| /* | |
| * Copyright (c) 2020-2021, Arm Limited. All rights reserved. | |
| * | |
| * SPDX-License-Identifier: BSD-3-Clause | |
| */ | |
| /dts-v1/; | |
| / { | |
| compatible = "arm,tc"; | |
| interrupt-parent = <&gic>; | |
| #address-cells = <2>; | |
| #size-cells = <2>; | |
| aliases { | |
| serial0 = &soc_uart0; | |
| }; | |
| chosen { | |
| bootargs = "console=ttyAMA0 debug user_debug=31 earlycon=pl011,0x7ff80000 loglevel=9 androidboot.hardware=total_compute androidboot.boot_devices=1c050000.mmci ip=dhcp androidboot.selinux=permissive allow_mismatched_32bit_el0"; | |
| stdout-path = "serial0:115200n8"; | |
| }; | |
| cpus { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| cpu-map { | |
| cluster0 { | |
| core0 { | |
| cpu = <&CPU0>; | |
| }; | |
| core1 { | |
| cpu = <&CPU1>; | |
| }; | |
| core2 { | |
| cpu = <&CPU2>; | |
| }; | |
| core3 { | |
| cpu = <&CPU3>; | |
| }; | |
| core4 { | |
| cpu = <&CPU4>; | |
| }; | |
| core5 { | |
| cpu = <&CPU5>; | |
| }; | |
| core6 { | |
| cpu = <&CPU6>; | |
| }; | |
| core7 { | |
| cpu = <&CPU7>; | |
| }; | |
| }; | |
| }; | |
| /* | |
| * The timings below are just to demonstrate working cpuidle. | |
| * These values may be inaccurate. | |
| */ | |
| idle-states { | |
| entry-method = "arm,psci"; | |
| CPU_SLEEP_0: cpu-sleep-0 { | |
| compatible = "arm,idle-state"; | |
| arm,psci-suspend-param = <0x0010000>; | |
| local-timer-stop; | |
| entry-latency-us = <300>; | |
| exit-latency-us = <1200>; | |
| min-residency-us = <2000>; | |
| }; | |
| CLUSTER_SLEEP_0: cluster-sleep-0 { | |
| compatible = "arm,idle-state"; | |
| arm,psci-suspend-param = <0x1010000>; | |
| local-timer-stop; | |
| entry-latency-us = <400>; | |
| exit-latency-us = <1200>; | |
| min-residency-us = <2500>; | |
| }; | |
| }; | |
| amus { | |
| amu: amu-0 { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| mpmm_gear0: counter@0 { | |
| reg = <0>; | |
| enable-at-el3; | |
| }; | |
| mpmm_gear1: counter@1 { | |
| reg = <1>; | |
| enable-at-el3; | |
| }; | |
| mpmm_gear2: counter@2 { | |
| reg = <2>; | |
| enable-at-el3; | |
| }; | |
| }; | |
| }; | |
| CPU0:cpu@0 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x0>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 0>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <406>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU1:cpu@100 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x100>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 0>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <406>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU2:cpu@200 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x200>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 0>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <406>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU3:cpu@300 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x300>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 0>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <406>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU4:cpu@400 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x400>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 1>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <912>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU5:cpu@500 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x500>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 1>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <912>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU6:cpu@600 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x600>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 1>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <912>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| CPU7:cpu@700 { | |
| device_type = "cpu"; | |
| compatible = "arm,armv8"; | |
| reg = <0x700>; | |
| enable-method = "psci"; | |
| clocks = <&scmi_dvfs 2>; | |
| cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; | |
| capacity-dmips-mhz = <1024>; | |
| amu = <&amu>; | |
| supports-mpmm; | |
| }; | |
| }; | |
| reserved-memory { | |
| #address-cells = <2>; | |
| #size-cells = <2>; | |
| ranges; | |
| optee@0xfce00000 { | |
| reg = <0x00000000 0xfce00000 0 0x00200000>; | |
| no-map; | |
| }; | |
| }; | |
| psci { | |
| compatible = "arm,psci-1.0", "arm,psci-0.2"; | |
| method = "smc"; | |
| }; | |
| sram: sram@6000000 { | |
| compatible = "mmio-sram"; | |
| reg = <0x0 0x06000000 0x0 0x8000>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0 0x0 0x06000000 0x8000>; | |
| cpu_scp_scmi_mem: scp-shmem@0 { | |
| compatible = "arm,scmi-shmem"; | |
| reg = <0x0 0x80>; | |
| }; | |
| }; | |
| mbox_db_rx: mhu@45010000 { | |
| compatible = "arm,mhuv2-rx","arm,primecell"; | |
| reg = <0x0 0x45010000 0x0 0x1000>; | |
| clocks = <&soc_refclk100mhz>; | |
| clock-names = "apb_pclk"; | |
| #mbox-cells = <2>; | |
| interrupts = <0 317 4>; | |
| interrupt-names = "mhu_rx"; | |
| mhu-protocol = "doorbell"; | |
| arm,mhuv2-protocols = <0 1>; | |
| }; | |
| mbox_db_tx: mhu@45000000 { | |
| compatible = "arm,mhuv2-tx","arm,primecell"; | |
| reg = <0x0 0x45000000 0x0 0x1000>; | |
| clocks = <&soc_refclk100mhz>; | |
| clock-names = "apb_pclk"; | |
| #mbox-cells = <2>; | |
| interrupt-names = "mhu_tx"; | |
| mhu-protocol = "doorbell"; | |
| arm,mhuv2-protocols = <0 1>; | |
| }; | |
| scmi { | |
| compatible = "arm,scmi"; | |
| mbox-names = "tx", "rx"; | |
| mboxes = <&mbox_db_tx 0 0 &mbox_db_rx 0 0 >; | |
| shmem = <&cpu_scp_scmi_mem &cpu_scp_scmi_mem>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| scmi_dvfs: protocol@13 { | |
| reg = <0x13>; | |
| #clock-cells = <1>; | |
| }; | |
| scmi_clk: protocol@14 { | |
| reg = <0x14>; | |
| #clock-cells = <1>; | |
| }; | |
| }; | |
| gic: interrupt-controller@2c010000 { | |
| compatible = "arm,gic-600", "arm,gic-v3"; | |
| #address-cells = <2>; | |
| #interrupt-cells = <3>; | |
| #size-cells = <2>; | |
| ranges; | |
| interrupt-controller; | |
| reg = <0x0 0x30000000 0 0x10000>, /* GICD */ | |
| <0x0 0x30080000 0 0x200000>; /* GICR */ | |
| interrupts = <0x1 0x9 0x4>; | |
| }; | |
| timer { | |
| compatible = "arm,armv8-timer"; | |
| interrupts = <0x1 13 0x8>, | |
| <0x1 14 0x8>, | |
| <0x1 11 0x8>, | |
| <0x1 10 0x8>; | |
| }; | |
| soc_refclk100mhz: refclk100mhz { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <100000000>; | |
| clock-output-names = "apb_pclk"; | |
| }; | |
| soc_refclk60mhz: refclk60mhz { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <60000000>; | |
| clock-output-names = "iofpga_clk"; | |
| }; | |
| soc_uartclk: uartclk { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <50000000>; | |
| clock-output-names = "uartclk"; | |
| }; | |
| soc_uart0: uart@7ff80000 { | |
| compatible = "arm,pl011", "arm,primecell"; | |
| reg = <0x0 0x7ff80000 0x0 0x1000>; | |
| interrupts = <0x0 116 0x4>; | |
| clocks = <&soc_uartclk>, <&soc_refclk100mhz>; | |
| clock-names = "uartclk", "apb_pclk"; | |
| status = "okay"; | |
| }; | |
| vencoder { | |
| compatible = "drm,virtual-encoder"; | |
| port { | |
| vencoder_in: endpoint { | |
| remote-endpoint = <&dp_pl0_out0>; | |
| }; | |
| }; | |
| display-timings { | |
| panel-timing { | |
| clock-frequency = <25175000>; | |
| hactive = <640>; | |
| vactive = <480>; | |
| hfront-porch = <16>; | |
| hback-porch = <48>; | |
| hsync-len = <96>; | |
| vfront-porch = <10>; | |
| vback-porch = <33>; | |
| vsync-len = <2>; | |
| }; | |
| }; | |
| }; | |
| hdlcd: hdlcd@7ff60000 { | |
| compatible = "arm,hdlcd"; | |
| reg = <0x0 0x7ff60000 0x0 0x1000>; | |
| interrupts = <0x0 117 0x4>; | |
| clocks = <&fake_hdlcd_clk>; | |
| clock-names = "pxlclk"; | |
| status = "disabled"; | |
| port { | |
| hdlcd_out: endpoint { | |
| remote-endpoint = <&vencoder_in>; | |
| }; | |
| }; | |
| }; | |
| fake_hdlcd_clk: fake-hdlcd-clk { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <25175000>; | |
| clock-output-names = "pxlclk"; | |
| }; | |
| ethernet@18000000 { | |
| compatible = "smsc,lan91c111"; | |
| reg = <0x0 0x18000000 0x0 0x10000>; | |
| interrupts = <0 109 4>; | |
| }; | |
| kmi@1c060000 { | |
| compatible = "arm,pl050", "arm,primecell"; | |
| reg = <0x0 0x001c060000 0x0 0x1000>; | |
| interrupts = <0 197 4>; | |
| clocks = <&bp_clock24mhz>, <&bp_clock24mhz>; | |
| clock-names = "KMIREFCLK", "apb_pclk"; | |
| }; | |
| kmi@1c070000 { | |
| compatible = "arm,pl050", "arm,primecell"; | |
| reg = <0x0 0x001c070000 0x0 0x1000>; | |
| interrupts = <0 103 4>; | |
| clocks = <&bp_clock24mhz>, <&bp_clock24mhz>; | |
| clock-names = "KMIREFCLK", "apb_pclk"; | |
| }; | |
| bp_clock24mhz: clock24mhz { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <24000000>; | |
| clock-output-names = "bp:clock24mhz"; | |
| }; | |
| virtio_block@1c130000 { | |
| compatible = "virtio,mmio"; | |
| reg = <0x0 0x1c130000 0x0 0x200>; | |
| interrupts = <0 204 4>; | |
| }; | |
| sysreg: sysreg@1c010000 { | |
| compatible = "arm,vexpress-sysreg"; | |
| reg = <0x0 0x001c010000 0x0 0x1000>; | |
| gpio-controller; | |
| #gpio-cells = <2>; | |
| }; | |
| fixed_3v3: v2m-3v3 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "3V3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| regulator-always-on; | |
| }; | |
| mmci@1c050000 { | |
| compatible = "arm,pl180", "arm,primecell"; | |
| reg = <0x0 0x001c050000 0x0 0x1000>; | |
| interrupts = <0 107 0x4>, | |
| <0 108 0x4>; | |
| cd-gpios = <&sysreg 0 0>; | |
| wp-gpios = <&sysreg 1 0>; | |
| bus-width = <8>; | |
| max-frequency = <12000000>; | |
| vmmc-supply = <&fixed_3v3>; | |
| clocks = <&bp_clock24mhz>, <&bp_clock24mhz>; | |
| clock-names = "mclk", "apb_pclk"; | |
| }; | |
| dp0: display@2cc00000 { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| compatible = "arm,mali-d71"; | |
| reg = <0 0x2cc00000 0 0x20000>; | |
| interrupts = <0 69 4>; | |
| interrupt-names = "DPU"; | |
| clocks = <&scmi_clk 0>; | |
| clock-names = "aclk"; | |
| pl0: pipeline@0 { | |
| reg = <0>; | |
| clocks = <&scmi_clk 1>; | |
| clock-names = "pxclk"; | |
| pl_id = <0>; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| dp_pl0_out0: endpoint { | |
| remote-endpoint = <&vencoder_in>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| pl1: pipeline@1 { | |
| reg = <1>; | |
| clocks = <&scmi_clk 2>; | |
| clock-names = "pxclk"; | |
| pl_id = <1>; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; |