| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Lantiq / Intel GSWIP switch driver for VRX200 SoCs |
| * |
| * Copyright (C) 2010 Lantiq Deutschland |
| * Copyright (C) 2012 John Crispin <john@phrozen.org> |
| * Copyright (C) 2017 - 2019 Hauke Mehrtens <hauke@hauke-m.de> |
| * |
| * The VLAN and bridge model the GSWIP hardware uses does not directly |
| * matches the model DSA uses. |
| * |
| * The hardware has 64 possible table entries for bridges with one VLAN |
| * ID, one flow id and a list of ports for each bridge. All entries which |
| * match the same flow ID are combined in the mac learning table, they |
| * act as one global bridge. |
| * The hardware does not support VLAN filter on the port, but on the |
| * bridge, this driver converts the DSA model to the hardware. |
| * |
| * The CPU gets all the exception frames which do not match any forwarding |
| * rule and the CPU port is also added to all bridges. This makes it possible |
| * to handle all the special cases easily in software. |
| * At the initialization the driver allocates one bridge table entry for |
| * each switch port which is used when the port is used without an |
| * explicit bridge. This prevents the frames from being forwarded |
| * between all LAN ports by default. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/etherdevice.h> |
| #include <linux/firmware.h> |
| #include <linux/if_bridge.h> |
| #include <linux/if_vlan.h> |
| #include <linux/iopoll.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of_mdio.h> |
| #include <linux/of_net.h> |
| #include <linux/of_platform.h> |
| #include <linux/phy.h> |
| #include <linux/phylink.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| #include <net/dsa.h> |
| #include <dt-bindings/mips/lantiq_rcu_gphy.h> |
| |
| #include "lantiq_pce.h" |
| |
| /* GSWIP MDIO Registers */ |
| #define GSWIP_MDIO_GLOB 0x00 |
| #define GSWIP_MDIO_GLOB_ENABLE BIT(15) |
| #define GSWIP_MDIO_CTRL 0x08 |
| #define GSWIP_MDIO_CTRL_BUSY BIT(12) |
| #define GSWIP_MDIO_CTRL_RD BIT(11) |
| #define GSWIP_MDIO_CTRL_WR BIT(10) |
| #define GSWIP_MDIO_CTRL_PHYAD_MASK 0x1f |
| #define GSWIP_MDIO_CTRL_PHYAD_SHIFT 5 |
| #define GSWIP_MDIO_CTRL_REGAD_MASK 0x1f |
| #define GSWIP_MDIO_READ 0x09 |
| #define GSWIP_MDIO_WRITE 0x0A |
| #define GSWIP_MDIO_MDC_CFG0 0x0B |
| #define GSWIP_MDIO_MDC_CFG1 0x0C |
| #define GSWIP_MDIO_PHYp(p) (0x15 - (p)) |
| #define GSWIP_MDIO_PHY_LINK_MASK 0x6000 |
| #define GSWIP_MDIO_PHY_LINK_AUTO 0x0000 |
| #define GSWIP_MDIO_PHY_LINK_DOWN 0x4000 |
| #define GSWIP_MDIO_PHY_LINK_UP 0x2000 |
| #define GSWIP_MDIO_PHY_SPEED_MASK 0x1800 |
| #define GSWIP_MDIO_PHY_SPEED_AUTO 0x1800 |
| #define GSWIP_MDIO_PHY_SPEED_M10 0x0000 |
| #define GSWIP_MDIO_PHY_SPEED_M100 0x0800 |
| #define GSWIP_MDIO_PHY_SPEED_G1 0x1000 |
| #define GSWIP_MDIO_PHY_FDUP_MASK 0x0600 |
| #define GSWIP_MDIO_PHY_FDUP_AUTO 0x0000 |
| #define GSWIP_MDIO_PHY_FDUP_EN 0x0200 |
| #define GSWIP_MDIO_PHY_FDUP_DIS 0x0600 |
| #define GSWIP_MDIO_PHY_FCONTX_MASK 0x0180 |
| #define GSWIP_MDIO_PHY_FCONTX_AUTO 0x0000 |
| #define GSWIP_MDIO_PHY_FCONTX_EN 0x0100 |
| #define GSWIP_MDIO_PHY_FCONTX_DIS 0x0180 |
| #define GSWIP_MDIO_PHY_FCONRX_MASK 0x0060 |
| #define GSWIP_MDIO_PHY_FCONRX_AUTO 0x0000 |
| #define GSWIP_MDIO_PHY_FCONRX_EN 0x0020 |
| #define GSWIP_MDIO_PHY_FCONRX_DIS 0x0060 |
| #define GSWIP_MDIO_PHY_ADDR_MASK 0x001f |
| #define GSWIP_MDIO_PHY_MASK (GSWIP_MDIO_PHY_ADDR_MASK | \ |
| GSWIP_MDIO_PHY_FCONRX_MASK | \ |
| GSWIP_MDIO_PHY_FCONTX_MASK | \ |
| GSWIP_MDIO_PHY_LINK_MASK | \ |
| GSWIP_MDIO_PHY_SPEED_MASK | \ |
| GSWIP_MDIO_PHY_FDUP_MASK) |
| |
| /* GSWIP MII Registers */ |
| #define GSWIP_MII_CFGp(p) (0x2 * (p)) |
| #define GSWIP_MII_CFG_RESET BIT(15) |
| #define GSWIP_MII_CFG_EN BIT(14) |
| #define GSWIP_MII_CFG_ISOLATE BIT(13) |
| #define GSWIP_MII_CFG_LDCLKDIS BIT(12) |
| #define GSWIP_MII_CFG_RGMII_IBS BIT(8) |
| #define GSWIP_MII_CFG_RMII_CLK BIT(7) |
| #define GSWIP_MII_CFG_MODE_MIIP 0x0 |
| #define GSWIP_MII_CFG_MODE_MIIM 0x1 |
| #define GSWIP_MII_CFG_MODE_RMIIP 0x2 |
| #define GSWIP_MII_CFG_MODE_RMIIM 0x3 |
| #define GSWIP_MII_CFG_MODE_RGMII 0x4 |
| #define GSWIP_MII_CFG_MODE_MASK 0xf |
| #define GSWIP_MII_CFG_RATE_M2P5 0x00 |
| #define GSWIP_MII_CFG_RATE_M25 0x10 |
| #define GSWIP_MII_CFG_RATE_M125 0x20 |
| #define GSWIP_MII_CFG_RATE_M50 0x30 |
| #define GSWIP_MII_CFG_RATE_AUTO 0x40 |
| #define GSWIP_MII_CFG_RATE_MASK 0x70 |
| #define GSWIP_MII_PCDU0 0x01 |
| #define GSWIP_MII_PCDU1 0x03 |
| #define GSWIP_MII_PCDU5 0x05 |
| #define GSWIP_MII_PCDU_TXDLY_MASK GENMASK(2, 0) |
| #define GSWIP_MII_PCDU_RXDLY_MASK GENMASK(9, 7) |
| |
| /* GSWIP Core Registers */ |
| #define GSWIP_SWRES 0x000 |
| #define GSWIP_SWRES_R1 BIT(1) /* GSWIP Software reset */ |
| #define GSWIP_SWRES_R0 BIT(0) /* GSWIP Hardware reset */ |
| #define GSWIP_VERSION 0x013 |
| #define GSWIP_VERSION_REV_SHIFT 0 |
| #define GSWIP_VERSION_REV_MASK GENMASK(7, 0) |
| #define GSWIP_VERSION_MOD_SHIFT 8 |
| #define GSWIP_VERSION_MOD_MASK GENMASK(15, 8) |
| #define GSWIP_VERSION_2_0 0x100 |
| #define GSWIP_VERSION_2_1 0x021 |
| #define GSWIP_VERSION_2_2 0x122 |
| #define GSWIP_VERSION_2_2_ETC 0x022 |
| |
| #define GSWIP_BM_RAM_VAL(x) (0x043 - (x)) |
| #define GSWIP_BM_RAM_ADDR 0x044 |
| #define GSWIP_BM_RAM_CTRL 0x045 |
| #define GSWIP_BM_RAM_CTRL_BAS BIT(15) |
| #define GSWIP_BM_RAM_CTRL_OPMOD BIT(5) |
| #define GSWIP_BM_RAM_CTRL_ADDR_MASK GENMASK(4, 0) |
| #define GSWIP_BM_QUEUE_GCTRL 0x04A |
| #define GSWIP_BM_QUEUE_GCTRL_GL_MOD BIT(10) |
| /* buffer management Port Configuration Register */ |
| #define GSWIP_BM_PCFGp(p) (0x080 + ((p) * 2)) |
| #define GSWIP_BM_PCFG_CNTEN BIT(0) /* RMON Counter Enable */ |
| #define GSWIP_BM_PCFG_IGCNT BIT(1) /* Ingres Special Tag RMON count */ |
| /* buffer management Port Control Register */ |
| #define GSWIP_BM_RMON_CTRLp(p) (0x81 + ((p) * 2)) |
| #define GSWIP_BM_CTRL_RMON_RAM1_RES BIT(0) /* Software Reset for RMON RAM 1 */ |
| #define GSWIP_BM_CTRL_RMON_RAM2_RES BIT(1) /* Software Reset for RMON RAM 2 */ |
| |
| /* PCE */ |
| #define GSWIP_PCE_TBL_KEY(x) (0x447 - (x)) |
| #define GSWIP_PCE_TBL_MASK 0x448 |
| #define GSWIP_PCE_TBL_VAL(x) (0x44D - (x)) |
| #define GSWIP_PCE_TBL_ADDR 0x44E |
| #define GSWIP_PCE_TBL_CTRL 0x44F |
| #define GSWIP_PCE_TBL_CTRL_BAS BIT(15) |
| #define GSWIP_PCE_TBL_CTRL_TYPE BIT(13) |
| #define GSWIP_PCE_TBL_CTRL_VLD BIT(12) |
| #define GSWIP_PCE_TBL_CTRL_KEYFORM BIT(11) |
| #define GSWIP_PCE_TBL_CTRL_GMAP_MASK GENMASK(10, 7) |
| #define GSWIP_PCE_TBL_CTRL_OPMOD_MASK GENMASK(6, 5) |
| #define GSWIP_PCE_TBL_CTRL_OPMOD_ADRD 0x00 |
| #define GSWIP_PCE_TBL_CTRL_OPMOD_ADWR 0x20 |
| #define GSWIP_PCE_TBL_CTRL_OPMOD_KSRD 0x40 |
| #define GSWIP_PCE_TBL_CTRL_OPMOD_KSWR 0x60 |
| #define GSWIP_PCE_TBL_CTRL_ADDR_MASK GENMASK(4, 0) |
| #define GSWIP_PCE_PMAP1 0x453 /* Monitoring port map */ |
| #define GSWIP_PCE_PMAP2 0x454 /* Default Multicast port map */ |
| #define GSWIP_PCE_PMAP3 0x455 /* Default Unknown Unicast port map */ |
| #define GSWIP_PCE_GCTRL_0 0x456 |
| #define GSWIP_PCE_GCTRL_0_MTFL BIT(0) /* MAC Table Flushing */ |
| #define GSWIP_PCE_GCTRL_0_MC_VALID BIT(3) |
| #define GSWIP_PCE_GCTRL_0_VLAN BIT(14) /* VLAN aware Switching */ |
| #define GSWIP_PCE_GCTRL_1 0x457 |
| #define GSWIP_PCE_GCTRL_1_MAC_GLOCK BIT(2) /* MAC Address table lock */ |
| #define GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD BIT(3) /* Mac address table lock forwarding mode */ |
| #define GSWIP_PCE_PCTRL_0p(p) (0x480 + ((p) * 0xA)) |
| #define GSWIP_PCE_PCTRL_0_TVM BIT(5) /* Transparent VLAN mode */ |
| #define GSWIP_PCE_PCTRL_0_VREP BIT(6) /* VLAN Replace Mode */ |
| #define GSWIP_PCE_PCTRL_0_INGRESS BIT(11) /* Accept special tag in ingress */ |
| #define GSWIP_PCE_PCTRL_0_PSTATE_LISTEN 0x0 |
| #define GSWIP_PCE_PCTRL_0_PSTATE_RX 0x1 |
| #define GSWIP_PCE_PCTRL_0_PSTATE_TX 0x2 |
| #define GSWIP_PCE_PCTRL_0_PSTATE_LEARNING 0x3 |
| #define GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING 0x7 |
| #define GSWIP_PCE_PCTRL_0_PSTATE_MASK GENMASK(2, 0) |
| #define GSWIP_PCE_VCTRL(p) (0x485 + ((p) * 0xA)) |
| #define GSWIP_PCE_VCTRL_UVR BIT(0) /* Unknown VLAN Rule */ |
| #define GSWIP_PCE_VCTRL_VIMR BIT(3) /* VLAN Ingress Member violation rule */ |
| #define GSWIP_PCE_VCTRL_VEMR BIT(4) /* VLAN Egress Member violation rule */ |
| #define GSWIP_PCE_VCTRL_VSR BIT(5) /* VLAN Security */ |
| #define GSWIP_PCE_VCTRL_VID0 BIT(6) /* Priority Tagged Rule */ |
| #define GSWIP_PCE_DEFPVID(p) (0x486 + ((p) * 0xA)) |
| |
| #define GSWIP_MAC_FLEN 0x8C5 |
| #define GSWIP_MAC_CTRL_0p(p) (0x903 + ((p) * 0xC)) |
| #define GSWIP_MAC_CTRL_0_PADEN BIT(8) |
| #define GSWIP_MAC_CTRL_0_FCS_EN BIT(7) |
| #define GSWIP_MAC_CTRL_0_FCON_MASK 0x0070 |
| #define GSWIP_MAC_CTRL_0_FCON_AUTO 0x0000 |
| #define GSWIP_MAC_CTRL_0_FCON_RX 0x0010 |
| #define GSWIP_MAC_CTRL_0_FCON_TX 0x0020 |
| #define GSWIP_MAC_CTRL_0_FCON_RXTX 0x0030 |
| #define GSWIP_MAC_CTRL_0_FCON_NONE 0x0040 |
| #define GSWIP_MAC_CTRL_0_FDUP_MASK 0x000C |
| #define GSWIP_MAC_CTRL_0_FDUP_AUTO 0x0000 |
| #define GSWIP_MAC_CTRL_0_FDUP_EN 0x0004 |
| #define GSWIP_MAC_CTRL_0_FDUP_DIS 0x000C |
| #define GSWIP_MAC_CTRL_0_GMII_MASK 0x0003 |
| #define GSWIP_MAC_CTRL_0_GMII_AUTO 0x0000 |
| #define GSWIP_MAC_CTRL_0_GMII_MII 0x0001 |
| #define GSWIP_MAC_CTRL_0_GMII_RGMII 0x0002 |
| #define GSWIP_MAC_CTRL_2p(p) (0x905 + ((p) * 0xC)) |
| #define GSWIP_MAC_CTRL_2_MLEN BIT(3) /* Maximum Untagged Frame Lnegth */ |
| |
| /* Ethernet Switch Fetch DMA Port Control Register */ |
| #define GSWIP_FDMA_PCTRLp(p) (0xA80 + ((p) * 0x6)) |
| #define GSWIP_FDMA_PCTRL_EN BIT(0) /* FDMA Port Enable */ |
| #define GSWIP_FDMA_PCTRL_STEN BIT(1) /* Special Tag Insertion Enable */ |
| #define GSWIP_FDMA_PCTRL_VLANMOD_MASK GENMASK(4, 3) /* VLAN Modification Control */ |
| #define GSWIP_FDMA_PCTRL_VLANMOD_SHIFT 3 /* VLAN Modification Control */ |
| #define GSWIP_FDMA_PCTRL_VLANMOD_DIS (0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) |
| #define GSWIP_FDMA_PCTRL_VLANMOD_PRIO (0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) |
| #define GSWIP_FDMA_PCTRL_VLANMOD_ID (0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) |
| #define GSWIP_FDMA_PCTRL_VLANMOD_BOTH (0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) |
| |
| /* Ethernet Switch Store DMA Port Control Register */ |
| #define GSWIP_SDMA_PCTRLp(p) (0xBC0 + ((p) * 0x6)) |
| #define GSWIP_SDMA_PCTRL_EN BIT(0) /* SDMA Port Enable */ |
| #define GSWIP_SDMA_PCTRL_FCEN BIT(1) /* Flow Control Enable */ |
| #define GSWIP_SDMA_PCTRL_PAUFWD BIT(3) /* Pause Frame Forwarding */ |
| |
| #define GSWIP_TABLE_ACTIVE_VLAN 0x01 |
| #define GSWIP_TABLE_VLAN_MAPPING 0x02 |
| #define GSWIP_TABLE_MAC_BRIDGE 0x0b |
| #define GSWIP_TABLE_MAC_BRIDGE_STATIC 0x01 /* Static not, aging entry */ |
| |
| #define XRX200_GPHY_FW_ALIGN (16 * 1024) |
| |
| struct gswip_hw_info { |
| int max_ports; |
| int cpu_port; |
| }; |
| |
| struct xway_gphy_match_data { |
| char *fe_firmware_name; |
| char *ge_firmware_name; |
| }; |
| |
| struct gswip_gphy_fw { |
| struct clk *clk_gate; |
| struct reset_control *reset; |
| u32 fw_addr_offset; |
| char *fw_name; |
| }; |
| |
| struct gswip_vlan { |
| struct net_device *bridge; |
| u16 vid; |
| u8 fid; |
| }; |
| |
| struct gswip_priv { |
| __iomem void *gswip; |
| __iomem void *mdio; |
| __iomem void *mii; |
| const struct gswip_hw_info *hw_info; |
| const struct xway_gphy_match_data *gphy_fw_name_cfg; |
| struct dsa_switch *ds; |
| struct device *dev; |
| struct regmap *rcu_regmap; |
| struct gswip_vlan vlans[64]; |
| int num_gphy_fw; |
| struct gswip_gphy_fw *gphy_fw; |
| u32 port_vlan_filter; |
| }; |
| |
| struct gswip_pce_table_entry { |
| u16 index; // PCE_TBL_ADDR.ADDR = pData->table_index |
| u16 table; // PCE_TBL_CTRL.ADDR = pData->table |
| u16 key[8]; |
| u16 val[5]; |
| u16 mask; |
| u8 gmap; |
| bool type; |
| bool valid; |
| bool key_mode; |
| }; |
| |
| struct gswip_rmon_cnt_desc { |
| unsigned int size; |
| unsigned int offset; |
| const char *name; |
| }; |
| |
| #define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name} |
| |
| static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = { |
| /** Receive Packet Count (only packets that are accepted and not discarded). */ |
| MIB_DESC(1, 0x1F, "RxGoodPkts"), |
| MIB_DESC(1, 0x23, "RxUnicastPkts"), |
| MIB_DESC(1, 0x22, "RxMulticastPkts"), |
| MIB_DESC(1, 0x21, "RxFCSErrorPkts"), |
| MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"), |
| MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"), |
| MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"), |
| MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"), |
| MIB_DESC(1, 0x20, "RxGoodPausePkts"), |
| MIB_DESC(1, 0x1A, "RxAlignErrorPkts"), |
| MIB_DESC(1, 0x12, "Rx64BytePkts"), |
| MIB_DESC(1, 0x13, "Rx127BytePkts"), |
| MIB_DESC(1, 0x14, "Rx255BytePkts"), |
| MIB_DESC(1, 0x15, "Rx511BytePkts"), |
| MIB_DESC(1, 0x16, "Rx1023BytePkts"), |
| /** Receive Size 1024-1522 (or more, if configured) Packet Count. */ |
| MIB_DESC(1, 0x17, "RxMaxBytePkts"), |
| MIB_DESC(1, 0x18, "RxDroppedPkts"), |
| MIB_DESC(1, 0x19, "RxFilteredPkts"), |
| MIB_DESC(2, 0x24, "RxGoodBytes"), |
| MIB_DESC(2, 0x26, "RxBadBytes"), |
| MIB_DESC(1, 0x11, "TxAcmDroppedPkts"), |
| MIB_DESC(1, 0x0C, "TxGoodPkts"), |
| MIB_DESC(1, 0x06, "TxUnicastPkts"), |
| MIB_DESC(1, 0x07, "TxMulticastPkts"), |
| MIB_DESC(1, 0x00, "Tx64BytePkts"), |
| MIB_DESC(1, 0x01, "Tx127BytePkts"), |
| MIB_DESC(1, 0x02, "Tx255BytePkts"), |
| MIB_DESC(1, 0x03, "Tx511BytePkts"), |
| MIB_DESC(1, 0x04, "Tx1023BytePkts"), |
| /** Transmit Size 1024-1522 (or more, if configured) Packet Count. */ |
| MIB_DESC(1, 0x05, "TxMaxBytePkts"), |
| MIB_DESC(1, 0x08, "TxSingleCollCount"), |
| MIB_DESC(1, 0x09, "TxMultCollCount"), |
| MIB_DESC(1, 0x0A, "TxLateCollCount"), |
| MIB_DESC(1, 0x0B, "TxExcessCollCount"), |
| MIB_DESC(1, 0x0D, "TxPauseCount"), |
| MIB_DESC(1, 0x10, "TxDroppedPkts"), |
| MIB_DESC(2, 0x0E, "TxGoodBytes"), |
| }; |
| |
| static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset) |
| { |
| return __raw_readl(priv->gswip + (offset * 4)); |
| } |
| |
| static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset) |
| { |
| __raw_writel(val, priv->gswip + (offset * 4)); |
| } |
| |
| static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set, |
| u32 offset) |
| { |
| u32 val = gswip_switch_r(priv, offset); |
| |
| val &= ~(clear); |
| val |= set; |
| gswip_switch_w(priv, val, offset); |
| } |
| |
| static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset, |
| u32 cleared) |
| { |
| u32 val; |
| |
| return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val, |
| (val & cleared) == 0, 20, 50000); |
| } |
| |
| static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset) |
| { |
| return __raw_readl(priv->mdio + (offset * 4)); |
| } |
| |
| static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset) |
| { |
| __raw_writel(val, priv->mdio + (offset * 4)); |
| } |
| |
| static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set, |
| u32 offset) |
| { |
| u32 val = gswip_mdio_r(priv, offset); |
| |
| val &= ~(clear); |
| val |= set; |
| gswip_mdio_w(priv, val, offset); |
| } |
| |
| static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset) |
| { |
| return __raw_readl(priv->mii + (offset * 4)); |
| } |
| |
| static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset) |
| { |
| __raw_writel(val, priv->mii + (offset * 4)); |
| } |
| |
| static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set, |
| u32 offset) |
| { |
| u32 val = gswip_mii_r(priv, offset); |
| |
| val &= ~(clear); |
| val |= set; |
| gswip_mii_w(priv, val, offset); |
| } |
| |
| static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set, |
| int port) |
| { |
| /* There's no MII_CFG register for the CPU port */ |
| if (!dsa_is_cpu_port(priv->ds, port)) |
| gswip_mii_mask(priv, clear, set, GSWIP_MII_CFGp(port)); |
| } |
| |
| static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set, |
| int port) |
| { |
| switch (port) { |
| case 0: |
| gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0); |
| break; |
| case 1: |
| gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1); |
| break; |
| case 5: |
| gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5); |
| break; |
| } |
| } |
| |
| static int gswip_mdio_poll(struct gswip_priv *priv) |
| { |
| int cnt = 100; |
| |
| while (likely(cnt--)) { |
| u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL); |
| |
| if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0) |
| return 0; |
| usleep_range(20, 40); |
| } |
| |
| return -ETIMEDOUT; |
| } |
| |
| static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val) |
| { |
| struct gswip_priv *priv = bus->priv; |
| int err; |
| |
| err = gswip_mdio_poll(priv); |
| if (err) { |
| dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); |
| return err; |
| } |
| |
| gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE); |
| gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR | |
| ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | |
| (reg & GSWIP_MDIO_CTRL_REGAD_MASK), |
| GSWIP_MDIO_CTRL); |
| |
| return 0; |
| } |
| |
| static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg) |
| { |
| struct gswip_priv *priv = bus->priv; |
| int err; |
| |
| err = gswip_mdio_poll(priv); |
| if (err) { |
| dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); |
| return err; |
| } |
| |
| gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD | |
| ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | |
| (reg & GSWIP_MDIO_CTRL_REGAD_MASK), |
| GSWIP_MDIO_CTRL); |
| |
| err = gswip_mdio_poll(priv); |
| if (err) { |
| dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); |
| return err; |
| } |
| |
| return gswip_mdio_r(priv, GSWIP_MDIO_READ); |
| } |
| |
| static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np) |
| { |
| struct dsa_switch *ds = priv->ds; |
| int err; |
| |
| ds->slave_mii_bus = mdiobus_alloc(); |
| if (!ds->slave_mii_bus) |
| return -ENOMEM; |
| |
| ds->slave_mii_bus->priv = priv; |
| ds->slave_mii_bus->read = gswip_mdio_rd; |
| ds->slave_mii_bus->write = gswip_mdio_wr; |
| ds->slave_mii_bus->name = "lantiq,xrx200-mdio"; |
| snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii", |
| dev_name(priv->dev)); |
| ds->slave_mii_bus->parent = priv->dev; |
| ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask; |
| |
| err = of_mdiobus_register(ds->slave_mii_bus, mdio_np); |
| if (err) |
| mdiobus_free(ds->slave_mii_bus); |
| |
| return err; |
| } |
| |
| static int gswip_pce_table_entry_read(struct gswip_priv *priv, |
| struct gswip_pce_table_entry *tbl) |
| { |
| int i; |
| int err; |
| u16 crtl; |
| u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSRD : |
| GSWIP_PCE_TBL_CTRL_OPMOD_ADRD; |
| |
| err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, |
| GSWIP_PCE_TBL_CTRL_BAS); |
| if (err) |
| return err; |
| |
| gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); |
| gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | |
| GSWIP_PCE_TBL_CTRL_OPMOD_MASK, |
| tbl->table | addr_mode | GSWIP_PCE_TBL_CTRL_BAS, |
| GSWIP_PCE_TBL_CTRL); |
| |
| err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, |
| GSWIP_PCE_TBL_CTRL_BAS); |
| if (err) |
| return err; |
| |
| for (i = 0; i < ARRAY_SIZE(tbl->key); i++) |
| tbl->key[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_KEY(i)); |
| |
| for (i = 0; i < ARRAY_SIZE(tbl->val); i++) |
| tbl->val[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_VAL(i)); |
| |
| tbl->mask = gswip_switch_r(priv, GSWIP_PCE_TBL_MASK); |
| |
| crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); |
| |
| tbl->type = !!(crtl & GSWIP_PCE_TBL_CTRL_TYPE); |
| tbl->valid = !!(crtl & GSWIP_PCE_TBL_CTRL_VLD); |
| tbl->gmap = (crtl & GSWIP_PCE_TBL_CTRL_GMAP_MASK) >> 7; |
| |
| return 0; |
| } |
| |
| static int gswip_pce_table_entry_write(struct gswip_priv *priv, |
| struct gswip_pce_table_entry *tbl) |
| { |
| int i; |
| int err; |
| u16 crtl; |
| u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSWR : |
| GSWIP_PCE_TBL_CTRL_OPMOD_ADWR; |
| |
| err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, |
| GSWIP_PCE_TBL_CTRL_BAS); |
| if (err) |
| return err; |
| |
| gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); |
| gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | |
| GSWIP_PCE_TBL_CTRL_OPMOD_MASK, |
| tbl->table | addr_mode, |
| GSWIP_PCE_TBL_CTRL); |
| |
| for (i = 0; i < ARRAY_SIZE(tbl->key); i++) |
| gswip_switch_w(priv, tbl->key[i], GSWIP_PCE_TBL_KEY(i)); |
| |
| for (i = 0; i < ARRAY_SIZE(tbl->val); i++) |
| gswip_switch_w(priv, tbl->val[i], GSWIP_PCE_TBL_VAL(i)); |
| |
| gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | |
| GSWIP_PCE_TBL_CTRL_OPMOD_MASK, |
| tbl->table | addr_mode, |
| GSWIP_PCE_TBL_CTRL); |
| |
| gswip_switch_w(priv, tbl->mask, GSWIP_PCE_TBL_MASK); |
| |
| crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); |
| crtl &= ~(GSWIP_PCE_TBL_CTRL_TYPE | GSWIP_PCE_TBL_CTRL_VLD | |
| GSWIP_PCE_TBL_CTRL_GMAP_MASK); |
| if (tbl->type) |
| crtl |= GSWIP_PCE_TBL_CTRL_TYPE; |
| if (tbl->valid) |
| crtl |= GSWIP_PCE_TBL_CTRL_VLD; |
| crtl |= (tbl->gmap << 7) & GSWIP_PCE_TBL_CTRL_GMAP_MASK; |
| crtl |= GSWIP_PCE_TBL_CTRL_BAS; |
| gswip_switch_w(priv, crtl, GSWIP_PCE_TBL_CTRL); |
| |
| return gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, |
| GSWIP_PCE_TBL_CTRL_BAS); |
| } |
| |
| /* Add the LAN port into a bridge with the CPU port by |
| * default. This prevents automatic forwarding of |
| * packages between the LAN ports when no explicit |
| * bridge is configured. |
| */ |
| static int gswip_add_single_port_br(struct gswip_priv *priv, int port, bool add) |
| { |
| struct gswip_pce_table_entry vlan_active = {0,}; |
| struct gswip_pce_table_entry vlan_mapping = {0,}; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| int err; |
| |
| if (port >= max_ports) { |
| dev_err(priv->dev, "single port for %i supported\n", port); |
| return -EIO; |
| } |
| |
| vlan_active.index = port + 1; |
| vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; |
| vlan_active.key[0] = 0; /* vid */ |
| vlan_active.val[0] = port + 1 /* fid */; |
| vlan_active.valid = add; |
| err = gswip_pce_table_entry_write(priv, &vlan_active); |
| if (err) { |
| dev_err(priv->dev, "failed to write active VLAN: %d\n", err); |
| return err; |
| } |
| |
| if (!add) |
| return 0; |
| |
| vlan_mapping.index = port + 1; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| vlan_mapping.val[0] = 0 /* vid */; |
| vlan_mapping.val[1] = BIT(port) | BIT(cpu_port); |
| vlan_mapping.val[2] = 0; |
| err = gswip_pce_table_entry_write(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static int gswip_port_enable(struct dsa_switch *ds, int port, |
| struct phy_device *phydev) |
| { |
| struct gswip_priv *priv = ds->priv; |
| int err; |
| |
| if (!dsa_is_user_port(ds, port)) |
| return 0; |
| |
| if (!dsa_is_cpu_port(ds, port)) { |
| err = gswip_add_single_port_br(priv, port, true); |
| if (err) |
| return err; |
| } |
| |
| /* RMON Counter Enable for port */ |
| gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port)); |
| |
| /* enable port fetch/store dma & VLAN Modification */ |
| gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN | |
| GSWIP_FDMA_PCTRL_VLANMOD_BOTH, |
| GSWIP_FDMA_PCTRLp(port)); |
| gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, |
| GSWIP_SDMA_PCTRLp(port)); |
| |
| if (!dsa_is_cpu_port(ds, port)) { |
| u32 mdio_phy = 0; |
| |
| if (phydev) |
| mdio_phy = phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK; |
| |
| gswip_mdio_mask(priv, GSWIP_MDIO_PHY_ADDR_MASK, mdio_phy, |
| GSWIP_MDIO_PHYp(port)); |
| } |
| |
| return 0; |
| } |
| |
| static void gswip_port_disable(struct dsa_switch *ds, int port) |
| { |
| struct gswip_priv *priv = ds->priv; |
| |
| if (!dsa_is_user_port(ds, port)) |
| return; |
| |
| gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0, |
| GSWIP_FDMA_PCTRLp(port)); |
| gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, |
| GSWIP_SDMA_PCTRLp(port)); |
| } |
| |
| static int gswip_pce_load_microcode(struct gswip_priv *priv) |
| { |
| int i; |
| int err; |
| |
| gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | |
| GSWIP_PCE_TBL_CTRL_OPMOD_MASK, |
| GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL); |
| gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK); |
| |
| for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) { |
| gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR); |
| gswip_switch_w(priv, gswip_pce_microcode[i].val_0, |
| GSWIP_PCE_TBL_VAL(0)); |
| gswip_switch_w(priv, gswip_pce_microcode[i].val_1, |
| GSWIP_PCE_TBL_VAL(1)); |
| gswip_switch_w(priv, gswip_pce_microcode[i].val_2, |
| GSWIP_PCE_TBL_VAL(2)); |
| gswip_switch_w(priv, gswip_pce_microcode[i].val_3, |
| GSWIP_PCE_TBL_VAL(3)); |
| |
| /* start the table access: */ |
| gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS, |
| GSWIP_PCE_TBL_CTRL); |
| err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, |
| GSWIP_PCE_TBL_CTRL_BAS); |
| if (err) |
| return err; |
| } |
| |
| /* tell the switch that the microcode is loaded */ |
| gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID, |
| GSWIP_PCE_GCTRL_0); |
| |
| return 0; |
| } |
| |
| static int gswip_port_vlan_filtering(struct dsa_switch *ds, int port, |
| bool vlan_filtering, |
| struct switchdev_trans *trans) |
| { |
| struct gswip_priv *priv = ds->priv; |
| |
| /* Do not allow changing the VLAN filtering options while in bridge */ |
| if (switchdev_trans_ph_prepare(trans)) { |
| struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; |
| |
| if (!bridge) |
| return 0; |
| |
| if (!!(priv->port_vlan_filter & BIT(port)) != vlan_filtering) |
| return -EIO; |
| |
| return 0; |
| } |
| |
| if (vlan_filtering) { |
| /* Use port based VLAN tag */ |
| gswip_switch_mask(priv, |
| GSWIP_PCE_VCTRL_VSR, |
| GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | |
| GSWIP_PCE_VCTRL_VEMR, |
| GSWIP_PCE_VCTRL(port)); |
| gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_TVM, 0, |
| GSWIP_PCE_PCTRL_0p(port)); |
| } else { |
| /* Use port based VLAN tag */ |
| gswip_switch_mask(priv, |
| GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | |
| GSWIP_PCE_VCTRL_VEMR, |
| GSWIP_PCE_VCTRL_VSR, |
| GSWIP_PCE_VCTRL(port)); |
| gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_TVM, |
| GSWIP_PCE_PCTRL_0p(port)); |
| } |
| |
| return 0; |
| } |
| |
| static int gswip_setup(struct dsa_switch *ds) |
| { |
| struct gswip_priv *priv = ds->priv; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| int i; |
| int err; |
| |
| gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES); |
| usleep_range(5000, 10000); |
| gswip_switch_w(priv, 0, GSWIP_SWRES); |
| |
| /* disable port fetch/store dma on all ports */ |
| for (i = 0; i < priv->hw_info->max_ports; i++) { |
| struct switchdev_trans trans; |
| |
| /* Skip the prepare phase, this shouldn't return an error |
| * during setup. |
| */ |
| trans.ph_prepare = false; |
| |
| gswip_port_disable(ds, i); |
| gswip_port_vlan_filtering(ds, i, false, &trans); |
| } |
| |
| /* enable Switch */ |
| gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB); |
| |
| err = gswip_pce_load_microcode(priv); |
| if (err) { |
| dev_err(priv->dev, "writing PCE microcode failed, %i", err); |
| return err; |
| } |
| |
| /* Default unknown Broadcast/Multicast/Unicast port maps */ |
| gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1); |
| gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2); |
| gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3); |
| |
| /* Deactivate MDIO PHY auto polling. Some PHYs as the AR8030 have an |
| * interoperability problem with this auto polling mechanism because |
| * their status registers think that the link is in a different state |
| * than it actually is. For the AR8030 it has the BMSR_ESTATEN bit set |
| * as well as ESTATUS_1000_TFULL and ESTATUS_1000_XFULL. This makes the |
| * auto polling state machine consider the link being negotiated with |
| * 1Gbit/s. Since the PHY itself is a Fast Ethernet RMII PHY this leads |
| * to the switch port being completely dead (RX and TX are both not |
| * working). |
| * Also with various other PHY / port combinations (PHY11G GPHY, PHY22F |
| * GPHY, external RGMII PEF7071/7072) any traffic would stop. Sometimes |
| * it would work fine for a few minutes to hours and then stop, on |
| * other device it would no traffic could be sent or received at all. |
| * Testing shows that when PHY auto polling is disabled these problems |
| * go away. |
| */ |
| gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0); |
| |
| /* Configure the MDIO Clock 2.5 MHz */ |
| gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1); |
| |
| /* Disable the xMII interface and clear it's isolation bit */ |
| for (i = 0; i < priv->hw_info->max_ports; i++) |
| gswip_mii_mask_cfg(priv, |
| GSWIP_MII_CFG_EN | GSWIP_MII_CFG_ISOLATE, |
| 0, i); |
| |
| /* enable special tag insertion on cpu port */ |
| gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN, |
| GSWIP_FDMA_PCTRLp(cpu_port)); |
| |
| /* accept special tag in ingress direction */ |
| gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS, |
| GSWIP_PCE_PCTRL_0p(cpu_port)); |
| |
| gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN, |
| GSWIP_MAC_CTRL_2p(cpu_port)); |
| gswip_switch_w(priv, VLAN_ETH_FRAME_LEN + 8 + ETH_FCS_LEN, |
| GSWIP_MAC_FLEN); |
| gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD, |
| GSWIP_BM_QUEUE_GCTRL); |
| |
| /* VLAN aware Switching */ |
| gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0); |
| |
| /* Flush MAC Table */ |
| gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MTFL, GSWIP_PCE_GCTRL_0); |
| |
| err = gswip_switch_r_timeout(priv, GSWIP_PCE_GCTRL_0, |
| GSWIP_PCE_GCTRL_0_MTFL); |
| if (err) { |
| dev_err(priv->dev, "MAC flushing didn't finish\n"); |
| return err; |
| } |
| |
| gswip_port_enable(ds, cpu_port, NULL); |
| return 0; |
| } |
| |
| static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds, |
| int port, |
| enum dsa_tag_protocol mp) |
| { |
| return DSA_TAG_PROTO_GSWIP; |
| } |
| |
| static int gswip_vlan_active_create(struct gswip_priv *priv, |
| struct net_device *bridge, |
| int fid, u16 vid) |
| { |
| struct gswip_pce_table_entry vlan_active = {0,}; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| int idx = -1; |
| int err; |
| int i; |
| |
| /* Look for a free slot */ |
| for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (!priv->vlans[i].bridge) { |
| idx = i; |
| break; |
| } |
| } |
| |
| if (idx == -1) |
| return -ENOSPC; |
| |
| if (fid == -1) |
| fid = idx; |
| |
| vlan_active.index = idx; |
| vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; |
| vlan_active.key[0] = vid; |
| vlan_active.val[0] = fid; |
| vlan_active.valid = true; |
| |
| err = gswip_pce_table_entry_write(priv, &vlan_active); |
| if (err) { |
| dev_err(priv->dev, "failed to write active VLAN: %d\n", err); |
| return err; |
| } |
| |
| priv->vlans[idx].bridge = bridge; |
| priv->vlans[idx].vid = vid; |
| priv->vlans[idx].fid = fid; |
| |
| return idx; |
| } |
| |
| static int gswip_vlan_active_remove(struct gswip_priv *priv, int idx) |
| { |
| struct gswip_pce_table_entry vlan_active = {0,}; |
| int err; |
| |
| vlan_active.index = idx; |
| vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; |
| vlan_active.valid = false; |
| err = gswip_pce_table_entry_write(priv, &vlan_active); |
| if (err) |
| dev_err(priv->dev, "failed to delete active VLAN: %d\n", err); |
| priv->vlans[idx].bridge = NULL; |
| |
| return err; |
| } |
| |
| static int gswip_vlan_add_unaware(struct gswip_priv *priv, |
| struct net_device *bridge, int port) |
| { |
| struct gswip_pce_table_entry vlan_mapping = {0,}; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| bool active_vlan_created = false; |
| int idx = -1; |
| int i; |
| int err; |
| |
| /* Check if there is already a page for this bridge */ |
| for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (priv->vlans[i].bridge == bridge) { |
| idx = i; |
| break; |
| } |
| } |
| |
| /* If this bridge is not programmed yet, add a Active VLAN table |
| * entry in a free slot and prepare the VLAN mapping table entry. |
| */ |
| if (idx == -1) { |
| idx = gswip_vlan_active_create(priv, bridge, -1, 0); |
| if (idx < 0) |
| return idx; |
| active_vlan_created = true; |
| |
| vlan_mapping.index = idx; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| /* VLAN ID byte, maps to the VLAN ID of vlan active table */ |
| vlan_mapping.val[0] = 0; |
| } else { |
| /* Read the existing VLAN mapping entry from the switch */ |
| vlan_mapping.index = idx; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| err = gswip_pce_table_entry_read(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to read VLAN mapping: %d\n", |
| err); |
| return err; |
| } |
| } |
| |
| /* Update the VLAN mapping entry and write it to the switch */ |
| vlan_mapping.val[1] |= BIT(cpu_port); |
| vlan_mapping.val[1] |= BIT(port); |
| err = gswip_pce_table_entry_write(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); |
| /* In case an Active VLAN was creaetd delete it again */ |
| if (active_vlan_created) |
| gswip_vlan_active_remove(priv, idx); |
| return err; |
| } |
| |
| gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); |
| return 0; |
| } |
| |
| static int gswip_vlan_add_aware(struct gswip_priv *priv, |
| struct net_device *bridge, int port, |
| u16 vid, bool untagged, |
| bool pvid) |
| { |
| struct gswip_pce_table_entry vlan_mapping = {0,}; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| bool active_vlan_created = false; |
| int idx = -1; |
| int fid = -1; |
| int i; |
| int err; |
| |
| /* Check if there is already a page for this bridge */ |
| for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (priv->vlans[i].bridge == bridge) { |
| if (fid != -1 && fid != priv->vlans[i].fid) |
| dev_err(priv->dev, "one bridge with multiple flow ids\n"); |
| fid = priv->vlans[i].fid; |
| if (priv->vlans[i].vid == vid) { |
| idx = i; |
| break; |
| } |
| } |
| } |
| |
| /* If this bridge is not programmed yet, add a Active VLAN table |
| * entry in a free slot and prepare the VLAN mapping table entry. |
| */ |
| if (idx == -1) { |
| idx = gswip_vlan_active_create(priv, bridge, fid, vid); |
| if (idx < 0) |
| return idx; |
| active_vlan_created = true; |
| |
| vlan_mapping.index = idx; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| /* VLAN ID byte, maps to the VLAN ID of vlan active table */ |
| vlan_mapping.val[0] = vid; |
| } else { |
| /* Read the existing VLAN mapping entry from the switch */ |
| vlan_mapping.index = idx; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| err = gswip_pce_table_entry_read(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to read VLAN mapping: %d\n", |
| err); |
| return err; |
| } |
| } |
| |
| vlan_mapping.val[0] = vid; |
| /* Update the VLAN mapping entry and write it to the switch */ |
| vlan_mapping.val[1] |= BIT(cpu_port); |
| vlan_mapping.val[2] |= BIT(cpu_port); |
| vlan_mapping.val[1] |= BIT(port); |
| if (untagged) |
| vlan_mapping.val[2] &= ~BIT(port); |
| else |
| vlan_mapping.val[2] |= BIT(port); |
| err = gswip_pce_table_entry_write(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); |
| /* In case an Active VLAN was creaetd delete it again */ |
| if (active_vlan_created) |
| gswip_vlan_active_remove(priv, idx); |
| return err; |
| } |
| |
| if (pvid) |
| gswip_switch_w(priv, idx, GSWIP_PCE_DEFPVID(port)); |
| |
| return 0; |
| } |
| |
| static int gswip_vlan_remove(struct gswip_priv *priv, |
| struct net_device *bridge, int port, |
| u16 vid, bool pvid, bool vlan_aware) |
| { |
| struct gswip_pce_table_entry vlan_mapping = {0,}; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| int idx = -1; |
| int i; |
| int err; |
| |
| /* Check if there is already a page for this bridge */ |
| for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (priv->vlans[i].bridge == bridge && |
| (!vlan_aware || priv->vlans[i].vid == vid)) { |
| idx = i; |
| break; |
| } |
| } |
| |
| if (idx == -1) { |
| dev_err(priv->dev, "bridge to leave does not exists\n"); |
| return -ENOENT; |
| } |
| |
| vlan_mapping.index = idx; |
| vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; |
| err = gswip_pce_table_entry_read(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to read VLAN mapping: %d\n", err); |
| return err; |
| } |
| |
| vlan_mapping.val[1] &= ~BIT(port); |
| vlan_mapping.val[2] &= ~BIT(port); |
| err = gswip_pce_table_entry_write(priv, &vlan_mapping); |
| if (err) { |
| dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); |
| return err; |
| } |
| |
| /* In case all ports are removed from the bridge, remove the VLAN */ |
| if ((vlan_mapping.val[1] & ~BIT(cpu_port)) == 0) { |
| err = gswip_vlan_active_remove(priv, idx); |
| if (err) { |
| dev_err(priv->dev, "failed to write active VLAN: %d\n", |
| err); |
| return err; |
| } |
| } |
| |
| /* GSWIP 2.2 (GRX300) and later program here the VID directly. */ |
| if (pvid) |
| gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); |
| |
| return 0; |
| } |
| |
| static int gswip_port_bridge_join(struct dsa_switch *ds, int port, |
| struct net_device *bridge) |
| { |
| struct gswip_priv *priv = ds->priv; |
| int err; |
| |
| /* When the bridge uses VLAN filtering we have to configure VLAN |
| * specific bridges. No bridge is configured here. |
| */ |
| if (!br_vlan_enabled(bridge)) { |
| err = gswip_vlan_add_unaware(priv, bridge, port); |
| if (err) |
| return err; |
| priv->port_vlan_filter &= ~BIT(port); |
| } else { |
| priv->port_vlan_filter |= BIT(port); |
| } |
| return gswip_add_single_port_br(priv, port, false); |
| } |
| |
| static void gswip_port_bridge_leave(struct dsa_switch *ds, int port, |
| struct net_device *bridge) |
| { |
| struct gswip_priv *priv = ds->priv; |
| |
| gswip_add_single_port_br(priv, port, true); |
| |
| /* When the bridge uses VLAN filtering we have to configure VLAN |
| * specific bridges. No bridge is configured here. |
| */ |
| if (!br_vlan_enabled(bridge)) |
| gswip_vlan_remove(priv, bridge, port, 0, true, false); |
| } |
| |
| static int gswip_port_vlan_prepare(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; |
| unsigned int max_ports = priv->hw_info->max_ports; |
| u16 vid; |
| int i; |
| int pos = max_ports; |
| |
| /* We only support VLAN filtering on bridges */ |
| if (!dsa_is_cpu_port(ds, port) && !bridge) |
| return -EOPNOTSUPP; |
| |
| for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) { |
| int idx = -1; |
| |
| /* Check if there is already a page for this VLAN */ |
| for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (priv->vlans[i].bridge == bridge && |
| priv->vlans[i].vid == vid) { |
| idx = i; |
| break; |
| } |
| } |
| |
| /* If this VLAN is not programmed yet, we have to reserve |
| * one entry in the VLAN table. Make sure we start at the |
| * next position round. |
| */ |
| if (idx == -1) { |
| /* Look for a free slot */ |
| for (; pos < ARRAY_SIZE(priv->vlans); pos++) { |
| if (!priv->vlans[pos].bridge) { |
| idx = pos; |
| pos++; |
| break; |
| } |
| } |
| |
| if (idx == -1) |
| return -ENOSPC; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void gswip_port_vlan_add(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; |
| bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; |
| bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; |
| u16 vid; |
| |
| /* We have to receive all packets on the CPU port and should not |
| * do any VLAN filtering here. This is also called with bridge |
| * NULL and then we do not know for which bridge to configure |
| * this. |
| */ |
| if (dsa_is_cpu_port(ds, port)) |
| return; |
| |
| for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) |
| gswip_vlan_add_aware(priv, bridge, port, vid, untagged, pvid); |
| } |
| |
| static int gswip_port_vlan_del(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; |
| bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; |
| u16 vid; |
| int err; |
| |
| /* We have to receive all packets on the CPU port and should not |
| * do any VLAN filtering here. This is also called with bridge |
| * NULL and then we do not know for which bridge to configure |
| * this. |
| */ |
| if (dsa_is_cpu_port(ds, port)) |
| return 0; |
| |
| for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) { |
| err = gswip_vlan_remove(priv, bridge, port, vid, pvid, true); |
| if (err) |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static void gswip_port_fast_age(struct dsa_switch *ds, int port) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct gswip_pce_table_entry mac_bridge = {0,}; |
| int i; |
| int err; |
| |
| for (i = 0; i < 2048; i++) { |
| mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; |
| mac_bridge.index = i; |
| |
| err = gswip_pce_table_entry_read(priv, &mac_bridge); |
| if (err) { |
| dev_err(priv->dev, "failed to read mac bridge: %d\n", |
| err); |
| return; |
| } |
| |
| if (!mac_bridge.valid) |
| continue; |
| |
| if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) |
| continue; |
| |
| if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) != port) |
| continue; |
| |
| mac_bridge.valid = false; |
| err = gswip_pce_table_entry_write(priv, &mac_bridge); |
| if (err) { |
| dev_err(priv->dev, "failed to write mac bridge: %d\n", |
| err); |
| return; |
| } |
| } |
| } |
| |
| static void gswip_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) |
| { |
| struct gswip_priv *priv = ds->priv; |
| u32 stp_state; |
| |
| switch (state) { |
| case BR_STATE_DISABLED: |
| gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, |
| GSWIP_SDMA_PCTRLp(port)); |
| return; |
| case BR_STATE_BLOCKING: |
| case BR_STATE_LISTENING: |
| stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LISTEN; |
| break; |
| case BR_STATE_LEARNING: |
| stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LEARNING; |
| break; |
| case BR_STATE_FORWARDING: |
| stp_state = GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING; |
| break; |
| default: |
| dev_err(priv->dev, "invalid STP state: %d\n", state); |
| return; |
| } |
| |
| gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, |
| GSWIP_SDMA_PCTRLp(port)); |
| gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_PSTATE_MASK, stp_state, |
| GSWIP_PCE_PCTRL_0p(port)); |
| } |
| |
| static int gswip_port_fdb(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid, bool add) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; |
| struct gswip_pce_table_entry mac_bridge = {0,}; |
| unsigned int cpu_port = priv->hw_info->cpu_port; |
| int fid = -1; |
| int i; |
| int err; |
| |
| if (!bridge) |
| return -EINVAL; |
| |
| for (i = cpu_port; i < ARRAY_SIZE(priv->vlans); i++) { |
| if (priv->vlans[i].bridge == bridge) { |
| fid = priv->vlans[i].fid; |
| break; |
| } |
| } |
| |
| if (fid == -1) { |
| dev_err(priv->dev, "Port not part of a bridge\n"); |
| return -EINVAL; |
| } |
| |
| mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; |
| mac_bridge.key_mode = true; |
| mac_bridge.key[0] = addr[5] | (addr[4] << 8); |
| mac_bridge.key[1] = addr[3] | (addr[2] << 8); |
| mac_bridge.key[2] = addr[1] | (addr[0] << 8); |
| mac_bridge.key[3] = fid; |
| mac_bridge.val[0] = add ? BIT(port) : 0; /* port map */ |
| mac_bridge.val[1] = GSWIP_TABLE_MAC_BRIDGE_STATIC; |
| mac_bridge.valid = add; |
| |
| err = gswip_pce_table_entry_write(priv, &mac_bridge); |
| if (err) |
| dev_err(priv->dev, "failed to write mac bridge: %d\n", err); |
| |
| return err; |
| } |
| |
| static int gswip_port_fdb_add(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| return gswip_port_fdb(ds, port, addr, vid, true); |
| } |
| |
| static int gswip_port_fdb_del(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| return gswip_port_fdb(ds, port, addr, vid, false); |
| } |
| |
| static int gswip_port_fdb_dump(struct dsa_switch *ds, int port, |
| dsa_fdb_dump_cb_t *cb, void *data) |
| { |
| struct gswip_priv *priv = ds->priv; |
| struct gswip_pce_table_entry mac_bridge = {0,}; |
| unsigned char addr[6]; |
| int i; |
| int err; |
| |
| for (i = 0; i < 2048; i++) { |
| mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; |
| mac_bridge.index = i; |
| |
| err = gswip_pce_table_entry_read(priv, &mac_bridge); |
| if (err) { |
| dev_err(priv->dev, "failed to write mac bridge: %d\n", |
| err); |
| return err; |
| } |
| |
| if (!mac_bridge.valid) |
| continue; |
| |
| addr[5] = mac_bridge.key[0] & 0xff; |
| addr[4] = (mac_bridge.key[0] >> 8) & 0xff; |
| addr[3] = mac_bridge.key[1] & 0xff; |
| addr[2] = (mac_bridge.key[1] >> 8) & 0xff; |
| addr[1] = mac_bridge.key[2] & 0xff; |
| addr[0] = (mac_bridge.key[2] >> 8) & 0xff; |
| if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) { |
| if (mac_bridge.val[0] & BIT(port)) { |
| err = cb(addr, 0, true, data); |
| if (err) |
| return err; |
| } |
| } else { |
| if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) == port) { |
| err = cb(addr, 0, false, data); |
| if (err) |
| return err; |
| } |
| } |
| } |
| return 0; |
| } |
| |
| static void gswip_phylink_validate(struct dsa_switch *ds, int port, |
| unsigned long *supported, |
| struct phylink_link_state *state) |
| { |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; |
| |
| switch (port) { |
| case 0: |
| case 1: |
| if (!phy_interface_mode_is_rgmii(state->interface) && |
| state->interface != PHY_INTERFACE_MODE_MII && |
| state->interface != PHY_INTERFACE_MODE_REVMII && |
| state->interface != PHY_INTERFACE_MODE_RMII) |
| goto unsupported; |
| break; |
| case 2: |
| case 3: |
| case 4: |
| if (state->interface != PHY_INTERFACE_MODE_INTERNAL) |
| goto unsupported; |
| break; |
| case 5: |
| if (!phy_interface_mode_is_rgmii(state->interface) && |
| state->interface != PHY_INTERFACE_MODE_INTERNAL) |
| goto unsupported; |
| break; |
| default: |
| bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); |
| dev_err(ds->dev, "Unsupported port: %i\n", port); |
| return; |
| } |
| |
| /* Allow all the expected bits */ |
| phylink_set(mask, Autoneg); |
| phylink_set_port_modes(mask); |
| phylink_set(mask, Pause); |
| phylink_set(mask, Asym_Pause); |
| |
| /* With the exclusion of MII, Reverse MII and Reduced MII, we |
| * support Gigabit, including Half duplex |
| */ |
| if (state->interface != PHY_INTERFACE_MODE_MII && |
| state->interface != PHY_INTERFACE_MODE_REVMII && |
| state->interface != PHY_INTERFACE_MODE_RMII) { |
| phylink_set(mask, 1000baseT_Full); |
| phylink_set(mask, 1000baseT_Half); |
| } |
| |
| phylink_set(mask, 10baseT_Half); |
| phylink_set(mask, 10baseT_Full); |
| phylink_set(mask, 100baseT_Half); |
| phylink_set(mask, 100baseT_Full); |
| |
| bitmap_and(supported, supported, mask, |
| __ETHTOOL_LINK_MODE_MASK_NBITS); |
| bitmap_and(state->advertising, state->advertising, mask, |
| __ETHTOOL_LINK_MODE_MASK_NBITS); |
| return; |
| |
| unsupported: |
| bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); |
| dev_err(ds->dev, "Unsupported interface '%s' for port %d\n", |
| phy_modes(state->interface), port); |
| return; |
| } |
| |
| static void gswip_port_set_link(struct gswip_priv *priv, int port, bool link) |
| { |
| u32 mdio_phy; |
| |
| if (link) |
| mdio_phy = GSWIP_MDIO_PHY_LINK_UP; |
| else |
| mdio_phy = GSWIP_MDIO_PHY_LINK_DOWN; |
| |
| gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_MASK, mdio_phy, |
| GSWIP_MDIO_PHYp(port)); |
| } |
| |
| static void gswip_port_set_speed(struct gswip_priv *priv, int port, int speed, |
| phy_interface_t interface) |
| { |
| u32 mdio_phy = 0, mii_cfg = 0, mac_ctrl_0 = 0; |
| |
| switch (speed) { |
| case SPEED_10: |
| mdio_phy = GSWIP_MDIO_PHY_SPEED_M10; |
| |
| if (interface == PHY_INTERFACE_MODE_RMII) |
| mii_cfg = GSWIP_MII_CFG_RATE_M50; |
| else |
| mii_cfg = GSWIP_MII_CFG_RATE_M2P5; |
| |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; |
| break; |
| |
| case SPEED_100: |
| mdio_phy = GSWIP_MDIO_PHY_SPEED_M100; |
| |
| if (interface == PHY_INTERFACE_MODE_RMII) |
| mii_cfg = GSWIP_MII_CFG_RATE_M50; |
| else |
| mii_cfg = GSWIP_MII_CFG_RATE_M25; |
| |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; |
| break; |
| |
| case SPEED_1000: |
| mdio_phy = GSWIP_MDIO_PHY_SPEED_G1; |
| |
| mii_cfg = GSWIP_MII_CFG_RATE_M125; |
| |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_RGMII; |
| break; |
| } |
| |
| gswip_mdio_mask(priv, GSWIP_MDIO_PHY_SPEED_MASK, mdio_phy, |
| GSWIP_MDIO_PHYp(port)); |
| gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_RATE_MASK, mii_cfg, port); |
| gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_GMII_MASK, mac_ctrl_0, |
| GSWIP_MAC_CTRL_0p(port)); |
| } |
| |
| static void gswip_port_set_duplex(struct gswip_priv *priv, int port, int duplex) |
| { |
| u32 mac_ctrl_0, mdio_phy; |
| |
| if (duplex == DUPLEX_FULL) { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_EN; |
| mdio_phy = GSWIP_MDIO_PHY_FDUP_EN; |
| } else { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_DIS; |
| mdio_phy = GSWIP_MDIO_PHY_FDUP_DIS; |
| } |
| |
| gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FDUP_MASK, mac_ctrl_0, |
| GSWIP_MAC_CTRL_0p(port)); |
| gswip_mdio_mask(priv, GSWIP_MDIO_PHY_FDUP_MASK, mdio_phy, |
| GSWIP_MDIO_PHYp(port)); |
| } |
| |
| static void gswip_port_set_pause(struct gswip_priv *priv, int port, |
| bool tx_pause, bool rx_pause) |
| { |
| u32 mac_ctrl_0, mdio_phy; |
| |
| if (tx_pause && rx_pause) { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RXTX; |
| mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | |
| GSWIP_MDIO_PHY_FCONRX_EN; |
| } else if (tx_pause) { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_TX; |
| mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | |
| GSWIP_MDIO_PHY_FCONRX_DIS; |
| } else if (rx_pause) { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RX; |
| mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | |
| GSWIP_MDIO_PHY_FCONRX_EN; |
| } else { |
| mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_NONE; |
| mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | |
| GSWIP_MDIO_PHY_FCONRX_DIS; |
| } |
| |
| gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FCON_MASK, |
| mac_ctrl_0, GSWIP_MAC_CTRL_0p(port)); |
| gswip_mdio_mask(priv, |
| GSWIP_MDIO_PHY_FCONTX_MASK | |
| GSWIP_MDIO_PHY_FCONRX_MASK, |
| mdio_phy, GSWIP_MDIO_PHYp(port)); |
| } |
| |
| static void gswip_phylink_mac_config(struct dsa_switch *ds, int port, |
| unsigned int mode, |
| const struct phylink_link_state *state) |
| { |
| struct gswip_priv *priv = ds->priv; |
| u32 miicfg = 0; |
| |
| miicfg |= GSWIP_MII_CFG_LDCLKDIS; |
| |
| switch (state->interface) { |
| case PHY_INTERFACE_MODE_MII: |
| case PHY_INTERFACE_MODE_INTERNAL: |
| miicfg |= GSWIP_MII_CFG_MODE_MIIM; |
| break; |
| case PHY_INTERFACE_MODE_REVMII: |
| miicfg |= GSWIP_MII_CFG_MODE_MIIP; |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| miicfg |= GSWIP_MII_CFG_MODE_RMIIM; |
| |
| /* Configure the RMII clock as output: */ |
| miicfg |= GSWIP_MII_CFG_RMII_CLK; |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| miicfg |= GSWIP_MII_CFG_MODE_RGMII; |
| break; |
| default: |
| dev_err(ds->dev, |
| "Unsupported interface: %d\n", state->interface); |
| return; |
| } |
| |
| gswip_mii_mask_cfg(priv, |
| GSWIP_MII_CFG_MODE_MASK | GSWIP_MII_CFG_RMII_CLK | |
| GSWIP_MII_CFG_RGMII_IBS | GSWIP_MII_CFG_LDCLKDIS, |
| miicfg, port); |
| |
| switch (state->interface) { |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK | |
| GSWIP_MII_PCDU_RXDLY_MASK, 0, port); |
| break; |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port); |
| break; |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port, |
| unsigned int mode, |
| phy_interface_t interface) |
| { |
| struct gswip_priv *priv = ds->priv; |
| |
| gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port); |
| |
| if (!dsa_is_cpu_port(ds, port)) |
| gswip_port_set_link(priv, port, false); |
| } |
| |
| static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port, |
| unsigned int mode, |
| phy_interface_t interface, |
| struct phy_device *phydev, |
| int speed, int duplex, |
| bool tx_pause, bool rx_pause) |
| { |
| struct gswip_priv *priv = ds->priv; |
| |
| if (!dsa_is_cpu_port(ds, port)) { |
| gswip_port_set_link(priv, port, true); |
| gswip_port_set_speed(priv, port, speed, interface); |
| gswip_port_set_duplex(priv, port, duplex); |
| gswip_port_set_pause(priv, port, tx_pause, rx_pause); |
| } |
| |
| gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port); |
| } |
| |
| static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset, |
| uint8_t *data) |
| { |
| int i; |
| |
| if (stringset != ETH_SS_STATS) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) |
| strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name, |
| ETH_GSTRING_LEN); |
| } |
| |
| static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table, |
| u32 index) |
| { |
| u32 result; |
| int err; |
| |
| gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR); |
| gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK | |
| GSWIP_BM_RAM_CTRL_OPMOD, |
| table | GSWIP_BM_RAM_CTRL_BAS, |
| GSWIP_BM_RAM_CTRL); |
| |
| err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL, |
| GSWIP_BM_RAM_CTRL_BAS); |
| if (err) { |
| dev_err(priv->dev, "timeout while reading table: %u, index: %u", |
| table, index); |
| return 0; |
| } |
| |
| result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0)); |
| result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16; |
| |
| return result; |
| } |
| |
| static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port, |
| uint64_t *data) |
| { |
| struct gswip_priv *priv = ds->priv; |
| const struct gswip_rmon_cnt_desc *rmon_cnt; |
| int i; |
| u64 high; |
| |
| for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) { |
| rmon_cnt = &gswip_rmon_cnt[i]; |
| |
| data[i] = gswip_bcm_ram_entry_read(priv, port, |
| rmon_cnt->offset); |
| if (rmon_cnt->size == 2) { |
| high = gswip_bcm_ram_entry_read(priv, port, |
| rmon_cnt->offset + 1); |
| data[i] |= high << 32; |
| } |
| } |
| } |
| |
| static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset) |
| { |
| if (sset != ETH_SS_STATS) |
| return 0; |
| |
| return ARRAY_SIZE(gswip_rmon_cnt); |
| } |
| |
| static const struct dsa_switch_ops gswip_switch_ops = { |
| .get_tag_protocol = gswip_get_tag_protocol, |
| .setup = gswip_setup, |
| .port_enable = gswip_port_enable, |
| .port_disable = gswip_port_disable, |
| .port_bridge_join = gswip_port_bridge_join, |
| .port_bridge_leave = gswip_port_bridge_leave, |
| .port_fast_age = gswip_port_fast_age, |
| .port_vlan_filtering = gswip_port_vlan_filtering, |
| .port_vlan_prepare = gswip_port_vlan_prepare, |
| .port_vlan_add = gswip_port_vlan_add, |
| .port_vlan_del = gswip_port_vlan_del, |
| .port_stp_state_set = gswip_port_stp_state_set, |
| .port_fdb_add = gswip_port_fdb_add, |
| .port_fdb_del = gswip_port_fdb_del, |
| .port_fdb_dump = gswip_port_fdb_dump, |
| .phylink_validate = gswip_phylink_validate, |
| .phylink_mac_config = gswip_phylink_mac_config, |
| .phylink_mac_link_down = gswip_phylink_mac_link_down, |
| .phylink_mac_link_up = gswip_phylink_mac_link_up, |
| .get_strings = gswip_get_strings, |
| .get_ethtool_stats = gswip_get_ethtool_stats, |
| .get_sset_count = gswip_get_sset_count, |
| }; |
| |
| static const struct xway_gphy_match_data xrx200a1x_gphy_data = { |
| .fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin", |
| .ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin", |
| }; |
| |
| static const struct xway_gphy_match_data xrx200a2x_gphy_data = { |
| .fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin", |
| .ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin", |
| }; |
| |
| static const struct xway_gphy_match_data xrx300_gphy_data = { |
| .fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin", |
| .ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin", |
| }; |
| |
| static const struct of_device_id xway_gphy_match[] = { |
| { .compatible = "lantiq,xrx200-gphy-fw", .data = NULL }, |
| { .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data }, |
| { .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data }, |
| { .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data }, |
| { .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data }, |
| {}, |
| }; |
| |
| static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw) |
| { |
| struct device *dev = priv->dev; |
| const struct firmware *fw; |
| void *fw_addr; |
| dma_addr_t dma_addr; |
| dma_addr_t dev_addr; |
| size_t size; |
| int ret; |
| |
| ret = clk_prepare_enable(gphy_fw->clk_gate); |
| if (ret) |
| return ret; |
| |
| reset_control_assert(gphy_fw->reset); |
| |
| ret = request_firmware(&fw, gphy_fw->fw_name, dev); |
| if (ret) { |
| dev_err(dev, "failed to load firmware: %s, error: %i\n", |
| gphy_fw->fw_name, ret); |
| return ret; |
| } |
| |
| /* GPHY cores need the firmware code in a persistent and contiguous |
| * memory area with a 16 kB boundary aligned start address. |
| */ |
| size = fw->size + XRX200_GPHY_FW_ALIGN; |
| |
| fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL); |
| if (fw_addr) { |
| fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN); |
| dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN); |
| memcpy(fw_addr, fw->data, fw->size); |
| } else { |
| dev_err(dev, "failed to alloc firmware memory\n"); |
| release_firmware(fw); |
| return -ENOMEM; |
| } |
| |
| release_firmware(fw); |
| |
| ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr); |
| if (ret) |
| return ret; |
| |
| reset_control_deassert(gphy_fw->reset); |
| |
| return ret; |
| } |
| |
| static int gswip_gphy_fw_probe(struct gswip_priv *priv, |
| struct gswip_gphy_fw *gphy_fw, |
| struct device_node *gphy_fw_np, int i) |
| { |
| struct device *dev = priv->dev; |
| u32 gphy_mode; |
| int ret; |
| char gphyname[10]; |
| |
| snprintf(gphyname, sizeof(gphyname), "gphy%d", i); |
| |
| gphy_fw->clk_gate = devm_clk_get(dev, gphyname); |
| if (IS_ERR(gphy_fw->clk_gate)) { |
| dev_err(dev, "Failed to lookup gate clock\n"); |
| return PTR_ERR(gphy_fw->clk_gate); |
| } |
| |
| ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset); |
| if (ret) |
| return ret; |
| |
| ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode); |
| /* Default to GE mode */ |
| if (ret) |
| gphy_mode = GPHY_MODE_GE; |
| |
| switch (gphy_mode) { |
| case GPHY_MODE_FE: |
| gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name; |
| break; |
| case GPHY_MODE_GE: |
| gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name; |
| break; |
| default: |
| dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode); |
| return -EINVAL; |
| } |
| |
| gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np); |
| if (IS_ERR(gphy_fw->reset)) { |
| if (PTR_ERR(gphy_fw->reset) != -EPROBE_DEFER) |
| dev_err(dev, "Failed to lookup gphy reset\n"); |
| return PTR_ERR(gphy_fw->reset); |
| } |
| |
| return gswip_gphy_fw_load(priv, gphy_fw); |
| } |
| |
| static void gswip_gphy_fw_remove(struct gswip_priv *priv, |
| struct gswip_gphy_fw *gphy_fw) |
| { |
| int ret; |
| |
| /* check if the device was fully probed */ |
| if (!gphy_fw->fw_name) |
| return; |
| |
| ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0); |
| if (ret) |
| dev_err(priv->dev, "can not reset GPHY FW pointer"); |
| |
| clk_disable_unprepare(gphy_fw->clk_gate); |
| |
| reset_control_put(gphy_fw->reset); |
| } |
| |
| static int gswip_gphy_fw_list(struct gswip_priv *priv, |
| struct device_node *gphy_fw_list_np, u32 version) |
| { |
| struct device *dev = priv->dev; |
| struct device_node *gphy_fw_np; |
| const struct of_device_id *match; |
| int err; |
| int i = 0; |
| |
| /* The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older |
| * GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also |
| * needs a different GPHY firmware. |
| */ |
| if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) { |
| switch (version) { |
| case GSWIP_VERSION_2_0: |
| priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data; |
| break; |
| case GSWIP_VERSION_2_1: |
| priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data; |
| break; |
| default: |
| dev_err(dev, "unknown GSWIP version: 0x%x", version); |
| return -ENOENT; |
| } |
| } |
| |
| match = of_match_node(xway_gphy_match, gphy_fw_list_np); |
| if (match && match->data) |
| priv->gphy_fw_name_cfg = match->data; |
| |
| if (!priv->gphy_fw_name_cfg) { |
| dev_err(dev, "GPHY compatible type not supported"); |
| return -ENOENT; |
| } |
| |
| priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np); |
| if (!priv->num_gphy_fw) |
| return -ENOENT; |
| |
| priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np, |
| "lantiq,rcu"); |
| if (IS_ERR(priv->rcu_regmap)) |
| return PTR_ERR(priv->rcu_regmap); |
| |
| priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw, |
| sizeof(*priv->gphy_fw), |
| GFP_KERNEL | __GFP_ZERO); |
| if (!priv->gphy_fw) |
| return -ENOMEM; |
| |
| for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) { |
| err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i], |
| gphy_fw_np, i); |
| if (err) |
| goto remove_gphy; |
| i++; |
| } |
| |
| /* The standalone PHY11G requires 300ms to be fully |
| * initialized and ready for any MDIO communication after being |
| * taken out of reset. For the SoC-internal GPHY variant there |
| * is no (known) documentation for the minimum time after a |
| * reset. Use the same value as for the standalone variant as |
| * some users have reported internal PHYs not being detected |
| * without any delay. |
| */ |
| msleep(300); |
| |
| return 0; |
| |
| remove_gphy: |
| for (i = 0; i < priv->num_gphy_fw; i++) |
| gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); |
| return err; |
| } |
| |
| static int gswip_probe(struct platform_device *pdev) |
| { |
| struct gswip_priv *priv; |
| struct device_node *mdio_np, *gphy_fw_np; |
| struct device *dev = &pdev->dev; |
| int err; |
| int i; |
| u32 version; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->gswip = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(priv->gswip)) |
| return PTR_ERR(priv->gswip); |
| |
| priv->mdio = devm_platform_ioremap_resource(pdev, 1); |
| if (IS_ERR(priv->mdio)) |
| return PTR_ERR(priv->mdio); |
| |
| priv->mii = devm_platform_ioremap_resource(pdev, 2); |
| if (IS_ERR(priv->mii)) |
| return PTR_ERR(priv->mii); |
| |
| priv->hw_info = of_device_get_match_data(dev); |
| if (!priv->hw_info) |
| return -EINVAL; |
| |
| priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL); |
| if (!priv->ds) |
| return -ENOMEM; |
| |
| priv->ds->dev = dev; |
| priv->ds->num_ports = priv->hw_info->max_ports; |
| priv->ds->priv = priv; |
| priv->ds->ops = &gswip_switch_ops; |
| priv->dev = dev; |
| version = gswip_switch_r(priv, GSWIP_VERSION); |
| |
| /* bring up the mdio bus */ |
| gphy_fw_np = of_get_compatible_child(dev->of_node, "lantiq,gphy-fw"); |
| if (gphy_fw_np) { |
| err = gswip_gphy_fw_list(priv, gphy_fw_np, version); |
| of_node_put(gphy_fw_np); |
| if (err) { |
| dev_err(dev, "gphy fw probe failed\n"); |
| return err; |
| } |
| } |
| |
| /* bring up the mdio bus */ |
| mdio_np = of_get_compatible_child(dev->of_node, "lantiq,xrx200-mdio"); |
| if (mdio_np) { |
| err = gswip_mdio(priv, mdio_np); |
| if (err) { |
| dev_err(dev, "mdio probe failed\n"); |
| goto put_mdio_node; |
| } |
| } |
| |
| err = dsa_register_switch(priv->ds); |
| if (err) { |
| dev_err(dev, "dsa switch register failed: %i\n", err); |
| goto mdio_bus; |
| } |
| if (!dsa_is_cpu_port(priv->ds, priv->hw_info->cpu_port)) { |
| dev_err(dev, "wrong CPU port defined, HW only supports port: %i", |
| priv->hw_info->cpu_port); |
| err = -EINVAL; |
| goto disable_switch; |
| } |
| |
| platform_set_drvdata(pdev, priv); |
| |
| dev_info(dev, "probed GSWIP version %lx mod %lx\n", |
| (version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT, |
| (version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT); |
| return 0; |
| |
| disable_switch: |
| gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); |
| dsa_unregister_switch(priv->ds); |
| mdio_bus: |
| if (mdio_np) { |
| mdiobus_unregister(priv->ds->slave_mii_bus); |
| mdiobus_free(priv->ds->slave_mii_bus); |
| } |
| put_mdio_node: |
| of_node_put(mdio_np); |
| for (i = 0; i < priv->num_gphy_fw; i++) |
| gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); |
| return err; |
| } |
| |
| static int gswip_remove(struct platform_device *pdev) |
| { |
| struct gswip_priv *priv = platform_get_drvdata(pdev); |
| int i; |
| |
| /* disable the switch */ |
| gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); |
| |
| dsa_unregister_switch(priv->ds); |
| |
| if (priv->ds->slave_mii_bus) { |
| mdiobus_unregister(priv->ds->slave_mii_bus); |
| of_node_put(priv->ds->slave_mii_bus->dev.of_node); |
| mdiobus_free(priv->ds->slave_mii_bus); |
| } |
| |
| for (i = 0; i < priv->num_gphy_fw; i++) |
| gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); |
| |
| return 0; |
| } |
| |
| static const struct gswip_hw_info gswip_xrx200 = { |
| .max_ports = 7, |
| .cpu_port = 6, |
| }; |
| |
| static const struct of_device_id gswip_of_match[] = { |
| { .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, gswip_of_match); |
| |
| static struct platform_driver gswip_driver = { |
| .probe = gswip_probe, |
| .remove = gswip_remove, |
| .driver = { |
| .name = "gswip", |
| .of_match_table = gswip_of_match, |
| }, |
| }; |
| |
| module_platform_driver(gswip_driver); |
| |
| MODULE_FIRMWARE("lantiq/xrx300_phy11g_a21.bin"); |
| MODULE_FIRMWARE("lantiq/xrx300_phy22f_a21.bin"); |
| MODULE_FIRMWARE("lantiq/xrx200_phy11g_a14.bin"); |
| MODULE_FIRMWARE("lantiq/xrx200_phy11g_a22.bin"); |
| MODULE_FIRMWARE("lantiq/xrx200_phy22f_a14.bin"); |
| MODULE_FIRMWARE("lantiq/xrx200_phy22f_a22.bin"); |
| MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>"); |
| MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver"); |
| MODULE_LICENSE("GPL v2"); |