| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| /* |
| * RapidIO register definitions |
| * |
| * Copyright 2005 MontaVista Software, Inc. |
| * Matt Porter <mporter@kernel.crashing.org> |
| */ |
| |
| #ifndef LINUX_RIO_REGS_H |
| #define LINUX_RIO_REGS_H |
| |
| /* |
| * In RapidIO, each device has a 16MB configuration space that is |
| * accessed via maintenance transactions. Portions of configuration |
| * space are standardized and/or reserved. |
| */ |
| #define RIO_MAINT_SPACE_SZ 0x1000000 /* 16MB of RapidIO mainenance space */ |
| |
| #define RIO_DEV_ID_CAR 0x00 /* [I] Device Identity CAR */ |
| #define RIO_DEV_INFO_CAR 0x04 /* [I] Device Information CAR */ |
| #define RIO_ASM_ID_CAR 0x08 /* [I] Assembly Identity CAR */ |
| #define RIO_ASM_ID_MASK 0xffff0000 /* [I] Asm ID Mask */ |
| #define RIO_ASM_VEN_ID_MASK 0x0000ffff /* [I] Asm Vend Mask */ |
| |
| #define RIO_ASM_INFO_CAR 0x0c /* [I] Assembly Information CAR */ |
| #define RIO_ASM_REV_MASK 0xffff0000 /* [I] Asm Rev Mask */ |
| #define RIO_EXT_FTR_PTR_MASK 0x0000ffff /* [I] EF_PTR Mask */ |
| |
| #define RIO_PEF_CAR 0x10 /* [I] Processing Element Features CAR */ |
| #define RIO_PEF_BRIDGE 0x80000000 /* [I] Bridge */ |
| #define RIO_PEF_MEMORY 0x40000000 /* [I] MMIO */ |
| #define RIO_PEF_PROCESSOR 0x20000000 /* [I] Processor */ |
| #define RIO_PEF_SWITCH 0x10000000 /* [I] Switch */ |
| #define RIO_PEF_MULTIPORT 0x08000000 /* [VI, 2.1] Multiport */ |
| #define RIO_PEF_INB_MBOX 0x00f00000 /* [II, <= 1.2] Mailboxes */ |
| #define RIO_PEF_INB_MBOX0 0x00800000 /* [II, <= 1.2] Mailbox 0 */ |
| #define RIO_PEF_INB_MBOX1 0x00400000 /* [II, <= 1.2] Mailbox 1 */ |
| #define RIO_PEF_INB_MBOX2 0x00200000 /* [II, <= 1.2] Mailbox 2 */ |
| #define RIO_PEF_INB_MBOX3 0x00100000 /* [II, <= 1.2] Mailbox 3 */ |
| #define RIO_PEF_INB_DOORBELL 0x00080000 /* [II, <= 1.2] Doorbells */ |
| #define RIO_PEF_DEV32 0x00001000 /* [III] PE supports Common TRansport Dev32 */ |
| #define RIO_PEF_EXT_RT 0x00000200 /* [III, 1.3] Extended route table support */ |
| #define RIO_PEF_STD_RT 0x00000100 /* [III, 1.3] Standard route table support */ |
| #define RIO_PEF_CTLS 0x00000010 /* [III] Common Transport Large System (< rev.3) */ |
| #define RIO_PEF_DEV16 0x00000010 /* [III] PE Supports Common Transport Dev16 (rev.3) */ |
| #define RIO_PEF_EXT_FEATURES 0x00000008 /* [I] EFT_PTR valid */ |
| #define RIO_PEF_ADDR_66 0x00000004 /* [I] 66 bits */ |
| #define RIO_PEF_ADDR_50 0x00000002 /* [I] 50 bits */ |
| #define RIO_PEF_ADDR_34 0x00000001 /* [I] 34 bits */ |
| |
| #define RIO_SWP_INFO_CAR 0x14 /* [I] Switch Port Information CAR */ |
| #define RIO_SWP_INFO_PORT_TOTAL_MASK 0x0000ff00 /* [I] Total number of ports */ |
| #define RIO_SWP_INFO_PORT_NUM_MASK 0x000000ff /* [I] Maintenance transaction port number */ |
| #define RIO_GET_TOTAL_PORTS(x) ((x & RIO_SWP_INFO_PORT_TOTAL_MASK) >> 8) |
| #define RIO_GET_PORT_NUM(x) (x & RIO_SWP_INFO_PORT_NUM_MASK) |
| |
| #define RIO_SRC_OPS_CAR 0x18 /* [I] Source Operations CAR */ |
| #define RIO_SRC_OPS_READ 0x00008000 /* [I] Read op */ |
| #define RIO_SRC_OPS_WRITE 0x00004000 /* [I] Write op */ |
| #define RIO_SRC_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ |
| #define RIO_SRC_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ |
| #define RIO_SRC_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ |
| #define RIO_SRC_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ |
| #define RIO_SRC_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ |
| #define RIO_SRC_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ |
| #define RIO_SRC_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ |
| #define RIO_SRC_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ |
| #define RIO_SRC_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ |
| #define RIO_SRC_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ |
| |
| #define RIO_DST_OPS_CAR 0x1c /* Destination Operations CAR */ |
| #define RIO_DST_OPS_READ 0x00008000 /* [I] Read op */ |
| #define RIO_DST_OPS_WRITE 0x00004000 /* [I] Write op */ |
| #define RIO_DST_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ |
| #define RIO_DST_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ |
| #define RIO_DST_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ |
| #define RIO_DST_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ |
| #define RIO_DST_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ |
| #define RIO_DST_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ |
| #define RIO_DST_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ |
| #define RIO_DST_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ |
| #define RIO_DST_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ |
| #define RIO_DST_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ |
| |
| #define RIO_OPS_READ 0x00008000 /* [I] Read op */ |
| #define RIO_OPS_WRITE 0x00004000 /* [I] Write op */ |
| #define RIO_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ |
| #define RIO_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ |
| #define RIO_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ |
| #define RIO_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ |
| #define RIO_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ |
| #define RIO_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ |
| #define RIO_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ |
| #define RIO_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ |
| #define RIO_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ |
| #define RIO_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ |
| |
| /* 0x20-0x30 *//* Reserved */ |
| |
| #define RIO_SWITCH_RT_LIMIT 0x34 /* [III, 1.3] Switch Route Table Destination ID Limit CAR */ |
| #define RIO_RT_MAX_DESTID 0x0000ffff |
| |
| #define RIO_MBOX_CSR 0x40 /* [II, <= 1.2] Mailbox CSR */ |
| #define RIO_MBOX0_AVAIL 0x80000000 /* [II] Mbox 0 avail */ |
| #define RIO_MBOX0_FULL 0x40000000 /* [II] Mbox 0 full */ |
| #define RIO_MBOX0_EMPTY 0x20000000 /* [II] Mbox 0 empty */ |
| #define RIO_MBOX0_BUSY 0x10000000 /* [II] Mbox 0 busy */ |
| #define RIO_MBOX0_FAIL 0x08000000 /* [II] Mbox 0 fail */ |
| #define RIO_MBOX0_ERROR 0x04000000 /* [II] Mbox 0 error */ |
| #define RIO_MBOX1_AVAIL 0x00800000 /* [II] Mbox 1 avail */ |
| #define RIO_MBOX1_FULL 0x00200000 /* [II] Mbox 1 full */ |
| #define RIO_MBOX1_EMPTY 0x00200000 /* [II] Mbox 1 empty */ |
| #define RIO_MBOX1_BUSY 0x00100000 /* [II] Mbox 1 busy */ |
| #define RIO_MBOX1_FAIL 0x00080000 /* [II] Mbox 1 fail */ |
| #define RIO_MBOX1_ERROR 0x00040000 /* [II] Mbox 1 error */ |
| #define RIO_MBOX2_AVAIL 0x00008000 /* [II] Mbox 2 avail */ |
| #define RIO_MBOX2_FULL 0x00004000 /* [II] Mbox 2 full */ |
| #define RIO_MBOX2_EMPTY 0x00002000 /* [II] Mbox 2 empty */ |
| #define RIO_MBOX2_BUSY 0x00001000 /* [II] Mbox 2 busy */ |
| #define RIO_MBOX2_FAIL 0x00000800 /* [II] Mbox 2 fail */ |
| #define RIO_MBOX2_ERROR 0x00000400 /* [II] Mbox 2 error */ |
| #define RIO_MBOX3_AVAIL 0x00000080 /* [II] Mbox 3 avail */ |
| #define RIO_MBOX3_FULL 0x00000040 /* [II] Mbox 3 full */ |
| #define RIO_MBOX3_EMPTY 0x00000020 /* [II] Mbox 3 empty */ |
| #define RIO_MBOX3_BUSY 0x00000010 /* [II] Mbox 3 busy */ |
| #define RIO_MBOX3_FAIL 0x00000008 /* [II] Mbox 3 fail */ |
| #define RIO_MBOX3_ERROR 0x00000004 /* [II] Mbox 3 error */ |
| |
| #define RIO_WRITE_PORT_CSR 0x44 /* [I, <= 1.2] Write Port CSR */ |
| #define RIO_DOORBELL_CSR 0x44 /* [II, <= 1.2] Doorbell CSR */ |
| #define RIO_DOORBELL_AVAIL 0x80000000 /* [II] Doorbell avail */ |
| #define RIO_DOORBELL_FULL 0x40000000 /* [II] Doorbell full */ |
| #define RIO_DOORBELL_EMPTY 0x20000000 /* [II] Doorbell empty */ |
| #define RIO_DOORBELL_BUSY 0x10000000 /* [II] Doorbell busy */ |
| #define RIO_DOORBELL_FAILED 0x08000000 /* [II] Doorbell failed */ |
| #define RIO_DOORBELL_ERROR 0x04000000 /* [II] Doorbell error */ |
| #define RIO_WRITE_PORT_AVAILABLE 0x00000080 /* [I] Write Port Available */ |
| #define RIO_WRITE_PORT_FULL 0x00000040 /* [I] Write Port Full */ |
| #define RIO_WRITE_PORT_EMPTY 0x00000020 /* [I] Write Port Empty */ |
| #define RIO_WRITE_PORT_BUSY 0x00000010 /* [I] Write Port Busy */ |
| #define RIO_WRITE_PORT_FAILED 0x00000008 /* [I] Write Port Failed */ |
| #define RIO_WRITE_PORT_ERROR 0x00000004 /* [I] Write Port Error */ |
| |
| /* 0x48 *//* Reserved */ |
| |
| #define RIO_PELL_CTRL_CSR 0x4c /* [I] PE Logical Layer Control CSR */ |
| #define RIO_PELL_ADDR_66 0x00000004 /* [I] 66-bit addr */ |
| #define RIO_PELL_ADDR_50 0x00000002 /* [I] 50-bit addr */ |
| #define RIO_PELL_ADDR_34 0x00000001 /* [I] 34-bit addr */ |
| |
| /* 0x50-0x54 *//* Reserved */ |
| |
| #define RIO_LCSH_BA 0x58 /* [I] LCS High Base Address */ |
| #define RIO_LCSL_BA 0x5c /* [I] LCS Base Address */ |
| |
| #define RIO_DID_CSR 0x60 /* [III] Base Device ID CSR */ |
| |
| /* 0x64 *//* Reserved */ |
| |
| #define RIO_HOST_DID_LOCK_CSR 0x68 /* [III] Host Base Device ID Lock CSR */ |
| #define RIO_COMPONENT_TAG_CSR 0x6c /* [III] Component Tag CSR */ |
| |
| #define RIO_STD_RTE_CONF_DESTID_SEL_CSR 0x70 |
| #define RIO_STD_RTE_CONF_EXTCFGEN 0x80000000 |
| #define RIO_STD_RTE_CONF_PORT_SEL_CSR 0x74 |
| #define RIO_STD_RTE_DEFAULT_PORT 0x78 |
| |
| /* 0x7c-0xf8 *//* Reserved */ |
| /* 0x100-0xfff8 *//* [I] Extended Features Space */ |
| /* 0x10000-0xfffff8 *//* [I] Implementation-defined Space */ |
| |
| /* |
| * Extended Features Space is a configuration space area where |
| * functionality is mapped into extended feature blocks via a |
| * singly linked list of extended feature pointers (EFT_PTR). |
| * |
| * Each extended feature block can be identified/located in |
| * Extended Features Space by walking the extended feature |
| * list starting with the Extended Feature Pointer located |
| * in the Assembly Information CAR. |
| * |
| * Extended Feature Blocks (EFBs) are identified with an assigned |
| * EFB ID. Extended feature block offsets in the definitions are |
| * relative to the offset of the EFB within the Extended Features |
| * Space. |
| */ |
| |
| /* Helper macros to parse the Extended Feature Block header */ |
| #define RIO_EFB_PTR_MASK 0xffff0000 |
| #define RIO_EFB_ID_MASK 0x0000ffff |
| #define RIO_GET_BLOCK_PTR(x) ((x & RIO_EFB_PTR_MASK) >> 16) |
| #define RIO_GET_BLOCK_ID(x) (x & RIO_EFB_ID_MASK) |
| |
| /* Extended Feature Block IDs */ |
| #define RIO_EFB_SER_EP_M1_ID 0x0001 /* [VI] LP-Serial EP Devices, Map I */ |
| #define RIO_EFB_SER_EP_SW_M1_ID 0x0002 /* [VI] LP-Serial EP w SW Recovery Devices, Map I */ |
| #define RIO_EFB_SER_EPF_M1_ID 0x0003 /* [VI] LP-Serial EP Free Devices, Map I */ |
| #define RIO_EFB_SER_EP_ID 0x0004 /* [VI] LP-Serial EP Devices, RIO 1.2 */ |
| #define RIO_EFB_SER_EP_REC_ID 0x0005 /* [VI] LP-Serial EP w SW Recovery Devices, RIO 1.2 */ |
| #define RIO_EFB_SER_EP_FREE_ID 0x0006 /* [VI] LP-Serial EP Free Devices, RIO 1.2 */ |
| #define RIO_EFB_ERR_MGMNT 0x0007 /* [VIII] Error Management Extensions */ |
| #define RIO_EFB_SER_EPF_SW_M1_ID 0x0009 /* [VI] LP-Serial EP Free w SW Recovery Devices, Map I */ |
| #define RIO_EFB_SW_ROUTING_TBL 0x000E /* [III] Switch Routing Table Block */ |
| #define RIO_EFB_SER_EP_M2_ID 0x0011 /* [VI] LP-Serial EP Devices, Map II */ |
| #define RIO_EFB_SER_EP_SW_M2_ID 0x0012 /* [VI] LP-Serial EP w SW Recovery Devices, Map II */ |
| #define RIO_EFB_SER_EPF_M2_ID 0x0013 /* [VI] LP-Serial EP Free Devices, Map II */ |
| #define RIO_EFB_ERR_MGMNT_HS 0x0017 /* [VIII] Error Management Extensions, Hot-Swap only */ |
| #define RIO_EFB_SER_EPF_SW_M2_ID 0x0019 /* [VI] LP-Serial EP Free w SW Recovery Devices, Map II */ |
| |
| /* |
| * Physical LP-Serial Registers Definitions |
| * Parameters in register macros: |
| * n - port number, m - Register Map Type (1 or 2) |
| */ |
| #define RIO_PORT_MNT_HEADER 0x0000 |
| #define RIO_PORT_REQ_CTL_CSR 0x0020 |
| #define RIO_PORT_RSP_CTL_CSR 0x0024 |
| #define RIO_PORT_LINKTO_CTL_CSR 0x0020 |
| #define RIO_PORT_RSPTO_CTL_CSR 0x0024 |
| #define RIO_PORT_GEN_CTL_CSR 0x003c |
| #define RIO_PORT_GEN_HOST 0x80000000 |
| #define RIO_PORT_GEN_MASTER 0x40000000 |
| #define RIO_PORT_GEN_DISCOVERED 0x20000000 |
| #define RIO_PORT_N_MNT_REQ_CSR(n, m) (0x40 + (n) * (0x20 * (m))) |
| #define RIO_MNT_REQ_CMD_RD 0x03 /* Reset-device command */ |
| #define RIO_MNT_REQ_CMD_IS 0x04 /* Input-status command */ |
| #define RIO_PORT_N_MNT_RSP_CSR(n, m) (0x44 + (n) * (0x20 * (m))) |
| #define RIO_PORT_N_MNT_RSP_RVAL 0x80000000 /* Response Valid */ |
| #define RIO_PORT_N_MNT_RSP_ASTAT 0x000007e0 /* ackID Status */ |
| #define RIO_PORT_N_MNT_RSP_LSTAT 0x0000001f /* Link Status */ |
| #define RIO_PORT_N_ACK_STS_CSR(n) (0x48 + (n) * 0x20) /* Only in RM-I */ |
| #define RIO_PORT_N_ACK_CLEAR 0x80000000 |
| #define RIO_PORT_N_ACK_INBOUND 0x3f000000 |
| #define RIO_PORT_N_ACK_OUTSTAND 0x00003f00 |
| #define RIO_PORT_N_ACK_OUTBOUND 0x0000003f |
| #define RIO_PORT_N_CTL2_CSR(n, m) (0x54 + (n) * (0x20 * (m))) |
| #define RIO_PORT_N_CTL2_SEL_BAUD 0xf0000000 |
| #define RIO_PORT_N_ERR_STS_CSR(n, m) (0x58 + (n) * (0x20 * (m))) |
| #define RIO_PORT_N_ERR_STS_OUT_ES 0x00010000 /* Output Error-stopped */ |
| #define RIO_PORT_N_ERR_STS_INP_ES 0x00000100 /* Input Error-stopped */ |
| #define RIO_PORT_N_ERR_STS_PW_PEND 0x00000010 /* Port-Write Pending */ |
| #define RIO_PORT_N_ERR_STS_PORT_UA 0x00000008 /* Port Unavailable */ |
| #define RIO_PORT_N_ERR_STS_PORT_ERR 0x00000004 |
| #define RIO_PORT_N_ERR_STS_PORT_OK 0x00000002 |
| #define RIO_PORT_N_ERR_STS_PORT_UNINIT 0x00000001 |
| #define RIO_PORT_N_CTL_CSR(n, m) (0x5c + (n) * (0x20 * (m))) |
| #define RIO_PORT_N_CTL_PWIDTH 0xc0000000 |
| #define RIO_PORT_N_CTL_PWIDTH_1 0x00000000 |
| #define RIO_PORT_N_CTL_PWIDTH_4 0x40000000 |
| #define RIO_PORT_N_CTL_IPW 0x38000000 /* Initialized Port Width */ |
| #define RIO_PORT_N_CTL_P_TYP_SER 0x00000001 |
| #define RIO_PORT_N_CTL_LOCKOUT 0x00000002 |
| #define RIO_PORT_N_CTL_EN_RX 0x00200000 |
| #define RIO_PORT_N_CTL_EN_TX 0x00400000 |
| #define RIO_PORT_N_OB_ACK_CSR(n) (0x60 + (n) * 0x40) /* Only in RM-II */ |
| #define RIO_PORT_N_OB_ACK_CLEAR 0x80000000 |
| #define RIO_PORT_N_OB_ACK_OUTSTD 0x00fff000 |
| #define RIO_PORT_N_OB_ACK_OUTBND 0x00000fff |
| #define RIO_PORT_N_IB_ACK_CSR(n) (0x64 + (n) * 0x40) /* Only in RM-II */ |
| #define RIO_PORT_N_IB_ACK_INBND 0x00000fff |
| |
| /* |
| * Device-based helper macros for serial port register access. |
| * d - pointer to rapidio device object, n - port number |
| */ |
| |
| #define RIO_DEV_PORT_N_MNT_REQ_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_MNT_REQ_CSR(n, d->phys_rmap)) |
| |
| #define RIO_DEV_PORT_N_MNT_RSP_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_MNT_RSP_CSR(n, d->phys_rmap)) |
| |
| #define RIO_DEV_PORT_N_ACK_STS_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_ACK_STS_CSR(n)) |
| |
| #define RIO_DEV_PORT_N_CTL2_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_CTL2_CSR(n, d->phys_rmap)) |
| |
| #define RIO_DEV_PORT_N_ERR_STS_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_ERR_STS_CSR(n, d->phys_rmap)) |
| |
| #define RIO_DEV_PORT_N_CTL_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_CTL_CSR(n, d->phys_rmap)) |
| |
| #define RIO_DEV_PORT_N_OB_ACK_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_OB_ACK_CSR(n)) |
| |
| #define RIO_DEV_PORT_N_IB_ACK_CSR(d, n) \ |
| (d->phys_efptr + RIO_PORT_N_IB_ACK_CSR(n)) |
| |
| /* |
| * Error Management Extensions (RapidIO 1.3+, Part 8) |
| * |
| * Extended Features Block ID=0x0007 |
| */ |
| |
| /* General EM Registers (Common for all Ports) */ |
| |
| #define RIO_EM_EFB_HEADER 0x000 /* Error Management Extensions Block Header */ |
| #define RIO_EM_EMHS_CAR 0x004 /* EM Functionality CAR */ |
| #define RIO_EM_LTL_ERR_DETECT 0x008 /* Logical/Transport Layer Error Detect CSR */ |
| #define RIO_EM_LTL_ERR_EN 0x00c /* Logical/Transport Layer Error Enable CSR */ |
| #define REM_LTL_ERR_ILLTRAN 0x08000000 /* Illegal Transaction decode */ |
| #define REM_LTL_ERR_UNSOLR 0x00800000 /* Unsolicited Response */ |
| #define REM_LTL_ERR_UNSUPTR 0x00400000 /* Unsupported Transaction */ |
| #define REM_LTL_ERR_IMPSPEC 0x000000ff /* Implementation Specific */ |
| #define RIO_EM_LTL_HIADDR_CAP 0x010 /* Logical/Transport Layer High Address Capture CSR */ |
| #define RIO_EM_LTL_ADDR_CAP 0x014 /* Logical/Transport Layer Address Capture CSR */ |
| #define RIO_EM_LTL_DEVID_CAP 0x018 /* Logical/Transport Layer Device ID Capture CSR */ |
| #define RIO_EM_LTL_CTRL_CAP 0x01c /* Logical/Transport Layer Control Capture CSR */ |
| #define RIO_EM_LTL_DID32_CAP 0x020 /* Logical/Transport Layer Dev32 DestID Capture CSR */ |
| #define RIO_EM_LTL_SID32_CAP 0x024 /* Logical/Transport Layer Dev32 source ID Capture CSR */ |
| #define RIO_EM_PW_TGT_DEVID 0x028 /* Port-write Target deviceID CSR */ |
| #define RIO_EM_PW_TGT_DEVID_D16M 0xff000000 /* Port-write Target DID16 MSB */ |
| #define RIO_EM_PW_TGT_DEVID_D8 0x00ff0000 /* Port-write Target DID16 LSB or DID8 */ |
| #define RIO_EM_PW_TGT_DEVID_DEV16 0x00008000 /* Port-write Target DID16 LSB or DID8 */ |
| #define RIO_EM_PW_TGT_DEVID_DEV32 0x00004000 /* Port-write Target DID16 LSB or DID8 */ |
| #define RIO_EM_PKT_TTL 0x02c /* Packet Time-to-live CSR */ |
| #define RIO_EM_PKT_TTL_VAL 0xffff0000 /* Packet Time-to-live value */ |
| #define RIO_EM_PW_TGT32_DEVID 0x030 /* Port-write Dev32 Target deviceID CSR */ |
| #define RIO_EM_PW_TX_CTRL 0x034 /* Port-write Transmission Control CSR */ |
| #define RIO_EM_PW_TX_CTRL_PW_DIS 0x00000001 /* Port-write Transmission Disable bit */ |
| |
| /* Per-Port EM Registers */ |
| |
| #define RIO_EM_PN_ERR_DETECT(x) (0x040 + x*0x40) /* Port N Error Detect CSR */ |
| #define REM_PED_IMPL_SPEC 0x80000000 |
| #define REM_PED_LINK_OK2U 0x40000000 /* Link OK to Uninit transition */ |
| #define REM_PED_LINK_UPDA 0x20000000 /* Link Uninit Packet Discard Active */ |
| #define REM_PED_LINK_U2OK 0x10000000 /* Link Uninit to OK transition */ |
| #define REM_PED_LINK_TO 0x00000001 |
| |
| #define RIO_EM_PN_ERRRATE_EN(x) (0x044 + x*0x40) /* Port N Error Rate Enable CSR */ |
| #define RIO_EM_PN_ERRRATE_EN_OK2U 0x40000000 /* Enable notification for OK2U */ |
| #define RIO_EM_PN_ERRRATE_EN_UPDA 0x20000000 /* Enable notification for UPDA */ |
| #define RIO_EM_PN_ERRRATE_EN_U2OK 0x10000000 /* Enable notification for U2OK */ |
| |
| #define RIO_EM_PN_ATTRIB_CAP(x) (0x048 + x*0x40) /* Port N Attributes Capture CSR */ |
| #define RIO_EM_PN_PKT_CAP_0(x) (0x04c + x*0x40) /* Port N Packet/Control Symbol Capture 0 CSR */ |
| #define RIO_EM_PN_PKT_CAP_1(x) (0x050 + x*0x40) /* Port N Packet Capture 1 CSR */ |
| #define RIO_EM_PN_PKT_CAP_2(x) (0x054 + x*0x40) /* Port N Packet Capture 2 CSR */ |
| #define RIO_EM_PN_PKT_CAP_3(x) (0x058 + x*0x40) /* Port N Packet Capture 3 CSR */ |
| #define RIO_EM_PN_ERRRATE(x) (0x068 + x*0x40) /* Port N Error Rate CSR */ |
| #define RIO_EM_PN_ERRRATE_TR(x) (0x06c + x*0x40) /* Port N Error Rate Threshold CSR */ |
| #define RIO_EM_PN_LINK_UDT(x) (0x070 + x*0x40) /* Port N Link Uninit Discard Timer CSR */ |
| #define RIO_EM_PN_LINK_UDT_TO 0xffffff00 /* Link Uninit Timeout value */ |
| |
| /* |
| * Switch Routing Table Register Block ID=0x000E (RapidIO 3.0+, part 3) |
| * Register offsets are defined from beginning of the block. |
| */ |
| |
| /* Broadcast Routing Table Control CSR */ |
| #define RIO_BC_RT_CTL_CSR 0x020 |
| #define RIO_RT_CTL_THREE_LVL 0x80000000 |
| #define RIO_RT_CTL_DEV32_RT_CTRL 0x40000000 |
| #define RIO_RT_CTL_MC_MASK_SZ 0x03000000 /* 3.0+ Part 11: Multicast */ |
| |
| /* Broadcast Level 0 Info CSR */ |
| #define RIO_BC_RT_LVL0_INFO_CSR 0x030 |
| #define RIO_RT_L0I_NUM_GR 0xff000000 |
| #define RIO_RT_L0I_GR_PTR 0x00fffc00 |
| |
| /* Broadcast Level 1 Info CSR */ |
| #define RIO_BC_RT_LVL1_INFO_CSR 0x034 |
| #define RIO_RT_L1I_NUM_GR 0xff000000 |
| #define RIO_RT_L1I_GR_PTR 0x00fffc00 |
| |
| /* Broadcast Level 2 Info CSR */ |
| #define RIO_BC_RT_LVL2_INFO_CSR 0x038 |
| #define RIO_RT_L2I_NUM_GR 0xff000000 |
| #define RIO_RT_L2I_GR_PTR 0x00fffc00 |
| |
| /* Per-Port Routing Table registers. |
| * Register fields defined in the broadcast section above are |
| * applicable to the corresponding registers below. |
| */ |
| #define RIO_SPx_RT_CTL_CSR(x) (0x040 + (0x20 * x)) |
| #define RIO_SPx_RT_LVL0_INFO_CSR(x) (0x50 + (0x20 * x)) |
| #define RIO_SPx_RT_LVL1_INFO_CSR(x) (0x54 + (0x20 * x)) |
| #define RIO_SPx_RT_LVL2_INFO_CSR(x) (0x58 + (0x20 * x)) |
| |
| /* Register Formats for Routing Table Group entry. |
| * Register offsets are calculated using GR_PTR field in the corresponding |
| * table Level_N and group/entry numbers (see RapidIO 3.0+ Part 3). |
| */ |
| #define RIO_RT_Ln_ENTRY_IMPL_DEF 0xf0000000 |
| #define RIO_RT_Ln_ENTRY_RTE_VAL 0x000003ff |
| #define RIO_RT_ENTRY_DROP_PKT 0x300 |
| |
| #endif /* LINUX_RIO_REGS_H */ |