| // SPDX-License-Identifier: GPL-2.0 |
| #include "bcm283x.dtsi" |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/soc/bcm2835-pm.h> |
| |
| / { |
| compatible = "brcm,bcm2711"; |
| |
| #address-cells = <2>; |
| #size-cells = <1>; |
| |
| interrupt-parent = <&gicv2>; |
| |
| vc4: gpu { |
| compatible = "brcm,bcm2711-vc5"; |
| status = "disabled"; |
| }; |
| |
| clk_27MHz: clk-27M { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <27000000>; |
| clock-output-names = "27MHz-clock"; |
| }; |
| |
| clk_108MHz: clk-108M { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <108000000>; |
| clock-output-names = "108MHz-clock"; |
| }; |
| |
| soc { |
| /* |
| * Defined ranges: |
| * Common BCM283x peripherals |
| * BCM2711-specific peripherals |
| * ARM-local peripherals |
| */ |
| ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, |
| <0x7c000000 0x0 0xfc000000 0x02000000>, |
| <0x40000000 0x0 0xff800000 0x00800000>; |
| /* Emulate a contiguous 30-bit address range for DMA */ |
| dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; |
| |
| /* |
| * This node is the provider for the enable-method for |
| * bringing up secondary cores. |
| */ |
| local_intc: local_intc@40000000 { |
| compatible = "brcm,bcm2836-l1-intc"; |
| reg = <0x40000000 0x100>; |
| }; |
| |
| gicv2: interrupt-controller@40041000 { |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| compatible = "arm,gic-400"; |
| reg = <0x40041000 0x1000>, |
| <0x40042000 0x2000>, |
| <0x40044000 0x2000>, |
| <0x40046000 0x2000>; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| avs_monitor: avs-monitor@7d5d2000 { |
| compatible = "brcm,bcm2711-avs-monitor", |
| "syscon", "simple-mfd"; |
| reg = <0x7d5d2000 0xf00>; |
| |
| thermal: thermal { |
| compatible = "brcm,bcm2711-thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| }; |
| |
| dma: dma@7e007000 { |
| compatible = "brcm,bcm2835-dma"; |
| reg = <0x7e007000 0xb00>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, |
| /* DMA lite 7 - 10 */ |
| <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma0", |
| "dma1", |
| "dma2", |
| "dma3", |
| "dma4", |
| "dma5", |
| "dma6", |
| "dma7", |
| "dma8", |
| "dma9", |
| "dma10"; |
| #dma-cells = <1>; |
| brcm,dma-channel-mask = <0x07f5>; |
| }; |
| |
| pm: watchdog@7e100000 { |
| compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; |
| #power-domain-cells = <1>; |
| #reset-cells = <1>; |
| reg = <0x7e100000 0x114>, |
| <0x7e00a000 0x24>, |
| <0x7ec11000 0x20>; |
| clocks = <&clocks BCM2835_CLOCK_V3D>, |
| <&clocks BCM2835_CLOCK_PERI_IMAGE>, |
| <&clocks BCM2835_CLOCK_H264>, |
| <&clocks BCM2835_CLOCK_ISP>; |
| clock-names = "v3d", "peri_image", "h264", "isp"; |
| system-power-controller; |
| }; |
| |
| rng@7e104000 { |
| compatible = "brcm,bcm2711-rng200"; |
| reg = <0x7e104000 0x28>; |
| }; |
| |
| uart2: serial@7e201400 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x7e201400 0x200>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_UART>, |
| <&clocks BCM2835_CLOCK_VPU>; |
| clock-names = "uartclk", "apb_pclk"; |
| arm,primecell-periphid = <0x00241011>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@7e201600 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x7e201600 0x200>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_UART>, |
| <&clocks BCM2835_CLOCK_VPU>; |
| clock-names = "uartclk", "apb_pclk"; |
| arm,primecell-periphid = <0x00241011>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@7e201800 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x7e201800 0x200>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_UART>, |
| <&clocks BCM2835_CLOCK_VPU>; |
| clock-names = "uartclk", "apb_pclk"; |
| arm,primecell-periphid = <0x00241011>; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@7e201a00 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x7e201a00 0x200>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_UART>, |
| <&clocks BCM2835_CLOCK_VPU>; |
| clock-names = "uartclk", "apb_pclk"; |
| arm,primecell-periphid = <0x00241011>; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@7e204600 { |
| compatible = "brcm,bcm2835-spi"; |
| reg = <0x7e204600 0x0200>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@7e204800 { |
| compatible = "brcm,bcm2835-spi"; |
| reg = <0x7e204800 0x0200>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi5: spi@7e204a00 { |
| compatible = "brcm,bcm2835-spi"; |
| reg = <0x7e204a00 0x0200>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi6: spi@7e204c00 { |
| compatible = "brcm,bcm2835-spi"; |
| reg = <0x7e204c00 0x0200>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@7e205600 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| reg = <0x7e205600 0x200>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@7e205800 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| reg = <0x7e205800 0x200>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@7e205a00 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| reg = <0x7e205a00 0x200>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@7e205c00 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| reg = <0x7e205c00 0x200>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2835_CLOCK_VPU>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| pixelvalve0: pixelvalve@7e206000 { |
| compatible = "brcm,bcm2711-pixelvalve0"; |
| reg = <0x7e206000 0x100>; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| pixelvalve1: pixelvalve@7e207000 { |
| compatible = "brcm,bcm2711-pixelvalve1"; |
| reg = <0x7e207000 0x100>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| pixelvalve2: pixelvalve@7e20a000 { |
| compatible = "brcm,bcm2711-pixelvalve2"; |
| reg = <0x7e20a000 0x100>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| pwm1: pwm@7e20c800 { |
| compatible = "brcm,bcm2835-pwm"; |
| reg = <0x7e20c800 0x28>; |
| clocks = <&clocks BCM2835_CLOCK_PWM>; |
| assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; |
| assigned-clock-rates = <10000000>; |
| #pwm-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| pixelvalve4: pixelvalve@7e216000 { |
| compatible = "brcm,bcm2711-pixelvalve4"; |
| reg = <0x7e216000 0x100>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| hvs: hvs@7e400000 { |
| compatible = "brcm,bcm2711-hvs"; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pixelvalve3: pixelvalve@7ec12000 { |
| compatible = "brcm,bcm2711-pixelvalve3"; |
| reg = <0x7ec12000 0x100>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| dvp: clock@7ef00000 { |
| compatible = "brcm,brcm2711-dvp"; |
| reg = <0x7ef00000 0x10>; |
| clocks = <&clk_108MHz>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| bsc_intr: interrupt-controller@7ef00040 { |
| compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; |
| reg = <0x7ef00040 0x30>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| }; |
| |
| aon_intr: interrupt-controller@7ef00100 { |
| compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; |
| reg = <0x7ef00100 0x30>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| }; |
| |
| hdmi0: hdmi@7ef00700 { |
| compatible = "brcm,bcm2711-hdmi0"; |
| reg = <0x7ef00700 0x300>, |
| <0x7ef00300 0x200>, |
| <0x7ef00f00 0x80>, |
| <0x7ef00f80 0x80>, |
| <0x7ef01b00 0x200>, |
| <0x7ef01f00 0x400>, |
| <0x7ef00200 0x80>, |
| <0x7ef04300 0x100>, |
| <0x7ef20000 0x100>; |
| reg-names = "hdmi", |
| "dvp", |
| "phy", |
| "rm", |
| "packet", |
| "metadata", |
| "csc", |
| "cec", |
| "hd"; |
| clock-names = "hdmi", "bvb", "audio", "cec"; |
| resets = <&dvp 0>; |
| interrupt-parent = <&aon_intr>; |
| interrupts = <0>, <1>, <2>, |
| <3>, <4>, <5>; |
| interrupt-names = "cec-tx", "cec-rx", "cec-low", |
| "wakeup", "hpd-connected", "hpd-removed"; |
| ddc = <&ddc0>; |
| dmas = <&dma 10>; |
| dma-names = "audio-rx"; |
| status = "disabled"; |
| }; |
| |
| ddc0: i2c@7ef04500 { |
| compatible = "brcm,bcm2711-hdmi-i2c"; |
| reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; |
| reg-names = "bsc", "auto-i2c"; |
| clock-frequency = <97500>; |
| interrupt-parent = <&bsc_intr>; |
| interrupts = <0>; |
| status = "disabled"; |
| }; |
| |
| hdmi1: hdmi@7ef05700 { |
| compatible = "brcm,bcm2711-hdmi1"; |
| reg = <0x7ef05700 0x300>, |
| <0x7ef05300 0x200>, |
| <0x7ef05f00 0x80>, |
| <0x7ef05f80 0x80>, |
| <0x7ef06b00 0x200>, |
| <0x7ef06f00 0x400>, |
| <0x7ef00280 0x80>, |
| <0x7ef09300 0x100>, |
| <0x7ef20000 0x100>; |
| reg-names = "hdmi", |
| "dvp", |
| "phy", |
| "rm", |
| "packet", |
| "metadata", |
| "csc", |
| "cec", |
| "hd"; |
| ddc = <&ddc1>; |
| clock-names = "hdmi", "bvb", "audio", "cec"; |
| resets = <&dvp 1>; |
| interrupt-parent = <&aon_intr>; |
| interrupts = <8>, <7>, <6>, |
| <9>, <10>, <11>; |
| interrupt-names = "cec-tx", "cec-rx", "cec-low", |
| "wakeup", "hpd-connected", "hpd-removed"; |
| dmas = <&dma 17>; |
| dma-names = "audio-rx"; |
| status = "disabled"; |
| }; |
| |
| ddc1: i2c@7ef09500 { |
| compatible = "brcm,bcm2711-hdmi-i2c"; |
| reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; |
| reg-names = "bsc", "auto-i2c"; |
| clock-frequency = <97500>; |
| interrupt-parent = <&bsc_intr>; |
| interrupts = <1>; |
| status = "disabled"; |
| }; |
| }; |
| |
| /* |
| * emmc2 has different DMA constraints based on SoC revisions. It was |
| * moved into its own bus, so as for RPi4's firmware to update them. |
| * The firmware will find whether the emmc2bus alias is defined, and if |
| * so, it'll edit the dma-ranges property below accordingly. |
| */ |
| emmc2bus: emmc2bus { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| |
| ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; |
| dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; |
| |
| emmc2: emmc2@7e340000 { |
| compatible = "brcm,bcm2711-emmc2"; |
| reg = <0x0 0x7e340000 0x100>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clocks BCM2711_CLOCK_EMMC2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3"; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_LOW)>; |
| /* This only applies to the ARMv7 stub */ |
| arm,cpu-registers-not-fw-configured; |
| }; |
| |
| cpus: cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit |
| |
| cpu0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <0>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0x0 0x000000d8>; |
| }; |
| |
| cpu1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <1>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0x0 0x000000e0>; |
| }; |
| |
| cpu2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <2>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0x0 0x000000e8>; |
| }; |
| |
| cpu3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <3>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0x0 0x000000f0>; |
| }; |
| }; |
| |
| scb { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| |
| ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, |
| <0x6 0x00000000 0x6 0x00000000 0x40000000>; |
| |
| pcie0: pcie@7d500000 { |
| compatible = "brcm,bcm2711-pcie"; |
| reg = <0x0 0x7d500000 0x9310>; |
| device_type = "pci"; |
| #address-cells = <3>; |
| #interrupt-cells = <1>; |
| #size-cells = <2>; |
| interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pcie", "msi"; |
| interrupt-map-mask = <0x0 0x0 0x0 0x7>; |
| interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 |
| IRQ_TYPE_LEVEL_HIGH>; |
| msi-controller; |
| msi-parent = <&pcie0>; |
| |
| ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 |
| 0x0 0x04000000>; |
| /* |
| * The wrapper around the PCIe block has a bug |
| * preventing it from accessing beyond the first 3GB of |
| * memory. |
| */ |
| dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 |
| 0x0 0xc0000000>; |
| brcm,enable-ssc; |
| }; |
| |
| genet: ethernet@7d580000 { |
| compatible = "brcm,bcm2711-genet-v5"; |
| reg = <0x0 0x7d580000 0x10000>; |
| #address-cells = <0x1>; |
| #size-cells = <0x1>; |
| interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| |
| genet_mdio: mdio@e14 { |
| compatible = "brcm,genet-mdio-v5"; |
| reg = <0xe14 0x8>; |
| reg-names = "mdio"; |
| #address-cells = <0x0>; |
| #size-cells = <0x1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &clk_osc { |
| clock-frequency = <54000000>; |
| }; |
| |
| &clocks { |
| compatible = "brcm,bcm2711-cprman"; |
| }; |
| |
| &cpu_thermal { |
| coefficients = <(-487) 410040>; |
| thermal-sensors = <&thermal>; |
| }; |
| |
| &dsi0 { |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &dsi1 { |
| interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| compatible = "brcm,bcm2711-dsi1"; |
| }; |
| |
| &gpio { |
| compatible = "brcm,bcm2711-gpio"; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| |
| gpclk0_gpio49: gpclk0_gpio49 { |
| pin-gpclk { |
| pins = "gpio49"; |
| function = "alt1"; |
| bias-disable; |
| }; |
| }; |
| gpclk1_gpio50: gpclk1_gpio50 { |
| pin-gpclk { |
| pins = "gpio50"; |
| function = "alt1"; |
| bias-disable; |
| }; |
| }; |
| gpclk2_gpio51: gpclk2_gpio51 { |
| pin-gpclk { |
| pins = "gpio51"; |
| function = "alt1"; |
| bias-disable; |
| }; |
| }; |
| |
| i2c0_gpio46: i2c0_gpio46 { |
| pin-sda { |
| function = "alt0"; |
| pins = "gpio46"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt0"; |
| pins = "gpio47"; |
| bias-disable; |
| }; |
| }; |
| i2c1_gpio46: i2c1_gpio46 { |
| pin-sda { |
| function = "alt1"; |
| pins = "gpio46"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt1"; |
| pins = "gpio47"; |
| bias-disable; |
| }; |
| }; |
| i2c3_gpio2: i2c3_gpio2 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio2"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio3"; |
| bias-disable; |
| }; |
| }; |
| i2c3_gpio4: i2c3_gpio4 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio4"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio5"; |
| bias-disable; |
| }; |
| }; |
| i2c4_gpio6: i2c4_gpio6 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio6"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio7"; |
| bias-disable; |
| }; |
| }; |
| i2c4_gpio8: i2c4_gpio8 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio8"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio9"; |
| bias-disable; |
| }; |
| }; |
| i2c5_gpio10: i2c5_gpio10 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio10"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio11"; |
| bias-disable; |
| }; |
| }; |
| i2c5_gpio12: i2c5_gpio12 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio12"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio13"; |
| bias-disable; |
| }; |
| }; |
| i2c6_gpio0: i2c6_gpio0 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio0"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio1"; |
| bias-disable; |
| }; |
| }; |
| i2c6_gpio22: i2c6_gpio22 { |
| pin-sda { |
| function = "alt5"; |
| pins = "gpio22"; |
| bias-pull-up; |
| }; |
| pin-scl { |
| function = "alt5"; |
| pins = "gpio23"; |
| bias-disable; |
| }; |
| }; |
| i2c_slave_gpio8: i2c_slave_gpio8 { |
| pins-i2c-slave { |
| pins = "gpio8", |
| "gpio9", |
| "gpio10", |
| "gpio11"; |
| function = "alt3"; |
| }; |
| }; |
| |
| jtag_gpio48: jtag_gpio48 { |
| pins-jtag { |
| pins = "gpio48", |
| "gpio49", |
| "gpio50", |
| "gpio51", |
| "gpio52", |
| "gpio53"; |
| function = "alt4"; |
| }; |
| }; |
| |
| mii_gpio28: mii_gpio28 { |
| pins-mii { |
| pins = "gpio28", |
| "gpio29", |
| "gpio30", |
| "gpio31"; |
| function = "alt4"; |
| }; |
| }; |
| mii_gpio36: mii_gpio36 { |
| pins-mii { |
| pins = "gpio36", |
| "gpio37", |
| "gpio38", |
| "gpio39"; |
| function = "alt5"; |
| }; |
| }; |
| |
| pcm_gpio50: pcm_gpio50 { |
| pins-pcm { |
| pins = "gpio50", |
| "gpio51", |
| "gpio52", |
| "gpio53"; |
| function = "alt2"; |
| }; |
| }; |
| |
| pwm0_0_gpio12: pwm0_0_gpio12 { |
| pin-pwm { |
| pins = "gpio12"; |
| function = "alt0"; |
| bias-disable; |
| }; |
| }; |
| pwm0_0_gpio18: pwm0_0_gpio18 { |
| pin-pwm { |
| pins = "gpio18"; |
| function = "alt5"; |
| bias-disable; |
| }; |
| }; |
| pwm1_0_gpio40: pwm1_0_gpio40 { |
| pin-pwm { |
| pins = "gpio40"; |
| function = "alt0"; |
| bias-disable; |
| }; |
| }; |
| pwm0_1_gpio13: pwm0_1_gpio13 { |
| pin-pwm { |
| pins = "gpio13"; |
| function = "alt0"; |
| bias-disable; |
| }; |
| }; |
| pwm0_1_gpio19: pwm0_1_gpio19 { |
| pin-pwm { |
| pins = "gpio19"; |
| function = "alt5"; |
| bias-disable; |
| }; |
| }; |
| pwm1_1_gpio41: pwm1_1_gpio41 { |
| pin-pwm { |
| pins = "gpio41"; |
| function = "alt0"; |
| bias-disable; |
| }; |
| }; |
| pwm0_1_gpio45: pwm0_1_gpio45 { |
| pin-pwm { |
| pins = "gpio45"; |
| function = "alt0"; |
| bias-disable; |
| }; |
| }; |
| pwm0_0_gpio52: pwm0_0_gpio52 { |
| pin-pwm { |
| pins = "gpio52"; |
| function = "alt1"; |
| bias-disable; |
| }; |
| }; |
| pwm0_1_gpio53: pwm0_1_gpio53 { |
| pin-pwm { |
| pins = "gpio53"; |
| function = "alt1"; |
| bias-disable; |
| }; |
| }; |
| |
| rgmii_gpio35: rgmii_gpio35 { |
| pin-start-stop { |
| pins = "gpio35"; |
| function = "alt4"; |
| }; |
| pin-rx-ok { |
| pins = "gpio36"; |
| function = "alt4"; |
| }; |
| }; |
| rgmii_irq_gpio34: rgmii_irq_gpio34 { |
| pin-irq { |
| pins = "gpio34"; |
| function = "alt5"; |
| }; |
| }; |
| rgmii_irq_gpio39: rgmii_irq_gpio39 { |
| pin-irq { |
| pins = "gpio39"; |
| function = "alt4"; |
| }; |
| }; |
| rgmii_mdio_gpio28: rgmii_mdio_gpio28 { |
| pins-mdio { |
| pins = "gpio28", |
| "gpio29"; |
| function = "alt5"; |
| }; |
| }; |
| rgmii_mdio_gpio37: rgmii_mdio_gpio37 { |
| pins-mdio { |
| pins = "gpio37", |
| "gpio38"; |
| function = "alt4"; |
| }; |
| }; |
| |
| spi0_gpio46: spi0_gpio46 { |
| pins-spi { |
| pins = "gpio46", |
| "gpio47", |
| "gpio48", |
| "gpio49"; |
| function = "alt2"; |
| }; |
| }; |
| spi2_gpio46: spi2_gpio46 { |
| pins-spi { |
| pins = "gpio46", |
| "gpio47", |
| "gpio48", |
| "gpio49", |
| "gpio50"; |
| function = "alt5"; |
| }; |
| }; |
| spi3_gpio0: spi3_gpio0 { |
| pins-spi { |
| pins = "gpio0", |
| "gpio1", |
| "gpio2", |
| "gpio3"; |
| function = "alt3"; |
| }; |
| }; |
| spi4_gpio4: spi4_gpio4 { |
| pins-spi { |
| pins = "gpio4", |
| "gpio5", |
| "gpio6", |
| "gpio7"; |
| function = "alt3"; |
| }; |
| }; |
| spi5_gpio12: spi5_gpio12 { |
| pins-spi { |
| pins = "gpio12", |
| "gpio13", |
| "gpio14", |
| "gpio15"; |
| function = "alt3"; |
| }; |
| }; |
| spi6_gpio18: spi6_gpio18 { |
| pins-spi { |
| pins = "gpio18", |
| "gpio19", |
| "gpio20", |
| "gpio21"; |
| function = "alt3"; |
| }; |
| }; |
| |
| uart2_gpio0: uart2_gpio0 { |
| pin-tx { |
| pins = "gpio0"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| pin-rx { |
| pins = "gpio1"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| }; |
| uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 { |
| pin-cts { |
| pins = "gpio2"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| pin-rts { |
| pins = "gpio3"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| }; |
| uart3_gpio4: uart3_gpio4 { |
| pin-tx { |
| pins = "gpio4"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| pin-rx { |
| pins = "gpio5"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| }; |
| uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 { |
| pin-cts { |
| pins = "gpio6"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| pin-rts { |
| pins = "gpio7"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| }; |
| uart4_gpio8: uart4_gpio8 { |
| pin-tx { |
| pins = "gpio8"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| pin-rx { |
| pins = "gpio9"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| }; |
| uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 { |
| pin-cts { |
| pins = "gpio10"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| pin-rts { |
| pins = "gpio11"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| }; |
| uart5_gpio12: uart5_gpio12 { |
| pin-tx { |
| pins = "gpio12"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| pin-rx { |
| pins = "gpio13"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| }; |
| uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 { |
| pin-cts { |
| pins = "gpio14"; |
| function = "alt4"; |
| bias-pull-up; |
| }; |
| pin-rts { |
| pins = "gpio15"; |
| function = "alt4"; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| &rmem { |
| #address-cells = <2>; |
| }; |
| |
| &cma { |
| /* |
| * arm64 reserves the CMA by default somewhere in ZONE_DMA32, |
| * that's not good enough for the BCM2711 as some devices can |
| * only address the lower 1G of memory (ZONE_DMA). |
| */ |
| alloc-ranges = <0x0 0x00000000 0x40000000>; |
| }; |
| |
| &i2c0 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &i2c1 { |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &mailbox { |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &sdhci { |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &sdhost { |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &spi { |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &spi1 { |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &spi2 { |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &system_timer { |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &txp { |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &uart0 { |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &uart1 { |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &usb { |
| interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &vec { |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
