// SPDX-License-Identifier: GPL-2.0-or-later
/*
 *  libata-core.c - helper library for ATA
 *
 *  Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
 *  Copyright 2003-2004 Jeff Garzik
 *
 *  libata documentation is available via 'make {ps|pdf}docs',
 *  as Documentation/driver-api/libata.rst
 *
 *  Hardware documentation available from http://www.t13.org/ and
 *  http://www.sata-io.org/
 *
 *  Standards documents from:
 *	http://www.t13.org (ATA standards, PCI DMA IDE spec)
 *	http://www.t10.org (SCSI MMC - for ATAPI MMC)
 *	http://www.sata-io.org (SATA)
 *	http://www.compactflash.org (CF)
 *	http://www.qic.org (QIC157 - Tape and DSC)
 *	http://www.ce-ata.org (CE-ATA: not supported)
 *
 * libata is essentially a library of internal helper functions for
 * low-level ATA host controller drivers.  As such, the API/ABI is
 * likely to change as new drivers are added and updated.
 * Do not depend on ABI/API stability.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/list.h>
#include <linux/mm.h>
#include <linux/spinlock.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/time.h>
#include <linux/interrupt.h>
#include <linux/completion.h>
#include <linux/suspend.h>
#include <linux/workqueue.h>
#include <linux/scatterlist.h>
#include <linux/io.h>
#include <linux/log2.h>
#include <linux/slab.h>
#include <linux/glob.h>
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <asm/byteorder.h>
#include <linux/unaligned.h>
#include <linux/cdrom.h>
#include <linux/ratelimit.h>
#include <linux/leds.h>
#include <linux/pm_runtime.h>
#include <linux/platform_device.h>
#include <asm/setup.h>

#define CREATE_TRACE_POINTS
#include <trace/events/libata.h>

#include "libata.h"
#include "libata-transport.h"

const struct ata_port_operations ata_base_port_ops = {
	.reset.prereset		= ata_std_prereset,
	.reset.postreset	= ata_std_postreset,
	.error_handler		= ata_std_error_handler,
	.sched_eh		= ata_std_sched_eh,
	.end_eh			= ata_std_end_eh,
};

static unsigned int ata_dev_init_params(struct ata_device *dev,
					u16 heads, u16 sectors);
static unsigned int ata_dev_set_xfermode(struct ata_device *dev);
static void ata_dev_xfermask(struct ata_device *dev);
static u64 ata_dev_quirks(const struct ata_device *dev);
static u64 ata_dev_get_quirk_value(struct ata_device *dev, u64 quirk);

static DEFINE_IDA(ata_ida);

#ifdef CONFIG_ATA_FORCE
struct ata_force_param {
	const char	*name;
	u64		value;
	u8		cbl;
	u8		spd_limit;
	unsigned int	xfer_mask;
	u64		quirk_on;
	u64		quirk_off;
	unsigned int	pflags_on;
	u16		lflags_on;
	u16		lflags_off;
};

struct ata_force_ent {
	int			port;
	int			device;
	struct ata_force_param	param;
};

static struct ata_force_ent *ata_force_tbl;
static int ata_force_tbl_size;

static char ata_force_param_buf[COMMAND_LINE_SIZE] __initdata;
/* param_buf is thrown away after initialization, disallow read */
module_param_string(force, ata_force_param_buf, sizeof(ata_force_param_buf), 0);
MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link speed and transfer mode (see Documentation/admin-guide/kernel-parameters.rst for details)");
#endif

static int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on [default])");

static int atapi_dmadir = 0;
module_param(atapi_dmadir, int, 0444);
MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off [default], 1=on)");

int atapi_passthru16 = 1;
module_param(atapi_passthru16, int, 0444);
MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices (0=off, 1=on [default])");

int libata_fua = 0;
module_param_named(fua, libata_fua, int, 0444);
MODULE_PARM_DESC(fua, "FUA support (0=off [default], 1=on)");

static int ata_ignore_hpa;
module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644);
MODULE_PARM_DESC(ignore_hpa, "Ignore HPA limit (0=keep BIOS limits, 1=ignore limits, using full disk)");

static int libata_dma_mask = ATA_DMA_MASK_ATA|ATA_DMA_MASK_ATAPI|ATA_DMA_MASK_CFA;
module_param_named(dma, libata_dma_mask, int, 0444);
MODULE_PARM_DESC(dma, "DMA enable/disable (0x1==ATA, 0x2==ATAPI, 0x4==CF)");

static int ata_probe_timeout;
module_param(ata_probe_timeout, int, 0444);
MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)");

int libata_noacpi = 0;
module_param_named(noacpi, libata_noacpi, int, 0444);
MODULE_PARM_DESC(noacpi, "Disable the use of ACPI in probe/suspend/resume (0=off [default], 1=on)");

int libata_allow_tpm = 0;
module_param_named(allow_tpm, libata_allow_tpm, int, 0444);
MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands (0=off [default], 1=on)");

static int atapi_an;
module_param(atapi_an, int, 0444);
MODULE_PARM_DESC(atapi_an, "Enable ATAPI AN media presence notification (0=0ff [default], 1=on)");

MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);

static inline bool ata_dev_print_info(const struct ata_device *dev)
{
	struct ata_eh_context *ehc = &dev->link->eh_context;

	return ehc->i.flags & ATA_EHI_PRINTINFO;
}

/**
 *	ata_link_next - link iteration helper
 *	@link: the previous link, NULL to start
 *	@ap: ATA port containing links to iterate
 *	@mode: iteration mode, one of ATA_LITER_*
 *
 *	LOCKING:
 *	Host lock or EH context.
 *
 *	RETURNS:
 *	Pointer to the next link.
 */
struct ata_link *ata_link_next(struct ata_link *link, struct ata_port *ap,
			       enum ata_link_iter_mode mode)
{
	BUG_ON(mode != ATA_LITER_EDGE &&
	       mode != ATA_LITER_PMP_FIRST && mode != ATA_LITER_HOST_FIRST);

	/* NULL link indicates start of iteration */
	if (!link)
		switch (mode) {
		case ATA_LITER_EDGE:
		case ATA_LITER_PMP_FIRST:
			if (sata_pmp_attached(ap))
				return ap->pmp_link;
			fallthrough;
		case ATA_LITER_HOST_FIRST:
			return &ap->link;
		}

	/* we just iterated over the host link, what's next? */
	if (link == &ap->link)
		switch (mode) {
		case ATA_LITER_HOST_FIRST:
			if (sata_pmp_attached(ap))
				return ap->pmp_link;
			fallthrough;
		case ATA_LITER_PMP_FIRST:
			if (unlikely(ap->slave_link))
				return ap->slave_link;
			fallthrough;
		case ATA_LITER_EDGE:
			return NULL;
		}

	/* slave_link excludes PMP */
	if (unlikely(link == ap->slave_link))
		return NULL;

	/* we were over a PMP link */
	if (++link < ap->pmp_link + ap->nr_pmp_links)
		return link;

	if (mode == ATA_LITER_PMP_FIRST)
		return &ap->link;

	return NULL;
}
EXPORT_SYMBOL_GPL(ata_link_next);

/**
 *	ata_dev_next - device iteration helper
 *	@dev: the previous device, NULL to start
 *	@link: ATA link containing devices to iterate
 *	@mode: iteration mode, one of ATA_DITER_*
 *
 *	LOCKING:
 *	Host lock or EH context.
 *
 *	RETURNS:
 *	Pointer to the next device.
 */
struct ata_device *ata_dev_next(struct ata_device *dev, struct ata_link *link,
				enum ata_dev_iter_mode mode)
{
	BUG_ON(mode != ATA_DITER_ENABLED && mode != ATA_DITER_ENABLED_REVERSE &&
	       mode != ATA_DITER_ALL && mode != ATA_DITER_ALL_REVERSE);

	/* NULL dev indicates start of iteration */
	if (!dev)
		switch (mode) {
		case ATA_DITER_ENABLED:
		case ATA_DITER_ALL:
			dev = link->device;
			goto check;
		case ATA_DITER_ENABLED_REVERSE:
		case ATA_DITER_ALL_REVERSE:
			dev = link->device + ata_link_max_devices(link) - 1;
			goto check;
		}

 next:
	/* move to the next one */
	switch (mode) {
	case ATA_DITER_ENABLED:
	case ATA_DITER_ALL:
		if (++dev < link->device + ata_link_max_devices(link))
			goto check;
		return NULL;
	case ATA_DITER_ENABLED_REVERSE:
	case ATA_DITER_ALL_REVERSE:
		if (--dev >= link->device)
			goto check;
		return NULL;
	}

 check:
	if ((mode == ATA_DITER_ENABLED || mode == ATA_DITER_ENABLED_REVERSE) &&
	    !ata_dev_enabled(dev))
		goto next;
	return dev;
}
EXPORT_SYMBOL_GPL(ata_dev_next);

/**
 *	ata_dev_phys_link - find physical link for a device
 *	@dev: ATA device to look up physical link for
 *
 *	Look up physical link which @dev is attached to.  Note that
 *	this is different from @dev->link only when @dev is on slave
 *	link.  For all other cases, it's the same as @dev->link.
 *
 *	LOCKING:
 *	Don't care.
 *
 *	RETURNS:
 *	Pointer to the found physical link.
 */
struct ata_link *ata_dev_phys_link(struct ata_device *dev)
{
	struct ata_port *ap = dev->link->ap;

	if (!ap->slave_link)
		return dev->link;
	if (!dev->devno)
		return &ap->link;
	return ap->slave_link;
}

#ifdef CONFIG_ATA_FORCE
/**
 *	ata_force_cbl - force cable type according to libata.force
 *	@ap: ATA port of interest
 *
 *	Force cable type according to libata.force and whine about it.
 *	The last entry which has matching port number is used, so it
 *	can be specified as part of device force parameters.  For
 *	example, both "a:40c,1.00:udma4" and "1.00:40c,udma4" have the
 *	same effect.
 *
 *	LOCKING:
 *	EH context.
 */
void ata_force_cbl(struct ata_port *ap)
{
	int i;

	for (i = ata_force_tbl_size - 1; i >= 0; i--) {
		const struct ata_force_ent *fe = &ata_force_tbl[i];

		if (fe->port != -1 && fe->port != ap->print_id)
			continue;

		if (fe->param.cbl == ATA_CBL_NONE)
			continue;

		ap->cbl = fe->param.cbl;
		ata_port_notice(ap, "FORCE: cable set to %s\n", fe->param.name);
		return;
	}
}

/**
 *	ata_force_pflags - force port flags according to libata.force
 *	@ap: ATA port of interest
 *
 *	Force port flags according to libata.force and whine about it.
 *
 *	LOCKING:
 *	EH context.
 */
static void ata_force_pflags(struct ata_port *ap)
{
	int i;

	for (i = ata_force_tbl_size - 1; i >= 0; i--) {
		const struct ata_force_ent *fe = &ata_force_tbl[i];

		if (fe->port != -1 && fe->port != ap->print_id)
			continue;

		/* let pflags stack */
		if (fe->param.pflags_on) {
			ap->pflags |= fe->param.pflags_on;
			ata_port_notice(ap,
					"FORCE: port flag 0x%x forced -> 0x%x\n",
					fe->param.pflags_on, ap->pflags);
		}
	}
}

/**
 *	ata_force_link_limits - force link limits according to libata.force
 *	@link: ATA link of interest
 *
 *	Force link flags and SATA spd limit according to libata.force
 *	and whine about it.  When only the port part is specified
 *	(e.g. 1:), the limit applies to all links connected to both
 *	the host link and all fan-out ports connected via PMP.  If the
 *	device part is specified as 0 (e.g. 1.00:), it specifies the
 *	first fan-out link not the host link.  Device number 15 always
 *	points to the host link whether PMP is attached or not.  If the
 *	controller has slave link, device number 16 points to it.
 *
 *	LOCKING:
 *	EH context.
 */
static void ata_force_link_limits(struct ata_link *link)
{
	bool did_spd = false;
	int linkno = link->pmp;
	int i;

	if (ata_is_host_link(link))
		linkno += 15;

	for (i = ata_force_tbl_size - 1; i >= 0; i--) {
		const struct ata_force_ent *fe = &ata_force_tbl[i];

		if (fe->port != -1 && fe->port != link->ap->print_id)
			continue;

		if (fe->device != -1 && fe->device != linkno)
			continue;

		/* only honor the first spd limit */
		if (!did_spd && fe->param.spd_limit) {
			link->hw_sata_spd_limit = (1 << fe->param.spd_limit) - 1;
			ata_link_notice(link, "FORCE: PHY spd limit set to %s\n",
					fe->param.name);
			did_spd = true;
		}

		/* let lflags stack */
		if (fe->param.lflags_on) {
			link->flags |= fe->param.lflags_on;
			ata_link_notice(link,
					"FORCE: link flag 0x%x forced -> 0x%x\n",
					fe->param.lflags_on, link->flags);
		}
		if (fe->param.lflags_off) {
			link->flags &= ~fe->param.lflags_off;
			ata_link_notice(link,
				"FORCE: link flag 0x%x cleared -> 0x%x\n",
				fe->param.lflags_off, link->flags);
		}
	}
}

/**
 *	ata_force_xfermask - force xfermask according to libata.force
 *	@dev: ATA device of interest
 *
 *	Force xfer_mask according to libata.force and whine about it.
 *	For consistency with link selection, device number 15 selects
 *	the first device connected to the host link.
 *
 *	LOCKING:
 *	EH context.
 */
static void ata_force_xfermask(struct ata_device *dev)
{
	int devno = dev->link->pmp + dev->devno;
	int alt_devno = devno;
	int i;

	/* allow n.15/16 for devices attached to host port */
	if (ata_is_host_link(dev->link))
		alt_devno += 15;

	for (i = ata_force_tbl_size - 1; i >= 0; i--) {
		const struct ata_force_ent *fe = &ata_force_tbl[i];
		unsigned int pio_mask, mwdma_mask, udma_mask;

		if (fe->port != -1 && fe->port != dev->link->ap->print_id)
			continue;

		if (fe->device != -1 && fe->device != devno &&
		    fe->device != alt_devno)
			continue;

		if (!fe->param.xfer_mask)
			continue;

		ata_unpack_xfermask(fe->param.xfer_mask,
				    &pio_mask, &mwdma_mask, &udma_mask);
		if (udma_mask)
			dev->udma_mask = udma_mask;
		else if (mwdma_mask) {
			dev->udma_mask = 0;
			dev->mwdma_mask = mwdma_mask;
		} else {
			dev->udma_mask = 0;
			dev->mwdma_mask = 0;
			dev->pio_mask = pio_mask;
		}

		ata_dev_notice(dev, "FORCE: xfer_mask set to %s\n",
			       fe->param.name);
		return;
	}
}

static const struct ata_force_ent *
ata_force_get_fe_for_dev(struct ata_device *dev)
{
	const struct ata_force_ent *fe;
	int devno = dev->link->pmp + dev->devno;
	int alt_devno = devno;
	int i;

	/* allow n.15/16 for devices attached to host port */
	if (ata_is_host_link(dev->link))
		alt_devno += 15;

	for (i = 0; i < ata_force_tbl_size; i++) {
		fe = &ata_force_tbl[i];
		if (fe->port != -1 && fe->port != dev->link->ap->print_id)
			continue;

		if (fe->device != -1 && fe->device != devno &&
		    fe->device != alt_devno)
			continue;

		return fe;
	}

	return NULL;
}

/**
 *	ata_force_quirks - force quirks according to libata.force
 *	@dev: ATA device of interest
 *
 *	Force quirks according to libata.force and whine about it.
 *	For consistency with link selection, device number 15 selects
 *	the first device connected to the host link.
 *
 *	LOCKING:
 *	EH context.
 */
static void ata_force_quirks(struct ata_device *dev)
{
	const struct ata_force_ent *fe = ata_force_get_fe_for_dev(dev);

	if (!fe)
		return;

	if (!(~dev->quirks & fe->param.quirk_on) &&
	    !(dev->quirks & fe->param.quirk_off))
		return;

	dev->quirks |= fe->param.quirk_on;
	dev->quirks &= ~fe->param.quirk_off;

	ata_dev_notice(dev, "FORCE: modified (%s)\n", fe->param.name);
}
#else
static inline void ata_force_pflags(struct ata_port *ap) { }
static inline void ata_force_link_limits(struct ata_link *link) { }
static inline void ata_force_xfermask(struct ata_device *dev) { }
static inline void ata_force_quirks(struct ata_device *dev) { }
#endif

/**
 *	atapi_cmd_type - Determine ATAPI command type from SCSI opcode
 *	@opcode: SCSI opcode
 *
 *	Determine ATAPI command type from @opcode.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	ATAPI_{READ|WRITE|READ_CD|PASS_THRU|MISC}
 */
int atapi_cmd_type(u8 opcode)
{
	switch (opcode) {
	case GPCMD_READ_10:
	case GPCMD_READ_12:
		return ATAPI_READ;

	case GPCMD_WRITE_10:
	case GPCMD_WRITE_12:
	case GPCMD_WRITE_AND_VERIFY_10:
		return ATAPI_WRITE;

	case GPCMD_READ_CD:
	case GPCMD_READ_CD_MSF:
		return ATAPI_READ_CD;

	case ATA_16:
	case ATA_12:
		if (atapi_passthru16)
			return ATAPI_PASS_THRU;
		fallthrough;
	default:
		return ATAPI_MISC;
	}
}
EXPORT_SYMBOL_GPL(atapi_cmd_type);

static const u8 ata_rw_cmds[] = {
	/* pio multi */
	ATA_CMD_READ_MULTI,
	ATA_CMD_WRITE_MULTI,
	ATA_CMD_READ_MULTI_EXT,
	ATA_CMD_WRITE_MULTI_EXT,
	0,
	0,
	0,
	0,
	/* pio */
	ATA_CMD_PIO_READ,
	ATA_CMD_PIO_WRITE,
	ATA_CMD_PIO_READ_EXT,
	ATA_CMD_PIO_WRITE_EXT,
	0,
	0,
	0,
	0,
	/* dma */
	ATA_CMD_READ,
	ATA_CMD_WRITE,
	ATA_CMD_READ_EXT,
	ATA_CMD_WRITE_EXT,
	0,
	0,
	0,
	ATA_CMD_WRITE_FUA_EXT
};

/**
 *	ata_set_rwcmd_protocol - set taskfile r/w command and protocol
 *	@dev: target device for the taskfile
 *	@tf: taskfile to examine and configure
 *
 *	Examine the device configuration and tf->flags to determine
 *	the proper read/write command and protocol to use for @tf.
 *
 *	LOCKING:
 *	caller.
 */
static bool ata_set_rwcmd_protocol(struct ata_device *dev,
				   struct ata_taskfile *tf)
{
	u8 cmd;

	int index, fua, lba48, write;

	fua = (tf->flags & ATA_TFLAG_FUA) ? 4 : 0;
	lba48 = (tf->flags & ATA_TFLAG_LBA48) ? 2 : 0;
	write = (tf->flags & ATA_TFLAG_WRITE) ? 1 : 0;

	if (dev->flags & ATA_DFLAG_PIO) {
		tf->protocol = ATA_PROT_PIO;
		index = dev->multi_count ? 0 : 8;
	} else if (lba48 && (dev->link->ap->flags & ATA_FLAG_PIO_LBA48)) {
		/* Unable to use DMA due to host limitation */
		tf->protocol = ATA_PROT_PIO;
		index = dev->multi_count ? 0 : 8;
	} else {
		tf->protocol = ATA_PROT_DMA;
		index = 16;
	}

	cmd = ata_rw_cmds[index + fua + lba48 + write];
	if (!cmd)
		return false;

	tf->command = cmd;

	return true;
}

/**
 *	ata_tf_read_block - Read block address from ATA taskfile
 *	@tf: ATA taskfile of interest
 *	@dev: ATA device @tf belongs to
 *
 *	LOCKING:
 *	None.
 *
 *	Read block address from @tf.  This function can handle all
 *	three address formats - LBA, LBA48 and CHS.  tf->protocol and
 *	flags select the address format to use.
 *
 *	RETURNS:
 *	Block address read from @tf.
 */
u64 ata_tf_read_block(const struct ata_taskfile *tf, struct ata_device *dev)
{
	u64 block = 0;

	if (tf->flags & ATA_TFLAG_LBA) {
		if (tf->flags & ATA_TFLAG_LBA48) {
			block |= (u64)tf->hob_lbah << 40;
			block |= (u64)tf->hob_lbam << 32;
			block |= (u64)tf->hob_lbal << 24;
		} else
			block |= (tf->device & 0xf) << 24;

		block |= tf->lbah << 16;
		block |= tf->lbam << 8;
		block |= tf->lbal;
	} else {
		u32 cyl, head, sect;

		cyl = tf->lbam | (tf->lbah << 8);
		head = tf->device & 0xf;
		sect = tf->lbal;

		if (!sect) {
			ata_dev_warn(dev,
				     "device reported invalid CHS sector 0\n");
			return U64_MAX;
		}

		block = (cyl * dev->heads + head) * dev->sectors + sect - 1;
	}

	return block;
}

/*
 * Set a taskfile command duration limit index.
 */
static inline void ata_set_tf_cdl(struct ata_queued_cmd *qc, int cdl)
{
	struct ata_taskfile *tf = &qc->tf;

	if (tf->protocol == ATA_PROT_NCQ)
		tf->auxiliary |= cdl;
	else
		tf->feature |= cdl;

	/*
	 * Mark this command as having a CDL and request the result
	 * task file so that we can inspect the sense data available
	 * bit on completion.
	 */
	qc->flags |= ATA_QCFLAG_HAS_CDL | ATA_QCFLAG_RESULT_TF;
}

/**
 *	ata_build_rw_tf - Build ATA taskfile for given read/write request
 *	@qc: Metadata associated with the taskfile to build
 *	@block: Block address
 *	@n_block: Number of blocks
 *	@tf_flags: RW/FUA etc...
 *	@cdl: Command duration limit index
 *	@class: IO priority class
 *
 *	LOCKING:
 *	None.
 *
 *	Build ATA taskfile for the command @qc for read/write request described
 *	by @block, @n_block, @tf_flags and @class.
 *
 *	RETURNS:
 *
 *	0 on success, -ERANGE if the request is too large for @dev,
 *	-EINVAL if the request is invalid.
 */
int ata_build_rw_tf(struct ata_queued_cmd *qc, u64 block, u32 n_block,
		    unsigned int tf_flags, int cdl, int class)
{
	struct ata_taskfile *tf = &qc->tf;
	struct ata_device *dev = qc->dev;

	tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
	tf->flags |= tf_flags;

	if (ata_ncq_enabled(dev)) {
		/* yay, NCQ */
		if (!lba_48_ok(block, n_block))
			return -ERANGE;

		tf->protocol = ATA_PROT_NCQ;
		tf->flags |= ATA_TFLAG_LBA | ATA_TFLAG_LBA48;

		if (tf->flags & ATA_TFLAG_WRITE)
			tf->command = ATA_CMD_FPDMA_WRITE;
		else
			tf->command = ATA_CMD_FPDMA_READ;

		tf->nsect = qc->hw_tag << 3;
		tf->hob_feature = (n_block >> 8) & 0xff;
		tf->feature = n_block & 0xff;

		tf->hob_lbah = (block >> 40) & 0xff;
		tf->hob_lbam = (block >> 32) & 0xff;
		tf->hob_lbal = (block >> 24) & 0xff;
		tf->lbah = (block >> 16) & 0xff;
		tf->lbam = (block >> 8) & 0xff;
		tf->lbal = block & 0xff;

		tf->device = ATA_LBA;
		if (tf->flags & ATA_TFLAG_FUA)
			tf->device |= 1 << 7;

		if (dev->flags & ATA_DFLAG_NCQ_PRIO_ENABLED &&
		    class == IOPRIO_CLASS_RT)
			tf->hob_nsect |= ATA_PRIO_HIGH << ATA_SHIFT_PRIO;

		if ((dev->flags & ATA_DFLAG_CDL_ENABLED) && cdl)
			ata_set_tf_cdl(qc, cdl);

	} else if (dev->flags & ATA_DFLAG_LBA) {
		tf->flags |= ATA_TFLAG_LBA;

		if ((dev->flags & ATA_DFLAG_CDL_ENABLED) && cdl)
			ata_set_tf_cdl(qc, cdl);

		/* Both FUA writes and a CDL index require 48-bit commands */
		if (!(tf->flags & ATA_TFLAG_FUA) &&
		    !(qc->flags & ATA_QCFLAG_HAS_CDL) &&
		    lba_28_ok(block, n_block)) {
			/* use LBA28 */
			tf->device |= (block >> 24) & 0xf;
		} else if (lba_48_ok(block, n_block)) {
			if (!(dev->flags & ATA_DFLAG_LBA48))
				return -ERANGE;

			/* use LBA48 */
			tf->flags |= ATA_TFLAG_LBA48;

			tf->hob_nsect = (n_block >> 8) & 0xff;

			tf->hob_lbah = (block >> 40) & 0xff;
			tf->hob_lbam = (block >> 32) & 0xff;
			tf->hob_lbal = (block >> 24) & 0xff;
		} else {
			/* request too large even for LBA48 */
			return -ERANGE;
		}

		if (unlikely(!ata_set_rwcmd_protocol(dev, tf)))
			return -EINVAL;

		tf->nsect = n_block & 0xff;

		tf->lbah = (block >> 16) & 0xff;
		tf->lbam = (block >> 8) & 0xff;
		tf->lbal = block & 0xff;

		tf->device |= ATA_LBA;
	} else {
		/* CHS */
		u32 sect, head, cyl, track;

		/* The request -may- be too large for CHS addressing. */
		if (!lba_28_ok(block, n_block))
			return -ERANGE;

		if (unlikely(!ata_set_rwcmd_protocol(dev, tf)))
			return -EINVAL;

		/* Convert LBA to CHS */
		track = (u32)block / dev->sectors;
		cyl   = track / dev->heads;
		head  = track % dev->heads;
		sect  = (u32)block % dev->sectors + 1;

		/* Check whether the converted CHS can fit.
		   Cylinder: 0-65535
		   Head: 0-15
		   Sector: 1-255*/
		if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect))
			return -ERANGE;

		tf->nsect = n_block & 0xff; /* Sector count 0 means 256 sectors */
		tf->lbal = sect;
		tf->lbam = cyl;
		tf->lbah = cyl >> 8;
		tf->device |= head;
	}

	return 0;
}

/**
 *	ata_pack_xfermask - Pack pio, mwdma and udma masks into xfer_mask
 *	@pio_mask: pio_mask
 *	@mwdma_mask: mwdma_mask
 *	@udma_mask: udma_mask
 *
 *	Pack @pio_mask, @mwdma_mask and @udma_mask into a single
 *	unsigned int xfer_mask.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Packed xfer_mask.
 */
unsigned int ata_pack_xfermask(unsigned int pio_mask,
			       unsigned int mwdma_mask,
			       unsigned int udma_mask)
{
	return	((pio_mask << ATA_SHIFT_PIO) & ATA_MASK_PIO) |
		((mwdma_mask << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA) |
		((udma_mask << ATA_SHIFT_UDMA) & ATA_MASK_UDMA);
}
EXPORT_SYMBOL_GPL(ata_pack_xfermask);

/**
 *	ata_unpack_xfermask - Unpack xfer_mask into pio, mwdma and udma masks
 *	@xfer_mask: xfer_mask to unpack
 *	@pio_mask: resulting pio_mask
 *	@mwdma_mask: resulting mwdma_mask
 *	@udma_mask: resulting udma_mask
 *
 *	Unpack @xfer_mask into @pio_mask, @mwdma_mask and @udma_mask.
 *	Any NULL destination masks will be ignored.
 */
void ata_unpack_xfermask(unsigned int xfer_mask, unsigned int *pio_mask,
			 unsigned int *mwdma_mask, unsigned int *udma_mask)
{
	if (pio_mask)
		*pio_mask = (xfer_mask & ATA_MASK_PIO) >> ATA_SHIFT_PIO;
	if (mwdma_mask)
		*mwdma_mask = (xfer_mask & ATA_MASK_MWDMA) >> ATA_SHIFT_MWDMA;
	if (udma_mask)
		*udma_mask = (xfer_mask & ATA_MASK_UDMA) >> ATA_SHIFT_UDMA;
}

static const struct ata_xfer_ent {
	int shift, bits;
	u8 base;
} ata_xfer_tbl[] = {
	{ ATA_SHIFT_PIO, ATA_NR_PIO_MODES, XFER_PIO_0 },
	{ ATA_SHIFT_MWDMA, ATA_NR_MWDMA_MODES, XFER_MW_DMA_0 },
	{ ATA_SHIFT_UDMA, ATA_NR_UDMA_MODES, XFER_UDMA_0 },
	{ -1, },
};

/**
 *	ata_xfer_mask2mode - Find matching XFER_* for the given xfer_mask
 *	@xfer_mask: xfer_mask of interest
 *
 *	Return matching XFER_* value for @xfer_mask.  Only the highest
 *	bit of @xfer_mask is considered.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Matching XFER_* value, 0xff if no match found.
 */
u8 ata_xfer_mask2mode(unsigned int xfer_mask)
{
	int highbit = fls(xfer_mask) - 1;
	const struct ata_xfer_ent *ent;

	for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
		if (highbit >= ent->shift && highbit < ent->shift + ent->bits)
			return ent->base + highbit - ent->shift;
	return 0xff;
}
EXPORT_SYMBOL_GPL(ata_xfer_mask2mode);

/**
 *	ata_xfer_mode2mask - Find matching xfer_mask for XFER_*
 *	@xfer_mode: XFER_* of interest
 *
 *	Return matching xfer_mask for @xfer_mode.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Matching xfer_mask, 0 if no match found.
 */
unsigned int ata_xfer_mode2mask(u8 xfer_mode)
{
	const struct ata_xfer_ent *ent;

	for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
		if (xfer_mode >= ent->base && xfer_mode < ent->base + ent->bits)
			return ((2 << (ent->shift + xfer_mode - ent->base)) - 1)
				& ~((1 << ent->shift) - 1);
	return 0;
}
EXPORT_SYMBOL_GPL(ata_xfer_mode2mask);

/**
 *	ata_xfer_mode2shift - Find matching xfer_shift for XFER_*
 *	@xfer_mode: XFER_* of interest
 *
 *	Return matching xfer_shift for @xfer_mode.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Matching xfer_shift, -1 if no match found.
 */
int ata_xfer_mode2shift(u8 xfer_mode)
{
	const struct ata_xfer_ent *ent;

	for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
		if (xfer_mode >= ent->base && xfer_mode < ent->base + ent->bits)
			return ent->shift;
	return -1;
}
EXPORT_SYMBOL_GPL(ata_xfer_mode2shift);

/**
 *	ata_mode_string - convert xfer_mask to string
 *	@xfer_mask: mask of bits supported; only highest bit counts.
 *
 *	Determine string which represents the highest speed
 *	(highest bit in @modemask).
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Constant C string representing highest speed listed in
 *	@mode_mask, or the constant C string "<n/a>".
 */
const char *ata_mode_string(unsigned int xfer_mask)
{
	static const char * const xfer_mode_str[] = {
		"PIO0",
		"PIO1",
		"PIO2",
		"PIO3",
		"PIO4",
		"PIO5",
		"PIO6",
		"MWDMA0",
		"MWDMA1",
		"MWDMA2",
		"MWDMA3",
		"MWDMA4",
		"UDMA/16",
		"UDMA/25",
		"UDMA/33",
		"UDMA/44",
		"UDMA/66",
		"UDMA/100",
		"UDMA/133",
		"UDMA7",
	};
	int highbit;

	highbit = fls(xfer_mask) - 1;
	if (highbit >= 0 && highbit < ARRAY_SIZE(xfer_mode_str))
		return xfer_mode_str[highbit];
	return "<n/a>";
}
EXPORT_SYMBOL_GPL(ata_mode_string);

const char *sata_spd_string(unsigned int spd)
{
	static const char * const spd_str[] = {
		"1.5 Gbps",
		"3.0 Gbps",
		"6.0 Gbps",
	};

	if (spd == 0 || (spd - 1) >= ARRAY_SIZE(spd_str))
		return "<unknown>";
	return spd_str[spd - 1];
}

/**
 *	ata_dev_classify - determine device type based on ATA-spec signature
 *	@tf: ATA taskfile register set for device to be identified
 *
 *	Determine from taskfile register contents whether a device is
 *	ATA or ATAPI, as per "Signature and persistence" section
 *	of ATA/PI spec (volume 1, sect 5.14).
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, %ATA_DEV_PMP,
 *	%ATA_DEV_ZAC, or %ATA_DEV_UNKNOWN the event of failure.
 */
unsigned int ata_dev_classify(const struct ata_taskfile *tf)
{
	/* Apple's open source Darwin code hints that some devices only
	 * put a proper signature into the LBA mid/high registers,
	 * So, we only check those.  It's sufficient for uniqueness.
	 *
	 * ATA/ATAPI-7 (d1532v1r1: Feb. 19, 2003) specified separate
	 * signatures for ATA and ATAPI devices attached on SerialATA,
	 * 0x3c/0xc3 and 0x69/0x96 respectively.  However, SerialATA
	 * spec has never mentioned about using different signatures
	 * for ATA/ATAPI devices.  Then, Serial ATA II: Port
	 * Multiplier specification began to use 0x69/0x96 to identify
	 * port multpliers and 0x3c/0xc3 to identify SEMB device.
	 * ATA/ATAPI-7 dropped descriptions about 0x3c/0xc3 and
	 * 0x69/0x96 shortly and described them as reserved for
	 * SerialATA.
	 *
	 * We follow the current spec and consider that 0x69/0x96
	 * identifies a port multiplier and 0x3c/0xc3 a SEMB device.
	 * Unfortunately, WDC WD1600JS-62MHB5 (a hard drive) reports
	 * SEMB signature.  This is worked around in
	 * ata_dev_read_id().
	 */
	if (tf->lbam == 0 && tf->lbah == 0)
		return ATA_DEV_ATA;

	if (tf->lbam == 0x14 && tf->lbah == 0xeb)
		return ATA_DEV_ATAPI;

	if (tf->lbam == 0x69 && tf->lbah == 0x96)
		return ATA_DEV_PMP;

	if (tf->lbam == 0x3c && tf->lbah == 0xc3)
		return ATA_DEV_SEMB;

	if (tf->lbam == 0xcd && tf->lbah == 0xab)
		return ATA_DEV_ZAC;

	return ATA_DEV_UNKNOWN;
}
EXPORT_SYMBOL_GPL(ata_dev_classify);

/**
 *	ata_id_string - Convert IDENTIFY DEVICE page into string
 *	@id: IDENTIFY DEVICE results we will examine
 *	@s: string into which data is output
 *	@ofs: offset into identify device page
 *	@len: length of string to return. must be an even number.
 *
 *	The strings in the IDENTIFY DEVICE page are broken up into
 *	16-bit chunks.  Run through the string, and output each
 *	8-bit chunk linearly, regardless of platform.
 *
 *	LOCKING:
 *	caller.
 */

void ata_id_string(const u16 *id, unsigned char *s,
		   unsigned int ofs, unsigned int len)
{
	unsigned int c;

	BUG_ON(len & 1);

	while (len > 0) {
		c = id[ofs] >> 8;
		*s = c;
		s++;

		c = id[ofs] & 0xff;
		*s = c;
		s++;

		ofs++;
		len -= 2;
	}
}
EXPORT_SYMBOL_GPL(ata_id_string);

/**
 *	ata_id_c_string - Convert IDENTIFY DEVICE page into C string
 *	@id: IDENTIFY DEVICE results we will examine
 *	@s: string into which data is output
 *	@ofs: offset into identify device page
 *	@len: length of string to return. must be an odd number.
 *
 *	This function is identical to ata_id_string except that it
 *	trims trailing spaces and terminates the resulting string with
 *	null.  @len must be actual maximum length (even number) + 1.
 *
 *	LOCKING:
 *	caller.
 */
void ata_id_c_string(const u16 *id, unsigned char *s,
		     unsigned int ofs, unsigned int len)
{
	unsigned char *p;

	ata_id_string(id, s, ofs, len - 1);

	p = s + strnlen(s, len - 1);
	while (p > s && p[-1] == ' ')
		p--;
	*p = '\0';
}
EXPORT_SYMBOL_GPL(ata_id_c_string);

static u64 ata_id_n_sectors(const u16 *id)
{
	if (ata_id_has_lba(id)) {
		if (ata_id_has_lba48(id))
			return ata_id_u64(id, ATA_ID_LBA_CAPACITY_2);

		return ata_id_u32(id, ATA_ID_LBA_CAPACITY);
	}

	if (ata_id_current_chs_valid(id))
		return (u32)id[ATA_ID_CUR_CYLS] * (u32)id[ATA_ID_CUR_HEADS] *
		       (u32)id[ATA_ID_CUR_SECTORS];

	return (u32)id[ATA_ID_CYLS] * (u32)id[ATA_ID_HEADS] *
	       (u32)id[ATA_ID_SECTORS];
}

u64 ata_tf_to_lba48(const struct ata_taskfile *tf)
{
	u64 sectors = 0;

	sectors |= ((u64)(tf->hob_lbah & 0xff)) << 40;
	sectors |= ((u64)(tf->hob_lbam & 0xff)) << 32;
	sectors |= ((u64)(tf->hob_lbal & 0xff)) << 24;
	sectors |= (tf->lbah & 0xff) << 16;
	sectors |= (tf->lbam & 0xff) << 8;
	sectors |= (tf->lbal & 0xff);

	return sectors;
}

u64 ata_tf_to_lba(const struct ata_taskfile *tf)
{
	u64 sectors = 0;

	sectors |= (tf->device & 0x0f) << 24;
	sectors |= (tf->lbah & 0xff) << 16;
	sectors |= (tf->lbam & 0xff) << 8;
	sectors |= (tf->lbal & 0xff);

	return sectors;
}

/**
 *	ata_read_native_max_address - Read native max address
 *	@dev: target device
 *	@max_sectors: out parameter for the result native max address
 *
 *	Perform an LBA48 or LBA28 native size query upon the device in
 *	question.
 *
 *	RETURNS:
 *	0 on success, -EACCES if command is aborted by the drive.
 *	-EIO on other errors.
 */
static int ata_read_native_max_address(struct ata_device *dev, u64 *max_sectors)
{
	unsigned int err_mask;
	struct ata_taskfile tf;
	int lba48 = ata_id_has_lba48(dev->id);

	ata_tf_init(dev, &tf);

	/* always clear all address registers */
	tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;

	if (lba48) {
		tf.command = ATA_CMD_READ_NATIVE_MAX_EXT;
		tf.flags |= ATA_TFLAG_LBA48;
	} else
		tf.command = ATA_CMD_READ_NATIVE_MAX;

	tf.protocol = ATA_PROT_NODATA;
	tf.device |= ATA_LBA;

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	if (err_mask) {
		ata_dev_warn(dev,
			     "failed to read native max address (err_mask=0x%x)\n",
			     err_mask);
		if (err_mask == AC_ERR_DEV && (tf.error & ATA_ABORTED))
			return -EACCES;
		return -EIO;
	}

	if (lba48)
		*max_sectors = ata_tf_to_lba48(&tf) + 1;
	else
		*max_sectors = ata_tf_to_lba(&tf) + 1;
	if (dev->quirks & ATA_QUIRK_HPA_SIZE)
		(*max_sectors)--;
	return 0;
}

/**
 *	ata_set_max_sectors - Set max sectors
 *	@dev: target device
 *	@new_sectors: new max sectors value to set for the device
 *
 *	Set max sectors of @dev to @new_sectors.
 *
 *	RETURNS:
 *	0 on success, -EACCES if command is aborted or denied (due to
 *	previous non-volatile SET_MAX) by the drive.  -EIO on other
 *	errors.
 */
static int ata_set_max_sectors(struct ata_device *dev, u64 new_sectors)
{
	unsigned int err_mask;
	struct ata_taskfile tf;
	int lba48 = ata_id_has_lba48(dev->id);

	new_sectors--;

	ata_tf_init(dev, &tf);

	tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;

	if (lba48) {
		tf.command = ATA_CMD_SET_MAX_EXT;
		tf.flags |= ATA_TFLAG_LBA48;

		tf.hob_lbal = (new_sectors >> 24) & 0xff;
		tf.hob_lbam = (new_sectors >> 32) & 0xff;
		tf.hob_lbah = (new_sectors >> 40) & 0xff;
	} else {
		tf.command = ATA_CMD_SET_MAX;

		tf.device |= (new_sectors >> 24) & 0xf;
	}

	tf.protocol = ATA_PROT_NODATA;
	tf.device |= ATA_LBA;

	tf.lbal = (new_sectors >> 0) & 0xff;
	tf.lbam = (new_sectors >> 8) & 0xff;
	tf.lbah = (new_sectors >> 16) & 0xff;

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	if (err_mask) {
		ata_dev_warn(dev,
			     "failed to set max address (err_mask=0x%x)\n",
			     err_mask);
		if (err_mask == AC_ERR_DEV &&
		    (tf.error & (ATA_ABORTED | ATA_IDNF)))
			return -EACCES;
		return -EIO;
	}

	return 0;
}

/**
 *	ata_hpa_resize		-	Resize a device with an HPA set
 *	@dev: Device to resize
 *
 *	Read the size of an LBA28 or LBA48 disk with HPA features and resize
 *	it if required to the full size of the media. The caller must check
 *	the drive has the HPA feature set enabled.
 *
 *	RETURNS:
 *	0 on success, -errno on failure.
 */
static int ata_hpa_resize(struct ata_device *dev)
{
	bool print_info = ata_dev_print_info(dev);
	bool unlock_hpa = ata_ignore_hpa || dev->flags & ATA_DFLAG_UNLOCK_HPA;
	u64 sectors = ata_id_n_sectors(dev->id);
	u64 native_sectors;
	int rc;

	/* do we need to do it? */
	if ((dev->class != ATA_DEV_ATA && dev->class != ATA_DEV_ZAC) ||
	    !ata_id_has_lba(dev->id) || !ata_id_hpa_enabled(dev->id) ||
	    (dev->quirks & ATA_QUIRK_BROKEN_HPA) || ata_id_is_locked(dev->id))
		return 0;

	/* read native max address */
	rc = ata_read_native_max_address(dev, &native_sectors);
	if (rc) {
		/* If device aborted the command or HPA isn't going to
		 * be unlocked, skip HPA resizing.
		 */
		if (rc == -EACCES || !unlock_hpa) {
			ata_dev_warn(dev,
				     "HPA support seems broken, skipping HPA handling\n");
			dev->quirks |= ATA_QUIRK_BROKEN_HPA;

			/* we can continue if device aborted the command */
			if (rc == -EACCES)
				rc = 0;
		}

		return rc;
	}
	dev->n_native_sectors = native_sectors;

	/* nothing to do? */
	if (native_sectors <= sectors || !unlock_hpa) {
		if (!print_info || native_sectors == sectors)
			return 0;

		if (native_sectors > sectors)
			ata_dev_info(dev,
				"HPA detected: current %llu, native %llu\n",
				(unsigned long long)sectors,
				(unsigned long long)native_sectors);
		else if (native_sectors < sectors)
			ata_dev_warn(dev,
				"native sectors (%llu) is smaller than sectors (%llu)\n",
				(unsigned long long)native_sectors,
				(unsigned long long)sectors);
		return 0;
	}

	/* let's unlock HPA */
	rc = ata_set_max_sectors(dev, native_sectors);
	if (rc == -EACCES) {
		/* if device aborted the command, skip HPA resizing */
		ata_dev_warn(dev,
			     "device aborted resize (%llu -> %llu), skipping HPA handling\n",
			     (unsigned long long)sectors,
			     (unsigned long long)native_sectors);
		dev->quirks |= ATA_QUIRK_BROKEN_HPA;
		return 0;
	} else if (rc)
		return rc;

	/* re-read IDENTIFY data */
	rc = ata_dev_reread_id(dev, 0);
	if (rc) {
		ata_dev_err(dev,
			    "failed to re-read IDENTIFY data after HPA resizing\n");
		return rc;
	}

	if (print_info) {
		u64 new_sectors = ata_id_n_sectors(dev->id);
		ata_dev_info(dev,
			"HPA unlocked: %llu -> %llu, native %llu\n",
			(unsigned long long)sectors,
			(unsigned long long)new_sectors,
			(unsigned long long)native_sectors);
	}

	return 0;
}

/**
 *	ata_dump_id - IDENTIFY DEVICE info debugging output
 *	@dev: device from which the information is fetched
 *	@id: IDENTIFY DEVICE page to dump
 *
 *	Dump selected 16-bit words from the given IDENTIFY DEVICE
 *	page.
 *
 *	LOCKING:
 *	caller.
 */

static inline void ata_dump_id(struct ata_device *dev, const u16 *id)
{
	ata_dev_dbg(dev,
		"49==0x%04x  53==0x%04x  63==0x%04x  64==0x%04x  75==0x%04x\n"
		"80==0x%04x  81==0x%04x  82==0x%04x  83==0x%04x  84==0x%04x\n"
		"88==0x%04x  93==0x%04x\n",
		id[49], id[53], id[63], id[64], id[75], id[80],
		id[81], id[82], id[83], id[84], id[88], id[93]);
}

/**
 *	ata_id_xfermask - Compute xfermask from the given IDENTIFY data
 *	@id: IDENTIFY data to compute xfer mask from
 *
 *	Compute the xfermask for this device. This is not as trivial
 *	as it seems if we must consider early devices correctly.
 *
 *	FIXME: pre IDE drive timing (do we care ?).
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Computed xfermask
 */
unsigned int ata_id_xfermask(const u16 *id)
{
	unsigned int pio_mask, mwdma_mask, udma_mask;

	/* Usual case. Word 53 indicates word 64 is valid */
	if (id[ATA_ID_FIELD_VALID] & (1 << 1)) {
		pio_mask = id[ATA_ID_PIO_MODES] & 0x03;
		pio_mask <<= 3;
		pio_mask |= 0x7;
	} else {
		/* If word 64 isn't valid then Word 51 high byte holds
		 * the PIO timing number for the maximum. Turn it into
		 * a mask.
		 */
		u8 mode = (id[ATA_ID_OLD_PIO_MODES] >> 8) & 0xFF;
		if (mode < 5)	/* Valid PIO range */
			pio_mask = (2 << mode) - 1;
		else
			pio_mask = 1;

		/* But wait.. there's more. Design your standards by
		 * committee and you too can get a free iordy field to
		 * process. However it is the speeds not the modes that
		 * are supported... Note drivers using the timing API
		 * will get this right anyway
		 */
	}

	mwdma_mask = id[ATA_ID_MWDMA_MODES] & 0x07;

	if (ata_id_is_cfa(id)) {
		/*
		 *	Process compact flash extended modes
		 */
		int pio = (id[ATA_ID_CFA_MODES] >> 0) & 0x7;
		int dma = (id[ATA_ID_CFA_MODES] >> 3) & 0x7;

		if (pio)
			pio_mask |= (1 << 5);
		if (pio > 1)
			pio_mask |= (1 << 6);
		if (dma)
			mwdma_mask |= (1 << 3);
		if (dma > 1)
			mwdma_mask |= (1 << 4);
	}

	udma_mask = 0;
	if (id[ATA_ID_FIELD_VALID] & (1 << 2))
		udma_mask = id[ATA_ID_UDMA_MODES] & 0xff;

	return ata_pack_xfermask(pio_mask, mwdma_mask, udma_mask);
}
EXPORT_SYMBOL_GPL(ata_id_xfermask);

static void ata_qc_complete_internal(struct ata_queued_cmd *qc)
{
	struct completion *waiting = qc->private_data;

	complete(waiting);
}

/**
 *	ata_exec_internal - execute libata internal command
 *	@dev: Device to which the command is sent
 *	@tf: Taskfile registers for the command and the result
 *	@cdb: CDB for packet command
 *	@dma_dir: Data transfer direction of the command
 *	@buf: Data buffer of the command
 *	@buflen: Length of data buffer
 *	@timeout: Timeout in msecs (0 for default)
 *
 *	Executes libata internal command with timeout. @tf contains
 *	the command on entry and the result on return. Timeout and error
 *	conditions are reported via the return value. No recovery action
 *	is taken after a command times out. It is the caller's duty to
 *	clean up after timeout.
 *
 *	LOCKING:
 *	None.  Should be called with kernel context, might sleep.
 *
 *	RETURNS:
 *	Zero on success, AC_ERR_* mask on failure
 */
unsigned int ata_exec_internal(struct ata_device *dev, struct ata_taskfile *tf,
			       const u8 *cdb, enum dma_data_direction dma_dir,
			       void *buf, unsigned int buflen,
			       unsigned int timeout)
{
	struct ata_link *link = dev->link;
	struct ata_port *ap = link->ap;
	const bool owns_eh_mutex = ap->host->eh_owner == current;
	u8 command = tf->command;
	struct ata_queued_cmd *qc;
	struct scatterlist sgl;
	unsigned int preempted_tag;
	u32 preempted_sactive;
	u64 preempted_qc_active;
	int preempted_nr_active_links;
	bool auto_timeout = false;
	DECLARE_COMPLETION_ONSTACK(wait);
	unsigned long flags;
	unsigned int err_mask;
	int rc;

	if (WARN_ON(dma_dir != DMA_NONE && !buf))
		return AC_ERR_INVALID;

	spin_lock_irqsave(ap->lock, flags);

	/* No internal command while frozen */
	if (ata_port_is_frozen(ap)) {
		spin_unlock_irqrestore(ap->lock, flags);
		return AC_ERR_SYSTEM;
	}

	/* Initialize internal qc */
	qc = __ata_qc_from_tag(ap, ATA_TAG_INTERNAL);

	qc->tag = ATA_TAG_INTERNAL;
	qc->hw_tag = 0;
	qc->scsicmd = NULL;
	qc->ap = ap;
	qc->dev = dev;
	ata_qc_reinit(qc);

	preempted_tag = link->active_tag;
	preempted_sactive = link->sactive;
	preempted_qc_active = ap->qc_active;
	preempted_nr_active_links = ap->nr_active_links;
	link->active_tag = ATA_TAG_POISON;
	link->sactive = 0;
	ap->qc_active = 0;
	ap->nr_active_links = 0;

	/* Prepare and issue qc */
	qc->tf = *tf;
	if (cdb)
		memcpy(qc->cdb, cdb, ATAPI_CDB_LEN);

	/* Some SATA bridges need us to indicate data xfer direction */
	if (tf->protocol == ATAPI_PROT_DMA && (dev->flags & ATA_DFLAG_DMADIR) &&
	    dma_dir == DMA_FROM_DEVICE)
		qc->tf.feature |= ATAPI_DMADIR;

	qc->flags |= ATA_QCFLAG_RESULT_TF;
	qc->dma_dir = dma_dir;
	if (dma_dir != DMA_NONE) {
		sg_init_one(&sgl, buf, buflen);
		ata_sg_init(qc, &sgl, 1);
		qc->nbytes = buflen;
	}

	qc->private_data = &wait;
	qc->complete_fn = ata_qc_complete_internal;

	ata_qc_issue(ap, qc);

	spin_unlock_irqrestore(ap->lock, flags);

	if (!timeout) {
		if (ata_probe_timeout) {
			timeout = ata_probe_timeout * 1000;
		} else {
			timeout = ata_internal_cmd_timeout(dev, command);
			auto_timeout = true;
		}
	}

	if (owns_eh_mutex) {
		/*
		 * To prevent that the compiler complains about the
		 * ata_eh_release() call below.
		 */
		__acquire(&ap->host->eh_mutex);
		ata_eh_release(ap);
	}

	rc = wait_for_completion_timeout(&wait, msecs_to_jiffies(timeout));

	if (owns_eh_mutex) {
		ata_eh_acquire(ap);
		/*
		 * To prevent that the compiler complains about the above
		 * ata_eh_acquire() call.
		 */
		__release(&ap->host->eh_mutex);
	}

	ata_sff_flush_pio_task(ap);

	if (!rc) {
		/*
		 * We are racing with irq here. If we lose, the following test
		 * prevents us from completing the qc twice. If we win, the port
		 * is frozen and will be cleaned up by ->post_internal_cmd().
		 */
		spin_lock_irqsave(ap->lock, flags);
		if (qc->flags & ATA_QCFLAG_ACTIVE) {
			qc->err_mask |= AC_ERR_TIMEOUT;
			ata_port_freeze(ap);
			ata_dev_warn(dev, "qc timeout after %u msecs (cmd 0x%x)\n",
				     timeout, command);
		}
		spin_unlock_irqrestore(ap->lock, flags);
	}

	if (ap->ops->post_internal_cmd)
		ap->ops->post_internal_cmd(qc);

	/* Perform minimal error analysis */
	if (qc->flags & ATA_QCFLAG_EH) {
		if (qc->result_tf.status & (ATA_ERR | ATA_DF))
			qc->err_mask |= AC_ERR_DEV;

		if (!qc->err_mask)
			qc->err_mask |= AC_ERR_OTHER;

		if (qc->err_mask & ~AC_ERR_OTHER)
			qc->err_mask &= ~AC_ERR_OTHER;
	} else if (qc->tf.command == ATA_CMD_REQ_SENSE_DATA) {
		qc->result_tf.status |= ATA_SENSE;
	}

	/* Finish up */
	spin_lock_irqsave(ap->lock, flags);

	*tf = qc->result_tf;
	err_mask = qc->err_mask;

	ata_qc_free(qc);
	link->active_tag = preempted_tag;
	link->sactive = preempted_sactive;
	ap->qc_active = preempted_qc_active;
	ap->nr_active_links = preempted_nr_active_links;

	spin_unlock_irqrestore(ap->lock, flags);

	if ((err_mask & AC_ERR_TIMEOUT) && auto_timeout)
		ata_internal_cmd_timed_out(dev, command);

	return err_mask;
}

/**
 *	ata_pio_need_iordy	-	check if iordy needed
 *	@adev: ATA device
 *
 *	Check if the current speed of the device requires IORDY. Used
 *	by various controllers for chip configuration.
 */
unsigned int ata_pio_need_iordy(const struct ata_device *adev)
{
	/* Don't set IORDY if we're preparing for reset.  IORDY may
	 * lead to controller lock up on certain controllers if the
	 * port is not occupied.  See bko#11703 for details.
	 */
	if (adev->link->ap->pflags & ATA_PFLAG_RESETTING)
		return 0;
	/* Controller doesn't support IORDY.  Probably a pointless
	 * check as the caller should know this.
	 */
	if (adev->link->ap->flags & ATA_FLAG_NO_IORDY)
		return 0;
	/* CF spec. r4.1 Table 22 says no iordy on PIO5 and PIO6.  */
	if (ata_id_is_cfa(adev->id)
	    && (adev->pio_mode == XFER_PIO_5 || adev->pio_mode == XFER_PIO_6))
		return 0;
	/* PIO3 and higher it is mandatory */
	if (adev->pio_mode > XFER_PIO_2)
		return 1;
	/* We turn it on when possible */
	if (ata_id_has_iordy(adev->id))
		return 1;
	return 0;
}
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);

/**
 *	ata_pio_mask_no_iordy	-	Return the non IORDY mask
 *	@adev: ATA device
 *
 *	Compute the highest mode possible if we are not using iordy. Return
 *	-1 if no iordy mode is available.
 */
static u32 ata_pio_mask_no_iordy(const struct ata_device *adev)
{
	/* If we have no drive specific rule, then PIO 2 is non IORDY */
	if (adev->id[ATA_ID_FIELD_VALID] & 2) {	/* EIDE */
		u16 pio = adev->id[ATA_ID_EIDE_PIO];
		/* Is the speed faster than the drive allows non IORDY ? */
		if (pio) {
			/* This is cycle times not frequency - watch the logic! */
			if (pio > 240)	/* PIO2 is 240nS per cycle */
				return 3 << ATA_SHIFT_PIO;
			return 7 << ATA_SHIFT_PIO;
		}
	}
	return 3 << ATA_SHIFT_PIO;
}

/**
 *	ata_do_dev_read_id		-	default ID read method
 *	@dev: device
 *	@tf: proposed taskfile
 *	@id: data buffer
 *
 *	Issue the identify taskfile and hand back the buffer containing
 *	identify data. For some RAID controllers and for pre ATA devices
 *	this function is wrapped or replaced by the driver
 */
unsigned int ata_do_dev_read_id(struct ata_device *dev,
				struct ata_taskfile *tf, __le16 *id)
{
	return ata_exec_internal(dev, tf, NULL, DMA_FROM_DEVICE,
				     id, sizeof(id[0]) * ATA_ID_WORDS, 0);
}
EXPORT_SYMBOL_GPL(ata_do_dev_read_id);

/**
 *	ata_dev_read_id - Read ID data from the specified device
 *	@dev: target device
 *	@p_class: pointer to class of the target device (may be changed)
 *	@flags: ATA_READID_* flags
 *	@id: buffer to read IDENTIFY data into
 *
 *	Read ID data from the specified device.  ATA_CMD_ID_ATA is
 *	performed on ATA devices and ATA_CMD_ID_ATAPI on ATAPI
 *	devices.  This function also issues ATA_CMD_INIT_DEV_PARAMS
 *	for pre-ATA4 drives.
 *
 *	FIXME: ATA_CMD_ID_ATA is optional for early drives and right
 *	now we abort if we hit that case.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	0 on success, -errno otherwise.
 */
int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
		    unsigned int flags, u16 *id)
{
	struct ata_port *ap = dev->link->ap;
	unsigned int class = *p_class;
	struct ata_taskfile tf;
	unsigned int err_mask = 0;
	const char *reason;
	bool is_semb = class == ATA_DEV_SEMB;
	int may_fallback = 1, tried_spinup = 0;
	int rc;

retry:
	ata_tf_init(dev, &tf);

	switch (class) {
	case ATA_DEV_SEMB:
		class = ATA_DEV_ATA;	/* some hard drives report SEMB sig */
		fallthrough;
	case ATA_DEV_ATA:
	case ATA_DEV_ZAC:
		tf.command = ATA_CMD_ID_ATA;
		break;
	case ATA_DEV_ATAPI:
		tf.command = ATA_CMD_ID_ATAPI;
		break;
	default:
		rc = -ENODEV;
		reason = "unsupported class";
		goto err_out;
	}

	tf.protocol = ATA_PROT_PIO;

	/* Some devices choke if TF registers contain garbage.  Make
	 * sure those are properly initialized.
	 */
	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;

	/* Device presence detection is unreliable on some
	 * controllers.  Always poll IDENTIFY if available.
	 */
	tf.flags |= ATA_TFLAG_POLLING;

	if (ap->ops->read_id)
		err_mask = ap->ops->read_id(dev, &tf, (__le16 *)id);
	else
		err_mask = ata_do_dev_read_id(dev, &tf, (__le16 *)id);

	if (err_mask) {
		if (err_mask & AC_ERR_NODEV_HINT) {
			ata_dev_dbg(dev, "NODEV after polling detection\n");
			return -ENOENT;
		}

		if (is_semb) {
			ata_dev_info(dev,
		     "IDENTIFY failed on device w/ SEMB sig, disabled\n");
			/* SEMB is not supported yet */
			*p_class = ATA_DEV_SEMB_UNSUP;
			return 0;
		}

		if ((err_mask == AC_ERR_DEV) && (tf.error & ATA_ABORTED)) {
			/* Device or controller might have reported
			 * the wrong device class.  Give a shot at the
			 * other IDENTIFY if the current one is
			 * aborted by the device.
			 */
			if (may_fallback) {
				may_fallback = 0;

				if (class == ATA_DEV_ATA)
					class = ATA_DEV_ATAPI;
				else
					class = ATA_DEV_ATA;
				goto retry;
			}

			/* Control reaches here iff the device aborted
			 * both flavors of IDENTIFYs which happens
			 * sometimes with phantom devices.
			 */
			ata_dev_dbg(dev,
				    "both IDENTIFYs aborted, assuming NODEV\n");
			return -ENOENT;
		}

		rc = -EIO;
		reason = "I/O error";
		goto err_out;
	}

	if (dev->quirks & ATA_QUIRK_DUMP_ID) {
		ata_dev_info(dev, "dumping IDENTIFY data, "
			    "class=%d may_fallback=%d tried_spinup=%d\n",
			    class, may_fallback, tried_spinup);
		print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET,
			       16, 2, id, ATA_ID_WORDS * sizeof(*id), true);
	}

	/* Falling back doesn't make sense if ID data was read
	 * successfully at least once.
	 */
	may_fallback = 0;

	swap_buf_le16(id, ATA_ID_WORDS);

	/* sanity check */
	rc = -EINVAL;
	reason = "device reports invalid type";

	if (class == ATA_DEV_ATA || class == ATA_DEV_ZAC) {
		if (!ata_id_is_ata(id) && !ata_id_is_cfa(id))
			goto err_out;
		if (ap->host->flags & ATA_HOST_IGNORE_ATA &&
							ata_id_is_ata(id)) {
			ata_dev_dbg(dev,
				"host indicates ignore ATA devices, ignored\n");
			return -ENOENT;
		}
	} else {
		if (ata_id_is_ata(id))
			goto err_out;
	}

	if (!tried_spinup && (id[2] == 0x37c8 || id[2] == 0x738c)) {
		tried_spinup = 1;
		/*
		 * Drive powered-up in standby mode, and requires a specific
		 * SET_FEATURES spin-up subcommand before it will accept
		 * anything other than the original IDENTIFY command.
		 */
		err_mask = ata_dev_set_feature(dev, SETFEATURES_SPINUP, 0);
		if (err_mask && id[2] != 0x738c) {
			rc = -EIO;
			reason = "SPINUP failed";
			goto err_out;
		}
		/*
		 * If the drive initially returned incomplete IDENTIFY info,
		 * we now must reissue the IDENTIFY command.
		 */
		if (id[2] == 0x37c8)
			goto retry;
	}

	if ((flags & ATA_READID_POSTRESET) &&
	    (class == ATA_DEV_ATA || class == ATA_DEV_ZAC)) {
		/*
		 * The exact sequence expected by certain pre-ATA4 drives is:
		 * SRST RESET
		 * IDENTIFY (optional in early ATA)
		 * INITIALIZE DEVICE PARAMETERS (later IDE and ATA)
		 * anything else..
		 * Some drives were very specific about that exact sequence.
		 *
		 * Note that ATA4 says lba is mandatory so the second check
		 * should never trigger.
		 */
		if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) {
			err_mask = ata_dev_init_params(dev, id[3], id[6]);
			if (err_mask) {
				rc = -EIO;
				reason = "INIT_DEV_PARAMS failed";
				goto err_out;
			}

			/* current CHS translation info (id[53-58]) might be
			 * changed. reread the identify device info.
			 */
			flags &= ~ATA_READID_POSTRESET;
			goto retry;
		}
	}

	*p_class = class;

	return 0;

 err_out:
	ata_dev_warn(dev, "failed to IDENTIFY (%s, err_mask=0x%x)\n",
		     reason, err_mask);
	return rc;
}

bool ata_dev_power_init_tf(struct ata_device *dev, struct ata_taskfile *tf,
			   bool set_active)
{
	/* Only applies to ATA and ZAC devices */
	if (dev->class != ATA_DEV_ATA && dev->class != ATA_DEV_ZAC)
		return false;

	ata_tf_init(dev, tf);
	tf->flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;
	tf->protocol = ATA_PROT_NODATA;

	if (set_active) {
		/* VERIFY for 1 sector at lba=0 */
		tf->command = ATA_CMD_VERIFY;
		tf->nsect = 1;
		if (dev->flags & ATA_DFLAG_LBA) {
			tf->flags |= ATA_TFLAG_LBA;
			tf->device |= ATA_LBA;
		} else {
			/* CHS */
			tf->lbal = 0x1; /* sect */
		}
	} else {
		tf->command = ATA_CMD_STANDBYNOW1;
	}

	return true;
}

static bool ata_dev_power_is_active(struct ata_device *dev)
{
	struct ata_taskfile tf;
	unsigned int err_mask;

	ata_tf_init(dev, &tf);
	tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;
	tf.protocol = ATA_PROT_NODATA;
	tf.command = ATA_CMD_CHK_POWER;

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	if (err_mask) {
		ata_dev_err(dev, "Check power mode failed (err_mask=0x%x)\n",
			    err_mask);
		/*
		 * Assume we are in standby mode so that we always force a
		 * spinup in ata_dev_power_set_active().
		 */
		return false;
	}

	ata_dev_dbg(dev, "Power mode: 0x%02x\n", tf.nsect);

	/* Active or idle */
	return tf.nsect == 0xff;
}

/**
 *	ata_dev_power_set_standby - Set a device power mode to standby
 *	@dev: target device
 *
 *	Issue a STANDBY IMMEDIATE command to set a device power mode to standby.
 *	For an HDD device, this spins down the disks.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 */
void ata_dev_power_set_standby(struct ata_device *dev)
{
	unsigned long ap_flags = dev->link->ap->flags;
	struct ata_taskfile tf;
	unsigned int err_mask;

	/* If the device is already sleeping or in standby, do nothing. */
	if ((dev->flags & ATA_DFLAG_SLEEPING) ||
	    !ata_dev_power_is_active(dev))
		return;

	/*
	 * Some odd clown BIOSes issue spindown on power off (ACPI S4 or S5)
	 * causing some drives to spin up and down again. For these, do nothing
	 * if we are being called on shutdown.
	 */
	if ((ap_flags & ATA_FLAG_NO_POWEROFF_SPINDOWN) &&
	    system_state == SYSTEM_POWER_OFF)
		return;

	if ((ap_flags & ATA_FLAG_NO_HIBERNATE_SPINDOWN) &&
	    system_entering_hibernation())
		return;

	/* Issue STANDBY IMMEDIATE command only if supported by the device */
	if (!ata_dev_power_init_tf(dev, &tf, false))
		return;

	ata_dev_notice(dev, "Entering standby power mode\n");

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	if (err_mask)
		ata_dev_err(dev, "STANDBY IMMEDIATE failed (err_mask=0x%x)\n",
			    err_mask);
}

/**
 *	ata_dev_power_set_active -  Set a device power mode to active
 *	@dev: target device
 *
 *	Issue a VERIFY command to enter to ensure that the device is in the
 *	active power mode. For a spun-down HDD (standby or idle power mode),
 *	the VERIFY command will complete after the disk spins up.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 */
void ata_dev_power_set_active(struct ata_device *dev)
{
	struct ata_taskfile tf;
	unsigned int err_mask;

	/*
	 * Issue READ VERIFY SECTORS command for 1 sector at lba=0 only
	 * if supported by the device.
	 */
	if (!ata_dev_power_init_tf(dev, &tf, true))
		return;

	/*
	 * Check the device power state & condition and force a spinup with
	 * VERIFY command only if the drive is not already ACTIVE or IDLE.
	 */
	if (ata_dev_power_is_active(dev))
		return;

	ata_dev_notice(dev, "Entering active power mode\n");

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	if (err_mask)
		ata_dev_err(dev, "VERIFY failed (err_mask=0x%x)\n",
			    err_mask);
}

/**
 *	ata_read_log_page - read a specific log page
 *	@dev: target device
 *	@log: log to read
 *	@page: page to read
 *	@buf: buffer to store read page
 *	@sectors: number of sectors to read
 *
 *	Read log page using READ_LOG_EXT command.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 *
 *	RETURNS:
 *	0 on success, AC_ERR_* mask otherwise.
 */
unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
			       u8 page, void *buf, unsigned int sectors)
{
	unsigned long ap_flags = dev->link->ap->flags;
	struct ata_taskfile tf;
	unsigned int err_mask;
	bool dma = false;

	ata_dev_dbg(dev, "read log page - log 0x%x, page 0x%x\n", log, page);

	/*
	 * Return error without actually issuing the command on controllers
	 * which e.g. lockup on a read log page.
	 */
	if (ap_flags & ATA_FLAG_NO_LOG_PAGE)
		return AC_ERR_DEV;

retry:
	ata_tf_init(dev, &tf);
	if (ata_dma_enabled(dev) && ata_id_has_read_log_dma_ext(dev->id) &&
	    !(dev->quirks & ATA_QUIRK_NO_DMA_LOG)) {
		tf.command = ATA_CMD_READ_LOG_DMA_EXT;
		tf.protocol = ATA_PROT_DMA;
		dma = true;
	} else {
		tf.command = ATA_CMD_READ_LOG_EXT;
		tf.protocol = ATA_PROT_PIO;
		dma = false;
	}
	tf.lbal = log;
	tf.lbam = page;
	tf.nsect = sectors;
	tf.hob_nsect = sectors >> 8;
	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_LBA48 | ATA_TFLAG_DEVICE;

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
				     buf, sectors * ATA_SECT_SIZE, 0);

	if (err_mask) {
		if (dma) {
			dev->quirks |= ATA_QUIRK_NO_DMA_LOG;
			if (!ata_port_is_frozen(dev->link->ap))
				goto retry;
		}
		ata_dev_err(dev,
			    "Read log 0x%02x page 0x%02x failed, Emask 0x%x\n",
			    (unsigned int)log, (unsigned int)page, err_mask);
	}

	return err_mask;
}

static inline void ata_clear_log_directory(struct ata_device *dev)
{
	memset(dev->gp_log_dir, 0, ATA_SECT_SIZE);
}

static int ata_read_log_directory(struct ata_device *dev)
{
	u16 version;

	/* If the log page is already cached, do nothing. */
	version = get_unaligned_le16(&dev->gp_log_dir[0]);
	if (version == 0x0001)
		return 0;

	if (ata_read_log_page(dev, ATA_LOG_DIRECTORY, 0, dev->gp_log_dir, 1)) {
		ata_clear_log_directory(dev);
		return -EIO;
	}

	version = get_unaligned_le16(&dev->gp_log_dir[0]);
	if (version != 0x0001)
		ata_dev_warn_once(dev,
				  "Invalid log directory version 0x%04x\n",
				  version);

	return 0;
}

static int ata_log_supported(struct ata_device *dev, u8 log)
{
	if (dev->quirks & ATA_QUIRK_NO_LOG_DIR)
		return 0;

	if (ata_read_log_directory(dev))
		return 0;

	return get_unaligned_le16(&dev->gp_log_dir[log * 2]);
}

static bool ata_identify_page_supported(struct ata_device *dev, u8 page)
{
	unsigned int err, i;

	if (dev->quirks & ATA_QUIRK_NO_ID_DEV_LOG)
		return false;

	if (!ata_log_supported(dev, ATA_LOG_IDENTIFY_DEVICE)) {
		/*
		 * IDENTIFY DEVICE data log is defined as mandatory starting
		 * with ACS-3 (ATA version 10). Warn about the missing log
		 * for drives which implement this ATA level or above.
		 */
		if (ata_id_major_version(dev->id) >= 10)
			ata_dev_warn(dev,
				"ATA Identify Device Log not supported\n");
		dev->quirks |= ATA_QUIRK_NO_ID_DEV_LOG;
		return false;
	}

	/*
	 * Read IDENTIFY DEVICE data log, page 0, to figure out if the page is
	 * supported.
	 */
	err = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE, 0,
				dev->sector_buf, 1);
	if (err)
		return false;

	for (i = 0; i < dev->sector_buf[8]; i++) {
		if (dev->sector_buf[9 + i] == page)
			return true;
	}

	return false;
}

static int ata_do_link_spd_quirk(struct ata_device *dev)
{
	struct ata_link *plink = ata_dev_phys_link(dev);
	u32 target, target_limit;

	if (!sata_scr_valid(plink))
		return 0;

	if (dev->quirks & ATA_QUIRK_1_5_GBPS)
		target = 1;
	else
		return 0;

	target_limit = (1 << target) - 1;

	/* if already on stricter limit, no need to push further */
	if (plink->sata_spd_limit <= target_limit)
		return 0;

	plink->sata_spd_limit = target_limit;

	/* Request another EH round by returning -EAGAIN if link is
	 * going faster than the target speed.  Forward progress is
	 * guaranteed by setting sata_spd_limit to target_limit above.
	 */
	if (plink->sata_spd > target) {
		ata_dev_info(dev, "applying link speed limit quirk to %s\n",
			     sata_spd_string(target));
		return -EAGAIN;
	}
	return 0;
}

static inline bool ata_dev_knobble(struct ata_device *dev)
{
	struct ata_port *ap = dev->link->ap;

	if (ata_dev_quirks(dev) & ATA_QUIRK_BRIDGE_OK)
		return false;

	return ((ap->cbl == ATA_CBL_SATA) && (!ata_id_is_sata(dev->id)));
}

static void ata_dev_config_ncq_send_recv(struct ata_device *dev)
{
	unsigned int err_mask;

	if (!ata_log_supported(dev, ATA_LOG_NCQ_SEND_RECV)) {
		ata_dev_warn(dev, "NCQ Send/Recv Log not supported\n");
		return;
	}
	err_mask = ata_read_log_page(dev, ATA_LOG_NCQ_SEND_RECV,
				     0, dev->sector_buf, 1);
	if (!err_mask) {
		u8 *cmds = dev->ncq_send_recv_cmds;

		dev->flags |= ATA_DFLAG_NCQ_SEND_RECV;
		memcpy(cmds, dev->sector_buf, ATA_LOG_NCQ_SEND_RECV_SIZE);

		if (dev->quirks & ATA_QUIRK_NO_NCQ_TRIM) {
			ata_dev_dbg(dev, "disabling queued TRIM support\n");
			cmds[ATA_LOG_NCQ_SEND_RECV_DSM_OFFSET] &=
				~ATA_LOG_NCQ_SEND_RECV_DSM_TRIM;
		}
	}
}

static void ata_dev_config_ncq_non_data(struct ata_device *dev)
{
	unsigned int err_mask;

	if (!ata_log_supported(dev, ATA_LOG_NCQ_NON_DATA)) {
		ata_dev_warn(dev,
			     "NCQ Non-Data Log not supported\n");
		return;
	}
	err_mask = ata_read_log_page(dev, ATA_LOG_NCQ_NON_DATA,
				     0, dev->sector_buf, 1);
	if (!err_mask)
		memcpy(dev->ncq_non_data_cmds, dev->sector_buf,
		       ATA_LOG_NCQ_NON_DATA_SIZE);
}

static void ata_dev_config_ncq_prio(struct ata_device *dev)
{
	unsigned int err_mask;

	if (!ata_identify_page_supported(dev, ATA_LOG_SATA_SETTINGS))
		return;

	err_mask = ata_read_log_page(dev,
				     ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_SATA_SETTINGS,
				     dev->sector_buf, 1);
	if (err_mask)
		goto not_supported;

	if (!(dev->sector_buf[ATA_LOG_NCQ_PRIO_OFFSET] & BIT(3)))
		goto not_supported;

	dev->flags |= ATA_DFLAG_NCQ_PRIO;

	return;

not_supported:
	dev->flags &= ~ATA_DFLAG_NCQ_PRIO_ENABLED;
	dev->flags &= ~ATA_DFLAG_NCQ_PRIO;
}

static bool ata_dev_check_adapter(struct ata_device *dev,
				  unsigned short vendor_id)
{
	struct pci_dev *pcidev = NULL;
	struct device *parent_dev = NULL;

	for (parent_dev = dev->tdev.parent; parent_dev != NULL;
	     parent_dev = parent_dev->parent) {
		if (dev_is_pci(parent_dev)) {
			pcidev = to_pci_dev(parent_dev);
			if (pcidev->vendor == vendor_id)
				return true;
			break;
		}
	}

	return false;
}

bool ata_adapter_is_online(struct ata_port *ap)
{
	struct device *dev;

	if (!ap || !ap->host)
		return false;

	dev = ap->host->dev;
	if (!dev)
		return false;

	if (dev_is_pci(dev) &&
	    pci_channel_offline(to_pci_dev(dev)))
		return false;

	return true;
}

static int ata_dev_config_ncq(struct ata_device *dev,
			       char *desc, size_t desc_sz)
{
	struct ata_port *ap = dev->link->ap;
	int hdepth = 0, ddepth = ata_id_queue_depth(dev->id);
	unsigned int err_mask;
	char *aa_desc = "";

	if (!ata_id_has_ncq(dev->id)) {
		desc[0] = '\0';
		return 0;
	}
	if (!IS_ENABLED(CONFIG_SATA_HOST))
		return 0;
	if (dev->quirks & ATA_QUIRK_NONCQ) {
		snprintf(desc, desc_sz, "NCQ (not used)");
		return 0;
	}

	if (dev->quirks & ATA_QUIRK_NO_NCQ_ON_ATI &&
	    ata_dev_check_adapter(dev, PCI_VENDOR_ID_ATI)) {
		snprintf(desc, desc_sz, "NCQ (not used)");
		return 0;
	}

	if (ap->flags & ATA_FLAG_NCQ) {
		hdepth = min(ap->scsi_host->can_queue, ATA_MAX_QUEUE);
		dev->flags |= ATA_DFLAG_NCQ;
	}

	if (!(dev->quirks & ATA_QUIRK_BROKEN_FPDMA_AA) &&
		(ap->flags & ATA_FLAG_FPDMA_AA) &&
		ata_id_has_fpdma_aa(dev->id)) {
		err_mask = ata_dev_set_feature(dev, SETFEATURES_SATA_ENABLE,
			SATA_FPDMA_AA);
		if (err_mask) {
			ata_dev_err(dev,
				    "failed to enable AA (error_mask=0x%x)\n",
				    err_mask);
			if (err_mask != AC_ERR_DEV) {
				dev->quirks |= ATA_QUIRK_BROKEN_FPDMA_AA;
				return -EIO;
			}
		} else
			aa_desc = ", AA";
	}

	if (hdepth >= ddepth)
		snprintf(desc, desc_sz, "NCQ (depth %d)%s", ddepth, aa_desc);
	else
		snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
			ddepth, aa_desc);

	if ((ap->flags & ATA_FLAG_FPDMA_AUX)) {
		if (ata_id_has_ncq_send_and_recv(dev->id))
			ata_dev_config_ncq_send_recv(dev);
		if (ata_id_has_ncq_non_data(dev->id))
			ata_dev_config_ncq_non_data(dev);
		if (ata_id_has_ncq_prio(dev->id))
			ata_dev_config_ncq_prio(dev);
	}

	return 0;
}

static void ata_dev_config_sense_reporting(struct ata_device *dev)
{
	unsigned int err_mask;

	if (!ata_id_has_sense_reporting(dev->id))
		return;

	if (ata_id_sense_reporting_enabled(dev->id))
		return;

	err_mask = ata_dev_set_feature(dev, SETFEATURE_SENSE_DATA, 0x1);
	if (err_mask) {
		ata_dev_dbg(dev,
			    "failed to enable Sense Data Reporting, Emask 0x%x\n",
			    err_mask);
	}
}

static void ata_dev_config_zoned(struct ata_device *dev)
{
	unsigned int err_mask;
	u8 *identify_buf = dev->sector_buf;

	dev->zac_zones_optimal_open = U32_MAX;
	dev->zac_zones_optimal_nonseq = U32_MAX;
	dev->zac_zones_max_open = U32_MAX;

	if (!ata_dev_is_zoned(dev))
		return;

	if (!ata_identify_page_supported(dev, ATA_LOG_ZONED_INFORMATION)) {
		ata_dev_warn(dev,
			     "ATA Zoned Information Log not supported\n");
		return;
	}

	/*
	 * Read IDENTIFY DEVICE data log, page 9 (Zoned-device information)
	 */
	err_mask = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_ZONED_INFORMATION,
				     identify_buf, 1);
	if (!err_mask) {
		u64 zoned_cap, opt_open, opt_nonseq, max_open;

		zoned_cap = get_unaligned_le64(&identify_buf[8]);
		if ((zoned_cap >> 63))
			dev->zac_zoned_cap = (zoned_cap & 1);
		opt_open = get_unaligned_le64(&identify_buf[24]);
		if ((opt_open >> 63))
			dev->zac_zones_optimal_open = (u32)opt_open;
		opt_nonseq = get_unaligned_le64(&identify_buf[32]);
		if ((opt_nonseq >> 63))
			dev->zac_zones_optimal_nonseq = (u32)opt_nonseq;
		max_open = get_unaligned_le64(&identify_buf[40]);
		if ((max_open >> 63))
			dev->zac_zones_max_open = (u32)max_open;
	}
}

static void ata_dev_config_trusted(struct ata_device *dev)
{
	u64 trusted_cap;
	unsigned int err;

	if (!ata_id_has_trusted(dev->id))
		return;

	if (!ata_identify_page_supported(dev, ATA_LOG_SECURITY)) {
		ata_dev_warn(dev,
			     "Security Log not supported\n");
		return;
	}

	err = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE, ATA_LOG_SECURITY,
				dev->sector_buf, 1);
	if (err)
		return;

	trusted_cap = get_unaligned_le64(&dev->sector_buf[40]);
	if (!(trusted_cap & (1ULL << 63))) {
		ata_dev_dbg(dev,
			    "Trusted Computing capability qword not valid!\n");
		return;
	}

	if (trusted_cap & (1 << 0))
		dev->flags |= ATA_DFLAG_TRUSTED;
}

static void ata_dev_cleanup_cdl_resources(struct ata_device *dev)
{
	kfree(dev->cdl);
	dev->cdl = NULL;
}

static int ata_dev_init_cdl_resources(struct ata_device *dev)
{
	struct ata_cdl *cdl = dev->cdl;
	unsigned int err_mask;

	if (!cdl) {
		cdl = kzalloc_obj(*cdl);
		if (!cdl)
			return -ENOMEM;
		dev->cdl = cdl;
	}

	err_mask = ata_read_log_page(dev, ATA_LOG_CDL, 0, cdl->desc_log_buf,
				     ATA_LOG_CDL_SIZE / ATA_SECT_SIZE);
	if (err_mask) {
		ata_dev_warn(dev, "Read Command Duration Limits log failed\n");
		ata_dev_cleanup_cdl_resources(dev);
		return -EIO;
	}

	return 0;
}

static void ata_dev_config_cdl(struct ata_device *dev)
{
	unsigned int err_mask;
	bool cdl_enabled;
	u64 val;
	int ret;

	if (ata_id_major_version(dev->id) < 11)
		goto not_supported;

	if (!ata_log_supported(dev, ATA_LOG_IDENTIFY_DEVICE) ||
	    !ata_identify_page_supported(dev, ATA_LOG_SUPPORTED_CAPABILITIES) ||
	    !ata_identify_page_supported(dev, ATA_LOG_CURRENT_SETTINGS))
		goto not_supported;

	err_mask = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_SUPPORTED_CAPABILITIES,
				     dev->sector_buf, 1);
	if (err_mask)
		goto not_supported;

	/* Check Command Duration Limit Supported bits */
	val = get_unaligned_le64(&dev->sector_buf[168]);
	if (!(val & BIT_ULL(63)) || !(val & BIT_ULL(0)))
		goto not_supported;

	/* Warn the user if command duration guideline is not supported */
	if (!(val & BIT_ULL(1)))
		ata_dev_warn(dev,
			"Command duration guideline is not supported\n");

	/*
	 * We must have support for the sense data for successful NCQ commands
	 * log indicated by the successful NCQ command sense data supported bit.
	 */
	val = get_unaligned_le64(&dev->sector_buf[8]);
	if (!(val & BIT_ULL(63)) || !(val & BIT_ULL(47))) {
		ata_dev_warn(dev,
			"CDL supported but Successful NCQ Command Sense Data is not supported\n");
		goto not_supported;
	}

	/* Without NCQ autosense, the successful NCQ commands log is useless. */
	if (!ata_id_has_ncq_autosense(dev->id)) {
		ata_dev_warn(dev,
			"CDL supported but NCQ autosense is not supported\n");
		goto not_supported;
	}

	/*
	 * If CDL is marked as enabled, make sure the feature is enabled too.
	 * Conversely, if CDL is disabled, make sure the feature is turned off.
	 */
	err_mask = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_CURRENT_SETTINGS,
				     dev->sector_buf, 1);
	if (err_mask)
		goto not_supported;

	val = get_unaligned_le64(&dev->sector_buf[8]);
	cdl_enabled = val & BIT_ULL(63) && val & BIT_ULL(21);
	if (dev->flags & ATA_DFLAG_CDL_ENABLED) {
		if (!cdl_enabled) {
			/* Enable CDL on the device */
			err_mask = ata_dev_set_feature(dev, SETFEATURES_CDL, 1);
			if (err_mask) {
				ata_dev_err(dev,
					    "Enable CDL feature failed\n");
				goto not_supported;
			}
		}
	} else {
		if (cdl_enabled) {
			/* Disable CDL on the device */
			err_mask = ata_dev_set_feature(dev, SETFEATURES_CDL, 0);
			if (err_mask) {
				ata_dev_err(dev,
					    "Disable CDL feature failed\n");
				goto not_supported;
			}
		}
	}

	/*
	 * While CDL itself has to be enabled using sysfs, CDL requires that
	 * sense data for successful NCQ commands is enabled to work properly.
	 * Just like ata_dev_config_sense_reporting(), enable it unconditionally
	 * if supported.
	 */
	if (!(val & BIT_ULL(63)) || !(val & BIT_ULL(18))) {
		err_mask = ata_dev_set_feature(dev,
					SETFEATURE_SENSE_DATA_SUCC_NCQ, 0x1);
		if (err_mask) {
			ata_dev_warn(dev,
				     "failed to enable Sense Data for successful NCQ commands, Emask 0x%x\n",
				     err_mask);
			goto not_supported;
		}
	}

	/* CDL is supported: allocate and initialize needed resources. */
	ret = ata_dev_init_cdl_resources(dev);
	if (ret) {
		ata_dev_warn(dev, "Initialize CDL resources failed\n");
		goto not_supported;
	}

	dev->flags |= ATA_DFLAG_CDL;

	return;

not_supported:
	dev->flags &= ~(ATA_DFLAG_CDL | ATA_DFLAG_CDL_ENABLED);
	ata_dev_cleanup_cdl_resources(dev);
}

static void ata_dev_config_depop(struct ata_device *dev)
{
	unsigned int err_mask;
	u64 val;

	/* Ignore old drives. */
	if (ata_id_major_version(dev->id) < 11)
		goto not_supported;

	/* NCQ Autosense is required. */
	if (!ata_identify_page_supported(dev, ATA_LOG_SUPPORTED_CAPABILITIES) ||
	    !ata_id_has_ncq_autosense(dev->id))
		goto not_supported;

	err_mask = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_SUPPORTED_CAPABILITIES,
				     dev->sector_buf, 1);
	if (err_mask)
		goto not_supported;

	/* Check depopulation capabilities bits. */
	val = get_unaligned_le64(&dev->sector_buf[152]);
	if (!(val & BIT_ULL(63)))
		goto not_supported;

	/*
	 * Support for at least the GET PHYSICAL ELEMENT STATUS and
	 * REMOVE ELEMENT AND TRUNCATE commands is mandated.
	 */
	if (!(val & BIT_ULL(0)) || !(val & BIT_ULL(1)))
		goto not_supported;

	dev->flags |= ATA_DFLAG_DEPOP;

	/* Check if RESTORE ELEMENTS AND REBUILD is supported. */
	if (val & BIT_ULL(2))
		dev->flags |= ATA_DFLAG_DEPOP_RESTORE;

	/*
	 * For ZAC devices, check if REMOVE ELEMENT AND MODIFY ZONES is
	 * supported.
	 */
	if (dev->class != ATA_DEV_ZAC)
		return;

	err_mask = ata_read_log_page(dev, ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_ZONED_INFORMATION,
				     dev->sector_buf, 1);
	if (err_mask)
		return;

	val = get_unaligned_le64(&dev->sector_buf[8]);
	if (!(val & BIT_ULL(63)))
		return;

	if (val & BIT_ULL(1))
		dev->flags |= ATA_DFLAG_DEPOP_MODIFY;

	return;

not_supported:
	dev->flags &= ~(ATA_DFLAG_DEPOP | ATA_DFLAG_DEPOP_RESTORE |
			ATA_DFLAG_DEPOP_MODIFY);
}

static int ata_dev_config_lba(struct ata_device *dev)
{
	const u16 *id = dev->id;
	const char *lba_desc;
	char ncq_desc[32];
	int ret;

	dev->flags |= ATA_DFLAG_LBA;

	if (ata_id_has_lba48(id)) {
		lba_desc = "LBA48";
		dev->flags |= ATA_DFLAG_LBA48;
		if (dev->n_sectors >= (1UL << 28) &&
		    ata_id_has_flush_ext(id))
			dev->flags |= ATA_DFLAG_FLUSH_EXT;
	} else {
		lba_desc = "LBA";
	}

	/* config NCQ */
	ret = ata_dev_config_ncq(dev, ncq_desc, sizeof(ncq_desc));

	/* print device info to dmesg */
	if (ata_dev_print_info(dev))
		ata_dev_info(dev,
			     "%llu sectors, multi %u: %s %s\n",
			     (unsigned long long)dev->n_sectors,
			     dev->multi_count, lba_desc, ncq_desc);

	return ret;
}

static void ata_dev_config_chs(struct ata_device *dev)
{
	const u16 *id = dev->id;

	if (ata_id_current_chs_valid(id)) {
		/* Current CHS translation is valid. */
		dev->cylinders = id[54];
		dev->heads     = id[55];
		dev->sectors   = id[56];
	} else {
		/* Default translation */
		dev->cylinders	= id[1];
		dev->heads	= id[3];
		dev->sectors	= id[6];
	}

	/* print device info to dmesg */
	if (ata_dev_print_info(dev))
		ata_dev_info(dev,
			     "%llu sectors, multi %u, CHS %u/%u/%u\n",
			     (unsigned long long)dev->n_sectors,
			     dev->multi_count, dev->cylinders,
			     dev->heads, dev->sectors);
}

static void ata_dev_config_fua(struct ata_device *dev)
{
	/* Ignore FUA support if its use is disabled globally */
	if (!libata_fua)
		goto nofua;

	/* Ignore devices without support for WRITE DMA FUA EXT */
	if (!(dev->flags & ATA_DFLAG_LBA48) || !ata_id_has_fua(dev->id))
		goto nofua;

	/* Ignore known bad devices and devices that lack NCQ support */
	if (!ata_ncq_supported(dev) || (dev->quirks & ATA_QUIRK_NO_FUA))
		goto nofua;

	dev->flags |= ATA_DFLAG_FUA;

	return;

nofua:
	dev->flags &= ~ATA_DFLAG_FUA;
}

static void ata_dev_config_devslp(struct ata_device *dev)
{
	u8 *sata_setting = dev->sector_buf;
	unsigned int err_mask;
	int i, j;

	/*
	 * Check device sleep capability. Get DevSlp timing variables
	 * from SATA Settings page of Identify Device Data Log.
	 */
	if (!ata_id_has_devslp(dev->id) ||
	    !ata_identify_page_supported(dev, ATA_LOG_SATA_SETTINGS))
		return;

	err_mask = ata_read_log_page(dev,
				     ATA_LOG_IDENTIFY_DEVICE,
				     ATA_LOG_SATA_SETTINGS,
				     sata_setting, 1);
	if (err_mask)
		return;

	dev->flags |= ATA_DFLAG_DEVSLP;
	for (i = 0; i < ATA_LOG_DEVSLP_SIZE; i++) {
		j = ATA_LOG_DEVSLP_OFFSET + i;
		dev->devslp_timing[i] = sata_setting[j];
	}
}

static void ata_dev_config_cpr(struct ata_device *dev)
{
	unsigned int err_mask;
	size_t buf_len;
	int i, nr_cpr = 0;
	struct ata_cpr_log *cpr_log = NULL;
	u8 *desc, *buf = NULL;

	if (ata_id_major_version(dev->id) < 11)
		goto out;

	buf_len = ata_log_supported(dev, ATA_LOG_CONCURRENT_POSITIONING_RANGES);
	if (buf_len == 0)
		goto out;

	/*
	 * Read the concurrent positioning ranges log (0x47). We can have at
	 * most 255 32B range descriptors plus a 64B header. This log varies in
	 * size, so use the size reported in the GPL directory. Reading beyond
	 * the supported length will result in an error.
	 */
	buf_len <<= 9;
	buf = kzalloc(buf_len, GFP_KERNEL);
	if (!buf)
		goto out;

	err_mask = ata_read_log_page(dev, ATA_LOG_CONCURRENT_POSITIONING_RANGES,
				     0, buf, buf_len >> 9);
	if (err_mask)
		goto out;

	nr_cpr = buf[0];
	if (!nr_cpr)
		goto out;

	/*
	 * The device reports the number of CPR descriptors independently of the
	 * log size, and that count is also used to emit VPD page B9h into the
	 * fixed-size rbuf. Reject a count larger than what that buffer can hold
	 * (ATA_DEV_MAX_CPR) or larger than the log the device actually returned.
	 */
	if (nr_cpr > ATA_DEV_MAX_CPR) {
		ata_dev_warn(dev,
			     "Too many concurrent positioning ranges\n");
		goto out;
	}

	if (buf_len < 64 + (size_t)nr_cpr * 32) {
		ata_dev_warn(dev,
			     "Invalid number of concurrent positioning ranges\n");
		goto out;
	}

	cpr_log = kzalloc_flex(*cpr_log, cpr, nr_cpr);
	if (!cpr_log)
		goto out;

	cpr_log->nr_cpr = nr_cpr;
	desc = &buf[64];
	for (i = 0; i < nr_cpr; i++, desc += 32) {
		cpr_log->cpr[i].num = desc[0];
		cpr_log->cpr[i].num_storage_elements = desc[1];
		cpr_log->cpr[i].start_lba = get_unaligned_le64(&desc[8]);
		cpr_log->cpr[i].num_lbas = get_unaligned_le64(&desc[16]);
	}

out:
	swap(dev->cpr_log, cpr_log);
	kfree(cpr_log);
	kfree(buf);
}

/*
 * Configure features related to link power management.
 */
static void ata_dev_config_lpm(struct ata_device *dev)
{
	struct ata_port *ap = dev->link->ap;
	unsigned int err_mask;

	if (ap->flags & ATA_FLAG_NO_LPM) {
		/*
		 * When the port does not support LPM, we cannot support it on
		 * the device either.
		 */
		dev->quirks |= ATA_QUIRK_NOLPM;
	} else {
		/*
		 * Some WD SATA-1 drives have issues with LPM, turn on NOLPM for
		 * them.
		 */
		if ((dev->quirks & ATA_QUIRK_WD_BROKEN_LPM) &&
		    (dev->id[ATA_ID_SATA_CAPABILITY] & 0xe) == 0x2)
			dev->quirks |= ATA_QUIRK_NOLPM;

		/* ATI specific quirk */
		if ((dev->quirks & ATA_QUIRK_NO_LPM_ON_ATI) &&
		    ata_dev_check_adapter(dev, PCI_VENDOR_ID_ATI))
			dev->quirks |= ATA_QUIRK_NOLPM;
	}

	if (dev->quirks & ATA_QUIRK_NOLPM &&
	    ap->target_lpm_policy != ATA_LPM_MAX_POWER) {
		ata_dev_warn(dev, "LPM support broken, forcing max_power\n");
		ap->target_lpm_policy = ATA_LPM_MAX_POWER;
	}

	/*
	 * Device Initiated Power Management (DIPM) is normally disabled by
	 * default on a device. However, DIPM may have been enabled and that
	 * setting kept even after COMRESET because of the Software Settings
	 * Preservation feature. So if the port does not support DIPM and the
	 * device does, disable DIPM on the device.
	 */
	if (ap->flags & ATA_FLAG_NO_DIPM && ata_id_has_dipm(dev->id)) {
		err_mask = ata_dev_set_feature(dev,
					SETFEATURES_SATA_DISABLE, SATA_DIPM);
		if (err_mask && err_mask != AC_ERR_DEV)
			ata_dev_err(dev, "Disable DIPM failed, Emask 0x%x\n",
				    err_mask);
	}
}

static void ata_dev_print_features(struct ata_device *dev)
{
	if (!(dev->flags & ATA_DFLAG_FEATURES_MASK) && !dev->cpr_log &&
	    !ata_id_has_hipm(dev->id) && !ata_id_has_dipm(dev->id))
		return;

	ata_dev_info(dev,
		     "Features:%s%s%s%s%s%s%s%s%s%s%s%s%s\n",
		     dev->flags & ATA_DFLAG_FUA ? " FUA" : "",
		     dev->flags & ATA_DFLAG_TRUSTED ? " Trust" : "",
		     dev->flags & ATA_DFLAG_DA ? " Dev-Attention" : "",
		     dev->flags & ATA_DFLAG_DEVSLP ? " Dev-Sleep" : "",
		     ata_id_has_hipm(dev->id) ? " HIPM" : "",
		     ata_id_has_dipm(dev->id) ? " DIPM" : "",
		     dev->flags & ATA_DFLAG_NCQ_SEND_RECV ? " NCQ-sndrcv" : "",
		     dev->flags & ATA_DFLAG_NCQ_PRIO ? " NCQ-prio" : "",
		     dev->flags & ATA_DFLAG_CDL ? " CDL" : "",
		     dev->cpr_log ? " CPR" : "",
		     dev->flags & ATA_DFLAG_DEPOP ? " Depop" : "",
		     dev->flags & ATA_DFLAG_DEPOP_RESTORE ? " Depop-Restore" : "",
		     dev->flags & ATA_DFLAG_DEPOP_MODIFY ? " Depop-Modify" : "");
}

/**
 *	ata_dev_configure - Configure the specified ATA/ATAPI device
 *	@dev: Target device to configure
 *
 *	Configure @dev according to @dev->id.  Generic and low-level
 *	driver specific fixups are also applied.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	0 on success, -errno otherwise
 */
int ata_dev_configure(struct ata_device *dev)
{
	struct ata_port *ap = dev->link->ap;
	bool print_info = ata_dev_print_info(dev);
	const u16 *id = dev->id;
	unsigned int xfer_mask;
	unsigned int err_mask;
	char revbuf[7];		/* XYZ-99\0 */
	char fwrevbuf[ATA_ID_FW_REV_LEN+1];
	char modelbuf[ATA_ID_PROD_LEN+1];
	int rc;

	if (!ata_dev_enabled(dev)) {
		ata_dev_dbg(dev, "no device\n");
		return 0;
	}

	/* Clear the general purpose log directory cache. */
	ata_clear_log_directory(dev);

	/* Set quirks */
	dev->quirks |= ata_dev_quirks(dev);
	ata_force_quirks(dev);

	if (dev->quirks & ATA_QUIRK_DISABLE) {
		ata_dev_info(dev, "unsupported device, disabling\n");
		ata_dev_disable(dev);
		return 0;
	}

	if ((!atapi_enabled || (ap->flags & ATA_FLAG_NO_ATAPI)) &&
	    dev->class == ATA_DEV_ATAPI) {
		ata_dev_warn(dev, "WARNING: ATAPI is %s, device ignored\n",
			     atapi_enabled ? "not supported with this driver"
			     : "disabled");
		ata_dev_disable(dev);
		return 0;
	}

	rc = ata_do_link_spd_quirk(dev);
	if (rc)
		return rc;

	/* let ACPI work its magic */
	rc = ata_acpi_on_devcfg(dev);
	if (rc)
		return rc;

	/* massage HPA, do it early as it might change IDENTIFY data */
	rc = ata_hpa_resize(dev);
	if (rc)
		return rc;

	/* print device capabilities */
	ata_dev_dbg(dev,
		    "%s: cfg 49:%04x 82:%04x 83:%04x 84:%04x "
		    "85:%04x 86:%04x 87:%04x 88:%04x\n",
		    __func__,
		    id[49], id[82], id[83], id[84],
		    id[85], id[86], id[87], id[88]);

	/* initialize to-be-configured parameters */
	dev->flags &= ~ATA_DFLAG_CFG_MASK;
	dev->max_sectors = 0;
	dev->cdb_len = 0;
	dev->n_sectors = 0;
	dev->cylinders = 0;
	dev->heads = 0;
	dev->sectors = 0;
	dev->multi_count = 0;

	/*
	 * common ATA, ATAPI feature tests
	 */

	/* find max transfer mode; for printk only */
	xfer_mask = ata_id_xfermask(id);

	ata_dump_id(dev, id);

	/* SCSI only uses 4-char revisions, dump full 8 chars from ATA */
	ata_id_c_string(dev->id, fwrevbuf, ATA_ID_FW_REV,
			sizeof(fwrevbuf));

	ata_id_c_string(dev->id, modelbuf, ATA_ID_PROD,
			sizeof(modelbuf));

	/* ATA-specific feature tests */
	if (dev->class == ATA_DEV_ATA || dev->class == ATA_DEV_ZAC) {
		if (ata_id_is_cfa(id)) {
			/* CPRM may make this media unusable */
			if (id[ATA_ID_CFA_KEY_MGMT] & 1)
				ata_dev_warn(dev,
	"supports DRM functions and may not be fully accessible\n");
			snprintf(revbuf, 7, "CFA");
		} else {
			snprintf(revbuf, 7, "ATA-%d", ata_id_major_version(id));
			/* Warn the user if the device has TPM extensions */
			if (ata_id_has_tpm(id))
				ata_dev_warn(dev,
	"supports DRM functions and may not be fully accessible\n");
		}

		dev->n_sectors = ata_id_n_sectors(id);
		if (ata_id_is_locked(id)) {
			/*
			 * If Security locked, set capacity to zero to prevent
			 * any I/O, e.g. partition scanning, as any I/O to a
			 * locked drive will result in user visible errors.
			 */
			ata_dev_info(dev,
				"Security locked, setting capacity to zero\n");
			dev->n_sectors = 0;
		}

		/* get current R/W Multiple count setting */
		if ((dev->id[47] >> 8) == 0x80 && (dev->id[59] & 0x100)) {
			unsigned int max = dev->id[47] & 0xff;
			unsigned int cnt = dev->id[59] & 0xff;
			/* only recognize/allow powers of two here */
			if (is_power_of_2(max) && is_power_of_2(cnt))
				if (cnt <= max)
					dev->multi_count = cnt;
		}

		/* print device info to dmesg */
		if (print_info)
			ata_dev_info(dev, "%s: %s, %s, max %s\n",
				     revbuf, modelbuf, fwrevbuf,
				     ata_mode_string(xfer_mask));

		if (ata_id_has_lba(id)) {
			rc = ata_dev_config_lba(dev);
			if (rc)
				return rc;
		} else {
			ata_dev_config_chs(dev);
		}

		ata_dev_config_lpm(dev);
		ata_dev_config_fua(dev);
		ata_dev_config_devslp(dev);
		ata_dev_config_sense_reporting(dev);
		ata_dev_config_zoned(dev);
		ata_dev_config_trusted(dev);
		ata_dev_config_cpr(dev);
		ata_dev_config_cdl(dev);
		ata_dev_config_depop(dev);
		dev->cdb_len = 32;

		if (print_info)
			ata_dev_print_features(dev);
	}

	/* ATAPI-specific feature tests */
	else if (dev->class == ATA_DEV_ATAPI) {
		const char *cdb_intr_string = "";
		const char *atapi_an_string = "";
		const char *dma_dir_string = "";
		u32 sntf;

		rc = atapi_cdb_len(id);
		if ((rc < 12) || (rc > ATAPI_CDB_LEN)) {
			ata_dev_warn(dev, "unsupported CDB len %d\n", rc);
			rc = -EINVAL;
			goto err_out_nosup;
		}
		dev->cdb_len = (unsigned int) rc;

		/* Enable ATAPI AN if both the host and device have
		 * the support.  If PMP is attached, SNTF is required
		 * to enable ATAPI AN to discern between PHY status
		 * changed notifications and ATAPI ANs.
		 */
		if (atapi_an &&
		    (ap->flags & ATA_FLAG_AN) && ata_id_has_atapi_AN(id) &&
		    (!sata_pmp_attached(ap) ||
		     sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf) == 0)) {
			/* issue SET feature command to turn this on */
			err_mask = ata_dev_set_feature(dev,
					SETFEATURES_SATA_ENABLE, SATA_AN);
			if (err_mask)
				ata_dev_err(dev,
					    "failed to enable ATAPI AN (err_mask=0x%x)\n",
					    err_mask);
			else {
				dev->flags |= ATA_DFLAG_AN;
				atapi_an_string = ", ATAPI AN";
			}
		}

		if (ata_id_cdb_intr(dev->id)) {
			dev->flags |= ATA_DFLAG_CDB_INTR;
			cdb_intr_string = ", CDB intr";
		}

		if (atapi_dmadir || (dev->quirks & ATA_QUIRK_ATAPI_DMADIR) ||
		    atapi_id_dmadir(dev->id)) {
			dev->flags |= ATA_DFLAG_DMADIR;
			dma_dir_string = ", DMADIR";
		}

		if (ata_id_has_da(dev->id)) {
			dev->flags |= ATA_DFLAG_DA;
			zpodd_init(dev);
		}

		/* print device info to dmesg */
		if (print_info)
			ata_dev_info(dev,
				     "ATAPI: %s, %s, max %s%s%s%s\n",
				     modelbuf, fwrevbuf,
				     ata_mode_string(xfer_mask),
				     cdb_intr_string, atapi_an_string,
				     dma_dir_string);

		ata_dev_config_lpm(dev);

		if (print_info)
			ata_dev_print_features(dev);
	}

	/* determine max_sectors */
	dev->max_sectors = ATA_MAX_SECTORS;
	if (dev->flags & ATA_DFLAG_LBA48)
		dev->max_sectors = ATA_MAX_SECTORS_LBA48;

	/* Limit PATA drive on SATA cable bridge transfers to udma5,
	   200 sectors */
	if (ata_dev_knobble(dev)) {
		if (print_info)
			ata_dev_info(dev, "applying bridge limits\n");
		dev->udma_mask &= ATA_UDMA5;
		dev->max_sectors = ATA_MAX_SECTORS;
	}

	if ((dev->class == ATA_DEV_ATAPI) &&
	    (atapi_command_packet_set(id) == TYPE_TAPE)) {
		dev->max_sectors = ATA_MAX_SECTORS_TAPE;
		dev->quirks |= ATA_QUIRK_STUCK_ERR;
	}

	if (dev->quirks & ATA_QUIRK_MAX_SEC)
		dev->max_sectors = min_t(unsigned int, dev->max_sectors,
					 ata_dev_get_quirk_value(dev,
							 ATA_QUIRK_MAX_SEC));

	if (dev->quirks & ATA_QUIRK_MAX_SEC_LBA48)
		dev->max_sectors = ATA_MAX_SECTORS_LBA48;

	if (ap->ops->dev_config)
		ap->ops->dev_config(dev);

	if (dev->quirks & ATA_QUIRK_DIAGNOSTIC) {
		/* Let the user know. We don't want to disallow opens for
		   rescue purposes, or in case the vendor is just a blithering
		   idiot. Do this after the dev_config call as some controllers
		   with buggy firmware may want to avoid reporting false device
		   bugs */

		if (print_info) {
			ata_dev_warn(dev,
"Drive reports diagnostics failure. This may indicate a drive\n");
			ata_dev_warn(dev,
"fault or invalid emulation. Contact drive vendor for information.\n");
		}
	}

	if ((dev->quirks & ATA_QUIRK_FIRMWARE_WARN) && print_info) {
		ata_dev_warn(dev, "WARNING: device requires firmware update to be fully functional\n");
		ata_dev_warn(dev, "         contact the vendor or visit http://ata.wiki.kernel.org\n");
	}

	return 0;

err_out_nosup:
	return rc;
}

/**
 *	ata_cable_40wire	-	return 40 wire cable type
 *	@ap: port
 *
 *	Helper method for drivers which want to hardwire 40 wire cable
 *	detection.
 */

int ata_cable_40wire(struct ata_port *ap)
{
	return ATA_CBL_PATA40;
}
EXPORT_SYMBOL_GPL(ata_cable_40wire);

/**
 *	ata_cable_80wire	-	return 80 wire cable type
 *	@ap: port
 *
 *	Helper method for drivers which want to hardwire 80 wire cable
 *	detection.
 */

int ata_cable_80wire(struct ata_port *ap)
{
	return ATA_CBL_PATA80;
}
EXPORT_SYMBOL_GPL(ata_cable_80wire);

/**
 *	ata_cable_unknown	-	return unknown PATA cable.
 *	@ap: port
 *
 *	Helper method for drivers which have no PATA cable detection.
 */

int ata_cable_unknown(struct ata_port *ap)
{
	return ATA_CBL_PATA_UNK;
}
EXPORT_SYMBOL_GPL(ata_cable_unknown);

/**
 *	ata_cable_ignore	-	return ignored PATA cable.
 *	@ap: port
 *
 *	Helper method for drivers which don't use cable type to limit
 *	transfer mode.
 */
int ata_cable_ignore(struct ata_port *ap)
{
	return ATA_CBL_PATA_IGN;
}
EXPORT_SYMBOL_GPL(ata_cable_ignore);

/**
 *	ata_cable_sata	-	return SATA cable type
 *	@ap: port
 *
 *	Helper method for drivers which have SATA cables
 */

int ata_cable_sata(struct ata_port *ap)
{
	return ATA_CBL_SATA;
}
EXPORT_SYMBOL_GPL(ata_cable_sata);

/**
 *	sata_print_link_status - Print SATA link status
 *	@link: SATA link to printk link status about
 *
 *	This function prints link speed and status of a SATA link.
 *
 *	LOCKING:
 *	None.
 */
static void sata_print_link_status(struct ata_link *link)
{
	u32 sstatus, scontrol, tmp;

	if (sata_scr_read(link, SCR_STATUS, &sstatus))
		return;
	if (sata_scr_read(link, SCR_CONTROL, &scontrol))
		return;

	if (ata_phys_link_online(link)) {
		tmp = (sstatus >> 4) & 0xf;
		ata_link_info(link, "SATA link up %s (SStatus %X SControl %X)\n",
			      sata_spd_string(tmp), sstatus, scontrol);
	} else {
		ata_link_info(link, "SATA link down (SStatus %X SControl %X)\n",
			      sstatus, scontrol);
	}
}

/**
 *	ata_dev_pair		-	return other device on cable
 *	@adev: device
 *
 *	Obtain the other device on the same cable, or if none is
 *	present NULL is returned
 */

struct ata_device *ata_dev_pair(struct ata_device *adev)
{
	struct ata_link *link = adev->link;
	struct ata_device *pair = &link->device[1 - adev->devno];
	if (!ata_dev_enabled(pair))
		return NULL;
	return pair;
}
EXPORT_SYMBOL_GPL(ata_dev_pair);

#ifdef CONFIG_ATA_ACPI
/**
 *	ata_timing_cycle2mode - find xfer mode for the specified cycle duration
 *	@xfer_shift: ATA_SHIFT_* value for transfer type to examine.
 *	@cycle: cycle duration in ns
 *
 *	Return matching xfer mode for @cycle.  The returned mode is of
 *	the transfer type specified by @xfer_shift.  If @cycle is too
 *	slow for @xfer_shift, 0xff is returned.  If @cycle is faster
 *	than the fastest known mode, the fasted mode is returned.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	Matching xfer_mode, 0xff if no match found.
 */
u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle)
{
	u8 base_mode = 0xff, last_mode = 0xff;
	const struct ata_xfer_ent *ent;
	const struct ata_timing *t;

	for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
		if (ent->shift == xfer_shift)
			base_mode = ent->base;

	for (t = ata_timing_find_mode(base_mode);
	     t && ata_xfer_mode2shift(t->mode) == xfer_shift; t++) {
		unsigned short this_cycle;

		switch (xfer_shift) {
		case ATA_SHIFT_PIO:
		case ATA_SHIFT_MWDMA:
			this_cycle = t->cycle;
			break;
		case ATA_SHIFT_UDMA:
			this_cycle = t->udma;
			break;
		default:
			return 0xff;
		}

		if (cycle > this_cycle)
			break;

		last_mode = t->mode;
	}

	return last_mode;
}
#endif

/**
 *	ata_down_xfermask_limit - adjust dev xfer masks downward
 *	@dev: Device to adjust xfer masks
 *	@sel: ATA_DNXFER_* selector
 *
 *	Adjust xfer masks of @dev downward.  Note that this function
 *	does not apply the change.  Invoking ata_set_mode() afterwards
 *	will apply the limit.
 *
 *	LOCKING:
 *	Inherited from caller.
 *
 *	RETURNS:
 *	0 on success, negative errno on failure
 */
int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel)
{
	char buf[32];
	unsigned int orig_mask, xfer_mask;
	unsigned int pio_mask, mwdma_mask, udma_mask;
	int quiet, highbit;

	quiet = !!(sel & ATA_DNXFER_QUIET);
	sel &= ~ATA_DNXFER_QUIET;

	xfer_mask = orig_mask = ata_pack_xfermask(dev->pio_mask,
						  dev->mwdma_mask,
						  dev->udma_mask);
	ata_unpack_xfermask(xfer_mask, &pio_mask, &mwdma_mask, &udma_mask);

	switch (sel) {
	case ATA_DNXFER_PIO:
		highbit = fls(pio_mask) - 1;
		pio_mask &= ~(1 << highbit);
		break;

	case ATA_DNXFER_DMA:
		if (udma_mask) {
			highbit = fls(udma_mask) - 1;
			udma_mask &= ~(1 << highbit);
			if (!udma_mask)
				return -ENOENT;
		} else if (mwdma_mask) {
			highbit = fls(mwdma_mask) - 1;
			mwdma_mask &= ~(1 << highbit);
			if (!mwdma_mask)
				return -ENOENT;
		}
		break;

	case ATA_DNXFER_40C:
		udma_mask &= ATA_UDMA_MASK_40C;
		break;

	case ATA_DNXFER_FORCE_PIO0:
		pio_mask &= 1;
		fallthrough;
	case ATA_DNXFER_FORCE_PIO:
		mwdma_mask = 0;
		udma_mask = 0;
		break;

	default:
		BUG();
	}

	xfer_mask &= ata_pack_xfermask(pio_mask, mwdma_mask, udma_mask);

	if (!(xfer_mask & ATA_MASK_PIO) || xfer_mask == orig_mask)
		return -ENOENT;

	if (!quiet) {
		if (xfer_mask & (ATA_MASK_MWDMA | ATA_MASK_UDMA))
			snprintf(buf, sizeof(buf), "%s:%s",
				 ata_mode_string(xfer_mask),
				 ata_mode_string(xfer_mask & ATA_MASK_PIO));
		else
			snprintf(buf, sizeof(buf), "%s",
				 ata_mode_string(xfer_mask));

		ata_dev_warn(dev, "limiting speed to %s\n", buf);
	}

	ata_unpack_xfermask(xfer_mask, &dev->pio_mask, &dev->mwdma_mask,
			    &dev->udma_mask);

	return 0;
}

static int ata_dev_set_mode(struct ata_device *dev)
{
	struct ata_port *ap = dev->link->ap;
	struct ata_eh_context *ehc = &dev->link->eh_context;
	const bool nosetxfer = dev->quirks & ATA_QUIRK_NOSETXFER;
	const char *dev_err_whine = "";
	int ign_dev_err = 0;
	unsigned int err_mask = 0;
	int rc;

	dev->flags &= ~ATA_DFLAG_PIO;
	if (dev->xfer_shift == ATA_SHIFT_PIO)
		dev->flags |= ATA_DFLAG_PIO;

	if (nosetxfer && ap->flags & ATA_FLAG_SATA && ata_id_is_sata(dev->id))
		dev_err_whine = " (SET_XFERMODE skipped)";
	else {
		if (nosetxfer)
			ata_dev_warn(dev,
				     "NOSETXFER but PATA detected - can't "
				     "skip SETXFER, might malfunction\n");
		err_mask = ata_dev_set_xfermode(dev);
	}

	if (err_mask & ~AC_ERR_DEV)
		goto fail;

	/* revalidate */
	ehc->i.flags |= ATA_EHI_POST_SETMODE;
	rc = ata_dev_revalidate(dev, ATA_DEV_UNKNOWN, 0);
	ehc->i.flags &= ~ATA_EHI_POST_SETMODE;
	if (rc)
		return rc;

	if (dev->xfer_shift == ATA_SHIFT_PIO) {
		/* Old CFA may refuse this command, which is just fine */
		if (ata_id_is_cfa(dev->id))
			ign_dev_err = 1;
		/* Catch several broken garbage emulations plus some pre
		   ATA devices */
		if (ata_id_major_version(dev->id) == 0 &&
					dev->pio_mode <= XFER_PIO_2)
			ign_dev_err = 1;
		/* Some very old devices and some bad newer ones fail
		   any kind of SET_XFERMODE request but support PIO0-2
		   timings and no IORDY */
		if (!ata_id_has_iordy(dev->id) && dev->pio_mode <= XFER_PIO_2)
			ign_dev_err = 1;
	}
	/* Early MWDMA devices do DMA but don't allow DMA mode setting.
	   Don't fail an MWDMA0 set IFF the device indicates it is in MWDMA0 */
	if (dev->xfer_shift == ATA_SHIFT_MWDMA &&
	    dev->dma_mode == XFER_MW_DMA_0 &&
	    (dev->id[63] >> 8) & 1)
		ign_dev_err = 1;

	/* if the device is actually configured correctly, ignore dev err */
	if (dev->xfer_mode == ata_xfer_mask2mode(ata_id_xfermask(dev->id)))
		ign_dev_err = 1;

	if (err_mask & AC_ERR_DEV) {
		if (!ign_dev_err)
			goto fail;
		else
			dev_err_whine = " (device error ignored)";
	}

	ata_dev_dbg(dev, "xfer_shift=%u, xfer_mode=0x%x\n",
		    dev->xfer_shift, (int)dev->xfer_mode);

	if (!(ehc->i.flags & ATA_EHI_QUIET) ||
	    ehc->i.flags & ATA_EHI_DID_HARDRESET)
		ata_dev_info(dev, "configured for %s%s\n",
			     ata_mode_string(ata_xfer_mode2mask(dev->xfer_mode)),
			     dev_err_whine);

	return 0;

 fail:
	ata_dev_err(dev, "failed to set xfermode (err_mask=0x%x)\n", err_mask);
	return -EIO;
}

/**
 *	ata_set_mode - Program timings and issue SET FEATURES - XFER
 *	@link: link on which timings will be programmed
 *	@r_failed_dev: out parameter for failed device
 *
 *	Standard implementation of the function used to tune and set
 *	ATA device disk transfer mode (PIO3, UDMA6, etc.).  If
 *	ata_dev_set_mode() fails, pointer to the failing device is
 *	returned in @r_failed_dev.
 *
 *	LOCKING:
 *	PCI/etc. bus probe sem.
 *
 *	RETURNS:
 *	0 on success, negative errno otherwise
 */

int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
{
	struct ata_port *ap = link->ap;
	struct ata_device *dev;
	int rc = 0, used_dma = 0, found = 0;

	/* step 1: calculate xfer_mask */
	ata_for_each_dev(dev, link, ENABLED) {
		unsigned int pio_mask, dma_mask;
		unsigned int mode_mask;

		mode_mask = ATA_DMA_MASK_ATA;
		if (dev->class == ATA_DEV_ATAPI)
			mode_mask = ATA_DMA_MASK_ATAPI;
		else if (ata_id_is_cfa(dev->id))
			mode_mask = ATA_DMA_MASK_CFA;

		ata_dev_xfermask(dev);
		ata_force_xfermask(dev);

		pio_mask = ata_pack_xfermask(dev->pio_mask, 0, 0);

		if (libata_dma_mask & mode_mask)
			dma_mask = ata_pack_xfermask(0, dev->mwdma_mask,
						     dev->udma_mask);
		else
			dma_mask = 0;

		dev->pio_mode = ata_xfer_mask2mode(pio_mask);
		dev->dma_mode = ata_xfer_mask2mode(dma_mask);

		found = 1;
		if (ata_dma_enabled(dev))
			used_dma = 1;
	}
	if (!found)
		goto out;

	/* step 2: always set host PIO timings */
	ata_for_each_dev(dev, link, ENABLED) {
		if (dev->pio_mode == 0xff) {
			ata_dev_warn(dev, "no PIO support\n");
			rc = -EINVAL;
			goto out;
		}

		dev->xfer_mode = dev->pio_mode;
		dev->xfer_shift = ATA_SHIFT_PIO;
		if (ap->ops->set_piomode)
			ap->ops->set_piomode(ap, dev);
	}

	/* step 3: set host DMA timings */
	ata_for_each_dev(dev, link, ENABLED) {
		if (!ata_dma_enabled(dev))
			continue;

		dev->xfer_mode = dev->dma_mode;
		dev->xfer_shift = ata_xfer_mode2shift(dev->dma_mode);
		if (ap->ops->set_dmamode)
			ap->ops->set_dmamode(ap, dev);
	}

	/* step 4: update devices' xfer mode */
	ata_for_each_dev(dev, link, ENABLED) {
		rc = ata_dev_set_mode(dev);
		if (rc)
			goto out;
	}

	/* Record simplex status. If we selected DMA then the other
	 * host channels are not permitted to do so.
	 */
	if (used_dma && (ap->host->flags & ATA_HOST_SIMPLEX))
		ap->host->simplex_claimed = ap;

 out:
	if (rc)
		*r_failed_dev = dev;
	return rc;
}
EXPORT_SYMBOL_GPL(ata_set_mode);

/**
 *	ata_wait_ready - wait for link to become ready
 *	@link: link to be waited on
 *	@deadline: deadline jiffies for the operation
 *	@check_ready: callback to check link readiness
 *
 *	Wait for @link to become ready.  @check_ready should return
 *	positive number if @link is ready, 0 if it isn't, -ENODEV if
 *	link doesn't seem to be occupied, other errno for other error
 *	conditions.
 *
 *	Transient -ENODEV conditions are allowed for
 *	ATA_TMOUT_FF_WAIT.
 *
 *	LOCKING:
 *	EH context.
 *
 *	RETURNS:
 *	0 if @link is ready before @deadline; otherwise, -errno.
 */
int ata_wait_ready(struct ata_link *link, unsigned long deadline,
		   int (*check_ready)(struct ata_link *link))
{
	unsigned long start = jiffies;
	unsigned long nodev_deadline;
	int warned = 0;

	/* choose which 0xff timeout to use, read comment in libata.h */
	if (link->ap->host->flags & ATA_HOST_PARALLEL_SCAN)
		nodev_deadline = ata_deadline(start, ATA_TMOUT_FF_WAIT_LONG);
	else
		nodev_deadline = ata_deadline(start, ATA_TMOUT_FF_WAIT);

	/* Slave readiness can't be tested separately from master.  On
	 * M/S emulation configuration, this function should be called
	 * only on the master and it will handle both master and slave.
	 */
	WARN_ON(link == link->ap->slave_link);

	if (time_after(nodev_deadline, deadline))
		nodev_deadline = deadline;

	while (1) {
		unsigned long now = jiffies;
		int ready, tmp;

		ready = tmp = check_ready(link);
		if (ready > 0)
			return 0;

		/*
		 * -ENODEV could be transient.  Ignore -ENODEV if link
		 * is online.  Also, some SATA devices take a long
		 * time to clear 0xff after reset.  Wait for
		 * ATA_TMOUT_FF_WAIT[_LONG] on -ENODEV if link isn't
		 * offline.
		 *
		 * Note that some PATA controllers (pata_ali) explode
		 * if status register is read more than once when
		 * there's no device attached.
		 */
		if (ready == -ENODEV) {
			if (ata_link_online(link))
				ready = 0;
			else if ((link->ap->flags & ATA_FLAG_SATA) &&
				 !ata_link_offline(link) &&
				 time_before(now, nodev_deadline))
				ready = 0;
		}

		if (ready)
			return ready;
		if (time_after(now, deadline))
			return -EBUSY;

		if (!warned && time_after(now, start + 5 * HZ) &&
		    (deadline - now > 3 * HZ)) {
			ata_link_warn(link,
				"link is slow to respond, please be patient "
				"(ready=%d)\n", tmp);
			warned = 1;
		}

		ata_msleep(link->ap, 50);
	}
}

/**
 *	ata_wait_after_reset - wait for link to become ready after reset
 *	@link: link to be waited on
 *	@deadline: deadline jiffies for the operation
 *	@check_ready: callback to check link readiness
 *
 *	Wait for @link to become ready after reset.
 *
 *	LOCKING:
 *	EH context.
 *
 *	RETURNS:
 *	0 if @link is ready before @deadline; otherwise, -errno.
 */
int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
				int (*check_ready)(struct ata_link *link))
{
	ata_msleep(link->ap, ATA_WAIT_AFTER_RESET);

	return ata_wait_ready(link, deadline, check_ready);
}
EXPORT_SYMBOL_GPL(ata_wait_after_reset);

/**
 *	ata_std_prereset - prepare for reset
 *	@link: ATA link to be reset
 *	@deadline: deadline jiffies for the operation
 *
 *	@link is about to be reset.  Initialize it.  Failure from
 *	prereset makes libata abort whole reset sequence and give up
 *	that port, so prereset should be best-effort.  It does its
 *	best to prepare for reset sequence but if things go wrong, it
 *	should just whine, not fail.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	Always 0.
 */
int ata_std_prereset(struct ata_link *link, unsigned long deadline)
{
	struct ata_port *ap = link->ap;
	struct ata_eh_context *ehc = &link->eh_context;
	const unsigned int *timing = sata_ehc_deb_timing(ehc);
	int rc;

	/* if we're about to do hardreset, nothing more to do */
	if (ehc->i.action & ATA_EH_HARDRESET)
		return 0;

	/* if SATA, resume link */
	if (ap->flags & ATA_FLAG_SATA) {
		rc = sata_link_resume(link, timing, deadline);
		/* whine about phy resume failure but proceed */
		if (rc && rc != -EOPNOTSUPP)
			ata_link_warn(link,
				      "failed to resume link for reset (errno=%d)\n",
				      rc);
	}

	/* no point in trying softreset on offline link */
	if (ata_phys_link_offline(link))
		ehc->i.action &= ~ATA_EH_SOFTRESET;

	return 0;
}
EXPORT_SYMBOL_GPL(ata_std_prereset);

/**
 *	ata_std_postreset - standard postreset callback
 *	@link: the target ata_link
 *	@classes: classes of attached devices
 *
 *	This function is invoked after a successful reset.  Note that
 *	the device might have been reset more than once using
 *	different reset methods before postreset is invoked.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 */
void ata_std_postreset(struct ata_link *link, unsigned int *classes)
{
	u32 serror;

	/* reset complete, clear SError */
	if (!sata_scr_read(link, SCR_ERROR, &serror))
		sata_scr_write(link, SCR_ERROR, serror);

	/* print link status */
	sata_print_link_status(link);
}
EXPORT_SYMBOL_GPL(ata_std_postreset);

/**
 *	ata_dev_same_device - Determine whether new ID matches configured device
 *	@dev: device to compare against
 *	@new_class: class of the new device
 *	@new_id: IDENTIFY page of the new device
 *
 *	Compare @new_class and @new_id against @dev and determine
 *	whether @dev is the device indicated by @new_class and
 *	@new_id.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	1 if @dev matches @new_class and @new_id, 0 otherwise.
 */
static int ata_dev_same_device(struct ata_device *dev, unsigned int new_class,
			       const u16 *new_id)
{
	const u16 *old_id = dev->id;
	unsigned char model[2][ATA_ID_PROD_LEN + 1];
	unsigned char serial[2][ATA_ID_SERNO_LEN + 1];

	if (dev->class != new_class) {
		ata_dev_info(dev, "class mismatch %d != %d\n",
			     dev->class, new_class);
		return 0;
	}

	ata_id_c_string(old_id, model[0], ATA_ID_PROD, sizeof(model[0]));
	ata_id_c_string(new_id, model[1], ATA_ID_PROD, sizeof(model[1]));
	ata_id_c_string(old_id, serial[0], ATA_ID_SERNO, sizeof(serial[0]));
	ata_id_c_string(new_id, serial[1], ATA_ID_SERNO, sizeof(serial[1]));

	if (strcmp(model[0], model[1])) {
		ata_dev_info(dev, "model number mismatch '%s' != '%s'\n",
			     model[0], model[1]);
		return 0;
	}

	if (strcmp(serial[0], serial[1])) {
		ata_dev_info(dev, "serial number mismatch '%s' != '%s'\n",
			     serial[0], serial[1]);
		return 0;
	}

	return 1;
}

/**
 *	ata_dev_reread_id - Re-read IDENTIFY data
 *	@dev: target ATA device
 *	@readid_flags: read ID flags
 *
 *	Re-read IDENTIFY page and make sure @dev is still attached to
 *	the port.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	0 on success, negative errno otherwise
 */
int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags)
{
	unsigned int class = dev->class;
	u16 *id = (void *)dev->sector_buf;
	int rc;

	/* read ID data */
	rc = ata_dev_read_id(dev, &class, readid_flags, id);
	if (rc)
		return rc;

	/* is the device still there? */
	if (!ata_dev_same_device(dev, class, id))
		return -ENODEV;

	memcpy(dev->id, id, sizeof(id[0]) * ATA_ID_WORDS);
	return 0;
}

/**
 *	ata_dev_revalidate - Revalidate ATA device
 *	@dev: device to revalidate
 *	@new_class: new class code
 *	@readid_flags: read ID flags
 *
 *	Re-read IDENTIFY page, make sure @dev is still attached to the
 *	port and reconfigure it according to the new IDENTIFY page.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	0 on success, negative errno otherwise
 */
int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
		       unsigned int readid_flags)
{
	u64 n_sectors = dev->n_sectors;
	u64 n_native_sectors = dev->n_native_sectors;
	int rc;

	if (!ata_dev_enabled(dev))
		return -ENODEV;

	/* fail early if !ATA && !ATAPI to avoid issuing [P]IDENTIFY to PMP */
	if (ata_class_enabled(new_class) && new_class == ATA_DEV_PMP) {
		ata_dev_info(dev, "class mismatch %u != %u\n",
			     dev->class, new_class);
		rc = -ENODEV;
		goto fail;
	}

	/* re-read ID */
	rc = ata_dev_reread_id(dev, readid_flags);
	if (rc)
		goto fail;

	/* configure device according to the new ID */
	rc = ata_dev_configure(dev);
	if (rc)
		goto fail;

	/* verify n_sectors hasn't changed */
	if (dev->class != ATA_DEV_ATA || !n_sectors ||
	    dev->n_sectors == n_sectors || ata_id_is_locked(dev->id))
		return 0;

	/* n_sectors has changed */
	ata_dev_warn(dev, "n_sectors mismatch %llu != %llu\n",
		     (unsigned long long)n_sectors,
		     (unsigned long long)dev->n_sectors);

	/*
	 * Something could have caused HPA to be unlocked
	 * involuntarily.  If n_native_sectors hasn't changed and the
	 * new size matches it, keep the device.
	 */
	if (dev->n_native_sectors == n_native_sectors &&
	    dev->n_sectors > n_sectors && dev->n_sectors == n_native_sectors) {
		ata_dev_warn(dev,
			     "new n_sectors matches native, probably "
			     "late HPA unlock, n_sectors updated\n");
		/* use the larger n_sectors */
		return 0;
	}

	/*
	 * Some BIOSes boot w/o HPA but resume w/ HPA locked.  Try
	 * unlocking HPA in those cases.
	 *
	 * https://bugzilla.kernel.org/show_bug.cgi?id=15396
	 */
	if (dev->n_native_sectors == n_native_sectors &&
	    dev->n_sectors < n_sectors && n_sectors == n_native_sectors &&
	    !(dev->quirks & ATA_QUIRK_BROKEN_HPA)) {
		ata_dev_warn(dev,
			     "old n_sectors matches native, probably "
			     "late HPA lock, will try to unlock HPA\n");
		/* try unlocking HPA */
		dev->flags |= ATA_DFLAG_UNLOCK_HPA;
		rc = -EIO;
	} else
		rc = -ENODEV;

	/* restore original n_[native_]sectors and fail */
	dev->n_native_sectors = n_native_sectors;
	dev->n_sectors = n_sectors;
 fail:
	ata_dev_err(dev, "revalidation failed (errno=%d)\n", rc);
	return rc;
}

static const char * const ata_quirk_names[] = {
	[__ATA_QUIRK_DIAGNOSTIC]	= "diagnostic",
	[__ATA_QUIRK_NODMA]		= "nodma",
	[__ATA_QUIRK_NONCQ]		= "noncq",
	[__ATA_QUIRK_BROKEN_HPA]	= "brokenhpa",
	[__ATA_QUIRK_DISABLE]		= "disable",
	[__ATA_QUIRK_HPA_SIZE]		= "hpasize",
	[__ATA_QUIRK_IVB]		= "ivb",
	[__ATA_QUIRK_STUCK_ERR]		= "stuckerr",
	[__ATA_QUIRK_BRIDGE_OK]		= "bridgeok",
	[__ATA_QUIRK_ATAPI_MOD16_DMA]	= "atapimod16dma",
	[__ATA_QUIRK_FIRMWARE_WARN]	= "firmwarewarn",
	[__ATA_QUIRK_1_5_GBPS]		= "1.5gbps",
	[__ATA_QUIRK_NOSETXFER]		= "nosetxfer",
	[__ATA_QUIRK_BROKEN_FPDMA_AA]	= "brokenfpdmaaa",
	[__ATA_QUIRK_DUMP_ID]		= "dumpid",
	[__ATA_QUIRK_MAX_SEC_LBA48]	= "maxseclba48",
	[__ATA_QUIRK_ATAPI_DMADIR]	= "atapidmadir",
	[__ATA_QUIRK_NO_NCQ_TRIM]	= "noncqtrim",
	[__ATA_QUIRK_NOLPM]		= "nolpm",
	[__ATA_QUIRK_WD_BROKEN_LPM]	= "wdbrokenlpm",
	[__ATA_QUIRK_ZERO_AFTER_TRIM]	= "zeroaftertrim",
	[__ATA_QUIRK_NO_DMA_LOG]	= "nodmalog",
	[__ATA_QUIRK_NOTRIM]		= "notrim",
	[__ATA_QUIRK_MAX_SEC]		= "maxsec",
	[__ATA_QUIRK_MAX_TRIM_128M]	= "maxtrim128m",
	[__ATA_QUIRK_NO_NCQ_ON_ATI]	= "noncqonati",
	[__ATA_QUIRK_NO_LPM_ON_ATI]	= "nolpmonati",
	[__ATA_QUIRK_NO_ID_DEV_LOG]	= "noiddevlog",
	[__ATA_QUIRK_NO_LOG_DIR]	= "nologdir",
	[__ATA_QUIRK_NO_FUA]		= "nofua",
};

static void ata_dev_print_quirks(const struct ata_device *dev,
				 const char *model, const char *rev,
				 unsigned int quirks)
{
	struct ata_eh_context *ehc = &dev->link->eh_context;
	int n = 0, i;
	size_t sz;
	char *str;

	if (!ata_dev_print_info(dev) || ehc->i.flags & ATA_EHI_DID_PRINT_QUIRKS)
		return;

	ehc->i.flags |= ATA_EHI_DID_PRINT_QUIRKS;

	if (!quirks)
		return;

	sz = 64 + ARRAY_SIZE(ata_quirk_names) * 16;
	str = kmalloc(sz, GFP_KERNEL);
	if (!str)
		return;

	n = snprintf(str, sz, "Model '%s', rev '%s', applying quirks:",
		     model, rev);

	for (i = 0; i < ARRAY_SIZE(ata_quirk_names); i++) {
		if (quirks & (1U << i))
			n += snprintf(str + n, sz - n,
				      " %s", ata_quirk_names[i]);
	}

	ata_dev_warn(dev, "%s\n", str);

	kfree(str);
}

struct ata_dev_quirk_value {
	const char	*model_num;
	const char	*model_rev;
	u64		val;
};

static const struct ata_dev_quirk_value __ata_dev_max_sec_quirks[] = {
	{ "TORiSAN DVD-ROM DRD-N216",	NULL,		128 },
	{ "ST380013AS",			"3.20",		1024 },
	{ "LITEON CX1-JB*-HP",		NULL,		1024 },
	{ "LITEON EP1-*",		NULL,		1024 },
	{ "DELLBOSS VD",		"MV.R00-0",	8191 },
	{ "INTEL SSDSC2KG480G8",	"XCV10120",	8191 },
	{ },
};

struct ata_dev_quirks_entry {
	const char *model_num;
	const char *model_rev;
	u64 quirks;
};

static const struct ata_dev_quirks_entry __ata_dev_quirks[] = {
	/* Devices with DMA related problems under Linux */
	{ "WDC AC11000H",	NULL,		ATA_QUIRK_NODMA },
	{ "WDC AC22100H",	NULL,		ATA_QUIRK_NODMA },
	{ "WDC AC32500H",	NULL,		ATA_QUIRK_NODMA },
	{ "WDC AC33100H",	NULL,		ATA_QUIRK_NODMA },
	{ "WDC AC31600H",	NULL,		ATA_QUIRK_NODMA },
	{ "WDC AC32100H",	"24.09P07",	ATA_QUIRK_NODMA },
	{ "WDC AC23200L",	"21.10N21",	ATA_QUIRK_NODMA },
	{ "Compaq CRD-8241B",	NULL,		ATA_QUIRK_NODMA },
	{ "CRD-8400B",		NULL,		ATA_QUIRK_NODMA },
	{ "CRD-848[02]B",	NULL,		ATA_QUIRK_NODMA },
	{ "CRD-84",		NULL,		ATA_QUIRK_NODMA },
	{ "SanDisk SDP3B",	NULL,		ATA_QUIRK_NODMA },
	{ "SanDisk SDP3B-64",	NULL,		ATA_QUIRK_NODMA },
	{ "SANYO CD-ROM CRD",	NULL,		ATA_QUIRK_NODMA },
	{ "HITACHI CDR-8",	NULL,		ATA_QUIRK_NODMA },
	{ "HITACHI CDR-8[34]35", NULL,		ATA_QUIRK_NODMA },
	{ "Toshiba CD-ROM XM-6202B", NULL,	ATA_QUIRK_NODMA },
	{ "TOSHIBA CD-ROM XM-1702BC", NULL,	ATA_QUIRK_NODMA },
	{ "CD-532E-A",		NULL,		ATA_QUIRK_NODMA },
	{ "E-IDE CD-ROM CR-840", NULL,		ATA_QUIRK_NODMA },
	{ "CD-ROM Drive/F5A",	NULL,		ATA_QUIRK_NODMA },
	{ "WPI CDD-820",	NULL,		ATA_QUIRK_NODMA },
	{ "SAMSUNG CD-ROM SC-148C", NULL,	ATA_QUIRK_NODMA },
	{ "SAMSUNG CD-ROM SC",	NULL,		ATA_QUIRK_NODMA },
	{ "ATAPI CD-ROM DRIVE 40X MAXIMUM", NULL, ATA_QUIRK_NODMA },
	{ "_NEC DV5800A",	NULL,		ATA_QUIRK_NODMA },
	{ "SAMSUNG CD-ROM SN-124", "N001",	ATA_QUIRK_NODMA },
	{ "Seagate STT20000A", NULL,		ATA_QUIRK_NODMA },
	{ " 2GB ATA Flash Disk", "ADMA428M",	ATA_QUIRK_NODMA },
	{ "VRFDFC22048UCHC-TE*", NULL,		ATA_QUIRK_NODMA },
	/* Odd clown on sil3726/4726 PMPs */
	{ "Config  Disk",	NULL,		ATA_QUIRK_DISABLE },
	/* Similar story with ASMedia 1092 */
	{ "ASMT109x- Config",	NULL,		ATA_QUIRK_DISABLE },

	/* Weird ATAPI devices */
	{ "TORiSAN DVD-ROM DRD-N216", NULL,	ATA_QUIRK_MAX_SEC },
	{ "QUANTUM DAT    DAT72-000", NULL,	ATA_QUIRK_ATAPI_MOD16_DMA },
	{ "Slimtype DVD A  DS8A8SH", NULL,	ATA_QUIRK_MAX_SEC_LBA48 },
	{ "Slimtype DVD A  DS8A9SH", NULL,	ATA_QUIRK_MAX_SEC_LBA48 },

	/*
	 * Causes silent data corruption with higher max sects.
	 * http://lkml.kernel.org/g/x49wpy40ysk.fsf@segfault.boston.devel.redhat.com
	 */
	{ "ST380013AS",		"3.20",		ATA_QUIRK_MAX_SEC },

	/*
	 * These devices time out with higher max sects.
	 * https://bugzilla.kernel.org/show_bug.cgi?id=121671
	 */
	{ "LITEON CX1-JB*-HP",	NULL,		ATA_QUIRK_MAX_SEC },
	{ "LITEON EP1-*",	NULL,		ATA_QUIRK_MAX_SEC },

	/*
	 * These devices time out with higher max sects.
	 * https://bugzilla.kernel.org/show_bug.cgi?id=220693
	 */
	{ "DELLBOSS VD",	"MV.R00-0",	ATA_QUIRK_MAX_SEC },

	/* Devices we expect to fail diagnostics */

	/* Devices where NCQ should be avoided */
	/* NCQ is slow */
	{ "WDC WD740ADFD-00",	NULL,		ATA_QUIRK_NONCQ },
	{ "WDC WD740ADFD-00NLR1", NULL,		ATA_QUIRK_NONCQ },
	/* http://thread.gmane.org/gmane.linux.ide/14907 */
	{ "FUJITSU MHT2060BH",	NULL,		ATA_QUIRK_NONCQ },
	/* NCQ is broken */
	{ "Maxtor *",		"BANC*",	ATA_QUIRK_NONCQ },
	{ "Maxtor 7V300F0",	"VA111630",	ATA_QUIRK_NONCQ },
	{ "ST380817AS",		"3.42",		ATA_QUIRK_NONCQ },
	{ "ST3160023AS",	"3.42",		ATA_QUIRK_NONCQ },
	{ "OCZ CORE_SSD",	"02.10104",	ATA_QUIRK_NONCQ },

	/* Seagate NCQ + FLUSH CACHE firmware bug */
	{ "ST31500341AS",	"SD1[5-9]",	ATA_QUIRK_NONCQ |
						ATA_QUIRK_FIRMWARE_WARN },

	{ "ST31000333AS",	"SD1[5-9]",	ATA_QUIRK_NONCQ |
						ATA_QUIRK_FIRMWARE_WARN },

	{ "ST3640[36]23AS",	"SD1[5-9]",	ATA_QUIRK_NONCQ |
						ATA_QUIRK_FIRMWARE_WARN },

	{ "ST3320[68]13AS",	"SD1[5-9]",	ATA_QUIRK_NONCQ |
						ATA_QUIRK_FIRMWARE_WARN },

	/* ADATA devices with LPM issues. */
	{ "ADATA SU680",	NULL,		ATA_QUIRK_NOLPM },

	/* Seagate disks with LPM issues */
	{ "ST1000DM010-2EP102",	NULL,		ATA_QUIRK_NOLPM },
	{ "ST2000DM008-2FR102",	NULL,		ATA_QUIRK_NOLPM },

	/* drives which fail FPDMA_AA activation (some may freeze afterwards)
	   the ST disks also have LPM issues */
	{ "ST1000LM024 HN-M101MBB", NULL,	ATA_QUIRK_BROKEN_FPDMA_AA |
						ATA_QUIRK_NOLPM },
	{ "VB0250EAVER",	"HPG7",		ATA_QUIRK_BROKEN_FPDMA_AA },

	/* Blacklist entries taken from Silicon Image 3124/3132
	   Windows driver .inf file - also several Linux problem reports */
	{ "HTS541060G9SA00",    "MB3OC60D",     ATA_QUIRK_NONCQ },
	{ "HTS541080G9SA00",    "MB4OC60D",     ATA_QUIRK_NONCQ },
	{ "HTS541010G9SA00",    "MBZOC60D",     ATA_QUIRK_NONCQ },

	/* https://bugzilla.kernel.org/show_bug.cgi?id=15573 */
	{ "C300-CTFDDAC128MAG",	"0001",		ATA_QUIRK_NONCQ },

	/* Sandisk SD7/8/9s lock up hard on large trims */
	{ "SanDisk SD[789]*",	NULL,		ATA_QUIRK_MAX_TRIM_128M },

	/* devices which puke on READ_NATIVE_MAX */
	{ "HDS724040KLSA80",	"KFAOA20N",	ATA_QUIRK_BROKEN_HPA },
	{ "WDC WD3200JD-00KLB0", "WD-WCAMR1130137", ATA_QUIRK_BROKEN_HPA },
	{ "WDC WD2500JD-00HBB0", "WD-WMAL71490727", ATA_QUIRK_BROKEN_HPA },
	{ "MAXTOR 6L080L4",	"A93.0500",	ATA_QUIRK_BROKEN_HPA },

	/* this one allows HPA unlocking but fails IOs on the area */
	{ "OCZ-VERTEX",		    "1.30",	ATA_QUIRK_BROKEN_HPA },

	/* Devices which report 1 sector over size HPA */
	{ "ST340823A",		NULL,		ATA_QUIRK_HPA_SIZE },
	{ "ST320413A",		NULL,		ATA_QUIRK_HPA_SIZE },
	{ "ST310211A",		NULL,		ATA_QUIRK_HPA_SIZE },

	/* Devices which get the IVB wrong */
	{ "QUANTUM FIREBALLlct10 05", "A03.0900", ATA_QUIRK_IVB },
	/* Maybe we should just add all TSSTcorp devices... */
	{ "TSSTcorp CDDVDW SH-S202[HJN]", "SB0[01]",  ATA_QUIRK_IVB },

	/* Devices that do not need bridging limits applied */
	{ "MTRON MSP-SATA*",		NULL,	ATA_QUIRK_BRIDGE_OK },
	{ "BUFFALO HD-QSU2/R5",		NULL,	ATA_QUIRK_BRIDGE_OK },
	{ "QEMU HARDDISK",		"2.5+",	ATA_QUIRK_BRIDGE_OK },

	/* Devices which aren't very happy with higher link speeds */
	{ "WD My Book",			NULL,	ATA_QUIRK_1_5_GBPS },
	{ "Seagate FreeAgent GoFlex",	NULL,	ATA_QUIRK_1_5_GBPS },

	/*
	 * Devices which choke on SETXFER.  Applies only if both the
	 * device and controller are SATA.
	 */
	{ "PIONEER DVD-RW  DVRTD08",	NULL,	ATA_QUIRK_NOSETXFER },
	{ "PIONEER DVD-RW  DVRTD08A",	NULL,	ATA_QUIRK_NOSETXFER },
	{ "PIONEER DVD-RW  DVR-215",	NULL,	ATA_QUIRK_NOSETXFER },
	{ "PIONEER DVD-RW  DVR-212D",	NULL,	ATA_QUIRK_NOSETXFER },
	{ "PIONEER DVD-RW  DVR-216D",	NULL,	ATA_QUIRK_NOSETXFER },

	/* These specific Pioneer models have LPM issues */
	{ "PIONEER BD-RW   BDR-207M",	NULL,	ATA_QUIRK_NOLPM },
	{ "PIONEER BD-RW   BDR-205",	NULL,	ATA_QUIRK_NOLPM },

	/* Crucial devices with broken LPM support */
	{ "CT*0BX*00SSD1",		NULL,	ATA_QUIRK_NOLPM },

	/* 512GB MX100 with MU01 firmware has both queued TRIM and LPM issues */
	{ "Crucial_CT512MX100*",	"MU01",	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NOLPM },
	/* 512GB MX100 with newer firmware has only LPM issues */
	{ "Crucial_CT512MX100*",	NULL,	ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NOLPM },

	/* 480GB+ M500 SSDs have both queued TRIM and LPM issues */
	{ "Crucial_CT480M500*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NOLPM },
	{ "Crucial_CT960M500*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NOLPM },

	/* AMD Radeon devices with broken LPM support */
	{ "R3SL240G",			NULL,	ATA_QUIRK_NOLPM },

	/* Apacer models with LPM issues */
	{ "Apacer AS340*",		NULL,	ATA_QUIRK_NOLPM },

	/* PNY CS900 (Phison PS3111-S11, DRAM-less) drops the link on DIPM */
	{ "PNY CS900 1TB SSD",		NULL,	ATA_QUIRK_NOLPM },

	/* Silicon Motion models with LPM issues */
	{ "MD619HXCLDE3TC",		"TCVAID", ATA_QUIRK_NOLPM },
	{ "MD619GXCLDE3TC",		"TCV35D", ATA_QUIRK_NOLPM },

	/* These specific Samsung models/firmware-revs do not handle LPM well */
	{ "SAMSUNG MZMPC128HBFU-000MV", "CXM14M1Q", ATA_QUIRK_NOLPM },
	{ "SAMSUNG SSD PM830 mSATA *",  "CXM13D1Q", ATA_QUIRK_NOLPM },
	{ "SAMSUNG MZ7TD256HAFV-000L9", NULL,       ATA_QUIRK_NOLPM },
	{ "SAMSUNG MZ7TE512HMHP-000L1", "EXT06L0Q", ATA_QUIRK_NOLPM },

	/* devices that don't properly handle queued TRIM commands */
	{ "Micron_M500IT_*",		"MU01",	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Micron_M500_*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Micron_M5[15]0_*",		"MU01",	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Micron_1100_*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM, },
	{ "Crucial_CT*M500*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Crucial_CT*M550*",		"MU01",	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Crucial_CT*MX100*",		"MU01",	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Samsung SSD 840 EVO*",	NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_NO_DMA_LOG |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Samsung SSD 840*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Samsung SSD 850*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Samsung SSD 860*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NO_NCQ_ON_ATI |
						ATA_QUIRK_NO_LPM_ON_ATI },
	{ "Samsung SSD 870*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NO_NCQ_ON_ATI |
						ATA_QUIRK_NO_LPM_ON_ATI },
	{ "SAMSUNG*MZ7LH*",		NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_NO_NCQ_ON_ATI |
						ATA_QUIRK_NO_LPM_ON_ATI },
	{ "FCCT*M500*",			NULL,	ATA_QUIRK_NO_NCQ_TRIM |
						ATA_QUIRK_ZERO_AFTER_TRIM },

	/* devices that don't properly handle TRIM commands */
	{ "SuperSSpeed S238*",		NULL,	ATA_QUIRK_NOTRIM },
	{ "M88V29*",			NULL,	ATA_QUIRK_NOTRIM },

	/*
	 * As defined, the DRAT (Deterministic Read After Trim) and RZAT
	 * (Return Zero After Trim) flags in the ATA Command Set are
	 * unreliable in the sense that they only define what happens if
	 * the device successfully executed the DSM TRIM command. TRIM
	 * is only advisory, however, and the device is free to silently
	 * ignore all or parts of the request.
	 *
	 * Whitelist drives that are known to reliably return zeroes
	 * after TRIM.
	 */

	/*
	 * The intel 510 drive has buggy DRAT/RZAT. Explicitly exclude
	 * that model before whitelisting all other intel SSDs.
	 */
	{ "INTEL*SSDSC2MH*",		NULL,	0 },

	{ "Micron*",			NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Crucial*",			NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "INTEL SSDSC2KG480G8", "XCV10120",	ATA_QUIRK_ZERO_AFTER_TRIM |
						ATA_QUIRK_MAX_SEC },
	{ "INTEL*SSD*",			NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "SSD*INTEL*",			NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "Samsung*SSD*",		NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "SAMSUNG*SSD*",		NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "SAMSUNG*MZ7KM*",		NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },
	{ "ST[1248][0248]0[FH]*",	NULL,	ATA_QUIRK_ZERO_AFTER_TRIM },

	/*
	 * Some WD SATA-I drives spin up and down erratically when the link
	 * is put into the slumber mode.  We don't have full list of the
	 * affected devices.  Disable LPM if the device matches one of the
	 * known prefixes and is SATA-1.  As a side effect LPM partial is
	 * lost too.
	 *
	 * https://bugzilla.kernel.org/show_bug.cgi?id=57211
	 */
	{ "WDC WD800JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD1200JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD1600JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD2000JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD2500JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD3000JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },
	{ "WDC WD3200JD-*",		NULL,	ATA_QUIRK_WD_BROKEN_LPM },

	/*
	 * WD drives with LPM issues (irrespective of supported SATA speeds).
	 * (Unlike ATA_QUIRK_WD_BROKEN_LPM, which is only applied if the drive
	 * exposes SATA Gen1 speed support, and SATA Gen1 speed support only.)
	 */
	{ "WDC WD100EFGX-68CPLN0",	NULL,	ATA_QUIRK_NOLPM },
	{ "WDC WD102KFBX-68M95N0",	NULL,	ATA_QUIRK_NOLPM },
	{ "WDC WD141KFGX-68FH9N0",	NULL,	ATA_QUIRK_NOLPM },
	{ "WD Green 2.5 480GB",		NULL,	ATA_QUIRK_NOLPM },

	/*
	 * This sata dom device goes on a walkabout when the ATA_LOG_DIRECTORY
	 * log page is accessed. Ensure we never ask for this log page with
	 * these devices.
	 */
	{ "SATADOM-ML 3ME",		NULL,	ATA_QUIRK_NO_LOG_DIR },

	/* Buggy FUA */
	{ "Maxtor",		"BANC1G10",	ATA_QUIRK_NO_FUA },
	{ "WDC*WD2500J*",	NULL,		ATA_QUIRK_NO_FUA },
	{ "OCZ-VERTEX*",	NULL,		ATA_QUIRK_NO_FUA },
	{ "INTEL*SSDSC2CT*",	NULL,		ATA_QUIRK_NO_FUA },

	/* End Marker */
	{ }
};

static u64 ata_dev_quirks(const struct ata_device *dev)
{
	unsigned char model_num[ATA_ID_PROD_LEN + 1];
	unsigned char model_rev[ATA_ID_FW_REV_LEN + 1];
	const struct ata_dev_quirks_entry *ad = __ata_dev_quirks;

	/* dev->quirks is an u64. */
	BUILD_BUG_ON(__ATA_QUIRK_MAX > 64);

	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
	ata_id_c_string(dev->id, model_rev, ATA_ID_FW_REV, sizeof(model_rev));

	while (ad->model_num) {
		if (glob_match(ad->model_num, model_num) &&
		    (!ad->model_rev || glob_match(ad->model_rev, model_rev))) {
			ata_dev_print_quirks(dev, model_num, model_rev,
					     ad->quirks);
			return ad->quirks;
		}
		ad++;
	}
	return 0;
}

static u64 ata_dev_get_max_sec_quirk_value(struct ata_device *dev)
{
	unsigned char model_num[ATA_ID_PROD_LEN + 1];
	unsigned char model_rev[ATA_ID_FW_REV_LEN + 1];
	const struct ata_dev_quirk_value *ad = __ata_dev_max_sec_quirks;
	u64 val = 0;

#ifdef CONFIG_ATA_FORCE
	const struct ata_force_ent *fe = ata_force_get_fe_for_dev(dev);
	if (fe && (fe->param.quirk_on & ATA_QUIRK_MAX_SEC) && fe->param.value)
		val = fe->param.value;
#endif
	if (val)
		goto out;

	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
	ata_id_c_string(dev->id, model_rev, ATA_ID_FW_REV, sizeof(model_rev));

	while (ad->model_num) {
		if (glob_match(ad->model_num, model_num) &&
		    (!ad->model_rev || glob_match(ad->model_rev, model_rev))) {
			val = ad->val;
			break;
		}
		ad++;
	}

out:
	ata_dev_warn(dev, "%s quirk is using value: %llu\n",
		     ata_quirk_names[__ATA_QUIRK_MAX_SEC], val);

	return val;
}

static u64 ata_dev_get_quirk_value(struct ata_device *dev, u64 quirk)
{
	if (quirk == ATA_QUIRK_MAX_SEC)
		return ata_dev_get_max_sec_quirk_value(dev);

	return 0;
}

static bool ata_dev_nodma(const struct ata_device *dev)
{
	/*
	 * We do not support polling DMA. Deny DMA for those ATAPI devices
	 * with CDB-intr (and use PIO) if the LLDD handles only interrupts in
	 * the HSM_ST_LAST state.
	 */
	if ((dev->link->ap->flags & ATA_FLAG_PIO_POLLING) &&
	    (dev->flags & ATA_DFLAG_CDB_INTR))
		return true;
	return dev->quirks & ATA_QUIRK_NODMA;
}

/**
 *	ata_is_40wire		-	check drive side detection
 *	@dev: device
 *
 *	Perform drive side detection decoding, allowing for device vendors
 *	who can't follow the documentation.
 */

static int ata_is_40wire(struct ata_device *dev)
{
	if (dev->quirks & ATA_QUIRK_IVB)
		return ata_drive_40wire_relaxed(dev->id);
	return ata_drive_40wire(dev->id);
}

/**
 *	cable_is_40wire		-	40/80/SATA decider
 *	@ap: port to consider
 *
 *	This function encapsulates the policy for speed management
 *	in one place. At the moment we don't cache the result but
 *	there is a good case for setting ap->cbl to the result when
 *	we are called with unknown cables (and figuring out if it
 *	impacts hotplug at all).
 *
 *	Return 1 if the cable appears to be 40 wire.
 */

static int cable_is_40wire(struct ata_port *ap)
{
	struct ata_link *link;
	struct ata_device *dev;

	/* If the controller thinks we are 40 wire, we are. */
	if (ap->cbl == ATA_CBL_PATA40)
		return 1;

	/* If the controller thinks we are 80 wire, we are. */
	if (ap->cbl == ATA_CBL_PATA80 || ap->cbl == ATA_CBL_SATA)
		return 0;

	/* If the system is known to be 40 wire short cable (eg
	 * laptop), then we allow 80 wire modes even if the drive
	 * isn't sure.
	 */
	if (ap->cbl == ATA_CBL_PATA40_SHORT)
		return 0;

	/* If the controller doesn't know, we scan.
	 *
	 * Note: We look for all 40 wire detects at this point.  Any
	 *       80 wire detect is taken to be 80 wire cable because
	 * - in many setups only the one drive (slave if present) will
	 *   give a valid detect
	 * - if you have a non detect capable drive you don't want it
	 *   to colour the choice
	 */
	ata_for_each_link(link, ap, EDGE) {
		ata_for_each_dev(dev, link, ENABLED) {
			if (!ata_is_40wire(dev))
				return 0;
		}
	}
	return 1;
}

/**
 *	ata_dev_xfermask - Compute supported xfermask of the given device
 *	@dev: Device to compute xfermask for
 *
 *	Compute supported xfermask of @dev and store it in
 *	dev->*_mask.  This function is responsible for applying all
 *	known limits including host controller limits, device quirks, etc...
 *
 *	LOCKING:
 *	None.
 */
static void ata_dev_xfermask(struct ata_device *dev)
{
	struct ata_link *link = dev->link;
	struct ata_port *ap = link->ap;
	struct ata_host *host = ap->host;
	unsigned int xfer_mask;

	/* controller modes available */
	xfer_mask = ata_pack_xfermask(ap->pio_mask,
				      ap->mwdma_mask, ap->udma_mask);

	/* drive modes available */
	xfer_mask &= ata_pack_xfermask(dev->pio_mask,
				       dev->mwdma_mask, dev->udma_mask);
	xfer_mask &= ata_id_xfermask(dev->id);

	/*
	 *	CFA Advanced TrueIDE timings are not allowed on a shared
	 *	cable
	 */
	if (ata_dev_pair(dev)) {
		/* No PIO5 or PIO6 */
		xfer_mask &= ~(0x03 << (ATA_SHIFT_PIO + 5));
		/* No MWDMA3 or MWDMA 4 */
		xfer_mask &= ~(0x03 << (ATA_SHIFT_MWDMA + 3));
	}

	if (ata_dev_nodma(dev)) {
		xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
		ata_dev_warn(dev,
			     "device does not support DMA, disabling DMA\n");
	}

	if ((host->flags & ATA_HOST_SIMPLEX) &&
	    host->simplex_claimed && host->simplex_claimed != ap) {
		xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
		ata_dev_warn(dev,
			     "simplex DMA is claimed by other device, disabling DMA\n");
	}

	if (ap->flags & ATA_FLAG_NO_IORDY)
		xfer_mask &= ata_pio_mask_no_iordy(dev);

	if (ap->ops->mode_filter)
		xfer_mask = ap->ops->mode_filter(dev, xfer_mask);

	/* Apply cable rule here.  Don't apply it early because when
	 * we handle hot plug the cable type can itself change.
	 * Check this last so that we know if the transfer rate was
	 * solely limited by the cable.
	 * Unknown or 80 wire cables reported host side are checked
	 * drive side as well. Cases where we know a 40wire cable
	 * is used safely for 80 are not checked here.
	 */
	if (xfer_mask & (0xF8 << ATA_SHIFT_UDMA))
		/* UDMA/44 or higher would be available */
		if (cable_is_40wire(ap)) {
			ata_dev_warn(dev,
				     "limited to UDMA/33 due to 40-wire cable\n");
			xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
		}

	ata_unpack_xfermask(xfer_mask, &dev->pio_mask,
			    &dev->mwdma_mask, &dev->udma_mask);
}

/**
 *	ata_dev_set_xfermode - Issue SET FEATURES - XFER MODE command
 *	@dev: Device to which command will be sent
 *
 *	Issue SET FEATURES - XFER MODE command to device @dev
 *	on port @ap.
 *
 *	LOCKING:
 *	PCI/etc. bus probe sem.
 *
 *	RETURNS:
 *	0 on success, AC_ERR_* mask otherwise.
 */

static unsigned int ata_dev_set_xfermode(struct ata_device *dev)
{
	struct ata_taskfile tf;

	/* set up set-features taskfile */
	ata_dev_dbg(dev, "set features - xfer mode\n");

	/* Some controllers and ATAPI devices show flaky interrupt
	 * behavior after setting xfer mode.  Use polling instead.
	 */
	ata_tf_init(dev, &tf);
	tf.command = ATA_CMD_SET_FEATURES;
	tf.feature = SETFEATURES_XFER;
	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE | ATA_TFLAG_POLLING;
	tf.protocol = ATA_PROT_NODATA;
	/* If we are using IORDY we must send the mode setting command */
	if (ata_pio_need_iordy(dev))
		tf.nsect = dev->xfer_mode;
	/* If the device has IORDY and the controller does not - turn it off */
 	else if (ata_id_has_iordy(dev->id))
		tf.nsect = 0x01;
	else /* In the ancient relic department - skip all of this */
		return 0;

	/*
	 * On some disks, this command causes spin-up, so we need longer
	 * timeout.
	 */
	return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 15000);
}

/**
 *	ata_dev_set_feature - Issue SET FEATURES
 *	@dev: Device to which command will be sent
 *	@subcmd: The SET FEATURES subcommand to be sent
 *	@action: The sector count represents a subcommand specific action
 *
 *	Issue SET FEATURES command to device @dev on port @ap with sector count
 *
 *	LOCKING:
 *	PCI/etc. bus probe sem.
 *
 *	RETURNS:
 *	0 on success, AC_ERR_* mask otherwise.
 */
unsigned int ata_dev_set_feature(struct ata_device *dev, u8 subcmd, u8 action)
{
	struct ata_taskfile tf;
	unsigned int timeout = 0;

	/* set up set-features taskfile */
	ata_dev_dbg(dev, "set features\n");

	ata_tf_init(dev, &tf);
	tf.command = ATA_CMD_SET_FEATURES;
	tf.feature = subcmd;
	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
	tf.protocol = ATA_PROT_NODATA;
	tf.nsect = action;

	if (subcmd == SETFEATURES_SPINUP)
		timeout = ata_probe_timeout ?
			  ata_probe_timeout * 1000 : SETFEATURES_SPINUP_TIMEOUT;

	return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, timeout);
}
EXPORT_SYMBOL_GPL(ata_dev_set_feature);

/**
 *	ata_dev_init_params - Issue INIT DEV PARAMS command
 *	@dev: Device to which command will be sent
 *	@heads: Number of heads (taskfile parameter)
 *	@sectors: Number of sectors (taskfile parameter)
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	0 on success, AC_ERR_* mask otherwise.
 */
static unsigned int ata_dev_init_params(struct ata_device *dev,
					u16 heads, u16 sectors)
{
	struct ata_taskfile tf;
	unsigned int err_mask;

	/* Number of sectors per track 1-255. Number of heads 1-16 */
	if (sectors < 1 || sectors > 255 || heads < 1 || heads > 16)
		return AC_ERR_INVALID;

	/* set up init dev params taskfile */
	ata_dev_dbg(dev, "init dev params\n");

	ata_tf_init(dev, &tf);
	tf.command = ATA_CMD_INIT_DEV_PARAMS;
	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
	tf.protocol = ATA_PROT_NODATA;
	tf.nsect = sectors;
	tf.device |= (heads - 1) & 0x0f; /* max head = num. of heads - 1 */

	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
	/* A clean abort indicates an original or just out of spec drive
	   and we should continue as we issue the setup based on the
	   drive reported working geometry */
	if (err_mask == AC_ERR_DEV && (tf.error & ATA_ABORTED))
		err_mask = 0;

	return err_mask;
}

/**
 *	atapi_check_dma - Check whether ATAPI DMA can be supported
 *	@qc: Metadata associated with taskfile to check
 *
 *	Allow low-level driver to filter ATA PACKET commands, returning
 *	a status indicating whether or not it is OK to use DMA for the
 *	supplied PACKET command.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 *
 *	RETURNS: 0 when ATAPI DMA can be used
 *               nonzero otherwise
 */
int atapi_check_dma(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	/* Don't allow DMA if it isn't multiple of 16 bytes.  Quite a
	 * few ATAPI devices choke on such DMA requests.
	 */
	if (!(qc->dev->quirks & ATA_QUIRK_ATAPI_MOD16_DMA) &&
	    unlikely(qc->nbytes & 15))
		return -EOPNOTSUPP;

	if (ap->ops->check_atapi_dma)
		return ap->ops->check_atapi_dma(qc);

	return 0;
}

/**
 *	ata_std_qc_defer - Check whether a qc needs to be deferred
 *	@qc: ATA command in question
 *
 *	Non-NCQ commands cannot run with any other command, NCQ or
 *	not.  As upper layer only knows the queue depth, we are
 *	responsible for maintaining exclusion.  This function checks
 *	whether a new command @qc can be issued.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 *
 *	RETURNS:
 *	ATA_DEFER_* if deferring is needed, 0 otherwise.
 */
int ata_std_qc_defer(struct ata_queued_cmd *qc)
{
	struct ata_link *link = qc->dev->link;

	if (ata_is_ncq(qc->tf.protocol)) {
		if (!ata_tag_valid(link->active_tag))
			return 0;
	} else {
		if (!ata_tag_valid(link->active_tag) && !link->sactive)
			return 0;
	}

	return ATA_DEFER_LINK;
}
EXPORT_SYMBOL_GPL(ata_std_qc_defer);

/**
 *	ata_sg_init - Associate command with scatter-gather table.
 *	@qc: Command to be associated
 *	@sg: Scatter-gather table.
 *	@n_elem: Number of elements in s/g table.
 *
 *	Initialize the data-related elements of queued_cmd @qc
 *	to point to a scatter-gather table @sg, containing @n_elem
 *	elements.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 */
void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
		 unsigned int n_elem)
{
	qc->sg = sg;
	qc->n_elem = n_elem;
	qc->cursg = qc->sg;
}

#ifdef CONFIG_HAS_DMA

/**
 *	ata_sg_clean - Unmap DMA memory associated with command
 *	@qc: Command containing DMA memory to be released
 *
 *	Unmap all mapped DMA memory associated with this command.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 */
static void ata_sg_clean(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	struct scatterlist *sg = qc->sg;
	int dir = qc->dma_dir;

	WARN_ON_ONCE(sg == NULL);

	if (qc->n_elem)
		dma_unmap_sg(ap->dev, sg, qc->orig_n_elem, dir);

	qc->flags &= ~ATA_QCFLAG_DMAMAP;
	qc->sg = NULL;
}

/**
 *	ata_sg_setup - DMA-map the scatter-gather table associated with a command.
 *	@qc: Command with scatter-gather table to be mapped.
 *
 *	DMA-map the scatter-gather table associated with queued_cmd @qc.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 *
 *	RETURNS:
 *	Zero on success, negative on error.
 *
 */
static int ata_sg_setup(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	unsigned int n_elem;

	n_elem = dma_map_sg(ap->dev, qc->sg, qc->n_elem, qc->dma_dir);
	if (n_elem < 1)
		return -1;

	qc->orig_n_elem = qc->n_elem;
	qc->n_elem = n_elem;
	qc->flags |= ATA_QCFLAG_DMAMAP;

	return 0;
}

#else /* !CONFIG_HAS_DMA */

static inline void ata_sg_clean(struct ata_queued_cmd *qc) {}
static inline int ata_sg_setup(struct ata_queued_cmd *qc) { return -1; }

#endif /* !CONFIG_HAS_DMA */

/**
 *	swap_buf_le16 - swap halves of 16-bit words in place
 *	@buf:  Buffer to swap
 *	@buf_words:  Number of 16-bit words in buffer.
 *
 *	Swap halves of 16-bit words if needed to convert from
 *	little-endian byte order to native cpu byte order, or
 *	vice-versa.
 *
 *	LOCKING:
 *	Inherited from caller.
 */
void swap_buf_le16(u16 *buf, unsigned int buf_words)
{
#ifdef __BIG_ENDIAN
	unsigned int i;

	for (i = 0; i < buf_words; i++)
		buf[i] = le16_to_cpu(buf[i]);
#endif /* __BIG_ENDIAN */
}

/**
 *	ata_qc_free - free unused ata_queued_cmd
 *	@qc: Command to complete
 *
 *	Designed to free unused ata_queued_cmd object
 *	in case something prevents using it.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 */
void ata_qc_free(struct ata_queued_cmd *qc)
{
	qc->flags = 0;
	if (ata_tag_valid(qc->tag))
		qc->tag = ATA_TAG_POISON;
}

void __ata_qc_complete(struct ata_queued_cmd *qc)
{
	struct ata_port *ap;
	struct ata_link *link;

	if (WARN_ON_ONCE(!(qc->flags & ATA_QCFLAG_ACTIVE)))
		return;

	ap = qc->ap;
	link = qc->dev->link;

	if (likely(qc->flags & ATA_QCFLAG_DMAMAP))
		ata_sg_clean(qc);

	/* command should be marked inactive atomically with qc completion */
	if (ata_is_ncq(qc->tf.protocol)) {
		link->sactive &= ~(1 << qc->hw_tag);
		if (!link->sactive)
			ap->nr_active_links--;
	} else {
		link->active_tag = ATA_TAG_POISON;
		ap->nr_active_links--;
	}

	/* clear exclusive status */
	if (unlikely(qc->flags & ATA_QCFLAG_CLEAR_EXCL &&
		     ap->excl_link == link))
		ap->excl_link = NULL;

	/*
	 * Mark qc as inactive to prevent the port interrupt handler from
	 * completing the command twice later, before the error handler is
	 * called.
	 */
	qc->flags &= ~ATA_QCFLAG_ACTIVE;
	ap->qc_active &= ~(1ULL << qc->tag);

	/* call completion callback */
	qc->complete_fn(qc);
}

static void fill_result_tf(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	/*
	 * rtf may already be filled (e.g. for successful NCQ commands).
	 * If that is the case, we have nothing to do.
	 */
	if (qc->flags & ATA_QCFLAG_RTF_FILLED)
		return;

	qc->result_tf.flags = qc->tf.flags;
	ap->ops->qc_fill_rtf(qc);
	qc->flags |= ATA_QCFLAG_RTF_FILLED;
}

static void ata_verify_xfer(struct ata_queued_cmd *qc)
{
	struct ata_device *dev = qc->dev;

	if (!ata_is_data(qc->tf.protocol))
		return;

	if ((dev->mwdma_mask || dev->udma_mask) && ata_is_pio(qc->tf.protocol))
		return;

	dev->flags &= ~ATA_DFLAG_DUBIOUS_XFER;
}

/**
 *	ata_qc_complete - Complete an active ATA command
 *	@qc: Command to complete
 *
 *	Indicate to the mid and upper layers that an ATA command has
 *	completed, with either an ok or not-ok status.
 *
 *	Refrain from calling this function multiple times when
 *	successfully completing multiple NCQ commands.
 *	ata_qc_complete_multiple() should be used instead, which will
 *	properly update IRQ expect state.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 */
void ata_qc_complete(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	struct ata_device *dev = qc->dev;
	struct ata_eh_info *ehi = &dev->link->eh_info;

	/* Trigger the LED (if available) */
	ledtrig_disk_activity(!!(qc->tf.flags & ATA_TFLAG_WRITE));

	/*
	 * In order to synchronize EH with the regular execution path, a qc that
	 * is owned by EH is marked with ATA_QCFLAG_EH.
	 *
	 * The normal execution path is responsible for not accessing a qc owned
	 * by EH.  libata core enforces the rule by returning NULL from
	 * ata_qc_from_tag() for qcs owned by EH.
	 */
	if (unlikely(qc->err_mask))
		qc->flags |= ATA_QCFLAG_EH;

	/*
	 * Finish internal commands without any further processing and always
	 * with the result TF filled.
	 */
	if (unlikely(ata_tag_internal(qc->tag))) {
		fill_result_tf(qc);
		trace_ata_qc_complete_internal(qc);
		__ata_qc_complete(qc);
		return;
	}

	/* Non-internal qc has failed.  Fill the result TF and summon EH. */
	if (unlikely(qc->flags & ATA_QCFLAG_EH)) {
		fill_result_tf(qc);
		trace_ata_qc_complete_failed(qc);
		ata_qc_schedule_eh(qc);
		return;
	}

	WARN_ON_ONCE(ata_port_is_frozen(ap));

	/* read result TF if requested */
	if (qc->flags & ATA_QCFLAG_RESULT_TF)
		fill_result_tf(qc);

	trace_ata_qc_complete_done(qc);

	/*
	 * For CDL commands that completed without an error, check if we have
	 * sense data (ATA_SENSE is set). If we do, then the command may have
	 * been aborted by the device due to a limit timeout using the policy
	 * 0xD. For these commands, invoke EH to get the command sense data.
	 */
	if (qc->flags & ATA_QCFLAG_HAS_CDL &&
	    qc->result_tf.status & ATA_SENSE) {
		/*
		 * Tell SCSI EH to not overwrite scmd->result even if this
		 * command is finished with result SAM_STAT_GOOD.
		 */
		qc->scsicmd->flags |= SCMD_FORCE_EH_SUCCESS;
		qc->flags |= ATA_QCFLAG_EH_SUCCESS_CMD;
		ehi->dev_action[dev->devno] |= ATA_EH_GET_SUCCESS_SENSE;

		/*
		 * set pending so that ata_qc_schedule_eh() does not trigger
		 * fast drain, and freeze the port.
		 */
		ap->pflags |= ATA_PFLAG_EH_PENDING;
		ata_qc_schedule_eh(qc);
		return;
	}

	/* Some commands need post-processing after successful completion. */
	switch (qc->tf.command) {
	case ATA_CMD_SET_FEATURES:
		if (qc->tf.feature != SETFEATURES_WC_ON &&
		    qc->tf.feature != SETFEATURES_WC_OFF &&
		    qc->tf.feature != SETFEATURES_RA_ON &&
		    qc->tf.feature != SETFEATURES_RA_OFF)
			break;
		fallthrough;
	case ATA_CMD_INIT_DEV_PARAMS: /* CHS translation changed */
	case ATA_CMD_SET_MULTI: /* multi_count changed */
		/* revalidate device */
		ehi->dev_action[dev->devno] |= ATA_EH_REVALIDATE;
		ata_port_schedule_eh(ap);
		break;

	case ATA_CMD_SLEEP:
		dev->flags |= ATA_DFLAG_SLEEPING;
		break;
	}

	if (unlikely(dev->flags & ATA_DFLAG_DUBIOUS_XFER))
		ata_verify_xfer(qc);

	__ata_qc_complete(qc);
}
EXPORT_SYMBOL_GPL(ata_qc_complete);

/**
 *	ata_qc_get_active - get bitmask of active qcs
 *	@ap: port in question
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 *
 *	RETURNS:
 *	Bitmask of active qcs
 */
u64 ata_qc_get_active(struct ata_port *ap)
{
	u64 qc_active = ap->qc_active;

	/* ATA_TAG_INTERNAL is sent to hw as tag 0 */
	if (qc_active & (1ULL << ATA_TAG_INTERNAL)) {
		qc_active |= (1 << 0);
		qc_active &= ~(1ULL << ATA_TAG_INTERNAL);
	}

	return qc_active;
}
EXPORT_SYMBOL_GPL(ata_qc_get_active);

/**
 *	ata_qc_issue - issue taskfile to device
 *	@ap: ATA port of interest
 *	@qc: command to issue to device
 *
 *	Prepare an ATA command to submission to device.
 *	This includes mapping the data into a DMA-able
 *	area, filling in the S/G table, and finally
 *	writing the taskfile to hardware, starting the command.
 *
 *	LOCKING:
 *	spin_lock_irqsave(host lock)
 */
void ata_qc_issue(struct ata_port *ap, struct ata_queued_cmd *qc)
	__must_hold(ap->lock)
{
	struct ata_link *link = qc->dev->link;
	u8 prot = qc->tf.protocol;

	/*
	 * Make sure we have a valid tag and that only one non-NCQ command is
	 * outstanding.
	 */
	if (WARN_ON_ONCE(!ata_tag_valid(qc->tag)) ||
	    WARN_ON_ONCE(ata_tag_valid(link->active_tag)))
		goto sys_err;

	if (ata_is_ncq(prot)) {
		WARN_ON_ONCE(link->sactive & (1 << qc->hw_tag));

		if (!link->sactive)
			ap->nr_active_links++;
		link->sactive |= 1 << qc->hw_tag;
	} else {
		WARN_ON_ONCE(link->sactive);

		ap->nr_active_links++;
		link->active_tag = qc->tag;
	}

	qc->flags |= ATA_QCFLAG_ACTIVE;
	ap->qc_active |= 1ULL << qc->tag;

	/* Make sure the device is still accessible. */
	if (!ata_adapter_is_online(ap)) {
		qc->err_mask |= AC_ERR_HOST_BUS;
		goto sys_err;
	}

	/*
	 * We guarantee to LLDs that they will have at least one
	 * non-zero sg if the command is a data command.
	 */
	if (ata_is_data(prot) && (!qc->sg || !qc->n_elem || !qc->nbytes))
		goto sys_err;

	if (ata_is_dma(prot) || (ata_is_pio(prot) &&
				 (ap->flags & ATA_FLAG_PIO_DMA)))
		if (ata_sg_setup(qc))
			goto sys_err;

	/* if device is sleeping, schedule reset and abort the link */
	if (unlikely(qc->dev->flags & ATA_DFLAG_SLEEPING)) {
		link->eh_info.action |= ATA_EH_RESET;
		ata_ehi_push_desc(&link->eh_info, "waking up from sleep");
		ata_link_abort(link);
		return;
	}

	if (ap->ops->qc_prep) {
		trace_ata_qc_prep(qc);
		qc->err_mask |= ap->ops->qc_prep(qc);
		if (unlikely(qc->err_mask))
			goto err;
	}

	trace_ata_qc_issue(qc);
	qc->err_mask |= ap->ops->qc_issue(qc);
	if (unlikely(qc->err_mask))
		goto err;
	return;

sys_err:
	qc->err_mask |= AC_ERR_SYSTEM;
err:
	ata_qc_complete(qc);
}

/**
 *	ata_phys_link_online - test whether the given link is online
 *	@link: ATA link to test
 *
 *	Test whether @link is online.  Note that this function returns
 *	0 if online status of @link cannot be obtained, so
 *	ata_link_online(link) != !ata_link_offline(link).
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	True if the port online status is available and online.
 */
bool ata_phys_link_online(struct ata_link *link)
{
	u32 sstatus;

	if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 &&
	    ata_sstatus_online(sstatus))
		return true;
	return false;
}

/**
 *	ata_phys_link_offline - test whether the given link is offline
 *	@link: ATA link to test
 *
 *	Test whether @link is offline.  Note that this function
 *	returns 0 if offline status of @link cannot be obtained, so
 *	ata_link_online(link) != !ata_link_offline(link).
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	True if the port offline status is available and offline.
 */
bool ata_phys_link_offline(struct ata_link *link)
{
	u32 sstatus;

	if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 &&
	    !ata_sstatus_online(sstatus))
		return true;
	return false;
}

/**
 *	ata_link_online - test whether the given link is online
 *	@link: ATA link to test
 *
 *	Test whether @link is online.  This is identical to
 *	ata_phys_link_online() when there's no slave link.  When
 *	there's a slave link, this function should only be called on
 *	the master link and will return true if any of M/S links is
 *	online.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	True if the port online status is available and online.
 */
bool ata_link_online(struct ata_link *link)
{
	struct ata_link *slave = link->ap->slave_link;

	WARN_ON(link == slave);	/* shouldn't be called on slave link */

	return ata_phys_link_online(link) ||
		(slave && ata_phys_link_online(slave));
}
EXPORT_SYMBOL_GPL(ata_link_online);

/**
 *	ata_link_offline - test whether the given link is offline
 *	@link: ATA link to test
 *
 *	Test whether @link is offline.  This is identical to
 *	ata_phys_link_offline() when there's no slave link.  When
 *	there's a slave link, this function should only be called on
 *	the master link and will return true if both M/S links are
 *	offline.
 *
 *	LOCKING:
 *	None.
 *
 *	RETURNS:
 *	True if the port offline status is available and offline.
 */
bool ata_link_offline(struct ata_link *link)
{
	struct ata_link *slave = link->ap->slave_link;

	WARN_ON(link == slave);	/* shouldn't be called on slave link */

	return ata_phys_link_offline(link) &&
		(!slave || ata_phys_link_offline(slave));
}
EXPORT_SYMBOL_GPL(ata_link_offline);

#ifdef CONFIG_PM
static void ata_port_request_pm(struct ata_port *ap, pm_message_t mesg,
				unsigned int action, unsigned int ehi_flags,
				bool async)
{
	struct ata_link *link;
	unsigned long flags;

	spin_lock_irqsave(ap->lock, flags);

	/*
	 * A previous PM operation might still be in progress. Wait for
	 * ATA_PFLAG_PM_PENDING to clear.
	 */
	if (ap->pflags & ATA_PFLAG_PM_PENDING) {
		spin_unlock_irqrestore(ap->lock, flags);
		ata_port_wait_eh(ap);
		spin_lock_irqsave(ap->lock, flags);
	}

	/* Request PM operation to EH */
	ap->pm_mesg = mesg;
	ap->pflags |= ATA_PFLAG_PM_PENDING;
	ata_for_each_link(link, ap, HOST_FIRST) {
		link->eh_info.action |= action;
		link->eh_info.flags |= ehi_flags;
	}

	ata_port_schedule_eh(ap);

	spin_unlock_irqrestore(ap->lock, flags);

	if (!async)
		ata_port_wait_eh(ap);
}

static void ata_port_suspend(struct ata_port *ap, pm_message_t mesg,
			     bool async)
{
	/*
	 * We are about to suspend the port, so we do not care about
	 * scsi_rescan_device() calls scheduled by previous resume operations.
	 * The next resume will schedule the rescan again. So cancel any rescan
	 * that is not done yet.
	 */
	cancel_delayed_work_sync(&ap->scsi_rescan_task);

	/*
	 * On some hardware, device fails to respond after spun down for
	 * suspend. As the device will not be used until being resumed, we
	 * do not need to touch the device. Ask EH to skip the usual stuff
	 * and proceed directly to suspend.
	 *
	 * http://thread.gmane.org/gmane.linux.ide/46764
	 */
	ata_port_request_pm(ap, mesg, 0,
			    ATA_EHI_QUIET | ATA_EHI_NO_AUTOPSY |
			    ATA_EHI_NO_RECOVERY,
			    async);
}

static int ata_port_pm_suspend(struct device *dev)
{
	struct ata_port *ap = to_ata_port(dev);

	if (pm_runtime_suspended(dev))
		return 0;

	ata_port_suspend(ap, PMSG_SUSPEND, false);
	return 0;
}

static int ata_port_pm_freeze(struct device *dev)
{
	struct ata_port *ap = to_ata_port(dev);

	if (pm_runtime_suspended(dev))
		return 0;

	ata_port_suspend(ap, PMSG_FREEZE, false);
	return 0;
}

static int ata_port_pm_poweroff(struct device *dev)
{
	if (!pm_runtime_suspended(dev))
		ata_port_suspend(to_ata_port(dev), PMSG_HIBERNATE, false);
	return 0;
}

static void ata_port_resume(struct ata_port *ap, pm_message_t mesg,
			    bool async)
{
	ata_port_request_pm(ap, mesg, ATA_EH_RESET,
			    ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET,
			    async);
}

static int ata_port_pm_resume(struct device *dev)
{
	if (!pm_runtime_suspended(dev))
		ata_port_resume(to_ata_port(dev), PMSG_RESUME, true);
	return 0;
}

/*
 * For ODDs, the upper layer will poll for media change every few seconds,
 * which will make it enter and leave suspend state every few seconds. And
 * as each suspend will cause a hard/soft reset, the gain of runtime suspend
 * is very little and the ODD may malfunction after constantly being reset.
 * So the idle callback here will not proceed to suspend if a non-ZPODD capable
 * ODD is attached to the port.
 */
static int ata_port_runtime_idle(struct device *dev)
{
	struct ata_port *ap = to_ata_port(dev);
	struct ata_link *link;
	struct ata_device *adev;

	ata_for_each_link(link, ap, HOST_FIRST) {
		ata_for_each_dev(adev, link, ENABLED)
			if (adev->class == ATA_DEV_ATAPI &&
			    !zpodd_dev_enabled(adev))
				return -EBUSY;
	}

	return 0;
}

static int ata_port_runtime_suspend(struct device *dev)
{
	ata_port_suspend(to_ata_port(dev), PMSG_AUTO_SUSPEND, false);
	return 0;
}

static int ata_port_runtime_resume(struct device *dev)
{
	ata_port_resume(to_ata_port(dev), PMSG_AUTO_RESUME, false);
	return 0;
}

static const struct dev_pm_ops ata_port_pm_ops = {
	.suspend = ata_port_pm_suspend,
	.resume = ata_port_pm_resume,
	.freeze = ata_port_pm_freeze,
	.thaw = ata_port_pm_resume,
	.poweroff = ata_port_pm_poweroff,
	.restore = ata_port_pm_resume,

	.runtime_suspend = ata_port_runtime_suspend,
	.runtime_resume = ata_port_runtime_resume,
	.runtime_idle = ata_port_runtime_idle,
};

/* sas ports don't participate in pm runtime management of ata_ports,
 * and need to resume ata devices at the domain level, not the per-port
 * level. sas suspend/resume is async to allow parallel port recovery
 * since sas has multiple ata_port instances per Scsi_Host.
 */
void ata_sas_port_suspend(struct ata_port *ap)
{
	ata_port_suspend(ap, PMSG_SUSPEND, true);
}
EXPORT_SYMBOL_GPL(ata_sas_port_suspend);

void ata_sas_port_resume(struct ata_port *ap)
{
	ata_port_resume(ap, PMSG_RESUME, true);
}
EXPORT_SYMBOL_GPL(ata_sas_port_resume);

/**
 *	ata_host_suspend - suspend host
 *	@host: host to suspend
 *	@mesg: PM message
 *
 *	Suspend @host.  Actual operation is performed by port suspend.
 */
void ata_host_suspend(struct ata_host *host, pm_message_t mesg)
{
	host->dev->power.power_state = mesg;
}
EXPORT_SYMBOL_GPL(ata_host_suspend);

/**
 *	ata_host_resume - resume host
 *	@host: host to resume
 *
 *	Resume @host.  Actual operation is performed by port resume.
 */
void ata_host_resume(struct ata_host *host)
{
	host->dev->power.power_state = PMSG_ON;
}
EXPORT_SYMBOL_GPL(ata_host_resume);
#endif

const struct device_type ata_port_type = {
	.name = ATA_PORT_TYPE_NAME,
#ifdef CONFIG_PM
	.pm = &ata_port_pm_ops,
#endif
};

/**
 *	ata_dev_init - Initialize an ata_device structure
 *	@dev: Device structure to initialize
 *
 *	Initialize @dev in preparation for probing.
 *
 *	LOCKING:
 *	Inherited from caller.
 */
void ata_dev_init(struct ata_device *dev)
{
	struct ata_link *link = ata_dev_phys_link(dev);
	struct ata_port *ap = link->ap;
	unsigned long flags;

	/* SATA spd limit is bound to the attached device, reset together */
	link->sata_spd_limit = link->hw_sata_spd_limit;
	link->sata_spd = 0;

	/* High bits of dev->flags are used to record warm plug
	 * requests which occur asynchronously.  Synchronize using
	 * host lock.
	 */
	spin_lock_irqsave(ap->lock, flags);
	dev->flags &= ~ATA_DFLAG_INIT_MASK;
	dev->quirks = 0;
	spin_unlock_irqrestore(ap->lock, flags);

	memset((void *)dev + ATA_DEVICE_CLEAR_BEGIN, 0,
	       ATA_DEVICE_CLEAR_END - ATA_DEVICE_CLEAR_BEGIN);
	dev->pio_mask = UINT_MAX;
	dev->mwdma_mask = UINT_MAX;
	dev->udma_mask = UINT_MAX;
}

/**
 *	ata_link_init - Initialize an ata_link structure
 *	@ap: ATA port link is attached to
 *	@link: Link structure to initialize
 *	@pmp: Port multiplier port number
 *
 *	Initialize @link.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 */
void ata_link_init(struct ata_port *ap, struct ata_link *link, int pmp)
{
	int i;

	/* clear everything except for devices */
	memset((void *)link + ATA_LINK_CLEAR_BEGIN, 0,
	       ATA_LINK_CLEAR_END - ATA_LINK_CLEAR_BEGIN);

	link->ap = ap;
	link->pmp = pmp;
	link->active_tag = ATA_TAG_POISON;
	link->hw_sata_spd_limit = UINT_MAX;
	INIT_WORK(&link->deferred_qc_work, ata_scsi_deferred_qc_work);

	/* can't use iterator, ap isn't initialized yet */
	for (i = 0; i < ATA_MAX_DEVICES; i++) {
		struct ata_device *dev = &link->device[i];

		dev->link = link;
		dev->devno = dev - link->device;
#ifdef CONFIG_ATA_ACPI
		dev->gtf_filter = ata_acpi_gtf_filter;
#endif
		ata_dev_init(dev);
	}
}

/**
 *	sata_link_init_spd - Initialize link->sata_spd_limit
 *	@link: Link to configure sata_spd_limit for
 *
 *	Initialize ``link->[hw_]sata_spd_limit`` to the currently
 *	configured value.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 *
 *	RETURNS:
 *	0 on success, -errno on failure.
 */
int sata_link_init_spd(struct ata_link *link)
{
	u8 spd;
	int rc;

	rc = sata_scr_read(link, SCR_CONTROL, &link->saved_scontrol);
	if (rc)
		return rc;

	spd = (link->saved_scontrol >> 4) & 0xf;
	if (spd)
		link->hw_sata_spd_limit &= (1 << spd) - 1;

	ata_force_link_limits(link);

	link->sata_spd_limit = link->hw_sata_spd_limit;

	return 0;
}

/**
 *	ata_port_alloc - allocate and initialize basic ATA port resources
 *	@host: ATA host this allocated port belongs to
 *
 *	Allocate and initialize basic ATA port resources.
 *
 *	RETURNS:
 *	Allocate ATA port on success, NULL on failure.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 */
struct ata_port *ata_port_alloc(struct ata_host *host)
{
	struct ata_port *ap;
	int id;

	ap = kzalloc_obj(*ap);
	if (!ap)
		return NULL;

	ap->pflags |= ATA_PFLAG_INITIALIZING | ATA_PFLAG_FROZEN;
	ap->lock = &host->lock;
	id = ida_alloc_min(&ata_ida, 1, GFP_KERNEL);
	if (id < 0) {
		kfree(ap);
		return NULL;
	}
	ap->print_id = id;
	ap->host = host;
	ap->dev = host->dev;

	mutex_init(&ap->scsi_scan_mutex);
	INIT_DELAYED_WORK(&ap->hotplug_task, ata_scsi_hotplug);
	INIT_DELAYED_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan);
	INIT_LIST_HEAD(&ap->eh_done_q);
	init_waitqueue_head(&ap->eh_wait_q);
	init_completion(&ap->park_req_pending);
	timer_setup(&ap->fastdrain_timer, ata_eh_fastdrain_timerfn,
		    TIMER_DEFERRABLE);

	ap->cbl = ATA_CBL_NONE;

	ata_link_init(ap, &ap->link, 0);

#ifdef ATA_IRQ_TRAP
	ap->stats.unhandled_irq = 1;
	ap->stats.idle_irq = 1;
#endif
	ata_sff_port_init(ap);

	ata_force_pflags(ap);

	return ap;
}
EXPORT_SYMBOL_GPL(ata_port_alloc);

void ata_port_free(struct ata_port *ap)
{
	if (!ap)
		return;

	kfree(ap->pmp_link);
	kfree(ap->slave_link);
	ida_free(&ata_ida, ap->print_id);
	kfree(ap);
}
EXPORT_SYMBOL_GPL(ata_port_free);

static void ata_devres_release(struct device *gendev, void *res)
{
	struct ata_host *host = dev_get_drvdata(gendev);
	int i;

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		if (!ap)
			continue;

		if (ap->scsi_host)
			scsi_host_put(ap->scsi_host);

	}

	dev_set_drvdata(gendev, NULL);
	ata_host_put(host);
}

static void ata_host_release(struct kref *kref)
{
	struct ata_host *host = container_of(kref, struct ata_host, kref);
	int i;

	for (i = 0; i < host->n_ports; i++) {
		ata_port_free(host->ports[i]);
		host->ports[i] = NULL;
	}
	kfree(host);
}

void ata_host_get(struct ata_host *host)
{
	kref_get(&host->kref);
}

void ata_host_put(struct ata_host *host)
{
	kref_put(&host->kref, ata_host_release);
}
EXPORT_SYMBOL_GPL(ata_host_put);

/**
 *	ata_host_alloc - allocate and init basic ATA host resources
 *	@dev: generic device this host is associated with
 *	@n_ports: the number of ATA ports associated with this host
 *
 *	Allocate and initialize basic ATA host resources.  LLD calls
 *	this function to allocate a host, initializes it fully and
 *	attaches it using ata_host_register().
 *
 *	RETURNS:
 *	Allocate ATA host on success, NULL on failure.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 */
struct ata_host *ata_host_alloc(struct device *dev, int n_ports)
{
	struct ata_host *host;
	size_t sz;
	int i;
	void *dr;

	/* alloc a container for our list of ATA ports (buses) */
	sz = sizeof(struct ata_host) + n_ports * sizeof(void *);
	host = kzalloc(sz, GFP_KERNEL);
	if (!host)
		return NULL;

	if (!devres_open_group(dev, NULL, GFP_KERNEL)) {
		kfree(host);
		return NULL;
	}

	dr = devres_alloc(ata_devres_release, 0, GFP_KERNEL);
	if (!dr) {
		kfree(host);
		goto err_out;
	}

	devres_add(dev, dr);
	dev_set_drvdata(dev, host);

	spin_lock_init(&host->lock);
	mutex_init(&host->eh_mutex);
	host->dev = dev;
	host->n_ports = n_ports;
	kref_init(&host->kref);

	/* allocate ports bound to this host */
	for (i = 0; i < n_ports; i++) {
		struct ata_port *ap;

		ap = ata_port_alloc(host);
		if (!ap)
			goto err_out;

		ap->port_no = i;
		host->ports[i] = ap;
	}

	devres_remove_group(dev, NULL);
	return host;

 err_out:
	devres_release_group(dev, NULL);
	return NULL;
}
EXPORT_SYMBOL_GPL(ata_host_alloc);

/**
 *	ata_host_alloc_pinfo - alloc host and init with port_info array
 *	@dev: generic device this host is associated with
 *	@ppi: array of ATA port_info to initialize host with
 *	@n_ports: number of ATA ports attached to this host
 *
 *	Allocate ATA host and initialize with info from @ppi.  If NULL
 *	terminated, @ppi may contain fewer entries than @n_ports.  The
 *	last entry will be used for the remaining ports.
 *
 *	RETURNS:
 *	Allocate ATA host on success, NULL on failure.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 */
struct ata_host *ata_host_alloc_pinfo(struct device *dev,
				      const struct ata_port_info * const * ppi,
				      int n_ports)
{
	const struct ata_port_info *pi = &ata_dummy_port_info;
	struct ata_host *host;
	int i, j;

	host = ata_host_alloc(dev, n_ports);
	if (!host)
		return NULL;

	for (i = 0, j = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		if (ppi[j])
			pi = ppi[j++];

		ap->pio_mask = pi->pio_mask;
		ap->mwdma_mask = pi->mwdma_mask;
		ap->udma_mask = pi->udma_mask;
		ap->flags |= pi->flags;
		ap->link.flags |= pi->link_flags;
		ap->ops = pi->port_ops;

		if (!host->ops && (pi->port_ops != &ata_dummy_port_ops))
			host->ops = pi->port_ops;
	}

	return host;
}
EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);

static void ata_host_stop(struct device *gendev, void *res)
{
	struct ata_host *host = dev_get_drvdata(gendev);
	int i;

	WARN_ON(!(host->flags & ATA_HOST_STARTED));

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		if (ap->ops->port_stop)
			ap->ops->port_stop(ap);
	}

	if (host->ops->host_stop)
		host->ops->host_stop(host);
}

/**
 *	ata_finalize_port_ops - finalize ata_port_operations
 *	@ops: ata_port_operations to finalize
 *
 *	An ata_port_operations can inherit from another ops and that
 *	ops can again inherit from another.  This can go on as many
 *	times as necessary as long as there is no loop in the
 *	inheritance chain.
 *
 *	Ops tables are finalized when the host is started.  NULL or
 *	unspecified entries are inherited from the closet ancestor
 *	which has the method and the entry is populated with it.
 *	After finalization, the ops table directly points to all the
 *	methods and ->inherits is no longer necessary and cleared.
 *
 *	Using ATA_OP_NULL, inheriting ops can force a method to NULL.
 *
 *	LOCKING:
 *	None.
 */
static void ata_finalize_port_ops(struct ata_port_operations *ops)
{
	static DEFINE_SPINLOCK(lock);
	const struct ata_port_operations *cur;
	void **begin = (void **)ops;
	void **end = (void **)&ops->inherits;
	void **pp;

	if (!ops || !ops->inherits)
		return;

	spin_lock(&lock);

	for (cur = ops->inherits; cur; cur = cur->inherits) {
		void **inherit = (void **)cur;

		for (pp = begin; pp < end; pp++, inherit++)
			if (!*pp)
				*pp = *inherit;
	}

	for (pp = begin; pp < end; pp++)
		if (IS_ERR(*pp))
			*pp = NULL;

	ops->inherits = NULL;

	spin_unlock(&lock);
}

/**
 *	ata_host_start - start and freeze ports of an ATA host
 *	@host: ATA host to start ports for
 *
 *	Start and then freeze ports of @host.  Started status is
 *	recorded in host->flags, so this function can be called
 *	multiple times.  Ports are guaranteed to get started only
 *	once.  If host->ops is not initialized yet, it is set to the
 *	first non-dummy port ops.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 *
 *	RETURNS:
 *	0 if all ports are started successfully, -errno otherwise.
 */
int ata_host_start(struct ata_host *host)
{
	int have_stop = 0;
	void *start_dr = NULL;
	int i, rc;

	if (host->flags & ATA_HOST_STARTED)
		return 0;

	ata_finalize_port_ops(host->ops);

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		ata_finalize_port_ops(ap->ops);

		if (!host->ops && !ata_port_is_dummy(ap))
			host->ops = ap->ops;

		if (ap->ops->port_stop)
			have_stop = 1;
	}

	if (host->ops && host->ops->host_stop)
		have_stop = 1;

	if (have_stop) {
		start_dr = devres_alloc(ata_host_stop, 0, GFP_KERNEL);
		if (!start_dr)
			return -ENOMEM;
	}

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		if (ap->ops->port_start) {
			rc = ap->ops->port_start(ap);
			if (rc) {
				if (rc != -ENODEV)
					dev_err(host->dev,
						"failed to start port %d (errno=%d)\n",
						i, rc);
				goto err_out;
			}
		}
		ata_eh_freeze_port(ap);
	}

	if (start_dr)
		devres_add(host->dev, start_dr);
	host->flags |= ATA_HOST_STARTED;
	return 0;

 err_out:
	while (--i >= 0) {
		struct ata_port *ap = host->ports[i];

		if (ap->ops->port_stop)
			ap->ops->port_stop(ap);
	}
	devres_free(start_dr);
	return rc;
}
EXPORT_SYMBOL_GPL(ata_host_start);

/**
 *	ata_host_init - Initialize a host struct for sas (ipr, libsas)
 *	@host:	host to initialize
 *	@dev:	device host is attached to
 *	@ops:	port_ops
 *
 */
void ata_host_init(struct ata_host *host, struct device *dev,
		   struct ata_port_operations *ops)
{
	spin_lock_init(&host->lock);
	mutex_init(&host->eh_mutex);
	host->n_tags = ATA_MAX_QUEUE;
	host->dev = dev;
	host->ops = ops;
	kref_init(&host->kref);
}
EXPORT_SYMBOL_GPL(ata_host_init);

void ata_port_probe(struct ata_port *ap)
{
	struct ata_eh_info *ehi = &ap->link.eh_info;
	unsigned long flags;

	ata_acpi_port_power_on(ap);

	/* kick EH for boot probing */
	spin_lock_irqsave(ap->lock, flags);

	ehi->probe_mask |= ATA_ALL_DEVICES;
	ehi->action |= ATA_EH_RESET;
	ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET;

	ap->pflags &= ~ATA_PFLAG_INITIALIZING;
	ap->pflags |= ATA_PFLAG_LOADING;
	ata_port_schedule_eh(ap);

	spin_unlock_irqrestore(ap->lock, flags);
}
EXPORT_SYMBOL_GPL(ata_port_probe);

static void async_port_probe(void *data, async_cookie_t cookie)
{
	struct ata_port *ap = data;

	/*
	 * If we're not allowed to scan this host in parallel,
	 * we need to wait until all previous scans have completed
	 * before going further.
	 * Jeff Garzik says this is only within a controller, so we
	 * don't need to wait for port 0, only for later ports.
	 */
	if (!(ap->host->flags & ATA_HOST_PARALLEL_SCAN) && ap->port_no != 0)
		async_synchronize_cookie(cookie);

	ata_port_probe(ap);
	ata_port_wait_eh(ap);

	/* in order to keep device order, we need to synchronize at this point */
	async_synchronize_cookie(cookie);

	ata_scsi_scan_host(ap, 1);
}

/**
 *	ata_host_register - register initialized ATA host
 *	@host: ATA host to register
 *	@sht: template for SCSI host
 *
 *	Register initialized ATA host.  @host is allocated using
 *	ata_host_alloc() and fully initialized by LLD.  This function
 *	starts ports, registers @host with ATA and SCSI layers and
 *	probe registered devices.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 *
 *	RETURNS:
 *	0 on success, -errno otherwise.
 */
int ata_host_register(struct ata_host *host, const struct scsi_host_template *sht)
{
	int i, rc;

	host->n_tags = clamp(sht->can_queue, 1, ATA_MAX_QUEUE);

	/* host must have been started */
	if (!(host->flags & ATA_HOST_STARTED)) {
		dev_err(host->dev, "BUG: trying to register unstarted host\n");
		WARN_ON(1);
		return -EINVAL;
	}

	/* Create associated sysfs transport objects  */
	for (i = 0; i < host->n_ports; i++) {
		rc = ata_tport_add(host->dev,host->ports[i]);
		if (rc) {
			goto err_tadd;
		}
	}

	rc = ata_scsi_add_hosts(host, sht);
	if (rc)
		goto err_tadd;

	/* set cable, sata_spd_limit and report */
	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];
		unsigned int xfer_mask;

		/* set SATA cable type if still unset */
		if (ap->cbl == ATA_CBL_NONE && (ap->flags & ATA_FLAG_SATA))
			ap->cbl = ATA_CBL_SATA;

		/* init sata_spd_limit to the current value */
		sata_link_init_spd(&ap->link);
		if (ap->slave_link)
			sata_link_init_spd(ap->slave_link);

		/* print per-port info to dmesg */
		xfer_mask = ata_pack_xfermask(ap->pio_mask, ap->mwdma_mask,
					      ap->udma_mask);

		if (!ata_port_is_dummy(ap)) {
			ata_port_info(ap, "%cATA max %s %s\n",
				      (ap->flags & ATA_FLAG_SATA) ? 'S' : 'P',
				      ata_mode_string(xfer_mask),
				      ap->link.eh_info.desc);
			ata_ehi_clear_desc(&ap->link.eh_info);
		} else
			ata_port_info(ap, "DUMMY\n");
	}

	/* perform each probe asynchronously */
	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];
		ap->cookie = async_schedule(async_port_probe, ap);
	}

	return 0;

 err_tadd:
	while (--i >= 0) {
		ata_tport_delete(host->ports[i]);
	}
	return rc;

}
EXPORT_SYMBOL_GPL(ata_host_register);

/**
 *	ata_host_activate - start host, request IRQ and register it
 *	@host: target ATA host
 *	@irq: IRQ to request
 *	@irq_handler: irq_handler used when requesting IRQ
 *	@irq_flags: irq_flags used when requesting IRQ
 *	@sht: scsi_host_template to use when registering the host
 *
 *	After allocating an ATA host and initializing it, most libata
 *	LLDs perform three steps to activate the host - start host,
 *	request IRQ and register it.  This helper takes necessary
 *	arguments and performs the three steps in one go.
 *
 *	An invalid IRQ skips the IRQ registration and expects the host to
 *	have set polling mode on the port. In this case, @irq_handler
 *	should be NULL.
 *
 *	LOCKING:
 *	Inherited from calling layer (may sleep).
 *
 *	RETURNS:
 *	0 on success, -errno otherwise.
 */
int ata_host_activate(struct ata_host *host, int irq,
		      irq_handler_t irq_handler, unsigned long irq_flags,
		      const struct scsi_host_template *sht)
{
	int i, rc;
	char *irq_desc;

	rc = ata_host_start(host);
	if (rc)
		return rc;

	/* Special case for polling mode */
	if (!irq) {
		WARN_ON(irq_handler);
		return ata_host_register(host, sht);
	}

	irq_desc = devm_kasprintf(host->dev, GFP_KERNEL, "%s[%s]",
				  dev_driver_string(host->dev),
				  dev_name(host->dev));
	if (!irq_desc)
		return -ENOMEM;

	rc = devm_request_irq(host->dev, irq, irq_handler, irq_flags,
			      irq_desc, host);
	if (rc)
		return rc;

	for (i = 0; i < host->n_ports; i++)
		ata_port_desc_misc(host->ports[i], irq);

	rc = ata_host_register(host, sht);
	/* if failed, just free the IRQ and leave ports alone */
	if (rc)
		devm_free_irq(host->dev, irq, host);

	return rc;
}
EXPORT_SYMBOL_GPL(ata_host_activate);

/**
 *	ata_dev_free_resources - Free a device resources
 *	@dev: Target ATA device
 *
 *	Free resources allocated to support a device features.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 */
void ata_dev_free_resources(struct ata_device *dev)
{
	if (zpodd_dev_enabled(dev))
		zpodd_exit(dev);

	ata_dev_cleanup_cdl_resources(dev);
}

/**
 *	ata_port_detach - Detach ATA port in preparation of device removal
 *	@ap: ATA port to be detached
 *
 *	Detach all ATA devices and the associated SCSI devices of @ap;
 *	then, remove the associated SCSI host.  @ap is guaranteed to
 *	be quiescent on return from this function.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 */
static void ata_port_detach(struct ata_port *ap)
{
	unsigned long flags;
	struct ata_link *link;
	struct ata_device *dev;

	/* Ensure ata_port probe has completed */
	async_synchronize_cookie(ap->cookie + 1);

	/* Wait for any ongoing EH */
	ata_port_wait_eh(ap);

	mutex_lock(&ap->scsi_scan_mutex);
	spin_lock_irqsave(ap->lock, flags);

	/* Remove scsi devices */
	ata_for_each_link(link, ap, HOST_FIRST) {
		ata_for_each_dev(dev, link, ALL) {
			if (dev->sdev) {
				spin_unlock_irqrestore(ap->lock, flags);
				scsi_remove_device(dev->sdev);
				spin_lock_irqsave(ap->lock, flags);
				dev->sdev = NULL;
			}
		}
	}

	/* Tell EH to disable all devices */
	ap->pflags |= ATA_PFLAG_UNLOADING;
	ata_port_schedule_eh(ap);

	spin_unlock_irqrestore(ap->lock, flags);
	mutex_unlock(&ap->scsi_scan_mutex);

	/* wait till EH commits suicide */
	ata_port_wait_eh(ap);

	/* It better be dead now and not have any remaining deferred qc. */
	WARN_ON(!(ap->pflags & ATA_PFLAG_UNLOADED));

	cancel_delayed_work_sync(&ap->hotplug_task);
	cancel_delayed_work_sync(&ap->scsi_rescan_task);

	ata_for_each_link(link, ap, PMP_FIRST) {
		WARN_ON(link->deferred_qc);
		cancel_work_sync(&link->deferred_qc_work);
	}

	/* Delete port multiplier link transport devices */
	if (ap->pmp_link) {
		int i;

		for (i = 0; i < SATA_PMP_MAX_PORTS; i++)
			ata_tlink_delete(&ap->pmp_link[i]);
	}

	/* Remove the associated SCSI host */
	scsi_remove_host(ap->scsi_host);
	ata_tport_delete(ap);
}

/**
 *	ata_host_detach - Detach all ports of an ATA host
 *	@host: Host to detach
 *
 *	Detach all ports of @host.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep).
 */
void ata_host_detach(struct ata_host *host)
{
	int i;

	for (i = 0; i < host->n_ports; i++)
		ata_port_detach(host->ports[i]);

	/* the host is dead now, dissociate ACPI */
	ata_acpi_dissociate(host);
}
EXPORT_SYMBOL_GPL(ata_host_detach);

#ifdef CONFIG_PCI

/**
 *	ata_pci_remove_one - PCI layer callback for device removal
 *	@pdev: PCI device that was removed
 *
 *	PCI layer indicates to libata via this hook that hot-unplug or
 *	module unload event has occurred.  Detach all ports.  Resource
 *	release is handled via devres.
 *
 *	LOCKING:
 *	Inherited from PCI layer (may sleep).
 */
void ata_pci_remove_one(struct pci_dev *pdev)
{
	struct ata_host *host = pci_get_drvdata(pdev);

	ata_host_detach(host);
}
EXPORT_SYMBOL_GPL(ata_pci_remove_one);

void ata_pci_shutdown_one(struct pci_dev *pdev)
{
	struct ata_host *host = pci_get_drvdata(pdev);
	int i;

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];

		ap->pflags |= ATA_PFLAG_FROZEN;

		/* Disable port interrupts */
		if (ap->ops->freeze)
			ap->ops->freeze(ap);

		/* Stop the port DMA engines */
		if (ap->ops->port_stop)
			ap->ops->port_stop(ap);
	}
}
EXPORT_SYMBOL_GPL(ata_pci_shutdown_one);

/* move to PCI subsystem */
int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits)
{
	unsigned long tmp = 0;

	switch (bits->width) {
	case 1: {
		u8 tmp8 = 0;
		pci_read_config_byte(pdev, bits->reg, &tmp8);
		tmp = tmp8;
		break;
	}
	case 2: {
		u16 tmp16 = 0;
		pci_read_config_word(pdev, bits->reg, &tmp16);
		tmp = tmp16;
		break;
	}
	case 4: {
		u32 tmp32 = 0;
		pci_read_config_dword(pdev, bits->reg, &tmp32);
		tmp = tmp32;
		break;
	}

	default:
		return -EINVAL;
	}

	tmp &= bits->mask;

	return (tmp == bits->val) ? 1 : 0;
}
EXPORT_SYMBOL_GPL(pci_test_config_bits);

#ifdef CONFIG_PM
void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
	pci_save_state(pdev);
	pci_disable_device(pdev);

	if (mesg.event & PM_EVENT_SLEEP)
		pci_set_power_state(pdev, PCI_D3hot);
}
EXPORT_SYMBOL_GPL(ata_pci_device_do_suspend);

int ata_pci_device_do_resume(struct pci_dev *pdev)
{
	int rc;

	pci_set_power_state(pdev, PCI_D0);
	pci_restore_state(pdev);

	rc = pcim_enable_device(pdev);
	if (rc) {
		dev_err(&pdev->dev,
			"failed to enable device after resume (%d)\n", rc);
		return rc;
	}

	pci_set_master(pdev);
	return 0;
}
EXPORT_SYMBOL_GPL(ata_pci_device_do_resume);

int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
	struct ata_host *host = pci_get_drvdata(pdev);

	ata_host_suspend(host, mesg);

	ata_pci_device_do_suspend(pdev, mesg);

	return 0;
}
EXPORT_SYMBOL_GPL(ata_pci_device_suspend);

int ata_pci_device_resume(struct pci_dev *pdev)
{
	struct ata_host *host = pci_get_drvdata(pdev);
	int rc;

	rc = ata_pci_device_do_resume(pdev);
	if (rc == 0)
		ata_host_resume(host);
	return rc;
}
EXPORT_SYMBOL_GPL(ata_pci_device_resume);
#endif /* CONFIG_PM */
#endif /* CONFIG_PCI */

/**
 *	ata_platform_remove_one - Platform layer callback for device removal
 *	@pdev: Platform device that was removed
 *
 *	Platform layer indicates to libata via this hook that hot-unplug or
 *	module unload event has occurred.  Detach all ports.  Resource
 *	release is handled via devres.
 *
 *	LOCKING:
 *	Inherited from platform layer (may sleep).
 */
void ata_platform_remove_one(struct platform_device *pdev)
{
	struct ata_host *host = platform_get_drvdata(pdev);

	ata_host_detach(host);
}
EXPORT_SYMBOL_GPL(ata_platform_remove_one);

#ifdef CONFIG_ATA_FORCE

#define force_cbl(name, flag)				\
	{ #name,	.cbl		= (flag) }

#define force_spd_limit(spd, val)			\
	{ #spd,	.spd_limit		= (val) }

#define force_xfer(mode, shift)				\
	{ #mode,	.xfer_mask	= (1UL << (shift)) }

#define force_lflag_on(name, flags)			\
	{ #name,	.lflags_on	= (flags) }

#define force_lflag_onoff(name, flags)			\
	{ "no" #name,	.lflags_on	= (flags) },	\
	{ #name,	.lflags_off	= (flags) }

#define force_pflag_on(name, flags)			\
	{ #name,	.pflags_on	= (flags) }

#define force_quirk_on(name, flag)			\
	{ #name,	.quirk_on	= (flag) }

#define force_quirk_val(name, flag, val)		\
	{ #name,	.quirk_on	= (flag),	\
			.value		= (val) }

#define force_quirk_onoff(name, flag)			\
	{ "no" #name,	.quirk_on	= (flag) },	\
	{ #name,	.quirk_off	= (flag) }

/*
 * If the ata_force_param struct member 'name' ends with '=', then the value
 * after the equal sign will be parsed as an u64, and will be saved in the
 * ata_force_param struct member 'value'. This works because each libata.force
 * entry (struct ata_force_ent) is separated by commas, so each entry represents
 * a single quirk, and can thus only have a single value.
 */
static const struct ata_force_param force_tbl[] __initconst = {
	force_cbl(40c,			ATA_CBL_PATA40),
	force_cbl(80c,			ATA_CBL_PATA80),
	force_cbl(short40c,		ATA_CBL_PATA40_SHORT),
	force_cbl(unk,			ATA_CBL_PATA_UNK),
	force_cbl(ign,			ATA_CBL_PATA_IGN),
	force_cbl(sata,			ATA_CBL_SATA),

	force_spd_limit(1.5Gbps,	1),
	force_spd_limit(3.0Gbps,	2),

	force_xfer(pio0,		ATA_SHIFT_PIO + 0),
	force_xfer(pio1,		ATA_SHIFT_PIO + 1),
	force_xfer(pio2,		ATA_SHIFT_PIO + 2),
	force_xfer(pio3,		ATA_SHIFT_PIO + 3),
	force_xfer(pio4,		ATA_SHIFT_PIO + 4),
	force_xfer(pio5,		ATA_SHIFT_PIO + 5),
	force_xfer(pio6,		ATA_SHIFT_PIO + 6),
	force_xfer(mwdma0,		ATA_SHIFT_MWDMA + 0),
	force_xfer(mwdma1,		ATA_SHIFT_MWDMA + 1),
	force_xfer(mwdma2,		ATA_SHIFT_MWDMA + 2),
	force_xfer(mwdma3,		ATA_SHIFT_MWDMA + 3),
	force_xfer(mwdma4,		ATA_SHIFT_MWDMA + 4),
	force_xfer(udma0,		ATA_SHIFT_UDMA + 0),
	force_xfer(udma16,		ATA_SHIFT_UDMA + 0),
	force_xfer(udma/16,		ATA_SHIFT_UDMA + 0),
	force_xfer(udma1,		ATA_SHIFT_UDMA + 1),
	force_xfer(udma25,		ATA_SHIFT_UDMA + 1),
	force_xfer(udma/25,		ATA_SHIFT_UDMA + 1),
	force_xfer(udma2,		ATA_SHIFT_UDMA + 2),
	force_xfer(udma33,		ATA_SHIFT_UDMA + 2),
	force_xfer(udma/33,		ATA_SHIFT_UDMA + 2),
	force_xfer(udma3,		ATA_SHIFT_UDMA + 3),
	force_xfer(udma44,		ATA_SHIFT_UDMA + 3),
	force_xfer(udma/44,		ATA_SHIFT_UDMA + 3),
	force_xfer(udma4,		ATA_SHIFT_UDMA + 4),
	force_xfer(udma66,		ATA_SHIFT_UDMA + 4),
	force_xfer(udma/66,		ATA_SHIFT_UDMA + 4),
	force_xfer(udma5,		ATA_SHIFT_UDMA + 5),
	force_xfer(udma100,		ATA_SHIFT_UDMA + 5),
	force_xfer(udma/100,		ATA_SHIFT_UDMA + 5),
	force_xfer(udma6,		ATA_SHIFT_UDMA + 6),
	force_xfer(udma133,		ATA_SHIFT_UDMA + 6),
	force_xfer(udma/133,		ATA_SHIFT_UDMA + 6),
	force_xfer(udma7,		ATA_SHIFT_UDMA + 7),

	force_lflag_on(nohrst,		ATA_LFLAG_NO_HRST),
	force_lflag_on(nosrst,		ATA_LFLAG_NO_SRST),
	force_lflag_on(norst,		ATA_LFLAG_NO_HRST | ATA_LFLAG_NO_SRST),
	force_lflag_on(rstonce,		ATA_LFLAG_RST_ONCE),
	force_lflag_onoff(dbdelay,	ATA_LFLAG_NO_DEBOUNCE_DELAY),

	force_pflag_on(external,	ATA_PFLAG_EXTERNAL),

	force_quirk_onoff(ncq,		ATA_QUIRK_NONCQ),
	force_quirk_onoff(ncqtrim,	ATA_QUIRK_NO_NCQ_TRIM),
	force_quirk_onoff(ncqati,	ATA_QUIRK_NO_NCQ_ON_ATI),

	force_quirk_onoff(trim,		ATA_QUIRK_NOTRIM),
	force_quirk_on(trim_zero,	ATA_QUIRK_ZERO_AFTER_TRIM),
	force_quirk_on(max_trim_128m,	ATA_QUIRK_MAX_TRIM_128M),

	force_quirk_onoff(dma,		ATA_QUIRK_NODMA),
	force_quirk_on(atapi_dmadir,	ATA_QUIRK_ATAPI_DMADIR),
	force_quirk_on(atapi_mod16_dma,	ATA_QUIRK_ATAPI_MOD16_DMA),

	force_quirk_onoff(dmalog,	ATA_QUIRK_NO_DMA_LOG),
	force_quirk_onoff(iddevlog,	ATA_QUIRK_NO_ID_DEV_LOG),
	force_quirk_onoff(logdir,	ATA_QUIRK_NO_LOG_DIR),

	force_quirk_val(max_sec_128,	ATA_QUIRK_MAX_SEC,	128),
	force_quirk_val(max_sec_1024,	ATA_QUIRK_MAX_SEC,	1024),
	force_quirk_on(max_sec=,	ATA_QUIRK_MAX_SEC),
	force_quirk_on(max_sec_lba48,	ATA_QUIRK_MAX_SEC_LBA48),

	force_quirk_onoff(lpm,		ATA_QUIRK_NOLPM),
	force_quirk_onoff(setxfer,	ATA_QUIRK_NOSETXFER),
	force_quirk_on(dump_id,		ATA_QUIRK_DUMP_ID),
	force_quirk_onoff(fua,		ATA_QUIRK_NO_FUA),

	force_quirk_on(disable,		ATA_QUIRK_DISABLE),
};

static int __init ata_parse_force_one(char **cur,
				      struct ata_force_ent *force_ent,
				      const char **reason)
{
	char *start = *cur, *p = *cur;
	char *id, *val, *endp, *equalsign, *char_after_equalsign;
	const struct ata_force_param *match_fp = NULL;
	u64 val_after_equalsign;
	int nr_matches = 0, i;

	/* find where this param ends and update *cur */
	while (*p != '\0' && *p != ',')
		p++;

	if (*p == '\0')
		*cur = p;
	else
		*cur = p + 1;

	*p = '\0';

	/* parse */
	p = strchr(start, ':');
	if (!p) {
		val = strstrip(start);
		goto parse_val;
	}
	*p = '\0';

	id = strstrip(start);
	val = strstrip(p + 1);

	/* parse id */
	p = strchr(id, '.');
	if (p) {
		*p++ = '\0';
		force_ent->device = simple_strtoul(p, &endp, 10);
		if (p == endp || *endp != '\0') {
			*reason = "invalid device";
			return -EINVAL;
		}
	}

	force_ent->port = simple_strtoul(id, &endp, 10);
	if (id == endp || *endp != '\0') {
		*reason = "invalid port/link";
		return -EINVAL;
	}

 parse_val:
	equalsign = strchr(val, '=');
	if (equalsign) {
		char_after_equalsign = equalsign + 1;
		if (!strlen(char_after_equalsign) ||
		    kstrtoull(char_after_equalsign, 10, &val_after_equalsign)) {
			*reason = "invalid value after equal sign";
			return -EINVAL;
		}
	}

	/* Parse the parameter value. */
	for (i = 0; i < ARRAY_SIZE(force_tbl); i++) {
		const struct ata_force_param *fp = &force_tbl[i];

		/*
		 * If val contains equal sign, match has to be exact, i.e.
		 * shortcuts are not supported.
		 */
		if (equalsign &&
		    (strncasecmp(val, fp->name,
				 char_after_equalsign - val) == 0)) {
			force_ent->param = *fp;
			force_ent->param.value = val_after_equalsign;
			return 0;
		}

		/*
		 * If val does not contain equal sign, allow shortcuts so that
		 * both 1.5 and 1.5Gbps work.
		 */
		if (strncasecmp(val, fp->name, strlen(val)))
			continue;

		nr_matches++;
		match_fp = fp;

		if (strcasecmp(val, fp->name) == 0) {
			nr_matches = 1;
			break;
		}
	}

	if (!nr_matches) {
		*reason = "unknown value";
		return -EINVAL;
	}
	if (nr_matches > 1) {
		*reason = "ambiguous value";
		return -EINVAL;
	}

	force_ent->param = *match_fp;

	return 0;
}

static void __init ata_parse_force_param(void)
{
	int idx = 0, size = 1;
	int last_port = -1, last_device = -1;
	char *p, *cur, *next;

	/* Calculate maximum number of params and allocate ata_force_tbl */
	for (p = ata_force_param_buf; *p; p++)
		if (*p == ',')
			size++;

	ata_force_tbl = kzalloc_objs(ata_force_tbl[0], size);
	if (!ata_force_tbl) {
		printk(KERN_WARNING "ata: failed to extend force table, "
		       "libata.force ignored\n");
		return;
	}

	/* parse and populate the table */
	for (cur = ata_force_param_buf; *cur != '\0'; cur = next) {
		const char *reason = "";
		struct ata_force_ent te = { .port = -1, .device = -1 };

		next = cur;
		if (ata_parse_force_one(&next, &te, &reason)) {
			printk(KERN_WARNING "ata: failed to parse force "
			       "parameter \"%s\" (%s)\n",
			       cur, reason);
			continue;
		}

		if (te.port == -1) {
			te.port = last_port;
			te.device = last_device;
		}

		ata_force_tbl[idx++] = te;

		last_port = te.port;
		last_device = te.device;
	}

	ata_force_tbl_size = idx;
}

static void ata_free_force_param(void)
{
	kfree(ata_force_tbl);
}
#else
static inline void ata_parse_force_param(void) { }
static inline void ata_free_force_param(void) { }
#endif

static int __init ata_init(void)
{
	int rc;

	ata_parse_force_param();

	rc = ata_sff_init();
	if (rc) {
		ata_free_force_param();
		return rc;
	}

	libata_transport_init();

	printk(KERN_DEBUG "libata version " DRV_VERSION " loaded.\n");

	return 0;
}

static void __exit ata_exit(void)
{
	libata_transport_exit();
	ata_sff_exit();
	ata_free_force_param();
}

subsys_initcall(ata_init);
module_exit(ata_exit);

static DEFINE_RATELIMIT_STATE(ratelimit, HZ / 5, 1);

int ata_ratelimit(void)
{
	return __ratelimit(&ratelimit);
}
EXPORT_SYMBOL_GPL(ata_ratelimit);

/**
 *	ata_msleep - ATA EH owner aware msleep
 *	@ap: ATA port to attribute the sleep to
 *	@msecs: duration to sleep in milliseconds
 *
 *	Sleeps @msecs.  If the current task is owner of @ap's EH, the
 *	ownership is released before going to sleep and reacquired
 *	after the sleep is complete.  IOW, other ports sharing the
 *	@ap->host will be allowed to own the EH while this task is
 *	sleeping.
 *
 *	LOCKING:
 *	Might sleep.
 */
void ata_msleep(struct ata_port *ap, unsigned int msecs)
	__context_unsafe(conditional locking)
{
	bool owns_eh = ap && ap->host->eh_owner == current;

	if (owns_eh)
		ata_eh_release(ap);

	if (msecs < 20) {
		unsigned long usecs = msecs * USEC_PER_MSEC;
		usleep_range(usecs, usecs + 50);
	} else {
		msleep(msecs);
	}

	if (owns_eh)
		ata_eh_acquire(ap);
}
EXPORT_SYMBOL_GPL(ata_msleep);

/**
 *	ata_wait_register - wait until register value changes
 *	@ap: ATA port to wait register for, can be NULL
 *	@reg: IO-mapped register
 *	@mask: Mask to apply to read register value
 *	@val: Wait condition
 *	@interval: polling interval in milliseconds
 *	@timeout: timeout in milliseconds
 *
 *	Waiting for some bits of register to change is a common
 *	operation for ATA controllers.  This function reads 32bit LE
 *	IO-mapped register @reg and tests for the following condition.
 *
 *	(*@reg & mask) != val
 *
 *	If the condition is met, it returns; otherwise, the process is
 *	repeated after @interval_msec until timeout.
 *
 *	LOCKING:
 *	Kernel thread context (may sleep)
 *
 *	RETURNS:
 *	The final register value.
 */
u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val,
		      unsigned int interval, unsigned int timeout)
{
	unsigned long deadline;
	u32 tmp;

	tmp = ioread32(reg);

	/* Calculate timeout _after_ the first read to make sure
	 * preceding writes reach the controller before starting to
	 * eat away the timeout.
	 */
	deadline = ata_deadline(jiffies, timeout);

	while ((tmp & mask) == val && time_before(jiffies, deadline)) {
		ata_msleep(ap, interval);
		tmp = ioread32(reg);
	}

	return tmp;
}
EXPORT_SYMBOL_GPL(ata_wait_register);

/*
 * Dummy port_ops
 */
static unsigned int ata_dummy_qc_issue(struct ata_queued_cmd *qc)
{
	return AC_ERR_SYSTEM;
}

static void ata_dummy_error_handler(struct ata_port *ap)
	__must_hold(&ap->host->eh_mutex)
{
	/* truly dummy */
}

struct ata_port_operations ata_dummy_port_ops = {
	.qc_issue		= ata_dummy_qc_issue,
	.error_handler		= ata_dummy_error_handler,
	.sched_eh		= ata_std_sched_eh,
	.end_eh			= ata_std_end_eh,
};
EXPORT_SYMBOL_GPL(ata_dummy_port_ops);

const struct ata_port_info ata_dummy_port_info = {
	.port_ops		= &ata_dummy_port_ops,
};
EXPORT_SYMBOL_GPL(ata_dummy_port_info);

EXPORT_TRACEPOINT_SYMBOL_GPL(ata_tf_load);
EXPORT_TRACEPOINT_SYMBOL_GPL(ata_exec_command);
EXPORT_TRACEPOINT_SYMBOL_GPL(ata_bmdma_setup);
EXPORT_TRACEPOINT_SYMBOL_GPL(ata_bmdma_start);
EXPORT_TRACEPOINT_SYMBOL_GPL(ata_bmdma_status);