drivers/spi/spi-dw-dma.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Special handling for DW DMA core
 *
 * Copyright (c) 2009, 2014 Intel Corporation.
 */

#include <linux/completion.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/irqreturn.h>
#include <linux/jiffies.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/platform_data/dma-dw.h>
#include <linux/spi/spi.h>
#include <linux/types.h>

#include "spi-dw.h"

#define DW_SPI_RX_BUSY		0
#define DW_SPI_RX_BURST_LEVEL	16
#define DW_SPI_TX_BUSY		1
#define DW_SPI_TX_BURST_LEVEL	16

static bool dw_spi_dma_chan_filter(struct dma_chan *chan, void *param)
{
	struct dw_dma_slave *s = param;

	if (s->dma_dev != chan->device->dev)
		return false;

	chan->private = s;
	return true;
}

static void dw_spi_dma_maxburst_init(struct dw_spi *dws)
{
	struct dma_slave_caps caps;
	u32 max_burst, def_burst;
	int ret;

	def_burst = dws->fifo_len / 2;

	ret = dma_get_slave_caps(dws->rxchan, &caps);
	if (!ret && caps.max_burst)
		max_burst = caps.max_burst;
	else
		max_burst = DW_SPI_RX_BURST_LEVEL;

	dws->rxburst = min(max_burst, def_burst);
	dw_writel(dws, DW_SPI_DMARDLR, dws->rxburst - 1);

	ret = dma_get_slave_caps(dws->txchan, &caps);
	if (!ret && caps.max_burst)
		max_burst = caps.max_burst;
	else
		max_burst = DW_SPI_TX_BURST_LEVEL;

	/*
	 * Having a Rx DMA channel serviced with higher priority than a Tx DMA
	 * channel might not be enough to provide a well balanced DMA-based
	 * SPI transfer interface. There might still be moments when the Tx DMA
	 * channel is occasionally handled faster than the Rx DMA channel.
	 * That in its turn will eventually cause the SPI Rx FIFO overflow if
	 * SPI bus speed is high enough to fill the SPI Rx FIFO in before it's
	 * cleared by the Rx DMA channel. In order to fix the problem the Tx
	 * DMA activity is intentionally slowed down by limiting the SPI Tx
	 * FIFO depth with a value twice bigger than the Tx burst length.
	 */
	dws->txburst = min(max_burst, def_burst);
	dw_writel(dws, DW_SPI_DMATDLR, dws->txburst);
}

static int dw_spi_dma_caps_init(struct dw_spi *dws)
{
	struct dma_slave_caps tx, rx;
	int ret;

	ret = dma_get_slave_caps(dws->txchan, &tx);
	if (ret)
		return ret;

	ret = dma_get_slave_caps(dws->rxchan, &rx);
	if (ret)
		return ret;

	if (!(tx.directions & BIT(DMA_MEM_TO_DEV) &&
	      rx.directions & BIT(DMA_DEV_TO_MEM)))
		return -ENXIO;

	if (tx.max_sg_burst > 0 && rx.max_sg_burst > 0)
		dws->dma_sg_burst = min(tx.max_sg_burst, rx.max_sg_burst);
	else if (tx.max_sg_burst > 0)
		dws->dma_sg_burst = tx.max_sg_burst;
	else if (rx.max_sg_burst > 0)
		dws->dma_sg_burst = rx.max_sg_burst;
	else
		dws->dma_sg_burst = 0;

	/*
	 * Assuming both channels belong to the same DMA controller hence the
	 * peripheral side address width capabilities most likely would be
	 * the same.
	 */
	dws->dma_addr_widths = tx.dst_addr_widths & rx.src_addr_widths;

	return 0;
}

static int dw_spi_dma_init_mfld(struct device *dev, struct dw_spi *dws)
{
	struct dw_dma_slave dma_tx = { .dst_id = 1 }, *tx = &dma_tx;
	struct dw_dma_slave dma_rx = { .src_id = 0 }, *rx = &dma_rx;
	struct pci_dev *dma_dev;
	dma_cap_mask_t mask;
	int ret = -EBUSY;

	/*
	 * Get pci device for DMA controller, currently it could only
	 * be the DMA controller of Medfield
	 */
	dma_dev = pci_get_device(PCI_VENDOR_ID_INTEL, 0x0827, NULL);
	if (!dma_dev)
		return -ENODEV;

	dma_cap_zero(mask);
	dma_cap_set(DMA_SLAVE, mask);

	/* 1. Init rx channel */
	rx->dma_dev = &dma_dev->dev;
	dws->rxchan = dma_request_channel(mask, dw_spi_dma_chan_filter, rx);
	if (!dws->rxchan)
		goto err_exit;

	/* 2. Init tx channel */
	tx->dma_dev = &dma_dev->dev;
	dws->txchan = dma_request_channel(mask, dw_spi_dma_chan_filter, tx);
	if (!dws->txchan)
		goto free_rxchan;

	dws->host->dma_rx = dws->rxchan;
	dws->host->dma_tx = dws->txchan;

	init_completion(&dws->dma_completion);

	ret = dw_spi_dma_caps_init(dws);
	if (ret)
		goto free_txchan;

	dw_spi_dma_maxburst_init(dws);

	pci_dev_put(dma_dev);

	return 0;

free_txchan:
	dma_release_channel(dws->txchan);
	dws->txchan = NULL;
free_rxchan:
	dma_release_channel(dws->rxchan);
	dws->rxchan = NULL;
err_exit:
	pci_dev_put(dma_dev);
	return ret;
}

static int dw_spi_dma_init_generic(struct device *dev, struct dw_spi *dws)
{
	int ret;

	dws->rxchan = dma_request_chan(dev, "rx");
	if (IS_ERR(dws->rxchan)) {
		ret = PTR_ERR(dws->rxchan);
		dws->rxchan = NULL;
		goto err_exit;
	}

	dws->txchan = dma_request_chan(dev, "tx");
	if (IS_ERR(dws->txchan)) {
		ret = PTR_ERR(dws->txchan);
		dws->txchan = NULL;
		goto free_rxchan;
	}

	dws->host->dma_rx = dws->rxchan;
	dws->host->dma_tx = dws->txchan;

	init_completion(&dws->dma_completion);

	ret = dw_spi_dma_caps_init(dws);
	if (ret)
		goto free_txchan;

	dw_spi_dma_maxburst_init(dws);

	return 0;

free_txchan:
	dma_release_channel(dws->txchan);
	dws->txchan = NULL;
free_rxchan:
	dma_release_channel(dws->rxchan);
	dws->rxchan = NULL;
err_exit:
	return ret;
}

static void dw_spi_dma_exit(struct dw_spi *dws)
{
	if (dws->txchan) {
		dmaengine_terminate_sync(dws->txchan);
		dma_release_channel(dws->txchan);
	}

	if (dws->rxchan) {
		dmaengine_terminate_sync(dws->rxchan);
		dma_release_channel(dws->rxchan);
	}
}

static irqreturn_t dw_spi_dma_transfer_handler(struct dw_spi *dws)
{
	dw_spi_check_status(dws, false);

	complete(&dws->dma_completion);

	return IRQ_HANDLED;
}

static enum dma_slave_buswidth dw_spi_dma_convert_width(u8 n_bytes)
{
	switch (n_bytes) {
	case 1:
		return DMA_SLAVE_BUSWIDTH_1_BYTE;
	case 2:
		return DMA_SLAVE_BUSWIDTH_2_BYTES;
	case 4:
		return DMA_SLAVE_BUSWIDTH_4_BYTES;
	default:
		return DMA_SLAVE_BUSWIDTH_UNDEFINED;
	}
}

static bool dw_spi_can_dma(struct spi_controller *host,
			   struct spi_device *spi, struct spi_transfer *xfer)
{
	struct dw_spi *dws = spi_controller_get_devdata(host);
	enum dma_slave_buswidth dma_bus_width;

	if (xfer->len <= dws->fifo_len)
		return false;

	dma_bus_width = dw_spi_dma_convert_width(dws->n_bytes);

	return dws->dma_addr_widths & BIT(dma_bus_width);
}

static int dw_spi_dma_wait(struct dw_spi *dws, unsigned int len, u32 speed)
{
	unsigned long long ms;

	ms = len * MSEC_PER_SEC * BITS_PER_BYTE;
	do_div(ms, speed);
	ms += ms + 200;

	if (ms > UINT_MAX)
		ms = UINT_MAX;

	ms = wait_for_completion_timeout(&dws->dma_completion,
					 msecs_to_jiffies(ms));

	if (ms == 0) {
		dev_err(&dws->host->cur_msg->spi->dev,
			"DMA transaction timed out\n");
		return -ETIMEDOUT;
	}

	return 0;
}

static inline bool dw_spi_dma_tx_busy(struct dw_spi *dws)
{
	return !(dw_readl(dws, DW_SPI_SR) & DW_SPI_SR_TF_EMPT);
}

static int dw_spi_dma_wait_tx_done(struct dw_spi *dws,
				   struct spi_transfer *xfer)
{
	int retry = DW_SPI_WAIT_RETRIES;
	struct spi_delay delay;
	u32 nents;

	nents = dw_readl(dws, DW_SPI_TXFLR);
	delay.unit = SPI_DELAY_UNIT_SCK;
	delay.value = nents * dws->n_bytes * BITS_PER_BYTE;

	while (dw_spi_dma_tx_busy(dws) && retry--)
		spi_delay_exec(&delay, xfer);

	if (retry < 0) {
		dev_err(&dws->host->dev, "Tx hanged up\n");
		return -EIO;
	}

	return 0;
}

/*
 * dws->dma_chan_busy is set before the dma transfer starts, callback for tx
 * channel will clear a corresponding bit.
 */
static void dw_spi_dma_tx_done(void *arg)
{
	struct dw_spi *dws = arg;

	clear_bit(DW_SPI_TX_BUSY, &dws->dma_chan_busy);
	if (test_bit(DW_SPI_RX_BUSY, &dws->dma_chan_busy))
		return;

	complete(&dws->dma_completion);
}

static int dw_spi_dma_config_tx(struct dw_spi *dws)
{
	struct dma_slave_config txconf;

	memset(&txconf, 0, sizeof(txconf));
	txconf.direction = DMA_MEM_TO_DEV;
	txconf.dst_addr = dws->dma_addr;
	txconf.dst_maxburst = dws->txburst;
	txconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
	txconf.dst_addr_width = dw_spi_dma_convert_width(dws->n_bytes);
	txconf.device_fc = false;

	return dmaengine_slave_config(dws->txchan, &txconf);
}

static int dw_spi_dma_submit_tx(struct dw_spi *dws, struct scatterlist *sgl,
				unsigned int nents)
{
	struct dma_async_tx_descriptor *txdesc;
	dma_cookie_t cookie;
	int ret;

	txdesc = dmaengine_prep_slave_sg(dws->txchan, sgl, nents,
					 DMA_MEM_TO_DEV,
					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
	if (!txdesc)
		return -ENOMEM;

	txdesc->callback = dw_spi_dma_tx_done;
	txdesc->callback_param = dws;

	cookie = dmaengine_submit(txdesc);
	ret = dma_submit_error(cookie);
	if (ret) {
		dmaengine_terminate_sync(dws->txchan);
		return ret;
	}

	set_bit(DW_SPI_TX_BUSY, &dws->dma_chan_busy);

	return 0;
}

static inline bool dw_spi_dma_rx_busy(struct dw_spi *dws)
{
	return !!(dw_readl(dws, DW_SPI_SR) & DW_SPI_SR_RF_NOT_EMPT);
}

static int dw_spi_dma_wait_rx_done(struct dw_spi *dws)
{
	int retry = DW_SPI_WAIT_RETRIES;
	struct spi_delay delay;
	unsigned long ns, us;
	u32 nents;

	/*
	 * It's unlikely that DMA engine is still doing the data fetching, but
	 * if it's let's give it some reasonable time. The timeout calculation
	 * is based on the synchronous APB/SSI reference clock rate, on a
	 * number of data entries left in the Rx FIFO, times a number of clock
	 * periods normally needed for a single APB read/write transaction
	 * without PREADY signal utilized (which is true for the DW APB SSI
	 * controller).
	 */
	nents = dw_readl(dws, DW_SPI_RXFLR);
	ns = 4U * NSEC_PER_SEC / dws->max_freq * nents;
	if (ns <= NSEC_PER_USEC) {
		delay.unit = SPI_DELAY_UNIT_NSECS;
		delay.value = ns;
	} else {
		us = DIV_ROUND_UP(ns, NSEC_PER_USEC);
		delay.unit = SPI_DELAY_UNIT_USECS;
		delay.value = clamp_val(us, 0, USHRT_MAX);
	}

	while (dw_spi_dma_rx_busy(dws) && retry--)
		spi_delay_exec(&delay, NULL);

	if (retry < 0) {
		dev_err(&dws->host->dev, "Rx hanged up\n");
		return -EIO;
	}

	return 0;
}

/*
 * dws->dma_chan_busy is set before the dma transfer starts, callback for rx
 * channel will clear a corresponding bit.
 */
static void dw_spi_dma_rx_done(void *arg)
{
	struct dw_spi *dws = arg;

	clear_bit(DW_SPI_RX_BUSY, &dws->dma_chan_busy);
	if (test_bit(DW_SPI_TX_BUSY, &dws->dma_chan_busy))
		return;

	complete(&dws->dma_completion);
}

static int dw_spi_dma_config_rx(struct dw_spi *dws)
{
	struct dma_slave_config rxconf;

	memset(&rxconf, 0, sizeof(rxconf));
	rxconf.direction = DMA_DEV_TO_MEM;
	rxconf.src_addr = dws->dma_addr;
	rxconf.src_maxburst = dws->rxburst;
	rxconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
	rxconf.src_addr_width = dw_spi_dma_convert_width(dws->n_bytes);
	rxconf.device_fc = false;

	return dmaengine_slave_config(dws->rxchan, &rxconf);
}

static int dw_spi_dma_submit_rx(struct dw_spi *dws, struct scatterlist *sgl,
				unsigned int nents)
{
	struct dma_async_tx_descriptor *rxdesc;
	dma_cookie_t cookie;
	int ret;

	rxdesc = dmaengine_prep_slave_sg(dws->rxchan, sgl, nents,
					 DMA_DEV_TO_MEM,
					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
	if (!rxdesc)
		return -ENOMEM;

	rxdesc->callback = dw_spi_dma_rx_done;
	rxdesc->callback_param = dws;

	cookie = dmaengine_submit(rxdesc);
	ret = dma_submit_error(cookie);
	if (ret) {
		dmaengine_terminate_sync(dws->rxchan);
		return ret;
	}

	set_bit(DW_SPI_RX_BUSY, &dws->dma_chan_busy);

	return 0;
}

static int dw_spi_dma_setup(struct dw_spi *dws, struct spi_transfer *xfer)
{
	u16 imr, dma_ctrl;
	int ret;

	if (!xfer->tx_buf)
		return -EINVAL;

	/* Setup DMA channels */
	ret = dw_spi_dma_config_tx(dws);
	if (ret)
		return ret;

	if (xfer->rx_buf) {
		ret = dw_spi_dma_config_rx(dws);
		if (ret)
			return ret;
	}

	/* Set the DMA handshaking interface */
	dma_ctrl = DW_SPI_DMACR_TDMAE;
	if (xfer->rx_buf)
		dma_ctrl |= DW_SPI_DMACR_RDMAE;
	dw_writel(dws, DW_SPI_DMACR, dma_ctrl);

	/* Set the interrupt mask */
	imr = DW_SPI_INT_TXOI;
	if (xfer->rx_buf)
		imr |= DW_SPI_INT_RXUI | DW_SPI_INT_RXOI;
	dw_spi_umask_intr(dws, imr);

	reinit_completion(&dws->dma_completion);

	dws->transfer_handler = dw_spi_dma_transfer_handler;

	return 0;
}

static int dw_spi_dma_transfer_all(struct dw_spi *dws,
				   struct spi_transfer *xfer)
{
	int ret;

	/* Submit the DMA Tx transfer */
	ret = dw_spi_dma_submit_tx(dws, xfer->tx_sg.sgl, xfer->tx_sg.nents);
	if (ret)
		goto err_clear_dmac;

	/* Submit the DMA Rx transfer if required */
	if (xfer->rx_buf) {
		ret = dw_spi_dma_submit_rx(dws, xfer->rx_sg.sgl,
					   xfer->rx_sg.nents);
		if (ret)
			goto err_clear_dmac;

		/* rx must be started before tx due to spi instinct */
		dma_async_issue_pending(dws->rxchan);
	}

	dma_async_issue_pending(dws->txchan);

	ret = dw_spi_dma_wait(dws, xfer->len, xfer->effective_speed_hz);

err_clear_dmac:
	dw_writel(dws, DW_SPI_DMACR, 0);

	return ret;
}

/*
 * In case if at least one of the requested DMA channels doesn't support the
 * hardware accelerated SG list entries traverse, the DMA driver will most
 * likely work that around by performing the IRQ-based SG list entries
 * resubmission. That might and will cause a problem if the DMA Tx channel is
 * recharged and re-executed before the Rx DMA channel. Due to
 * non-deterministic IRQ-handler execution latency the DMA Tx channel will
 * start pushing data to the SPI bus before the Rx DMA channel is even
 * reinitialized with the next inbound SG list entry. By doing so the DMA Tx
 * channel will implicitly start filling the DW APB SSI Rx FIFO up, which while
 * the DMA Rx channel being recharged and re-executed will eventually be
 * overflown.
 *
 * In order to solve the problem we have to feed the DMA engine with SG list
 * entries one-by-one. It shall keep the DW APB SSI Tx and Rx FIFOs
 * synchronized and prevent the Rx FIFO overflow. Since in general the tx_sg
 * and rx_sg lists may have different number of entries of different lengths
 * (though total length should match) let's virtually split the SG-lists to the
 * set of DMA transfers, which length is a minimum of the ordered SG-entries
 * lengths. An ASCII-sketch of the implemented algo is following:
 *                  xfer->len
 *                |___________|
 * tx_sg list:    |___|____|__|
 * rx_sg list:    |_|____|____|
 * DMA transfers: |_|_|__|_|__|
 *
 * Note in order to have this workaround solving the denoted problem the DMA
 * engine driver should properly initialize the max_sg_burst capability and set
 * the DMA device max segment size parameter with maximum data block size the
 * DMA engine supports.
 */

static int dw_spi_dma_transfer_one(struct dw_spi *dws,
				   struct spi_transfer *xfer)
{
	struct scatterlist *tx_sg = NULL, *rx_sg = NULL, tx_tmp, rx_tmp;
	unsigned int tx_len = 0, rx_len = 0;
	unsigned int base, len;
	int ret;

	sg_init_table(&tx_tmp, 1);
	sg_init_table(&rx_tmp, 1);

	for (base = 0; base < xfer->len; base += len) {
		/* Fetch next Tx DMA data chunk */
		if (!tx_len) {
			tx_sg = !tx_sg ? &xfer->tx_sg.sgl[0] : sg_next(tx_sg);
			sg_dma_address(&tx_tmp) = sg_dma_address(tx_sg);
			tx_len = sg_dma_len(tx_sg);
		}

		/* Fetch next Rx DMA data chunk */
		if (!rx_len) {
			rx_sg = !rx_sg ? &xfer->rx_sg.sgl[0] : sg_next(rx_sg);
			sg_dma_address(&rx_tmp) = sg_dma_address(rx_sg);
			rx_len = sg_dma_len(rx_sg);
		}

		len = min(tx_len, rx_len);

		sg_dma_len(&tx_tmp) = len;
		sg_dma_len(&rx_tmp) = len;

		/* Submit DMA Tx transfer */
		ret = dw_spi_dma_submit_tx(dws, &tx_tmp, 1);
		if (ret)
			break;

		/* Submit DMA Rx transfer */
		ret = dw_spi_dma_submit_rx(dws, &rx_tmp, 1);
		if (ret)
			break;

		/* Rx must be started before Tx due to SPI instinct */
		dma_async_issue_pending(dws->rxchan);

		dma_async_issue_pending(dws->txchan);

		/*
		 * Here we only need to wait for the DMA transfer to be
		 * finished since SPI controller is kept enabled during the
		 * procedure this loop implements and there is no risk to lose
		 * data left in the Tx/Rx FIFOs.
		 */
		ret = dw_spi_dma_wait(dws, len, xfer->effective_speed_hz);
		if (ret)
			break;

		reinit_completion(&dws->dma_completion);

		sg_dma_address(&tx_tmp) += len;
		sg_dma_address(&rx_tmp) += len;
		tx_len -= len;
		rx_len -= len;
	}

	dw_writel(dws, DW_SPI_DMACR, 0);

	return ret;
}

static int dw_spi_dma_transfer(struct dw_spi *dws, struct spi_transfer *xfer)
{
	unsigned int nents;
	int ret;

	nents = max(xfer->tx_sg.nents, xfer->rx_sg.nents);

	/*
	 * Execute normal DMA-based transfer (which submits the Rx and Tx SG
	 * lists directly to the DMA engine at once) if either full hardware
	 * accelerated SG list traverse is supported by both channels, or the
	 * Tx-only SPI transfer is requested, or the DMA engine is capable to
	 * handle both SG lists on hardware accelerated basis.
	 */
	if (!dws->dma_sg_burst || !xfer->rx_buf || nents <= dws->dma_sg_burst)
		ret = dw_spi_dma_transfer_all(dws, xfer);
	else
		ret = dw_spi_dma_transfer_one(dws, xfer);
	if (ret)
		return ret;

	if (dws->host->cur_msg->status == -EINPROGRESS) {
		ret = dw_spi_dma_wait_tx_done(dws, xfer);
		if (ret)
			return ret;
	}

	if (xfer->rx_buf && dws->host->cur_msg->status == -EINPROGRESS)
		ret = dw_spi_dma_wait_rx_done(dws);

	return ret;
}

static void dw_spi_dma_stop(struct dw_spi *dws)
{
	if (test_bit(DW_SPI_TX_BUSY, &dws->dma_chan_busy)) {
		dmaengine_terminate_sync(dws->txchan);
		clear_bit(DW_SPI_TX_BUSY, &dws->dma_chan_busy);
	}
	if (test_bit(DW_SPI_RX_BUSY, &dws->dma_chan_busy)) {
		dmaengine_terminate_sync(dws->rxchan);
		clear_bit(DW_SPI_RX_BUSY, &dws->dma_chan_busy);
	}
}

static const struct dw_spi_dma_ops dw_spi_dma_mfld_ops = {
	.dma_init	= dw_spi_dma_init_mfld,
	.dma_exit	= dw_spi_dma_exit,
	.dma_setup	= dw_spi_dma_setup,
	.can_dma	= dw_spi_can_dma,
	.dma_transfer	= dw_spi_dma_transfer,
	.dma_stop	= dw_spi_dma_stop,
};

void dw_spi_dma_setup_mfld(struct dw_spi *dws)
{
	dws->dma_ops = &dw_spi_dma_mfld_ops;
}
EXPORT_SYMBOL_NS_GPL(dw_spi_dma_setup_mfld, "SPI_DW_CORE");

static const struct dw_spi_dma_ops dw_spi_dma_generic_ops = {
	.dma_init	= dw_spi_dma_init_generic,
	.dma_exit	= dw_spi_dma_exit,
	.dma_setup	= dw_spi_dma_setup,
	.can_dma	= dw_spi_can_dma,
	.dma_transfer	= dw_spi_dma_transfer,
	.dma_stop	= dw_spi_dma_stop,
};

void dw_spi_dma_setup_generic(struct dw_spi *dws)
{
	dws->dma_ops = &dw_spi_dma_generic_ops;
}
EXPORT_SYMBOL_NS_GPL(dw_spi_dma_setup_generic, "SPI_DW_CORE");