| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include "msm8996.dtsi" |
| #include "pm8994.dtsi" |
| #include "pmi8994.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include <dt-bindings/sound/qcom,wcd9335.h> |
| |
| /* |
| * GPIO name legend: proper name = the GPIO line is used as GPIO |
| * NC = not connected (pin out but not routed from the chip to |
| * anything the board) |
| * "[PER]" = pin is muxed for [peripheral] (not GPIO) |
| * LSEC = Low Speed External Connector |
| * P HSEC = Primary High Speed External Connector |
| * S HSEC = Secondary High Speed External Connector |
| * J14 = Camera Connector |
| * TP = Test Points |
| * |
| * Line names are taken from the schematic "DragonBoard 820c", |
| * drawing no: LM25-P2751-1 |
| * |
| * For the lines routed to the external connectors the |
| * lines are named after the 96Boards CE Specification 1.0, |
| * Appendix "Expansion Connector Signal Description". |
| * |
| * When the 96Board naming of a line and the schematic name of |
| * the same line are in conflict, the 96Board specification |
| * takes precedence, which means that the external UART on the |
| * LSEC is named UART0 while the schematic and SoC names this |
| * UART3. This is only for the informational lines i.e. "[FOO]", |
| * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only |
| * ones actually used for GPIO. |
| */ |
| |
| / { |
| model = "Qualcomm Technologies, Inc. DB820c"; |
| compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096"; |
| |
| aliases { |
| serial0 = &blsp2_uart2; |
| serial1 = &blsp2_uart3; |
| serial2 = &blsp1_uart2; |
| i2c0 = &blsp1_i2c3; |
| i2c1 = &blsp2_i2c1; |
| i2c2 = &blsp2_i2c1; |
| spi0 = &blsp1_spi1; |
| spi1 = &blsp2_spi6; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| div1_mclk: divclk1 { |
| compatible = "gpio-gate-clock"; |
| pinctrl-0 = <&audio_mclk>; |
| pinctrl-names = "default"; |
| clocks = <&rpmcc RPM_SMD_DIV_CLK1>; |
| #clock-cells = <0>; |
| enable-gpios = <&pm8994_gpios 15 0>; |
| }; |
| |
| divclk4: divclk4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "divclk4"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&divclk4_pin_a>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&volume_up_gpio>; |
| |
| button { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| usb2_id: usb2-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb2_vbus_det_gpio>; |
| }; |
| |
| usb3_id: usb3-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb3_vbus_det_gpio>; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| wlan_en: wlan-en-1-8v { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_en_gpios>; |
| compatible = "regulator-fixed"; |
| regulator-name = "wlan-en-regulator"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| gpio = <&pm8994_gpios 8 0>; |
| |
| /* WLAN card specific delay */ |
| startup-delay-us = <70000>; |
| enable-active-high; |
| }; |
| }; |
| |
| &blsp1_i2c3 { |
| /* On Low speed expansion: LS-I2C0 */ |
| status = "okay"; |
| }; |
| |
| &blsp1_spi1 { |
| /* On Low speed expansion */ |
| status = "okay"; |
| }; |
| |
| &blsp1_uart2 { |
| label = "BT-UART"; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,qca6174-bt"; |
| |
| /* bt_disable_n gpio */ |
| enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; |
| |
| clocks = <&divclk4>; |
| }; |
| }; |
| |
| &adsp_pil { |
| status = "okay"; |
| firmware-name = "qcom/apq8096/adsp.mbn"; |
| }; |
| |
| &blsp2_i2c1 { |
| /* On High speed expansion: HS-I2C2 */ |
| status = "okay"; |
| }; |
| |
| &blsp2_i2c1 { |
| /* On Low speed expansion: LS-I2C1 */ |
| status = "okay"; |
| }; |
| |
| &blsp2_spi6 { |
| /* On High speed expansion */ |
| status = "okay"; |
| }; |
| |
| &blsp2_uart2 { |
| label = "LS-UART1"; |
| status = "okay"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart2_2pins_default>; |
| pinctrl-1 = <&blsp2_uart2_2pins_sleep>; |
| }; |
| |
| &blsp2_uart3 { |
| label = "LS-UART0"; |
| status = "disabled"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart3_4pins_default>; |
| pinctrl-1 = <&blsp2_uart3_4pins_sleep>; |
| }; |
| |
| &camss { |
| vdda-supply = <&vreg_l2a_1p25>; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| }; |
| |
| &hsusb_phy1 { |
| status = "okay"; |
| |
| vdd-supply = <&vreg_l28a_0p925>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| }; |
| |
| &hsusb_phy2 { |
| status = "okay"; |
| |
| vdd-supply = <&vreg_l28a_0p925>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| }; |
| |
| &mdp { |
| status = "okay"; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_hdmi { |
| status = "okay"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>; |
| pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>; |
| |
| core-vdda-supply = <&vreg_l12a_1p8>; |
| core-vcc-supply = <&vreg_s4a_1p8>; |
| }; |
| |
| &mdss_hdmi_phy { |
| status = "okay"; |
| |
| vddio-supply = <&vreg_l12a_1p8>; |
| vcca-supply = <&vreg_l28a_0p925>; |
| #phy-cells = <0>; |
| }; |
| |
| &mmcc { |
| vdd-gfx-supply = <&vdd_gfx>; |
| }; |
| |
| &mss_pil { |
| status = "okay"; |
| pll-supply = <&vreg_l12a_1p8>; |
| firmware-name = "qcom/apq8096/mba.mbn", "qcom/apq8096/modem.mbn"; |
| }; |
| |
| &pm8994_resin { |
| status = "okay"; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| |
| &tlmm { |
| gpio-line-names = |
| "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */ |
| "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */ |
| "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */ |
| "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */ |
| "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */ |
| "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */ |
| "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */ |
| "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */ |
| "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */ |
| "TP93", /* GPIO_9 */ |
| "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */ |
| "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */ |
| "NC", /* GPIO_12 */ |
| "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */ |
| "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */ |
| "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */ |
| "TP99", /* GPIO_16 */ |
| "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */ |
| "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */ |
| "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */ |
| "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */ |
| "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */ |
| "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */ |
| "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */ |
| "GPIO-D", /* GPIO_24, LSEC pin 26 */ |
| "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */ |
| "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */ |
| "BLSP6_I2C_SDA", /* GPIO_27 */ |
| "BLSP6_I2C_SCL", /* GPIO_28 */ |
| "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */ |
| "GPIO30", /* GPIO_30, S HSEC pin 4 */ |
| "HDMI_CEC", /* GPIO_31 */ |
| "HDMI_DDC_CLOCK", /* GPIO_32 */ |
| "HDMI_DDC_DATA", /* GPIO_33 */ |
| "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */ |
| "PCIE0_RST_N", /* GPIO_35 */ |
| "PCIE0_CLKREQ_N", /* GPIO_36 */ |
| "PCIE0_WAKE", /* GPIO_37 */ |
| "SD_CARD_DET_N", /* GPIO_38 */ |
| "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */ |
| "W_DISABLE_N", /* GPIO_40 */ |
| "[BLSP9_UART_TX]", /* GPIO_41 */ |
| "[BLSP9_UART_RX]", /* GPIO_42 */ |
| "[BLSP2_UART_CTS_N]", /* GPIO_43 */ |
| "[BLSP2_UART_RFR_N]", /* GPIO_44 */ |
| "[BLSP3_UART_TX]", /* GPIO_45 */ |
| "[BLSP3_UART_RX]", /* GPIO_46 */ |
| "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */ |
| "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */ |
| "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */ |
| "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */ |
| "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */ |
| "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */ |
| "[CODEC_INT1_N]", /* GPIO_53 */ |
| "[CODEC_INT2_N]", /* GPIO_54 */ |
| "[BLSP7_I2C_SDA]", /* GPIO_55 */ |
| "[BLSP7_I2C_SCL]", /* GPIO_56 */ |
| "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */ |
| "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */ |
| "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */ |
| "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */ |
| "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */ |
| "GPIO-E", /* GPIO_62, LSEC pin 27 */ |
| "TP87", /* GPIO_63 */ |
| "[CODEC_RST_N]", /* GPIO_64 */ |
| "[PCM1_CLK]", /* GPIO_65 */ |
| "[PCM1_SYNC]", /* GPIO_66 */ |
| "[PCM1_DIN]", /* GPIO_67 */ |
| "[PCM1_DOUT]", /* GPIO_68 */ |
| "AUDIO_REF_CLK", /* GPIO_69 */ |
| "SLIMBUS_CLK", /* GPIO_70 */ |
| "SLIMBUS_DATA0", /* GPIO_71 */ |
| "SLIMBUS_DATA1", /* GPIO_72 */ |
| "NC", /* GPIO_73 */ |
| "NC", /* GPIO_74 */ |
| "NC", /* GPIO_75 */ |
| "NC", /* GPIO_76 */ |
| "TP94", /* GPIO_77 */ |
| "NC", /* GPIO_78 */ |
| "TP95", /* GPIO_79 */ |
| "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */ |
| "TP88", /* GPIO_81 */ |
| "TP89", /* GPIO_82 */ |
| "TP90", /* GPIO_83 */ |
| "TP91", /* GPIO_84 */ |
| "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */ |
| "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */ |
| "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */ |
| "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */ |
| "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */ |
| "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */ |
| "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */ |
| "NC", /* GPIO_92 */ |
| "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */ |
| "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */ |
| "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */ |
| "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */ |
| "NC", /* GPIO_97 */ |
| "CAM1_STANDBY_N", /* GPIO_98 */ |
| "NC", /* GPIO_99 */ |
| "NC", /* GPIO_100 */ |
| "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */ |
| "BOOT_CONFIG1", /* GPIO_102 */ |
| "USB_HUB_RESET", /* GPIO_103 */ |
| "CAM1_RST_N", /* GPIO_104 */ |
| "NC", /* GPIO_105 */ |
| "NC", /* GPIO_106 */ |
| "NC", /* GPIO_107 */ |
| "NC", /* GPIO_108 */ |
| "NC", /* GPIO_109 */ |
| "NC", /* GPIO_110 */ |
| "NC", /* GPIO_111 */ |
| "NC", /* GPIO_112 */ |
| "PMI8994_BUA", /* GPIO_113 */ |
| "PCIE2_RST_N", /* GPIO_114 */ |
| "PCIE2_CLKREQ_N", /* GPIO_115 */ |
| "PCIE2_WAKE", /* GPIO_116 */ |
| "SSC_IRQ_0", /* GPIO_117 */ |
| "SSC_IRQ_1", /* GPIO_118 */ |
| "SSC_IRQ_2", /* GPIO_119 */ |
| "NC", /* GPIO_120 */ |
| "GPIO121", /* GPIO_121, S HSEC pin 2 */ |
| "NC", /* GPIO_122 */ |
| "SSC_IRQ_6", /* GPIO_123 */ |
| "SSC_IRQ_7", /* GPIO_124 */ |
| "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */ |
| "BOOT_CONFIG5", /* GPIO_126 */ |
| "NC", /* GPIO_127 */ |
| "NC", /* GPIO_128 */ |
| "BOOT_CONFIG7", /* GPIO_129 */ |
| "PCIE1_RST_N", /* GPIO_130 */ |
| "PCIE1_CLKREQ_N", /* GPIO_131 */ |
| "PCIE1_WAKE", /* GPIO_132 */ |
| "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */ |
| "NC", /* GPIO_134 */ |
| "NC", /* GPIO_135 */ |
| "BOOT_CONFIG8", /* GPIO_136 */ |
| "NC", /* GPIO_137 */ |
| "NC", /* GPIO_138 */ |
| "GPS_SSBI2", /* GPIO_139 */ |
| "GPS_SSBI1", /* GPIO_140 */ |
| "NC", /* GPIO_141 */ |
| "NC", /* GPIO_142 */ |
| "NC", /* GPIO_143 */ |
| "BOOT_CONFIG6", /* GPIO_144 */ |
| "NC", /* GPIO_145 */ |
| "NC", /* GPIO_146 */ |
| "NC", /* GPIO_147 */ |
| "NC", /* GPIO_148 */ |
| "NC"; /* GPIO_149 */ |
| |
| sdc2_cd_on: sdc2-cd-on-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <16>; |
| }; |
| |
| sdc2_cd_off: sdc2-cd-off-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| hdmi_hpd_active: hdmi-hpd-active-state { |
| pins = "gpio34"; |
| function = "hdmi_hot"; |
| bias-pull-down; |
| drive-strength = <16>; |
| }; |
| |
| hdmi_hpd_suspend: hdmi-hpd-suspend-state { |
| pins = "gpio34"; |
| function = "hdmi_hot"; |
| bias-pull-down; |
| drive-strength = <2>; |
| }; |
| |
| hdmi_ddc_active: hdmi-ddc-active-state { |
| pins = "gpio32", "gpio33"; |
| function = "hdmi_ddc"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| hdmi_ddc_suspend: hdmi-ddc-suspend-state { |
| pins = "gpio32", "gpio33"; |
| function = "hdmi_ddc"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| |
| &pcie0 { |
| status = "okay"; |
| perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; |
| vddpe-3v3-supply = <&wlan_en>; |
| vdda-supply = <&vreg_l28a_0p925>; |
| }; |
| |
| &pcie1 { |
| status = "okay"; |
| perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>; |
| vdda-supply = <&vreg_l28a_0p925>; |
| }; |
| |
| &pcie2 { |
| status = "okay"; |
| perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>; |
| vdda-supply = <&vreg_l28a_0p925>; |
| }; |
| |
| &pcie_phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l28a_0p925>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| }; |
| |
| &pm8994_gpios { |
| gpio-line-names = |
| "NC", |
| "KEY_VOLP_N", |
| "NC", |
| "BL1_PWM", |
| "GPIO-F", /* BL0_PWM, LSEC pin 28 */ |
| "BL1_EN", |
| "NC", |
| "WLAN_EN", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "NC", |
| "DIVCLK1", |
| "DIVCLK2", |
| "DIVCLK3", |
| "DIVCLK4", |
| "BT_EN", |
| "PMIC_SLB", |
| "PMIC_BUA", |
| "USB_VBUS_DET"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>; |
| |
| ls_exp_gpio_f: pm8994-gpio5-state { |
| pinconf { |
| pins = "gpio5"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| output-low; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| }; |
| }; |
| |
| bt_en_gpios: bt-en-pios-state { |
| pinconf { |
| pins = "gpio19"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| output-low; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| bias-pull-down; |
| }; |
| }; |
| |
| wlan_en_gpios: wlan-en-gpios-state { |
| pinconf { |
| pins = "gpio8"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| output-low; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| bias-pull-down; |
| }; |
| }; |
| |
| audio_mclk: clk-div1-state { |
| pinconf { |
| pins = "gpio15"; |
| function = "func1"; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| }; |
| }; |
| |
| volume_up_gpio: pm8996-gpio2-state { |
| pinconf { |
| pins = "gpio2"; |
| function = "normal"; |
| input-enable; |
| drive-push-pull; |
| bias-pull-up; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| }; |
| }; |
| |
| divclk4_pin_a: divclk4-state { |
| pinconf { |
| pins = "gpio18"; |
| function = PMIC_GPIO_FUNC_FUNC2; |
| |
| bias-disable; |
| power-source = <PM8994_GPIO_S4>; |
| }; |
| }; |
| |
| usb3_vbus_det_gpio: pm8996-gpio22-state { |
| pinconf { |
| pins = "gpio22"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| input-enable; |
| bias-pull-down; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| }; |
| }; |
| }; |
| |
| &pm8994_mpps { |
| gpio-line-names = |
| "VDDPX_BIAS", |
| "WIFI_LED", |
| "NC", |
| "BT_LED", |
| "PM_MPP05", |
| "PM_MPP06", |
| "PM_MPP07", |
| "NC"; |
| }; |
| |
| &pm8994_spmi_regulators { |
| qcom,saw-reg = <&saw3>; |
| vdd_s11-supply = <&vph_pwr>; |
| |
| s9 { |
| qcom,saw-slave; |
| }; |
| s10 { |
| qcom,saw-slave; |
| }; |
| s11 { |
| qcom,saw-leader; |
| regulator-name = "VDD_APCC"; |
| regulator-always-on; |
| regulator-min-microvolt = <980000>; |
| regulator-max-microvolt = <980000>; |
| }; |
| }; |
| |
| &pmi8994_gpios { |
| gpio-line-names = |
| "NC", |
| "SPKR_AMP_EN1", |
| "SPKR_AMP_EN2", |
| "TP61", |
| "NC", |
| "USB2_VBUS_DET", |
| "NC", |
| "NC", |
| "NC", |
| "NC"; |
| |
| usb2_vbus_det_gpio: pmi8996-gpio6-state { |
| pinconf { |
| pins = "gpio6"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| input-enable; |
| bias-pull-down; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| power-source = <PM8994_GPIO_S4>; /* 1.8V */ |
| }; |
| }; |
| }; |
| |
| &pmi8994_lpg { |
| qcom,power-source = <1>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmi8994_mpp2_userled4>; |
| |
| qcom,dtest = <0 0>, |
| <0 0>, |
| <0 0>, |
| <4 1>; |
| |
| status = "okay"; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_HEARTBEAT; |
| function-enumerator = <1>; |
| |
| linux,default-trigger = "heartbeat"; |
| default-state = "on"; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_HEARTBEAT; |
| function-enumerator = <0>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_HEARTBEAT; |
| function-enumerator = <2>; |
| }; |
| |
| led@4 { |
| reg = <4>; |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_HEARTBEAT; |
| function-enumerator = <3>; |
| }; |
| }; |
| |
| &pmi8994_mpps { |
| pmi8994_mpp2_userled4: mpp2-userled4-state { |
| pins = "mpp2"; |
| function = "sink"; |
| |
| output-low; |
| qcom,dtest = <4>; |
| }; |
| }; |
| |
| &pmi8994_spmi_regulators { |
| vdd_s2-supply = <&vph_pwr>; |
| |
| vdd_gfx: s2 { |
| regulator-name = "VDD_GFX"; |
| regulator-min-microvolt = <980000>; |
| regulator-max-microvolt = <980000>; |
| }; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8994-regulators"; |
| |
| vdd_s1-supply = <&vph_pwr>; |
| vdd_s2-supply = <&vph_pwr>; |
| vdd_s3-supply = <&vph_pwr>; |
| vdd_s4-supply = <&vph_pwr>; |
| vdd_s5-supply = <&vph_pwr>; |
| vdd_s6-supply = <&vph_pwr>; |
| vdd_s7-supply = <&vph_pwr>; |
| vdd_s8-supply = <&vph_pwr>; |
| vdd_s9-supply = <&vph_pwr>; |
| vdd_s10-supply = <&vph_pwr>; |
| vdd_s11-supply = <&vph_pwr>; |
| vdd_s12-supply = <&vph_pwr>; |
| vdd_l1-supply = <&vreg_s1b_1p025>; |
| vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>; |
| vdd_l3_l11-supply = <&vreg_s3a_1p3>; |
| vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>; |
| vdd_l5_l7-supply = <&vreg_s5a_2p15>; |
| vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>; |
| vdd_l8_l16_l30-supply = <&vph_pwr>; |
| vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>; |
| vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>; |
| vdd_l14_l15-supply = <&vreg_s5a_2p15>; |
| vdd_l17_l29-supply = <&vph_pwr_bbyp>; |
| vdd_l20_l21-supply = <&vph_pwr_bbyp>; |
| vdd_l25-supply = <&vreg_s3a_1p3>; |
| vdd_lvs1_2-supply = <&vreg_s4a_1p8>; |
| |
| vreg_s3a_1p3: s3 { |
| regulator-name = "vreg_s3a_1p3"; |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| /** |
| * 1.8v required on LS expansion |
| * for mezzanine boards |
| */ |
| vreg_s4a_1p8: s4 { |
| regulator-name = "vreg_s4a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| vreg_s5a_2p15: s5 { |
| regulator-name = "vreg_s5a_2p15"; |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| }; |
| vreg_s7a_1p0: s7 { |
| regulator-name = "vreg_s7a_1p0"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_l1a_1p0: l1 { |
| regulator-name = "vreg_l1a_1p0"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| vreg_l2a_1p25: l2 { |
| regulator-name = "vreg_l2a_1p25"; |
| regulator-min-microvolt = <1250000>; |
| regulator-max-microvolt = <1250000>; |
| }; |
| vreg_l3a_0p875: l3 { |
| regulator-name = "vreg_l3a_0p875"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| }; |
| vreg_l4a_1p225: l4 { |
| regulator-name = "vreg_l4a_1p225"; |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| vreg_l6a_1p2: l6 { |
| regulator-name = "vreg_l6a_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| vreg_l8a_1p8: l8 { |
| regulator-name = "vreg_l8a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l9a_1p8: l9 { |
| regulator-name = "vreg_l9a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l10a_1p8: l10 { |
| regulator-name = "vreg_l10a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l11a_1p15: l11 { |
| regulator-name = "vreg_l11a_1p15"; |
| regulator-min-microvolt = <1150000>; |
| regulator-max-microvolt = <1150000>; |
| }; |
| vreg_l12a_1p8: l12 { |
| regulator-name = "vreg_l12a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l13a_2p95: l13 { |
| regulator-name = "vreg_l13a_2p95"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| vreg_l14a_1p8: l14 { |
| regulator-name = "vreg_l14a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l15a_1p8: l15 { |
| regulator-name = "vreg_l15a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l16a_2p7: l16 { |
| regulator-name = "vreg_l16a_2p7"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| vreg_l17a_2p8: l17 { |
| regulator-name = "vreg_l17a_2p8"; |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <2500000>; |
| }; |
| vreg_l18a_2p85: l18 { |
| regulator-name = "vreg_l18a_2p85"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2900000>; |
| }; |
| vreg_l19a_2p8: l19 { |
| regulator-name = "vreg_l19a_2p8"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| vreg_l20a_2p95: l20 { |
| regulator-name = "vreg_l20a_2p95"; |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| vreg_l21a_2p95: l21 { |
| regulator-name = "vreg_l21a_2p95"; |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| regulator-system-load = <200000>; |
| }; |
| vreg_l22a_3p0: l22 { |
| regulator-name = "vreg_l22a_3p0"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| vreg_l23a_2p8: l23 { |
| regulator-name = "vreg_l23a_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| vreg_l24a_3p075: l24 { |
| regulator-name = "vreg_l24a_3p075"; |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| vreg_l25a_1p2: l25 { |
| regulator-name = "vreg_l25a_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-allow-set-load; |
| }; |
| vreg_l26a_0p8: l27 { |
| regulator-name = "vreg_l26a_0p8"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| vreg_l28a_0p925: l28 { |
| regulator-name = "vreg_l28a_0p925"; |
| regulator-min-microvolt = <925000>; |
| regulator-max-microvolt = <925000>; |
| regulator-allow-set-load; |
| }; |
| vreg_l29a_2p8: l29 { |
| regulator-name = "vreg_l29a_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| vreg_l30a_1p8: l30 { |
| regulator-name = "vreg_l30a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| vreg_l32a_1p8: l32 { |
| regulator-name = "vreg_l32a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { |
| regulator-name = "vreg_lvs1a_1p8"; |
| }; |
| |
| vreg_lvs2a_1p8: lvs2 { |
| regulator-name = "vreg_lvs2a_1p8"; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pmi8994-regulators"; |
| |
| vdd_s1-supply = <&vph_pwr>; |
| vdd_s2-supply = <&vph_pwr>; |
| vdd_s3-supply = <&vph_pwr>; |
| vdd_bst_byp-supply = <&vph_pwr>; |
| |
| vph_pwr_bbyp: boost-bypass { |
| regulator-name = "vph_pwr_bbyp"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vreg_s1b_1p025: s1 { |
| regulator-name = "vreg_s1b_1p025"; |
| regulator-min-microvolt = <1025000>; |
| regulator-max-microvolt = <1025000>; |
| }; |
| }; |
| }; |
| |
| &sdhc2 { |
| /* External SD card */ |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>; |
| cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&vreg_l21a_2p95>; |
| vqmmc-supply = <&vreg_l13a_2p95>; |
| status = "okay"; |
| }; |
| |
| &q6asmdai { |
| dai@0 { |
| reg = <0>; |
| }; |
| |
| dai@1 { |
| reg = <1>; |
| }; |
| |
| dai@2 { |
| reg = <2>; |
| }; |
| }; |
| |
| &slim_msm { |
| status = "okay"; |
| |
| slim@1 { |
| reg = <1>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| tasha_ifd: tas-ifd@0,0 { |
| compatible = "slim217,1a0"; |
| reg = <0 0>; |
| }; |
| |
| wcd9335: codec@1,0 { |
| compatible = "slim217,1a0"; |
| reg = <1 0>; |
| |
| clock-names = "mclk", "slimbus"; |
| clocks = <&div1_mclk>, |
| <&rpmcc RPM_SMD_BB_CLK1>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <54 IRQ_TYPE_LEVEL_HIGH>, |
| <53 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "intr1", "intr2"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| pinctrl-0 = <&cdc_reset_active &wcd_intr_default>; |
| pinctrl-names = "default"; |
| |
| reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>; |
| slim-ifc-dev = <&tasha_ifd>; |
| |
| #sound-dai-cells = <1>; |
| |
| vdd-buck-supply = <&vreg_s4a_1p8>; |
| vdd-buck-sido-supply = <&vreg_s4a_1p8>; |
| vdd-tx-supply = <&vreg_s4a_1p8>; |
| vdd-rx-supply = <&vreg_s4a_1p8>; |
| vdd-io-supply = <&vreg_s4a_1p8>; |
| }; |
| }; |
| }; |
| |
| &sound { |
| compatible = "qcom,apq8096-sndcard"; |
| model = "DB820c"; |
| audio-routing = "RX_BIAS", "MCLK", |
| "MM_DL1", "MultiMedia1 Playback", |
| "MM_DL2", "MultiMedia2 Playback", |
| "MultiMedia3 Capture", "MM_UL3"; |
| |
| mm1-dai-link { |
| link-name = "MultiMedia1"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| mm2-dai-link { |
| link-name = "MultiMedia2"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| mm3-dai-link { |
| link-name = "MultiMedia3"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| hdmi-dai-link { |
| link-name = "HDMI"; |
| cpu { |
| sound-dai = <&q6afedai HDMI_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&mdss_hdmi 0>; |
| }; |
| }; |
| |
| slim-dai-link { |
| link-name = "SLIM Playback"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_6_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9335 AIF4_PB>; |
| }; |
| }; |
| |
| slimcap-dai-link { |
| link-name = "SLIM Capture"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9335 AIF1_CAP>; |
| }; |
| }; |
| }; |
| |
| &ufsphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l28a_0p925>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| }; |
| |
| &ufshc { |
| status = "okay"; |
| |
| vcc-supply = <&vreg_l20a_2p95>; |
| vccq-supply = <&vreg_l25a_1p2>; |
| vccq2-supply = <&vreg_s4a_1p8>; |
| vdd-hba-supply = <&vreg_l25a_1p2>; |
| |
| vcc-max-microamp = <600000>; |
| vccq-max-microamp = <450000>; |
| vccq2-max-microamp = <450000>; |
| }; |
| |
| &usb2 { |
| status = "okay"; |
| extcon = <&usb2_id>; |
| }; |
| |
| &usb2_dwc3 { |
| extcon = <&usb2_id>; |
| dr_mode = "otg"; |
| maximum-speed = "high-speed"; |
| }; |
| |
| &usb3 { |
| status = "okay"; |
| extcon = <&usb3_id>; |
| }; |
| |
| &usb3_dwc3 { |
| extcon = <&usb3_id>; |
| dr_mode = "otg"; |
| }; |
| |
| &usb3phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l28a_0p925>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| }; |
| |
| &venus { |
| status = "okay"; |
| }; |
