// SPDX-License-Identifier: GPL-2.0
/dts-v1/;

#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,msm8974.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/reset/qcom,gcc-msm8974.h>

/ {
	#address-cells = <1>;
	#size-cells = <1>;
	interrupt-parent = <&intc>;

	chosen { };

	clocks {
		xo_board: xo_board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <19200000>;
		};

		sleep_clk: sleep_clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32768>;
		};
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;
		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;

		cpu0: cpu@0 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v2";
			device_type = "cpu";
			reg = <0>;
			next-level-cache = <&l2>;
			qcom,acc = <&acc0>;
			qcom,saw = <&saw0>;
			cpu-idle-states = <&cpu_spc>;
		};

		cpu1: cpu@1 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v2";
			device_type = "cpu";
			reg = <1>;
			next-level-cache = <&l2>;
			qcom,acc = <&acc1>;
			qcom,saw = <&saw1>;
			cpu-idle-states = <&cpu_spc>;
		};

		cpu2: cpu@2 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v2";
			device_type = "cpu";
			reg = <2>;
			next-level-cache = <&l2>;
			qcom,acc = <&acc2>;
			qcom,saw = <&saw2>;
			cpu-idle-states = <&cpu_spc>;
		};

		cpu3: cpu@3 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v2";
			device_type = "cpu";
			reg = <3>;
			next-level-cache = <&l2>;
			qcom,acc = <&acc3>;
			qcom,saw = <&saw3>;
			cpu-idle-states = <&cpu_spc>;
		};

		l2: l2-cache {
			compatible = "cache";
			cache-level = <2>;
			cache-unified;
			qcom,saw = <&saw_l2>;
		};

		idle-states {
			cpu_spc: cpu-spc {
				compatible = "qcom,idle-state-spc",
						"arm,idle-state";
				entry-latency-us = <150>;
				exit-latency-us = <200>;
				min-residency-us = <2000>;
			};
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-msm8974", "qcom,scm";
			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
			clock-names = "core", "bus", "iface";
		};
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x0>;
	};

	pmu {
		compatible = "qcom,krait-pmu";
		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
	};

	rpm: remoteproc {
		compatible = "qcom,msm8974-rpm-proc", "qcom,rpm-proc";

		master-stats {
			compatible = "qcom,rpm-master-stats";
			qcom,rpm-msg-ram = <&apss_master_stats>,
					   <&mpss_master_stats>,
					   <&lpss_master_stats>,
					   <&pronto_master_stats>;
			qcom,master-names = "APSS",
					    "MPSS",
					    "LPSS",
					    "PRONTO";
		};

		smd-edge {
			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
			mboxes = <&apcs 0>;
			qcom,smd-edge = <15>;

			rpm_requests: rpm-requests {
				compatible = "qcom,rpm-msm8974", "qcom,smd-rpm";
				qcom,smd-channels = "rpm_requests";

				rpmcc: clock-controller {
					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
					#clock-cells = <1>;
					clocks = <&xo_board>;
					clock-names = "xo";
				};

				rpmpd: power-controller {
					compatible = "qcom,msm8974-rpmpd";
					#power-domain-cells = <1>;
					operating-points-v2 = <&rpmpd_opp_table>;

					rpmpd_opp_table: opp-table {
						compatible = "operating-points-v2";

						rpmpd_opp_ret: opp1 {
							opp-level = <1>;
						};

						rpmpd_opp_svs_krait: opp2 {
							opp-level = <2>;
						};

						rpmpd_opp_svs_soc: opp3 {
							opp-level = <3>;
						};

						rpmpd_opp_nom: opp4 {
							opp-level = <4>;
						};

						rpmpd_opp_turbo: opp5 {
							opp-level = <5>;
						};

						rpmpd_opp_super_turbo: opp6 {
							opp-level = <6>;
						};
					};
				};
			};
		};
	};

	reserved_memory: reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		mpss_region: mpss@8000000 {
			reg = <0x08000000 0x5100000>;
			no-map;
		};

		mba_region: mba@d100000 {
			reg = <0x0d100000 0x100000>;
			no-map;
		};

		wcnss_region: wcnss@d200000 {
			reg = <0x0d200000 0xa00000>;
			no-map;
		};

		adsp_region: adsp@dc00000 {
			reg = <0x0dc00000 0x1900000>;
			no-map;
		};

		venus_region: memory@f500000 {
			reg = <0x0f500000 0x500000>;
			no-map;
		};

		smem_region: smem@fa00000 {
			reg = <0xfa00000 0x200000>;
			no-map;
		};

		tz_region: memory@fc00000 {
			reg = <0x0fc00000 0x160000>;
			no-map;
		};

		rfsa_mem: memory@fd60000 {
			reg = <0x0fd60000 0x20000>;
			no-map;
		};

		rmtfs@fd80000 {
			compatible = "qcom,rmtfs-mem";
			reg = <0x0fd80000 0x180000>;
			no-map;

			qcom,client-id = <1>;
		};
	};

	smem {
		compatible = "qcom,smem";

		memory-region = <&smem_region>;
		qcom,rpm-msg-ram = <&rpm_msg_ram>;

		hwlocks = <&tcsr_mutex 3>;
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;

		interrupt-parent = <&intc>;
		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs 10>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		adsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		adsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-modem {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;

		interrupt-parent = <&intc>;
		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs 14>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		modem_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		modem_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-wcnss {
		compatible = "qcom,smp2p";
		qcom,smem = <451>, <431>;

		interrupt-parent = <&intc>;
		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs 18>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <4>;

		wcnss_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";

			#qcom,smem-state-cells = <1>;
		};

		wcnss_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smsm {
		compatible = "qcom,smsm";

		#address-cells = <1>;
		#size-cells = <0>;

		mboxes = <0>, <&apcs 13>, <&apcs 9>, <&apcs 19>;

		apps_smsm: apps@0 {
			reg = <0>;

			#qcom,smem-state-cells = <1>;
		};

		modem_smsm: modem@1 {
			reg = <1>;
			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		adsp_smsm: adsp@2 {
			reg = <2>;
			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		wcnss_smsm: wcnss@7 {
			reg = <7>;
			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		compatible = "simple-bus";

		intc: interrupt-controller@f9000000 {
			compatible = "qcom,msm-qgic2";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0xf9000000 0x1000>,
			      <0xf9002000 0x1000>;
		};

		apcs: mailbox@f9011000 {
			compatible = "qcom,msm8974-apcs-kpss-global",
				     "qcom,msm8994-apcs-kpss-global", "syscon";
			reg = <0xf9011000 0x1000>;
			#mbox-cells = <1>;
		};

		saw_l2: power-manager@f9012000 {
			compatible = "qcom,msm8974-saw2-v2.1-l2", "qcom,saw2";
			reg = <0xf9012000 0x1000>;
		};

		watchdog@f9017000 {
			compatible = "qcom,apss-wdt-msm8974", "qcom,kpss-wdt";
			reg = <0xf9017000 0x1000>;
			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
			clocks = <&sleep_clk>;
		};

		timer@f9020000 {
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			compatible = "arm,armv7-timer-mem";
			reg = <0xf9020000 0x1000>;
			clock-frequency = <19200000>;

			frame@f9021000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9021000 0x1000>,
				      <0xf9022000 0x1000>;
			};

			frame@f9023000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9023000 0x1000>;
				status = "disabled";
			};

			frame@f9024000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9024000 0x1000>;
				status = "disabled";
			};

			frame@f9025000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9025000 0x1000>;
				status = "disabled";
			};

			frame@f9026000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9026000 0x1000>;
				status = "disabled";
			};

			frame@f9027000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9027000 0x1000>;
				status = "disabled";
			};

			frame@f9028000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0xf9028000 0x1000>;
				status = "disabled";
			};
		};

		acc0: power-manager@f9088000 {
			compatible = "qcom,kpss-acc-v2";
			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
		};

		saw0: power-manager@f9089000 {
			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
		};

		acc1: power-manager@f9098000 {
			compatible = "qcom,kpss-acc-v2";
			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
		};

		saw1: power-manager@f9099000 {
			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
		};

		acc2: power-manager@f90a8000 {
			compatible = "qcom,kpss-acc-v2";
			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
		};

		saw2: power-manager@f90a9000 {
			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
		};

		acc3: power-manager@f90b8000 {
			compatible = "qcom,kpss-acc-v2";
			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
		};

		saw3: power-manager@f90b9000 {
			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
		};

		sdhc_1: mmc@f9824900 {
			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
			reg-names = "hc", "core";
			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";
			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
				 <&gcc GCC_SDCC1_APPS_CLK>,
				 <&xo_board>;
			clock-names = "iface", "core", "xo";
			bus-width = <8>;
			non-removable;

			status = "disabled";
		};

		sdhc_3: mmc@f9864900 {
			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
			reg-names = "hc", "core";
			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";
			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
				 <&gcc GCC_SDCC3_APPS_CLK>,
				 <&xo_board>;
			clock-names = "iface", "core", "xo";
			bus-width = <4>;

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";
		};

		sdhc_2: mmc@f98a4900 {
			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
			reg-names = "hc", "core";
			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";
			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&xo_board>;
			clock-names = "iface", "core", "xo";
			bus-width = <4>;

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";
		};

		blsp1_uart1: serial@f991d000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0xf991d000 0x1000>;
			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp1_uart2: serial@f991e000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0xf991e000 0x1000>;
			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default";
			pinctrl-0 = <&blsp1_uart2_default>;
			status = "disabled";
		};

		blsp1_i2c1: i2c@f9923000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9923000 0x1000>;
			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c1_default>;
			pinctrl-1 = <&blsp1_i2c1_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp1_i2c2: i2c@f9924000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9924000 0x1000>;
			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c2_default>;
			pinctrl-1 = <&blsp1_i2c2_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp1_i2c3: i2c@f9925000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9925000 0x1000>;
			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c3_default>;
			pinctrl-1 = <&blsp1_i2c3_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp1_i2c6: i2c@f9928000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9928000 0x1000>;
			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c6_default>;
			pinctrl-1 = <&blsp1_i2c6_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp2_dma: dma-controller@f9944000 {
			compatible = "qcom,bam-v1.4.0";
			reg = <0xf9944000 0x19000>;
			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		blsp2_uart1: serial@f995d000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0xf995d000 0x1000>;
			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_uart1_default>;
			pinctrl-1 = <&blsp2_uart1_sleep>;
			status = "disabled";
		};

		blsp2_uart2: serial@f995e000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0xf995e000 0x1000>;
			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp2_uart4: serial@f9960000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0xf9960000 0x1000>;
			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_UART4_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default";
			pinctrl-0 = <&blsp2_uart4_default>;
			status = "disabled";
		};

		blsp2_i2c2: i2c@f9964000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9964000 0x1000>;
			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c2_default>;
			pinctrl-1 = <&blsp2_i2c2_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp2_i2c5: i2c@f9967000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9967000 0x1000>;
			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
			dma-names = "tx", "rx";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c5_default>;
			pinctrl-1 = <&blsp2_i2c5_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		blsp2_i2c6: i2c@f9968000 {
			status = "disabled";
			compatible = "qcom,i2c-qup-v2.1.1";
			reg = <0xf9968000 0x1000>;
			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c6_default>;
			pinctrl-1 = <&blsp2_i2c6_sleep>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		usb: usb@f9a55000 {
			compatible = "qcom,ci-hdrc";
			reg = <0xf9a55000 0x200>,
			      <0xf9a55200 0x200>;
			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
			clock-names = "iface", "core";
			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
			assigned-clock-rates = <75000000>;
			resets = <&gcc GCC_USB_HS_BCR>;
			reset-names = "core";
			phy_type = "ulpi";
			dr_mode = "otg";
			ahb-burst-config = <0>;
			phy-names = "usb-phy";
			status = "disabled";
			#reset-cells = <1>;

			ulpi {
				usb_hs1_phy: phy-0 {
					compatible = "qcom,usb-hs-phy-msm8974",
						     "qcom,usb-hs-phy";
					#phy-cells = <0>;
					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
					clock-names = "ref", "sleep";
					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
					reset-names = "phy", "por";
					status = "disabled";
				};

				usb_hs2_phy: phy-1 {
					compatible = "qcom,usb-hs-phy-msm8974",
						     "qcom,usb-hs-phy";
					#phy-cells = <0>;
					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
					clock-names = "ref", "sleep";
					resets = <&gcc GCC_USB2B_PHY_BCR>, <&usb 1>;
					reset-names = "phy", "por";
					status = "disabled";
				};
			};
		};

		rng@f9bff000 {
			compatible = "qcom,prng";
			reg = <0xf9bff000 0x200>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
		};

		pronto: remoteproc@fb204000 {
			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
			reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
			reg-names = "ccu", "dxe", "pmu";

			memory-region = <&wcnss_region>;

			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";

			power-domains = <&rpmpd MSM8974_VDDCX>;
			power-domain-names = "cx";

			qcom,smem-states = <&wcnss_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			iris {
				compatible = "qcom,wcn3680";

				clocks = <&rpmcc RPM_SMD_CXO_A2>;
				clock-names = "xo";
			};

			smd-edge {
				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;

				mboxes = <&apcs 17>;
				qcom,smd-edge = <6>;

				wcnss {
					compatible = "qcom,wcnss";
					qcom,smd-channels = "WCNSS_CTRL";
					status = "disabled";

					qcom,mmio = <&pronto>;

					bluetooth {
						compatible = "qcom,wcnss-bt";
					};

					wifi {
						compatible = "qcom,wcnss-wlan";

						interrupts = <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>,
							     <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>;
						interrupt-names = "tx", "rx";

						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
						qcom,smem-state-names = "tx-enable",
									"tx-rings-empty";
					};
				};
			};
		};

		sram@fc190000 {
			compatible = "qcom,msm8974-rpm-stats";
			reg = <0xfc190000 0x10000>;
		};

		etf@fc307000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0xfc307000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			out-ports {
				port {
					etf_out: endpoint {
						remote-endpoint = <&replicator_in>;
					};
				};
			};

			in-ports {
				port {
					etf_in: endpoint {
						remote-endpoint = <&merger_out>;
					};
				};
			};
		};

		tpiu@fc318000 {
			compatible = "arm,coresight-tpiu", "arm,primecell";
			reg = <0xfc318000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					tpiu_in: endpoint {
						remote-endpoint = <&replicator_out1>;
					};
				 };
			};
		};

		funnel@fc31a000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0xfc31a000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				/*
				 * Not described input ports:
				 * 0 - not-connected
				 * 1 - connected trought funnel to Multimedia CPU
				 * 2 - connected to Wireless CPU
				 * 3 - not-connected
				 * 4 - not-connected
				 * 6 - not-connected
				 * 7 - connected to STM
				 */
				port@5 {
					reg = <5>;
					funnel1_in5: endpoint {
						remote-endpoint = <&kpss_out>;
					};
				};
			};

			out-ports {
				port {
					funnel1_out: endpoint {
						remote-endpoint = <&merger_in1>;
					};
				};
			};
		};

		funnel@fc31b000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0xfc31b000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				/*
				 * Not described input ports:
				 * 0 - connected trought funnel to Audio, Modem and
				 *     Resource and Power Manager CPU's
				 * 2...7 - not-connected
				 */
				port@1 {
					reg = <1>;
					merger_in1: endpoint {
						remote-endpoint = <&funnel1_out>;
					};
				};
			};

			out-ports {
				port {
					merger_out: endpoint {
						remote-endpoint = <&etf_in>;
					};
				};
			};
		};

		replicator@fc31c000 {
			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
			reg = <0xfc31c000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			out-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					replicator_out0: endpoint {
						remote-endpoint = <&etr_in>;
					};
				};
				port@1 {
					reg = <1>;
					replicator_out1: endpoint {
						remote-endpoint = <&tpiu_in>;
					};
				};
			};

			in-ports {
				port {
					replicator_in: endpoint {
						remote-endpoint = <&etf_out>;
					};
				};
			};
		};

		etr@fc322000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0xfc322000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					etr_in: endpoint {
						remote-endpoint = <&replicator_out0>;
					};
				};
			};
		};

		etm@fc33c000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0xfc33c000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&cpu0>;

			out-ports {
				port {
					etm0_out: endpoint {
						remote-endpoint = <&kpss_in0>;
					};
				};
			};
		};

		etm@fc33d000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0xfc33d000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&cpu1>;

			out-ports {
				port {
					etm1_out: endpoint {
						remote-endpoint = <&kpss_in1>;
					};
				};
			};
		};

		etm@fc33e000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0xfc33e000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&cpu2>;

			out-ports {
				port {
					etm2_out: endpoint {
						remote-endpoint = <&kpss_in2>;
					};
				};
			};
		};

		etm@fc33f000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0xfc33f000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&cpu3>;

			out-ports {
				port {
					etm3_out: endpoint {
						remote-endpoint = <&kpss_in3>;
					};
				};
			};
		};

		/* KPSS funnel, only 4 inputs are used */
		funnel@fc345000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0xfc345000 0x1000>;

			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					kpss_in0: endpoint {
						remote-endpoint = <&etm0_out>;
					};
				};
				port@1 {
					reg = <1>;
					kpss_in1: endpoint {
						remote-endpoint = <&etm1_out>;
					};
				};
				port@2 {
					reg = <2>;
					kpss_in2: endpoint {
						remote-endpoint = <&etm2_out>;
					};
				};
				port@3 {
					reg = <3>;
					kpss_in3: endpoint {
						remote-endpoint = <&etm3_out>;
					};
				};
			};

			out-ports {
				port {
					kpss_out: endpoint {
						remote-endpoint = <&funnel1_in5>;
					};
				};
			};
		};

		bimc: interconnect@fc380000 {
			reg = <0xfc380000 0x6a000>;
			compatible = "qcom,msm8974-bimc";
			#interconnect-cells = <1>;
		};

		gcc: clock-controller@fc400000 {
			compatible = "qcom,gcc-msm8974";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			reg = <0xfc400000 0x4000>;

			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
				 <&sleep_clk>;
			clock-names = "xo",
				      "sleep_clk";
		};

		rpm_msg_ram: sram@fc428000 {
			compatible = "qcom,rpm-msg-ram";
			reg = <0xfc428000 0x4000>;

			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0xfc428000 0x4000>;

			apss_master_stats: sram@150 {
				reg = <0x150 0x14>;
			};

			mpss_master_stats: sram@b50 {
				reg = <0xb50 0x14>;
			};

			lpss_master_stats: sram@1550 {
				reg = <0x1550 0x14>;
			};

			pronto_master_stats: sram@1f50 {
				reg = <0x1f50 0x14>;
			};
		};

		snoc: interconnect@fc460000 {
			reg = <0xfc460000 0x4000>;
			compatible = "qcom,msm8974-snoc";
			#interconnect-cells = <1>;
		};

		pnoc: interconnect@fc468000 {
			reg = <0xfc468000 0x4000>;
			compatible = "qcom,msm8974-pnoc";
			#interconnect-cells = <1>;
		};

		ocmemnoc: interconnect@fc470000 {
			reg = <0xfc470000 0x4000>;
			compatible = "qcom,msm8974-ocmemnoc";
			#interconnect-cells = <1>;
		};

		mmssnoc: interconnect@fc478000 {
			reg = <0xfc478000 0x4000>;
			compatible = "qcom,msm8974-mmssnoc";
			#interconnect-cells = <1>;
			clocks = <&mmcc MMSS_S0_AXI_CLK>;
			clock-names = "bus";
		};

		cnoc: interconnect@fc480000 {
			reg = <0xfc480000 0x4000>;
			compatible = "qcom,msm8974-cnoc";
			#interconnect-cells = <1>;
		};

		tsens: thermal-sensor@fc4a9000 {
			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
			reg = <0xfc4a9000 0x1000>, /* TM */
			      <0xfc4a8000 0x1000>; /* SROT */
			nvmem-cells = <&tsens_mode>,
				      <&tsens_base1>, <&tsens_base2>,
				      <&tsens_use_backup>,
				      <&tsens_mode_backup>,
				      <&tsens_base1_backup>, <&tsens_base2_backup>,
				      <&tsens_s0_p1>, <&tsens_s0_p2>,
				      <&tsens_s1_p1>, <&tsens_s1_p2>,
				      <&tsens_s2_p1>, <&tsens_s2_p2>,
				      <&tsens_s3_p1>, <&tsens_s3_p2>,
				      <&tsens_s4_p1>, <&tsens_s4_p2>,
				      <&tsens_s5_p1>, <&tsens_s5_p2>,
				      <&tsens_s6_p1>, <&tsens_s6_p2>,
				      <&tsens_s7_p1>, <&tsens_s7_p2>,
				      <&tsens_s8_p1>, <&tsens_s8_p2>,
				      <&tsens_s9_p1>, <&tsens_s9_p2>,
				      <&tsens_s10_p1>, <&tsens_s10_p2>,
				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
			nvmem-cell-names = "mode",
					   "base1", "base2",
					   "use_backup",
					   "mode_backup",
					   "base1_backup", "base2_backup",
					   "s0_p1", "s0_p2",
					   "s1_p1", "s1_p2",
					   "s2_p1", "s2_p2",
					   "s3_p1", "s3_p2",
					   "s4_p1", "s4_p2",
					   "s5_p1", "s5_p2",
					   "s6_p1", "s6_p2",
					   "s7_p1", "s7_p2",
					   "s8_p1", "s8_p2",
					   "s9_p1", "s9_p2",
					   "s10_p1", "s10_p2",
					   "s0_p1_backup", "s0_p2_backup",
					   "s1_p1_backup", "s1_p2_backup",
					   "s2_p1_backup", "s2_p2_backup",
					   "s3_p1_backup", "s3_p2_backup",
					   "s4_p1_backup", "s4_p2_backup",
					   "s5_p1_backup", "s5_p2_backup",
					   "s6_p1_backup", "s6_p2_backup",
					   "s7_p1_backup", "s7_p2_backup",
					   "s8_p1_backup", "s8_p2_backup",
					   "s9_p1_backup", "s9_p2_backup",
					   "s10_p1_backup", "s10_p2_backup";
			#qcom,sensors = <11>;
			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow";
			#thermal-sensor-cells = <1>;
		};

		restart@fc4ab000 {
			compatible = "qcom,pshold";
			reg = <0xfc4ab000 0x4>;
		};

		qfprom: efuse@fc4bc000 {
			compatible = "qcom,msm8974-qfprom", "qcom,qfprom";
			reg = <0xfc4bc000 0x2100>;
			#address-cells = <1>;
			#size-cells = <1>;

			tsens_base1: base1@d0 {
				reg = <0xd0 0x1>;
				bits = <0 8>;
			};

			tsens_s0_p1: s0-p1@d1 {
				reg = <0xd1 0x1>;
				bits = <0 6>;
			};

			tsens_s1_p1: s1-p1@d2 {
				reg = <0xd1 0x2>;
				bits = <6 6>;
			};

			tsens_s2_p1: s2-p1@d2 {
				reg = <0xd2 0x2>;
				bits = <4 6>;
			};

			tsens_s3_p1: s3-p1@d3 {
				reg = <0xd3 0x1>;
				bits = <2 6>;
			};

			tsens_s4_p1: s4-p1@d4 {
				reg = <0xd4 0x1>;
				bits = <0 6>;
			};

			tsens_s5_p1: s5-p1@d4 {
				reg = <0xd4 0x2>;
				bits = <6 6>;
			};

			tsens_s6_p1: s6-p1@d5 {
				reg = <0xd5 0x2>;
				bits = <4 6>;
			};

			tsens_s7_p1: s7-p1@d6 {
				reg = <0xd6 0x1>;
				bits = <2 6>;
			};

			tsens_s8_p1: s8-p1@d7 {
				reg = <0xd7 0x1>;
				bits = <0 6>;
			};

			tsens_mode: mode@d7 {
				reg = <0xd7 0x1>;
				bits = <6 2>;
			};

			tsens_s9_p1: s9-p1@d8 {
				reg = <0xd8 0x1>;
				bits = <0 6>;
			};

			tsens_s10_p1: s10-p1@d8 {
				reg = <0xd8 0x2>;
				bits = <6 6>;
			};

			tsens_base2: base2@d9 {
				reg = <0xd9 0x2>;
				bits = <4 8>;
			};

			tsens_s0_p2: s0-p2@da {
				reg = <0xda 0x2>;
				bits = <4 6>;
			};

			tsens_s1_p2: s1-p2@db {
				reg = <0xdb 0x1>;
				bits = <2 6>;
			};

			tsens_s2_p2: s2-p2@dc {
				reg = <0xdc 0x1>;
				bits = <0 6>;
			};

			tsens_s3_p2: s3-p2@dc {
				reg = <0xdc 0x2>;
				bits = <6 6>;
			};

			tsens_s4_p2: s4-p2@dd {
				reg = <0xdd 0x2>;
				bits = <4 6>;
			};

			tsens_s5_p2: s5-p2@de {
				reg = <0xde 0x2>;
				bits = <2 6>;
			};

			tsens_s6_p2: s6-p2@df {
				reg = <0xdf 0x1>;
				bits = <0 6>;
			};

			tsens_s7_p2: s7-p2@e0 {
				reg = <0xe0 0x1>;
				bits = <0 6>;
			};

			tsens_s8_p2: s8-p2@e0 {
				reg = <0xe0 0x2>;
				bits = <6 6>;
			};

			tsens_s9_p2: s9-p2@e1 {
				reg = <0xe1 0x2>;
				bits = <4 6>;
			};

			tsens_s10_p2: s10-p2@e2 {
				reg = <0xe2 0x2>;
				bits = <2 6>;
			};

			tsens_s5_p2_backup: s5-p2-backup@e3 {
				reg = <0xe3 0x2>;
				bits = <0 6>;
			};

			tsens_mode_backup: mode-backup@e3 {
				reg = <0xe3 0x1>;
				bits = <6 2>;
			};

			tsens_s6_p2_backup: s6-p2-backup@e4 {
				reg = <0xe4 0x1>;
				bits = <0 6>;
			};

			tsens_s7_p2_backup: s7-p2-backup@e4 {
				reg = <0xe4 0x2>;
				bits = <6 6>;
			};

			tsens_s8_p2_backup: s8-p2-backup@e5 {
				reg = <0xe5 0x2>;
				bits = <4 6>;
			};

			tsens_s9_p2_backup: s9-p2-backup@e6 {
				reg = <0xe6 0x2>;
				bits = <2 6>;
			};

			tsens_s10_p2_backup: s10-p2-backup@e7 {
				reg = <0xe7 0x1>;
				bits = <0 6>;
			};

			tsens_base1_backup: base1-backup@440 {
				reg = <0x440 0x1>;
				bits = <0 8>;
			};

			tsens_s0_p1_backup: s0-p1-backup@441 {
				reg = <0x441 0x1>;
				bits = <0 6>;
			};

			tsens_s1_p1_backup: s1-p1-backup@442 {
				reg = <0x441 0x2>;
				bits = <6 6>;
			};

			tsens_s2_p1_backup: s2-p1-backup@442 {
				reg = <0x442 0x2>;
				bits = <4 6>;
			};

			tsens_s3_p1_backup: s3-p1-backup@443 {
				reg = <0x443 0x1>;
				bits = <2 6>;
			};

			tsens_s4_p1_backup: s4-p1-backup@444 {
				reg = <0x444 0x1>;
				bits = <0 6>;
			};

			tsens_s5_p1_backup: s5-p1-backup@444 {
				reg = <0x444 0x2>;
				bits = <6 6>;
			};

			tsens_s6_p1_backup: s6-p1-backup@445 {
				reg = <0x445 0x2>;
				bits = <4 6>;
			};

			tsens_s7_p1_backup: s7-p1-backup@446 {
				reg = <0x446 0x1>;
				bits = <2 6>;
			};

			tsens_use_backup: use-backup@447 {
				reg = <0x447 0x1>;
				bits = <5 3>;
			};

			tsens_s8_p1_backup: s8-p1-backup@448 {
				reg = <0x448 0x1>;
				bits = <0 6>;
			};

			tsens_s9_p1_backup: s9-p1-backup@448 {
				reg = <0x448 0x2>;
				bits = <6 6>;
			};

			tsens_s10_p1_backup: s10-p1-backup@449 {
				reg = <0x449 0x2>;
				bits = <4 6>;
			};

			tsens_base2_backup: base2-backup@44a {
				reg = <0x44a 0x2>;
				bits = <2 8>;
			};

			tsens_s0_p2_backup: s0-p2-backup@44b {
				reg = <0x44b 0x3>;
				bits = <2 6>;
			};

			tsens_s1_p2_backup: s1-p2-backup@44c {
				reg = <0x44c 0x1>;
				bits = <0 6>;
			};

			tsens_s2_p2_backup: s2-p2-backup@44c {
				reg = <0x44c 0x2>;
				bits = <6 6>;
			};

			tsens_s3_p2_backup: s3-p2-backup@44d {
				reg = <0x44d 0x2>;
				bits = <4 6>;
			};

			tsens_s4_p2_backup: s4-p2-backup@44e {
				reg = <0x44e 0x1>;
				bits = <2 6>;
			};
		};

		spmi_bus: spmi@fc4cf000 {
			compatible = "qcom,spmi-pmic-arb";
			reg-names = "core", "intr", "cnfg";
			reg = <0xfc4cf000 0x1000>,
			      <0xfc4cb000 0x1000>,
			      <0xfc4ca000 0x1000>;
			interrupt-names = "periph_irq";
			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		bam_dmux_dma: dma-controller@fc834000 {
			compatible = "qcom,bam-v1.4.0";
			reg = <0xfc834000 0x7000>;
			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			qcom,ee = <0>;

			num-channels = <6>;
			qcom,num-ees = <1>;
			qcom,powered-remotely;
		};

		remoteproc_mss: remoteproc@fc880000 {
			compatible = "qcom,msm8974-mss-pil";
			reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
			reg-names = "qdsp6", "rmb";

			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";

			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
				 <&gcc GCC_MSS_CFG_AHB_CLK>,
				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
				 <&xo_board>;
			clock-names = "iface", "bus", "mem", "xo";

			resets = <&gcc GCC_MSS_RESTART>;
			reset-names = "mss_restart";

			power-domains = <&rpmpd MSM8974_VDDCX>;
			power-domain-names = "cx";

			qcom,halt-regs = <&tcsr_mutex 0x1180 0x1200 0x1280>;

			qcom,smem-states = <&modem_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			mba {
				memory-region = <&mba_region>;
			};

			mpss {
				memory-region = <&mpss_region>;
			};

			bam_dmux: bam-dmux {
				compatible = "qcom,bam-dmux";

				interrupt-parent = <&modem_smsm>;
				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
				interrupt-names = "pc", "pc-ack";

				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
				qcom,smem-state-names = "pc", "pc-ack";

				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
				dma-names = "tx", "rx";
			};

			smd-edge {
				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;

				mboxes = <&apcs 12>;
				qcom,smd-edge = <0>;

				label = "modem";
			};
		};

		tcsr_mutex: hwlock@fd484000 {
			compatible = "qcom,msm8974-tcsr-mutex", "qcom,tcsr-mutex", "syscon";
			reg = <0xfd484000 0x2000>;
			#hwlock-cells = <1>;
		};

		tcsr: syscon@fd4a0000 {
			compatible = "qcom,tcsr-msm8974", "syscon";
			reg = <0xfd4a0000 0x10000>;
		};

		tlmm: pinctrl@fd510000 {
			compatible = "qcom,msm8974-pinctrl";
			reg = <0xfd510000 0x4000>;
			gpio-controller;
			gpio-ranges = <&tlmm 0 0 146>;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;

			sdc1_off: sdc1-off-state {
				clk-pins {
					pins = "sdc1_clk";
					bias-disable;
					drive-strength = <2>;
				};

				cmd-pins {
					pins = "sdc1_cmd";
					bias-pull-up;
					drive-strength = <2>;
				};

				data-pins {
					pins = "sdc1_data";
					bias-pull-up;
					drive-strength = <2>;
				};
			};

			sdc2_off: sdc2-off-state {
				clk-pins {
					pins = "sdc2_clk";
					bias-disable;
					drive-strength = <2>;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					bias-pull-up;
					drive-strength = <2>;
				};

				data-pins {
					pins = "sdc2_data";
					bias-pull-up;
					drive-strength = <2>;
				};
			};

			blsp1_uart2_default: blsp1-uart2-default-state {
				rx-pins {
					pins = "gpio5";
					function = "blsp_uart2";
					drive-strength = <2>;
					bias-pull-up;
				};

				tx-pins {
					pins = "gpio4";
					function = "blsp_uart2";
					drive-strength = <4>;
					bias-disable;
				};
			};

			blsp2_uart1_default: blsp2-uart1-default-state {
				tx-rts-pins {
					pins = "gpio41", "gpio44";
					function = "blsp_uart7";
					drive-strength = <2>;
					bias-disable;
				};

				rx-cts-pins {
					pins = "gpio42", "gpio43";
					function = "blsp_uart7";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			blsp2_uart1_sleep: blsp2-uart1-sleep-state {
				pins = "gpio41", "gpio42", "gpio43", "gpio44";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			blsp2_uart4_default: blsp2-uart4-default-state {
				tx-rts-pins {
					pins = "gpio53", "gpio56";
					function = "blsp_uart10";
					drive-strength = <2>;
					bias-disable;
				};

				rx-cts-pins {
					pins = "gpio54", "gpio55";
					function = "blsp_uart10";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			blsp1_i2c1_default: blsp1-i2c1-default-state {
				pins = "gpio2", "gpio3";
				function = "blsp_i2c1";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c1_sleep: blsp1-i2c1-sleep-state {
				pins = "gpio2", "gpio3";
				function = "blsp_i2c1";
				drive-strength = <2>;
				bias-pull-up;
			};

			blsp1_i2c2_default: blsp1-i2c2-default-state {
				pins = "gpio6", "gpio7";
				function = "blsp_i2c2";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c2_sleep: blsp1-i2c2-sleep-state {
				pins = "gpio6", "gpio7";
				function = "blsp_i2c2";
				drive-strength = <2>;
				bias-pull-up;
			};

			blsp1_i2c3_default: blsp1-i2c3-default-state {
				pins = "gpio10", "gpio11";
				function = "blsp_i2c3";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c3_sleep: blsp1-i2c3-sleep-state {
				pins = "gpio10", "gpio11";
				function = "blsp_i2c3";
				drive-strength = <2>;
				bias-pull-up;
			};

			/* BLSP1_I2C4 info is missing */

			/* BLSP1_I2C5 info is missing */

			blsp1_i2c6_default: blsp1-i2c6-default-state {
				pins = "gpio29", "gpio30";
				function = "blsp_i2c6";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
				pins = "gpio29", "gpio30";
				function = "blsp_i2c6";
				drive-strength = <2>;
				bias-pull-up;
			};
			/* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */

			/* BLSP2_I2C1 info is missing */

			blsp2_i2c2_default: blsp2-i2c2-default-state {
				pins = "gpio47", "gpio48";
				function = "blsp_i2c8";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c2_sleep: blsp2-i2c2-sleep-state {
				pins = "gpio47", "gpio48";
				function = "blsp_i2c8";
				drive-strength = <2>;
				bias-pull-up;
			};

			/* BLSP2_I2C3 info is missing */

			/* BLSP2_I2C4 info is missing */

			blsp2_i2c5_default: blsp2-i2c5-default-state {
				pins = "gpio83", "gpio84";
				function = "blsp_i2c11";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c5_sleep: blsp2-i2c5-sleep-state {
				pins = "gpio83", "gpio84";
				function = "blsp_i2c11";
				drive-strength = <2>;
				bias-pull-up;
			};

			blsp2_i2c6_default: blsp2-i2c6-default-state {
				pins = "gpio87", "gpio88";
				function = "blsp_i2c12";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c6_sleep: blsp2-i2c6-sleep-state {
				pins = "gpio87", "gpio88";
				function = "blsp_i2c12";
				drive-strength = <2>;
				bias-pull-up;
			};

			cci_default: cci-default-state {
				cci_i2c0_default: cci-i2c0-default-pins {
					pins = "gpio19", "gpio20";
					function = "cci_i2c0";
					drive-strength = <2>;
					bias-disable;
				};

				cci_i2c1_default: cci-i2c1-default-pins {
					pins = "gpio21", "gpio22";
					function = "cci_i2c1";
					drive-strength = <2>;
					bias-disable;
				};
			};

			cci_sleep: cci-sleep-state {
				cci_i2c0_sleep: cci-i2c0-sleep-pins {
					pins = "gpio19", "gpio20";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};

				cci_i2c1_sleep: cci-i2c1-sleep-pins {
					pins = "gpio21", "gpio22";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};
			};

			spi8_default: spi8-default-state {
				mosi-pins {
					pins = "gpio45";
					function = "blsp_spi8";
				};
				miso-pins {
					pins = "gpio46";
					function = "blsp_spi8";
				};
				cs-pins {
					pins = "gpio47";
					function = "blsp_spi8";
				};
				clk-pins {
					pins = "gpio48";
					function = "blsp_spi8";
				};
			};
		};

		mmcc: clock-controller@fd8c0000 {
			compatible = "qcom,mmcc-msm8974";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			reg = <0xfd8c0000 0x6000>;
			clocks = <&xo_board>,
				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
				 <&gcc GPLL0_VOTE>,
				 <&gcc GPLL1_VOTE>,
				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
				 <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>,
				 <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>,
				 <&mdss_dsi1_phy DSI_PIXEL_PLL_CLK>,
				 <&mdss_dsi1_phy DSI_BYTE_PLL_CLK>,
				 <0>,
				 <0>,
				 <0>;
			clock-names = "xo",
				      "mmss_gpll0_vote",
				      "gpll0_vote",
				      "gpll1_vote",
				      "gfx3d_clk_src",
				      "dsi0pll",
				      "dsi0pllbyte",
				      "dsi1pll",
				      "dsi1pllbyte",
				      "hdmipll",
				      "edp_link_clk",
				      "edp_vco_div";
		};

		mdss: display-subsystem@fd900000 {
			compatible = "qcom,mdss";
			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
			reg-names = "mdss_phys", "vbif_phys";

			power-domains = <&mmcc MDSS_GDSC>;

			clocks = <&mmcc MDSS_AHB_CLK>,
				 <&mmcc MDSS_AXI_CLK>,
				 <&mmcc MDSS_VSYNC_CLK>;
			clock-names = "iface", "bus", "vsync";

			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;

			interrupt-controller;
			#interrupt-cells = <1>;

			status = "disabled";

			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			mdp: display-controller@fd900000 {
				compatible = "qcom,msm8974-mdp5", "qcom,mdp5";
				reg = <0xfd900100 0x22000>;
				reg-names = "mdp_phys";

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_VSYNC_CLK>;
				clock-names = "iface", "bus", "core", "vsync";

				interconnects = <&mmssnoc MNOC_MAS_MDP_PORT0 &bimc BIMC_SLV_EBI_CH0>;
				interconnect-names = "mdp0-mem";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdp5_intf1_out: endpoint {
							remote-endpoint = <&mdss_dsi0_in>;
						};
					};

					port@1 {
						reg = <1>;
						mdp5_intf2_out: endpoint {
							remote-endpoint = <&mdss_dsi1_in>;
						};
					};
				};
			};

			mdss_dsi0: dsi@fd922800 {
				compatible = "qcom,msm8974-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0xfd922800 0x1f8>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
						  <&mmcc PCLK0_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>,
							 <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>;

				clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MDSS_BYTE0_CLK>,
					 <&mmcc MDSS_PCLK0_CLK>,
					 <&mmcc MDSS_ESC0_CLK>,
					 <&mmcc MMSS_MISC_AHB_CLK>;
				clock-names = "mdp_core",
					      "iface",
					      "bus",
					      "byte",
					      "pixel",
					      "core",
					      "core_mmss";

				phys = <&mdss_dsi0_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi0_in: endpoint {
							remote-endpoint = <&mdp5_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi0_out: endpoint {
						};
					};
				};
			};

			mdss_dsi0_phy: phy@fd922a00 {
				compatible = "qcom,dsi-phy-28nm-hpm";
				reg = <0xfd922a00 0xd4>,
				      <0xfd922b00 0x280>,
				      <0xfd922d80 0x30>;
				reg-names = "dsi_pll",
					    "dsi_phy",
					    "dsi_phy_regulator";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			mdss_dsi1: dsi@fd922e00 {
				compatible = "qcom,msm8974-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0xfd922e00 0x1f8>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				assigned-clocks = <&mmcc BYTE1_CLK_SRC>,
						  <&mmcc PCLK1_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi1_phy DSI_BYTE_PLL_CLK>,
							 <&mdss_dsi1_phy DSI_PIXEL_PLL_CLK>;

				clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MDSS_BYTE1_CLK>,
					 <&mmcc MDSS_PCLK1_CLK>,
					 <&mmcc MDSS_ESC1_CLK>,
					 <&mmcc MMSS_MISC_AHB_CLK>;
				clock-names = "mdp_core",
					      "iface",
					      "bus",
					      "byte",
					      "pixel",
					      "core",
					      "core_mmss";

				phys = <&mdss_dsi1_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi1_in: endpoint {
							remote-endpoint = <&mdp5_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi1_out: endpoint {
						};
					};
				};
			};

			mdss_dsi1_phy: phy@fd923000 {
				compatible = "qcom,dsi-phy-28nm-hpm";
				reg = <0xfd923000 0xd4>,
				      <0xfd923100 0x280>,
				      <0xfd923380 0x30>;
				reg-names = "dsi_pll",
					    "dsi_phy",
					    "dsi_phy_regulator";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
				clock-names = "iface", "ref";

				status = "disabled";
			};
		};

		cci: cci@fda0c000 {
			compatible = "qcom,msm8974-cci";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0xfda0c000 0x1000>;
			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
				 <&mmcc CAMSS_CCI_CCI_CLK>;
			clock-names = "camss_top_ahb",
				      "cci_ahb",
				      "cci";

			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&cci_default>;
			pinctrl-1 = <&cci_sleep>;

			status = "disabled";

			cci_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <100000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <100000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gpu: gpu@fdb00000 {
			compatible = "qcom,adreno-330.1", "qcom,adreno";
			reg = <0xfdb00000 0x10000>;
			reg-names = "kgsl_3d0_reg_memory";

			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "kgsl_3d0_irq";

			clocks = <&mmcc OXILI_GFX3D_CLK>,
				 <&mmcc OXILICX_AHB_CLK>,
				 <&mmcc OXILICX_AXI_CLK>;
			clock-names = "core", "iface", "mem_iface";

			sram = <&gmu_sram>;
			power-domains = <&mmcc OXILICX_GDSC>;
			operating-points-v2 = <&gpu_opp_table>;

			interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>,
					<&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>;
			interconnect-names = "gfx-mem", "ocmem";

			// iommus = <&gpu_iommu 0>;

			status = "disabled";

			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-320000000 {
					opp-hz = /bits/ 64 <320000000>;
				};

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
				};

				opp-27000000 {
					opp-hz = /bits/ 64 <27000000>;
				};
			};
		};

		sram@fdd00000 {
			compatible = "qcom,msm8974-ocmem";
			reg = <0xfdd00000 0x2000>,
			      <0xfec00000 0x180000>;
			reg-names = "ctrl", "mem";
			ranges = <0 0xfec00000 0x180000>;
			/* core clock doesn't exist anymore, kept for ABI compliance */
			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
				 <&mmcc OCMEMCX_OCMEMNOC_CLK>;
			clock-names = "core", "iface";

			#address-cells = <1>;
			#size-cells = <1>;

			gmu_sram: gmu-sram@0 {
				reg = <0x0 0x100000>;
			};
		};

		remoteproc_adsp: remoteproc@fe200000 {
			compatible = "qcom,msm8974-adsp-pil";
			reg = <0xfe200000 0x100>;

			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
					       <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					       <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					       <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					       <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";

			clocks = <&xo_board>;
			clock-names = "xo";

			power-domains = <&rpmpd MSM8974_VDDCX>;
			power-domain-names = "cx";

			memory-region = <&adsp_region>;

			qcom,smem-states = <&adsp_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			smd-edge {
				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;

				mboxes = <&apcs 8>;
				qcom,smd-edge = <1>;
				label = "lpass";
			};
		};

		imem: sram@fe805000 {
			compatible = "qcom,msm8974-imem", "syscon", "simple-mfd";
			reg = <0xfe805000 0x1000>;

			reboot-mode {
				compatible = "syscon-reboot-mode";
				offset = <0x65c>;
			};
		};
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 5>;

			trips {
				cpu_alert0: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit0: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 6>;

			trips {
				cpu_alert1: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit1: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 7>;

			trips {
				cpu_alert2: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit2: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 8>;

			trips {
				cpu_alert3: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit3: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		q6-dsp-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 1>;

			trips {
				q6_dsp_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modemtx-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 2>;

			trips {
				modemtx_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 3>;

			trips {
				video_alert0: trip-point0 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		wlan-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 4>;

			trips {
				wlan_alert0: trip-point0 {
					temperature = <105000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 9>;

			trips {
				gpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens 10>;

			trips {
				gpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv7-timer";
		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
		clock-frequency = <19200000>;
	};
};