#
# QCOM Soc drivers
#
menu "Qualcomm SoC drivers"

config QCOM_COMMAND_DB
	bool "Qualcomm Command DB"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on OF_RESERVED_MEM
	help
	  Command DB queries shared memory by key string for shared system
	  resources. Platform drivers that require to set state of a shared
	  resource on a RPM-hardened platform must use this database to get
	  SoC specific identifier and information for the shared resources.

config QCOM_GENI_SE
	tristate "QCOM GENI Serial Engine Driver"
	depends on ARCH_QCOM || COMPILE_TEST
	help
	  This driver is used to manage Generic Interface (GENI) firmware based
	  Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper. This
	  driver is also used to manage the common aspects of multiple Serial
	  Engines present in the QUP.

config QCOM_GLINK_SSR
	tristate "Qualcomm Glink SSR driver"
	depends on RPMSG
	depends on QCOM_RPROC_COMMON
	help
	  Say y here to enable GLINK SSR support. The GLINK SSR driver
	  implements the SSR protocol for notifying the remote processor about
	  neighboring subsystems going up or down.

config QCOM_GSBI
        tristate "QCOM General Serial Bus Interface"
        depends on ARCH_QCOM || COMPILE_TEST
        select MFD_SYSCON
        help
          Say y here to enable GSBI support.  The GSBI provides control
          functions for connecting the underlying serial UART, SPI, and I2C
          devices to the output pins.

config QCOM_LLCC
	tristate "Qualcomm Technologies, Inc. LLCC driver"
	depends on ARCH_QCOM || COMPILE_TEST
	help
	  Qualcomm Technologies, Inc. platform specific
	  Last Level Cache Controller(LLCC) driver. This provides interfaces
	  to clients that use the LLCC. Say yes here to enable LLCC slice
	  driver.

config QCOM_SDM845_LLCC
	tristate "Qualcomm Technologies, Inc. SDM845 LLCC driver"
	depends on QCOM_LLCC
	help
	  Say yes here to enable the LLCC driver for SDM845. This provides
	  data required to configure LLCC so that clients can start using the
	  LLCC slices.

config QCOM_MDT_LOADER
	tristate
	select QCOM_SCM

config QCOM_PM
	bool "Qualcomm Power Management"
	depends on ARCH_QCOM && !ARM64
	select ARM_CPU_SUSPEND
	select QCOM_SCM
	help
	  QCOM Platform specific power driver to manage cores and L2 low power
	  modes. It interface with various system drivers to put the cores in
	  low power modes.

config QCOM_QMI_HELPERS
	tristate
	depends on ARCH_QCOM || COMPILE_TEST
	depends on NET
	help
	  Helper library for handling QMI encoded messages.  QMI encoded
	  messages are used in communication between the majority of QRTR
	  clients and this helpers provide the common functionality needed for
	  doing this from a kernel driver.

config QCOM_RMTFS_MEM
	tristate "Qualcomm Remote Filesystem memory driver"
	depends on ARCH_QCOM
	select QCOM_SCM
	help
	  The Qualcomm remote filesystem memory driver is used for allocating
	  and exposing regions of shared memory with remote processors for the
	  purpose of exchanging sector-data between the remote filesystem
	  service and its clients.

	  Say y here if you intend to boot the modem remoteproc.

config QCOM_RPMH
	bool "Qualcomm RPM-Hardened (RPMH) Communication"
	depends on ARCH_QCOM && ARM64 || COMPILE_TEST
	help
	  Support for communication with the hardened-RPM blocks in
	  Qualcomm Technologies Inc (QTI) SoCs. RPMH communication uses an
	  internal bus to transmit state requests for shared resources. A set
	  of hardware components aggregate requests for these resources and
	  help apply the aggregated state on the resource.

config QCOM_SMEM
	tristate "Qualcomm Shared Memory Manager (SMEM)"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on HWSPINLOCK
	help
	  Say y here to enable support for the Qualcomm Shared Memory Manager.
	  The driver provides an interface to items in a heap shared among all
	  processors in a Qualcomm platform.

config QCOM_SMD_RPM
	tristate "Qualcomm Resource Power Manager (RPM) over SMD"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on RPMSG
	help
	  If you say yes to this option, support will be included for the
	  Resource Power Manager system found in the Qualcomm 8974 based
	  devices.

	  This is required to access many regulators, clocks and bus
	  frequencies controlled by the RPM on these devices.

	  Say M here if you want to include support for the Qualcomm RPM as a
	  module. This will build a module called "qcom-smd-rpm".

config QCOM_SMEM_STATE
	bool

config QCOM_SMP2P
	tristate "Qualcomm Shared Memory Point to Point support"
	depends on MAILBOX
	depends on QCOM_SMEM
	select QCOM_SMEM_STATE
	select IRQ_DOMAIN
	help
	  Say yes here to support the Qualcomm Shared Memory Point to Point
	  protocol.

config QCOM_SMSM
	tristate "Qualcomm Shared Memory State Machine"
	depends on QCOM_SMEM
	select QCOM_SMEM_STATE
	select IRQ_DOMAIN
	help
	  Say yes here to support the Qualcomm Shared Memory State Machine.
	  The state machine is represented by bits in shared memory.

config QCOM_WCNSS_CTRL
	tristate "Qualcomm WCNSS control driver"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on RPMSG
	help
	  Client driver for the WCNSS_CTRL SMD channel, used to download nv
	  firmware to a newly booted WCNSS chip.

config QCOM_APR
	tristate "Qualcomm APR Bus (Asynchronous Packet Router)"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on RPMSG
	help
          Enable APR IPC protocol support between
          application processor and QDSP6. APR is
          used by audio driver to configure QDSP6
          ASM, ADM and AFE modules.
endmenu