spi: topcliff-pch: Convert to use master->max_speed_hz
Set "master->max_speed_hz = PCH_MAX_BAUDRATE" then we can remove pch_spi_setup.
In additional, pspi->max_speed_hz will never be 0 because it's default value
will be set to master->max_speed_hz.
Also remove list_empty checking in pch_spi_transfer() because the checking is
done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c
index 2e7f38c..6304c91 100644
--- a/drivers/spi/spi-topcliff-pch.c
+++ b/drivers/spi/spi-topcliff-pch.c
@@ -464,20 +464,6 @@
pch_spi_writereg(master, PCH_SRST, 0x0);
}
-static int pch_spi_setup(struct spi_device *pspi)
-{
- /* Check baud rate setting */
- /* if baud rate of chip is greater than
- max we can support,return error */
- if ((pspi->max_speed_hz) > PCH_MAX_BAUDRATE)
- pspi->max_speed_hz = PCH_MAX_BAUDRATE;
-
- dev_dbg(&pspi->dev, "%s MODE = %x\n", __func__,
- (pspi->mode) & (SPI_CPOL | SPI_CPHA));
-
- return 0;
-}
-
static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg)
{
@@ -486,23 +472,6 @@
int retval;
unsigned long flags;
- /* validate spi message and baud rate */
- if (unlikely(list_empty(&pmsg->transfers) == 1)) {
- dev_err(&pspi->dev, "%s list empty\n", __func__);
- retval = -EINVAL;
- goto err_out;
- }
-
- if (unlikely(pspi->max_speed_hz == 0)) {
- dev_err(&pspi->dev, "%s pch_spi_transfer maxspeed=%d\n",
- __func__, pspi->max_speed_hz);
- retval = -EINVAL;
- goto err_out;
- }
-
- dev_dbg(&pspi->dev,
- "%s Transfer List not empty. Transfer Speed is set.\n", __func__);
-
spin_lock_irqsave(&data->lock, flags);
/* validate Tx/Rx buffers and Transfer length */
list_for_each_entry(transfer, &pmsg->transfers, transfer_list) {
@@ -523,10 +492,6 @@
dev_dbg(&pspi->dev,
"%s Tx/Rx buffer valid. Transfer length valid\n",
__func__);
-
- /* if baud rate has been specified validate the same */
- if (transfer->speed_hz > PCH_MAX_BAUDRATE)
- transfer->speed_hz = PCH_MAX_BAUDRATE;
}
spin_unlock_irqrestore(&data->lock, flags);
@@ -1418,10 +1383,10 @@
/* initialize members of SPI master */
master->num_chipselect = PCH_MAX_CS;
- master->setup = pch_spi_setup;
master->transfer = pch_spi_transfer;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;
master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
+ master->max_speed_hz = PCH_MAX_BAUDRATE;
data->board_dat = board_dat;
data->plat_dev = plat_dev;
