| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* Copyright 2018 Google LLC. */ |
| |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| thermal-zones { |
| pm8998-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&pm8998_temp>; |
| |
| trips { |
| pm8998_alert0: pm8998-alert0 { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| pm8998_crit: pm8998-crit { |
| temperature = <125000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pm8998_lsid0: pmic@0 { |
| compatible = "qcom,pm8998", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8998_pon: pon@800 { |
| compatible = "qcom,pm8998-pon"; |
| |
| reg = <0x800>; |
| mode-bootloader = <0x2>; |
| mode-recovery = <0x1>; |
| |
| pm8998_pwrkey: pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| }; |
| |
| pm8998_resin: resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| status = "disabled"; |
| }; |
| }; |
| |
| pm8998_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| io-channels = <&pm8998_adc ADC5_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8998_coincell: charger@2800 { |
| compatible = "qcom,pm8998-coincell", "qcom,pm8941-coincell"; |
| reg = <0x2800>; |
| |
| status = "disabled"; |
| }; |
| |
| pm8998_adc: adc@3100 { |
| compatible = "qcom,spmi-adc-rev2"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| channel@6 { |
| reg = <ADC5_DIE_TEMP>; |
| label = "die_temp"; |
| }; |
| }; |
| |
| pm8998_adc_tm: adc-tm@3400 { |
| compatible = "qcom,spmi-adc-tm-hc"; |
| reg = <0x3400>; |
| interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>, <0x6100>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| pm8998_gpios: gpio@c000 { |
| compatible = "qcom,pm8998-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pm8998_gpios 0 0 26>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| }; |
| |
| pm8998_lsid1: pmic@1 { |
| compatible = "qcom,pm8998", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
