blob: 1a04e4457258ebe6b6903bec17a429daf420a55c [file] [log] [blame]
****************************
Technexion i.MX8M Pico board
****************************
This file documents the Buildroot support for the Technexion i.MX8M
Pico board. The Pico i.MX8M system-on-module [1] is present in
development kits like the Pico Pi i.MX8M [2].
Build
=====
First, configure Buildroot for the i.MX8M Pico board:
make imx8mpico_defconfig
Build all components:
make
You will find in output/images/ the following files:
- bl31.bin
- boot.vfat
- Image
- imx8-boot-sd.bin
- lpddr4_pmu_train_fw.bin
- pico-8m-dcss-ili9881c.dtb
- pico-8m.dtb
- rootfs.ext4
- sdcard.img
- signed_hdmi_imx8m.bin
- u-boot.imx
Flashing sdcard.img on the eMMC
===============================
i.MX8M Pico board does not have a SD card slot. The storage is an
eMMC. An easy way to flash the eMMC is to use the u-boot ums
command. The boards are sold pre-flashed with such a u-boot. It is
assumed here that the board has already a working u-boot on eMMC and
jumpers are set to boot on eMMC. See [3].
Jumper configuration for eMMC boot:
J1: jumper on pins 4 and 6.
J2: jumper on pins 2 and 4.
In case the board was flashed with a wrong u-boot, or the eMMC is
erased, u-boot can be loaded by USB Serial Download boot mode, using
imx-usb-loader. See [3] and [4].
For flashing:
- Plug the micro USB cable from the Debug USB Port, to your computer
- Plug the USB Type C to your computer, this will power up the board
In the U-Boot prompt launch:
=> ums 0 mmc 0
This will mount the eMMC content in the host PC as a mass storage device.
To determine the device associated to the eMMC card have a look in the
/proc/partitions file:
cat /proc/partitions
If your system automatically mount some device partitions, make sure
to unmount them.
Buildroot prepares a bootable "sdcard.img" image in the output/images/
directory, ready to be dumped on the eMMC. Launch the following
command as root:
dd if=output/images/sdcard.img of=/dev/<your-sd-device>
*** WARNING! This will destroy all the eMMC content. Use with care! ***
This operation can take several minutes, depending on the image
size. When tested, a 2MB/s transfer rate was observed.
For details about the medium image layout, see the definition in
board/freescale/common/imx/genimage.cfg.template.
Boot the i.MX8M Pico board
==========================
To boot your newly created system:
- put a micro USB cable into the Debug USB Port and connect using a terminal
emulator at 115200 bps, 8n1;
- power on the board, with USB Type C connector.
Enjoy!
[1]. https://www.technexion.com/products/system-on-modules/pico/pico-compute-modules/detail/PICO-IMX8M
[2]. https://www.technexion.com/products/system-on-modules/pico-evaluation-kits/detail/PICO-PI-IMX8M-BASIC
[3]. https://www.technexion.com/support/knowledgebase/boot-configuration-settings-for-pico-baseboards/
[4]. https://www.technexion.com/support/knowledgebase/loading-bootable-software-images-onto-the-emmc-of-picosom-on-pico-pi/