| // SPDX-License-Identifier: BSD-3-Clause |
| /* Copyright (c) 2022, The Linux Foundation. All rights reserved. */ |
| |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| / { |
| thermal-zones { |
| pm8953-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| |
| thermal-sensors = <&pm8953_temp>; |
| |
| trips { |
| trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| |
| trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pmic@0 { |
| compatible = "qcom,pm8953", "qcom,spmi-pmic"; |
| reg = <0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8953_pon: pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x800>; |
| mode-bootloader = <0x2>; |
| mode-recovery = <0x1>; |
| |
| pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x00 0x08 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| }; |
| |
| pm8953_resin: resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <0x00 0x08 1 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| status = "disabled"; |
| }; |
| }; |
| |
| pm8953_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| io-channels = <&pm8953_vadc VADC_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8953_vadc: adc@3100 { |
| compatible = "qcom,spmi-vadc"; |
| reg = <0x3100>; |
| interrupts = <0x00 0x31 0x00 0x01>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| channel@8 { |
| reg = <VADC_DIE_TEMP>; |
| }; |
| channel@9 { |
| reg = <VADC_REF_625MV>; |
| }; |
| channel@a { |
| reg = <VADC_REF_1250MV>; |
| }; |
| channel@c { |
| reg = <VADC_SPARE1>; |
| }; |
| channel@e { |
| reg = <VADC_GND_REF>; |
| }; |
| channel@f { |
| reg = <VADC_VDD_VADC>; |
| }; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>, <0x6100>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| pm8953_gpios: gpio@c000 { |
| compatible = "qcom,pm8953-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pm8953_gpios 0 0 8>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@1 { |
| compatible = "qcom,pm8953", "qcom,spmi-pmic"; |
| reg = <1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
