ata: ahci: Skip 200 ms debounce delay for Marvell 88SE9235
The 200 ms delay before debouncing the PHY in `sata_link_resume()` is
not needed for the Marvell 88SE9235.
$ lspci -nn -s 0021:0e:00.0
0021:0e:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9235 PCIe 2.0 x2 4-port SATA 6 Gb/s Controller [1b4b:9235] (rev 11)
So, remove it using the board_ahci_no_debounce_delay board definition.
Tested on IBM S822LC with current Linux 5.17-rc1:
Currently, without this patch (with 200 ms delay), device probe for ata1
takes 485 ms:
[ 3.358158] ata1: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000100 irq 39
[ 3.358175] ata2: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000180 irq 39
[ 3.358191] ata3: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000200 irq 39
[ 3.358207] ata4: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3fe881000280 irq 39
[…]
[ 3.677542] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.677719] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.839242] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.839828] ata2.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.840029] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.841796] ata2.00: configured for UDMA/133
[ 3.843231] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.844083] ata1.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.844313] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.846043] ata1.00: configured for UDMA/133
With this patch (no delay) device probe for ata1 takes 273 ms:
[ 3.624259] ata1: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000100 irq 39
[ 3.624436] ata2: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000180 irq 39
[ 3.624452] ata3: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000200 irq 39
[ 3.624468] ata4: SATA max UDMA/133 abar m2048@0x3fe881000000 port 0x3f e881000280 irq 39
[…]
[ 3.731966] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.732069] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.897448] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.897678] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.898140] ata1.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.898175] ata2.00: ATA-10: ST1000NX0313 00LY266 00LY265IBM, BE33, max UDMA/133
[ 3.898287] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.898349] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.900070] ata1.00: configured for UDMA/133
[ 3.900166] ata2.00: configured for UDMA/133
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
1 file changed
