock = &omap_hwmod_rtc_unlock,
- .lock = &omap_hwmod_rtc_lock,
-};
-
-struct omap_hwmod am33xx_rtc_hwmod = {
- .name = "rtc",
- .class = &am33xx_rtc_hwmod_class,
- .clkdm_name = "l4_rtc_clkdm",
- .main_clk = "clk_32768_ck",
- .prcm = {
- .omap4 = {
- .modulemode = MODULEMODE_SWCTRL,
- },
- },
-};
-
static void omap_hwmod_am33xx_clkctrl(void)
{
CLKCTRL(am33xx_smartreflex0_hwmod,
AM33XX_CM_WKUP_SMARTREFLEX0_CLKCTRL_OFFSET);
CLKCTRL(am33xx_smartreflex1_hwmod,
AM33XX_CM_WKUP_SMARTREFLEX1_CLKCTRL_OFFSET);
- CLKCTRL(am33xx_rtc_hwmod, AM33XX_CM_RTC_RTC_CLKCTRL_OFFSET);
- PRCM_FLAGS(am33xx_rtc_hwmod, HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET);
CLKCTRL(am33xx_gpmc_hwmod, AM33XX_CM_PER_GPMC_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l4_ls_hwmod, AM33XX_CM_PER_L4LS_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l4_wkup_hwmod, AM33XX_CM_WKUP_L4WKUP_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l3_main_hwmod, AM33XX_CM_PER_L3_CLKCTRL_OFFSET);
- CLKCTRL(am33xx_gfx_hwmod, AM33XX_CM_GFX_GFX_CLKCTRL_OFFSET);
CLKCTRL(am33xx_mpu_hwmod , AM33XX_CM_MPU_MPU_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l3_instr_hwmod , AM33XX_CM_PER_L3_INSTR_CLKCTRL_OFFSET);
CLKCTRL(am33xx_ocmcram_hwmod , AM33XX_CM_PER_OCMCRAM_CLKCTRL_OFFSET);
}
-static void omap_hwmod_am33xx_rst(void)
-{
- RSTCTRL(am33xx_gfx_hwmod, AM33XX_RM_GFX_RSTCTRL_OFFSET);
- RSTST(am33xx_gfx_hwmod, AM33XX_RM_GFX_RSTST_OFFSET);
-}
-
void omap_hwmod_am33xx_reg(void)
{
omap_hwmod_am33xx_clkctrl();
- omap_hwmod_am33xx_rst();
}
static void omap_hwmod_am43xx_clkctrl(void)
@@ -343,25 +275,16 @@ static void omap_hwmod_am43xx_clkctrl(void)
AM43XX_CM_WKUP_SMARTREFLEX0_CLKCTRL_OFFSET);
CLKCTRL(am33xx_smartreflex1_hwmod,
AM43XX_CM_WKUP_SMARTREFLEX1_CLKCTRL_OFFSET);
- CLKCTRL(am33xx_rtc_hwmod, AM43XX_CM_RTC_RTC_CLKCTRL_OFFSET);
CLKCTRL(am33xx_gpmc_hwmod, AM43XX_CM_PER_GPMC_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l4_ls_hwmod, AM43XX_CM_PER_L4LS_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l4_wkup_hwmod, AM43XX_CM_WKUP_L4WKUP_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l3_main_hwmod, AM43XX_CM_PER_L3_CLKCTRL_OFFSET);
- CLKCTRL(am33xx_gfx_hwmod, AM43XX_CM_GFX_GFX_CLKCTRL_OFFSET);
CLKCTRL(am33xx_mpu_hwmod , AM43XX_CM_MPU_MPU_CLKCTRL_OFFSET);
CLKCTRL(am33xx_l3_instr_hwmod , AM43XX_CM_PER_L3_INSTR_CLKCTRL_OFFSET);
CLKCTRL(am33xx_ocmcram_hwmod , AM43XX_CM_PER_OCMCRAM_CLKCTRL_OFFSET);
}
-static void omap_hwmod_am43xx_rst(void)
-{
- RSTCTRL(am33xx_gfx_hwmod, AM43XX_RM_GFX_RSTCTRL_OFFSET);
- RSTST(am33xx_gfx_hwmod, AM43XX_RM_GFX_RSTST_OFFSET);
-}
-
void omap_hwmod_am43xx_reg(void)
{
omap_hwmod_am43xx_clkctrl();
- omap_hwmod_am43xx_rst();
}
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
index 3cf9c4c..b232f6c 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
@@ -1,7 +1,7 @@
/*
* omap_hwmod_33xx_data.c: Hardware modules present on the AM33XX chips
*
- * Copyright (C) {2012} Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) {2012} Texas Instruments Incorporated - https://www.ti.com/
*
* This file is automatically generated from the AM33XX hardware databases.
* This program is free software; you can redistribute it and/or
@@ -274,16 +274,13 @@ static struct omap_hwmod_ocp_if *am33xx_hwmod_ocp_ifs[] __initdata = {
&am33xx_l3_main__l4_hs,
&am33xx_l3_main__l3_s,
&am33xx_l3_main__l3_instr,
- &am33xx_l3_main__gfx,
&am33xx_l3_s__l3_main,
&am33xx_wkup_m3__l4_wkup,
- &am33xx_gfx__l3_main,
&am33xx_l3_main__debugss,
&am33xx_l4_wkup__wkup_m3,
&am33xx_l4_wkup__control,
&am33xx_l4_wkup__smartreflex0,
&am33xx_l4_wkup__smartreflex1,
- &am33xx_l4_wkup__rtc,
&am33xx_l3_s__gpmc,
&am33xx_l3_main__ocmc,
NULL,
diff --git a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
index b88d12d..b97cb74 100644
--- a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
@@ -143,11 +143,9 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
&am43xx_l3_main__l4_hs,
&am33xx_l3_main__l3_s,
&am33xx_l3_main__l3_instr,
- &am33xx_l3_main__gfx,
&am33xx_l3_s__l3_main,
&am43xx_l3_main__emif,
&am43xx_wkup_m3__l4_wkup,
- &am33xx_gfx__l3_main,
&am43xx_l4_wkup__wkup_m3,
&am43xx_l4_wkup__control,
&am43xx_l4_wkup__smartreflex0,
@@ -157,11 +155,6 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
NULL,
};
-static struct omap_hwmod_ocp_if *am43xx_rtc_hwmod_ocp_ifs[] __initdata = {
- &am33xx_l4_wkup__rtc,
- NULL,
-};
-
int __init am43xx_hwmod_init(void)
{
int ret;
@@ -170,8 +163,5 @@ int __init am43xx_hwmod_init(void)
omap_hwmod_init();
ret = omap_hwmod_register_links(am43xx_hwmod_ocp_ifs);
- if (!ret && of_machine_is_compatible("ti,am4372"))
- ret = omap_hwmod_register_links(am43xx_rtc_hwmod_ocp_ifs);
-
return ret;
}
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 665ca74..37c5911 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -124,21 +124,6 @@ static struct omap_hwmod_class omap44xx_l4_hwmod_class = {
.name = "l4",
};
-/* l4_abe */
-static struct omap_hwmod omap44xx_l4_abe_hwmod = {
- .name = "l4_abe",
- .class = &omap44xx_l4_hwmod_class,
- .clkdm_name = "abe_clkdm",
- .prcm = {
- .omap4 = {
- .clkctrl_offs = OMAP4_CM1_ABE_L4ABE_CLKCTRL_OFFSET,
- .context_offs = OMAP4_RM_ABE_AESS_CONTEXT_OFFSET,
- .lostcontext_mask = OMAP4430_LOSTMEM_AESSMEM_MASK,
- .flags = HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT,
- },
- },
-};
-
/* l4_cfg */
static struct omap_hwmod omap44xx_l4_cfg_hwmod = {
.name = "l4_cfg",
@@ -771,22 +756,6 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_3 = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l3_main_1 -> l4_abe */
-static struct omap_hwmod_ocp_if omap44xx_l3_main_1__l4_abe = {
- .master = &omap44xx_l3_main_1_hwmod,
- .slave = &omap44xx_l4_abe_hwmod,
- .clk = "l3_div_ck",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* mpu -> l4_abe */
-static struct omap_hwmod_ocp_if omap44xx_mpu__l4_abe = {
- .master = &omap44xx_mpu_hwmod,
- .slave = &omap44xx_l4_abe_hwmod,
- .clk = "ocp_abe_iclk",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
/* l3_main_1 -> l4_cfg */
static struct omap_hwmod_ocp_if omap44xx_l3_main_1__l4_cfg = {
.master = &omap44xx_l3_main_1_hwmod,
@@ -988,8 +957,6 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = {
&omap44xx_l3_main_1__l3_main_3,
&omap44xx_l3_main_2__l3_main_3,
&omap44xx_l4_cfg__l3_main_3,
- &omap44xx_l3_main_1__l4_abe,
- &omap44xx_mpu__l4_abe,
&omap44xx_l3_main_1__l4_cfg,
&omap44xx_l3_main_2__l4_per,
&omap44xx_l4_cfg__l4_wkup,
diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
index 7c38c1b..85b9ab4 100644
--- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
@@ -2,7 +2,7 @@
/*
* Hardware modules present on the OMAP54xx chips
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley
* Benoit Cousson
@@ -121,19 +121,6 @@ static struct omap_hwmod_class omap54xx_l4_hwmod_class = {
.name = "l4",
};
-/* l4_abe */
-static struct omap_hwmod omap54xx_l4_abe_hwmod = {
- .name = "l4_abe",
- .class = &omap54xx_l4_hwmod_class,
- .clkdm_name = "abe_clkdm",
- .prcm = {
- .omap4 = {
- .clkctrl_offs = OMAP54XX_CM_ABE_L4_ABE_CLKCTRL_OFFSET,
- .flags = HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT,
- },
- },
-};
-
/* l4_cfg */
static struct omap_hwmod omap54xx_l4_cfg_hwmod = {
.name = "l4_cfg",
@@ -395,22 +382,6 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_3 = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l3_main_1 -> l4_abe */
-static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l4_abe = {
- .master = &omap54xx_l3_main_1_hwmod,
- .slave = &omap54xx_l4_abe_hwmod,
- .clk = "abe_iclk",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* mpu -> l4_abe */
-static struct omap_hwmod_ocp_if omap54xx_mpu__l4_abe = {
- .master = &omap54xx_mpu_hwmod,
- .slave = &omap54xx_l4_abe_hwmod,
- .clk = "abe_iclk",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
/* l3_main_1 -> l4_cfg */
static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l4_cfg = {
.master = &omap54xx_l3_main_1_hwmod,
@@ -478,8 +449,6 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
&omap54xx_l3_main_1__l3_main_3,
&omap54xx_l3_main_2__l3_main_3,
&omap54xx_l4_cfg__l3_main_3,
- &omap54xx_l3_main_1__l4_abe,
- &omap54xx_mpu__l4_abe,
&omap54xx_l3_main_1__l4_cfg,
&omap54xx_l3_main_2__l4_per,
&omap54xx_l3_main_1__l4_wkup,
diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
index adb0784..05e163c 100644
--- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
@@ -2,7 +2,7 @@
/*
* Hardware modules present on the DRA7xx chips
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley
* Benoit Cousson
@@ -419,41 +419,6 @@ static struct omap_hwmod dra7xx_qspi_hwmod = {
};
/*
- * 'rtcss' class
- *
- */
-static struct omap_hwmod_class_sysconfig dra7xx_rtcss_sysc = {
- .rev_offs = 0x0074,
- .sysc_offs = 0x0078,
- .sysc_flags = SYSC_HAS_SIDLEMODE,
- .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
- SIDLE_SMART_WKUP),
- .sysc_fields = &omap_hwmod_sysc_type3,
-};
-
-static struct omap_hwmod_class dra7xx_rtcss_hwmod_class = {
- .name = "rtcss",
- .sysc = &dra7xx_rtcss_sysc,
- .unlock = &omap_hwmod_rtc_unlock,
- .lock = &omap_hwmod_rtc_lock,
-};
-
-/* rtcss */
-static struct omap_hwmod dra7xx_rtcss_hwmod = {
- .name = "rtcss",
- .class = &dra7xx_rtcss_hwmod_class,
- .clkdm_name = "rtc_clkdm",
- .main_clk = "sys_32k_ck",
- .prcm = {
- .omap4 = {
- .clkctrl_offs = DRA7XX_CM_RTC_RTCSS_CLKCTRL_OFFSET,
- .context_offs = DRA7XX_RM_RTC_RTCSS_CONTEXT_OFFSET,
- .modulemode = MODULEMODE_SWCTRL,
- },
- },
-};
-
-/*
* 'sata' class
*
*/
@@ -702,14 +667,6 @@ static struct omap_hwmod_ocp_if dra7xx_l3_main_1__qspi = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-/* l4_per3 -> rtcss */
-static struct omap_hwmod_ocp_if dra7xx_l4_per3__rtcss = {
- .master = &dra7xx_l4_per3_hwmod,
- .slave = &dra7xx_rtcss_hwmod,
- .clk = "l4_root_clk_div",
- .user = OCP_USER_MPU | OCP_USER_SDMA,
-};
-
/* l4_cfg -> sata */
static struct omap_hwmod_ocp_if dra7xx_l4_cfg__sata = {
.master = &dra7xx_l4_cfg_hwmod,
@@ -786,7 +743,6 @@ static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
};
static struct omap_hwmod_ocp_if *rtc_hwmod_ocp_ifs[] __initdata = {
- &dra7xx_l4_per3__rtcss,
NULL,
};
diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
index 50fb699..450ab99 100644
--- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
@@ -1,7 +1,7 @@
/*
* DM81xx hwmod data.
*
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
* Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
*
* This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/omap_opp_data.h b/arch/arm/mach-omap2/omap_opp_data.h
index 336fdfc..533dd64 100644
--- a/arch/arm/mach-omap2/omap_opp_data.h
+++ b/arch/arm/mach-omap2/omap_opp_data.h
@@ -1,7 +1,7 @@
/*
* OMAP SoC specific OPP Data helpers
*
- * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2009-2010 Texas Instruments Incorporated - https://www.ti.com/
* Nishanth Menon
* Kevin Hilman
* Copyright (C) 2010 Nokia Corporation.
diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index d2925e8..6f6a6a6 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -3,7 +3,7 @@
* This file configures the internal USB PHY in OMAP4430. Used
* with TWL6030 transceiver and MUSB on OMAP4430.
*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com
* Author: Hema HK <hemahk@ti.com>
*/
diff --git a/arch/arm/mach-omap2/opp3xxx_data.c b/arch/arm/mach-omap2/opp3xxx_data.c
index c2d459f..b610c5f 100644
--- a/arch/arm/mach-omap2/opp3xxx_data.c
+++ b/arch/arm/mach-omap2/opp3xxx_data.c
@@ -1,7 +1,7 @@
/*
* OMAP3 OPP table definitions.
*
- * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2009-2010 Texas Instruments Incorporated - https://www.ti.com/
* Nishanth Menon
* Kevin Hilman
* Copyright (C) 2010-2011 Nokia Corporation.
diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c
index 985aeab..d937c5e 100644
--- a/arch/arm/mach-omap2/opp4xxx_data.c
+++ b/arch/arm/mach-omap2/opp4xxx_data.c
@@ -1,7 +1,7 @@
/*
* OMAP4 OPP table definitions.
*
- * Copyright (C) 2010-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010-2012 Texas Instruments Incorporated - https://www.ti.com/
* Nishanth Menon
* Kevin Hilman
* Thara Gopinath
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
index fceb1e5..919d35d 100644
--- a/arch/arm/mach-omap2/pm-debug.c
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -34,8 +34,6 @@
#include "prm2xxx_3xxx.h"
#include "pm.h"
-u32 enable_off_mode;
-
#ifdef CONFIG_DEBUG_FS
#include <linux/debugfs.h>
#include <linux/seq_file.h>
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index 01ec1ba..da829a9 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -28,6 +28,8 @@
#include "clockdomain.h"
#include "pm.h"
+u32 enable_off_mode;
+
#ifdef CONFIG_SUSPEND
/*
* omap_pm_suspend: points to a function that does the SoC-specific
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index 2a883a0..80e84ae 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -49,11 +49,7 @@ static inline int omap4_opp_init(void)
extern int omap3_pm_get_suspend_state(struct powerdomain *pwrdm);
extern int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state);
-#ifdef CONFIG_PM_DEBUG
extern u32 enable_off_mode;
-#else
-#define enable_off_mode 0
-#endif
#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
extern void pm_dbg_update_time(struct powerdomain *pwrdm, int prev);
diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c
index 58236c7..56f2c0b 100644
--- a/arch/arm/mach-omap2/pm33xx-core.c
+++ b/arch/arm/mach-omap2/pm33xx-core.c
@@ -2,7 +2,7 @@
/*
* AM33XX Arch Power Management Routines
*
- * Copyright (C) 2016-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016-2018 Texas Instruments Incorporated - https://www.ti.com/
* Dave Gerlach
*/
@@ -25,7 +25,6 @@
#include "control.h"
#include "clockdomain.h"
#include "iomap.h"
-#include "omap_hwmod.h"
#include "pm.h"
#include "powerdomain.h"
#include "prm33xx.h"
@@ -36,7 +35,6 @@
static struct powerdomain *cefuse_pwrdm, *gfx_pwrdm, *per_pwrdm, *mpu_pwrdm;
static struct clockdomain *gfx_l4ls_clkdm;
static void __iomem *scu_base;
-static struct omap_hwmod *rtc_oh;
static int (*idle_fn)(u32 wfi_flags);
@@ -267,13 +265,6 @@ static struct am33xx_pm_sram_addr *amx3_get_sram_addrs(void)
return NULL;
}
-static void __iomem *am43xx_get_rtc_base_addr(void)
-{
- rtc_oh = omap_hwmod_lookup("rtc");
-
- return omap_hwmod_get_mpu_rt_va(rtc_oh);
-}
-
static void am43xx_save_context(void)
{
}
@@ -297,16 +288,6 @@ static void am43xx_restore_context(void)
writel_relaxed(0x0, AM33XX_L4_WK_IO_ADDRESS(0x44df2e14));
}
-static void am43xx_prepare_rtc_suspend(void)
-{
- omap_hwmod_enable(rtc_oh);
-}
-
-static void am43xx_prepare_rtc_resume(void)
-{
- omap_hwmod_idle(rtc_oh);
-}
-
static struct am33xx_pm_platform_data am33xx_ops = {
.init = am33xx_suspend_init,
.deinit = amx3_suspend_deinit,
@@ -317,10 +298,7 @@ static struct am33xx_pm_platform_data am33xx_ops = {
.get_sram_addrs = amx3_get_sram_addrs,
.save_context = am33xx_save_context,
.restore_context = am33xx_restore_context,
- .prepare_rtc_suspend = am43xx_prepare_rtc_suspend,
- .prepare_rtc_resume = am43xx_prepare_rtc_resume,
.check_off_mode_enable = am33xx_check_off_mode_enable,
- .get_rtc_base_addr = am43xx_get_rtc_base_addr,
};
static struct am33xx_pm_platform_data am43xx_ops = {
@@ -333,10 +311,7 @@ static struct am33xx_pm_platform_data am43xx_ops = {
.get_sram_addrs = amx3_get_sram_addrs,
.save_context = am43xx_save_context,
.restore_context = am43xx_restore_context,
- .prepare_rtc_suspend = am43xx_prepare_rtc_suspend,
- .prepare_rtc_resume = am43xx_prepare_rtc_resume,
.check_off_mode_enable = am43xx_check_off_mode_enable,
- .get_rtc_base_addr = am43xx_get_rtc_base_addr,
};
static struct am33xx_pm_platform_data *am33xx_pm_get_pdata(void)
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index f5dfddf..71c1d18 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -25,6 +25,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/slab.h>
+#include <linux/of.h>
#include <linux/omap-gpmc.h>
#include <trace/events/power.h>
@@ -410,7 +411,12 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
if (!pwrst)
return -ENOMEM;
pwrst->pwrdm = pwrdm;
- pwrst->next_state = PWRDM_POWER_RET;
+
+ if (enable_off_mode)
+ pwrst->next_state = PWRDM_POWER_OFF;
+ else
+ pwrst->next_state = PWRDM_POWER_RET;
+
list_add(&pwrst->node, &pwrst_list);
if (pwrdm_has_hdwr_sar(pwrdm))
@@ -444,6 +450,22 @@ static void __init pm_errata_configure(void)
}
}
+static void __init omap3_pm_check_pmic(void)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "ti,twl4030-power-idle");
+ if (!np)
+ np = of_find_compatible_node(NULL, NULL, "ti,twl4030-power-idle-osc-off");
+
+ if (np) {
+ of_node_put(np);
+ enable_off_mode = 1;
+ } else {
+ enable_off_mode = 0;
+ }
+}
+
int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
@@ -477,6 +499,8 @@ int __init omap3_pm_init(void)
goto err2;
}
+ omap3_pm_check_pmic();
+
ret = pwrdm_for_each(pwrdms_setup, NULL);
if (ret) {
pr_err("Failed to setup powerdomains\n");
diff --git a/arch/arm/mach-omap2/powerdomains33xx_data.c b/arch/arm/mach-omap2/powerdomains33xx_data.c
index 869adb8..626055e 100644
--- a/arch/arm/mach-omap2/powerdomains33xx_data.c
+++ b/arch/arm/mach-omap2/powerdomains33xx_data.c
@@ -1,7 +1,7 @@
/*
* AM33XX Power domain data
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prcm43xx.h b/arch/arm/mach-omap2/prcm43xx.h
index 7078a61..899da0ae 100644
--- a/arch/arm/mach-omap2/prcm43xx.h
+++ b/arch/arm/mach-omap2/prcm43xx.h
@@ -1,7 +1,7 @@
/*
* AM43x PRCM defines
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
diff --git a/arch/arm/mach-omap2/prcm_mpu54xx.h b/arch/arm/mach-omap2/prcm_mpu54xx.h
index 6ef3882..bdbfa07 100644
--- a/arch/arm/mach-omap2/prcm_mpu54xx.h
+++ b/arch/arm/mach-omap2/prcm_mpu54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54xx PRCM MPU instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley (paul@pwsan.com)
* Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/prcm_mpu7xx.h b/arch/arm/mach-omap2/prcm_mpu7xx.h
index 33d0013..2e30324 100644
--- a/arch/arm/mach-omap2/prcm_mpu7xx.h
+++ b/arch/arm/mach-omap2/prcm_mpu7xx.h
@@ -2,7 +2,7 @@
/*
* DRA7xx PRCM MPU instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Generated by code originally written by:
* Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/prm-regbits-33xx.h b/arch/arm/mach-omap2/prm-regbits-33xx.h
index 84feece..7dfdff0 100644
--- a/arch/arm/mach-omap2/prm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-33xx.h
@@ -1,7 +1,7 @@
/*
* AM33XX PRM_XXX register bits
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm33xx.c b/arch/arm/mach-omap2/prm33xx.c
index d514166..9144cc0 100644
--- a/arch/arm/mach-omap2/prm33xx.c
+++ b/arch/arm/mach-omap2/prm33xx.c
@@ -1,7 +1,7 @@
/*
* AM33XX PRM functions
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm33xx.h b/arch/arm/mach-omap2/prm33xx.h
index 66302c6..d0b7404 100644
--- a/arch/arm/mach-omap2/prm33xx.h
+++ b/arch/arm/mach-omap2/prm33xx.h
@@ -1,7 +1,7 @@
/*
* AM33XX PRM instance offset macros
*
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm54xx.h b/arch/arm/mach-omap2/prm54xx.h
index ee0f1cc..7329d6f 100644
--- a/arch/arm/mach-omap2/prm54xx.h
+++ b/arch/arm/mach-omap2/prm54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54xx PRM instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Paul Walmsley (paul@pwsan.com)
* Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/prm7xx.h b/arch/arm/mach-omap2/prm7xx.h
index cf99307..e5aee04 100644
--- a/arch/arm/mach-omap2/prm7xx.h
+++ b/arch/arm/mach-omap2/prm7xx.h
@@ -2,7 +2,7 @@
/*
* DRA7xx PRM instance offset macros
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Generated by code originally written by:
* Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/scrm54xx.h b/arch/arm/mach-omap2/scrm54xx.h
index 810d2b1..cb6f3e6 100644
--- a/arch/arm/mach-omap2/scrm54xx.h
+++ b/arch/arm/mach-omap2/scrm54xx.h
@@ -2,7 +2,7 @@
/*
* OMAP54XX SCRM registers and bitfields
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*
* Benoit Cousson (b-cousson@ti.com)
*
diff --git a/arch/arm/mach-omap2/sleep33xx.S b/arch/arm/mach-omap2/sleep33xx.S
index dc22124..ac3d0b3 100644
--- a/arch/arm/mach-omap2/sleep33xx.S
+++ b/arch/arm/mach-omap2/sleep33xx.S
@@ -2,7 +2,7 @@
/*
* Low level suspend code for AM33XX SoCs
*
- * Copyright (C) 2012-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012-2018 Texas Instruments Incorporated - https://www.ti.com/
* Dave Gerlach, Vaibhav Bedia
*/
diff --git a/arch/arm/mach-omap2/sleep43xx.S b/arch/arm/mach-omap2/sleep43xx.S
index 90d2907..832c913 100644
--- a/arch/arm/mach-omap2/sleep43xx.S
+++ b/arch/arm/mach-omap2/sleep43xx.S
@@ -2,7 +2,7 @@
/*
* Low level suspend code for AM43XX SoCs
*
- * Copyright (C) 2013-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013-2018 Texas Instruments Incorporated - https://www.ti.com/
* Dave Gerlach, Vaibhav Bedia
*/
diff --git a/arch/arm/mach-omap2/ti81xx.h b/arch/arm/mach-omap2/ti81xx.h
index a1e6caf..192b0e7 100644
--- a/arch/arm/mach-omap2/ti81xx.h
+++ b/arch/arm/mach-omap2/ti81xx.h
@@ -1,7 +1,7 @@
/*
* This file contains the address data for various TI81XX modules.
*
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/voltagedomains54xx_data.c b/arch/arm/mach-omap2/voltagedomains54xx_data.c
index aac274d..e60d76d 100644
--- a/arch/arm/mach-omap2/voltagedomains54xx_data.c
+++ b/arch/arm/mach-omap2/voltagedomains54xx_data.c
@@ -4,7 +4,7 @@
*
* Based on voltagedomains44xx_data.c
*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
*/
#include <linux/kernel.h>
#include <linux/err.h>
diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/mach-s3c/Kconfig
similarity index 69%
rename from arch/arm/plat-samsung/Kconfig
rename to arch/arm/mach-s3c/Kconfig
index 301e5726..25606e6 100644
--- a/arch/arm/plat-samsung/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig
@@ -2,12 +2,16 @@
#
# Copyright 2009 Simtec Electronics
+source "arch/arm/mach-s3c/Kconfig.s3c24xx"
+source "arch/arm/mach-s3c/Kconfig.s3c64xx"
+
config PLAT_SAMSUNG
bool
- depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_EXYNOS || ARCH_S5PV210
+ depends on PLAT_S3C24XX || ARCH_S3C64XX
default y
select GENERIC_IRQ_CHIP
select NO_IOPORT_MAP
+ select SOC_SAMSUNG
help
Base platform code for all Samsung SoC based systems
@@ -154,7 +158,7 @@
bool
default y if ARCH_S3C24XX
help
- Complie in platform device definition for Watchdog Timer
+ Compile in platform device definition for Watchdog Timer
config S3C_DEV_NAND
bool
@@ -169,7 +173,7 @@
config S3C_DEV_RTC
bool
help
- Complie in platform device definition for RTC
+ Compile in platform device definition for RTC
config SAMSUNG_DEV_ADC
bool
@@ -234,54 +238,6 @@
pinctrl-samsung driver.
endif
-comment "Power management"
-
-config SAMSUNG_PM_DEBUG
- bool "Samsung PM Suspend debug"
- depends on PM && DEBUG_KERNEL
- depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
- depends on DEBUG_EXYNOS_UART || DEBUG_S3C24XX_UART || DEBUG_S3C2410_UART
- help
- Say Y here if you want verbose debugging from the PM Suspend and
- Resume code. See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
- for more information.
-
-config S3C_PM_DEBUG_LED_SMDK
- bool "SMDK LED suspend/resume debugging"
- depends on PM && (MACH_SMDK6410)
- help
- Say Y here to enable the use of the SMDK LEDs on the baseboard
- for debugging of the state of the suspend and resume process.
-
- Note, this currently only works for S3C64XX based SMDK boards.
-
-config SAMSUNG_PM_CHECK
- bool "S3C2410 PM Suspend Memory CRC"
- depends on PM && (PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210)
- select CRC32
- help
- Enable the PM code's memory area checksum over sleep. This option
- will generate CRCs of all blocks of memory, and store them before
- going to sleep. The blocks are then checked on resume for any
- errors.
-
- Note, this can take several seconds depending on memory size
- and CPU speed.
-
- See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
-
-config SAMSUNG_PM_CHECK_CHUNKSIZE
- int "S3C2410 PM Suspend CRC Chunksize (KiB)"
- depends on PM && SAMSUNG_PM_CHECK
- default 64
- help
- Set the chunksize in Kilobytes of the CRC for checking memory
- corruption over suspend and resume. A smaller value will mean that
- the CRC data block will take more memory, but will identify any
- faults with better precision.
-
- See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
-
config SAMSUNG_WAKEMASK
bool
depends on PM
@@ -290,19 +246,5 @@
and above. This code allows a set of interrupt to wakeup-mask
mappings. See <plat/wakeup-mask.h>
-config SAMSUNG_WDT_RESET
- bool
- help
- Compile support for system restart by triggering watchdog reset.
- Used on SoCs that do not provide dedicated reset control.
-
-config DEBUG_S3C_UART
- depends on PLAT_SAMSUNG
- int
- default "0" if DEBUG_S3C_UART0
- default "1" if DEBUG_S3C_UART1
- default "2" if DEBUG_S3C_UART2
- default "3" if DEBUG_S3C_UART3
-
endmenu
endif
diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c/Kconfig.s3c24xx
similarity index 96%
rename from arch/arm/mach-s3c24xx/Kconfig
rename to arch/arm/mach-s3c/Kconfig.s3c24xx
index 7673dde..000e3e2 100644
--- a/arch/arm/mach-s3c24xx/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig.s3c24xx
@@ -123,11 +123,6 @@
This also means that the PLL tables for the selected CPU(s) will
be built which may increase the size of the kernel image.
-config S3C_SETUP_CAMIF
- bool
- help
- Compile in common setup code for S3C CAMIF devices
-
# cpu frequency items common between s3c2410 and s3c2440/s3c2442
config S3C2410_IOTIMING
@@ -137,13 +132,6 @@
Internal node to select io timing code that is common to the s3c2410
and s3c2440/s3c2442 cpu frequency support.
-config S3C2410_CPUFREQ_UTILS
- bool
- depends on ARM_S3C24XX_CPUFREQ
- help
- Internal node to select timing code that is common to the s3c2410
- and s3c2440/s3c244 cpu frequency support.
-
# cpu frequency support common to s3c2412, s3c2413 and s3c2442
config S3C2412_IOTIMING
@@ -468,7 +456,6 @@
select NEW_LEDS
select S3C_DEV_NAND
select S3C_DEV_USB_HOST
- select S3C_SETUP_CAMIF
help
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
available via various sources. It can come with a 3.5" or 7" touch LCD.
diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c/Kconfig.s3c64xx
similarity index 97%
rename from arch/arm/mach-s3c64xx/Kconfig
rename to arch/arm/mach-s3c/Kconfig.s3c64xx
index ac3e356..f3fcb57 100644
--- a/arch/arm/mach-s3c64xx/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig.s3c64xx
@@ -13,15 +13,15 @@
select GPIO_SAMSUNG if ATAGS
select GPIOLIB
select HAVE_S3C2410_I2C if I2C
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_TCM
select PLAT_SAMSUNG
select PM_GENERIC_DOMAINS if PM
select S3C_DEV_NAND if ATAGS
select S3C_GPIO_TRACK if ATAGS
+ select S3C2410_WATCHDOG
select SAMSUNG_ATAGS if ATAGS
select SAMSUNG_WAKEMASK if PM
- select SAMSUNG_WDT_RESET
+ select WATCHDOG
help
Samsung S3C64XX series based systems
@@ -165,7 +165,6 @@
bool "SMDK6410"
depends on ATAGS
select CPU_S3C6410
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_I2C1
select S3C64XX_SETUP_IDE
diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/mach-s3c/Makefile
similarity index 62%
rename from arch/arm/plat-samsung/Makefile
rename to arch/arm/mach-s3c/Makefile
index 3db9d2c..54188d1 100644
--- a/arch/arm/plat-samsung/Makefile
+++ b/arch/arm/mach-s3c/Makefile
@@ -2,9 +2,16 @@
#
# Copyright 2009 Simtec Electronics
-ccflags-$(CONFIG_ARCH_S3C64XX) := -I$(srctree)/arch/arm/mach-s3c64xx/include
ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include
+ifdef CONFIG_ARCH_S3C24XX
+include $(src)/Makefile.s3c24xx
+endif
+
+ifdef CONFIG_ARCH_S3C64XX
+include $(src)/Makefile.s3c64xx
+endif
+
# Objects we always build independent of SoC choice
obj-y += init.o cpu.o
@@ -24,12 +31,7 @@
# PM support
-obj-$(CONFIG_PM_SLEEP) += pm-common.o
-obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm-common.o
-obj-$(CONFIG_SAMSUNG_PM) += pm.o
+obj-$(CONFIG_SAMSUNG_PM) += pm.o pm-common.o
obj-$(CONFIG_SAMSUNG_PM_GPIO) += pm-gpio.o
-obj-$(CONFIG_SAMSUNG_PM_CHECK) += pm-check.o
-obj-$(CONFIG_SAMSUNG_PM_DEBUG) += pm-debug.o
obj-$(CONFIG_SAMSUNG_WAKEMASK) += wakeup-mask.o
-obj-$(CONFIG_SAMSUNG_WDT_RESET) += watchdog-reset.o
diff --git a/arch/arm/mach-s3c24xx/Makefile.boot b/arch/arm/mach-s3c/Makefile.boot
similarity index 100%
rename from arch/arm/mach-s3c24xx/Makefile.boot
rename to arch/arm/mach-s3c/Makefile.boot
diff --git a/arch/arm/mach-s3c24xx/Makefile b/arch/arm/mach-s3c/Makefile.s3c24xx
similarity index 80%
rename from arch/arm/mach-s3c24xx/Makefile
rename to arch/arm/mach-s3c/Makefile.s3c24xx
index 6692f2d..3483ab3 100644
--- a/arch/arm/mach-s3c24xx/Makefile
+++ b/arch/arm/mach-s3c/Makefile.s3c24xx
@@ -7,7 +7,10 @@
# core
-obj-y += common.o
+obj-y += s3c24xx.o
+obj-y += irq-s3c24xx.o
+obj-$(CONFIG_SPI_S3C24XX_FIQ) += irq-s3c24xx-fiq.o
+obj-$(CONFIG_SPI_S3C24XX_FIQ) += irq-s3c24xx-fiq-exports.o
obj-$(CONFIG_CPU_S3C2410) += s3c2410.o
obj-$(CONFIG_S3C2410_PLL) += pll-s3c2410.o
@@ -30,12 +33,12 @@
# PM
-obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_PM_SLEEP) += irq-pm.o sleep.o
+obj-$(CONFIG_PM) += pm-s3c24xx.o
+obj-$(CONFIG_PM_SLEEP) += irq-pm-s3c24xx.o sleep-s3c24xx.o
# common code
-obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += cpufreq-utils.o
+obj-$(CONFIG_ARM_S3C24XX_CPUFREQ) += cpufreq-utils-s3c24xx.o
obj-$(CONFIG_S3C2410_IOTIMING) += iotiming-s3c2410.o
obj-$(CONFIG_S3C2412_IOTIMING) += iotiming-s3c2412.o
@@ -80,7 +83,7 @@
# common bits of machine support
-obj-$(CONFIG_S3C24XX_SMDK) += common-smdk.o
+obj-$(CONFIG_S3C24XX_SMDK) += common-smdk-s3c24xx.o
obj-$(CONFIG_S3C24XX_SIMTEC_AUDIO) += simtec-audio.o
obj-$(CONFIG_S3C24XX_SIMTEC_NOR) += simtec-nor.o
obj-$(CONFIG_S3C24XX_SIMTEC_PM) += simtec-pm.o
@@ -93,8 +96,7 @@
# device setup
-obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
-obj-$(CONFIG_S3C2443_SETUP_SPI) += setup-spi.o
-obj-$(CONFIG_ARCH_S3C24XX) += setup-i2c.o
-obj-$(CONFIG_S3C24XX_SETUP_TS) += setup-ts.o
-obj-$(CONFIG_S3C_SETUP_CAMIF) += setup-camif.o
+obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO) += setup-sdhci-gpio-s3c24xx.o
+obj-$(CONFIG_S3C2443_SETUP_SPI) += setup-spi-s3c24xx.o
+obj-$(CONFIG_ARCH_S3C24XX) += setup-i2c-s3c24xx.o
+obj-$(CONFIG_S3C24XX_SETUP_TS) += setup-ts-s3c24xx.o
diff --git a/arch/arm/mach-s3c/Makefile.s3c64xx b/arch/arm/mach-s3c/Makefile.s3c64xx
new file mode 100644
index 0000000..0c18e31
--- /dev/null
+++ b/arch/arm/mach-s3c/Makefile.s3c64xx
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Copyright 2008 Openmoko, Inc.
+# Copyright 2008 Simtec Electronics
+
+ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+
+# PM
+
+obj-$(CONFIG_PM) += pm-s3c64xx.o
+obj-$(CONFIG_PM_SLEEP) += sleep-s3c64xx.o
+obj-$(CONFIG_CPU_IDLE) += cpuidle-s3c64xx.o
+
+ifdef CONFIG_SAMSUNG_ATAGS
+
+obj-$(CONFIG_PM_SLEEP) += irq-pm-s3c64xx.o
+
+# Core
+
+obj-y += s3c64xx.o
+obj-$(CONFIG_CPU_S3C6400) += s3c6400.o
+obj-$(CONFIG_CPU_S3C6410) += s3c6410.o
+
+# DMA support
+
+obj-$(CONFIG_S3C64XX_PL080) += pl080.o
+
+# Device support
+
+obj-y += dev-uart-s3c64xx.o
+obj-y += dev-audio-s3c64xx.o
+
+# Device setup
+
+obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy-s3c64xx.o
+
+obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT) += dev-backlight-s3c64xx.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_ANW6410) += mach-anw6410.o
+obj-$(CONFIG_MACH_HMT) += mach-hmt.o
+obj-$(CONFIG_MACH_MINI6410) += mach-mini6410.o
+obj-$(CONFIG_MACH_NCP) += mach-ncp.o
+obj-$(CONFIG_MACH_REAL6410) += mach-real6410.o
+obj-$(CONFIG_MACH_SMARTQ) += mach-smartq.o
+obj-$(CONFIG_MACH_SMARTQ5) += mach-smartq5.o
+obj-$(CONFIG_MACH_SMARTQ7) += mach-smartq7.o
+obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o
+obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o
+obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
+endif
+
+obj-$(CONFIG_MACH_S3C64XX_DT) += mach-s3c64xx-dt.o
diff --git a/arch/arm/plat-samsung/include/plat/adc-core.h b/arch/arm/mach-s3c/adc-core.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/adc-core.h
rename to arch/arm/mach-s3c/adc-core.h
diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/mach-s3c/adc.c
similarity index 99%
rename from arch/arm/plat-samsung/adc.c
rename to arch/arm/mach-s3c/adc.c
index 55b1925..0232520 100644
--- a/arch/arm/plat-samsung/adc.c
+++ b/arch/arm/mach-s3c/adc.c
@@ -19,8 +19,8 @@
#include <linux/io.h>
#include <linux/regulator/consumer.h>
-#include <plat/regs-adc.h>
-#include <plat/adc.h>
+#include "regs-adc.h"
+#include <linux/soc/samsung/s3c-adc.h>
/* This driver is designed to control the usage of the ADC block between
* the touchscreen and any other drivers that may need to use it, such as
diff --git a/arch/arm/mach-s3c24xx/anubis.h b/arch/arm/mach-s3c/anubis.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/anubis.h
rename to arch/arm/mach-s3c/anubis.h
diff --git a/arch/arm/mach-s3c64xx/ata-core.h b/arch/arm/mach-s3c/ata-core-s3c64xx.h
similarity index 77%
rename from arch/arm/mach-s3c64xx/ata-core.h
rename to arch/arm/mach-s3c/ata-core-s3c64xx.h
index 6d9a81f..4863ad9 100644
--- a/arch/arm/mach-s3c64xx/ata-core.h
+++ b/arch/arm/mach-s3c/ata-core-s3c64xx.h
@@ -6,8 +6,8 @@
* Samsung CF-ATA Controller core functions
*/
-#ifndef __ASM_PLAT_ATA_CORE_H
-#define __ASM_PLAT_ATA_CORE_H __FILE__
+#ifndef __ASM_PLAT_ATA_CORE_S3C64XX_H
+#define __ASM_PLAT_ATA_CORE_S3C64XX_H __FILE__
/* These functions are only for use with the core support code, such as
* the cpu specific initialisation code
@@ -21,4 +21,4 @@ static inline void s3c_cfcon_setname(char *name)
#endif
}
-#endif /* __ASM_PLAT_ATA_CORE_H */
+#endif /* __ASM_PLAT_ATA_CORE_S3C64XX_H */
diff --git a/arch/arm/mach-s3c64xx/backlight.h b/arch/arm/mach-s3c/backlight-s3c64xx.h
similarity index 77%
rename from arch/arm/mach-s3c64xx/backlight.h
rename to arch/arm/mach-s3c/backlight-s3c64xx.h
index 028663f..2a2b358 100644
--- a/arch/arm/mach-s3c64xx/backlight.h
+++ b/arch/arm/mach-s3c/backlight-s3c64xx.h
@@ -4,8 +4,8 @@
* http://www.samsung.com
*/
-#ifndef __ASM_PLAT_BACKLIGHT_H
-#define __ASM_PLAT_BACKLIGHT_H __FILE__
+#ifndef __ASM_PLAT_BACKLIGHT_S3C64XX_H
+#define __ASM_PLAT_BACKLIGHT_S3C64XX_H __FILE__
/* samsung_bl_gpio_info - GPIO info for PWM Backlight control
* @no: GPIO number for PWM timer out
@@ -19,4 +19,4 @@ struct samsung_bl_gpio_info {
extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
struct platform_pwm_backlight_data *bl_data);
-#endif /* __ASM_PLAT_BACKLIGHT_H */
+#endif /* __ASM_PLAT_BACKLIGHT_S3C64XX_H */
diff --git a/arch/arm/mach-s3c24xx/bast-ide.c b/arch/arm/mach-s3c/bast-ide.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/bast-ide.c
rename to arch/arm/mach-s3c/bast-ide.c
index 0679443..da64db1 100644
--- a/arch/arm/mach-s3c24xx/bast-ide.c
+++ b/arch/arm/mach-s3c/bast-ide.c
@@ -19,7 +19,8 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/map.h>
+#include "map.h"
+#include <mach/irqs.h>
#include "bast.h"
diff --git a/arch/arm/mach-s3c24xx/bast-irq.c b/arch/arm/mach-s3c/bast-irq.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/bast-irq.c
rename to arch/arm/mach-s3c/bast-irq.c
index 0372805..d299f12 100644
--- a/arch/arm/mach-s3c24xx/bast-irq.c
+++ b/arch/arm/mach-s3c/bast-irq.c
@@ -15,8 +15,8 @@
#include <asm/mach-types.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/regs-irq.h>
+#include "regs-irq.h"
+#include <mach/irqs.h>
#include "bast.h"
@@ -62,7 +62,7 @@ bast_pc104_mask(struct irq_data *data)
static void
bast_pc104_maskack(struct irq_data *data)
{
- struct irq_desc *desc = irq_desc + BAST_IRQ_ISA;
+ struct irq_desc *desc = irq_to_desc(BAST_IRQ_ISA);
bast_pc104_mask(data);
desc->irq_data.chip->irq_ack(&desc->irq_data);
@@ -94,8 +94,6 @@ static void bast_irq_pc104_demux(struct irq_desc *desc)
if (unlikely(stat == 0)) {
/* ack if we get an irq with nothing (ie, startup) */
-
- desc = irq_desc + BAST_IRQ_ISA;
desc->irq_data.chip->irq_ack(&desc->irq_data);
} else {
/* handle the IRQ */
diff --git a/arch/arm/mach-s3c24xx/bast.h b/arch/arm/mach-s3c/bast.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/bast.h
rename to arch/arm/mach-s3c/bast.h
diff --git a/arch/arm/mach-s3c24xx/common-smdk.c b/arch/arm/mach-s3c/common-smdk-s3c24xx.c
similarity index 95%
rename from arch/arm/mach-s3c24xx/common-smdk.c
rename to arch/arm/mach-s3c/common-smdk-s3c24xx.c
index 121646a..f860d8b 100644
--- a/arch/arm/mach-s3c24xx/common-smdk.c
+++ b/arch/arm/mach-s3c/common-smdk-s3c24xx.c
@@ -29,19 +29,18 @@
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/leds-s3c24xx.h>
#include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "pm.h"
-#include "common-smdk.h"
+#include "common-smdk-s3c24xx.h"
/* LED devices */
diff --git a/arch/arm/mach-s3c24xx/common-smdk.h b/arch/arm/mach-s3c/common-smdk-s3c24xx.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/common-smdk.h
rename to arch/arm/mach-s3c/common-smdk-s3c24xx.h
diff --git a/arch/arm/plat-samsung/cpu.c b/arch/arm/mach-s3c/cpu.c
similarity index 62%
rename from arch/arm/plat-samsung/cpu.c
rename to arch/arm/mach-s3c/cpu.c
index e1ba88b..6e97725 100644
--- a/arch/arm/plat-samsung/cpu.c
+++ b/arch/arm/mach-s3c/cpu.c
@@ -10,17 +10,10 @@
#include <linux/init.h>
#include <linux/io.h>
-#include <plat/map-base.h>
-#include <plat/cpu.h>
+#include <mach/map-base.h>
+#include "cpu.h"
unsigned long samsung_cpu_id;
-static unsigned int samsung_cpu_rev;
-
-unsigned int samsung_rev(void)
-{
- return samsung_cpu_rev;
-}
-EXPORT_SYMBOL(samsung_rev);
void __init s3c64xx_init_cpu(void)
{
@@ -34,15 +27,5 @@ void __init s3c64xx_init_cpu(void)
samsung_cpu_id = readl_relaxed(S3C_VA_SYS + 0xA1C);
}
- samsung_cpu_rev = 0;
-
- pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
-}
-
-void __init s5p_init_cpu(const void __iomem *cpuid_addr)
-{
- samsung_cpu_id = readl_relaxed(cpuid_addr);
- samsung_cpu_rev = samsung_cpu_id & 0xFF;
-
pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
}
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/mach-s3c/cpu.h
similarity index 89%
rename from arch/arm/plat-samsung/include/plat/cpu.h
rename to arch/arm/mach-s3c/cpu.h
index fadcddb..20ff98d 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/mach-s3c/cpu.h
@@ -109,9 +109,6 @@ extern void s3c_init_cpu(unsigned long idcode,
extern void s3c24xx_init_io(struct map_desc *mach_desc, int size);
extern void s3c64xx_init_cpu(void);
-extern void s5p_init_cpu(const void __iomem *cpuid_addr);
-
-extern unsigned int samsung_rev(void);
extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no);
@@ -126,15 +123,6 @@ extern struct syscore_ops s3c2412_pm_syscore_ops;
extern struct syscore_ops s3c2416_pm_syscore_ops;
extern struct syscore_ops s3c244x_pm_syscore_ops;
-/* system device subsystems */
-
-extern struct bus_type s3c2410_subsys;
-extern struct bus_type s3c2410a_subsys;
-extern struct bus_type s3c2412_subsys;
-extern struct bus_type s3c2416_subsys;
-extern struct bus_type s3c2440_subsys;
-extern struct bus_type s3c2442_subsys;
-extern struct bus_type s3c2443_subsys;
extern struct bus_type s3c6410_subsys;
#endif
diff --git a/arch/arm/mach-s3c24xx/cpufreq-utils.c b/arch/arm/mach-s3c/cpufreq-utils-s3c24xx.c
similarity index 68%
rename from arch/arm/mach-s3c24xx/cpufreq-utils.c
rename to arch/arm/mach-s3c/cpufreq-utils-s3c24xx.c
index 1a7f38d..c1784d8 100644
--- a/arch/arm/mach-s3c24xx/cpufreq-utils.c
+++ b/arch/arm/mach-s3c/cpufreq-utils-s3c24xx.c
@@ -12,12 +12,12 @@
#include <linux/io.h>
#include <linux/clk.h>
-#include <mach/map.h>
-#include <mach/regs-clock.h>
+#include "map.h"
+#include "regs-clock.h"
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
/**
* s3c2410_cpufreq_setrefresh - set SDRAM refresh value
@@ -60,3 +60,35 @@ void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg)
if (!IS_ERR(cfg->mpll))
clk_set_rate(cfg->mpll, cfg->pll.frequency);
}
+
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
+u32 s3c2440_read_camdivn(void)
+{
+ return __raw_readl(S3C2440_CAMDIVN);
+}
+
+void s3c2440_write_camdivn(u32 camdiv)
+{
+ __raw_writel(camdiv, S3C2440_CAMDIVN);
+}
+#endif
+
+u32 s3c24xx_read_clkdivn(void)
+{
+ return __raw_readl(S3C2410_CLKDIVN);
+}
+
+void s3c24xx_write_clkdivn(u32 clkdiv)
+{
+ __raw_writel(clkdiv, S3C2410_CLKDIVN);
+}
+
+u32 s3c24xx_read_mpllcon(void)
+{
+ return __raw_readl(S3C2410_MPLLCON);
+}
+
+void s3c24xx_write_locktime(u32 locktime)
+{
+ return __raw_writel(locktime, S3C2410_LOCKTIME);
+}
diff --git a/arch/arm/mach-s3c64xx/cpuidle.c b/arch/arm/mach-s3c/cpuidle-s3c64xx.c
similarity index 91%
rename from arch/arm/mach-s3c64xx/cpuidle.c
rename to arch/arm/mach-s3c/cpuidle-s3c64xx.c
index 0bac6f6..b1c5f43 100644
--- a/arch/arm/mach-s3c64xx/cpuidle.c
+++ b/arch/arm/mach-s3c/cpuidle-s3c64xx.c
@@ -13,11 +13,11 @@
#include <asm/cpuidle.h>
-#include <plat/cpu.h>
-#include <mach/map.h>
+#include "cpu.h"
+#include "map.h"
-#include "regs-sys.h"
-#include "regs-syscon-power.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-syscon-power-s3c64xx.h"
static int s3c64xx_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
diff --git a/arch/arm/mach-s3c64xx/crag6410.h b/arch/arm/mach-s3c/crag6410.h
similarity index 94%
rename from arch/arm/mach-s3c64xx/crag6410.h
rename to arch/arm/mach-s3c/crag6410.h
index 00d9aa1..f39ea2c 100644
--- a/arch/arm/mach-s3c64xx/crag6410.h
+++ b/arch/arm/mach-s3c/crag6410.h
@@ -8,7 +8,7 @@
#ifndef MACH_CRAG6410_H
#define MACH_CRAG6410_H
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
#define GLENFARCLAS_PMIC_IRQ_BASE IRQ_BOARD_START
#define BANFF_PMIC_IRQ_BASE (IRQ_BOARD_START + 64)
diff --git a/arch/arm/mach-s3c64xx/dev-audio.c b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
similarity index 96%
rename from arch/arm/mach-s3c64xx/dev-audio.c
rename to arch/arm/mach-s3c/dev-audio-s3c64xx.c
index e3c49b5..fc2f077 100644
--- a/arch/arm/mach-s3c64xx/dev-audio.c
+++ b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
@@ -11,13 +11,12 @@
#include <linux/export.h>
#include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/dma.h>
+#include "map.h"
-#include <plat/devs.h>
+#include "devs.h"
#include <linux/platform_data/asoc-s3c.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
static int s3c64xx_i2s_cfg_gpio(struct platform_device *pdev)
{
diff --git a/arch/arm/mach-s3c64xx/dev-backlight.c b/arch/arm/mach-s3c/dev-backlight-s3c64xx.c
similarity index 97%
rename from arch/arm/mach-s3c64xx/dev-backlight.c
rename to arch/arm/mach-s3c/dev-backlight-s3c64xx.c
index 09e6da30..65488b6 100644
--- a/arch/arm/mach-s3c64xx/dev-backlight.c
+++ b/arch/arm/mach-s3c/dev-backlight-s3c64xx.c
@@ -11,10 +11,10 @@
#include <linux/io.h>
#include <linux/pwm_backlight.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
+#include "devs.h"
+#include "gpio-cfg.h"
-#include "backlight.h"
+#include "backlight-s3c64xx.h"
struct samsung_bl_drvdata {
struct platform_pwm_backlight_data plat_data;
diff --git a/arch/arm/mach-s3c64xx/dev-uart.c b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
similarity index 94%
rename from arch/arm/mach-s3c64xx/dev-uart.c
rename to arch/arm/mach-s3c/dev-uart-s3c64xx.c
index 5fb59ad..8288e8d 100644
--- a/arch/arm/mach-s3c64xx/dev-uart.c
+++ b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
@@ -15,11 +15,10 @@
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
#include <mach/irqs.h>
-#include <plat/devs.h>
+#include "devs.h"
/* Serial port registrations */
diff --git a/arch/arm/plat-samsung/dev-uart.c b/arch/arm/mach-s3c/dev-uart.c
similarity index 96%
rename from arch/arm/plat-samsung/dev-uart.c
rename to arch/arm/mach-s3c/dev-uart.c
index 7476a5d..3d1f7f2 100644
--- a/arch/arm/plat-samsung/dev-uart.c
+++ b/arch/arm/mach-s3c/dev-uart.c
@@ -10,7 +10,7 @@
#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <plat/devs.h>
+#include "devs.h"
/* uart devices */
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/mach-s3c/devs.c
similarity index 95%
rename from arch/arm/plat-samsung/devs.c
rename to arch/arm/mach-s3c/devs.c
index 089a176..06dec64 100644
--- a/arch/arm/plat-samsung/devs.c
+++ b/arch/arm/mach-s3c/devs.c
@@ -5,6 +5,7 @@
//
// Base Samsung platform device definitions
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
@@ -37,28 +38,32 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/dma.h>
#include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/adc.h>
+#ifdef CONFIG_PLAT_S3C24XX
+#include "regs-s3c2443-clock.h"
+#endif /* CONFIG_PLAT_S3C24XX */
+
+#include "cpu.h"
+#include "devs.h"
+#include <linux/soc/samsung/s3c-adc.h>
#include <linux/platform_data/ata-samsung_cf.h>
-#include <plat/fb.h>
-#include <plat/fb-s3c2410.h>
+#include "fb.h"
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/hwmon-s3c.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/keypad.h>
+#include "keypad.h"
#include <linux/platform_data/mmc-s3cmci.h>
#include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/pwm-core.h>
-#include <plat/sdhci.h>
+#include "pwm-core.h"
+#include "sdhci.h"
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/usb-phy.h>
-#include <plat/regs-spi.h>
+#include "usb-phy.h"
#include <linux/platform_data/asoc-s3c.h>
#include <linux/platform_data/spi-s3c64xx.h>
@@ -833,16 +838,42 @@ struct platform_device s3c_device_rtc = {
/* SDI */
#ifdef CONFIG_PLAT_S3C24XX
+void s3c24xx_mci_def_set_power(unsigned char power_mode, unsigned short vdd)
+{
+ switch (power_mode) {
+ case MMC_POWER_ON:
+ case MMC_POWER_UP:
+ /* Configure GPE5...GPE10 pins in SD mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(5), 6, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+ break;
+
+ case MMC_POWER_OFF:
+ default:
+ gpio_direction_output(S3C2410_GPE(5), 0);
+ break;
+ }
+}
+
static struct resource s3c_sdi_resource[] = {
[0] = DEFINE_RES_MEM(S3C24XX_PA_SDI, S3C24XX_SZ_SDI),
[1] = DEFINE_RES_IRQ(IRQ_SDI),
};
+static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
+ /* This is currently here to avoid a number of if (host->pdata)
+ * checks. Any zero fields to ensure reasonable defaults are picked. */
+ .no_wprotect = 1,
+ .no_detect = 1,
+ .set_power = s3c24xx_mci_def_set_power,
+};
+
struct platform_device s3c_device_sdi = {
.name = "s3c2410-sdi",
.id = -1,
.num_resources = ARRAY_SIZE(s3c_sdi_resource),
.resource = s3c_sdi_resource,
+ .dev.platform_data = &s3cmci_def_pdata,
};
void __init s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata)
@@ -1038,6 +1069,8 @@ struct platform_device s3c_device_usb_hsudc = {
void __init s3c24xx_hsudc_set_platdata(struct s3c24xx_hsudc_platdata *pd)
{
s3c_set_platdata(pd, sizeof(*pd), &s3c_device_usb_hsudc);
+ pd->phy_init = s3c_hsudc_init_phy;
+ pd->phy_uninit = s3c_hsudc_uninit_phy;
}
#endif /* CONFIG_PLAT_S3C24XX */
diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/mach-s3c/devs.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/devs.h
rename to arch/arm/mach-s3c/devs.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/dma.h b/arch/arm/mach-s3c/dma-s3c24xx.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/include/mach/dma.h
rename to arch/arm/mach-s3c/dma-s3c24xx.h
diff --git a/arch/arm/mach-s3c64xx/include/mach/dma.h b/arch/arm/mach-s3c/dma-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/dma.h
rename to arch/arm/mach-s3c/dma-s3c64xx.h
diff --git a/arch/arm/mach-s3c/dma.h b/arch/arm/mach-s3c/dma.h
new file mode 100644
index 0000000..59a4578
--- /dev/null
+++ b/arch/arm/mach-s3c/dma.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "dma-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "dma-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/fb-core.h b/arch/arm/mach-s3c/fb-core-s3c24xx.h
similarity index 78%
rename from arch/arm/mach-s3c24xx/fb-core.h
rename to arch/arm/mach-s3c/fb-core-s3c24xx.h
index 1821e82..0e07f3b 100644
--- a/arch/arm/mach-s3c24xx/fb-core.h
+++ b/arch/arm/mach-s3c/fb-core-s3c24xx.h
@@ -5,8 +5,8 @@
*
* Samsung framebuffer driver core functions
*/
-#ifndef __ASM_PLAT_FB_CORE_H
-#define __ASM_PLAT_FB_CORE_H __FILE__
+#ifndef __ASM_PLAT_FB_CORE_S3C24XX_H
+#define __ASM_PLAT_FB_CORE_S3C24XX_H __FILE__
/*
* These functions are only for use with the core support code, such as
@@ -21,4 +21,4 @@ static inline void s3c_fb_setname(char *name)
#endif
}
-#endif /* __ASM_PLAT_FB_CORE_H */
+#endif /* __ASM_PLAT_FB_CORE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/mach-s3c/fb.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/fb.h
rename to arch/arm/mach-s3c/fb.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h b/arch/arm/mach-s3c/gpio-cfg-helpers.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
rename to arch/arm/mach-s3c/gpio-cfg-helpers.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/mach-s3c/gpio-cfg.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/gpio-cfg.h
rename to arch/arm/mach-s3c/gpio-cfg.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-core.h b/arch/arm/mach-s3c/gpio-core.h
similarity index 98%
rename from arch/arm/plat-samsung/include/plat/gpio-core.h
rename to arch/arm/mach-s3c/gpio-core.h
index c0bfceb..b361c8c 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-core.h
+++ b/arch/arm/mach-s3c/gpio-core.h
@@ -11,7 +11,7 @@
#define __PLAT_SAMSUNG_GPIO_CORE_H
/* Bring in machine-local definitions, especially S3C_GPIO_END */
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
#include <linux/gpio/driver.h>
#define GPIOCON_OFF (0x00)
diff --git a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung-s3c24xx.h
similarity index 98%
rename from arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h
rename to arch/arm/mach-s3c/gpio-samsung-s3c24xx.h
index 2ad22b2..c29fdc9 100644
--- a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h
+++ b/arch/arm/mach-s3c/gpio-samsung-s3c24xx.h
@@ -14,6 +14,8 @@
#ifndef GPIO_SAMSUNG_S3C24XX_H
#define GPIO_SAMSUNG_S3C24XX_H
+#include "map.h"
+
/*
* GPIO sizes for various SoCs:
*
diff --git a/arch/arm/mach-s3c64xx/include/mach/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/gpio-samsung.h
rename to arch/arm/mach-s3c/gpio-samsung-s3c64xx.h
diff --git a/arch/arm/plat-samsung/gpio-samsung.c b/arch/arm/mach-s3c/gpio-samsung.c
similarity index 98%
rename from arch/arm/plat-samsung/gpio-samsung.c
rename to arch/arm/mach-s3c/gpio-samsung.c
index 8955fd6..76ef415 100644
--- a/arch/arm/plat-samsung/gpio-samsung.c
+++ b/arch/arm/mach-s3c/gpio-samsung.c
@@ -27,15 +27,15 @@
#include <asm/irq.h>
#include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "pm.h"
int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
unsigned int off, samsung_gpio_pull_t pull)
diff --git a/arch/arm/mach-s3c/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung.h
new file mode 100644
index 0000000..02f6f4a
--- /dev/null
+++ b/arch/arm/mach-s3c/gpio-samsung.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "gpio-samsung-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "gpio-samsung-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/gta02.h b/arch/arm/mach-s3c/gta02.h
similarity index 94%
rename from arch/arm/mach-s3c24xx/gta02.h
rename to arch/arm/mach-s3c/gta02.h
index d5610ba..043ae38 100644
--- a/arch/arm/mach-s3c24xx/gta02.h
+++ b/arch/arm/mach-s3c/gta02.h
@@ -6,7 +6,7 @@
#ifndef __MACH_S3C24XX_GTA02_H
#define __MACH_S3C24XX_GTA02_H __FILE__
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
#define GTA02_GPIO_AUX_LED S3C2410_GPB(2)
#define GTA02_GPIO_USB_PULLUP S3C2410_GPB(9)
diff --git a/arch/arm/mach-s3c24xx/h1940-bluetooth.c b/arch/arm/mach-s3c/h1940-bluetooth.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/h1940-bluetooth.c
rename to arch/arm/mach-s3c/h1940-bluetooth.c
index 186b532..59edcf8 100644
--- a/arch/arm/mach-s3c24xx/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c/h1940-bluetooth.c
@@ -13,10 +13,9 @@
#include <linux/gpio.h>
#include <linux/rfkill.h>
-#include <plat/gpio-cfg.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include "h1940.h"
diff --git a/arch/arm/mach-s3c24xx/h1940.h b/arch/arm/mach-s3c/h1940.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/h1940.h
rename to arch/arm/mach-s3c/h1940.h
diff --git a/arch/arm/mach-s3c/hardware-s3c24xx.h b/arch/arm/mach-s3c/hardware-s3c24xx.h
new file mode 100644
index 0000000..33b3746
--- /dev/null
+++ b/arch/arm/mach-s3c/hardware-s3c24xx.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - hardware
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_S3C24XX_H
+#define __ASM_ARCH_HARDWARE_S3C24XX_H
+
+extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
+
+#endif /* __ASM_ARCH_HARDWARE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/iic-core.h b/arch/arm/mach-s3c/iic-core.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/iic-core.h
rename to arch/arm/mach-s3c/iic-core.h
diff --git a/arch/arm/mach-s3c/include/mach/io-s3c24xx.h b/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
new file mode 100644
index 0000000..738b775
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-s3c2410/include/mach/io.h
+ * from arch/arm/mach-rpc/include/mach/io.h
+ *
+ * Copyright (C) 1997 Russell King
+ * (C) 2003 Simtec Electronics
+*/
+
+#ifndef __ASM_ARM_ARCH_IO_S3C24XX_H
+#define __ASM_ARM_ARCH_IO_S3C24XX_H
+
+#include <mach/map-base.h>
+
+/*
+ * ISA style IO, for each machine to sort out mappings for,
+ * if it implements it. We reserve two 16M regions for ISA,
+ * so the PC/104 can use separate addresses for 8-bit and
+ * 16-bit port I/O.
+ */
+#define PCIO_BASE S3C_ADDR(0x02000000)
+#define IO_SPACE_LIMIT 0x00ffffff
+#define S3C24XX_VA_ISA_WORD (PCIO_BASE)
+#define S3C24XX_VA_ISA_BYTE (PCIO_BASE + 0x01000000)
+
+#ifdef CONFIG_ISA
+
+#define inb(p) readb(S3C24XX_VA_ISA_BYTE + (p))
+#define inw(p) readw(S3C24XX_VA_ISA_WORD + (p))
+#define inl(p) readl(S3C24XX_VA_ISA_WORD + (p))
+
+#define outb(v,p) writeb((v), S3C24XX_VA_ISA_BYTE + (p))
+#define outw(v,p) writew((v), S3C24XX_VA_ISA_WORD + (p))
+#define outl(v,p) writel((v), S3C24XX_VA_ISA_WORD + (p))
+
+#define insb(p,d,l) readsb(S3C24XX_VA_ISA_BYTE + (p),d,l)
+#define insw(p,d,l) readsw(S3C24XX_VA_ISA_WORD + (p),d,l)
+#define insl(p,d,l) readsl(S3C24XX_VA_ISA_WORD + (p),d,l)
+
+#define outsb(p,d,l) writesb(S3C24XX_VA_ISA_BYTE + (p),d,l)
+#define outsw(p,d,l) writesw(S3C24XX_VA_ISA_WORD + (p),d,l)
+#define outsl(p,d,l) writesl(S3C24XX_VA_ISA_WORD + (p),d,l)
+
+#else
+
+#define __io(x) (PCIO_BASE + (x))
+
+#endif
+
+#endif
diff --git a/arch/arm/mach-s3c/include/mach/io.h b/arch/arm/mach-s3c/include/mach/io.h
new file mode 100644
index 0000000..30a0135
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/io.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "io-s3c24xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/include/mach/irqs.h
rename to arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h
diff --git a/arch/arm/mach-s3c64xx/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/irqs.h
rename to arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h
diff --git a/arch/arm/mach-s3c/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs.h
new file mode 100644
index 0000000..0bff1c1
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/irqs.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "irqs-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "irqs-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/map-base.h b/arch/arm/mach-s3c/include/mach/map-base.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/map-base.h
rename to arch/arm/mach-s3c/include/mach/map-base.h
diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/mach-s3c/init.c
similarity index 98%
rename from arch/arm/plat-samsung/init.c
rename to arch/arm/mach-s3c/init.c
index e9acf02e..9d92f03 100644
--- a/arch/arm/plat-samsung/init.c
+++ b/arch/arm/mach-s3c/init.c
@@ -23,8 +23,8 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
+#include "cpu.h"
+#include "devs.h"
static struct cpu_table *cpu;
diff --git a/arch/arm/mach-s3c24xx/iotiming-s3c2410.c b/arch/arm/mach-s3c/iotiming-s3c2410.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/iotiming-s3c2410.c
rename to arch/arm/mach-s3c/iotiming-s3c2410.c
index 9f90aaf..28d9f47 100644
--- a/arch/arm/mach-s3c24xx/iotiming-s3c2410.c
+++ b/arch/arm/mach-s3c/iotiming-s3c2410.c
@@ -14,12 +14,12 @@
#include <linux/io.h>
#include <linux/slab.h>
-#include <mach/map.h>
-#include <mach/regs-clock.h>
+#include "map.h"
+#include "regs-clock.h"
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
#define print_ns(x) ((x) / 10), ((x) % 10)
@@ -129,7 +129,7 @@ static unsigned int calc_0124(unsigned int cyc, unsigned long hclk_tns,
return 0;
}
-int calc_tacp(unsigned int cyc, unsigned long hclk, unsigned long *v)
+static int calc_tacp(unsigned int cyc, unsigned long hclk, unsigned long *v)
{
/* Currently no support for Tacp calculations. */
return 0;
@@ -288,8 +288,8 @@ static unsigned int get_0124(unsigned long hclk_tns,
* Given the BANKCON setting in @bt and the current frequency settings
* in @cfg, update the cycle timing information.
*/
-void s3c2410_iotiming_getbank(struct s3c_cpufreq_config *cfg,
- struct s3c2410_iobank_timing *bt)
+static void s3c2410_iotiming_getbank(struct s3c_cpufreq_config *cfg,
+ struct s3c2410_iobank_timing *bt)
{
unsigned long bankcon = bt->bankcon;
unsigned long hclk = cfg->freq.hclk_tns;
diff --git a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c b/arch/arm/mach-s3c/iotiming-s3c2412.c
similarity index 98%
rename from arch/arm/mach-s3c24xx/iotiming-s3c2412.c
rename to arch/arm/mach-s3c/iotiming-s3c2412.c
index 59356d1..003f89c 100644
--- a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c
+++ b/arch/arm/mach-s3c/iotiming-s3c2412.c
@@ -23,10 +23,10 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include <mach/s3c2412.h>
+#include "s3c2412.h"
#define print_ns(x) ((x) / 10), ((x) % 10)
diff --git a/arch/arm/mach-s3c24xx/irq-pm.c b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
similarity index 92%
rename from arch/arm/mach-s3c24xx/irq-pm.c
rename to arch/arm/mach-s3c/irq-pm-s3c24xx.c
index e0131b1..4d5e283 100644
--- a/arch/arm/mach-s3c24xx/irq-pm.c
+++ b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
@@ -13,14 +13,14 @@
#include <linux/syscore_ops.h>
#include <linux/io.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
+#include "cpu.h"
+#include "pm.h"
+#include <mach/map-base.h>
+#include "map-s3c.h"
-#include <mach/regs-irq.h>
-#include <mach/regs-gpio.h>
-#include <mach/pm-core.h>
+#include "regs-irq.h"
+#include "regs-gpio.h"
+#include "pm-core.h"
#include <asm/irq.h>
diff --git a/arch/arm/mach-s3c64xx/irq-pm.c b/arch/arm/mach-s3c/irq-pm-s3c64xx.c
similarity index 96%
rename from arch/arm/mach-s3c64xx/irq-pm.c
rename to arch/arm/mach-s3c/irq-pm-s3c64xx.c
index 31b2211..4a1e935 100644
--- a/arch/arm/mach-s3c64xx/irq-pm.c
+++ b/arch/arm/mach-s3c/irq-pm-s3c64xx.c
@@ -20,11 +20,11 @@
#include <linux/io.h>
#include <linux/of.h>
-#include <mach/map.h>
+#include "map.h"
-#include <mach/regs-gpio.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "regs-gpio.h"
+#include "cpu.h"
+#include "pm.h"
/* We handled all the IRQ types in this code, to save having to make several
* small files to handle each different type separately. Having the EINT_GRP
diff --git a/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c b/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c
new file mode 100644
index 0000000..84cf863
--- /dev/null
+++ b/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/stddef.h>
+#include <linux/export.h>
+#include <linux/spi/s3c24xx-fiq.h>
+
+EXPORT_SYMBOL(s3c24xx_spi_fiq_rx);
+EXPORT_SYMBOL(s3c24xx_spi_fiq_txrx);
+EXPORT_SYMBOL(s3c24xx_spi_fiq_tx);
diff --git a/drivers/spi/spi-s3c24xx-fiq.S b/arch/arm/mach-s3c/irq-s3c24xx-fiq.S
similarity index 94%
rename from drivers/spi/spi-s3c24xx-fiq.S
rename to arch/arm/mach-s3c/irq-s3c24xx-fiq.S
index e95d628..b54cbd0 100644
--- a/drivers/spi/spi-s3c24xx-fiq.S
+++ b/arch/arm/mach-s3c/irq-s3c24xx-fiq.S
@@ -10,11 +10,13 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <mach/map.h>
-#include <mach/regs-irq.h>
-#include <plat/regs-spi.h>
+#include "map.h"
+#include "regs-irq.h"
-#include "spi-s3c24xx-fiq.h"
+#include <linux/spi/s3c24xx-fiq.h>
+
+#define S3C2410_SPTDAT (0x10)
+#define S3C2410_SPRDAT (0x14)
.text
diff --git a/drivers/irqchip/irq-s3c24xx.c b/arch/arm/mach-s3c/irq-s3c24xx.c
similarity index 98%
rename from drivers/irqchip/irq-s3c24xx.c
rename to arch/arm/mach-s3c/irq-s3c24xx.c
index d2031fe..79b5f19 100644
--- a/drivers/irqchip/irq-s3c24xx.c
+++ b/arch/arm/mach-s3c/irq-s3c24xx.c
@@ -25,12 +25,13 @@
#include <asm/exception.h>
#include <asm/mach/irq.h>
-#include <mach/regs-irq.h>
-#include <mach/regs-gpio.h>
+#include <mach/irqs.h>
+#include "regs-irq.h"
+#include "regs-gpio.h"
-#include <plat/cpu.h>
-#include <plat/regs-irqtype.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "regs-irqtype.h"
+#include "pm.h"
#define S3C_IRQTYPE_NONE 0
#define S3C_IRQTYPE_EINT 1
@@ -375,14 +376,17 @@ asmlinkage void __exception_irq_entry s3c24xx_handle_irq(struct pt_regs *regs)
/**
* s3c24xx_set_fiq - set the FIQ routing
* @irq: IRQ number to route to FIQ on processor.
+ * @ack_ptr: pointer to a location for storing the bit mask
* @on: Whether to route @irq to the FIQ, or to remove the FIQ routing.
*
* Change the state of the IRQ to FIQ routing depending on @irq and @on. If
* @on is true, the @irq is checked to see if it can be routed and the
* interrupt controller updated to route the IRQ. If @on is false, the FIQ
* routing is cleared, regardless of which @irq is specified.
+ *
+ * returns the mask value for the register.
*/
-int s3c24xx_set_fiq(unsigned int irq, bool on)
+int s3c24xx_set_fiq(unsigned int irq, u32 *ack_ptr, bool on)
{
u32 intmod;
unsigned offs;
@@ -390,15 +394,18 @@ int s3c24xx_set_fiq(unsigned int irq, bool on)
if (on) {
offs = irq - FIQ_START;
if (offs > 31)
- return -EINVAL;
+ return 0;
intmod = 1 << offs;
} else {
intmod = 0;
}
+ if (ack_ptr)
+ *ack_ptr = intmod;
writel_relaxed(intmod, S3C2410_INTMOD);
- return 0;
+
+ return intmod;
}
EXPORT_SYMBOL_GPL(s3c24xx_set_fiq);
diff --git a/arch/arm/mach-s3c64xx/irq-uart.h b/arch/arm/mach-s3c/irq-uart-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/irq-uart.h
rename to arch/arm/mach-s3c/irq-uart-s3c64xx.h
diff --git a/arch/arm/plat-samsung/include/plat/keypad.h b/arch/arm/mach-s3c/keypad.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/keypad.h
rename to arch/arm/mach-s3c/keypad.h
diff --git a/arch/arm/mach-s3c24xx/mach-amlm5900.c b/arch/arm/mach-s3c/mach-amlm5900.c
similarity index 83%
rename from arch/arm/mach-s3c24xx/mach-amlm5900.c
rename to arch/arm/mach-s3c/mach-amlm5900.c
index 9a9daf5..94c4512 100644
--- a/arch/arm/mach-s3c24xx/mach-amlm5900.c
+++ b/arch/arm/mach-s3c/mach-amlm5900.c
@@ -13,6 +13,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio/machine.h>
#include <linux/gpio.h>
#include <linux/device.h>
#include <linux/platform_device.h>
@@ -26,28 +27,24 @@
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
-#include <mach/regs-lcd.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/gpio-cfg.h>
+#include "devs.h"
+#include "cpu.h"
+#include "gpio-cfg.h"
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/map.h>
#include <linux/mtd/physmap.h>
-#include <plat/samsung-time.h>
-
-#include "common.h"
+#include "s3c24xx.h"
static struct resource amlm5900_nor_resource =
DEFINE_RES_MEM(0x00000000, SZ_16M);
@@ -124,6 +121,19 @@ static struct s3c2410_uartcfg amlm5900_uartcfgs[] = {
}
};
+static struct gpiod_lookup_table amlm5900_mmc_gpio_table = {
+ .dev_id = "s3c2410-sdi",
+ .table = {
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
static struct platform_device *amlm5900_devices[] __initdata = {
#ifdef CONFIG_FB_S3C2410
@@ -143,13 +153,13 @@ static void __init amlm5900_map_io(void)
{
s3c24xx_init_io(amlm5900_iodesc, ARRAY_SIZE(amlm5900_iodesc));
s3c24xx_init_uarts(amlm5900_uartcfgs, ARRAY_SIZE(amlm5900_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init amlm5900_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
#ifdef CONFIG_FB_S3C2410
@@ -180,13 +190,17 @@ static struct s3c2410fb_mach_info __initdata amlm5900_fb_info = {
.gpccon = 0xaaaaaaaa,
.gpccon_mask = 0xffffffff,
+ .gpccon_reg = S3C2410_GPCCON,
.gpcup = 0x0000ffff,
.gpcup_mask = 0xffffffff,
+ .gpcup_reg = S3C2410_GPCUP,
.gpdcon = 0xaaaaaaaa,
.gpdcon_mask = 0xffffffff,
+ .gpdcon_reg = S3C2410_GPDCON,
.gpdup = 0x0000ffff,
.gpdup_mask = 0xffffffff,
+ .gpdup_reg = S3C2410_GPDUP,
};
#endif
@@ -219,6 +233,7 @@ static void __init amlm5900_init(void)
s3c24xx_fb_set_platdata(&amlm5900_fb_info);
#endif
s3c_i2c0_set_platdata(NULL);
+ gpiod_add_lookup_table(&amlm5900_mmc_gpio_table);
platform_add_devices(amlm5900_devices, ARRAY_SIZE(amlm5900_devices));
}
diff --git a/arch/arm/mach-s3c24xx/mach-anubis.c b/arch/arm/mach-s3c/mach-anubis.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/mach-anubis.c
rename to arch/arm/mach-s3c/mach-anubis.c
index 2832624..90e3fd9 100644
--- a/arch/arm/mach-s3c24xx/mach-anubis.c
+++ b/arch/arm/mach-s3c/mach-anubis.c
@@ -24,13 +24,11 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
@@ -41,13 +39,12 @@
#include <net/ax88796.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
#include <linux/platform_data/asoc-s3c24xx_simtec.h>
-#include <plat/samsung-time.h>
#include "anubis.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "simtec.h"
#define COPYRIGHT ", Copyright 2005-2009 Simtec Electronics"
@@ -384,7 +381,7 @@ static void __init anubis_map_io(void)
{
s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc));
s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
/* check for the newer revision boards with large page nand */
@@ -403,7 +400,7 @@ static void __init anubis_map_io(void)
static void __init anubis_init_time(void)
{
s3c2440_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init anubis_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-anw6410.c b/arch/arm/mach-s3c/mach-anw6410.c
similarity index 93%
rename from arch/arm/mach-s3c64xx/mach-anw6410.c
rename to arch/arm/mach-s3c/mach-anw6410.c
index 0d3d5be..825714e 100644
--- a/arch/arm/mach-s3c64xx/mach-anw6410.c
+++ b/arch/arm/mach-s3c/mach-anw6410.c
@@ -30,24 +30,22 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
+#include "fb.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
#include <mach/irqs.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-#include <plat/samsung-time.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include "common.h"
-#include "regs-modem.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
/* DM9000 */
#define ANW6410_PA_DM9000 (0x18000000)
@@ -204,7 +202,7 @@ static void __init anw6410_map_io(void)
s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc));
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
anw6410_lcd_mode_set();
}
@@ -228,6 +226,5 @@ MACHINE_START(ANW6410, "A&W6410")
.init_irq = s3c6410_init_irq,
.map_io = anw6410_map_io,
.init_machine = anw6410_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-at2440evb.c b/arch/arm/mach-s3c/mach-at2440evb.c
similarity index 87%
rename from arch/arm/mach-s3c24xx/mach-at2440evb.c
rename to arch/arm/mach-s3c/mach-at2440evb.c
index 04dedeb..5fa49d4 100644
--- a/arch/arm/mach-s3c24xx/mach-at2440evb.c
+++ b/arch/arm/mach-s3c/mach-at2440evb.c
@@ -24,14 +24,12 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
@@ -40,12 +38,11 @@
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
#include <linux/platform_data/mmc-s3cmci.h>
-#include <plat/samsung-time.h>
-#include "common.h"
+#include "s3c24xx.h"
static struct map_desc at2440evb_iodesc[] __initdata = {
/* Nothing here */
@@ -136,18 +133,26 @@ static struct platform_device at2440evb_device_eth = {
};
static struct s3c24xx_mci_pdata at2440evb_mci_pdata __initdata = {
- /* Intentionally left blank */
+ .set_power = s3c24xx_mci_def_set_power,
};
static struct gpiod_lookup_table at2440evb_mci_gpio_table = {
.dev_id = "s3c2410-sdi",
.table = {
/* Card detect S3C2410_GPG(10) */
- GPIO_LOOKUP("GPG", 10, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOG", 10, "cd", GPIO_ACTIVE_LOW),
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
{ },
},
};
+
/* 7" LCD panel */
static struct s3c2410fb_display at2440evb_lcd_cfg __initdata = {
@@ -197,13 +202,13 @@ static void __init at2440evb_map_io(void)
{
s3c24xx_init_io(at2440evb_iodesc, ARRAY_SIZE(at2440evb_iodesc));
s3c24xx_init_uarts(at2440evb_uartcfgs, ARRAY_SIZE(at2440evb_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init at2440evb_init_time(void)
{
s3c2440_init_clocks(16934400);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init at2440evb_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-bast.c b/arch/arm/mach-s3c/mach-bast.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/mach-bast.c
rename to arch/arm/mach-s3c/mach-bast.c
index 6465eab..328f5d9 100644
--- a/arch/arm/mach-s3c24xx/mach-bast.c
+++ b/arch/arm/mach-s3c/mach-bast.c
@@ -40,20 +40,17 @@
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/fb-s3c2410.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "devs.h"
+#include "gpio-cfg.h"
#include "bast.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "simtec.h"
#define COPYRIGHT ", Copyright 2004-2008 Simtec Electronics"
@@ -550,13 +547,13 @@ static void __init bast_map_io(void)
s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init bast_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init bast_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
similarity index 98%
rename from arch/arm/mach-s3c64xx/mach-crag6410-module.c
rename to arch/arm/mach-s3c/mach-crag6410-module.c
index 34f1baa..407ad49 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -27,7 +27,7 @@
#include <linux/platform_data/spi-s3c64xx.h>
-#include <plat/cpu.h>
+#include "cpu.h"
#include <mach/irqs.h>
#include "crag6410.h"
@@ -378,8 +378,7 @@ static const struct {
.i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c) },
};
-static int wlf_gf_module_probe(struct i2c_client *i2c,
- const struct i2c_device_id *i2c_id)
+static int wlf_gf_module_probe(struct i2c_client *i2c)
{
int ret, i, j, id, rev;
@@ -432,7 +431,7 @@ static struct i2c_driver wlf_gf_module_driver = {
.driver = {
.name = "wlf-gf-module"
},
- .probe = wlf_gf_module_probe,
+ .probe_new = wlf_gf_module_probe,
.id_table = wlf_gf_module_id,
};
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c/mach-crag6410.c
similarity index 97%
rename from arch/arm/mach-s3c64xx/mach-crag6410.c
rename to arch/arm/mach-s3c/mach-crag6410.c
index da96542..4a12c75 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c/mach-crag6410.c
@@ -44,30 +44,28 @@
#include <asm/mach-types.h>
#include <video/samsung_fimd.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <mach/irqs.h>
-#include <plat/fb.h>
-#include <plat/sdhci.h>
-#include <plat/gpio-cfg.h>
+#include "fb.h"
+#include "sdhci.h"
+#include "gpio-cfg.h"
#include <linux/platform_data/spi-s3c64xx.h>
-#include <plat/keypad.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc.h>
+#include "keypad.h"
+#include "devs.h"
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-adc.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "pm.h"
-#include "common.h"
+#include "s3c64xx.h"
#include "crag6410.h"
-#include "regs-gpio-memport.h"
-#include "regs-modem.h"
-#include "regs-sys.h"
+#include "regs-gpio-memport-s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
/* serial port setup */
@@ -750,7 +748,7 @@ static void __init crag6410_map_io(void)
s3c64xx_init_io(NULL, 0);
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(crag6410_uartcfgs, ARRAY_SIZE(crag6410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
/* LCD type and Bypass set by bootloader */
}
@@ -877,6 +875,5 @@ MACHINE_START(WLF_CRAGG_6410, "Wolfson Cragganmore 6410")
.init_irq = s3c6410_init_irq,
.map_io = crag6410_map_io,
.init_machine = crag6410_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-gta02.c b/arch/arm/mach-s3c/mach-gta02.c
similarity index 92%
rename from arch/arm/mach-s3c24xx/mach-gta02.c
rename to arch/arm/mach-s3c/mach-gta02.c
index 7327481..3c75c7d 100644
--- a/arch/arm/mach-s3c24xx/mach-gta02.c
+++ b/arch/arm/mach-s3c/mach-gta02.c
@@ -57,20 +57,18 @@
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <linux/platform_data/usb-ohci-s3c2410.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/fb-s3c2410.h>
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-irq.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "regs-irq.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "gpio-cfg.h"
+#include "pm.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "gta02.h"
static struct pcf50633 *gta02_pcf;
@@ -489,11 +487,25 @@ static struct platform_device gta02_audio = {
.id = -1,
};
+static struct gpiod_lookup_table gta02_mmc_gpio_table = {
+ .dev_id = "s3c2410-sdi",
+ .table = {
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
static void __init gta02_map_io(void)
{
s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc));
s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
@@ -540,7 +552,12 @@ static void __init gta02_machine_init(void)
i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs));
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+
gpiod_add_lookup_table(>a02_audio_gpio_table);
+ gpiod_add_lookup_table(>a02_mmc_gpio_table);
platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
pm_power_off = gta02_poweroff;
@@ -550,7 +567,7 @@ static void __init gta02_machine_init(void)
static void __init gta02_init_time(void)
{
s3c2442_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
MACHINE_START(NEO1973_GTA02, "GTA02")
diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c/mach-h1940.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/mach-h1940.c
rename to arch/arm/mach-s3c/mach-h1940.c
index ecb8402..53d51aa 100644
--- a/arch/arm/mach-s3c24xx/mach-h1940.c
+++ b/arch/arm/mach-s3c/mach-h1940.c
@@ -47,20 +47,19 @@
#include <sound/uda1380.h>
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/fb-s3c2410.h>
+#include "map.h"
+#include "hardware-s3c24xx.h"
+#include "regs-clock.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "gpio-cfg.h"
+#include "pm.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "h1940.h"
#define H1940_LATCH ((void __force __iomem *)0xF8000000)
@@ -180,9 +179,9 @@ static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = {
.cfg_gpio = s3c24xx_ts_cfg_gpio,
};
-/**
+/*
* Set lcd on or off
- **/
+ */
static struct s3c2410fb_display h1940_lcd __initdata = {
.lcdcon5= S3C2410_LCDCON5_FRM565 | \
S3C2410_LCDCON5_INVVLINE | \
@@ -211,12 +210,16 @@ static struct s3c2410fb_mach_info h1940_fb_info __initdata = {
.lpcsel = 0x02,
.gpccon = 0xaa940659,
.gpccon_mask = 0xffffc0f0,
+ .gpccon_reg = S3C2410_GPCCON,
.gpcup = 0x0000ffff,
.gpcup_mask = 0xffffffff,
+ .gpcup_reg = S3C2410_GPCUP,
.gpdcon = 0xaa84aaa0,
.gpdcon_mask = 0xffffffff,
+ .gpdcon_reg = S3C2410_GPDCON,
.gpdup = 0x0000faff,
.gpdup_mask = 0xffffffff,
+ .gpdup_reg = S3C2410_GPDUP,
};
static int power_supply_init(struct device *dev)
@@ -446,6 +449,8 @@ static struct platform_device h1940_device_bluetooth = {
static void h1940_set_mmc_power(unsigned char power_mode, unsigned short vdd)
{
+ s3c24xx_mci_def_set_power(power_mode, vdd);
+
switch (power_mode) {
case MMC_POWER_OFF:
gpio_set_value(H1940_LATCH_SD_POWER, 0);
@@ -468,9 +473,16 @@ static struct gpiod_lookup_table h1940_mmc_gpio_table = {
.dev_id = "s3c2410-sdi",
.table = {
/* Card detect S3C2410_GPF(5) */
- GPIO_LOOKUP("GPF", 5, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOF", 5, "cd", GPIO_ACTIVE_LOW),
/* Write protect S3C2410_GPH(8) */
- GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_LOW),
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
{ },
},
};
@@ -674,7 +686,7 @@ static void __init h1940_map_io(void)
{
s3c24xx_init_io(h1940_iodesc, ARRAY_SIZE(h1940_iodesc));
s3c24xx_init_uarts(h1940_uartcfgs, ARRAY_SIZE(h1940_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
/* setup PM */
@@ -691,7 +703,7 @@ static void __init h1940_map_io(void)
static void __init h1940_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
/* H1940 and RX3715 need to reserve this for suspend */
@@ -708,6 +720,9 @@ static void __init h1940_init(void)
s3c24xx_fb_set_platdata(&h1940_fb_info);
gpiod_add_lookup_table(&h1940_mmc_gpio_table);
gpiod_add_lookup_table(&h1940_audio_gpio_table);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
s3c24xx_mci_set_platdata(&h1940_mmc_cfg);
s3c24xx_udc_set_platdata(&h1940_udc_cfg);
s3c24xx_ts_set_platdata(&h1940_ts_cfg);
diff --git a/arch/arm/mach-s3c64xx/mach-hmt.c b/arch/arm/mach-s3c/mach-hmt.c
similarity index 94%
rename from arch/arm/mach-s3c64xx/mach-hmt.c
rename to arch/arm/mach-s3c/mach-hmt.c
index 0d9acaf..b287e99 100644
--- a/arch/arm/mach-s3c64xx/mach-hmt.c
+++ b/arch/arm/mach-s3c/mach-hmt.c
@@ -25,23 +25,21 @@
#include <asm/mach/irq.h>
#include <video/samsung_fimd.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
#include <mach/irqs.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <plat/fb.h>
+#include "gpio-samsung.h"
+#include "fb.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
+#include "s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT
#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
@@ -251,7 +249,7 @@ static void __init hmt_map_io(void)
s3c64xx_init_io(hmt_iodesc, ARRAY_SIZE(hmt_iodesc));
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(hmt_uartcfgs, ARRAY_SIZE(hmt_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
}
static void __init hmt_machine_init(void)
@@ -280,6 +278,5 @@ MACHINE_START(HMT, "Airgoo-HMT")
.init_irq = s3c6410_init_irq,
.map_io = hmt_map_io,
.init_machine = hmt_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-jive.c b/arch/arm/mach-s3c/mach-jive.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/mach-jive.c
rename to arch/arm/mach-s3c/mach-jive.c
index 8233dcf..2a29c3e 100644
--- a/arch/arm/mach-s3c24xx/mach-jive.c
+++ b/arch/arm/mach-s3c/mach-jive.c
@@ -31,10 +31,10 @@
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/fb.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include <linux/platform_data/fb-s3c2410.h>
+#include "gpio-samsung.h"
#include <asm/mach-types.h>
@@ -43,14 +43,13 @@
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
#include <linux/platform_data/usb-s3c2410_udc.h>
-#include <plat/samsung-time.h>
-#include "common.h"
+#include "s3c24xx.h"
#include "s3c2412-power.h"
static struct map_desc jive_iodesc[] __initdata = {
@@ -321,6 +320,7 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
* data. */
.gpcup = (0xf << 1) | (0x3f << 10),
+ .gpcup_reg = S3C2410_GPCUP,
.gpccon = (S3C2410_GPC1_VCLK | S3C2410_GPC2_VLINE |
S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
@@ -334,8 +334,12 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
+ .gpccon_reg = S3C2410_GPCCON,
+
.gpdup = (0x3f << 2) | (0x3f << 10),
+ .gpdup_reg = S3C2410_GPDUP,
+
.gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 |
S3C2410_GPD4_VD12 | S3C2410_GPD5_VD13 |
S3C2410_GPD6_VD14 | S3C2410_GPD7_VD15 |
@@ -349,6 +353,8 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+
+ .gpdcon_reg = S3C2410_GPDCON,
};
/* ILI9320 support. */
@@ -523,13 +529,13 @@ static void __init jive_map_io(void)
{
s3c24xx_init_io(jive_iodesc, ARRAY_SIZE(jive_iodesc));
s3c24xx_init_uarts(jive_uartcfgs, ARRAY_SIZE(jive_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init jive_init_time(void)
{
s3c2412_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void jive_power_off(void)
diff --git a/arch/arm/mach-s3c24xx/mach-mini2440.c b/arch/arm/mach-s3c/mach-mini2440.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/mach-mini2440.c
rename to arch/arm/mach-s3c/mach-mini2440.c
index 057dcba..dc22ab83 100644
--- a/arch/arm/mach-s3c24xx/mach-mini2440.c
+++ b/arch/arm/mach-s3c/mach-mini2440.c
@@ -30,15 +30,13 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
#include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-lcd.h>
#include <mach/irqs.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/platform_data/mmc-s3cmci.h>
@@ -49,14 +47,13 @@
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
#include <sound/s3c24xx_uda134x.h>
-#include "common.h"
+#include "s3c24xx.h"
#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
@@ -215,6 +212,9 @@ static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
+ .gpccon_reg = S3C2410_GPCCON,
+ .gpcup_reg = S3C2410_GPCUP,
+
.gpdup = (0x3f << 2) | (0x3f << 10),
.gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 |
@@ -230,13 +230,16 @@ static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+
+ .gpdcon_reg = S3C2410_GPDCON,
+ .gpdup_reg = S3C2410_GPDUP,
};
/* MMC/SD */
static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
.wprotect_invert = 1,
- .set_power = NULL,
+ .set_power = s3c24xx_mci_def_set_power,
.ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34,
};
@@ -244,9 +247,16 @@ static struct gpiod_lookup_table mini2440_mmc_gpio_table = {
.dev_id = "s3c2410-sdi",
.table = {
/* Card detect S3C2410_GPG(8) */
- GPIO_LOOKUP("GPG", 8, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOG", 8, "cd", GPIO_ACTIVE_LOW),
/* Write protect S3C2410_GPH(8) */
- GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_HIGH),
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
{ },
},
};
@@ -587,13 +597,13 @@ static void __init mini2440_map_io(void)
{
s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init mini2440_init_time(void)
{
s3c2440_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
/*
@@ -716,6 +726,11 @@ static void __init mini2440_init(void)
s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
s3c_gpio_cfgpin(mini2440_buttons[i].gpio, S3C2410_GPIO_INPUT);
}
+
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+
if (features.lcd_index != -1) {
int li;
diff --git a/arch/arm/mach-s3c64xx/mach-mini6410.c b/arch/arm/mach-s3c/mach-mini6410.c
similarity index 95%
rename from arch/arm/mach-s3c64xx/mach-mini6410.c
rename to arch/arm/mach-s3c/mach-mini6410.c
index 6fbb578..741fa1f 100644
--- a/arch/arm/mach-s3c64xx/mach-mini6410.c
+++ b/arch/arm/mach-s3c/mach-mini6410.c
@@ -23,27 +23,26 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/adc.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
+#include <linux/soc/samsung/s3c-adc.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/mmc-sdhci-s3c.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <mach/irqs.h>
#include <video/platform_lcd.h>
#include <video/samsung_fimd.h>
-#include <plat/samsung-time.h>
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT
#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
@@ -238,7 +237,7 @@ static void __init mini6410_map_io(void)
s3c64xx_init_io(NULL, 0);
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(mini6410_uartcfgs, ARRAY_SIZE(mini6410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
/* set the LCD type */
tmp = __raw_readl(S3C64XX_SPCON);
@@ -362,6 +361,5 @@ MACHINE_START(MINI6410, "MINI6410")
.init_irq = s3c6410_init_irq,
.map_io = mini6410_map_io,
.init_machine = mini6410_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-n30.c b/arch/arm/mach-s3c/mach-n30.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/mach-n30.c
rename to arch/arm/mach-s3c/mach-n30.c
index 998ccff..e40c1fc 100644
--- a/arch/arm/mach-s3c24xx/mach-n30.c
+++ b/arch/arm/mach-s3c/mach-n30.c
@@ -27,15 +27,15 @@
#include <linux/io.h>
#include <linux/mmc/host.h>
-#include <mach/hardware.h>
+#include "hardware-s3c24xx.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
@@ -43,14 +43,12 @@
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
+#include "cpu.h"
+#include "devs.h"
#include <linux/platform_data/mmc-s3cmci.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
-#include <plat/samsung-time.h>
-#include "common.h"
+#include "s3c24xx.h"
static struct map_desc n30_iodesc[] __initdata = {
/* nothing here yet */
@@ -368,6 +366,8 @@ static struct s3c2410fb_mach_info n30_fb_info __initdata = {
static void n30_sdi_set_power(unsigned char power_mode, unsigned short vdd)
{
+ s3c24xx_mci_def_set_power(power_mode, vdd);
+
switch (power_mode) {
case MMC_POWER_ON:
case MMC_POWER_UP:
@@ -389,10 +389,17 @@ static struct gpiod_lookup_table n30_mci_gpio_table = {
.dev_id = "s3c2410-sdi",
.table = {
/* Card detect S3C2410_GPF(1) */
- GPIO_LOOKUP("GPF", 1, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOF", 1, "cd", GPIO_ACTIVE_LOW),
/* Write protect S3C2410_GPG(10) */
- GPIO_LOOKUP("GPG", 10, "wp", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOG", 10, "wp", GPIO_ACTIVE_LOW),
{ },
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
},
};
@@ -572,13 +579,13 @@ static void __init n30_map_io(void)
s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc));
n30_hwinit();
s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init n30_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
/* GPB3 is the line that controls the pull-up for the USB D+ line */
@@ -600,6 +607,10 @@ static void __init n30_init(void)
S3C2410_MISCCR_USBSUSPND0 |
S3C2410_MISCCR_USBSUSPND1, 0x0);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+
if (machine_is_n30()) {
/* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
diff --git a/arch/arm/mach-s3c64xx/mach-ncp.c b/arch/arm/mach-s3c/mach-ncp.c
similarity index 87%
rename from arch/arm/mach-s3c64xx/mach-ncp.c
rename to arch/arm/mach-s3c/mach-ncp.c
index 13fea5c..1a45bed 100644
--- a/arch/arm/mach-s3c64xx/mach-ncp.c
+++ b/arch/arm/mach-s3c/mach-ncp.c
@@ -25,20 +25,18 @@
#include <asm/mach/irq.h>
#include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
+#include "fb.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
+#include "s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE
@@ -81,7 +79,7 @@ static void __init ncp_map_io(void)
s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc));
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
}
static void __init ncp_machine_init(void)
@@ -98,6 +96,5 @@ MACHINE_START(NCP, "NCP")
.init_irq = s3c6410_init_irq,
.map_io = ncp_map_io,
.init_machine = ncp_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-nexcoder.c b/arch/arm/mach-s3c/mach-nexcoder.c
similarity index 90%
rename from arch/arm/mach-s3c24xx/mach-nexcoder.c
rename to arch/arm/mach-s3c/mach-nexcoder.c
index c2f3475..2a454c9 100644
--- a/arch/arm/mach-s3c24xx/mach-nexcoder.c
+++ b/arch/arm/mach-s3c/mach-nexcoder.c
@@ -28,21 +28,19 @@
#include <asm/mach/irq.h>
#include <asm/setup.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
//#include <asm/debug-ll.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
+#include "s3c24xx.h"
static struct map_desc nexcoder_iodesc[] __initdata = {
/* nothing here yet */
@@ -131,7 +129,7 @@ static void __init nexcoder_map_io(void)
{
s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc));
s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
nexcoder_sensorboard_init();
}
@@ -139,12 +137,17 @@ static void __init nexcoder_map_io(void)
static void __init nexcoder_init_time(void)
{
s3c2440_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init nexcoder_init(void)
{
s3c_i2c0_set_platdata(NULL);
+
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+
platform_add_devices(nexcoder_devices, ARRAY_SIZE(nexcoder_devices));
};
diff --git a/arch/arm/mach-s3c24xx/mach-osiris-dvs.c b/arch/arm/mach-s3c/mach-osiris-dvs.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/mach-osiris-dvs.c
rename to arch/arm/mach-s3c/mach-osiris-dvs.c
index 5d819b6..2e283ae 100644
--- a/arch/arm/mach-s3c24xx/mach-osiris-dvs.c
+++ b/arch/arm/mach-s3c/mach-osiris-dvs.c
@@ -14,8 +14,8 @@
#include <linux/mfd/tps65010.h>
-#include <plat/cpu-freq.h>
-#include <mach/gpio-samsung.h>
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "gpio-samsung.h"
#define OSIRIS_GPIO_DVS S3C2410_GPB(5)
diff --git a/arch/arm/mach-s3c24xx/mach-osiris.c b/arch/arm/mach-s3c/mach-osiris.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/mach-osiris.c
rename to arch/arm/mach-s3c/mach-osiris.c
index 1574488..81744ca 100644
--- a/arch/arm/mach-s3c24xx/mach-osiris.c
+++ b/arch/arm/mach-s3c/mach-osiris.c
@@ -36,20 +36,17 @@
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "devs.h"
+#include "gpio-cfg.h"
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "osiris.h"
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
/* onboard perihperal map */
@@ -359,7 +356,7 @@ static void __init osiris_map_io(void)
s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc));
s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
/* check for the newer revision boards with large page nand */
@@ -384,7 +381,7 @@ static void __init osiris_map_io(void)
static void __init osiris_init_time(void)
{
s3c2440_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init osiris_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-otom.c b/arch/arm/mach-s3c/mach-otom.c
similarity index 88%
rename from arch/arm/mach-s3c24xx/mach-otom.c
rename to arch/arm/mach-s3c/mach-otom.c
index 4e24d89..460ee97 100644
--- a/arch/arm/mach-s3c24xx/mach-otom.c
+++ b/arch/arm/mach-s3c/mach-otom.c
@@ -22,14 +22,13 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "otom.h"
static struct map_desc otom11_iodesc[] __initdata = {
@@ -95,18 +94,22 @@ static void __init otom11_map_io(void)
{
s3c24xx_init_io(otom11_iodesc, ARRAY_SIZE(otom11_iodesc));
s3c24xx_init_uarts(otom11_uartcfgs, ARRAY_SIZE(otom11_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init otom11_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init otom11_init(void)
{
s3c_i2c0_set_platdata(NULL);
+
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(otom11_devices, ARRAY_SIZE(otom11_devices));
}
diff --git a/arch/arm/mach-s3c24xx/mach-qt2410.c b/arch/arm/mach-s3c/mach-qt2410.c
similarity index 88%
rename from arch/arm/mach-s3c24xx/mach-qt2410.c
rename to arch/arm/mach-s3c/mach-qt2410.c
index f3131d9..151e8e3 100644
--- a/arch/arm/mach-s3c24xx/mach-qt2410.c
+++ b/arch/arm/mach-s3c/mach-qt2410.c
@@ -28,26 +28,23 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-lcd.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc qt2410_iodesc[] __initdata = {
{ 0xe0000000, __phys_to_pfn(S3C2410_CS3+0x01000000), SZ_1M, MT_DEVICE }
@@ -225,6 +222,20 @@ static struct gpiod_lookup_table qt2410_spi_gpiod_table = {
},
};
+static struct gpiod_lookup_table qt2410_mmc_gpiod_table = {
+ .dev_id = "s3c2410-sdi",
+ .table = {
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
/* Board devices */
static struct platform_device *qt2410_devices[] __initdata = {
@@ -309,13 +320,13 @@ static void __init qt2410_map_io(void)
{
s3c24xx_init_io(qt2410_iodesc, ARRAY_SIZE(qt2410_iodesc));
s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init qt2410_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init qt2410_machine_init(void)
@@ -343,9 +354,13 @@ static void __init qt2410_machine_init(void)
s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
s3c_i2c0_set_platdata(NULL);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
gpiod_add_lookup_table(&qt2410_spi_gpiod_table);
s3c_gpio_setpull(S3C2410_GPB(0), S3C_GPIO_PULL_NONE);
gpiod_add_lookup_table(&qt2410_led_gpio_table);
+ gpiod_add_lookup_table(&qt2410_mmc_gpiod_table);
platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
s3c_pm_init();
}
diff --git a/arch/arm/mach-s3c64xx/mach-real6410.c b/arch/arm/mach-s3c/mach-real6410.c
similarity index 94%
rename from arch/arm/mach-s3c64xx/mach-real6410.c
rename to arch/arm/mach-s3c/mach-real6410.c
index 1e98e53..9d218a5 100644
--- a/arch/arm/mach-s3c64xx/mach-real6410.c
+++ b/arch/arm/mach-s3c/mach-real6410.c
@@ -24,25 +24,24 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <mach/irqs.h>
-#include <plat/adc.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
+#include <linux/soc/samsung/s3c-adc.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <video/platform_lcd.h>
#include <video/samsung_fimd.h>
-#include <plat/samsung-time.h>
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT
#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
@@ -208,7 +207,7 @@ static void __init real6410_map_io(void)
s3c64xx_init_io(NULL, 0);
s3c24xx_init_clocks(12000000);
s3c24xx_init_uarts(real6410_uartcfgs, ARRAY_SIZE(real6410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
/* set the LCD type */
tmp = __raw_readl(S3C64XX_SPCON);
@@ -330,6 +329,5 @@ MACHINE_START(REAL6410, "REAL6410")
.init_irq = s3c6410_init_irq,
.map_io = real6410_map_io,
.init_machine = real6410_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-rx1950.c b/arch/arm/mach-s3c/mach-rx1950.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/mach-rx1950.c
rename to arch/arm/mach-s3c/mach-rx1950.c
index 3645b9c..b9758f0 100644
--- a/arch/arm/mach-s3c24xx/mach-rx1950.c
+++ b/arch/arm/mach-s3c/mach-rx1950.c
@@ -42,21 +42,20 @@
#include <linux/platform_data/mtd-nand-s3c2410.h>
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <sound/uda1380.h>
-#include <mach/fb.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
-#include <plat/gpio-cfg.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "gpio-cfg.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "h1940.h"
#define LCD_PWM_PERIOD 192960
@@ -361,14 +360,17 @@ static struct s3c2410fb_mach_info rx1950_lcd_cfg = {
.lpcsel = 0x02,
.gpccon = 0xaa9556a9,
.gpccon_mask = 0xffc003fc,
+ .gpccon_reg = S3C2410_GPCCON,
.gpcup = 0x0000ffff,
.gpcup_mask = 0xffffffff,
+ .gpcup_reg = S3C2410_GPCUP,
.gpdcon = 0xaa90aaa1,
.gpdcon_mask = 0xffc0fff0,
+ .gpdcon_reg = S3C2410_GPDCON,
.gpdup = 0x0000fcfd,
.gpdup_mask = 0xffffffff,
-
+ .gpdup_reg = S3C2410_GPDUP,
};
static struct pwm_lookup rx1950_pwm_lookup[] = {
@@ -549,6 +551,8 @@ static struct platform_device rx1950_backlight = {
static void rx1950_set_mmc_power(unsigned char power_mode, unsigned short vdd)
{
+ s3c24xx_mci_def_set_power(power_mode, vdd);
+
switch (power_mode) {
case MMC_POWER_OFF:
gpio_direction_output(S3C2410_GPJ(1), 0);
@@ -571,9 +575,16 @@ static struct gpiod_lookup_table rx1950_mmc_gpio_table = {
.dev_id = "s3c2410-sdi",
.table = {
/* Card detect S3C2410_GPF(5) */
- GPIO_LOOKUP("GPF", 5, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOF", 5, "cd", GPIO_ACTIVE_LOW),
/* Write protect S3C2410_GPH(8) */
- GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_LOW),
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
{ },
},
};
@@ -767,7 +778,7 @@ static void __init rx1950_map_io(void)
{
s3c24xx_init_io(rx1950_iodesc, ARRAY_SIZE(rx1950_iodesc));
s3c24xx_init_uarts(rx1950_uartcfgs, ARRAY_SIZE(rx1950_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
/* setup PM */
@@ -781,7 +792,7 @@ static void __init rx1950_map_io(void)
static void __init rx1950_init_time(void)
{
s3c2442_init_clocks(16934000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init rx1950_init_machine(void)
@@ -829,6 +840,9 @@ static void __init rx1950_init_machine(void)
pwm_add_table(rx1950_pwm_lookup, ARRAY_SIZE(rx1950_pwm_lookup));
gpiod_add_lookup_table(&rx1950_audio_gpio_table);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(rx1950_devices, ARRAY_SIZE(rx1950_devices));
i2c_register_board_info(0, rx1950_i2c_devices,
diff --git a/arch/arm/mach-s3c24xx/mach-rx3715.c b/arch/arm/mach-s3c/mach-rx3715.c
similarity index 89%
rename from arch/arm/mach-s3c24xx/mach-rx3715.c
rename to arch/arm/mach-s3c/mach-rx3715.c
index 017010d..a03662a 100644
--- a/arch/arm/mach-s3c24xx/mach-rx3715.c
+++ b/arch/arm/mach-s3c/mach-rx3715.c
@@ -30,22 +30,20 @@
#include <asm/mach/map.h>
#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "h1940.h"
static struct map_desc rx3715_iodesc[] __initdata = {
@@ -125,13 +123,17 @@ static struct s3c2410fb_mach_info rx3715_fb_info __initdata = {
.gpccon = 0xaa955699,
.gpccon_mask = 0xffc003cc,
+ .gpccon_reg = S3C2410_GPCCON,
.gpcup = 0x0000ffff,
.gpcup_mask = 0xffffffff,
+ .gpcup_reg = S3C2410_GPCUP,
.gpdcon = 0xaa95aaa1,
.gpdcon_mask = 0xffc0fff0,
+ .gpdcon_reg = S3C2410_GPDCON,
.gpdup = 0x0000faff,
.gpdup_mask = 0xffffffff,
+ .gpdup_reg = S3C2410_GPDUP,
};
static struct mtd_partition __initdata rx3715_nand_part[] = {
@@ -174,13 +176,13 @@ static void __init rx3715_map_io(void)
{
s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc));
s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init rx3715_init_time(void)
{
s3c2440_init_clocks(16934000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
/* H1940 and RX3715 need to reserve this for suspend */
@@ -199,6 +201,9 @@ static void __init rx3715_init_machine(void)
s3c_nand_set_platdata(&rx3715_nand_info);
s3c24xx_fb_set_platdata(&rx3715_fb_info);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(rx3715_devices, ARRAY_SIZE(rx3715_devices));
}
diff --git a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c b/arch/arm/mach-s3c/mach-s3c2416-dt.c
similarity index 91%
rename from arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
rename to arch/arm/mach-s3c/mach-s3c2416-dt.c
index aa71027..418544d 100644
--- a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
+++ b/arch/arm/mach-s3c/mach-s3c2416-dt.c
@@ -16,12 +16,12 @@
#include <linux/serial_s3c.h>
#include <asm/mach/arch.h>
-#include <mach/map.h>
+#include "map.h"
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
-#include "common.h"
+#include "s3c24xx.h"
static void __init s3c2416_dt_map_io(void)
{
diff --git a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c b/arch/arm/mach-s3c/mach-s3c64xx-dt.c
similarity index 70%
rename from arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c
rename to arch/arm/mach-s3c/mach-s3c64xx-dt.c
index 1724f5e..00169c1 100644
--- a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c
+++ b/arch/arm/mach-s3c/mach-s3c64xx-dt.c
@@ -8,11 +8,10 @@
#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <plat/cpu.h>
-#include <mach/map.h>
+#include "cpu.h"
+#include "map.h"
-#include "common.h"
-#include "watchdog-reset.h"
+#include "s3c64xx.h"
/*
* IO mapping for shared system controller IP.
@@ -39,20 +38,6 @@ static void __init s3c64xx_dt_map_io(void)
panic("SoC is not S3C64xx!");
}
-static void __init s3c64xx_dt_init_machine(void)
-{
- samsung_wdt_reset_of_init();
-}
-
-static void s3c64xx_dt_restart(enum reboot_mode mode, const char *cmd)
-{
- if (mode != REBOOT_SOFT)
- samsung_wdt_reset();
-
- /* if all else fails, or mode was for soft, jump to 0 */
- soft_restart(0);
-}
-
static const char *const s3c64xx_dt_compat[] __initconst = {
"samsung,s3c6400",
"samsung,s3c6410",
@@ -63,6 +48,4 @@ DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)")
/* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */
.dt_compat = s3c64xx_dt_compat,
.map_io = s3c64xx_dt_map_io,
- .init_machine = s3c64xx_dt_init_machine,
- .restart = s3c64xx_dt_restart,
MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.c b/arch/arm/mach-s3c/mach-smartq.c
similarity index 96%
rename from arch/arm/mach-s3c64xx/mach-smartq.c
rename to arch/arm/mach-s3c/mach-smartq.c
index 5025db6..5b6e7c2 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.c
+++ b/arch/arm/mach-s3c/mach-smartq.c
@@ -18,25 +18,24 @@
#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
+#include "cpu.h"
+#include "devs.h"
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
+#include "gpio-cfg.h"
#include <linux/platform_data/hwmon-s3c.h>
#include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
#include <linux/platform_data/touchscreen-s3c2410.h>
#include <video/platform_lcd.h>
-#include <plat/samsung-time.h>
-#include "common.h"
+#include "s3c64xx.h"
#include "mach-smartq.h"
-#include "regs-modem.h"
+#include "regs-modem-s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT
#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
@@ -384,7 +383,7 @@ void __init smartq_map_io(void)
s3c64xx_set_xtal_freq(12000000);
s3c64xx_set_xusbxti_freq(12000000);
s3c24xx_init_uarts(smartq_uartcfgs, ARRAY_SIZE(smartq_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
smartq_lcd_mode_set();
}
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.h b/arch/arm/mach-s3c/mach-smartq.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/mach-smartq.h
rename to arch/arm/mach-s3c/mach-smartq.h
diff --git a/arch/arm/mach-s3c64xx/mach-smartq5.c b/arch/arm/mach-s3c/mach-smartq5.c
similarity index 91%
rename from arch/arm/mach-s3c64xx/mach-smartq5.c
rename to arch/arm/mach-s3c/mach-smartq5.c
index 44e9edb..8c94022 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq5.c
+++ b/arch/arm/mach-s3c/mach-smartq5.c
@@ -15,17 +15,16 @@
#include <video/samsung_fimd.h>
#include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
+#include "gpio-cfg.h"
-#include "common.h"
+#include "s3c64xx.h"
#include "mach-smartq.h"
static struct gpio_led smartq5_leds[] = {
@@ -151,6 +150,5 @@ MACHINE_START(SMARTQ5, "SmartQ 5")
.init_irq = s3c6410_init_irq,
.map_io = smartq_map_io,
.init_machine = smartq5_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smartq7.c b/arch/arm/mach-s3c/mach-smartq7.c
similarity index 92%
rename from arch/arm/mach-s3c64xx/mach-smartq7.c
rename to arch/arm/mach-s3c/mach-smartq7.c
index 815ee7d..ab24396 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq7.c
+++ b/arch/arm/mach-s3c/mach-smartq7.c
@@ -15,17 +15,16 @@
#include <video/samsung_fimd.h>
#include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
+#include "gpio-cfg.h"
-#include "common.h"
+#include "s3c64xx.h"
#include "mach-smartq.h"
static struct gpio_led smartq7_leds[] = {
@@ -167,6 +166,5 @@ MACHINE_START(SMARTQ7, "SmartQ 7")
.init_irq = s3c6410_init_irq,
.map_io = smartq_map_io,
.init_machine = smartq7_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2410.c b/arch/arm/mach-s3c/mach-smdk2410.c
similarity index 86%
rename from arch/arm/mach-s3c24xx/mach-smdk2410.c
rename to arch/arm/mach-s3c/mach-smdk2410.c
index 18dfef5..ca83d5a 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2410.c
+++ b/arch/arm/mach-s3c/mach-smdk2410.c
@@ -19,23 +19,23 @@
#include <linux/serial_s3c.h>
#include <linux/platform_device.h>
#include <linux/io.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc smdk2410_iodesc[] __initdata = {
/* nothing here yet */
@@ -81,19 +81,22 @@ static void __init smdk2410_map_io(void)
{
s3c24xx_init_io(smdk2410_iodesc, ARRAY_SIZE(smdk2410_iodesc));
s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init smdk2410_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init smdk2410_init(void)
{
s3c_i2c0_set_platdata(NULL);
platform_add_devices(smdk2410_devices, ARRAY_SIZE(smdk2410_devices));
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
smdk_machine_init();
}
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2413.c b/arch/arm/mach-s3c/mach-smdk2413.c
similarity index 86%
rename from arch/arm/mach-s3c24xx/mach-smdk2413.c
rename to arch/arm/mach-s3c/mach-smdk2413.c
index ca80167..c43095b 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2413.c
+++ b/arch/arm/mach-s3c/mach-smdk2413.c
@@ -23,27 +23,26 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/hardware/iomd.h>
#include <asm/setup.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
//#include <asm/debug-ll.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc smdk2413_iodesc[] __initdata = {
};
@@ -99,13 +98,13 @@ static void __init smdk2413_map_io(void)
{
s3c24xx_init_io(smdk2413_iodesc, ARRAY_SIZE(smdk2413_iodesc));
s3c24xx_init_uarts(smdk2413_uartcfgs, ARRAY_SIZE(smdk2413_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init smdk2413_init_time(void)
{
s3c2412_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init smdk2413_machine_init(void)
@@ -119,6 +118,9 @@ static void __init smdk2413_machine_init(void)
s3c24xx_udc_set_platdata(&smdk2413_udc_cfg);
s3c_i2c0_set_platdata(NULL);
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(smdk2413_devices, ARRAY_SIZE(smdk2413_devices));
smdk_machine_init();
@@ -132,7 +134,7 @@ MACHINE_START(S3C2413, "S3C2413")
.init_irq = s3c2412_init_irq,
.map_io = smdk2413_map_io,
.init_machine = smdk2413_machine_init,
- .init_time = samsung_timer_init,
+ .init_time = s3c24xx_timer_init,
MACHINE_END
MACHINE_START(SMDK2412, "SMDK2412")
@@ -143,7 +145,7 @@ MACHINE_START(SMDK2412, "SMDK2412")
.init_irq = s3c2412_init_irq,
.map_io = smdk2413_map_io,
.init_machine = smdk2413_machine_init,
- .init_time = samsung_timer_init,
+ .init_time = s3c24xx_timer_init,
MACHINE_END
MACHINE_START(SMDK2413, "SMDK2413")
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2416.c b/arch/arm/mach-s3c/mach-smdk2416.c
similarity index 93%
rename from arch/arm/mach-s3c24xx/mach-smdk2416.c
rename to arch/arm/mach-s3c/mach-smdk2416.c
index 61c3e45..4d883a7 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2416.c
+++ b/arch/arm/mach-s3c/mach-smdk2416.c
@@ -25,31 +25,29 @@
#include <asm/mach/irq.h>
#include <video/samsung_fimd.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include "regs-s3c2443-clock.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/leds-s3c24xx.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
#include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
#include <linux/platform_data/usb-s3c2410_udc.h>
#include <linux/platform_data/s3c-hsudc.h>
-#include <plat/samsung-time.h>
-#include <plat/fb.h>
+#include "fb.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc smdk2416_iodesc[] __initdata = {
/* ISA IO Space map (memory space selected by A24) */
@@ -215,14 +213,14 @@ static struct platform_device *smdk2416_devices[] __initdata = {
static void __init smdk2416_init_time(void)
{
s3c2416_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init smdk2416_map_io(void)
{
s3c24xx_init_io(smdk2416_iodesc, ARRAY_SIZE(smdk2416_iodesc));
s3c24xx_init_uarts(smdk2416_uartcfgs, ARRAY_SIZE(smdk2416_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init smdk2416_machine_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2440.c b/arch/arm/mach-s3c/mach-smdk2440.c
similarity index 87%
rename from arch/arm/mach-s3c24xx/mach-smdk2440.c
rename to arch/arm/mach-s3c/mach-smdk2440.c
index 7bafcd8..7f6fe0d 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2440.c
+++ b/arch/arm/mach-s3c/mach-smdk2440.c
@@ -23,22 +23,21 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc smdk2440_iodesc[] __initdata = {
/* ISA IO Space map (memory space selected by A24) */
@@ -137,6 +136,11 @@ static struct s3c2410fb_mach_info smdk2440_fb_info __initdata = {
.gpdcon_mask = 0xffffffff,
.gpdup = 0x0000faff,
.gpdup_mask = 0xffffffff,
+
+ .gpccon_reg = S3C2410_GPCCON,
+ .gpcup_reg = S3C2410_GPCUP,
+ .gpdcon_reg = S3C2410_GPDCON,
+ .gpdup_reg = S3C2410_GPDUP,
#endif
.lpcsel = ((0xCE6) & ~7) | 1<<4,
@@ -154,20 +158,22 @@ static void __init smdk2440_map_io(void)
{
s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc));
s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init smdk2440_init_time(void)
{
s3c2440_init_clocks(16934400);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init smdk2440_machine_init(void)
{
s3c24xx_fb_set_platdata(&smdk2440_fb_info);
s3c_i2c0_set_platdata(NULL);
-
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(smdk2440_devices, ARRAY_SIZE(smdk2440_devices));
smdk_machine_init();
}
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2443.c b/arch/arm/mach-s3c/mach-smdk2443.c
similarity index 90%
rename from arch/arm/mach-s3c24xx/mach-smdk2443.c
rename to arch/arm/mach-s3c/mach-smdk2443.c
index 2358ed5..fc54c91 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2443.c
+++ b/arch/arm/mach-s3c/mach-smdk2443.c
@@ -22,22 +22,19 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
static struct map_desc smdk2443_iodesc[] __initdata = {
/* ISA IO Space map (memory space selected by A24) */
@@ -112,13 +109,13 @@ static void __init smdk2443_map_io(void)
{
s3c24xx_init_io(smdk2443_iodesc, ARRAY_SIZE(smdk2443_iodesc));
s3c24xx_init_uarts(smdk2443_uartcfgs, ARRAY_SIZE(smdk2443_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init smdk2443_init_time(void)
{
s3c2443_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init smdk2443_machine_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6400.c b/arch/arm/mach-s3c/mach-smdk6400.c
similarity index 87%
rename from arch/arm/mach-s3c64xx/mach-smdk6400.c
rename to arch/arm/mach-s3c/mach-smdk6400.c
index cbd1684..8272213 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6400.c
+++ b/arch/arm/mach-s3c/mach-smdk6400.c
@@ -23,16 +23,14 @@
#include <asm/mach/irq.h>
#include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <plat/samsung-time.h>
+#include "gpio-samsung.h"
-#include "common.h"
+#include "s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
@@ -62,7 +60,7 @@ static void __init smdk6400_map_io(void)
s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc));
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
}
static struct platform_device *smdk6400_devices[] __initdata = {
@@ -88,6 +86,5 @@ MACHINE_START(SMDK6400, "SMDK6400")
.init_irq = s3c6400_init_irq,
.map_io = smdk6400_map_io,
.init_machine = smdk6400_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c/mach-smdk6410.c
similarity index 96%
rename from arch/arm/mach-s3c64xx/mach-smdk6410.c
rename to arch/arm/mach-s3c/mach-smdk6410.c
index 56f406c..ae18c13 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c/mach-smdk6410.c
@@ -45,32 +45,30 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
#include <linux/platform_data/ata-samsung_cf.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
+#include "fb.h"
+#include "gpio-cfg.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc.h>
+#include "devs.h"
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-adc.h>
#include <linux/platform_data/touchscreen-s3c2410.h>
-#include <plat/keypad.h>
-#include <plat/samsung-time.h>
+#include "keypad.h"
-#include "backlight.h"
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
-#include "regs-sys.h"
+#include "backlight-s3c64xx.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
@@ -635,7 +633,7 @@ static void __init smdk6410_map_io(void)
s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
s3c64xx_set_xtal_freq(12000000);
s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
/* set the LCD type */
@@ -704,6 +702,5 @@ MACHINE_START(SMDK6410, "SMDK6410")
.init_irq = s3c6410_init_irq,
.map_io = smdk6410_map_io,
.init_machine = smdk6410_machine_init,
- .init_time = samsung_timer_init,
- .restart = s3c64xx_restart,
+ .init_time = s3c64xx_timer_init,
MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-tct_hammer.c b/arch/arm/mach-s3c/mach-tct_hammer.c
similarity index 81%
rename from arch/arm/mach-s3c24xx/mach-tct_hammer.c
rename to arch/arm/mach-s3c/mach-tct_hammer.c
index 8d8ddd6..2a61df3 100644
--- a/arch/arm/mach-s3c24xx/mach-tct_hammer.c
+++ b/arch/arm/mach-s3c/mach-tct_hammer.c
@@ -7,6 +7,7 @@
// derived from linux/arch/arm/mach-s3c2410/mach-bast.c, written by
// Ben Dooks <ben@simtec.co.uk>
+#include <linux/gpio/machine.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
@@ -24,21 +25,19 @@
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/map.h>
#include <linux/mtd/physmap.h>
-#include <plat/samsung-time.h>
-#include "common.h"
+#include "s3c24xx.h"
static struct resource tct_hammer_nor_resource =
DEFINE_RES_MEM(0x00000000, SZ_16M);
@@ -103,6 +102,19 @@ static struct s3c2410_uartcfg tct_hammer_uartcfgs[] = {
}
};
+static struct gpiod_lookup_table tct_hammer_mmc_gpio_table = {
+ .dev_id = "s3c2410-sdi",
+ .table = {
+ /* bus pins */
+ GPIO_LOOKUP_IDX("GPIOE", 5, "bus", 0, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 6, "bus", 1, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 7, "bus", 2, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 8, "bus", 3, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 9, "bus", 4, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
static struct platform_device *tct_hammer_devices[] __initdata = {
&s3c_device_adc,
@@ -119,18 +131,19 @@ static void __init tct_hammer_map_io(void)
{
s3c24xx_init_io(tct_hammer_iodesc, ARRAY_SIZE(tct_hammer_iodesc));
s3c24xx_init_uarts(tct_hammer_uartcfgs, ARRAY_SIZE(tct_hammer_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init tct_hammer_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init tct_hammer_init(void)
{
s3c_i2c0_set_platdata(NULL);
+ gpiod_add_lookup_table(&tct_hammer_mmc_gpio_table);
platform_add_devices(tct_hammer_devices, ARRAY_SIZE(tct_hammer_devices));
}
diff --git a/arch/arm/mach-s3c24xx/mach-vr1000.c b/arch/arm/mach-s3c/mach-vr1000.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/mach-vr1000.c
rename to arch/arm/mach-s3c/mach-vr1000.c
index 6a3fb2b..5c3d07c 100644
--- a/arch/arm/mach-s3c24xx/mach-vr1000.c
+++ b/arch/arm/mach-s3c/mach-vr1000.c
@@ -35,17 +35,15 @@
#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/platform_data/asoc-s3c24xx_simtec.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
#include "bast.h"
-#include "common.h"
+#include "s3c24xx.h"
#include "simtec.h"
#include "vr1000.h"
@@ -328,13 +326,13 @@ static void __init vr1000_map_io(void)
s3c24xx_init_io(vr1000_iodesc, ARRAY_SIZE(vr1000_iodesc));
s3c24xx_init_uarts(vr1000_uartcfgs, ARRAY_SIZE(vr1000_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init vr1000_init_time(void)
{
s3c2410_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init vr1000_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-vstms.c b/arch/arm/mach-s3c/mach-vstms.c
similarity index 88%
rename from arch/arm/mach-s3c24xx/mach-vstms.c
rename to arch/arm/mach-s3c/mach-vstms.c
index c5fa215..05f19f5 100644
--- a/arch/arm/mach-s3c24xx/mach-vstms.c
+++ b/arch/arm/mach-s3c/mach-vstms.c
@@ -24,24 +24,23 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <linux/platform_data/i2c-s3c2410.h>
#include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
-#include "common.h"
+#include "s3c24xx.h"
static struct map_desc vstms_iodesc[] __initdata = {
};
@@ -136,20 +135,22 @@ static void __init vstms_map_io(void)
{
s3c24xx_init_io(vstms_iodesc, ARRAY_SIZE(vstms_iodesc));
s3c24xx_init_uarts(vstms_uartcfgs, ARRAY_SIZE(vstms_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+ s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
}
static void __init vstms_init_time(void)
{
s3c2412_init_clocks(12000000);
- samsung_timer_init();
+ s3c24xx_timer_init();
}
static void __init vstms_init(void)
{
s3c_i2c0_set_platdata(NULL);
s3c_nand_set_platdata(&vstms_nand_info);
-
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
platform_add_devices(vstms_devices, ARRAY_SIZE(vstms_devices));
}
diff --git a/arch/arm/plat-samsung/include/plat/map-s3c.h b/arch/arm/mach-s3c/map-s3c.h
similarity index 87%
rename from arch/arm/plat-samsung/include/plat/map-s3c.h
rename to arch/arm/mach-s3c/map-s3c.h
index 4244acbf..a18fdd3 100644
--- a/arch/arm/plat-samsung/include/plat/map-s3c.h
+++ b/arch/arm/mach-s3c/map-s3c.h
@@ -9,6 +9,8 @@
#ifndef __ASM_PLAT_MAP_S3C_H
#define __ASM_PLAT_MAP_S3C_H __FILE__
+#include "map.h"
+
#define S3C24XX_VA_IRQ S3C_VA_IRQ
#define S3C24XX_VA_MEMCTRL S3C_VA_MEM
#define S3C24XX_VA_UART S3C_VA_UART
@@ -45,16 +47,8 @@
#define S3C_VA_USB_HSPHY S3C64XX_VA_USB_HSPHY
-/*
- * ISA style IO, for each machine to sort out mappings for,
- * if it implements it. We reserve two 16M regions for ISA.
- */
-
#define S3C2410_ADDR(x) S3C_ADDR(x)
-#define S3C24XX_VA_ISA_WORD S3C2410_ADDR(0x02000000)
-#define S3C24XX_VA_ISA_BYTE S3C2410_ADDR(0x03000000)
-
/* deal with the registers that move under the 2412/2413 */
#if defined(CONFIG_CPU_S3C2412)
@@ -71,6 +65,6 @@ extern void __iomem *s3c24xx_va_gpio2;
#define S3C24XX_VA_GPIO2 S3C24XX_VA_GPIO
#endif
-#include <plat/map-s5p.h>
+#include "map-s5p.h"
#endif /* __ASM_PLAT_MAP_S3C_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/map.h b/arch/arm/mach-s3c/map-s3c24xx.h
similarity index 96%
rename from arch/arm/mach-s3c24xx/include/mach/map.h
rename to arch/arm/mach-s3c/map-s3c24xx.h
index bca9311..b5dba78 100644
--- a/arch/arm/mach-s3c24xx/include/mach/map.h
+++ b/arch/arm/mach-s3c/map-s3c24xx.h
@@ -9,8 +9,8 @@
#ifndef __ASM_ARCH_MAP_H
#define __ASM_ARCH_MAP_H
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
+#include <mach/map-base.h>
+#include "map-s3c.h"
/*
* interrupt controller is the first thing we put in, to make
@@ -86,6 +86,8 @@
#define S3C2410_PA_SPI (0x59000000)
#define S3C2443_PA_SPI0 (0x52000000)
#define S3C2443_PA_SPI1 S3C2410_PA_SPI
+#define S3C2410_SPI1 (0x20)
+#define S3C2412_SPI1 (0x100)
/* SDI */
#define S3C2410_PA_SDI (0x5A000000)
diff --git a/arch/arm/mach-s3c64xx/include/mach/map.h b/arch/arm/mach-s3c/map-s3c64xx.h
similarity index 97%
rename from arch/arm/mach-s3c64xx/include/mach/map.h
rename to arch/arm/mach-s3c/map-s3c64xx.h
index 9372a53..d7740d2 100644
--- a/arch/arm/mach-s3c64xx/include/mach/map.h
+++ b/arch/arm/mach-s3c/map-s3c64xx.h
@@ -11,8 +11,8 @@
#ifndef __ASM_ARCH_MAP_H
#define __ASM_ARCH_MAP_H __FILE__
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
+#include <mach/map-base.h>
+#include "map-s3c.h"
/*
* Post-mux Chip Select Regions Xm0CSn_
diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/mach-s3c/map-s5p.h
similarity index 85%
rename from arch/arm/plat-samsung/include/plat/map-s5p.h
rename to arch/arm/mach-s3c/map-s5p.h
index d69a0ca..cd23792 100644
--- a/arch/arm/plat-samsung/include/plat/map-s5p.h
+++ b/arch/arm/mach-s3c/map-s5p.h
@@ -9,14 +9,12 @@
#ifndef __ASM_PLAT_MAP_S5P_H
#define __ASM_PLAT_MAP_S5P_H __FILE__
-#define S5P_VA_CHIPID S3C_ADDR(0x02000000)
-
#define VA_VIC(x) (S3C_VA_IRQ + ((x) * 0x10000))
#define VA_VIC0 VA_VIC(0)
#define VA_VIC1 VA_VIC(1)
#define VA_VIC2 VA_VIC(2)
#define VA_VIC3 VA_VIC(3)
-#include <plat/map-s3c.h>
+#include "map-s3c.h"
#endif /* __ASM_PLAT_MAP_S5P_H */
diff --git a/arch/arm/mach-s3c/map.h b/arch/arm/mach-s3c/map.h
new file mode 100644
index 0000000..7cfb517
--- /dev/null
+++ b/arch/arm/mach-s3c/map.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "map-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "map-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/nand-core.h b/arch/arm/mach-s3c/nand-core-s3c24xx.h
similarity index 77%
rename from arch/arm/mach-s3c24xx/nand-core.h
rename to arch/arm/mach-s3c/nand-core-s3c24xx.h
index 8de633d..a143167 100644
--- a/arch/arm/mach-s3c24xx/nand-core.h
+++ b/arch/arm/mach-s3c/nand-core-s3c24xx.h
@@ -6,8 +6,8 @@
* S3C - Nand Controller core functions
*/
-#ifndef __ASM_ARCH_NAND_CORE_H
-#define __ASM_ARCH_NAND_CORE_H __FILE__
+#ifndef __ASM_ARCH_NAND_CORE_S3C24XX_H
+#define __ASM_ARCH_NAND_CORE_S3C24XX_H __FILE__
/* These functions are only for use with the core support code, such as
* the cpu specific initialisation code
@@ -21,4 +21,4 @@ static inline void s3c_nand_setname(char *name)
#endif
}
-#endif /* __ASM_ARCH_NAND_CORE_H */
+#endif /* __ASM_ARCH_NAND_CORE_S3C24XX_H */
diff --git a/arch/arm/mach-s3c64xx/onenand-core.h b/arch/arm/mach-s3c/onenand-core-s3c64xx.h
similarity index 82%
rename from arch/arm/mach-s3c64xx/onenand-core.h
rename to arch/arm/mach-s3c/onenand-core-s3c64xx.h
index 0cf6b5e..e2dfdd1 100644
--- a/arch/arm/mach-s3c64xx/onenand-core.h
+++ b/arch/arm/mach-s3c/onenand-core-s3c64xx.h
@@ -7,8 +7,8 @@
* Samsung OneNAD Controller core functions
*/
-#ifndef __ASM_ARCH_ONENAND_CORE_H
-#define __ASM_ARCH_ONENAND_CORE_H __FILE__
+#ifndef __ASM_ARCH_ONENAND_CORE_S3C64XX_H
+#define __ASM_ARCH_ONENAND_CORE_S3C64XX_H __FILE__
/* These functions are only for use with the core support code, such as
* the cpu specific initialisation code
@@ -29,4 +29,4 @@ static inline void s3c64xx_onenand1_setname(char *name)
#endif
}
-#endif /* __ASM_ARCH_ONENAND_CORE_H */
+#endif /* __ASM_ARCH_ONENAND_CORE_S3C64XX_H */
diff --git a/arch/arm/mach-s3c24xx/osiris.h b/arch/arm/mach-s3c/osiris.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/osiris.h
rename to arch/arm/mach-s3c/osiris.h
diff --git a/arch/arm/mach-s3c24xx/otom.h b/arch/arm/mach-s3c/otom.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/otom.h
rename to arch/arm/mach-s3c/otom.h
diff --git a/arch/arm/mach-s3c64xx/pl080.c b/arch/arm/mach-s3c/pl080.c
similarity index 98%
rename from arch/arm/mach-s3c64xx/pl080.c
rename to arch/arm/mach-s3c/pl080.c
index 152edbe..4730f08 100644
--- a/arch/arm/mach-s3c64xx/pl080.c
+++ b/arch/arm/mach-s3c/pl080.c
@@ -10,11 +10,11 @@
#include <linux/amba/pl08x.h>
#include <linux/of.h>
-#include <plat/cpu.h>
+#include "cpu.h"
#include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
-#include "regs-sys.h"
+#include "regs-sys-s3c64xx.h"
static int pl08x_get_xfer_signal(const struct pl08x_channel_data *cd)
{
diff --git a/arch/arm/plat-samsung/platformdata.c b/arch/arm/mach-s3c/platformdata.c
similarity index 95%
rename from arch/arm/plat-samsung/platformdata.c
rename to arch/arm/mach-s3c/platformdata.c
index cbc3b4b..e643c81 100644
--- a/arch/arm/plat-samsung/platformdata.c
+++ b/arch/arm/mach-s3c/platformdata.c
@@ -9,8 +9,8 @@
#include <linux/string.h>
#include <linux/platform_device.h>
-#include <plat/devs.h>
-#include <plat/sdhci.h>
+#include "devs.h"
+#include "sdhci.h"
void __init *s3c_set_platdata(void *pd, size_t pdsize,
struct platform_device *pdev)
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2410.c b/arch/arm/mach-s3c/pll-s3c2410.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/pll-s3c2410.c
rename to arch/arm/mach-s3c/pll-s3c2410.c
index 0561f79..3fbc99e 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2410.c
+++ b/arch/arm/mach-s3c/pll-s3c2410.c
@@ -15,8 +15,8 @@
#include <linux/clk.h>
#include <linux/err.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
/* This array should be sorted in ascending order of the frequencies */
static struct cpufreq_frequency_table pll_vals_12MHz[] = {
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c b/arch/arm/mach-s3c/pll-s3c2440-12000000.c
similarity index 97%
rename from arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
rename to arch/arm/mach-s3c/pll-s3c2440-12000000.c
index 2ec3a2f..fdb8e8c 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
+++ b/arch/arm/mach-s3c/pll-s3c2440-12000000.c
@@ -13,8 +13,8 @@
#include <linux/clk.h>
#include <linux/err.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
/* This array should be sorted in ascending order of the frequencies */
static struct cpufreq_frequency_table s3c2440_plls_12[] = {
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c b/arch/arm/mach-s3c/pll-s3c2440-16934400.c
similarity index 98%
rename from arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
rename to arch/arm/mach-s3c/pll-s3c2440-16934400.c
index 4b3d9e36..438b6fc 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
+++ b/arch/arm/mach-s3c/pll-s3c2440-16934400.c
@@ -13,8 +13,8 @@
#include <linux/clk.h>
#include <linux/err.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
/* This array should be sorted in ascending order of the frequencies */
static struct cpufreq_frequency_table s3c2440_plls_169344[] = {
diff --git a/arch/arm/plat-samsung/pm-common.c b/arch/arm/mach-s3c/pm-common.c
similarity index 94%
rename from arch/arm/plat-samsung/pm-common.c
rename to arch/arm/mach-s3c/pm-common.c
index 59a10c6d..618bd44 100644
--- a/arch/arm/plat-samsung/pm-common.c
+++ b/arch/arm/mach-s3c/pm-common.c
@@ -12,7 +12,7 @@
#include <linux/io.h>
#include <linux/kernel.h>
-#include <plat/pm-common.h>
+#include "pm-common.h"
/* helper functions to save and restore register state */
@@ -55,6 +55,8 @@ void s3c_pm_do_restore(const struct sleep_save *ptr, int count)
/**
* s3c_pm_do_restore_core() - early restore register values from save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
*
* This is similar to s3c_pm_do_restore() except we try and minimise the
* side effects of the function in case registers that hardware might need
diff --git a/arch/arm/mach-s3c/pm-common.h b/arch/arm/mach-s3c/pm-common.h
new file mode 100644
index 0000000..18b9607
--- /dev/null
+++ b/arch/arm/mach-s3c/pm-common.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Tomasz Figa <t.figa@samsung.com>
+ * Copyright (c) 2004 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Written by Ben Dooks, <ben@simtec.co.uk>
+ */
+
+#ifndef __PLAT_SAMSUNG_PM_COMMON_H
+#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
+
+#include <linux/irq.h>
+#include <linux/soc/samsung/s3c-pm.h>
+
+/* sleep save info */
+
+/**
+ * struct sleep_save - save information for shared peripherals.
+ * @reg: Pointer to the register to save.
+ * @val: Holder for the value saved from reg.
+ *
+ * This describes a list of registers which is used by the pm core and
+ * other subsystem to save and restore register values over suspend.
+ */
+struct sleep_save {
+ void __iomem *reg;
+ unsigned long val;
+};
+
+#define SAVE_ITEM(x) \
+ { .reg = (x) }
+
+/* helper functions to save/restore lists of registers. */
+
+extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
+
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/pm-core.h b/arch/arm/mach-s3c/pm-core-s3c24xx.h
similarity index 94%
rename from arch/arm/mach-s3c24xx/include/mach/pm-core.h
rename to arch/arm/mach-s3c/pm-core-s3c24xx.h
index 5e4ce89..bcb7978 100644
--- a/arch/arm/mach-s3c24xx/include/mach/pm-core.h
+++ b/arch/arm/mach-s3c/pm-core-s3c24xx.h
@@ -11,10 +11,12 @@
#include <linux/io.h>
#include "regs-clock.h"
-#include "regs-irq.h"
+#include "regs-irq-s3c24xx.h"
+#include <mach/irqs.h>
static inline void s3c_pm_debug_init_uart(void)
{
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
unsigned long tmp = __raw_readl(S3C2410_CLKCON);
/* re-start uart clocks */
@@ -24,6 +26,7 @@ static inline void s3c_pm_debug_init_uart(void)
__raw_writel(tmp, S3C2410_CLKCON);
udelay(10);
+#endif
}
static inline void s3c_pm_arch_prepare_irqs(void)
@@ -75,11 +78,6 @@ static inline void s3c_pm_arch_show_resume_irqs(void)
s3c_irqwake_eintmask);
}
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
- struct pm_uart_save *save)
-{
-}
-
static inline void s3c_pm_restored_gpios(void) { }
static inline void samsung_pm_saved_gpios(void) { }
diff --git a/arch/arm/mach-s3c/pm-core-s3c64xx.h b/arch/arm/mach-s3c/pm-core-s3c64xx.h
new file mode 100644
index 0000000..06f564e5
--- /dev/null
+++ b/arch/arm/mach-s3c/pm-core-s3c64xx.h
@@ -0,0 +1,84 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - PM core support for arch/arm/plat-s3c/pm.c
+ */
+
+#ifndef __MACH_S3C64XX_PM_CORE_H
+#define __MACH_S3C64XX_PM_CORE_H __FILE__
+
+#include <linux/serial_s3c.h>
+#include <linux/delay.h>
+
+#include "regs-gpio.h"
+#include "regs-clock.h"
+#include "map.h"
+
+static inline void s3c_pm_debug_init_uart(void)
+{
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+ u32 tmp = __raw_readl(S3C_PCLK_GATE);
+
+ /* As a note, since the S3C64XX UARTs generally have multiple
+ * clock sources, we simply enable PCLK at the moment and hope
+ * that the resume settings for the UART are suitable for the
+ * use with PCLK.
+ */
+
+ tmp |= S3C_CLKCON_PCLK_UART0;
+ tmp |= S3C_CLKCON_PCLK_UART1;
+ tmp |= S3C_CLKCON_PCLK_UART2;
+ tmp |= S3C_CLKCON_PCLK_UART3;
+
+ __raw_writel(tmp, S3C_PCLK_GATE);
+ udelay(10);
+#endif
+}
+
+static inline void s3c_pm_arch_prepare_irqs(void)
+{
+ /* VIC should have already been taken care of */
+
+ /* clear any pending EINT0 interrupts */
+ __raw_writel(__raw_readl(S3C64XX_EINT0PEND), S3C64XX_EINT0PEND);
+}
+
+static inline void s3c_pm_arch_stop_clocks(void)
+{
+}
+
+static inline void s3c_pm_arch_show_resume_irqs(void)
+{
+}
+
+/* make these defines, we currently do not have any need to change
+ * the IRQ wake controls depending on the CPU we are running on */
+#ifdef CONFIG_PM_SLEEP
+#define s3c_irqwake_eintallow ((1 << 28) - 1)
+#define s3c_irqwake_intallow (~0)
+#else
+#define s3c_irqwake_eintallow 0
+#define s3c_irqwake_intallow 0
+#endif
+
+static inline void s3c_pm_restored_gpios(void)
+{
+ /* ensure sleep mode has been cleared from the system */
+
+ __raw_writel(0, S3C64XX_SLPEN);
+}
+
+static inline void samsung_pm_saved_gpios(void)
+{
+ /* turn on the sleep mode and keep it there, as it seems that during
+ * suspend the xCON registers get re-set and thus you can end up with
+ * problems between going to sleep and resuming.
+ */
+
+ __raw_writel(S3C64XX_SLPEN_USE_xSLP, S3C64XX_SLPEN);
+}
+#endif /* __MACH_S3C64XX_PM_CORE_H */
diff --git a/arch/arm/mach-s3c/pm-core.h b/arch/arm/mach-s3c/pm-core.h
new file mode 100644
index 0000000..b0e1d27
--- /dev/null
+++ b/arch/arm/mach-s3c/pm-core.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "pm-core-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "pm-core-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/pm-gpio.c b/arch/arm/mach-s3c/pm-gpio.c
similarity index 98%
rename from arch/arm/plat-samsung/pm-gpio.c
rename to arch/arm/mach-s3c/pm-gpio.c
index cb2e3bc..cfdbc23 100644
--- a/arch/arm/plat-samsung/pm-gpio.c
+++ b/arch/arm/mach-s3c/pm-gpio.c
@@ -13,10 +13,10 @@
#include <linux/io.h>
#include <linux/gpio.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
-#include <plat/gpio-core.h>
-#include <plat/pm.h>
+#include "gpio-core.h"
+#include "pm.h"
/* PM GPIO helpers */
diff --git a/arch/arm/mach-s3c24xx/pm-h1940.S b/arch/arm/mach-s3c/pm-h1940.S
similarity index 80%
rename from arch/arm/mach-s3c24xx/pm-h1940.S
rename to arch/arm/mach-s3c/pm-h1940.S
index a7bbe33..3bf6685 100644
--- a/arch/arm/mach-s3c24xx/pm-h1940.S
+++ b/arch/arm/mach-s3c/pm-h1940.S
@@ -7,10 +7,9 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
.text
.global h1940_pm_return
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2410.c b/arch/arm/mach-s3c/pm-s3c2410.c
similarity index 95%
rename from arch/arm/mach-s3c24xx/pm-s3c2410.c
rename to arch/arm/mach-s3c/pm-s3c2410.c
index 2d8ea70..a664198 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2410.c
+++ b/arch/arm/mach-s3c/pm-s3c2410.c
@@ -16,13 +16,12 @@
#include <asm/mach-types.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/gpio-cfg.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "cpu.h"
+#include "pm.h"
#include "h1940.h"
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2412.c b/arch/arm/mach-s3c/pm-s3c2412.c
similarity index 94%
rename from arch/arm/mach-s3c24xx/pm-s3c2412.c
rename to arch/arm/mach-s3c/pm-s3c2412.c
index 2dfdaab..6a96044 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2412.c
+++ b/arch/arm/mach-s3c/pm-s3c2412.c
@@ -19,14 +19,14 @@
#include <asm/cacheflush.h>
#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include <mach/irqs.h>
+#include "regs-gpio.h"
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/wakeup-mask.h>
+#include "cpu.h"
+#include "pm.h"
+#include "wakeup-mask.h"
-#include "regs-dsc.h"
+#include "regs-dsc-s3c24xx.h"
#include "s3c2412-power.h"
extern void s3c2412_sleep_enter(void);
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2416.c b/arch/arm/mach-s3c/pm-s3c2416.c
similarity index 95%
rename from arch/arm/mach-s3c24xx/pm-s3c2416.c
rename to arch/arm/mach-s3c/pm-s3c2416.c
index 9a2f05e..f69ad84 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2416.c
+++ b/arch/arm/mach-s3c/pm-s3c2416.c
@@ -11,10 +11,10 @@
#include <asm/cacheflush.h>
-#include <mach/regs-s3c2443-clock.h>
+#include "regs-s3c2443-clock.h"
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
#include "s3c2412-power.h"
diff --git a/arch/arm/mach-s3c24xx/pm.c b/arch/arm/mach-s3c/pm-s3c24xx.c
similarity index 92%
rename from arch/arm/mach-s3c24xx/pm.c
rename to arch/arm/mach-s3c/pm-s3c24xx.c
index c64988c..3a8f5c3 100644
--- a/arch/arm/mach-s3c24xx/pm.c
+++ b/arch/arm/mach-s3c/pm-s3c24xx.c
@@ -21,17 +21,17 @@
#include <linux/serial_s3c.h>
#include <linux/io.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-irq.h>
-#include <mach/gpio-samsung.h>
+#include "regs-clock.h"
+#include "regs-gpio.h"
+#include "regs-irq.h"
+#include "gpio-samsung.h"
#include <asm/mach/time.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "pm.h"
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
#define PFX "s3c24xx-pm: "
diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c/pm-s3c64xx.c
similarity index 81%
rename from arch/arm/mach-s3c64xx/pm.c
rename to arch/arm/mach-s3c/pm-s3c64xx.c
index fd6dbb2..4f17781 100644
--- a/arch/arm/mach-s3c64xx/pm.c
+++ b/arch/arm/mach-s3c/pm-s3c64xx.c
@@ -14,22 +14,22 @@
#include <linux/gpio.h>
#include <linux/pm_domain.h>
-#include <mach/map.h>
+#include "map.h"
#include <mach/irqs.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/wakeup-mask.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "wakeup-mask.h"
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
+#include "gpio-samsung.h"
-#include "regs-gpio-memport.h"
-#include "regs-modem.h"
-#include "regs-sys.h"
-#include "regs-syscon-power.h"
+#include "regs-gpio-memport-s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-syscon-power-s3c64xx.h"
struct s3c64xx_pm_domain {
char *const name;
@@ -305,6 +305,56 @@ static void s3c64xx_pm_prepare(void)
__raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), S3C64XX_WAKEUP_STAT);
}
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+void s3c_pm_arch_update_uart(void __iomem *regs, struct pm_uart_save *save)
+{
+ u32 ucon;
+ u32 ucon_clk
+ u32 save_clk;
+ u32 new_ucon;
+ u32 delta;
+
+ if (!soc_is_s3c64xx())
+ return;
+
+ ucon = __raw_readl(regs + S3C2410_UCON);
+ ucon_clk = ucon & S3C6400_UCON_CLKMASK;
+ sav_clk = save->ucon & S3C6400_UCON_CLKMASK;
+
+ /* S3C64XX UART blocks only support level interrupts, so ensure that
+ * when we restore unused UART blocks we force the level interrupt
+ * settigs. */
+ save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
+
+ /* We have a constraint on changing the clock type of the UART
+ * between UCLKx and PCLK, so ensure that when we restore UCON
+ * that the CLK field is correctly modified if the bootloader
+ * has changed anything.
+ */
+ if (ucon_clk != save_clk) {
+ new_ucon = save->ucon;
+ delta = ucon_clk ^ save_clk;
+
+ /* change from UCLKx => wrong PCLK,
+ * either UCLK can be tested for by a bit-test
+ * with UCLK0 */
+ if (ucon_clk & S3C6400_UCON_UCLK0 &&
+ !(save_clk & S3C6400_UCON_UCLK0) &&
+ delta & S3C6400_UCON_PCLK2) {
+ new_ucon &= ~S3C6400_UCON_UCLK0;
+ } else if (delta == S3C6400_UCON_PCLK2) {
+ /* as an precaution, don't change from
+ * PCLK2 => PCLK or vice-versa */
+ new_ucon ^= S3C6400_UCON_PCLK2;
+ }
+
+ S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
+ ucon, new_ucon, save->ucon);
+ save->ucon = new_ucon;
+ }
+}
+#endif
+
int __init s3c64xx_pm_init(void)
{
int i;
diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/mach-s3c/pm.c
similarity index 93%
rename from arch/arm/plat-samsung/pm.c
rename to arch/arm/mach-s3c/pm.c
index d6bfd66..c563bb9 100644
--- a/arch/arm/plat-samsung/pm.c
+++ b/arch/arm/mach-s3c/pm.c
@@ -18,15 +18,16 @@
#include <asm/cacheflush.h>
#include <asm/suspend.h>
-#include <mach/map.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-irq.h>
+#include "map.h"
+#include "regs-clock.h"
+#include "regs-irq.h"
#include <mach/irqs.h>
#include <asm/irq.h>
-#include <plat/pm.h>
-#include <mach/pm-core.h>
+#include "cpu.h"
+#include "pm.h"
+#include "pm-core.h"
/* for external use */
@@ -70,8 +71,7 @@ static int s3c_pm_enter(suspend_state_t state)
{
int ret;
/* ensure the debug is initialised (if enabled) */
-
- s3c_pm_debug_init();
+ s3c_pm_debug_init_uart();
S3C_PMDBG("%s(%d)\n", __func__, state);
@@ -100,7 +100,7 @@ static int s3c_pm_enter(suspend_state_t state)
samsung_pm_saved_gpios();
}
- s3c_pm_save_uarts();
+ s3c_pm_save_uarts(soc_is_s3c2410());
s3c_pm_save_core();
/* set the irq configuration for wake */
@@ -137,14 +137,14 @@ static int s3c_pm_enter(suspend_state_t state)
/* restore the system state */
s3c_pm_restore_core();
- s3c_pm_restore_uarts();
+ s3c_pm_restore_uarts(soc_is_s3c2410());
if (!of_have_populated_dt()) {
samsung_pm_restore_gpios();
s3c_pm_restored_gpios();
}
- s3c_pm_debug_init();
+ s3c_pm_debug_init_uart();
/* check what irq (if any) restored the system */
diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/mach-s3c/pm.h
similarity index 98%
rename from arch/arm/plat-samsung/include/plat/pm.h
rename to arch/arm/mach-s3c/pm.h
index 2746137..eed61e5 100644
--- a/arch/arm/plat-samsung/include/plat/pm.h
+++ b/arch/arm/mach-s3c/pm.h
@@ -11,7 +11,7 @@
* management
*/
-#include <plat/pm-common.h>
+#include "pm-common.h"
struct device;
diff --git a/arch/arm/plat-samsung/include/plat/pwm-core.h b/arch/arm/mach-s3c/pwm-core.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/pwm-core.h
rename to arch/arm/mach-s3c/pwm-core.h
diff --git a/arch/arm/plat-samsung/include/plat/regs-adc.h b/arch/arm/mach-s3c/regs-adc.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/regs-adc.h
rename to arch/arm/mach-s3c/regs-adc.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h b/arch/arm/mach-s3c/regs-clock-s3c24xx.h
similarity index 98%
rename from arch/arm/mach-s3c24xx/include/mach/regs-clock.h
rename to arch/arm/mach-s3c/regs-clock-s3c24xx.h
index 7ca3dd4..933ddb5 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h
+++ b/arch/arm/mach-s3c/regs-clock-s3c24xx.h
@@ -9,6 +9,8 @@
#ifndef __ASM_ARM_REGS_CLOCK
#define __ASM_ARM_REGS_CLOCK
+#include "map.h"
+
#define S3C2410_CLKREG(x) ((x) + S3C24XX_VA_CLKPWR)
#define S3C2410_PLLVAL(_m,_p,_s) ((_m) << 12 | ((_p) << 4) | ((_s)))
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-clock.h b/arch/arm/mach-s3c/regs-clock-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/regs-clock.h
rename to arch/arm/mach-s3c/regs-clock-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-clock.h b/arch/arm/mach-s3c/regs-clock.h
new file mode 100644
index 0000000..7df31f2
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-clock.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-clock-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-clock-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/regs-dsc.h b/arch/arm/mach-s3c/regs-dsc-s3c24xx.h
similarity index 76%
rename from arch/arm/mach-s3c24xx/regs-dsc.h
rename to arch/arm/mach-s3c/regs-dsc-s3c24xx.h
index b500636..8b8b572 100644
--- a/arch/arm/mach-s3c24xx/regs-dsc.h
+++ b/arch/arm/mach-s3c/regs-dsc-s3c24xx.h
@@ -7,8 +7,8 @@
*/
-#ifndef __ASM_ARCH_REGS_DSC_H
-#define __ASM_ARCH_REGS_DSC_H __FILE__
+#ifndef __ASM_ARCH_REGS_DSC_S3C24XX_H
+#define __ASM_ARCH_REGS_DSC_S3C24XX_H __FILE__
/* S3C2412 */
#define S3C2412_DSC0 S3C2410_GPIOREG(0xdc)
@@ -18,5 +18,5 @@
#define S3C2440_DSC0 S3C2410_GPIOREG(0xc4)
#define S3C2440_DSC1 S3C2410_GPIOREG(0xc8)
-#endif /* __ASM_ARCH_REGS_DSC_H */
+#endif /* __ASM_ARCH_REGS_DSC_S3C24XX_H */
diff --git a/arch/arm/mach-s3c64xx/regs-gpio-memport.h b/arch/arm/mach-s3c/regs-gpio-memport-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-gpio-memport.h
rename to arch/arm/mach-s3c/regs-gpio-memport-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio-s3c24xx.h
similarity index 99%
rename from arch/arm/mach-s3c24xx/include/mach/regs-gpio.h
rename to arch/arm/mach-s3c/regs-gpio-s3c24xx.h
index 594e967..9a7e262 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h
+++ b/arch/arm/mach-s3c/regs-gpio-s3c24xx.h
@@ -10,6 +10,8 @@
#ifndef __ASM_ARCH_REGS_GPIO_H
#define __ASM_ARCH_REGS_GPIO_H
+#include "map-s3c.h"
+
#define S3C24XX_MISCCR S3C24XX_GPIOREG2(0x80)
/* general configuration options */
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/regs-gpio.h
rename to arch/arm/mach-s3c/regs-gpio-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio.h
new file mode 100644
index 0000000..0d41cb7
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-gpio.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-gpio-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-gpio-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h b/arch/arm/mach-s3c/regs-irq-s3c24xx.h
similarity index 97%
rename from arch/arm/mach-s3c24xx/include/mach/regs-irq.h
rename to arch/arm/mach-s3c/regs-irq-s3c24xx.h
index 8d8e669..c0b97b2 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h
+++ b/arch/arm/mach-s3c/regs-irq-s3c24xx.h
@@ -8,6 +8,8 @@
#ifndef ___ASM_ARCH_REGS_IRQ_H
#define ___ASM_ARCH_REGS_IRQ_H
+#include "map-s3c.h"
+
/* interrupt controller */
#define S3C2410_IRQREG(x) ((x) + S3C24XX_VA_IRQ)
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-irq.h b/arch/arm/mach-s3c/regs-irq-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/include/mach/regs-irq.h
rename to arch/arm/mach-s3c/regs-irq-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-irq.h b/arch/arm/mach-s3c/regs-irq.h
new file mode 100644
index 0000000..57f0dda
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-irq.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-irq-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-irq-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/regs-irqtype.h b/arch/arm/mach-s3c/regs-irqtype.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/regs-irqtype.h
rename to arch/arm/mach-s3c/regs-irqtype.h
diff --git a/arch/arm/mach-s3c24xx/regs-mem.h b/arch/arm/mach-s3c/regs-mem-s3c24xx.h
similarity index 97%
rename from arch/arm/mach-s3c24xx/regs-mem.h
rename to arch/arm/mach-s3c/regs-mem-s3c24xx.h
index 2f3bc48..8fed34a 100644
--- a/arch/arm/mach-s3c24xx/regs-mem.h
+++ b/arch/arm/mach-s3c/regs-mem-s3c24xx.h
@@ -9,6 +9,8 @@
#ifndef __ARCH_ARM_MACH_S3C24XX_REGS_MEM_H
#define __ARCH_ARM_MACH_S3C24XX_REGS_MEM_H __FILE__
+#include "map-s3c.h"
+
#define S3C2410_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x))
#define S3C2410_BWSCON S3C2410_MEMREG(0x00)
diff --git a/arch/arm/mach-s3c64xx/regs-modem.h b/arch/arm/mach-s3c/regs-modem-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-modem.h
rename to arch/arm/mach-s3c/regs-modem-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h b/arch/arm/mach-s3c/regs-s3c2443-clock.h
similarity index 81%
rename from arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h
rename to arch/arm/mach-s3c/regs-s3c2443-clock.h
index 6bf9246..b3b670d 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h
+++ b/arch/arm/mach-s3c/regs-s3c2443-clock.h
@@ -10,6 +10,9 @@
#ifndef __ASM_ARM_REGS_S3C2443_CLOCK
#define __ASM_ARM_REGS_S3C2443_CLOCK
+#include <linux/delay.h>
+#include "map-s3c.h"
+
#define S3C2443_CLKREG(x) ((x) + S3C24XX_VA_CLKPWR)
#define S3C2443_PLLCON_MDIVSHIFT 16
@@ -184,5 +187,52 @@ s3c2443_get_epll(unsigned int pllval, unsigned int baseclk)
return (unsigned int)fvco;
}
+static inline void s3c_hsudc_init_phy(void)
+{
+ u32 cfg;
+
+ cfg = readl(S3C2443_PWRCFG) | S3C2443_PWRCFG_USBPHY;
+ writel(cfg, S3C2443_PWRCFG);
+
+ cfg = readl(S3C2443_URSTCON);
+ cfg |= (S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
+ writel(cfg, S3C2443_URSTCON);
+ mdelay(1);
+
+ cfg = readl(S3C2443_URSTCON);
+ cfg &= ~(S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
+ writel(cfg, S3C2443_URSTCON);
+
+ cfg = readl(S3C2443_PHYCTRL);
+ cfg &= ~(S3C2443_PHYCTRL_CLKSEL | S3C2443_PHYCTRL_DSPORT);
+ cfg |= (S3C2443_PHYCTRL_EXTCLK | S3C2443_PHYCTRL_PLLSEL);
+ writel(cfg, S3C2443_PHYCTRL);
+
+ cfg = readl(S3C2443_PHYPWR);
+ cfg &= ~(S3C2443_PHYPWR_FSUSPEND | S3C2443_PHYPWR_PLL_PWRDN |
+ S3C2443_PHYPWR_XO_ON | S3C2443_PHYPWR_PLL_REFCLK |
+ S3C2443_PHYPWR_ANALOG_PD);
+ cfg |= S3C2443_PHYPWR_COMMON_ON;
+ writel(cfg, S3C2443_PHYPWR);
+
+ cfg = readl(S3C2443_UCLKCON);
+ cfg |= (S3C2443_UCLKCON_DETECT_VBUS | S3C2443_UCLKCON_FUNC_CLKEN |
+ S3C2443_UCLKCON_TCLKEN);
+ writel(cfg, S3C2443_UCLKCON);
+}
+
+static inline void s3c_hsudc_uninit_phy(void)
+{
+ u32 cfg;
+
+ cfg = readl(S3C2443_PWRCFG) & ~S3C2443_PWRCFG_USBPHY;
+ writel(cfg, S3C2443_PWRCFG);
+
+ writel(S3C2443_PHYPWR_FSUSPEND, S3C2443_PHYPWR);
+
+ cfg = readl(S3C2443_UCLKCON) & ~S3C2443_UCLKCON_FUNC_CLKEN;
+ writel(cfg, S3C2443_UCLKCON);
+}
+
#endif /* __ASM_ARM_REGS_S3C2443_CLOCK */
diff --git a/arch/arm/mach-s3c64xx/regs-srom.h b/arch/arm/mach-s3c/regs-srom-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-srom.h
rename to arch/arm/mach-s3c/regs-srom-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-sys.h b/arch/arm/mach-s3c/regs-sys-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-sys.h
rename to arch/arm/mach-s3c/regs-sys-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-syscon-power.h b/arch/arm/mach-s3c/regs-syscon-power-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-syscon-power.h
rename to arch/arm/mach-s3c/regs-syscon-power-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-usb-hsotg-phy.h b/arch/arm/mach-s3c/regs-usb-hsotg-phy-s3c64xx.h
similarity index 100%
rename from arch/arm/mach-s3c64xx/regs-usb-hsotg-phy.h
rename to arch/arm/mach-s3c/regs-usb-hsotg-phy-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h b/arch/arm/mach-s3c/rtc-core-s3c24xx.h
similarity index 80%
rename from arch/arm/mach-s3c24xx/include/mach/rtc-core.h
rename to arch/arm/mach-s3c/rtc-core-s3c24xx.h
index 8851033..e7258b2 100644
--- a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
+++ b/arch/arm/mach-s3c/rtc-core-s3c24xx.h
@@ -5,8 +5,8 @@
* Samsung RTC Controller core functions
*/
-#ifndef __RTC_CORE_H
-#define __RTC_CORE_H __FILE__
+#ifndef __RTC_CORE_S3C24XX_H
+#define __RTC_CORE_S3C24XX_H __FILE__
/* These functions are only for use with the core support code, such as
* the cpu specific initialisation code
@@ -20,4 +20,4 @@ static inline void s3c_rtc_setname(char *name)
s3c_device_rtc.name = name;
}
-#endif /* __RTC_CORE_H */
+#endif /* __RTC_CORE_S3C24XX_H */
diff --git a/arch/arm/mach-s3c24xx/s3c2410.c b/arch/arm/mach-s3c/s3c2410.c
similarity index 88%
rename from arch/arm/mach-s3c24xx/s3c2410.c
rename to arch/arm/mach-s3c/s3c2410.c
index 21fd540..4d39d99 100644
--- a/arch/arm/mach-s3c24xx/s3c2410.c
+++ b/arch/arm/mach-s3c/s3c2410.c
@@ -25,28 +25,27 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
#include <asm/irq.h>
#include <asm/system_misc.h>
-#include <plat/cpu-freq.h>
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
-#include "common.h"
+#include "s3c24xx.h"
/* Initial IO mappings */
-static struct map_desc s3c2410_iodesc[] __initdata = {
+static struct map_desc s3c2410_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(CLKPWR),
IODESC_ENT(TIMER),
IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/s3c2412-power.h b/arch/arm/mach-s3c/s3c2412-power.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/s3c2412-power.h
rename to arch/arm/mach-s3c/s3c2412-power.h
diff --git a/arch/arm/mach-s3c24xx/s3c2412.c b/arch/arm/mach-s3c/s3c2412.c
similarity index 91%
rename from arch/arm/mach-s3c24xx/s3c2412.c
rename to arch/arm/mach-s3c/s3c2412.c
index 8fe4d46..0b1ca78 100644
--- a/arch/arm/mach-s3c24xx/s3c2412.c
+++ b/arch/arm/mach-s3c/s3c2412.c
@@ -29,19 +29,17 @@
#include <asm/irq.h>
#include <asm/system_misc.h>
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
+#include "map.h"
+#include "regs-clock.h"
+#include "regs-gpio.h"
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/regs-spi.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
-#include "common.h"
-#include "nand-core.h"
-#include "regs-dsc.h"
+#include "s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "regs-dsc-s3c24xx.h"
#include "s3c2412-power.h"
#ifndef CONFIG_CPU_S3C2412_ONLY
@@ -57,7 +55,7 @@ static inline void s3c2412_init_gpio2(void)
/* Initial IO mappings */
-static struct map_desc s3c2412_iodesc[] __initdata = {
+static struct map_desc s3c2412_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(CLKPWR),
IODESC_ENT(TIMER),
IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h b/arch/arm/mach-s3c/s3c2412.h
similarity index 96%
rename from arch/arm/mach-s3c24xx/include/mach/s3c2412.h
rename to arch/arm/mach-s3c/s3c2412.h
index 4ff83f9..ed09a0e 100644
--- a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
+++ b/arch/arm/mach-s3c/s3c2412.h
@@ -8,6 +8,8 @@
#ifndef __ARCH_ARM_MACH_S3C24XX_S3C2412_H
#define __ARCH_ARM_MACH_S3C24XX_S3C2412_H __FILE__
+#include "map-s3c.h"
+
#define S3C2412_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x))
#define S3C2412_EBIREG(x) (S3C2412_VA_EBI + (x))
diff --git a/arch/arm/mach-s3c24xx/s3c2416.c b/arch/arm/mach-s3c/s3c2416.c
similarity index 84%
rename from arch/arm/mach-s3c24xx/s3c2416.c
rename to arch/arm/mach-s3c/s3c2416.c
index 9514196..126e6ed 100644
--- a/arch/arm/mach-s3c24xx/s3c2416.c
+++ b/arch/arm/mach-s3c/s3c2416.c
@@ -26,32 +26,32 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/system_misc.h>
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/rtc-core.h>
+#include "regs-s3c2443-clock.h"
+#include "rtc-core-s3c24xx.h"
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/sdhci.h>
-#include <plat/pm.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "devs.h"
+#include "cpu.h"
+#include "sdhci.h"
+#include "pm.h"
-#include <plat/iic-core.h>
-#include <plat/adc-core.h>
+#include "iic-core.h"
+#include "adc-core.h"
-#include "common.h"
-#include "fb-core.h"
-#include "nand-core.h"
-#include "spi-core.h"
+#include "s3c24xx.h"
+#include "fb-core-s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "spi-core-s3c24xx.h"
-static struct map_desc s3c2416_iodesc[] __initdata = {
+static struct map_desc s3c2416_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(WATCHDOG),
IODESC_ENT(CLKPWR),
IODESC_ENT(TIMER),
diff --git a/arch/arm/mach-s3c24xx/s3c2440.c b/arch/arm/mach-s3c/s3c2440.c
similarity index 85%
rename from arch/arm/mach-s3c24xx/s3c2440.c
rename to arch/arm/mach-s3c/s3c2440.c
index 451d985..c6cdee4 100644
--- a/arch/arm/mach-s3c24xx/s3c2440.c
+++ b/arch/arm/mach-s3c/s3c2440.c
@@ -23,19 +23,18 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
#include <asm/irq.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "gpio-samsung.h"
-#include "common.h"
+#include "s3c24xx.h"
static struct device s3c2440_dev = {
.bus = &s3c2440_subsys,
diff --git a/arch/arm/mach-s3c24xx/s3c2442.c b/arch/arm/mach-s3c/s3c2442.c
similarity index 82%
rename from arch/arm/mach-s3c24xx/s3c2442.c
rename to arch/arm/mach-s3c/s3c2442.c
index 432d683..0c0e30b 100644
--- a/arch/arm/mach-s3c24xx/s3c2442.c
+++ b/arch/arm/mach-s3c/s3c2442.c
@@ -21,21 +21,20 @@
#include <linux/clk.h>
#include <linux/io.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
#include <linux/atomic.h>
#include <asm/irq.h>
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "gpio-samsung.h"
-#include "common.h"
+#include "s3c24xx.h"
static struct device s3c2442_dev = {
.bus = &s3c2442_subsys,
diff --git a/arch/arm/mach-s3c24xx/s3c2443.c b/arch/arm/mach-s3c/s3c2443.c
similarity index 83%
rename from arch/arm/mach-s3c24xx/s3c2443.c
rename to arch/arm/mach-s3c/s3c2443.c
index 4cbeb74..08f9101 100644
--- a/arch/arm/mach-s3c24xx/s3c2443.c
+++ b/arch/arm/mach-s3c/s3c2443.c
@@ -23,26 +23,28 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
+#include <mach/irqs.h>
#include <asm/irq.h>
#include <asm/system_misc.h>
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/rtc-core.h>
+#include "regs-s3c2443-clock.h"
+#include "rtc-core-s3c24xx.h"
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc-core.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "devs.h"
+#include "cpu.h"
+#include "adc-core.h"
-#include "fb-core.h"
-#include "nand-core.h"
-#include "spi-core.h"
+#include "s3c24xx.h"
+#include "fb-core-s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "spi-core-s3c24xx.h"
-static struct map_desc s3c2443_iodesc[] __initdata = {
+static struct map_desc s3c2443_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(WATCHDOG),
IODESC_ENT(CLKPWR),
IODESC_ENT(TIMER),
diff --git a/arch/arm/mach-s3c24xx/s3c244x.c b/arch/arm/mach-s3c/s3c244x.c
similarity index 89%
rename from arch/arm/mach-s3c24xx/s3c244x.c
rename to arch/arm/mach-s3c/s3c244x.c
index a75f588..95df349 100644
--- a/arch/arm/mach-s3c24xx/s3c244x.c
+++ b/arch/arm/mach-s3c/s3c244x.c
@@ -25,23 +25,21 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
+#include "map.h"
#include <asm/irq.h>
-#include <plat/cpu-freq.h>
+#include "regs-clock.h"
+#include "regs-gpio.h"
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "regs-dsc-s3c24xx.h"
-#include "common.h"
-#include "nand-core.h"
-#include "regs-dsc.h"
-
-static struct map_desc s3c244x_iodesc[] __initdata = {
+static struct map_desc s3c244x_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(CLKPWR),
IODESC_ENT(TIMER),
IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c/s3c24xx.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/common.c
rename to arch/arm/mach-s3c/s3c24xx.c
index 3dc029c..ccfed48 100644
--- a/arch/arm/mach-s3c24xx/common.c
+++ b/arch/arm/mach-s3c/s3c24xx.c
@@ -17,11 +17,14 @@
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/io.h>
+#include <linux/platform_data/clk-s3c2410.h>
#include <linux/platform_data/dma-s3c24xx.h>
#include <linux/dmaengine.h>
+#include <linux/clk/samsung.h>
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
+#include "hardware-s3c24xx.h"
+#include "map.h"
+#include "regs-clock.h"
#include <asm/irq.h>
#include <asm/cacheflush.h>
#include <asm/system_info.h>
@@ -30,15 +33,14 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/dma.h>
+#include "regs-gpio.h"
+#include "dma-s3c24xx.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/cpu-freq.h>
-#include <plat/pwm-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pwm-core.h"
-#include "common.h"
+#include "s3c24xx.h"
/* table of supported CPUs */
@@ -137,7 +139,7 @@ static struct cpu_table cpu_ids[] __initdata = {
/* minimal IO mapping */
-static struct map_desc s3c_iodesc[] __initdata = {
+static struct map_desc s3c_iodesc[] __initdata __maybe_unused = {
IODESC_ENT(GPIO),
IODESC_ENT(IRQ),
IODESC_ENT(MEMCTRL),
@@ -220,13 +222,13 @@ void __init s3c24xx_init_io(struct map_desc *mach_desc, int size)
samsung_pwm_set_platdata(&s3c24xx_pwm_variant);
}
-void __init samsung_set_timer_source(unsigned int event, unsigned int source)
+void __init s3c24xx_set_timer_source(unsigned int event, unsigned int source)
{
s3c24xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
s3c24xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
}
-void __init samsung_timer_init(void)
+void __init s3c24xx_timer_init(void)
{
unsigned int timer_irqs[SAMSUNG_PWM_NUM] = {
IRQ_TIMER0, IRQ_TIMER1, IRQ_TIMER2, IRQ_TIMER3, IRQ_TIMER4,
@@ -662,10 +664,17 @@ static struct resource s3c2410_dclk_resource[] = {
[0] = DEFINE_RES_MEM(0x56000084, 0x4),
};
+static struct s3c2410_clk_platform_data s3c_clk_platform_data = {
+ .modify_misccr = s3c2410_modify_misccr,
+};
+
struct platform_device s3c2410_device_dclk = {
.name = "s3c2410-dclk",
.id = 0,
.num_resources = ARRAY_SIZE(s3c2410_dclk_resource),
.resource = s3c2410_dclk_resource,
+ .dev = {
+ .platform_data = &s3c_clk_platform_data,
+ },
};
#endif
diff --git a/arch/arm/mach-s3c24xx/common.h b/arch/arm/mach-s3c/s3c24xx.h
similarity index 84%
rename from arch/arm/mach-s3c24xx/common.h
rename to arch/arm/mach-s3c/s3c24xx.h
index d087b20..5848bef 100644
--- a/arch/arm/mach-s3c24xx/common.h
+++ b/arch/arm/mach-s3c/s3c24xx.h
@@ -10,6 +10,7 @@
#define __ARCH_ARM_MACH_S3C24XX_COMMON_H __FILE__
#include <linux/reboot.h>
+#include <mach/irqs.h>
struct s3c2410_uartcfg;
@@ -108,19 +109,16 @@ extern struct platform_device s3c2443_device_dma;
extern struct platform_device s3c2410_device_dclk;
-#ifdef CONFIG_S3C2410_COMMON_CLK
-void __init s3c2410_common_clk_init(struct device_node *np, unsigned long xti_f,
- int current_soc,
- void __iomem *reg_base);
-#endif
-#ifdef CONFIG_S3C2412_COMMON_CLK
-void __init s3c2412_common_clk_init(struct device_node *np, unsigned long xti_f,
- unsigned long ext_f, void __iomem *reg_base);
-#endif
-#ifdef CONFIG_S3C2443_COMMON_CLK
-void __init s3c2443_common_clk_init(struct device_node *np, unsigned long xti_f,
- int current_soc,
- void __iomem *reg_base);
-#endif
+enum s3c24xx_timer_mode {
+ S3C24XX_PWM0,
+ S3C24XX_PWM1,
+ S3C24XX_PWM2,
+ S3C24XX_PWM3,
+ S3C24XX_PWM4,
+};
+
+extern void __init s3c24xx_set_timer_source(enum s3c24xx_timer_mode event,
+ enum s3c24xx_timer_mode source);
+extern void __init s3c24xx_timer_init(void);
#endif /* __ARCH_ARM_MACH_S3C24XX_COMMON_H */
diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c/s3c6400.c
similarity index 88%
rename from arch/arm/mach-s3c64xx/s3c6400.c
rename to arch/arm/mach-s3c/s3c6400.c
index 545eea7..802f4fb 100644
--- a/arch/arm/mach-s3c64xx/s3c6400.c
+++ b/arch/arm/mach-s3c/s3c6400.c
@@ -26,19 +26,17 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
-#include <plat/cpu-freq.h>
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/sdhci.h>
-#include <plat/iic-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "sdhci.h"
+#include "iic-core.h"
-#include "common.h"
-#include "onenand-core.h"
+#include "s3c64xx.h"
+#include "onenand-core-s3c64xx.h"
void __init s3c6400_map_io(void)
{
diff --git a/arch/arm/mach-s3c64xx/s3c6410.c b/arch/arm/mach-s3c/s3c6410.c
similarity index 86%
rename from arch/arm/mach-s3c64xx/s3c6410.c
rename to arch/arm/mach-s3c/s3c6410.c
index 47e04e0..dae17d5 100644
--- a/arch/arm/mach-s3c64xx/s3c6410.c
+++ b/arch/arm/mach-s3c/s3c6410.c
@@ -27,21 +27,20 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
-#include <plat/cpu-freq.h>
-#include <mach/regs-clock.h>
+#include <linux/soc/samsung/s3c-pm.h>
+#include "regs-clock.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/sdhci.h>
-#include <plat/adc-core.h>
-#include <plat/iic-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "sdhci.h"
+#include "adc-core.h"
+#include "iic-core.h"
-#include "ata-core.h"
-#include "common.h"
-#include "onenand-core.h"
+#include "ata-core-s3c64xx.h"
+#include "s3c64xx.h"
+#include "onenand-core-s3c64xx.h"
void __init s3c6410_map_io(void)
{
diff --git a/arch/arm/mach-s3c64xx/common.c b/arch/arm/mach-s3c/s3c64xx.c
similarity index 90%
rename from arch/arm/mach-s3c64xx/common.c
rename to arch/arm/mach-s3c/s3c64xx.c
index 13e9107..4dfb648 100644
--- a/arch/arm/mach-s3c64xx/common.c
+++ b/arch/arm/mach-s3c/s3c64xx.c
@@ -24,6 +24,7 @@
#include <linux/platform_device.h>
#include <linux/reboot.h>
#include <linux/io.h>
+#include <linux/clk/samsung.h>
#include <linux/dma-mapping.h>
#include <linux/irq.h>
#include <linux/gpio.h>
@@ -34,22 +35,19 @@
#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <mach/map.h>
+#include "map.h"
#include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pwm-core.h>
-#include <plat/regs-irqtype.h>
-
-#include "common.h"
-#include "irq-uart.h"
-#include "watchdog-reset.h"
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "gpio-cfg.h"
+#include "pwm-core.h"
+#include "regs-irqtype.h"
+#include "s3c64xx.h"
+#include "irq-uart-s3c64xx.h"
/* External clock frequency */
static unsigned long xtal_f __ro_after_init = 12000000;
@@ -97,7 +95,12 @@ static struct cpu_table cpu_ids[] __initdata = {
/* minimal IO mapping */
-/* see notes on uart map in arch/arm/mach-s3c64xx/include/mach/debug-macro.S */
+/*
+ * note, for the boot process to work we have to keep the UART
+ * virtual address aligned to an 1MiB boundary for the L1
+ * mapping the head code makes. We keep the UART virtual address
+ * aligned and add in the offset when we load the value here.
+ */
#define UART_OFFS (S3C_PA_UART & 0xfffff)
static struct map_desc s3c_iodesc[] __initdata = {
@@ -170,13 +173,13 @@ static struct samsung_pwm_variant s3c64xx_pwm_variant = {
.tclk_mask = (1 << 7) | (1 << 6) | (1 << 5),
};
-void __init samsung_set_timer_source(unsigned int event, unsigned int source)
+void __init s3c64xx_set_timer_source(unsigned int event, unsigned int source)
{
s3c64xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
s3c64xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
}
-void __init samsung_timer_init(void)
+void __init s3c64xx_timer_init(void)
{
unsigned int timer_irqs[SAMSUNG_PWM_NUM] = {
IRQ_TIMER0_VIC, IRQ_TIMER1_VIC, IRQ_TIMER2_VIC,
@@ -228,13 +231,7 @@ core_initcall(s3c64xx_dev_init);
void __init s3c64xx_init_irq(u32 vic0_valid, u32 vic1_valid)
{
- /*
- * FIXME: there is no better place to put this at the moment
- * (s3c64xx_clk_init needs ioremap and must happen before init_time
- * samsung_wdt_reset_init needs clocks)
- */
s3c64xx_clk_init(NULL, xtal_f, xusbxti_f, soc_is_s3c6400(), S3C_VA_SYS);
- samsung_wdt_reset_init(S3C_VA_WATCHDOG);
printk(KERN_DEBUG "%s: initialising interrupts\n", __func__);
@@ -428,12 +425,3 @@ static int __init s3c64xx_init_irq_eint(void)
return 0;
}
arch_initcall(s3c64xx_init_irq_eint);
-
-void s3c64xx_restart(enum reboot_mode mode, const char *cmd)
-{
- if (mode != REBOOT_SOFT)
- samsung_wdt_reset();
-
- /* if all else fails, or mode was for soft, jump to 0 */
- soft_restart(0);
-}
diff --git a/arch/arm/mach-s3c64xx/common.h b/arch/arm/mach-s3c/s3c64xx.h
similarity index 79%
rename from arch/arm/mach-s3c64xx/common.h
rename to arch/arm/mach-s3c/s3c64xx.h
index 0367088..92258e4 100644
--- a/arch/arm/mach-s3c64xx/common.h
+++ b/arch/arm/mach-s3c/s3c64xx.h
@@ -19,11 +19,7 @@
void s3c64xx_init_irq(u32 vic0, u32 vic1);
void s3c64xx_init_io(struct map_desc *mach_desc, int size);
-void s3c64xx_restart(enum reboot_mode mode, const char *cmd);
-
struct device_node;
-void s3c64xx_clk_init(struct device_node *np, unsigned long xtal_f,
- unsigned long xusbxti_f, bool is_s3c6400, void __iomem *reg_base);
void s3c64xx_set_xtal_freq(unsigned long freq);
void s3c64xx_set_xusbxti_freq(unsigned long freq);
@@ -54,4 +50,17 @@ extern struct pl08x_platform_data s3c64xx_dma0_plat_data;
extern struct pl08x_platform_data s3c64xx_dma1_plat_data;
#endif
+/* Samsung HR-Timer Clock mode */
+enum s3c64xx_timer_mode {
+ S3C64XX_PWM0,
+ S3C64XX_PWM1,
+ S3C64XX_PWM2,
+ S3C64XX_PWM3,
+ S3C64XX_PWM4,
+};
+
+extern void __init s3c64xx_set_timer_source(enum s3c64xx_timer_mode event,
+ enum s3c64xx_timer_mode source);
+extern void __init s3c64xx_timer_init(void);
+
#endif /* __ARCH_ARM_MACH_S3C64XX_COMMON_H */
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/mach-s3c/sdhci.h
similarity index 99%
rename from arch/arm/plat-samsung/include/plat/sdhci.h
rename to arch/arm/mach-s3c/sdhci.h
index 5731e42..9f9d419 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/mach-s3c/sdhci.h
@@ -15,7 +15,7 @@
#define __PLAT_S3C_SDHCI_H __FILE__
#include <linux/platform_data/mmc-sdhci-s3c.h>
-#include <plat/devs.h>
+#include "devs.h"
/* s3c_sdhci_set_platdata() - common helper for setting SDHCI platform data
* @pd: The default platform data for this device.
diff --git a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c b/arch/arm/mach-s3c/setup-fb-24bpp-s3c64xx.c
similarity index 85%
rename from arch/arm/mach-s3c64xx/setup-fb-24bpp.c
rename to arch/arm/mach-s3c/setup-fb-24bpp-s3c64xx.c
index 2c7178b..cfa34b5 100644
--- a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c
+++ b/arch/arm/mach-s3c/setup-fb-24bpp-s3c64xx.c
@@ -12,9 +12,9 @@
#include <linux/fb.h>
#include <linux/gpio.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "fb.h"
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
void s3c64xx_fb_gpio_setup_24bpp(void)
{
diff --git a/arch/arm/mach-s3c24xx/setup-i2c.c b/arch/arm/mach-s3c/setup-i2c-s3c24xx.c
similarity index 79%
rename from arch/arm/mach-s3c24xx/setup-i2c.c
rename to arch/arm/mach-s3c/setup-i2c-s3c24xx.c
index 1a01d44..0d88366 100644
--- a/arch/arm/mach-s3c24xx/setup-i2c.c
+++ b/arch/arm/mach-s3c/setup-i2c-s3c24xx.c
@@ -10,11 +10,11 @@
struct platform_device;
-#include <plat/gpio-cfg.h>
#include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+
+#include "gpio-cfg.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
{
diff --git a/arch/arm/mach-s3c64xx/setup-i2c0.c b/arch/arm/mach-s3c/setup-i2c0-s3c64xx.c
similarity index 89%
rename from arch/arm/mach-s3c64xx/setup-i2c0.c
rename to arch/arm/mach-s3c/setup-i2c0-s3c64xx.c
index 552eb50..a6ef8d2 100644
--- a/arch/arm/mach-s3c64xx/setup-i2c0.c
+++ b/arch/arm/mach-s3c/setup-i2c0-s3c64xx.c
@@ -14,8 +14,8 @@
struct platform_device; /* don't need the contents */
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
{
diff --git a/arch/arm/mach-s3c64xx/setup-i2c1.c b/arch/arm/mach-s3c/setup-i2c1-s3c64xx.c
similarity index 89%
rename from arch/arm/mach-s3c64xx/setup-i2c1.c
rename to arch/arm/mach-s3c/setup-i2c1-s3c64xx.c
index d231f0f..0fe3736 100644
--- a/arch/arm/mach-s3c64xx/setup-i2c1.c
+++ b/arch/arm/mach-s3c/setup-i2c1-s3c64xx.c
@@ -14,8 +14,8 @@
struct platform_device; /* don't need the contents */
#include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
void s3c_i2c1_cfg_gpio(struct platform_device *dev)
{
diff --git a/arch/arm/mach-s3c64xx/setup-ide.c b/arch/arm/mach-s3c/setup-ide-s3c64xx.c
similarity index 89%
rename from arch/arm/mach-s3c64xx/setup-ide.c
rename to arch/arm/mach-s3c/setup-ide-s3c64xx.c
index 810139a..f11f2b0 100644
--- a/arch/arm/mach-s3c64xx/setup-ide.c
+++ b/arch/arm/mach-s3c/setup-ide-s3c64xx.c
@@ -9,12 +9,13 @@
#include <linux/gpio.h>
#include <linux/io.h>
-#include <mach/map.h>
-#include <mach/regs-clock.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
#include <linux/platform_data/ata-samsung_cf.h>
+#include "map.h"
+#include "regs-clock.h"
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
+
void s3c64xx_ide_setup_gpio(void)
{
u32 reg;
diff --git a/arch/arm/mach-s3c64xx/setup-keypad.c b/arch/arm/mach-s3c/setup-keypad-s3c64xx.c
similarity index 86%
rename from arch/arm/mach-s3c64xx/setup-keypad.c
rename to arch/arm/mach-s3c/setup-keypad-s3c64xx.c
index 3519610..8463ad3 100644
--- a/arch/arm/mach-s3c64xx/setup-keypad.c
+++ b/arch/arm/mach-s3c/setup-keypad-s3c64xx.c
@@ -6,9 +6,9 @@
// GPIO configuration for S3C64XX KeyPad device
#include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <plat/keypad.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "keypad.h"
+#include "gpio-samsung.h"
void samsung_keypad_cfg_gpio(unsigned int rows, unsigned int cols)
{
diff --git a/arch/arm/mach-s3c24xx/setup-sdhci-gpio.c b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c24xx.c
similarity index 88%
rename from arch/arm/mach-s3c24xx/setup-sdhci-gpio.c
rename to arch/arm/mach-s3c/setup-sdhci-gpio-s3c24xx.c
index 218346a..02131b3 100644
--- a/arch/arm/mach-s3c24xx/setup-sdhci-gpio.c
+++ b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c24xx.c
@@ -14,9 +14,10 @@
#include <linux/io.h>
#include <linux/gpio.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-#include <plat/gpio-cfg.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
+#include "sdhci.h"
void s3c2416_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
{
diff --git a/arch/arm/mach-s3c64xx/setup-sdhci-gpio.c b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c64xx.c
similarity index 94%
rename from arch/arm/mach-s3c64xx/setup-sdhci-gpio.c
rename to arch/arm/mach-s3c/setup-sdhci-gpio-s3c64xx.c
index 138455a..646ff94 100644
--- a/arch/arm/mach-s3c64xx/setup-sdhci-gpio.c
+++ b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c64xx.c
@@ -13,9 +13,9 @@
#include <linux/io.h>
#include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <plat/sdhci.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "sdhci.h"
+#include "gpio-samsung.h"
void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
{
diff --git a/arch/arm/mach-s3c24xx/setup-spi.c b/arch/arm/mach-s3c/setup-spi-s3c24xx.c
similarity index 84%
rename from arch/arm/mach-s3c24xx/setup-spi.c
rename to arch/arm/mach-s3c/setup-spi-s3c24xx.c
index 6c2b96a..93fa1bb 100644
--- a/arch/arm/mach-s3c24xx/setup-spi.c
+++ b/arch/arm/mach-s3c/setup-spi-s3c24xx.c
@@ -8,10 +8,10 @@
#include <linux/gpio.h>
#include <linux/platform_device.h>
-#include <plat/gpio-cfg.h>
+#include "gpio-cfg.h"
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
#ifdef CONFIG_S3C64XX_DEV_SPI0
int s3c64xx_spi0_cfg_gpio(void)
diff --git a/arch/arm/mach-s3c64xx/setup-spi.c b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
similarity index 83%
rename from arch/arm/mach-s3c64xx/setup-spi.c
rename to arch/arm/mach-s3c/setup-spi-s3c64xx.c
index 39dfae1..efcf78d 100644
--- a/arch/arm/mach-s3c64xx/setup-spi.c
+++ b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
@@ -4,8 +4,9 @@
// http://www.samsung.com/
#include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/spi-s3c64xx.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
#ifdef CONFIG_S3C64XX_DEV_SPI0
int s3c64xx_spi0_cfg_gpio(void)
diff --git a/arch/arm/mach-s3c24xx/setup-ts.c b/arch/arm/mach-s3c/setup-ts-s3c24xx.c
similarity index 80%
rename from arch/arm/mach-s3c24xx/setup-ts.c
rename to arch/arm/mach-s3c/setup-ts-s3c24xx.c
index 53a14d4..57363ea 100644
--- a/arch/arm/mach-s3c24xx/setup-ts.c
+++ b/arch/arm/mach-s3c/setup-ts-s3c24xx.c
@@ -10,12 +10,14 @@
struct platform_device; /* don't need the contents */
-#include <plat/gpio-cfg.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
/**
* s3c24xx_ts_cfg_gpio - configure gpio for s3c2410 systems
+ * @dev: Device to configure GPIO for (ignored)
*
* Configure the GPIO for the S3C2410 system, where we have external FETs
* connected to the device (later systems such as the S3C2440 integrate
diff --git a/arch/arm/mach-s3c64xx/setup-usb-phy.c b/arch/arm/mach-s3c/setup-usb-phy-s3c64xx.c
similarity index 91%
rename from arch/arm/mach-s3c64xx/setup-usb-phy.c
rename to arch/arm/mach-s3c/setup-usb-phy-s3c64xx.c
index d6b0e3b..500d105 100644
--- a/arch/arm/mach-s3c64xx/setup-usb-phy.c
+++ b/arch/arm/mach-s3c/setup-usb-phy-s3c64xx.c
@@ -8,12 +8,12 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/platform_device.h>
-#include <mach/map.h>
-#include <plat/cpu.h>
-#include <plat/usb-phy.h>
+#include "map.h"
+#include "cpu.h"
+#include "usb-phy.h"
-#include "regs-sys.h"
-#include "regs-usb-hsotg-phy.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-usb-hsotg-phy-s3c64xx.h"
enum samsung_usb_phy_type {
USB_PHY_TYPE_DEVICE,
@@ -31,7 +31,7 @@ static int s3c_usb_otgphy_init(struct platform_device *pdev)
phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
xusbxti = clk_get(&pdev->dev, "xusbxti");
- if (xusbxti && !IS_ERR(xusbxti)) {
+ if (!IS_ERR(xusbxti)) {
switch (clk_get_rate(xusbxti)) {
case 12 * MHZ:
phyclk |= S3C_PHYCLK_CLKSEL_12M;
diff --git a/arch/arm/mach-s3c24xx/simtec-audio.c b/arch/arm/mach-s3c/simtec-audio.c
similarity index 86%
rename from arch/arm/mach-s3c24xx/simtec-audio.c
rename to arch/arm/mach-s3c/simtec-audio.c
index 12e17f8..487485b 100644
--- a/arch/arm/mach-s3c24xx/simtec-audio.c
+++ b/arch/arm/mach-s3c/simtec-audio.c
@@ -12,11 +12,12 @@
#include <linux/device.h>
#include <linux/io.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
#include <linux/platform_data/asoc-s3c24xx_simtec.h>
-#include <plat/devs.h>
+#include "devs.h"
#include "bast.h"
#include "simtec.h"
@@ -65,6 +66,10 @@ int __init simtec_audio_add(const char *name, bool has_lr_routing,
if (has_lr_routing)
simtec_audio_platdata.startup = simtec_audio_startup_lrroute;
+ /* Configure the I2S pins (GPE0...GPE4) in correct mode */
+ s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+ S3C_GPIO_PULL_NONE);
+
platform_device_register(&s3c_device_iis);
platform_device_register(&simtec_audio_dev);
return 0;
diff --git a/arch/arm/mach-s3c24xx/simtec-nor.c b/arch/arm/mach-s3c/simtec-nor.c
similarity index 98%
rename from arch/arm/mach-s3c24xx/simtec-nor.c
rename to arch/arm/mach-s3c/simtec-nor.c
index 26b1849..a6fba05 100644
--- a/arch/arm/mach-s3c24xx/simtec-nor.c
+++ b/arch/arm/mach-s3c/simtec-nor.c
@@ -21,7 +21,7 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/map.h>
+#include "map.h"
#include "bast.h"
#include "simtec.h"
diff --git a/arch/arm/mach-s3c24xx/simtec-pm.c b/arch/arm/mach-s3c/simtec-pm.c
similarity index 90%
rename from arch/arm/mach-s3c24xx/simtec-pm.c
rename to arch/arm/mach-s3c/simtec-pm.c
index c19074d..490256a 100644
--- a/arch/arm/mach-s3c24xx/simtec-pm.c
+++ b/arch/arm/mach-s3c/simtec-pm.c
@@ -19,16 +19,14 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/hardware.h>
-
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
+#include "map.h"
+#include "regs-gpio.h"
#include <asm/mach-types.h>
-#include <plat/pm.h>
+#include "pm.h"
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
#define COPYRIGHT ", Copyright 2005 Simtec Electronics"
diff --git a/arch/arm/mach-s3c24xx/simtec-usb.c b/arch/arm/mach-s3c/simtec-usb.c
similarity index 96%
rename from arch/arm/mach-s3c24xx/simtec-usb.c
rename to arch/arm/mach-s3c/simtec-usb.c
index dc1016f..18fe064 100644
--- a/arch/arm/mach-s3c24xx/simtec-usb.c
+++ b/arch/arm/mach-s3c/simtec-usb.c
@@ -23,12 +23,12 @@
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
+#include <mach/irqs.h>
#include <asm/irq.h>
#include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/devs.h>
+#include "devs.h"
#include "bast.h"
#include "simtec.h"
diff --git a/arch/arm/mach-s3c24xx/simtec.h b/arch/arm/mach-s3c/simtec.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/simtec.h
rename to arch/arm/mach-s3c/simtec.h
diff --git a/arch/arm/mach-s3c24xx/sleep-s3c2410.S b/arch/arm/mach-s3c/sleep-s3c2410.S
similarity index 90%
rename from arch/arm/mach-s3c24xx/sleep-s3c2410.S
rename to arch/arm/mach-s3c/sleep-s3c2410.S
index 659f9eff..04aded9 100644
--- a/arch/arm/mach-s3c24xx/sleep-s3c2410.S
+++ b/arch/arm/mach-s3c/sleep-s3c2410.S
@@ -13,13 +13,12 @@
#include <linux/linkage.h>
#include <linux/serial_s3c.h>
#include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
/* s3c2410_cpu_suspend
*
diff --git a/arch/arm/mach-s3c24xx/sleep-s3c2412.S b/arch/arm/mach-s3c/sleep-s3c2412.S
similarity index 93%
rename from arch/arm/mach-s3c24xx/sleep-s3c2412.S
rename to arch/arm/mach-s3c/sleep-s3c2412.S
index c373f1c..b4b6173 100644
--- a/arch/arm/mach-s3c24xx/sleep-s3c2412.S
+++ b/arch/arm/mach-s3c/sleep-s3c2412.S
@@ -8,10 +8,9 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
-#include <mach/regs-irq.h>
+#include "regs-irq.h"
.text
diff --git a/arch/arm/mach-s3c24xx/sleep.S b/arch/arm/mach-s3c/sleep-s3c24xx.S
similarity index 92%
rename from arch/arm/mach-s3c24xx/sleep.S
rename to arch/arm/mach-s3c/sleep-s3c24xx.S
index f0f11ad..4b2af91 100644
--- a/arch/arm/mach-s3c24xx/sleep.S
+++ b/arch/arm/mach-s3c/sleep-s3c24xx.S
@@ -13,11 +13,10 @@
#include <linux/linkage.h>
#include <linux/serial_s3c.h>
#include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
/*
* S3C24XX_DEBUG_RESUME is dangerous if your bootloader does not
diff --git a/arch/arm/mach-s3c64xx/sleep.S b/arch/arm/mach-s3c/sleep-s3c64xx.S
similarity index 96%
rename from arch/arm/mach-s3c64xx/sleep.S
rename to arch/arm/mach-s3c/sleep-s3c64xx.S
index 39e16a0..739e53f 100644
--- a/arch/arm/mach-s3c64xx/sleep.S
+++ b/arch/arm/mach-s3c/sleep-s3c64xx.S
@@ -11,12 +11,12 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <mach/map.h>
+#include "map.h"
#undef S3C64XX_VA_GPIO
#define S3C64XX_VA_GPIO (0x0)
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
#define LL_UART (S3C_PA_UART + (0x400 * CONFIG_S3C_LOWLEVEL_UART_PORT))
diff --git a/arch/arm/mach-s3c24xx/spi-core.h b/arch/arm/mach-s3c/spi-core-s3c24xx.h
similarity index 81%
rename from arch/arm/mach-s3c24xx/spi-core.h
rename to arch/arm/mach-s3c/spi-core-s3c24xx.h
index 1048fac..0576674 100644
--- a/arch/arm/mach-s3c24xx/spi-core.h
+++ b/arch/arm/mach-s3c/spi-core-s3c24xx.h
@@ -3,8 +3,8 @@
* Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
*/
-#ifndef __PLAT_S3C_SPI_CORE_H
-#define __PLAT_S3C_SPI_CORE_H
+#ifndef __PLAT_S3C_SPI_CORE_S3C24XX_H
+#define __PLAT_S3C_SPI_CORE_S3C24XX_H
/* These functions are only for use with the core support code, such as
* the cpu specific initialisation code
@@ -24,4 +24,4 @@ static inline void s3c24xx_spi_setname(char *name)
#endif
}
-#endif /* __PLAT_S3C_SPI_CORE_H */
+#endif /* __PLAT_S3C_SPI_CORE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/usb-phy.h b/arch/arm/mach-s3c/usb-phy.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/usb-phy.h
rename to arch/arm/mach-s3c/usb-phy.h
diff --git a/arch/arm/mach-s3c24xx/vr1000.h b/arch/arm/mach-s3c/vr1000.h
similarity index 100%
rename from arch/arm/mach-s3c24xx/vr1000.h
rename to arch/arm/mach-s3c/vr1000.h
diff --git a/arch/arm/plat-samsung/wakeup-mask.c b/arch/arm/mach-s3c/wakeup-mask.c
similarity index 94%
rename from arch/arm/plat-samsung/wakeup-mask.c
rename to arch/arm/mach-s3c/wakeup-mask.c
index 24f96fb..b490e75 100644
--- a/arch/arm/plat-samsung/wakeup-mask.c
+++ b/arch/arm/mach-s3c/wakeup-mask.c
@@ -11,8 +11,8 @@
#include <linux/irq.h>
#include <linux/io.h>
-#include <plat/wakeup-mask.h>
-#include <plat/pm.h>
+#include "wakeup-mask.h"
+#include "pm.h"
void samsung_sync_wakemask(void __iomem *reg,
const struct samsung_wakeup_mask *mask, int nr_mask)
diff --git a/arch/arm/plat-samsung/include/plat/wakeup-mask.h b/arch/arm/mach-s3c/wakeup-mask.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/wakeup-mask.h
rename to arch/arm/mach-s3c/wakeup-mask.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/fb.h b/arch/arm/mach-s3c24xx/include/mach/fb.h
deleted file mode 100644
index 4e539cb..0000000
--- a/arch/arm/mach-s3c24xx/include/mach/fb.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <plat/fb-s3c2410.h>
diff --git a/arch/arm/mach-s3c24xx/include/mach/hardware.h b/arch/arm/mach-s3c24xx/include/mach/hardware.h
deleted file mode 100644
index f28ac6c..0000000
--- a/arch/arm/mach-s3c24xx/include/mach/hardware.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - hardware
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#ifndef __ASSEMBLY__
-
-extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
-
-#endif /* __ASSEMBLY__ */
-
-#include <linux/sizes.h>
-#include <mach/map.h>
-
-#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/io.h b/arch/arm/mach-s3c24xx/include/mach/io.h
deleted file mode 100644
index f960e6d..0000000
--- a/arch/arm/mach-s3c24xx/include/mach/io.h
+++ /dev/null
@@ -1,212 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-s3c2410/include/mach/io.h
- * from arch/arm/mach-rpc/include/mach/io.h
- *
- * Copyright (C) 1997 Russell King
- * (C) 2003 Simtec Electronics
-*/
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <mach/hardware.h>
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses. PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1. ARM addresses are above A28
- * and are translated to the start of IO. Note that all addresses are
- * not shifted left!
- */
-
-#define __PORT_PCIO(x) ((x) < (1<<28))
-
-#define PCIO_BASE (S3C24XX_VA_ISA_WORD)
-#define PCIO_BASE_b (S3C24XX_VA_ISA_BYTE)
-#define PCIO_BASE_w (S3C24XX_VA_ISA_WORD)
-#define PCIO_BASE_l (S3C24XX_VA_ISA_WORD)
-/*
- * Dynamic IO functions - let the compiler
- * optimize the expressions
- */
-
-#define DECLARE_DYN_OUT(sz,fnsuffix,instr) \
-static inline void __out##fnsuffix (unsigned int val, unsigned int port) \
-{ \
- unsigned long temp; \
- __asm__ __volatile__( \
- "cmp %2, #(1<<28)\n\t" \
- "mov %0, %2\n\t" \
- "addcc %0, %0, %3\n\t" \
- "str" instr " %1, [%0, #0 ] @ out" #fnsuffix \
- : "=&r" (temp) \
- : "r" (val), "r" (port), "Ir" (PCIO_BASE_##fnsuffix) \
- : "cc"); \
-}
-
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr) \
-static inline unsigned sz __in##fnsuffix (unsigned int port) \
-{ \
- unsigned long temp, value; \
- __asm__ __volatile__( \
- "cmp %2, #(1<<28)\n\t" \
- "mov %0, %2\n\t" \
- "addcc %0, %0, %3\n\t" \
- "ldr" instr " %1, [%0, #0 ] @ in" #fnsuffix \
- : "=&r" (temp), "=r" (value) \
- : "r" (port), "Ir" (PCIO_BASE_##fnsuffix) \
- : "cc"); \
- return (unsigned sz)value; \
-}
-
-static inline void __iomem *__ioaddr (unsigned long port)
-{
- return __PORT_PCIO(port) ? (PCIO_BASE + port) : (void __iomem *)port;
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr) \
- DECLARE_DYN_IN(sz,fnsuffix,instr) \
- DECLARE_DYN_OUT(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"h")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
- *
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
- */
-#define __outbc(value,port) \
-({ \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (PCIO_BASE), "Jr" ((port))); \
- else \
- __asm__ __volatile__( \
- "strb %0, [%1, #0] @ outbc" \
- : : "r" (value), "r" ((port))); \
-})
-
-#define __inbc(port) \
-({ \
- unsigned char result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port))); \
- else \
- __asm__ __volatile__( \
- "ldrb %0, [%1, #0] @ inbc" \
- : "=r" (result) : "r" ((port))); \
- result; \
-})
-
-#define __outwc(value,port) \
-({ \
- unsigned long v = value; \
- if (__PORT_PCIO((port))) { \
- if ((port) < 256 && (port) > -256) \
- __asm__ __volatile__( \
- "strh %0, [%1, %2] @ outwc" \
- : : "r" (v), "r" (PCIO_BASE), "Jr" ((port))); \
- else if ((port) > 0) \
- __asm__ __volatile__( \
- "strh %0, [%1, %2] @ outwc" \
- : : "r" (v), \
- "r" (PCIO_BASE + ((port) & ~0xff)), \
- "Jr" (((port) & 0xff))); \
- else \
- __asm__ __volatile__( \
- "strh %0, [%1, #0] @ outwc" \
- : : "r" (v), \
- "r" (PCIO_BASE + (port))); \
- } else \
- __asm__ __volatile__( \
- "strh %0, [%1, #0] @ outwc" \
- : : "r" (v), "r" ((port))); \
-})
-
-#define __inwc(port) \
-({ \
- unsigned short result; \
- if (__PORT_PCIO((port))) { \
- if ((port) < 256 && (port) > -256 ) \
- __asm__ __volatile__( \
- "ldrh %0, [%1, %2] @ inwc" \
- : "=r" (result) \
- : "r" (PCIO_BASE), \
- "Jr" ((port))); \
- else if ((port) > 0) \
- __asm__ __volatile__( \
- "ldrh %0, [%1, %2] @ inwc" \
- : "=r" (result) \
- : "r" (PCIO_BASE + ((port) & ~0xff)), \
- "Jr" (((port) & 0xff))); \
- else \
- __asm__ __volatile__( \
- "ldrh %0, [%1, #0] @ inwc" \
- : "=r" (result) \
- : "r" (PCIO_BASE + ((port)))); \
- } else \
- __asm__ __volatile__( \
- "ldrh %0, [%1, #0] @ inwc" \
- : "=r" (result) : "r" ((port))); \
- result; \
-})
-
-#define __outlc(value,port) \
-({ \
- unsigned long v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (v), "r" (PCIO_BASE), "Jr" ((port))); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, #0] @ outlc" \
- : : "r" (v), "r" ((port))); \
-})
-
-#define __inlc(port) \
-({ \
- unsigned long result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port))); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, #0] @ inlc" \
- : "=r" (result) : "r" ((port))); \
- result; \
-})
-
-#define __ioaddrc(port) ((__PORT_PCIO(port) ? PCIO_BASE + (port) : (void __iomem *)0 + (port)))
-
-#define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p))
-#define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p))
-#define inl(p) (__builtin_constant_p((p)) ? __inlc(p) : __inl(p))
-#define outb(v,p) (__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-#define __ioaddr(p) (__builtin_constant_p((p)) ? __ioaddr(p) : __ioaddrc(p))
-
-#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
-#define insl(p,d,l) __raw_readsl(__ioaddr(p),d,l)
-
-#define outsb(p,d,l) __raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l) __raw_writesw(__ioaddr(p),d,l)
-#define outsl(p,d,l) __raw_writesl(__ioaddr(p),d,l)
-
-#endif
diff --git a/arch/arm/mach-s3c24xx/setup-camif.c b/arch/arm/mach-s3c24xx/setup-camif.c
deleted file mode 100644
index 2b262fa..0000000
--- a/arch/arm/mach-s3c24xx/setup-camif.c
+++ /dev/null
@@ -1,67 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (C) 2012 Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
-//
-// Helper functions for S3C24XX/S3C64XX SoC series CAMIF driver
-
-#include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
-
-/* Number of camera port pins, without FIELD */
-#define S3C_CAMIF_NUM_GPIOS 13
-
-/* Default camera port configuration helpers. */
-
-static void camif_get_gpios(int *gpio_start, int *gpio_reset)
-{
-#ifdef CONFIG_ARCH_S3C24XX
- *gpio_start = S3C2410_GPJ(0);
- *gpio_reset = S3C2410_GPJ(12);
-#else
- /* s3c64xx */
- *gpio_start = S3C64XX_GPF(0);
- *gpio_reset = S3C64XX_GPF(3);
-#endif
-}
-
-int s3c_camif_gpio_get(void)
-{
- int gpio_start, gpio_reset;
- int ret, i;
-
- camif_get_gpios(&gpio_start, &gpio_reset);
-
- for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
- int gpio = gpio_start + i;
-
- if (gpio == gpio_reset)
- continue;
-
- ret = gpio_request(gpio, "camif");
- if (!ret)
- ret = s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
- if (ret) {
- pr_err("failed to configure GPIO %d\n", gpio);
- for (--i; i >= 0; i--)
- gpio_free(gpio--);
- return ret;
- }
- s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
- }
-
- return 0;
-}
-
-void s3c_camif_gpio_put(void)
-{
- int i, gpio_start, gpio_reset;
-
- camif_get_gpios(&gpio_start, &gpio_reset);
-
- for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
- int gpio = gpio_start + i;
- if (gpio != gpio_reset)
- gpio_free(gpio);
- }
-}
diff --git a/arch/arm/mach-s3c64xx/Makefile b/arch/arm/mach-s3c64xx/Makefile
deleted file mode 100644
index 8caeb4a..0000000
--- a/arch/arm/mach-s3c64xx/Makefile
+++ /dev/null
@@ -1,62 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# Copyright 2008 Openmoko, Inc.
-# Copyright 2008 Simtec Electronics
-
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
-asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
-
-# PM
-
-obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_PM_SLEEP) += sleep.o
-obj-$(CONFIG_CPU_IDLE) += cpuidle.o
-
-ifdef CONFIG_SAMSUNG_ATAGS
-
-obj-$(CONFIG_PM_SLEEP) += irq-pm.o
-
-# Core
-
-obj-y += common.o
-obj-$(CONFIG_CPU_S3C6400) += s3c6400.o
-obj-$(CONFIG_CPU_S3C6410) += s3c6410.o
-
-# DMA support
-
-obj-$(CONFIG_S3C64XX_PL080) += pl080.o
-
-# Device support
-
-obj-y += dev-uart.o
-obj-y += dev-audio.o
-
-# Device setup
-
-obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o
-obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o
-obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o
-obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide.o
-obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
-obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o
-obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy.o
-
-obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT) += dev-backlight.o
-
-# Machine support
-
-obj-$(CONFIG_MACH_ANW6410) += mach-anw6410.o
-obj-$(CONFIG_MACH_HMT) += mach-hmt.o
-obj-$(CONFIG_MACH_MINI6410) += mach-mini6410.o
-obj-$(CONFIG_MACH_NCP) += mach-ncp.o
-obj-$(CONFIG_MACH_REAL6410) += mach-real6410.o
-obj-$(CONFIG_MACH_SMARTQ) += mach-smartq.o
-obj-$(CONFIG_MACH_SMARTQ5) += mach-smartq5.o
-obj-$(CONFIG_MACH_SMARTQ7) += mach-smartq7.o
-obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o
-obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o
-obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
-endif
-
-obj-$(CONFIG_MACH_S3C64XX_DT) += mach-s3c64xx-dt.o
diff --git a/arch/arm/mach-s3c64xx/include/mach/hardware.h b/arch/arm/mach-s3c64xx/include/mach/hardware.h
deleted file mode 100644
index c4ed359..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/hardware.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/* linux/arch/arm/mach-s3c6400/include/mach/hardware.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C6400 - Hardware support
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H __FILE__
-
-/* currently nothing here, placeholder */
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s3c64xx/include/mach/pm-core.h b/arch/arm/mach-s3c64xx/include/mach/pm-core.h
deleted file mode 100644
index bbf79ed..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/pm-core.h
+++ /dev/null
@@ -1,124 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C64XX - PM core support for arch/arm/plat-s3c/pm.c
- */
-
-#ifndef __MACH_S3C64XX_PM_CORE_H
-#define __MACH_S3C64XX_PM_CORE_H __FILE__
-
-#include <linux/serial_s3c.h>
-#include <linux/delay.h>
-
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
-#include <mach/map.h>
-
-static inline void s3c_pm_debug_init_uart(void)
-{
- u32 tmp = __raw_readl(S3C_PCLK_GATE);
-
- /* As a note, since the S3C64XX UARTs generally have multiple
- * clock sources, we simply enable PCLK at the moment and hope
- * that the resume settings for the UART are suitable for the
- * use with PCLK.
- */
-
- tmp |= S3C_CLKCON_PCLK_UART0;
- tmp |= S3C_CLKCON_PCLK_UART1;
- tmp |= S3C_CLKCON_PCLK_UART2;
- tmp |= S3C_CLKCON_PCLK_UART3;
-
- __raw_writel(tmp, S3C_PCLK_GATE);
- udelay(10);
-}
-
-static inline void s3c_pm_arch_prepare_irqs(void)
-{
- /* VIC should have already been taken care of */
-
- /* clear any pending EINT0 interrupts */
- __raw_writel(__raw_readl(S3C64XX_EINT0PEND), S3C64XX_EINT0PEND);
-}
-
-static inline void s3c_pm_arch_stop_clocks(void)
-{
-}
-
-static inline void s3c_pm_arch_show_resume_irqs(void)
-{
-}
-
-/* make these defines, we currently do not have any need to change
- * the IRQ wake controls depending on the CPU we are running on */
-#ifdef CONFIG_PM_SLEEP
-#define s3c_irqwake_eintallow ((1 << 28) - 1)
-#define s3c_irqwake_intallow (~0)
-#else
-#define s3c_irqwake_eintallow 0
-#define s3c_irqwake_intallow 0
-#endif
-
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
- struct pm_uart_save *save)
-{
- u32 ucon = __raw_readl(regs + S3C2410_UCON);
- u32 ucon_clk = ucon & S3C6400_UCON_CLKMASK;
- u32 save_clk = save->ucon & S3C6400_UCON_CLKMASK;
- u32 new_ucon;
- u32 delta;
-
- /* S3C64XX UART blocks only support level interrupts, so ensure that
- * when we restore unused UART blocks we force the level interrupt
- * settigs. */
- save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
-
- /* We have a constraint on changing the clock type of the UART
- * between UCLKx and PCLK, so ensure that when we restore UCON
- * that the CLK field is correctly modified if the bootloader
- * has changed anything.
- */
- if (ucon_clk != save_clk) {
- new_ucon = save->ucon;
- delta = ucon_clk ^ save_clk;
-
- /* change from UCLKx => wrong PCLK,
- * either UCLK can be tested for by a bit-test
- * with UCLK0 */
- if (ucon_clk & S3C6400_UCON_UCLK0 &&
- !(save_clk & S3C6400_UCON_UCLK0) &&
- delta & S3C6400_UCON_PCLK2) {
- new_ucon &= ~S3C6400_UCON_UCLK0;
- } else if (delta == S3C6400_UCON_PCLK2) {
- /* as an precaution, don't change from
- * PCLK2 => PCLK or vice-versa */
- new_ucon ^= S3C6400_UCON_PCLK2;
- }
-
- S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
- ucon, new_ucon, save->ucon);
- save->ucon = new_ucon;
- }
-}
-
-static inline void s3c_pm_restored_gpios(void)
-{
- /* ensure sleep mode has been cleared from the system */
-
- __raw_writel(0, S3C64XX_SLPEN);
-}
-
-static inline void samsung_pm_saved_gpios(void)
-{
- /* turn on the sleep mode and keep it there, as it seems that during
- * suspend the xCON registers get re-set and thus you can end up with
- * problems between going to sleep and resuming.
- */
-
- __raw_writel(S3C64XX_SLPEN_USE_xSLP, S3C64XX_SLPEN);
-}
-#endif /* __MACH_S3C64XX_PM_CORE_H */
diff --git a/arch/arm/mach-s3c64xx/watchdog-reset.h b/arch/arm/mach-s3c64xx/watchdog-reset.h
deleted file mode 100644
index 1042d6c..0000000
--- a/arch/arm/mach-s3c64xx/watchdog-reset.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - System define for arch_reset() function
- */
-
-#ifndef __PLAT_SAMSUNG_WATCHDOG_RESET_H
-#define __PLAT_SAMSUNG_WATCHDOG_RESET_H
-
-extern void samsung_wdt_reset(void);
-extern void samsung_wdt_reset_of_init(void);
-extern void samsung_wdt_reset_init(void __iomem *base);
-
-#endif /* __PLAT_SAMSUNG_WATCHDOG_RESET_H */
diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 03984a7..95d4e82 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -14,10 +14,10 @@
select COMMON_CLK_SAMSUNG
select GPIOLIB
select HAVE_S3C2410_I2C if I2C
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select PINCTRL
select PINCTRL_EXYNOS
+ select SOC_SAMSUNG
help
Samsung S5PV210/S5PC110 series based systems
diff --git a/arch/arm/mach-s5pv210/Makefile b/arch/arm/mach-s5pv210/Makefile
index e7b551e..aa0a1f0 100644
--- a/arch/arm/mach-s5pv210/Makefile
+++ b/arch/arm/mach-s5pv210/Makefile
@@ -3,12 +3,5 @@
# Copyright (c) 2010 Samsung Electronics Co., Ltd.
# http://www.samsung.com/
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/arch/arm/plat-samsung/include
-
-# Core
-
obj-$(CONFIG_PM_SLEEP) += pm.o sleep.o
-
-# machine support
-
obj-y += s5pv210.o
diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c
index b336df0..d59c094 100644
--- a/arch/arm/mach-s5pv210/pm.c
+++ b/arch/arm/mach-s5pv210/pm.c
@@ -13,15 +13,56 @@
#include <linux/suspend.h>
#include <linux/syscore_ops.h>
#include <linux/io.h>
+#include <linux/soc/samsung/s3c-pm.h>
#include <asm/cacheflush.h>
#include <asm/suspend.h>
-#include <plat/pm-common.h>
-
#include "common.h"
#include "regs-clock.h"
+/* helper functions to save and restore register state */
+struct sleep_save {
+ void __iomem *reg;
+ unsigned long val;
+};
+
+#define SAVE_ITEM(x) \
+ { .reg = (x) }
+
+/**
+ * s3c_pm_do_save() - save a set of registers for restoration on resume.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Run through the list of registers given, saving their contents in the
+ * array for later restoration when we wakeup.
+ */
+static void s3c_pm_do_save(struct sleep_save *ptr, int count)
+{
+ for (; count > 0; count--, ptr++) {
+ ptr->val = readl_relaxed(ptr->reg);
+ S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val);
+ }
+}
+
+/**
+ * s3c_pm_do_restore() - restore register values from the save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Restore the register values saved from s3c_pm_do_save().
+ *
+ * WARNING: Do not put any debug in here that may effect memory or use
+ * peripherals, as things may be changing!
+*/
+
+static void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count)
+{
+ for (; count > 0; count--, ptr++)
+ writel_relaxed(ptr->val, ptr->reg);
+}
+
static struct sleep_save s5pv210_core_save[] = {
/* Clock ETC */
SAVE_ITEM(S5P_MDNIE_SEL),
@@ -99,8 +140,6 @@ static int s5pv210_suspend_enter(suspend_state_t state)
u32 eint_wakeup_mask = s5pv210_read_eint_wakeup_mask();
int ret;
- s3c_pm_debug_init();
-
S3C_PMDBG("%s: suspending the system...\n", __func__);
S3C_PMDBG("%s: wakeup masks: %08x,%08x\n", __func__,
@@ -113,7 +152,7 @@ static int s5pv210_suspend_enter(suspend_state_t state)
return -EINVAL;
}
- s3c_pm_save_uarts();
+ s3c_pm_save_uarts(false);
s5pv210_pm_prepare();
flush_cache_all();
s3c_pm_check_store();
@@ -122,7 +161,7 @@ static int s5pv210_suspend_enter(suspend_state_t state)
if (ret)
return ret;
- s3c_pm_restore_uarts();
+ s3c_pm_restore_uarts(false);
S3C_PMDBG("%s: wakeup stat: %08x\n", __func__,
__raw_readl(S5P_WAKEUP_STAT));
diff --git a/arch/arm/mach-s5pv210/regs-clock.h b/arch/arm/mach-s5pv210/regs-clock.h
index 2a35c83..9cad230 100644
--- a/arch/arm/mach-s5pv210/regs-clock.h
+++ b/arch/arm/mach-s5pv210/regs-clock.h
@@ -9,7 +9,9 @@
#ifndef __ASM_ARCH_REGS_CLOCK_H
#define __ASM_ARCH_REGS_CLOCK_H __FILE__
-#include <plat/map-base.h>
+#define S3C_ADDR_BASE 0xF6000000
+#define S3C_ADDR(x) ((void __iomem __force *)S3C_ADDR_BASE + (x))
+#define S3C_VA_SYS S3C_ADDR(0x00100000)
#define S5P_CLKREG(x) (S3C_VA_SYS + (x))
diff --git a/arch/arm/mach-s5pv210/s5pv210.c b/arch/arm/mach-s5pv210/s5pv210.c
index 868f9c2..a21ed3b 100644
--- a/arch/arm/mach-s5pv210/s5pv210.c
+++ b/arch/arm/mach-s5pv210/s5pv210.c
@@ -13,8 +13,6 @@
#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <plat/map-base.h>
-
#include "common.h"
#include "regs-clock.h"
diff --git a/arch/arm/mach-shmobile/rcar-gen2.h b/arch/arm/mach-shmobile/rcar-gen2.h
index 4777fff..af9dbd6 100644
--- a/arch/arm/mach-shmobile/rcar-gen2.h
+++ b/arch/arm/mach-shmobile/rcar-gen2.h
@@ -2,8 +2,6 @@
#ifndef __ASM_RCAR_GEN2_H__
#define __ASM_RCAR_GEN2_H__
-void rcar_gen2_timer_init(void);
-void rcar_gen2_reserve(void);
void rcar_gen2_pm_init(void);
#endif /* __ASM_RCAR_GEN2_H__ */
diff --git a/arch/arm/mach-shmobile/setup-rcar-gen2.c b/arch/arm/mach-shmobile/setup-rcar-gen2.c
index e00f5b3..d42d934 100644
--- a/arch/arm/mach-shmobile/setup-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/setup-rcar-gen2.c
@@ -59,7 +59,7 @@ static unsigned int __init get_extal_freq(void)
#define CNTCR 0
#define CNTFID0 0x20
-void __init rcar_gen2_timer_init(void)
+static void __init rcar_gen2_timer_init(void)
{
bool need_update = true;
void __iomem *base;
@@ -174,7 +174,7 @@ static int __init rcar_gen2_scan_mem(unsigned long node, const char *uname,
return 0;
}
-void __init rcar_gen2_reserve(void)
+static void __init rcar_gen2_reserve(void)
{
struct memory_reserve_config mrc;
diff --git a/arch/arm/mach-stm32/Makefile.boot b/arch/arm/mach-stm32/Makefile.boot
index cec195d..5dde732 100644
--- a/arch/arm/mach-stm32/Makefile.boot
+++ b/arch/arm/mach-stm32/Makefile.boot
@@ -1,4 +1,4 @@
# SPDX-License-Identifier: GPL-2.0-only
# Empty file waiting for deletion once Makefile.boot isn't needed any more.
# Patch waits for application at
-# http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
+# https://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
deleted file mode 100644
index 614240d..0000000
--- a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
+++ /dev/null
@@ -1,68 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2004 Arnaud Patard <arnaud.patard@rtp-net.org>
- *
- * Inspired by pxafb.h
-*/
-
-#ifndef __ASM_PLAT_FB_S3C2410_H
-#define __ASM_PLAT_FB_S3C2410_H __FILE__
-
-struct s3c2410fb_hw {
- unsigned long lcdcon1;
- unsigned long lcdcon2;
- unsigned long lcdcon3;
- unsigned long lcdcon4;
- unsigned long lcdcon5;
-};
-
-/* LCD description */
-struct s3c2410fb_display {
- /* LCD type */
- unsigned type;
-
- /* Screen size */
- unsigned short width;
- unsigned short height;
-
- /* Screen info */
- unsigned short xres;
- unsigned short yres;
- unsigned short bpp;
-
- unsigned pixclock; /* pixclock in picoseconds */
- unsigned short left_margin; /* value in pixels (TFT) or HCLKs (STN) */
- unsigned short right_margin; /* value in pixels (TFT) or HCLKs (STN) */
- unsigned short hsync_len; /* value in pixels (TFT) or HCLKs (STN) */
- unsigned short upper_margin; /* value in lines (TFT) or 0 (STN) */
- unsigned short lower_margin; /* value in lines (TFT) or 0 (STN) */
- unsigned short vsync_len; /* value in lines (TFT) or 0 (STN) */
-
- /* lcd configuration registers */
- unsigned long lcdcon5;
-};
-
-struct s3c2410fb_mach_info {
-
- struct s3c2410fb_display *displays; /* attached displays info */
- unsigned num_displays; /* number of defined displays */
- unsigned default_display;
-
- /* GPIOs */
-
- unsigned long gpcup;
- unsigned long gpcup_mask;
- unsigned long gpccon;
- unsigned long gpccon_mask;
- unsigned long gpdup;
- unsigned long gpdup_mask;
- unsigned long gpdcon;
- unsigned long gpdcon_mask;
-
- /* lpc3600 control register */
- unsigned long lpcsel;
-};
-
-extern void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *);
-
-#endif /* __ASM_PLAT_FB_S3C2410_H */
diff --git a/arch/arm/plat-samsung/include/plat/pm-common.h b/arch/arm/plat-samsung/include/plat/pm-common.h
deleted file mode 100644
index 1268bae..0000000
--- a/arch/arm/plat-samsung/include/plat/pm-common.h
+++ /dev/null
@@ -1,107 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) 2013 Samsung Electronics Co., Ltd.
- * Tomasz Figa <t.figa@samsung.com>
- * Copyright (c) 2004 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- * Written by Ben Dooks, <ben@simtec.co.uk>
- */
-
-#ifndef __PLAT_SAMSUNG_PM_COMMON_H
-#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
-
-#include <linux/irq.h>
-
-/* sleep save info */
-
-/**
- * struct sleep_save - save information for shared peripherals.
- * @reg: Pointer to the register to save.
- * @val: Holder for the value saved from reg.
- *
- * This describes a list of registers which is used by the pm core and
- * other subsystem to save and restore register values over suspend.
- */
-struct sleep_save {
- void __iomem *reg;
- unsigned long val;
-};
-
-#define SAVE_ITEM(x) \
- { .reg = (x) }
-
-/* helper functions to save/restore lists of registers. */
-
-extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
-
-/* PM debug functions */
-
-/**
- * struct pm_uart_save - save block for core UART
- * @ulcon: Save value for S3C2410_ULCON
- * @ucon: Save value for S3C2410_UCON
- * @ufcon: Save value for S3C2410_UFCON
- * @umcon: Save value for S3C2410_UMCON
- * @ubrdiv: Save value for S3C2410_UBRDIV
- *
- * Save block for UART registers to be held over sleep and restored if they
- * are needed (say by debug).
-*/
-struct pm_uart_save {
- u32 ulcon;
- u32 ucon;
- u32 ufcon;
- u32 umcon;
- u32 ubrdiv;
- u32 udivslot;
-};
-
-#ifdef CONFIG_SAMSUNG_PM_DEBUG
-/**
- * s3c_pm_dbg() - low level debug function for use in suspend/resume.
- * @msg: The message to print.
- *
- * This function is used mainly to debug the resume process before the system
- * can rely on printk/console output. It uses the low-level debugging output
- * routine printascii() to do its work.
- */
-extern void s3c_pm_dbg(const char *msg, ...);
-
-/**
- * s3c_pm_debug_init() - suspend/resume low level debug initialization.
- * @base: Virtual base of UART to use for suspend/resume debugging.
- *
- * This function needs to be called before S3C_PMDBG() can be used, to set up
- * UART port base address and configuration.
- */
-extern void s3c_pm_debug_init(void);
-
-#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
-
-extern void s3c_pm_save_uarts(void);
-extern void s3c_pm_restore_uarts(void);
-#else
-#define S3C_PMDBG(fmt...) pr_debug(fmt)
-#define s3c_pm_debug_init() do { } while (0)
-
-static inline void s3c_pm_save_uarts(void) { }
-static inline void s3c_pm_restore_uarts(void) { }
-#endif
-
-/* suspend memory checking */
-
-#ifdef CONFIG_SAMSUNG_PM_CHECK
-extern void s3c_pm_check_prepare(void);
-extern void s3c_pm_check_restore(void);
-extern void s3c_pm_check_cleanup(void);
-extern void s3c_pm_check_store(void);
-#else
-#define s3c_pm_check_prepare() do { } while (0)
-#define s3c_pm_check_restore() do { } while (0)
-#define s3c_pm_check_cleanup() do { } while (0)
-#define s3c_pm_check_store() do { } while (0)
-#endif
-
-#endif
diff --git a/arch/arm/plat-samsung/include/plat/samsung-time.h b/arch/arm/plat-samsung/include/plat/samsung-time.h
deleted file mode 100644
index 32ab086..0000000
--- a/arch/arm/plat-samsung/include/plat/samsung-time.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright 2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com/
- *
- * Header file for samsung s3c and s5p time support
- */
-
-#ifndef __ASM_PLAT_SAMSUNG_TIME_H
-#define __ASM_PLAT_SAMSUNG_TIME_H __FILE__
-
-/* Samsung HR-Timer Clock mode */
-enum samsung_timer_mode {
- SAMSUNG_PWM0,
- SAMSUNG_PWM1,
- SAMSUNG_PWM2,
- SAMSUNG_PWM3,
- SAMSUNG_PWM4,
-};
-
-extern void __init samsung_set_timer_source(enum samsung_timer_mode event,
- enum samsung_timer_mode source);
-
-extern void __init samsung_timer_init(void);
-
-#endif /* __ASM_PLAT_SAMSUNG_TIME_H */
diff --git a/arch/arm/plat-samsung/watchdog-reset.c b/arch/arm/plat-samsung/watchdog-reset.c
deleted file mode 100644
index 71d85ff..0000000
--- a/arch/arm/plat-samsung/watchdog-reset.c
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (c) 2008 Simtec Electronics
-// Ben Dooks <ben@simtec.co.uk>
-//
-// Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
-//
-// Watchdog reset support for Samsung SoCs.
-
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#define S3C2410_WTCON 0x00
-#define S3C2410_WTDAT 0x04
-#define S3C2410_WTCNT 0x08
-
-#define S3C2410_WTCON_ENABLE (1 << 5)
-#define S3C2410_WTCON_DIV16 (0 << 3)
-#define S3C2410_WTCON_RSTEN (1 << 0)
-#define S3C2410_WTCON_PRESCALE(x) ((x) << 8)
-
-static void __iomem *wdt_base;
-static struct clk *wdt_clock;
-
-void samsung_wdt_reset(void)
-{
- if (!wdt_base) {
- pr_err("%s: wdt reset not initialized\n", __func__);
- /* delay to allow the serial port to show the message */
- mdelay(50);
- return;
- }
-
- if (!IS_ERR(wdt_clock))
- clk_prepare_enable(wdt_clock);
-
- /* disable watchdog, to be safe */
- __raw_writel(0, wdt_base + S3C2410_WTCON);
-
- /* put initial values into count and data */
- __raw_writel(0x80, wdt_base + S3C2410_WTCNT);
- __raw_writel(0x80, wdt_base + S3C2410_WTDAT);
-
- /* set the watchdog to go and reset... */
- __raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV16 |
- S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x20),
- wdt_base + S3C2410_WTCON);
-
- /* wait for reset to assert... */
- mdelay(500);
-
- pr_err("Watchdog reset failed to assert reset\n");
-
- /* delay to allow the serial port to show the message */
- mdelay(50);
-}
-
-#ifdef CONFIG_OF
-static const struct of_device_id s3c2410_wdt_match[] = {
- { .compatible = "samsung,s3c2410-wdt" },
- { .compatible = "samsung,s3c6410-wdt" },
- {},
-};
-
-void __init samsung_wdt_reset_of_init(void)
-{
- struct device_node *np;
-
- np = of_find_matching_node(NULL, s3c2410_wdt_match);
- if (!np) {
- pr_err("%s: failed to find watchdog node\n", __func__);
- return;
- }
-
- wdt_base = of_iomap(np, 0);
- if (!wdt_base) {
- pr_err("%s: failed to map watchdog registers\n", __func__);
- return;
- }
-
- wdt_clock = of_clk_get(np, 0);
-}
-#endif
-
-void __init samsung_wdt_reset_init(void __iomem *base)
-{
- wdt_base = base;
- wdt_clock = clk_get(NULL, "watchdog");
-}
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index cd58f84..d235b27 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -80,7 +80,6 @@
select EXYNOS_CHIPID
select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
select EXYNOS_PMU
- select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select PINCTRL
select PINCTRL_EXYNOS
diff --git a/drivers/clk/imx/clk-imx27.c b/drivers/clk/imx/clk-imx27.c
index a375306..5585ded 100644
--- a/drivers/clk/imx/clk-imx27.c
+++ b/drivers/clk/imx/clk-imx27.c
@@ -181,79 +181,6 @@ static void __init _mx27_clocks_init(unsigned long fref)
imx_print_silicon_rev("i.MX27", mx27_revision());
}
-int __init mx27_clocks_init(unsigned long fref)
-{
- ccm = ioremap(MX27_CCM_BASE_ADDR, SZ_4K);
-
- _mx27_clocks_init(fref);
-
- clk_register_clkdev(clk[IMX27_CLK_UART1_IPG_GATE], "ipg", "imx21-uart.0");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.0");
- clk_register_clkdev(clk[IMX27_CLK_UART2_IPG_GATE], "ipg", "imx21-uart.1");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.1");
- clk_register_clkdev(clk[IMX27_CLK_UART3_IPG_GATE], "ipg", "imx21-uart.2");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.2");
- clk_register_clkdev(clk[IMX27_CLK_UART4_IPG_GATE], "ipg", "imx21-uart.3");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.3");
- clk_register_clkdev(clk[IMX27_CLK_UART5_IPG_GATE], "ipg", "imx21-uart.4");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.4");
- clk_register_clkdev(clk[IMX27_CLK_UART6_IPG_GATE], "ipg", "imx21-uart.5");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx21-uart.5");
- clk_register_clkdev(clk[IMX27_CLK_GPT1_IPG_GATE], "ipg", "imx-gpt.0");
- clk_register_clkdev(clk[IMX27_CLK_PER1_GATE], "per", "imx-gpt.0");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx21-mmc.0");
- clk_register_clkdev(clk[IMX27_CLK_SDHC1_IPG_GATE], "ipg", "imx21-mmc.0");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx21-mmc.1");
- clk_register_clkdev(clk[IMX27_CLK_SDHC2_IPG_GATE], "ipg", "imx21-mmc.1");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx21-mmc.2");
- clk_register_clkdev(clk[IMX27_CLK_SDHC2_IPG_GATE], "ipg", "imx21-mmc.2");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx27-cspi.0");
- clk_register_clkdev(clk[IMX27_CLK_CSPI1_IPG_GATE], "ipg", "imx27-cspi.0");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx27-cspi.1");
- clk_register_clkdev(clk[IMX27_CLK_CSPI2_IPG_GATE], "ipg", "imx27-cspi.1");
- clk_register_clkdev(clk[IMX27_CLK_PER2_GATE], "per", "imx27-cspi.2");
- clk_register_clkdev(clk[IMX27_CLK_CSPI3_IPG_GATE], "ipg", "imx27-cspi.2");
- clk_register_clkdev(clk[IMX27_CLK_PER3_GATE], "per", "imx21-fb.0");
- clk_register_clkdev(clk[IMX27_CLK_LCDC_IPG_GATE], "ipg", "imx21-fb.0");
- clk_register_clkdev(clk[IMX27_CLK_LCDC_AHB_GATE], "ahb", "imx21-fb.0");
- clk_register_clkdev(clk[IMX27_CLK_CSI_AHB_GATE], "ahb", "imx27-camera.0");
- clk_register_clkdev(clk[IMX27_CLK_PER4_GATE], "per", "imx27-camera.0");
- clk_register_clkdev(clk[IMX27_CLK_USB_DIV], "per", "imx-udc-mx27");
- clk_register_clkdev(clk[IMX27_CLK_USB_IPG_GATE], "ipg", "imx-udc-mx27");
- clk_register_clkdev(clk[IMX27_CLK_USB_AHB_GATE], "ahb", "imx-udc-mx27");
- clk_register_clkdev(clk[IMX27_CLK_USB_DIV], "per", "mxc-ehci.0");
- clk_register_clkdev(clk[IMX27_CLK_USB_IPG_GATE], "ipg", "mxc-ehci.0");
- clk_register_clkdev(clk[IMX27_CLK_USB_AHB_GATE], "ahb", "mxc-ehci.0");
- clk_register_clkdev(clk[IMX27_CLK_USB_DIV], "per", "mxc-ehci.1");
- clk_register_clkdev(clk[IMX27_CLK_USB_IPG_GATE], "ipg", "mxc-ehci.1");
- clk_register_clkdev(clk[IMX27_CLK_USB_AHB_GATE], "ahb", "mxc-ehci.1");
- clk_register_clkdev(clk[IMX27_CLK_USB_DIV], "per", "mxc-ehci.2");
- clk_register_clkdev(clk[IMX27_CLK_USB_IPG_GATE], "ipg", "mxc-ehci.2");
- clk_register_clkdev(clk[IMX27_CLK_USB_AHB_GATE], "ahb", "mxc-ehci.2");
- clk_register_clkdev(clk[IMX27_CLK_SSI1_IPG_GATE], NULL, "imx-ssi.0");
- clk_register_clkdev(clk[IMX27_CLK_SSI2_IPG_GATE], NULL, "imx-ssi.1");
- clk_register_clkdev(clk[IMX27_CLK_NFC_BAUD_GATE], NULL, "imx27-nand.0");
- clk_register_clkdev(clk[IMX27_CLK_VPU_BAUD_GATE], "per", "coda-imx27.0");
- clk_register_clkdev(clk[IMX27_CLK_VPU_AHB_GATE], "ahb", "coda-imx27.0");
- clk_register_clkdev(clk[IMX27_CLK_DMA_AHB_GATE], "ahb", "imx27-dma");
- clk_register_clkdev(clk[IMX27_CLK_DMA_IPG_GATE], "ipg", "imx27-dma");
- clk_register_clkdev(clk[IMX27_CLK_FEC_IPG_GATE], "ipg", "imx27-fec.0");
- clk_register_clkdev(clk[IMX27_CLK_FEC_AHB_GATE], "ahb", "imx27-fec.0");
- clk_register_clkdev(clk[IMX27_CLK_WDOG_IPG_GATE], NULL, "imx2-wdt.0");
- clk_register_clkdev(clk[IMX27_CLK_I2C1_IPG_GATE], NULL, "imx21-i2c.0");
- clk_register_clkdev(clk[IMX27_CLK_I2C2_IPG_GATE], NULL, "imx21-i2c.1");
- clk_register_clkdev(clk[IMX27_CLK_OWIRE_IPG_GATE], NULL, "mxc_w1.0");
- clk_register_clkdev(clk[IMX27_CLK_KPP_IPG_GATE], NULL, "imx-keypad");
- clk_register_clkdev(clk[IMX27_CLK_EMMA_AHB_GATE], "emma-ahb", "imx27-camera.0");
- clk_register_clkdev(clk[IMX27_CLK_EMMA_IPG_GATE], "emma-ipg", "imx27-camera.0");
- clk_register_clkdev(clk[IMX27_CLK_EMMA_AHB_GATE], "ahb", "m2m-emmaprp.0");
- clk_register_clkdev(clk[IMX27_CLK_EMMA_IPG_GATE], "ipg", "m2m-emmaprp.0");
-
- mxc_timer_init(MX27_GPT1_BASE_ADDR, MX27_INT_GPT1, GPT_TYPE_IMX21);
-
- return 0;
-}
-
static void __init mx27_clocks_init_dt(struct device_node *np)
{
struct device_node *refnp;
diff --git a/drivers/clk/imx/clk-imx31.c b/drivers/clk/imx/clk-imx31.c
index 4bb05e4..7b13fb5 100644
--- a/drivers/clk/imx/clk-imx31.c
+++ b/drivers/clk/imx/clk-imx31.c
@@ -132,77 +132,6 @@ static void __init _mx31_clocks_init(void __iomem *base, unsigned long fref)
clk_disable_unprepare(clk[iim_gate]);
}
-int __init mx31_clocks_init(unsigned long fref)
-{
- void __iomem *base;
-
- base = ioremap(MX31_CCM_BASE_ADDR, SZ_4K);
- if (!base)
- panic("%s: failed to map registers\n", __func__);
-
- _mx31_clocks_init(base, fref);
-
- clk_register_clkdev(clk[gpt_gate], "per", "imx-gpt.0");
- clk_register_clkdev(clk[ipg], "ipg", "imx-gpt.0");
- clk_register_clkdev(clk[cspi1_gate], NULL, "imx31-cspi.0");
- clk_register_clkdev(clk[cspi2_gate], NULL, "imx31-cspi.1");
- clk_register_clkdev(clk[cspi3_gate], NULL, "imx31-cspi.2");
- clk_register_clkdev(clk[pwm_gate], "pwm", NULL);
- clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0");
- clk_register_clkdev(clk[ckil], "ref", "imx21-rtc");
- clk_register_clkdev(clk[rtc_gate], "ipg", "imx21-rtc");
- clk_register_clkdev(clk[epit1_gate], "epit", NULL);
- clk_register_clkdev(clk[epit2_gate], "epit", NULL);
- clk_register_clkdev(clk[nfc], NULL, "imx27-nand.0");
- clk_register_clkdev(clk[ipu_gate], NULL, "ipu-core");
- clk_register_clkdev(clk[ipu_gate], NULL, "mx3_sdc_fb");
- clk_register_clkdev(clk[kpp_gate], NULL, "imx-keypad");
- clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.0");
- clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.0");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.0");
- clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.1");
- clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.1");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.1");
- clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.2");
- clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.2");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
- clk_register_clkdev(clk[usb_div_post], "per", "imx-udc-mx27");
- clk_register_clkdev(clk[usb_gate], "ahb", "imx-udc-mx27");
- clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
- clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
- /* i.mx31 has the i.mx21 type uart */
- clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.0");
- clk_register_clkdev(clk[uart2_gate], "per", "imx21-uart.1");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.1");
- clk_register_clkdev(clk[uart3_gate], "per", "imx21-uart.2");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.2");
- clk_register_clkdev(clk[uart4_gate], "per", "imx21-uart.3");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.3");
- clk_register_clkdev(clk[uart5_gate], "per", "imx21-uart.4");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.4");
- clk_register_clkdev(clk[i2c1_gate], NULL, "imx21-i2c.0");
- clk_register_clkdev(clk[i2c2_gate], NULL, "imx21-i2c.1");
- clk_register_clkdev(clk[i2c3_gate], NULL, "imx21-i2c.2");
- clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1.0");
- clk_register_clkdev(clk[sdhc1_gate], NULL, "imx31-mmc.0");
- clk_register_clkdev(clk[sdhc2_gate], NULL, "imx31-mmc.1");
- clk_register_clkdev(clk[ssi1_gate], NULL, "imx-ssi.0");
- clk_register_clkdev(clk[ssi2_gate], NULL, "imx-ssi.1");
- clk_register_clkdev(clk[firi_gate], "firi", NULL);
- clk_register_clkdev(clk[ata_gate], NULL, "pata_imx");
- clk_register_clkdev(clk[rtic_gate], "rtic", NULL);
- clk_register_clkdev(clk[rng_gate], NULL, "mxc_rnga");
- clk_register_clkdev(clk[sdma_gate], NULL, "imx31-sdma");
- clk_register_clkdev(clk[iim_gate], "iim", NULL);
-
-
- imx_register_uart_clocks(uart_clks);
- mxc_timer_init(MX31_GPT1_BASE_ADDR, MX31_INT_GPT, GPT_TYPE_IMX31);
-
- return 0;
-}
-
static void __init mx31_clocks_init_dt(struct device_node *np)
{
struct device_node *osc_np;
diff --git a/drivers/clk/imx/clk-imx35.c b/drivers/clk/imx/clk-imx35.c
index e595f55..c1df036 100644
--- a/drivers/clk/imx/clk-imx35.c
+++ b/drivers/clk/imx/clk-imx35.c
@@ -248,74 +248,6 @@ static void __init _mx35_clocks_init(void)
imx_print_silicon_rev("i.MX35", mx35_revision());
}
-int __init mx35_clocks_init(void)
-{
- _mx35_clocks_init();
-
- clk_register_clkdev(clk[pata_gate], NULL, "pata_imx");
- clk_register_clkdev(clk[can1_gate], NULL, "flexcan.0");
- clk_register_clkdev(clk[can2_gate], NULL, "flexcan.1");
- clk_register_clkdev(clk[cspi1_gate], "per", "imx35-cspi.0");
- clk_register_clkdev(clk[cspi1_gate], "ipg", "imx35-cspi.0");
- clk_register_clkdev(clk[cspi2_gate], "per", "imx35-cspi.1");
- clk_register_clkdev(clk[cspi2_gate], "ipg", "imx35-cspi.1");
- clk_register_clkdev(clk[epit1_gate], NULL, "imx-epit.0");
- clk_register_clkdev(clk[epit2_gate], NULL, "imx-epit.1");
- clk_register_clkdev(clk[esdhc1_gate], "per", "sdhci-esdhc-imx35.0");
- clk_register_clkdev(clk[ipg], "ipg", "sdhci-esdhc-imx35.0");
- clk_register_clkdev(clk[ahb], "ahb", "sdhci-esdhc-imx35.0");
- clk_register_clkdev(clk[esdhc2_gate], "per", "sdhci-esdhc-imx35.1");
- clk_register_clkdev(clk[ipg], "ipg", "sdhci-esdhc-imx35.1");
- clk_register_clkdev(clk[ahb], "ahb", "sdhci-esdhc-imx35.1");
- clk_register_clkdev(clk[esdhc3_gate], "per", "sdhci-esdhc-imx35.2");
- clk_register_clkdev(clk[ipg], "ipg", "sdhci-esdhc-imx35.2");
- clk_register_clkdev(clk[ahb], "ahb", "sdhci-esdhc-imx35.2");
- /* i.mx35 has the i.mx27 type fec */
- clk_register_clkdev(clk[fec_gate], NULL, "imx27-fec.0");
- clk_register_clkdev(clk[gpt_gate], "per", "imx-gpt.0");
- clk_register_clkdev(clk[ipg], "ipg", "imx-gpt.0");
- clk_register_clkdev(clk[i2c1_gate], NULL, "imx21-i2c.0");
- clk_register_clkdev(clk[i2c2_gate], NULL, "imx21-i2c.1");
- clk_register_clkdev(clk[i2c3_gate], NULL, "imx21-i2c.2");
- clk_register_clkdev(clk[ipu_gate], NULL, "ipu-core");
- clk_register_clkdev(clk[ipu_gate], NULL, "mx3_sdc_fb");
- clk_register_clkdev(clk[kpp_gate], NULL, "imx-keypad");
- clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1");
- clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
- clk_register_clkdev(clk[ssi1_gate], NULL, "imx-ssi.0");
- clk_register_clkdev(clk[ssi2_gate], NULL, "imx-ssi.1");
- /* i.mx35 has the i.mx21 type uart */
- clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.0");
- clk_register_clkdev(clk[uart2_gate], "per", "imx21-uart.1");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.1");
- clk_register_clkdev(clk[uart3_gate], "per", "imx21-uart.2");
- clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.2");
- /* i.mx35 has the i.mx21 type rtc */
- clk_register_clkdev(clk[ckil], "ref", "imx21-rtc");
- clk_register_clkdev(clk[rtc_gate], "ipg", "imx21-rtc");
- clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.0");
- clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.0");
- clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.1");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.1");
- clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.1");
- clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
- clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
- clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.2");
- clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
- clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
- clk_register_clkdev(clk[usbotg_gate], "ahb", "imx-udc-mx27");
- clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0");
- clk_register_clkdev(clk[nfc_div], NULL, "imx25-nand.0");
- clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
- clk_register_clkdev(clk[admux_gate], "audmux", NULL);
-
- mxc_timer_init(MX35_GPT1_BASE_ADDR, MX35_INT_GPT, GPT_TYPE_IMX31);
-
- return 0;
-}
-
static void __init mx35_clocks_init_dt(struct device_node *ccm_node)
{
_mx35_clocks_init();
diff --git a/drivers/clk/samsung/clk-s3c2410-dclk.c b/drivers/clk/samsung/clk-s3c2410-dclk.c
index 7dad909..f5e0a6b 100644
--- a/drivers/clk/samsung/clk-s3c2410-dclk.c
+++ b/drivers/clk/samsung/clk-s3c2410-dclk.c
@@ -11,13 +11,10 @@
#include <linux/clk-provider.h>
#include <linux/io.h>
#include <linux/platform_device.h>
+#include <linux/platform_data/clk-s3c2410.h>
#include <linux/module.h>
#include "clk.h"
-/* legacy access to misccr, until dt conversion is finished */
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-
#define MUX_DCLK0 0
#define MUX_DCLK1 1
#define DIV_DCLK0 2
@@ -52,6 +49,7 @@ struct s3c24xx_clkout {
struct clk_hw hw;
u32 mask;
u8 shift;
+ unsigned int (*modify_misccr)(unsigned int clr, unsigned int chg);
};
#define to_s3c24xx_clkout(_hw) container_of(_hw, struct s3c24xx_clkout, hw)
@@ -62,7 +60,7 @@ static u8 s3c24xx_clkout_get_parent(struct clk_hw *hw)
int num_parents = clk_hw_get_num_parents(hw);
u32 val;
- val = readl_relaxed(S3C24XX_MISCCR) >> clkout->shift;
+ val = clkout->modify_misccr(0, 0) >> clkout->shift;
val >>= clkout->shift;
val &= clkout->mask;
@@ -76,7 +74,7 @@ static int s3c24xx_clkout_set_parent(struct clk_hw *hw, u8 index)
{
struct s3c24xx_clkout *clkout = to_s3c24xx_clkout(hw);
- s3c2410_modify_misccr((clkout->mask << clkout->shift),
+ clkout->modify_misccr((clkout->mask << clkout->shift),
(index << clkout->shift));
return 0;
@@ -92,10 +90,14 @@ static struct clk_hw *s3c24xx_register_clkout(struct device *dev,
const char *name, const char **parent_names, u8 num_parents,
u8 shift, u32 mask)
{
+ struct s3c2410_clk_platform_data *pdata = dev_get_platdata(dev);
struct s3c24xx_clkout *clkout;
struct clk_init_data init;
int ret;
+ if (!pdata)
+ return ERR_PTR(-EINVAL);
+
/* allocate the clkout */
clkout = kzalloc(sizeof(*clkout), GFP_KERNEL);
if (!clkout)
@@ -110,6 +112,7 @@ static struct clk_hw *s3c24xx_register_clkout(struct device *dev,
clkout->shift = shift;
clkout->mask = mask;
clkout->hw.init = &init;
+ clkout->modify_misccr = pdata->modify_misccr;
ret = clk_hw_register(dev, &clkout->hw);
if (ret)
diff --git a/drivers/clk/samsung/clk-s3c2410.c b/drivers/clk/samsung/clk-s3c2410.c
index fcf6764..5831d06 100644
--- a/drivers/clk/samsung/clk-s3c2410.c
+++ b/drivers/clk/samsung/clk-s3c2410.c
@@ -6,6 +6,7 @@
*/
#include <linux/clk-provider.h>
+#include <linux/clk/samsung.h>
#include <linux/of.h>
#include <linux/of_address.h>
diff --git a/drivers/clk/samsung/clk-s3c2412.c b/drivers/clk/samsung/clk-s3c2412.c
index a95ab5f..724ef64 100644
--- a/drivers/clk/samsung/clk-s3c2412.c
+++ b/drivers/clk/samsung/clk-s3c2412.c
@@ -6,6 +6,7 @@
*/
#include <linux/clk-provider.h>
+#include <linux/clk/samsung.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
diff --git a/drivers/clk/samsung/clk-s3c2443.c b/drivers/clk/samsung/clk-s3c2443.c
index c7aba1e..a827d63 100644
--- a/drivers/clk/samsung/clk-s3c2443.c
+++ b/drivers/clk/samsung/clk-s3c2443.c
@@ -6,6 +6,7 @@
*/
#include <linux/clk-provider.h>
+#include <linux/clk/samsung.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
diff --git a/drivers/clk/samsung/clk-s3c64xx.c b/drivers/clk/samsung/clk-s3c64xx.c
index b96d33e..56f95b6 100644
--- a/drivers/clk/samsung/clk-s3c64xx.c
+++ b/drivers/clk/samsung/clk-s3c64xx.c
@@ -7,6 +7,7 @@
#include <linux/slab.h>
#include <linux/clk-provider.h>
+#include <linux/clk/samsung.h>
#include <linux/of.h>
#include <linux/of_address.h>
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index bf5830e..015ec0c 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -196,7 +196,6 @@
config ARM_S3C2410_CPUFREQ
bool
depends on ARM_S3C24XX_CPUFREQ && CPU_S3C2410
- select S3C2410_CPUFREQ_UTILS
help
CPU Frequency scaling support for S3C2410
@@ -233,7 +232,6 @@
config ARM_S3C2440_CPUFREQ
bool "S3C2440/S3C2442 CPU Frequency scaling support"
depends on ARM_S3C24XX_CPUFREQ && (CPU_S3C2440 || CPU_S3C2442)
- select S3C2410_CPUFREQ_UTILS
default y
help
CPU Frequency scaling support for S3C2440 and S3C2442 SoC CPUs.
diff --git a/drivers/cpufreq/s3c2410-cpufreq.c b/drivers/cpufreq/s3c2410-cpufreq.c
index 0c4f2cc..5dcfbf0 100644
--- a/drivers/cpufreq/s3c2410-cpufreq.c
+++ b/drivers/cpufreq/s3c2410-cpufreq.c
@@ -16,14 +16,14 @@
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/regs-clock.h>
-
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#define S3C2410_CLKDIVN_PDIVN (1<<0)
+#define S3C2410_CLKDIVN_HDIVN (1<<1)
/* Note, 2410A has an extra mode for 1:4:4 ratio, bit 2 of CLKDIV */
@@ -37,7 +37,7 @@ static void s3c2410_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
if (cfg->divs.p_divisor != cfg->divs.h_divisor)
clkdiv |= S3C2410_CLKDIVN_PDIVN;
- __raw_writel(clkdiv, S3C2410_CLKDIVN);
+ s3c24xx_write_clkdivn(clkdiv);
}
static int s3c2410_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
diff --git a/drivers/cpufreq/s3c2412-cpufreq.c b/drivers/cpufreq/s3c2412-cpufreq.c
index 53385a9..5945945 100644
--- a/drivers/cpufreq/s3c2412-cpufreq.c
+++ b/drivers/cpufreq/s3c2412-cpufreq.c
@@ -19,15 +19,24 @@
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/regs-clock.h>
-#include <mach/s3c2412.h>
-
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#define S3C2412_CLKDIVN_PDIVN (1<<2)
+#define S3C2412_CLKDIVN_HDIVN_MASK (3<<0)
+#define S3C2412_CLKDIVN_ARMDIVN (1<<3)
+#define S3C2412_CLKDIVN_DVSEN (1<<4)
+#define S3C2412_CLKDIVN_HALFHCLK (1<<5)
+#define S3C2412_CLKDIVN_USB48DIV (1<<6)
+#define S3C2412_CLKDIVN_UARTDIV_MASK (15<<8)
+#define S3C2412_CLKDIVN_UARTDIV_SHIFT (8)
+#define S3C2412_CLKDIVN_I2SDIV_MASK (15<<12)
+#define S3C2412_CLKDIVN_I2SDIV_SHIFT (12)
+#define S3C2412_CLKDIVN_CAMDIV_MASK (15<<16)
+#define S3C2412_CLKDIVN_CAMDIV_SHIFT (16)
/* our clock resources. */
static struct clk *xtal;
@@ -117,7 +126,7 @@ static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
unsigned long clkdiv;
unsigned long olddiv;
- olddiv = clkdiv = __raw_readl(S3C2410_CLKDIVN);
+ olddiv = clkdiv = s3c24xx_read_clkdivn();
/* clear off current clock info */
@@ -134,32 +143,11 @@ static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
clkdiv |= S3C2412_CLKDIVN_PDIVN;
s3c_freq_dbg("%s: div %08lx => %08lx\n", __func__, olddiv, clkdiv);
- __raw_writel(clkdiv, S3C2410_CLKDIVN);
+ s3c24xx_write_clkdivn(clkdiv);
clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
}
-static void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg)
-{
- struct s3c_cpufreq_board *board = cfg->board;
- unsigned long refresh;
-
- s3c_freq_dbg("%s: refresh %u ns, hclk %lu\n", __func__,
- board->refresh, cfg->freq.hclk);
-
- /* Reduce both the refresh time (in ns) and the frequency (in MHz)
- * by 10 each to ensure that we do not overflow 32 bit numbers. This
- * should work for HCLK up to 133MHz and refresh period up to 30usec.
- */
-
- refresh = (board->refresh / 10);
- refresh *= (cfg->freq.hclk / 100);
- refresh /= (1 * 1000 * 1000); /* 10^6 */
-
- s3c_freq_dbg("%s: setting refresh 0x%08lx\n", __func__, refresh);
- __raw_writel(refresh, S3C2412_REFRESH);
-}
-
/* set the default cpu frequency information, based on an 200MHz part
* as we have no other way of detecting the speed rating in software.
*/
diff --git a/drivers/cpufreq/s3c2440-cpufreq.c b/drivers/cpufreq/s3c2440-cpufreq.c
index 3f772ba..148e8ae 100644
--- a/drivers/cpufreq/s3c2440-cpufreq.c
+++ b/drivers/cpufreq/s3c2440-cpufreq.c
@@ -20,14 +20,27 @@
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/regs-clock.h>
+#define S3C2440_CLKDIVN_PDIVN (1<<0)
+#define S3C2440_CLKDIVN_HDIVN_MASK (3<<1)
+#define S3C2440_CLKDIVN_HDIVN_1 (0<<1)
+#define S3C2440_CLKDIVN_HDIVN_2 (1<<1)
+#define S3C2440_CLKDIVN_HDIVN_4_8 (2<<1)
+#define S3C2440_CLKDIVN_HDIVN_3_6 (3<<1)
+#define S3C2440_CLKDIVN_UCLK (1<<3)
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#define S3C2440_CAMDIVN_CAMCLK_MASK (0xf<<0)
+#define S3C2440_CAMDIVN_CAMCLK_SEL (1<<4)
+#define S3C2440_CAMDIVN_HCLK3_HALF (1<<8)
+#define S3C2440_CAMDIVN_HCLK4_HALF (1<<9)
+#define S3C2440_CAMDIVN_DVSEN (1<<12)
+
+#define S3C2442_CAMDIVN_CAMCLK_DIV3 (1<<5)
static struct clk *xtal;
static struct clk *fclk;
@@ -143,8 +156,8 @@ static void s3c2440_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
s3c_freq_dbg("%s: divisors: h=%d, p=%d\n", __func__,
cfg->divs.h_divisor, cfg->divs.p_divisor);
- clkdiv = __raw_readl(S3C2410_CLKDIVN);
- camdiv = __raw_readl(S3C2440_CAMDIVN);
+ clkdiv = s3c24xx_read_clkdivn();
+ camdiv = s3c2440_read_camdivn();
clkdiv &= ~(S3C2440_CLKDIVN_HDIVN_MASK | S3C2440_CLKDIVN_PDIVN);
camdiv &= ~CAMDIVN_HCLK_HALF;
@@ -184,11 +197,11 @@ static void s3c2440_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
* then make a short delay and remove the hclk halving if necessary.
*/
- __raw_writel(camdiv | CAMDIVN_HCLK_HALF, S3C2440_CAMDIVN);
- __raw_writel(clkdiv, S3C2410_CLKDIVN);
+ s3c2440_write_camdivn(camdiv | CAMDIVN_HCLK_HALF);
+ s3c24xx_write_clkdivn(clkdiv);
ndelay(20);
- __raw_writel(camdiv, S3C2440_CAMDIVN);
+ s3c2440_write_camdivn(camdiv);
clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
}
diff --git a/drivers/cpufreq/s3c24xx-cpufreq-debugfs.c b/drivers/cpufreq/s3c24xx-cpufreq-debugfs.c
index 290e353..93971df 100644
--- a/drivers/cpufreq/s3c24xx-cpufreq-debugfs.c
+++ b/drivers/cpufreq/s3c24xx-cpufreq-debugfs.c
@@ -18,7 +18,7 @@
#include <linux/seq_file.h>
#include <linux/err.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
static struct dentry *dbgfs_root;
static struct dentry *dbgfs_file_io;
diff --git a/drivers/cpufreq/s3c24xx-cpufreq.c b/drivers/cpufreq/s3c24xx-cpufreq.c
index ed0e713..37efc0d 100644
--- a/drivers/cpufreq/s3c24xx-cpufreq.c
+++ b/drivers/cpufreq/s3c24xx-cpufreq.c
@@ -21,17 +21,13 @@
#include <linux/device.h>
#include <linux/sysfs.h>
#include <linux/slab.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
-
-#include <mach/regs-clock.h>
-
/* note, cpufreq support deals in kHz, no Hz */
-
static struct cpufreq_driver s3c24xx_driver;
static struct s3c_cpufreq_config cpu_cur;
static struct s3c_iotimings s3c24xx_iotiming;
@@ -68,7 +64,7 @@ static void s3c_cpufreq_getcur(struct s3c_cpufreq_config *cfg)
cfg->freq.pclk = pclk = clk_get_rate(clk_pclk);
cfg->freq.armclk = armclk = clk_get_rate(clk_arm);
- cfg->pll.driver_data = __raw_readl(S3C2410_MPLLCON);
+ cfg->pll.driver_data = s3c24xx_read_mpllcon();
cfg->pll.frequency = fclk;
cfg->freq.hclk_tns = 1000000000 / (cfg->freq.hclk / 10);
@@ -386,7 +382,7 @@ static unsigned int suspend_freq;
static int s3c_cpufreq_suspend(struct cpufreq_policy *policy)
{
suspend_pll.frequency = clk_get_rate(_clk_mpll);
- suspend_pll.driver_data = __raw_readl(S3C2410_MPLLCON);
+ suspend_pll.driver_data = s3c24xx_read_mpllcon();
suspend_freq = clk_get_rate(clk_arm);
return 0;
@@ -547,7 +543,7 @@ static void s3c_cpufreq_update_loctkime(void)
val |= calc_locktime(rate, cpu_cur.info->locktime_m);
pr_info("%s: new locktime is 0x%08x\n", __func__, val);
- __raw_writel(val, S3C2410_LOCKTIME);
+ s3c24xx_write_locktime(val);
}
static int s3c_cpufreq_build_freq(void)
diff --git a/drivers/hwmon/s3c-hwmon.c b/drivers/hwmon/s3c-hwmon.c
index b490fe3..f2703c5 100644
--- a/drivers/hwmon/s3c-hwmon.c
+++ b/drivers/hwmon/s3c-hwmon.c
@@ -20,7 +20,7 @@
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
-#include <plat/adc.h>
+#include <linux/soc/samsung/s3c-adc.h>
#include <linux/platform_data/hwmon-s3c.h>
struct s3c_hwmon_attr {
diff --git a/drivers/input/touchscreen/s3c2410_ts.c b/drivers/input/touchscreen/s3c2410_ts.c
index 82920ff..2e70c0b 100644
--- a/drivers/input/touchscreen/s3c2410_ts.c
+++ b/drivers/input/touchscreen/s3c2410_ts.c
@@ -20,10 +20,43 @@
#include <linux/clk.h>
#include <linux/io.h>
-#include <plat/adc.h>
-#include <plat/regs-adc.h>
+#include <linux/soc/samsung/s3c-adc.h>
#include <linux/platform_data/touchscreen-s3c2410.h>
+#define S3C2410_ADCCON (0x00)
+#define S3C2410_ADCTSC (0x04)
+#define S3C2410_ADCDLY (0x08)
+#define S3C2410_ADCDAT0 (0x0C)
+#define S3C2410_ADCDAT1 (0x10)
+#define S3C64XX_ADCUPDN (0x14)
+#define S3C2443_ADCMUX (0x18)
+#define S3C64XX_ADCCLRINT (0x18)
+#define S5P_ADCMUX (0x1C)
+#define S3C64XX_ADCCLRINTPNDNUP (0x20)
+
+/* ADCTSC Register Bits */
+#define S3C2443_ADCTSC_UD_SEN (1 << 8)
+#define S3C2410_ADCTSC_YM_SEN (1<<7)
+#define S3C2410_ADCTSC_YP_SEN (1<<6)
+#define S3C2410_ADCTSC_XM_SEN (1<<5)
+#define S3C2410_ADCTSC_XP_SEN (1<<4)
+#define S3C2410_ADCTSC_PULL_UP_DISABLE (1<<3)
+#define S3C2410_ADCTSC_AUTO_PST (1<<2)
+#define S3C2410_ADCTSC_XY_PST(x) (((x)&0x3)<<0)
+
+/* ADCDAT0 Bits */
+#define S3C2410_ADCDAT0_UPDOWN (1<<15)
+#define S3C2410_ADCDAT0_AUTO_PST (1<<14)
+#define S3C2410_ADCDAT0_XY_PST (0x3<<12)
+#define S3C2410_ADCDAT0_XPDATA_MASK (0x03FF)
+
+/* ADCDAT1 Bits */
+#define S3C2410_ADCDAT1_UPDOWN (1<<15)
+#define S3C2410_ADCDAT1_AUTO_PST (1<<14)
+#define S3C2410_ADCDAT1_XY_PST (0x3<<12)
+#define S3C2410_ADCDAT1_YPDATA_MASK (0x03FF)
+
+
#define TSC_SLEEP (S3C2410_ADCTSC_PULL_UP_DISABLE | S3C2410_ADCTSC_XY_PST(0))
#define INT_DOWN (0)
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index 80e3a84..94c2885 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -17,7 +17,6 @@
obj-$(CONFIG_ARCH_MMP) += irq-mmp.o
obj-$(CONFIG_IRQ_MXS) += irq-mxs.o
obj-$(CONFIG_ARCH_TEGRA) += irq-tegra.o
-obj-$(CONFIG_ARCH_S3C24XX) += irq-s3c24xx.o
obj-$(CONFIG_DW_APB_ICTL) += irq-dw-apb-ictl.o
obj-$(CONFIG_CLPS711X_IRQCHIP) += irq-clps711x.o
obj-$(CONFIG_OMPIC) += irq-ompic.o
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index f0cb7ae..31481c9 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -302,7 +302,7 @@
config MMC_SDHCI_S3C
tristate "SDHCI support on Samsung S3C SoC"
depends on MMC_SDHCI
- depends on PLAT_SAMSUNG || COMPILE_TEST
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
help
This selects the Secure Digital Host Controller Interface (SDHCI)
often referrered to as the HSMMC block in some of the Samsung S3C
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index e3698ab..643d54e 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -24,11 +24,6 @@
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/mmc/slot-gpio.h>
-
-#include <plat/gpio-cfg.h>
-#include <mach/dma.h>
-#include <mach/gpio-samsung.h>
-
#include <linux/platform_data/mmc-s3cmci.h>
#include "s3cmci.h"
@@ -305,7 +300,8 @@ static inline void clear_imask(struct s3cmci_host *host)
static void s3cmci_check_sdio_irq(struct s3cmci_host *host)
{
if (host->sdio_irqen) {
- if (gpio_get_value(S3C2410_GPE(8)) == 0) {
+ if (host->pdata->bus[3] &&
+ gpiod_get_value(host->pdata->bus[3]) == 0) {
pr_debug("%s: signalling irq\n", __func__);
mmc_signal_sdio_irq(host->mmc);
}
@@ -1201,33 +1197,20 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
switch (ios->power_mode) {
case MMC_POWER_ON:
case MMC_POWER_UP:
- /* Configure GPE5...GPE10 pins in SD mode */
- if (!host->pdev->dev.of_node)
- s3c_gpio_cfgall_range(S3C2410_GPE(5), 6, S3C_GPIO_SFN(2),
- S3C_GPIO_PULL_NONE);
-
- if (host->pdata->set_power)
- host->pdata->set_power(ios->power_mode, ios->vdd);
-
if (!host->is2440)
mci_con |= S3C2410_SDICON_FIFORESET;
-
break;
case MMC_POWER_OFF:
default:
- if (!host->pdev->dev.of_node)
- gpio_direction_output(S3C2410_GPE(5), 0);
-
if (host->is2440)
mci_con |= S3C2440_SDICON_SDRESET;
-
- if (host->pdata->set_power)
- host->pdata->set_power(ios->power_mode, ios->vdd);
-
break;
}
+ if (host->pdata->set_power)
+ host->pdata->set_power(ios->power_mode, ios->vdd);
+
s3cmci_set_clk(host, ios);
/* Set CLOCK_ENABLE */
@@ -1305,13 +1288,6 @@ static const struct mmc_host_ops s3cmci_ops = {
.enable_sdio_irq = s3cmci_enable_sdio_irq,
};
-static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
- /* This is currently here to avoid a number of if (host->pdata)
- * checks. Any zero fields to ensure reasonable defaults are picked. */
- .no_wprotect = 1,
- .no_detect = 1,
-};
-
#ifdef CONFIG_ARM_S3C24XX_CPUFREQ
static int s3cmci_cpufreq_transition(struct notifier_block *nb,
@@ -1465,23 +1441,20 @@ static int s3cmci_probe_pdata(struct s3cmci_host *host)
int i, ret;
host->is2440 = platform_get_device_id(pdev)->driver_data;
-
- for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++) {
- ret = gpio_request(i, dev_name(&pdev->dev));
- if (ret) {
- dev_err(&pdev->dev, "failed to get gpio %d\n", i);
-
- for (i--; i >= S3C2410_GPE(5); i--)
- gpio_free(i);
-
- return ret;
- }
+ pdata = pdev->dev.platform_data;
+ if (!pdata) {
+ dev_err(&pdev->dev, "need platform data");
+ return -ENXIO;
}
- if (!pdev->dev.platform_data)
- pdev->dev.platform_data = &s3cmci_def_pdata;
-
- pdata = pdev->dev.platform_data;
+ for (i = 0; i < 6; i++) {
+ pdata->bus[i] = devm_gpiod_get_index(&pdev->dev, "bus", i,
+ GPIOD_OUT_LOW);
+ if (IS_ERR(pdata->bus[i])) {
+ dev_err(&pdev->dev, "failed to get gpio %d\n", i);
+ return PTR_ERR(pdata->bus[i]);
+ }
+ }
if (pdata->no_wprotect)
mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT;
@@ -1537,7 +1510,6 @@ static int s3cmci_probe(struct platform_device *pdev)
struct s3cmci_host *host;
struct mmc_host *mmc;
int ret;
- int i;
mmc = mmc_alloc_host(sizeof(struct s3cmci_host), &pdev->dev);
if (!mmc) {
@@ -1581,7 +1553,7 @@ static int s3cmci_probe(struct platform_device *pdev)
"failed to get io memory region resource.\n");
ret = -ENOENT;
- goto probe_free_gpio;
+ goto probe_free_host;
}
host->mem = request_mem_region(host->mem->start,
@@ -1590,7 +1562,7 @@ static int s3cmci_probe(struct platform_device *pdev)
if (!host->mem) {
dev_err(&pdev->dev, "failed to request io memory region.\n");
ret = -ENOENT;
- goto probe_free_gpio;
+ goto probe_free_host;
}
host->base = ioremap(host->mem->start, resource_size(host->mem));
@@ -1714,11 +1686,6 @@ static int s3cmci_probe(struct platform_device *pdev)
probe_free_mem_region:
release_mem_region(host->mem->start, resource_size(host->mem));
- probe_free_gpio:
- if (!pdev->dev.of_node)
- for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
- gpio_free(i);
-
probe_free_host:
mmc_free_host(mmc);
@@ -1744,7 +1711,6 @@ static int s3cmci_remove(struct platform_device *pdev)
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
struct s3cmci_host *host = mmc_priv(mmc);
- int i;
s3cmci_shutdown(pdev);
@@ -1757,10 +1723,6 @@ static int s3cmci_remove(struct platform_device *pdev)
free_irq(host->irq, host);
- if (!pdev->dev.of_node)
- for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
- gpio_free(i);
-
iounmap(host->base);
release_mem_region(host->mem->start, resource_size(host->mem));
diff --git a/drivers/power/supply/s3c_adc_battery.c b/drivers/power/supply/s3c_adc_battery.c
index 3d00b35..60b7f41 100644
--- a/drivers/power/supply/s3c_adc_battery.c
+++ b/drivers/power/supply/s3c_adc_battery.c
@@ -22,7 +22,7 @@
#include <linux/init.h>
#include <linux/module.h>
-#include <plat/adc.h>
+#include <linux/soc/samsung/s3c-adc.h>
#define BAT_POLL_INTERVAL 10000 /* ms */
#define JITTER_DELAY 500 /* ms */
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 78ddc12..63be536 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -410,7 +410,7 @@
config PWM_SAMSUNG
tristate "Samsung PWM support"
- depends on PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
help
Generic PWM framework driver for Samsung.
diff --git a/drivers/soc/samsung/Kconfig b/drivers/soc/samsung/Kconfig
index 2641856..fc7f48a 100644
--- a/drivers/soc/samsung/Kconfig
+++ b/drivers/soc/samsung/Kconfig
@@ -35,7 +35,54 @@
config EXYNOS_PM_DOMAINS
bool "Exynos PM domains" if COMPILE_TEST
- depends on PM_GENERIC_DOMAINS || COMPILE_TEST
+ depends on (ARCH_EXYNOS && PM_GENERIC_DOMAINS) || COMPILE_TEST
+
+config SAMSUNG_PM_DEBUG
+ bool "Samsung PM Suspend debug"
+ depends on PM && DEBUG_KERNEL
+ depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
+ depends on DEBUG_S3C24XX_UART || DEBUG_S3C2410_UART
+ depends on DEBUG_LL && MMU
+ help
+ Say Y here if you want verbose debugging from the PM Suspend and
+ Resume code. See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
+ for more information.
+
+config S3C_PM_DEBUG_LED_SMDK
+ bool "SMDK LED suspend/resume debugging"
+ depends on PM && (MACH_SMDK6410)
+ help
+ Say Y here to enable the use of the SMDK LEDs on the baseboard
+ for debugging of the state of the suspend and resume process.
+
+ Note, this currently only works for S3C64XX based SMDK boards.
+
+config SAMSUNG_PM_CHECK
+ bool "S3C2410 PM Suspend Memory CRC"
+ depends on PM && (PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210)
+ select CRC32
+ help
+ Enable the PM code's memory area checksum over sleep. This option
+ will generate CRCs of all blocks of memory, and store them before
+ going to sleep. The blocks are then checked on resume for any
+ errors.
+
+ Note, this can take several seconds depending on memory size
+ and CPU speed.
+
+ See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
+
+config SAMSUNG_PM_CHECK_CHUNKSIZE
+ int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+ depends on PM && SAMSUNG_PM_CHECK
+ default 64
+ help
+ Set the chunksize in Kilobytes of the CRC for checking memory
+ corruption over suspend and resume. A smaller value will mean that
+ the CRC data block will take more memory, but will identify any
+ faults with better precision.
+
+ See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
config EXYNOS_REGULATOR_COUPLER
bool "Exynos SoC Regulator Coupler" if COMPILE_TEST
diff --git a/drivers/soc/samsung/Makefile b/drivers/soc/samsung/Makefile
index ecc3a32..59e8e94 100644
--- a/drivers/soc/samsung/Makefile
+++ b/drivers/soc/samsung/Makefile
@@ -10,3 +10,6 @@
exynos5250-pmu.o exynos5420-pmu.o
obj-$(CONFIG_EXYNOS_PM_DOMAINS) += pm_domains.o
obj-$(CONFIG_EXYNOS_REGULATOR_COUPLER) += exynos-regulator-coupler.o
+
+obj-$(CONFIG_SAMSUNG_PM_CHECK) += s3c-pm-check.o
+obj-$(CONFIG_SAMSUNG_PM_DEBUG) += s3c-pm-debug.o
diff --git a/arch/arm/plat-samsung/pm-check.c b/drivers/soc/samsung/s3c-pm-check.c
similarity index 98%
rename from arch/arm/plat-samsung/pm-check.c
rename to drivers/soc/samsung/s3c-pm-check.c
index cd2c02c6..ff3e099 100644
--- a/arch/arm/plat-samsung/pm-check.c
+++ b/drivers/soc/samsung/s3c-pm-check.c
@@ -15,7 +15,7 @@
#include <linux/ioport.h>
#include <linux/slab.h>
-#include <plat/pm-common.h>
+#include <linux/soc/samsung/s3c-pm.h>
#if CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE < 1
#error CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE must be a positive non-zero value
diff --git a/arch/arm/plat-samsung/pm-debug.c b/drivers/soc/samsung/s3c-pm-debug.c
similarity index 77%
rename from arch/arm/plat-samsung/pm-debug.c
rename to drivers/soc/samsung/s3c-pm-debug.c
index b76b1e9..b5ce0e9a4 100644
--- a/arch/arm/plat-samsung/pm-debug.c
+++ b/drivers/soc/samsung/s3c-pm-debug.c
@@ -15,17 +15,7 @@
#include <asm/mach/map.h>
-#include <plat/cpu.h>
-#include <plat/pm-common.h>
-
-#ifdef CONFIG_SAMSUNG_ATAGS
-#include <plat/pm.h>
-#include <mach/pm-core.h>
-#else
-static inline void s3c_pm_debug_init_uart(void) {}
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
- struct pm_uart_save *save) {}
-#endif
+#include <linux/soc/samsung/s3c-pm.h>
static struct pm_uart_save uart_save;
@@ -43,12 +33,6 @@ void s3c_pm_dbg(const char *fmt, ...)
printascii(buff);
}
-void s3c_pm_debug_init(void)
-{
- /* restart uart clocks so we can use them to output */
- s3c_pm_debug_init_uart();
-}
-
static inline void __iomem *s3c_pm_uart_base(void)
{
unsigned long paddr;
@@ -59,7 +43,7 @@ static inline void __iomem *s3c_pm_uart_base(void)
return (void __iomem *)vaddr;
}
-void s3c_pm_save_uarts(void)
+void s3c_pm_save_uarts(bool is_s3c2410)
{
void __iomem *regs = s3c_pm_uart_base();
struct pm_uart_save *save = &uart_save;
@@ -70,14 +54,14 @@ void s3c_pm_save_uarts(void)
save->umcon = __raw_readl(regs + S3C2410_UMCON);
save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
- if (!soc_is_s3c2410())
+ if (!is_s3c2410)
save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
}
-void s3c_pm_restore_uarts(void)
+void s3c_pm_restore_uarts(bool is_s3c2410)
{
void __iomem *regs = s3c_pm_uart_base();
struct pm_uart_save *save = &uart_save;
@@ -90,6 +74,6 @@ void s3c_pm_restore_uarts(void)
__raw_writel(save->umcon, regs + S3C2410_UMCON);
__raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
- if (!soc_is_s3c2410())
+ if (!is_s3c2410)
__raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
}
diff --git a/drivers/soc/ti/omap_prm.c b/drivers/soc/ti/omap_prm.c
index c9b3f9e..980b04c 100644
--- a/drivers/soc/ti/omap_prm.c
+++ b/drivers/soc/ti/omap_prm.c
@@ -10,14 +10,39 @@
#include <linux/device.h>
#include <linux/io.h>
#include <linux/iopoll.h>
+#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
#include <linux/reset-controller.h>
#include <linux/delay.h>
#include <linux/platform_data/ti-prm.h>
+enum omap_prm_domain_mode {
+ OMAP_PRMD_OFF,
+ OMAP_PRMD_RETENTION,
+ OMAP_PRMD_ON_INACTIVE,
+ OMAP_PRMD_ON_ACTIVE,
+};
+
+struct omap_prm_domain_map {
+ unsigned int usable_modes; /* Mask of hardware supported modes */
+ unsigned long statechange:1; /* Optional low-power state change */
+ unsigned long logicretstate:1; /* Optional logic off mode */
+};
+
+struct omap_prm_domain {
+ struct device *dev;
+ struct omap_prm *prm;
+ struct generic_pm_domain pd;
+ u16 pwrstctrl;
+ u16 pwrstst;
+ const struct omap_prm_domain_map *cap;
+ u32 pwrstctrl_saved;
+};
+
struct omap_rst_map {
s8 rst;
s8 st;
@@ -27,6 +52,9 @@ struct omap_prm_data {
u32 base;
const char *name;
const char *clkdm_name;
+ u16 pwrstctrl;
+ u16 pwrstst;
+ const struct omap_prm_domain_map *dmap;
u16 rstctrl;
u16 rstst;
const struct omap_rst_map *rstmap;
@@ -36,6 +64,7 @@ struct omap_prm_data {
struct omap_prm {
const struct omap_prm_data *data;
void __iomem *base;
+ struct omap_prm_domain *prmd;
};
struct omap_reset_data {
@@ -47,6 +76,7 @@ struct omap_reset_data {
struct device *dev;
};
+#define genpd_to_prm_domain(gpd) container_of(gpd, struct omap_prm_domain, pd)
#define to_omap_reset_data(p) container_of((p), struct omap_reset_data, rcdev)
#define OMAP_MAX_RESETS 8
@@ -58,6 +88,39 @@ struct omap_reset_data {
#define OMAP_PRM_HAS_RESETS (OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_RSTST)
+#define PRM_STATE_MAX_WAIT 10000
+#define PRM_LOGICRETSTATE BIT(2)
+#define PRM_LOWPOWERSTATECHANGE BIT(4)
+#define PRM_POWERSTATE_MASK OMAP_PRMD_ON_ACTIVE
+
+#define PRM_ST_INTRANSITION BIT(20)
+
+static const struct omap_prm_domain_map omap_prm_all = {
+ .usable_modes = BIT(OMAP_PRMD_ON_ACTIVE) | BIT(OMAP_PRMD_ON_INACTIVE) |
+ BIT(OMAP_PRMD_RETENTION) | BIT(OMAP_PRMD_OFF),
+ .statechange = 1,
+ .logicretstate = 1,
+};
+
+static const struct omap_prm_domain_map omap_prm_noinact = {
+ .usable_modes = BIT(OMAP_PRMD_ON_ACTIVE) | BIT(OMAP_PRMD_RETENTION) |
+ BIT(OMAP_PRMD_OFF),
+ .statechange = 1,
+ .logicretstate = 1,
+};
+
+static const struct omap_prm_domain_map omap_prm_nooff = {
+ .usable_modes = BIT(OMAP_PRMD_ON_ACTIVE) | BIT(OMAP_PRMD_ON_INACTIVE) |
+ BIT(OMAP_PRMD_RETENTION),
+ .statechange = 1,
+ .logicretstate = 1,
+};
+
+static const struct omap_prm_domain_map omap_prm_onoff_noauto = {
+ .usable_modes = BIT(OMAP_PRMD_ON_ACTIVE) | BIT(OMAP_PRMD_OFF),
+ .statechange = 1,
+};
+
static const struct omap_rst_map rst_map_0[] = {
{ .rst = 0, .st = 0 },
{ .rst = -1 },
@@ -78,6 +141,10 @@ static const struct omap_rst_map rst_map_012[] = {
static const struct omap_prm_data omap4_prm_data[] = {
{ .name = "tesla", .base = 0x4a306400, .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_01 },
+ {
+ .name = "abe", .base = 0x4a306500,
+ .pwrstctrl = 0, .pwrstst = 0x4, .dmap = &omap_prm_all,
+ },
{ .name = "core", .base = 0x4a306700, .rstctrl = 0x210, .rstst = 0x214, .clkdm_name = "ducati", .rstmap = rst_map_012 },
{ .name = "ivahd", .base = 0x4a306f00, .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_012 },
{ .name = "device", .base = 0x4a307b00, .rstctrl = 0x0, .rstst = 0x4, .rstmap = rst_map_01, .flags = OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_NO_CLKDM },
@@ -86,6 +153,10 @@ static const struct omap_prm_data omap4_prm_data[] = {
static const struct omap_prm_data omap5_prm_data[] = {
{ .name = "dsp", .base = 0x4ae06400, .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_01 },
+ {
+ .name = "abe", .base = 0x4ae06500,
+ .pwrstctrl = 0, .pwrstst = 0x4, .dmap = &omap_prm_nooff,
+ },
{ .name = "core", .base = 0x4ae06700, .rstctrl = 0x210, .rstst = 0x214, .clkdm_name = "ipu", .rstmap = rst_map_012 },
{ .name = "iva", .base = 0x4ae07200, .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_012 },
{ .name = "device", .base = 0x4ae07c00, .rstctrl = 0x0, .rstst = 0x4, .rstmap = rst_map_01, .flags = OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_NO_CLKDM },
@@ -119,7 +190,11 @@ static const struct omap_prm_data am3_prm_data[] = {
{ .name = "per", .base = 0x44e00c00, .rstctrl = 0x0, .rstmap = am3_per_rst_map, .flags = OMAP_PRM_HAS_RSTCTRL, .clkdm_name = "pruss_ocp" },
{ .name = "wkup", .base = 0x44e00d00, .rstctrl = 0x0, .rstst = 0xc, .rstmap = am3_wkup_rst_map, .flags = OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_NO_CLKDM },
{ .name = "device", .base = 0x44e00f00, .rstctrl = 0x0, .rstst = 0x8, .rstmap = rst_map_01, .flags = OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_NO_CLKDM },
- { .name = "gfx", .base = 0x44e01100, .rstctrl = 0x4, .rstst = 0x14, .rstmap = rst_map_0, .clkdm_name = "gfx_l3" },
+ {
+ .name = "gfx", .base = 0x44e01100,
+ .pwrstctrl = 0, .pwrstst = 0x10, .dmap = &omap_prm_noinact,
+ .rstctrl = 0x4, .rstst = 0x14, .rstmap = rst_map_0, .clkdm_name = "gfx_l3",
+ },
{ },
};
@@ -135,7 +210,11 @@ static const struct omap_rst_map am4_device_rst_map[] = {
};
static const struct omap_prm_data am4_prm_data[] = {
- { .name = "gfx", .base = 0x44df0400, .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_0, .clkdm_name = "gfx_l3" },
+ {
+ .name = "gfx", .base = 0x44df0400,
+ .pwrstctrl = 0, .pwrstst = 0x4, .dmap = &omap_prm_onoff_noauto,
+ .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_0, .clkdm_name = "gfx_l3",
+ },
{ .name = "per", .base = 0x44df0800, .rstctrl = 0x10, .rstst = 0x14, .rstmap = am4_per_rst_map, .clkdm_name = "pruss_ocp" },
{ .name = "wkup", .base = 0x44df2000, .rstctrl = 0x10, .rstst = 0x14, .rstmap = am3_wkup_rst_map, .flags = OMAP_PRM_HAS_NO_CLKDM },
{ .name = "device", .base = 0x44df4000, .rstctrl = 0x0, .rstst = 0x4, .rstmap = am4_device_rst_map, .flags = OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_NO_CLKDM },
@@ -151,6 +230,180 @@ static const struct of_device_id omap_prm_id_table[] = {
{ },
};
+#ifdef DEBUG
+static void omap_prm_domain_show_state(struct omap_prm_domain *prmd,
+ const char *desc)
+{
+ dev_dbg(prmd->dev, "%s %s: %08x/%08x\n",
+ prmd->pd.name, desc,
+ readl_relaxed(prmd->prm->base + prmd->pwrstctrl),
+ readl_relaxed(prmd->prm->base + prmd->pwrstst));
+}
+#else
+static inline void omap_prm_domain_show_state(struct omap_prm_domain *prmd,
+ const char *desc)
+{
+}
+#endif
+
+static int omap_prm_domain_power_on(struct generic_pm_domain *domain)
+{
+ struct omap_prm_domain *prmd;
+ int ret;
+ u32 v;
+
+ prmd = genpd_to_prm_domain(domain);
+ if (!prmd->cap)
+ return 0;
+
+ omap_prm_domain_show_state(prmd, "on: previous state");
+
+ if (prmd->pwrstctrl_saved)
+ v = prmd->pwrstctrl_saved;
+ else
+ v = readl_relaxed(prmd->prm->base + prmd->pwrstctrl);
+
+ writel_relaxed(v | OMAP_PRMD_ON_ACTIVE,
+ prmd->prm->base + prmd->pwrstctrl);
+
+ /* wait for the transition bit to get cleared */
+ ret = readl_relaxed_poll_timeout(prmd->prm->base + prmd->pwrstst,
+ v, !(v & PRM_ST_INTRANSITION), 1,
+ PRM_STATE_MAX_WAIT);
+ if (ret)
+ dev_err(prmd->dev, "%s: %s timed out\n",
+ prmd->pd.name, __func__);
+
+ omap_prm_domain_show_state(prmd, "on: new state");
+
+ return ret;
+}
+
+/* No need to check for holes in the mask for the lowest mode */
+static int omap_prm_domain_find_lowest(struct omap_prm_domain *prmd)
+{
+ return __ffs(prmd->cap->usable_modes);
+}
+
+static int omap_prm_domain_power_off(struct generic_pm_domain *domain)
+{
+ struct omap_prm_domain *prmd;
+ int ret;
+ u32 v;
+
+ prmd = genpd_to_prm_domain(domain);
+ if (!prmd->cap)
+ return 0;
+
+ omap_prm_domain_show_state(prmd, "off: previous state");
+
+ v = readl_relaxed(prmd->prm->base + prmd->pwrstctrl);
+ prmd->pwrstctrl_saved = v;
+
+ v &= ~PRM_POWERSTATE_MASK;
+ v |= omap_prm_domain_find_lowest(prmd);
+
+ if (prmd->cap->statechange)
+ v |= PRM_LOWPOWERSTATECHANGE;
+ if (prmd->cap->logicretstate)
+ v &= ~PRM_LOGICRETSTATE;
+ else
+ v |= PRM_LOGICRETSTATE;
+
+ writel_relaxed(v, prmd->prm->base + prmd->pwrstctrl);
+
+ /* wait for the transition bit to get cleared */
+ ret = readl_relaxed_poll_timeout(prmd->prm->base + prmd->pwrstst,
+ v, !(v & PRM_ST_INTRANSITION), 1,
+ PRM_STATE_MAX_WAIT);
+ if (ret)
+ dev_warn(prmd->dev, "%s: %s timed out\n",
+ __func__, prmd->pd.name);
+
+ omap_prm_domain_show_state(prmd, "off: new state");
+
+ return 0;
+}
+
+static int omap_prm_domain_attach_dev(struct generic_pm_domain *domain,
+ struct device *dev)
+{
+ struct generic_pm_domain_data *genpd_data;
+ struct of_phandle_args pd_args;
+ struct omap_prm_domain *prmd;
+ struct device_node *np;
+ int ret;
+
+ prmd = genpd_to_prm_domain(domain);
+ np = dev->of_node;
+
+ ret = of_parse_phandle_with_args(np, "power-domains",
+ "#power-domain-cells", 0, &pd_args);
+ if (ret < 0)
+ return ret;
+
+ if (pd_args.args_count != 0)
+ dev_warn(dev, "%s: unusupported #power-domain-cells: %i\n",
+ prmd->pd.name, pd_args.args_count);
+
+ genpd_data = dev_gpd_data(dev);
+ genpd_data->data = NULL;
+
+ return 0;
+}
+
+static void omap_prm_domain_detach_dev(struct generic_pm_domain *domain,
+ struct device *dev)
+{
+ struct generic_pm_domain_data *genpd_data;
+
+ genpd_data = dev_gpd_data(dev);
+ genpd_data->data = NULL;
+}
+
+static int omap_prm_domain_init(struct device *dev, struct omap_prm *prm)
+{
+ struct omap_prm_domain *prmd;
+ struct device_node *np = dev->of_node;
+ const struct omap_prm_data *data;
+ const char *name;
+ int error;
+
+ if (!of_find_property(dev->of_node, "#power-domain-cells", NULL))
+ return 0;
+
+ of_node_put(dev->of_node);
+
+ prmd = devm_kzalloc(dev, sizeof(*prmd), GFP_KERNEL);
+ if (!prmd)
+ return -ENOMEM;
+
+ data = prm->data;
+ name = devm_kasprintf(dev, GFP_KERNEL, "prm_%s",
+ data->name);
+
+ prmd->dev = dev;
+ prmd->prm = prm;
+ prmd->cap = prmd->prm->data->dmap;
+ prmd->pwrstctrl = prmd->prm->data->pwrstctrl;
+ prmd->pwrstst = prmd->prm->data->pwrstst;
+
+ prmd->pd.name = name;
+ prmd->pd.power_on = omap_prm_domain_power_on;
+ prmd->pd.power_off = omap_prm_domain_power_off;
+ prmd->pd.attach_dev = omap_prm_domain_attach_dev;
+ prmd->pd.detach_dev = omap_prm_domain_detach_dev;
+
+ pm_genpd_init(&prmd->pd, NULL, true);
+ error = of_genpd_add_provider_simple(np, &prmd->pd);
+ if (error)
+ pm_genpd_remove(&prmd->pd);
+ else
+ prm->prmd = prmd;
+
+ return error;
+}
+
static bool _is_valid_reset(struct omap_reset_data *reset, unsigned long id)
{
if (reset->mask & BIT(id))
@@ -351,6 +604,7 @@ static int omap_prm_probe(struct platform_device *pdev)
const struct omap_prm_data *data;
struct omap_prm *prm;
const struct of_device_id *match;
+ int ret;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
@@ -378,7 +632,21 @@ static int omap_prm_probe(struct platform_device *pdev)
if (IS_ERR(prm->base))
return PTR_ERR(prm->base);
- return omap_prm_reset_init(pdev, prm);
+ ret = omap_prm_domain_init(&pdev->dev, prm);
+ if (ret)
+ return ret;
+
+ ret = omap_prm_reset_init(pdev, prm);
+ if (ret)
+ goto err_domain;
+
+ return 0;
+
+err_domain:
+ of_genpd_del_provider(pdev->dev.of_node);
+ pm_genpd_remove(&prm->prmd->pd);
+
+ return ret;
}
static struct platform_driver omap_prm_driver = {
diff --git a/drivers/soc/ti/pm33xx.c b/drivers/soc/ti/pm33xx.c
index de0123e..d2f5e70 100644
--- a/drivers/soc/ti/pm33xx.c
+++ b/drivers/soc/ti/pm33xx.c
@@ -16,6 +16,7 @@
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/platform_data/pm33xx.h>
#include <linux/platform_device.h>
#include <linux/rtc.h>
@@ -39,6 +40,8 @@
#define GIC_INT_SET_PENDING_BASE 0x200
#define AM43XX_GIC_DIST_BASE 0x48241000
+static void __iomem *rtc_base_virt;
+static struct clk *rtc_fck;
static u32 rtc_magic_val;
static int (*am33xx_do_wfi_sram)(unsigned long unused);
@@ -90,7 +93,7 @@ static int am33xx_push_sram_idle(void)
ro_sram_data.amx3_pm_sram_data_virt = ocmcram_location_data;
ro_sram_data.amx3_pm_sram_data_phys =
gen_pool_virt_to_phys(sram_pool_data, ocmcram_location_data);
- ro_sram_data.rtc_base_virt = pm_ops->get_rtc_base_addr();
+ ro_sram_data.rtc_base_virt = rtc_base_virt;
/* Save physical address to calculate resume offset during pm init */
am33xx_do_wfi_sram_phys = gen_pool_virt_to_phys(sram_pool,
@@ -158,7 +161,7 @@ static struct wkup_m3_wakeup_src rtc_wake_src(void)
{
u32 i;
- i = __raw_readl(pm_ops->get_rtc_base_addr() + 0x44) & 0x40;
+ i = __raw_readl(rtc_base_virt + 0x44) & 0x40;
if (i) {
retrigger_irq = rtc_alarm_wakeup.irq_nr;
@@ -177,13 +180,24 @@ static int am33xx_rtc_only_idle(unsigned long wfi_flags)
return 0;
}
+/*
+ * Note that the RTC module clock must be re-enabled only for rtc+ddr suspend.
+ * And looks like the module can stay in SYSC_IDLE_SMART_WKUP mode configured
+ * by the interconnect code just fine for both rtc+ddr suspend and retention
+ * suspend.
+ */
static int am33xx_pm_suspend(suspend_state_t suspend_state)
{
int i, ret = 0;
if (suspend_state == PM_SUSPEND_MEM &&
pm_ops->check_off_mode_enable()) {
- pm_ops->prepare_rtc_suspend();
+ ret = clk_prepare_enable(rtc_fck);
+ if (ret) {
+ dev_err(pm33xx_dev, "Failed to enable clock: %i\n", ret);
+ return ret;
+ }
+
pm_ops->save_context();
suspend_wfi_flags |= WFI_FLAG_RTC_ONLY;
clk_save_context();
@@ -236,7 +250,7 @@ static int am33xx_pm_suspend(suspend_state_t suspend_state)
}
if (suspend_state == PM_SUSPEND_MEM && pm_ops->check_off_mode_enable())
- pm_ops->prepare_rtc_resume();
+ clk_disable_unprepare(rtc_fck);
return ret;
}
@@ -425,14 +439,28 @@ static int am33xx_pm_rtc_setup(void)
struct device_node *np;
unsigned long val = 0;
struct nvmem_device *nvmem;
+ int error;
np = of_find_node_by_name(NULL, "rtc");
if (of_device_is_available(np)) {
+ /* RTC interconnect target module clock */
+ rtc_fck = of_clk_get_by_name(np->parent, "fck");
+ if (IS_ERR(rtc_fck))
+ return PTR_ERR(rtc_fck);
+
+ rtc_base_virt = of_iomap(np, 0);
+ if (!rtc_base_virt) {
+ pr_warn("PM: could not iomap rtc");
+ error = -ENODEV;
+ goto err_clk_put;
+ }
+
omap_rtc = rtc_class_open("rtc0");
if (!omap_rtc) {
pr_warn("PM: rtc0 not available");
- return -EPROBE_DEFER;
+ error = -EPROBE_DEFER;
+ goto err_iounmap;
}
nvmem = devm_nvmem_device_get(&omap_rtc->dev,
@@ -454,6 +482,13 @@ static int am33xx_pm_rtc_setup(void)
}
return 0;
+
+err_iounmap:
+ iounmap(rtc_base_virt);
+err_clk_put:
+ clk_put(rtc_fck);
+
+ return error;
}
static int am33xx_pm_probe(struct platform_device *pdev)
@@ -544,6 +579,8 @@ static int am33xx_pm_remove(struct platform_device *pdev)
suspend_set_ops(NULL);
wkup_m3_ipc_put(m3_ipc);
am33xx_pm_free_sram();
+ iounmap(rtc_base_virt);
+ clk_put(rtc_fck);
return 0;
}
diff --git a/drivers/soc/versatile/soc-integrator.c b/drivers/soc/versatile/soc-integrator.c
index 7dcf77c..bab4ad8 100644
--- a/drivers/soc/versatile/soc-integrator.c
+++ b/drivers/soc/versatile/soc-integrator.c
@@ -100,7 +100,7 @@ ATTRIBUTE_GROUPS(integrator);
static int __init integrator_soc_init(void)
{
- static struct regmap *syscon_regmap;
+ struct regmap *syscon_regmap;
struct soc_device *soc_dev;
struct soc_device_attribute *soc_dev_attr;
struct device_node *np;
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index d2c976e..5cff60d 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -709,7 +709,7 @@
config SPI_S3C64XX
tristate "Samsung S3C64XX series type SPI"
- depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
+ depends on (PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST)
help
SPI driver for Samsung S3C64XX and newer SoCs.
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 21dc758..6fea582 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -98,7 +98,6 @@
obj-$(CONFIG_SPI_RSPI) += spi-rspi.o
obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o
spi-s3c24xx-hw-y := spi-s3c24xx.o
-spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o
obj-$(CONFIG_SPI_S3C64XX) += spi-s3c64xx.o
obj-$(CONFIG_SPI_SC18IS602) += spi-sc18is602.o
obj-$(CONFIG_SPI_SH) += spi-sh.o
diff --git a/arch/arm/plat-samsung/include/plat/regs-spi.h b/drivers/spi/spi-s3c24xx-regs.h
similarity index 88%
rename from arch/arm/plat-samsung/include/plat/regs-spi.h
rename to drivers/spi/spi-s3c24xx-regs.h
index 60784431..f51464ab 100644
--- a/arch/arm/plat-samsung/include/plat/regs-spi.h
+++ b/drivers/spi/spi-s3c24xx-regs.h
@@ -5,11 +5,8 @@
* S3C2410 SPI register definition
*/
-#ifndef __ASM_ARCH_REGS_SPI_H
-#define __ASM_ARCH_REGS_SPI_H
-
-#define S3C2410_SPI1 (0x20)
-#define S3C2412_SPI1 (0x100)
+#ifndef __SPI_S3C2410_H
+#define __SPI_S3C2410_H
#define S3C2410_SPCON (0x00)
@@ -41,4 +38,4 @@
#define S3C2410_SPTDAT (0x10)
#define S3C2410_SPRDAT (0x14)
-#endif /* __ASM_ARCH_REGS_SPI_H */
+#endif /* __SPI_S3C2410_H */
diff --git a/drivers/spi/spi-s3c24xx.c b/drivers/spi/spi-s3c24xx.c
index 7742170..d6f5169 100644
--- a/drivers/spi/spi-s3c24xx.c
+++ b/drivers/spi/spi-s3c24xx.c
@@ -19,13 +19,12 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/spi/s3c24xx.h>
+#include <linux/spi/s3c24xx-fiq.h>
#include <linux/module.h>
-#include <plat/regs-spi.h>
-
#include <asm/fiq.h>
-#include "spi-s3c24xx-fiq.h"
+#include "spi-s3c24xx-regs.h"
/**
* struct s3c24xx_spi_devstate - per device data
@@ -230,21 +229,6 @@ struct spi_fiq_code {
u8 data[];
};
-extern struct spi_fiq_code s3c24xx_spi_fiq_txrx;
-extern struct spi_fiq_code s3c24xx_spi_fiq_tx;
-extern struct spi_fiq_code s3c24xx_spi_fiq_rx;
-
-/**
- * ack_bit - turn IRQ into IRQ acknowledgement bit
- * @irq: The interrupt number
- *
- * Returns the bit to write to the interrupt acknowledge register.
- */
-static inline u32 ack_bit(unsigned int irq)
-{
- return 1 << (irq - IRQ_EINT0);
-}
-
/**
* s3c24xx_spi_tryfiq - attempt to claim and setup FIQ for transfer
* @hw: The hardware state.
@@ -261,6 +245,7 @@ static void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw)
struct pt_regs regs;
enum spi_fiq_mode mode;
struct spi_fiq_code *code;
+ u32 *ack_ptr = NULL;
int ret;
if (!hw->fiq_claimed) {
@@ -283,13 +268,10 @@ static void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw)
regs.uregs[fiq_rrx] = (long)hw->rx;
regs.uregs[fiq_rtx] = (long)hw->tx + 1;
regs.uregs[fiq_rcount] = hw->len - 1;
- regs.uregs[fiq_rirq] = (long)S3C24XX_VA_IRQ;
set_fiq_regs(®s);
if (hw->fiq_mode != mode) {
- u32 *ack_ptr;
-
hw->fiq_mode = mode;
switch (mode) {
@@ -309,12 +291,10 @@ static void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw)
BUG_ON(!code);
ack_ptr = (u32 *)&code->data[code->ack_offset];
- *ack_ptr = ack_bit(hw->irq);
-
set_fiq_handler(&code->data, code->length);
}
- s3c24xx_set_fiq(hw->irq, true);
+ s3c24xx_set_fiq(hw->irq, ack_ptr, true);
hw->fiq_mode = mode;
hw->fiq_inuse = 1;
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 20b98a3..1044fc3 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -236,7 +236,7 @@
config SERIAL_SAMSUNG
tristate "Samsung SoC serial support"
- depends on PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
select SERIAL_CORE
help
Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
diff --git a/drivers/usb/gadget/udc/s3c-hsudc.c b/drivers/usb/gadget/udc/s3c-hsudc.c
index aaca1b0..7bd5182 100644
--- a/drivers/usb/gadget/udc/s3c-hsudc.c
+++ b/drivers/usb/gadget/udc/s3c-hsudc.c
@@ -30,8 +30,6 @@
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
-#include <mach/regs-s3c2443-clock.h>
-
#define S3C_HSUDC_REG(x) (x)
/* Non-Indexed Registers */
@@ -186,53 +184,6 @@ static inline void __orr32(void __iomem *ptr, u32 val)
writel(readl(ptr) | val, ptr);
}
-static void s3c_hsudc_init_phy(void)
-{
- u32 cfg;
-
- cfg = readl(S3C2443_PWRCFG) | S3C2443_PWRCFG_USBPHY;
- writel(cfg, S3C2443_PWRCFG);
-
- cfg = readl(S3C2443_URSTCON);
- cfg |= (S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
- writel(cfg, S3C2443_URSTCON);
- mdelay(1);
-
- cfg = readl(S3C2443_URSTCON);
- cfg &= ~(S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
- writel(cfg, S3C2443_URSTCON);
-
- cfg = readl(S3C2443_PHYCTRL);
- cfg &= ~(S3C2443_PHYCTRL_CLKSEL | S3C2443_PHYCTRL_DSPORT);
- cfg |= (S3C2443_PHYCTRL_EXTCLK | S3C2443_PHYCTRL_PLLSEL);
- writel(cfg, S3C2443_PHYCTRL);
-
- cfg = readl(S3C2443_PHYPWR);
- cfg &= ~(S3C2443_PHYPWR_FSUSPEND | S3C2443_PHYPWR_PLL_PWRDN |
- S3C2443_PHYPWR_XO_ON | S3C2443_PHYPWR_PLL_REFCLK |
- S3C2443_PHYPWR_ANALOG_PD);
- cfg |= S3C2443_PHYPWR_COMMON_ON;
- writel(cfg, S3C2443_PHYPWR);
-
- cfg = readl(S3C2443_UCLKCON);
- cfg |= (S3C2443_UCLKCON_DETECT_VBUS | S3C2443_UCLKCON_FUNC_CLKEN |
- S3C2443_UCLKCON_TCLKEN);
- writel(cfg, S3C2443_UCLKCON);
-}
-
-static void s3c_hsudc_uninit_phy(void)
-{
- u32 cfg;
-
- cfg = readl(S3C2443_PWRCFG) & ~S3C2443_PWRCFG_USBPHY;
- writel(cfg, S3C2443_PWRCFG);
-
- writel(S3C2443_PHYPWR_FSUSPEND, S3C2443_PHYPWR);
-
- cfg = readl(S3C2443_UCLKCON) & ~S3C2443_UCLKCON_FUNC_CLKEN;
- writel(cfg, S3C2443_UCLKCON);
-}
-
/**
* s3c_hsudc_complete_request - Complete a transfer request.
* @hsep: Endpoint to which the request belongs.
@@ -1188,7 +1139,8 @@ static int s3c_hsudc_start(struct usb_gadget *gadget,
pm_runtime_get_sync(hsudc->dev);
- s3c_hsudc_init_phy();
+ if (hsudc->pd->phy_init)
+ hsudc->pd->phy_init();
if (hsudc->pd->gpio_init)
hsudc->pd->gpio_init();
@@ -1210,7 +1162,8 @@ static int s3c_hsudc_stop(struct usb_gadget *gadget)
spin_lock_irqsave(&hsudc->lock, flags);
hsudc->gadget.speed = USB_SPEED_UNKNOWN;
- s3c_hsudc_uninit_phy();
+ if (hsudc->pd->phy_uninit)
+ hsudc->pd->phy_uninit();
pm_runtime_put(hsudc->dev);
diff --git a/drivers/usb/gadget/udc/s3c2410_udc.c b/drivers/usb/gadget/udc/s3c2410_udc.c
index e875a0b..f1ea514 100644
--- a/drivers/usb/gadget/udc/s3c2410_udc.c
+++ b/drivers/usb/gadget/udc/s3c2410_udc.c
@@ -36,15 +36,11 @@
#include <asm/byteorder.h>
#include <asm/irq.h>
#include <asm/unaligned.h>
-#include <mach/irqs.h>
-#include <mach/hardware.h>
-
-#include <plat/regs-udc.h>
#include <linux/platform_data/usb-s3c2410_udc.h>
-
#include "s3c2410_udc.h"
+#include "s3c2410_udc_regs.h"
#define DRIVER_DESC "S3C2410 USB Device Controller Gadget"
#define DRIVER_AUTHOR "Herbert Pötzl <herbert@13thfloor.at>, " \
@@ -57,6 +53,7 @@ static struct s3c2410_udc *the_controller;
static struct clk *udc_clock;
static struct clk *usb_bus_clock;
static void __iomem *base_addr;
+static int irq_usbd;
static u64 rsrc_start;
static u64 rsrc_len;
static struct dentry *s3c2410_udc_debugfs_root;
@@ -835,8 +832,6 @@ static void s3c2410_udc_handle_ep(struct s3c2410_ep *ep)
}
}
-#include <mach/regs-irq.h>
-
/*
* s3c2410_udc_irq - interrupt handler
*/
@@ -977,7 +972,7 @@ static irqreturn_t s3c2410_udc_irq(int dummy, void *_dev)
}
}
- dprintk(DEBUG_VERBOSE, "irq: %d s3c2410_udc_done.\n", IRQ_USBD);
+ dprintk(DEBUG_VERBOSE, "irq: %d s3c2410_udc_done.\n", irq_usbd);
/* Restore old index */
udc_write(idx, S3C2410_UDC_INDEX_REG);
@@ -1777,13 +1772,7 @@ static int s3c2410_udc_probe(struct platform_device *pdev)
spin_lock_init(&udc->lock);
udc_info = dev_get_platdata(&pdev->dev);
- rsrc_start = S3C2410_PA_USBDEV;
- rsrc_len = S3C24XX_SZ_USBDEV;
-
- if (!request_mem_region(rsrc_start, rsrc_len, gadget_name))
- return -EBUSY;
-
- base_addr = ioremap(rsrc_start, rsrc_len);
+ base_addr = devm_platform_ioremap_resource(pdev, 0);
if (!base_addr) {
retval = -ENOMEM;
goto err_mem;
@@ -1795,17 +1784,19 @@ static int s3c2410_udc_probe(struct platform_device *pdev)
s3c2410_udc_disable(udc);
s3c2410_udc_reinit(udc);
+ irq_usbd = platform_get_irq(pdev, 0);
+
/* irq setup after old hardware state is cleaned up */
- retval = request_irq(IRQ_USBD, s3c2410_udc_irq,
+ retval = request_irq(irq_usbd, s3c2410_udc_irq,
0, gadget_name, udc);
if (retval != 0) {
- dev_err(dev, "cannot get irq %i, err %d\n", IRQ_USBD, retval);
+ dev_err(dev, "cannot get irq %i, err %d\n", irq_usbd, retval);
retval = -EBUSY;
goto err_map;
}
- dev_dbg(dev, "got irq %i\n", IRQ_USBD);
+ dev_dbg(dev, "got irq %i\n", irq_usbd);
if (udc_info && udc_info->vbus_pin > 0) {
retval = gpio_request(udc_info->vbus_pin, "udc vbus");
@@ -1872,7 +1863,7 @@ static int s3c2410_udc_probe(struct platform_device *pdev)
if (udc_info && udc_info->vbus_pin > 0)
gpio_free(udc_info->vbus_pin);
err_int:
- free_irq(IRQ_USBD, udc);
+ free_irq(irq_usbd, udc);
err_map:
iounmap(base_addr);
err_mem:
@@ -1906,7 +1897,7 @@ static int s3c2410_udc_remove(struct platform_device *pdev)
free_irq(irq, udc);
}
- free_irq(IRQ_USBD, udc);
+ free_irq(irq_usbd, udc);
iounmap(base_addr);
release_mem_region(rsrc_start, rsrc_len);
diff --git a/drivers/usb/gadget/udc/s3c2410_udc.h b/drivers/usb/gadget/udc/s3c2410_udc.h
index bdcaa8d..68bdf3e 100644
--- a/drivers/usb/gadget/udc/s3c2410_udc.h
+++ b/drivers/usb/gadget/udc/s3c2410_udc.h
@@ -90,6 +90,7 @@ struct s3c2410_udc {
unsigned req_pending : 1;
u8 vbus;
struct dentry *regs_info;
+ int irq;
};
#define to_s3c2410(g) (container_of((g), struct s3c2410_udc, gadget))
diff --git a/arch/arm/plat-samsung/include/plat/regs-udc.h b/drivers/usb/gadget/udc/s3c2410_udc_regs.h
similarity index 100%
rename from arch/arm/plat-samsung/include/plat/regs-udc.h
rename to drivers/usb/gadget/udc/s3c2410_udc_regs.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-lcd.h b/drivers/video/fbdev/s3c2410fb-regs-lcd.h
similarity index 83%
rename from arch/arm/mach-s3c24xx/include/mach/regs-lcd.h
rename to drivers/video/fbdev/s3c2410fb-regs-lcd.h
index 4c3434f..1e46f7a 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-lcd.h
+++ b/drivers/video/fbdev/s3c2410fb-regs-lcd.h
@@ -7,6 +7,13 @@
#ifndef ___ASM_ARCH_REGS_LCD_H
#define ___ASM_ARCH_REGS_LCD_H
+/*
+ * a couple of values are used as platform data in
+ * include/linux/platform_data/fb-s3c2410.h and not
+ * duplicated here.
+ */
+#include <linux/platform_data/fb-s3c2410.h>
+
#define S3C2410_LCDREG(x) (x)
/* LCD control registers */
@@ -29,13 +36,6 @@
#define S3C2410_LCDCON1_STN8BPP (3<<1)
#define S3C2410_LCDCON1_STN12BPP (4<<1)
-#define S3C2410_LCDCON1_TFT1BPP (8<<1)
-#define S3C2410_LCDCON1_TFT2BPP (9<<1)
-#define S3C2410_LCDCON1_TFT4BPP (10<<1)
-#define S3C2410_LCDCON1_TFT8BPP (11<<1)
-#define S3C2410_LCDCON1_TFT16BPP (12<<1)
-#define S3C2410_LCDCON1_TFT24BPP (13<<1)
-
#define S3C2410_LCDCON1_ENVID (1)
#define S3C2410_LCDCON1_MODEMASK 0x1E
@@ -66,20 +66,6 @@
#define S3C2410_LCDCON4_GET_HSPW(x) ( ((x) >> 0) & 0xFF)
-#define S3C2410_LCDCON5_BPP24BL (1<<12)
-#define S3C2410_LCDCON5_FRM565 (1<<11)
-#define S3C2410_LCDCON5_INVVCLK (1<<10)
-#define S3C2410_LCDCON5_INVVLINE (1<<9)
-#define S3C2410_LCDCON5_INVVFRAME (1<<8)
-#define S3C2410_LCDCON5_INVVD (1<<7)
-#define S3C2410_LCDCON5_INVVDEN (1<<6)
-#define S3C2410_LCDCON5_INVPWREN (1<<5)
-#define S3C2410_LCDCON5_INVLEND (1<<4)
-#define S3C2410_LCDCON5_PWREN (1<<3)
-#define S3C2410_LCDCON5_ENLEND (1<<2)
-#define S3C2410_LCDCON5_BSWP (1<<1)
-#define S3C2410_LCDCON5_HWSWP (1<<0)
-
/* framebuffer start addressed */
#define S3C2410_LCDSADDR1 S3C2410_LCDREG(0x14)
#define S3C2410_LCDSADDR2 S3C2410_LCDREG(0x18)
diff --git a/drivers/video/fbdev/s3c2410fb.c b/drivers/video/fbdev/s3c2410fb.c
index 6f8fa50..d8ae525 100644
--- a/drivers/video/fbdev/s3c2410fb.c
+++ b/drivers/video/fbdev/s3c2410fb.c
@@ -29,19 +29,18 @@
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/io.h>
+#include <linux/platform_data/fb-s3c2410.h>
#include <asm/div64.h>
#include <asm/mach/map.h>
-#include <mach/regs-lcd.h>
-#include <mach/regs-gpio.h>
-#include <mach/fb.h>
#ifdef CONFIG_PM
#include <linux/pm.h>
#endif
#include "s3c2410fb.h"
+#include "s3c2410fb-regs-lcd.h"
/* Debugging stuff */
static int debug = IS_BUILTIN(CONFIG_FB_S3C2410_DEBUG);
@@ -672,6 +671,9 @@ static inline void modify_gpio(void __iomem *reg,
{
unsigned long tmp;
+ if (!reg)
+ return;
+
tmp = readl(reg) & ~mask;
writel(tmp | set, reg);
}
@@ -702,10 +704,10 @@ static int s3c2410fb_init_registers(struct fb_info *info)
/* modify the gpio(s) with interrupts set (bjd) */
- modify_gpio(S3C2410_GPCUP, mach_info->gpcup, mach_info->gpcup_mask);
- modify_gpio(S3C2410_GPCCON, mach_info->gpccon, mach_info->gpccon_mask);
- modify_gpio(S3C2410_GPDUP, mach_info->gpdup, mach_info->gpdup_mask);
- modify_gpio(S3C2410_GPDCON, mach_info->gpdcon, mach_info->gpdcon_mask);
+ modify_gpio(mach_info->gpcup_reg, mach_info->gpcup, mach_info->gpcup_mask);
+ modify_gpio(mach_info->gpccon_reg, mach_info->gpccon, mach_info->gpccon_mask);
+ modify_gpio(mach_info->gpdup_reg, mach_info->gpdup, mach_info->gpdup_mask);
+ modify_gpio(mach_info->gpdcon_reg, mach_info->gpdcon, mach_info->gpdcon_mask);
local_irq_restore(flags);
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 21865e2..fd79686 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -489,16 +489,10 @@
Say N if you are unsure.
-config HAVE_S3C2410_WATCHDOG
- bool
- help
- This will include watchdog timer support for Samsung SoCs. If
- you want to include watchdog support for any machine, kindly
- select this in the respective mach-XXXX/Kconfig file.
-
config S3C2410_WATCHDOG
tristate "S3C2410 Watchdog"
- depends on HAVE_S3C2410_WATCHDOG || COMPILE_TEST
+ depends on ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210 || ARCH_EXYNOS || \
+ COMPILE_TEST
select WATCHDOG_CORE
select MFD_SYSCON if ARCH_EXYNOS
help
diff --git a/include/linux/clk/samsung.h b/include/linux/clk/samsung.h
new file mode 100644
index 0000000..79097e3
--- /dev/null
+++ b/include/linux/clk/samsung.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __LINUX_CLK_SAMSUNG_H_
+#define __LINUX_CLK_SAMSUNG_H_
+
+#include <linux/compiler_types.h>
+
+struct device_node;
+
+#ifdef CONFIG_ARCH_S3C64XX
+void s3c64xx_clk_init(struct device_node *np, unsigned long xtal_f,
+ unsigned long xusbxti_f, bool s3c6400,
+ void __iomem *base);
+#else
+static inline void s3c64xx_clk_init(struct device_node *np,
+ unsigned long xtal_f,
+ unsigned long xusbxti_f,
+ bool s3c6400, void __iomem *base) { }
+#endif /* CONFIG_ARCH_S3C64XX */
+
+#ifdef CONFIG_S3C2410_COMMON_CLK
+void s3c2410_common_clk_init(struct device_node *np, unsigned long xti_f,
+ int current_soc,
+ void __iomem *reg_base);
+#else
+static inline void s3c2410_common_clk_init(struct device_node *np,
+ unsigned long xti_f,
+ int current_soc,
+ void __iomem *reg_base) { }
+#endif /* CONFIG_S3C2410_COMMON_CLK */
+
+#ifdef CONFIG_S3C2412_COMMON_CLK
+void s3c2412_common_clk_init(struct device_node *np, unsigned long xti_f,
+ unsigned long ext_f, void __iomem *reg_base);
+#else
+static inline void s3c2412_common_clk_init(struct device_node *np,
+ unsigned long xti_f,
+ unsigned long ext_f,
+ void __iomem *reg_base) { }
+#endif /* CONFIG_S3C2412_COMMON_CLK */
+
+#ifdef CONFIG_S3C2443_COMMON_CLK
+void s3c2443_common_clk_init(struct device_node *np, unsigned long xti_f,
+ int current_soc,
+ void __iomem *reg_base);
+#else
+static inline void s3c2443_common_clk_init(struct device_node *np,
+ unsigned long xti_f,
+ int current_soc,
+ void __iomem *reg_base) { }
+#endif /* CONFIG_S3C2443_COMMON_CLK */
+
+#endif /* __LINUX_CLK_SAMSUNG_H_ */
diff --git a/include/linux/platform_data/clk-s3c2410.h b/include/linux/platform_data/clk-s3c2410.h
new file mode 100644
index 0000000..7eb1cfa
--- /dev/null
+++ b/include/linux/platform_data/clk-s3c2410.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_CLK_S3C2410_H_
+#define __LINUX_PLATFORM_DATA_CLK_S3C2410_H_
+
+/**
+ * struct s3c2410_clk_platform_data - platform data for S3C2410 clock driver
+ *
+ * @modify_misccr: Function to modify the MISCCR and return the new value
+ */
+struct s3c2410_clk_platform_data {
+ unsigned int (*modify_misccr)(unsigned int clr, unsigned int chg);
+};
+
+#endif /* __LINUX_PLATFORM_DATA_CLK_S3C2410_H_ */
+
diff --git a/include/linux/platform_data/fb-s3c2410.h b/include/linux/platform_data/fb-s3c2410.h
new file mode 100644
index 0000000..10c11e6
--- /dev/null
+++ b/include/linux/platform_data/fb-s3c2410.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2004 Arnaud Patard <arnaud.patard@rtp-net.org>
+ *
+ * Inspired by pxafb.h
+*/
+
+#ifndef __ASM_PLAT_FB_S3C2410_H
+#define __ASM_PLAT_FB_S3C2410_H __FILE__
+
+#include <linux/compiler_types.h>
+
+struct s3c2410fb_hw {
+ unsigned long lcdcon1;
+ unsigned long lcdcon2;
+ unsigned long lcdcon3;
+ unsigned long lcdcon4;
+ unsigned long lcdcon5;
+};
+
+/* LCD description */
+struct s3c2410fb_display {
+ /* LCD type */
+ unsigned type;
+#define S3C2410_LCDCON1_DSCAN4 (0<<5)
+#define S3C2410_LCDCON1_STN4 (1<<5)
+#define S3C2410_LCDCON1_STN8 (2<<5)
+#define S3C2410_LCDCON1_TFT (3<<5)
+
+#define S3C2410_LCDCON1_TFT1BPP (8<<1)
+#define S3C2410_LCDCON1_TFT2BPP (9<<1)
+#define S3C2410_LCDCON1_TFT4BPP (10<<1)
+#define S3C2410_LCDCON1_TFT8BPP (11<<1)
+#define S3C2410_LCDCON1_TFT16BPP (12<<1)
+#define S3C2410_LCDCON1_TFT24BPP (13<<1)
+
+ /* Screen size */
+ unsigned short width;
+ unsigned short height;
+
+ /* Screen info */
+ unsigned short xres;
+ unsigned short yres;
+ unsigned short bpp;
+
+ unsigned pixclock; /* pixclock in picoseconds */
+ unsigned short left_margin; /* value in pixels (TFT) or HCLKs (STN) */
+ unsigned short right_margin; /* value in pixels (TFT) or HCLKs (STN) */
+ unsigned short hsync_len; /* value in pixels (TFT) or HCLKs (STN) */
+ unsigned short upper_margin; /* value in lines (TFT) or 0 (STN) */
+ unsigned short lower_margin; /* value in lines (TFT) or 0 (STN) */
+ unsigned short vsync_len; /* value in lines (TFT) or 0 (STN) */
+
+ /* lcd configuration registers */
+ unsigned long lcdcon5;
+#define S3C2410_LCDCON5_BPP24BL (1<<12)
+#define S3C2410_LCDCON5_FRM565 (1<<11)
+#define S3C2410_LCDCON5_INVVCLK (1<<10)
+#define S3C2410_LCDCON5_INVVLINE (1<<9)
+#define S3C2410_LCDCON5_INVVFRAME (1<<8)
+#define S3C2410_LCDCON5_INVVD (1<<7)
+#define S3C2410_LCDCON5_INVVDEN (1<<6)
+#define S3C2410_LCDCON5_INVPWREN (1<<5)
+#define S3C2410_LCDCON5_INVLEND (1<<4)
+#define S3C2410_LCDCON5_PWREN (1<<3)
+#define S3C2410_LCDCON5_ENLEND (1<<2)
+#define S3C2410_LCDCON5_BSWP (1<<1)
+#define S3C2410_LCDCON5_HWSWP (1<<0)
+};
+
+struct s3c2410fb_mach_info {
+
+ struct s3c2410fb_display *displays; /* attached displays info */
+ unsigned num_displays; /* number of defined displays */
+ unsigned default_display;
+
+ /* GPIOs */
+
+ unsigned long gpcup;
+ unsigned long gpcup_mask;
+ unsigned long gpccon;
+ unsigned long gpccon_mask;
+ unsigned long gpdup;
+ unsigned long gpdup_mask;
+ unsigned long gpdcon;
+ unsigned long gpdcon_mask;
+
+ void __iomem * gpccon_reg;
+ void __iomem * gpcup_reg;
+ void __iomem * gpdcon_reg;
+ void __iomem * gpdup_reg;
+
+ /* lpc3600 control register */
+ unsigned long lpcsel;
+};
+
+extern void s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *);
+
+#endif /* __ASM_PLAT_FB_S3C2410_H */
diff --git a/include/linux/platform_data/mmc-s3cmci.h b/include/linux/platform_data/mmc-s3cmci.h
index 33310b1..bacb86d 100644
--- a/include/linux/platform_data/mmc-s3cmci.h
+++ b/include/linux/platform_data/mmc-s3cmci.h
@@ -35,6 +35,7 @@ struct s3c24xx_mci_pdata {
unsigned long ocr_avail;
void (*set_power)(unsigned char power_mode,
unsigned short vdd);
+ struct gpio_desc *bus[6];
};
/**
@@ -44,6 +45,7 @@ struct s3c24xx_mci_pdata {
* Copy the platform data supplied by @pdata so that this can be marked
* __initdata.
*/
+extern void s3c24xx_mci_def_set_power(unsigned char power_mode, unsigned short vdd);
extern void s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata);
#endif /* _ARCH_NCI_H */
diff --git a/include/linux/platform_data/pm33xx.h b/include/linux/platform_data/pm33xx.h
index 644af1d..7037ba7 100644
--- a/include/linux/platform_data/pm33xx.h
+++ b/include/linux/platform_data/pm33xx.h
@@ -54,11 +54,8 @@ struct am33xx_pm_platform_data {
void (*begin_suspend)(void);
void (*finish_suspend)(void);
struct am33xx_pm_sram_addr *(*get_sram_addrs)(void);
- void __iomem *(*get_rtc_base_addr)(void);
void (*save_context)(void);
void (*restore_context)(void);
- void (*prepare_rtc_suspend)(void);
- void (*prepare_rtc_resume)(void);
int (*check_off_mode_enable)(void);
};
diff --git a/include/linux/platform_data/s3c-hsudc.h b/include/linux/platform_data/s3c-hsudc.h
index 4dc9b87..a170939 100644
--- a/include/linux/platform_data/s3c-hsudc.h
+++ b/include/linux/platform_data/s3c-hsudc.h
@@ -26,6 +26,8 @@ struct s3c24xx_hsudc_platdata {
unsigned int epnum;
void (*gpio_init)(void);
void (*gpio_uninit)(void);
+ void (*phy_init)(void);
+ void (*phy_uninit)(void);
};
#endif /* __LINUX_USB_S3C_HSUDC_H */
diff --git a/arch/arm/plat-samsung/include/plat/adc.h b/include/linux/soc/samsung/s3c-adc.h
similarity index 85%
rename from arch/arm/plat-samsung/include/plat/adc.h
rename to include/linux/soc/samsung/s3c-adc.h
index 74d1a46..591c94e 100644
--- a/arch/arm/plat-samsung/include/plat/adc.h
+++ b/include/linux/soc/samsung/s3c-adc.h
@@ -7,8 +7,8 @@
* S3C ADC driver information
*/
-#ifndef __ASM_PLAT_ADC_H
-#define __ASM_PLAT_ADC_H __FILE__
+#ifndef __LINUX_SOC_SAMSUNG_S3C_ADC_H
+#define __LINUX_SOC_SAMSUNG_S3C_ADC_H __FILE__
struct s3c_adc_client;
struct platform_device;
@@ -29,4 +29,4 @@ extern struct s3c_adc_client *
extern void s3c_adc_release(struct s3c_adc_client *client);
-#endif /* __ASM_PLAT_ADC_H */
+#endif /* __LINUX_SOC_SAMSUNG_S3C_ADC_H */
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq.h b/include/linux/soc/samsung/s3c-cpu-freq.h
similarity index 97%
rename from arch/arm/plat-samsung/include/plat/cpu-freq.h
rename to include/linux/soc/samsung/s3c-cpu-freq.h
index 558892b..63e88fd 100644
--- a/arch/arm/plat-samsung/include/plat/cpu-freq.h
+++ b/include/linux/soc/samsung/s3c-cpu-freq.h
@@ -6,6 +6,8 @@
*
* S3C CPU frequency scaling support - driver and board
*/
+#ifndef __LINUX_SOC_SAMSUNG_S3C_CPU_FREQ_H
+#define __LINUX_SOC_SAMSUNG_S3C_CPU_FREQ_H
#include <linux/cpufreq.h>
@@ -139,3 +141,5 @@ static inline int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board)
return 0;
}
#endif /* CONFIG_ARM_S3C_CPUFREQ */
+
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/include/linux/soc/samsung/s3c-cpufreq-core.h
similarity index 94%
rename from arch/arm/plat-samsung/include/plat/cpu-freq-core.h
rename to include/linux/soc/samsung/s3c-cpufreq-core.h
index 2c7cf26..3b278af 100644
--- a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
+++ b/include/linux/soc/samsung/s3c-cpufreq-core.h
@@ -6,8 +6,10 @@
*
* S3C CPU frequency scaling support - core support
*/
+#ifndef __LINUX_SOC_SAMSUNG_S3C_CPUFREQ_CORE_H
+#define __LINUX_SOC_SAMSUNG_S3C_CPUFREQ_CORE_H
-#include <plat/cpu-freq.h>
+#include <linux/soc/samsung/s3c-cpu-freq.h>
struct seq_file;
@@ -246,6 +248,7 @@ extern int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg,
extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg,
struct s3c_iotimings *iot);
+extern void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg);
#else
#define s3c2412_iotiming_debugfs NULL
#define s3c2412_iotiming_calc NULL
@@ -285,3 +288,12 @@ static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table,
return index + 1;
}
+
+u32 s3c2440_read_camdivn(void);
+void s3c2440_write_camdivn(u32 camdiv);
+u32 s3c24xx_read_clkdivn(void);
+void s3c24xx_write_clkdivn(u32 clkdiv);
+u32 s3c24xx_read_mpllcon(void);
+void s3c24xx_write_locktime(u32 locktime);
+
+#endif
diff --git a/include/linux/soc/samsung/s3c-pm.h b/include/linux/soc/samsung/s3c-pm.h
new file mode 100644
index 0000000..f916455
--- /dev/null
+++ b/include/linux/soc/samsung/s3c-pm.h
@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Tomasz Figa <t.figa@samsung.com>
+ * Copyright (c) 2004 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Written by Ben Dooks, <ben@simtec.co.uk>
+ */
+
+#ifndef __LINUX_SOC_SAMSUNG_S3C_PM_H
+#define __LINUX_SOC_SAMSUNG_S3C_PM_H __FILE__
+
+#include <linux/types.h>
+
+/* PM debug functions */
+
+/**
+ * struct pm_uart_save - save block for core UART
+ * @ulcon: Save value for S3C2410_ULCON
+ * @ucon: Save value for S3C2410_UCON
+ * @ufcon: Save value for S3C2410_UFCON
+ * @umcon: Save value for S3C2410_UMCON
+ * @ubrdiv: Save value for S3C2410_UBRDIV
+ *
+ * Save block for UART registers to be held over sleep and restored if they
+ * are needed (say by debug).
+*/
+struct pm_uart_save {
+ u32 ulcon;
+ u32 ucon;
+ u32 ufcon;
+ u32 umcon;
+ u32 ubrdiv;
+ u32 udivslot;
+};
+
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+/**
+ * s3c_pm_dbg() - low level debug function for use in suspend/resume.
+ * @msg: The message to print.
+ *
+ * This function is used mainly to debug the resume process before the system
+ * can rely on printk/console output. It uses the low-level debugging output
+ * routine printascii() to do its work.
+ */
+extern void s3c_pm_dbg(const char *msg, ...);
+
+#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
+
+extern void s3c_pm_save_uarts(bool is_s3c24xx);
+extern void s3c_pm_restore_uarts(bool is_s3c24xx);
+
+#ifdef CONFIG_ARCH_S3C64XX
+extern void s3c_pm_arch_update_uart(void __iomem *regs,
+ struct pm_uart_save *save);
+#else
+static inline void
+s3c_pm_arch_update_uart(void __iomem *regs, struct pm_uart_save *save)
+{
+}
+#endif
+
+#else
+#define S3C_PMDBG(fmt...) pr_debug(fmt)
+
+static inline void s3c_pm_save_uarts(bool is_s3c24xx) { }
+static inline void s3c_pm_restore_uarts(bool is_s3c24xx) { }
+#endif
+
+/* suspend memory checking */
+
+#ifdef CONFIG_SAMSUNG_PM_CHECK
+extern void s3c_pm_check_prepare(void);
+extern void s3c_pm_check_restore(void);
+extern void s3c_pm_check_cleanup(void);
+extern void s3c_pm_check_store(void);
+#else
+#define s3c_pm_check_prepare() do { } while (0)
+#define s3c_pm_check_restore() do { } while (0)
+#define s3c_pm_check_cleanup() do { } while (0)
+#define s3c_pm_check_store() do { } while (0)
+#endif
+
+/* system device subsystems */
+
+extern struct bus_type s3c2410_subsys;
+extern struct bus_type s3c2410a_subsys;
+extern struct bus_type s3c2412_subsys;
+extern struct bus_type s3c2416_subsys;
+extern struct bus_type s3c2440_subsys;
+extern struct bus_type s3c2442_subsys;
+extern struct bus_type s3c2443_subsys;
+
+#endif
diff --git a/drivers/spi/spi-s3c24xx-fiq.h b/include/linux/spi/s3c24xx-fiq.h
similarity index 66%
rename from drivers/spi/spi-s3c24xx-fiq.h
rename to include/linux/spi/s3c24xx-fiq.h
index 7786b0e..d2842ac 100644
--- a/drivers/spi/spi-s3c24xx-fiq.h
+++ b/include/linux/spi/s3c24xx-fiq.h
@@ -7,11 +7,19 @@
* S3C24XX SPI - FIQ pseudo-DMA transfer support
*/
+#ifndef __LINUX_SPI_S3C24XX_FIQ_H
+#define __LINUX_SPI_S3C24XX_FIQ_H __FILE__
+
/* We have R8 through R13 to play with */
#ifdef __ASSEMBLY__
#define __REG_NR(x) r##x
#else
+
+extern struct spi_fiq_code s3c24xx_spi_fiq_txrx;
+extern struct spi_fiq_code s3c24xx_spi_fiq_tx;
+extern struct spi_fiq_code s3c24xx_spi_fiq_rx;
+
#define __REG_NR(x) (x)
#endif
@@ -21,3 +29,5 @@
#define fiq_rtx __REG_NR(11)
#define fiq_rcount __REG_NR(12)
#define fiq_rirq __REG_NR(13)
+
+#endif /* __LINUX_SPI_S3C24XX_FIQ_H */
diff --git a/include/linux/spi/s3c24xx.h b/include/linux/spi/s3c24xx.h
index c91d10b..440a715 100644
--- a/include/linux/spi/s3c24xx.h
+++ b/include/linux/spi/s3c24xx.h
@@ -20,6 +20,6 @@ struct s3c2410_spi_info {
void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol);
};
-extern int s3c24xx_set_fiq(unsigned int irq, bool on);
+extern int s3c24xx_set_fiq(unsigned int irq, u32 *ack_ptr, bool on);
#endif /* __LINUX_SPI_S3C24XX_H */
diff --git a/include/media/drv-intf/s3c_camif.h b/include/media/drv-intf/s3c_camif.h
index d1200b4..f746851 100644
--- a/include/media/drv-intf/s3c_camif.h
+++ b/include/media/drv-intf/s3c_camif.h
@@ -35,8 +35,4 @@ struct s3c_camif_plat_data {
int (*gpio_put)(void);
};
-/* Platform default helper functions */
-int s3c_camif_gpio_get(void);
-int s3c_camif_gpio_put(void);
-
#endif /* MEDIA_S3C_CAMIF_ */
diff --git a/sound/soc/samsung/Kconfig b/sound/soc/samsung/Kconfig
index 1431be4..a2221eb 100644
--- a/sound/soc/samsung/Kconfig
+++ b/sound/soc/samsung/Kconfig
@@ -1,7 +1,7 @@
# SPDX-License-Identifier: GPL-2.0-only
menuconfig SND_SOC_SAMSUNG
tristate "ASoC support for Samsung"
- depends on PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST
+ depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
depends on COMMON_CLK
select SND_SOC_GENERIC_DMAENGINE_PCM
help
diff --git a/sound/soc/samsung/s3c2412-i2s.c b/sound/soc/samsung/s3c2412-i2s.c
index edfa9d1..81f416a 100644
--- a/sound/soc/samsung/s3c2412-i2s.c
+++ b/sound/soc/samsung/s3c2412-i2s.c
@@ -19,9 +19,6 @@
#include <sound/soc.h>
#include <sound/pcm_params.h>
-#include <mach/gpio-samsung.h>
-#include <plat/gpio-cfg.h>
-
#include "dma.h"
#include "regs-i2s-v2.h"
#include "s3c2412-i2s.h"
@@ -70,10 +67,6 @@ static int s3c2412_i2s_probe(struct snd_soc_dai *dai)
if (ret)
goto err;
- /* Configure the I2S pins (GPE0...GPE4) in correct mode */
- s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
- S3C_GPIO_PULL_NONE);
-
return 0;
err:
diff --git a/sound/soc/samsung/s3c24xx-i2s.c b/sound/soc/samsung/s3c24xx-i2s.c
index 60bfaed..50c0800 100644
--- a/sound/soc/samsung/s3c24xx-i2s.c
+++ b/sound/soc/samsung/s3c24xx-i2s.c
@@ -18,10 +18,7 @@
#include <sound/soc.h>
#include <sound/pcm_params.h>
-#include <mach/gpio-samsung.h>
-#include <plat/gpio-cfg.h>
#include "regs-iis.h"
-
#include "dma.h"
#include "s3c24xx-i2s.h"
@@ -348,10 +345,6 @@ static int s3c24xx_i2s_probe(struct snd_soc_dai *dai)
if (ret)
return ret;
- /* Configure the I2S pins (GPE0...GPE4) in correct mode */
- s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
- S3C_GPIO_PULL_NONE);
-
writel(S3C2410_IISCON_IISEN, s3c24xx_i2s.regs + S3C2410_IISCON);
s3c24xx_snd_txctrl(0);
