| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Google Trogdor board device tree source |
| * |
| * Copyright 2020 Google LLC. |
| */ |
| |
| /dts-v1/; |
| |
| #include "sc7180-trogdor.dtsi" |
| /* Must come after sc7180-trogdor.dtsi to modify cros_ec */ |
| #include <arm/cros-ec-keyboard.dtsi> |
| #include "sc7180-trogdor-rt5682i-sku.dtsi" |
| #include "sc7180-trogdor-ti-sn65dsi86.dtsi" |
| |
| / { |
| model = "Google Trogdor (rev1+)"; |
| compatible = "google,trogdor", "qcom,sc7180"; |
| }; |
| |
| &ap_tp_i2c { |
| status = "okay"; |
| }; |
| |
| ap_ts_pen_1v8: &i2c4 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| ap_ts: touchscreen@10 { |
| compatible = "elan,ekth3500"; |
| reg = <0x10>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| |
| vcc33-supply = <&pp3300_ts>; |
| |
| reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| &panel { |
| compatible = "auo,b116xa01"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| }; |
| |
| &trackpad { |
| interrupts = <58 IRQ_TYPE_EDGE_FALLING>; |
| }; |
| |
| &usb_hub_2_x { |
| vdd-supply = <&pp3300_l7c>; |
| }; |
| |
| &usb_hub_3_x { |
| vdd-supply = <&pp3300_l7c>; |
| }; |
| |
| /* PINCTRL - modifications to sc7180-trogdor.dtsi */ |
| |
| &trackpad_int_1v8_odl { |
| pins = "gpio58"; |
| }; |
| |
| /* PINCTRL - board-specific pinctrl */ |
| |
| &tlmm { |
| gpio-line-names = "ESIM_MISO", |
| "ESIM_MOSI", |
| "ESIM_CLK", |
| "ESIM_CS_L", |
| "FP_TO_AP_IRQ_L", |
| "FP_RST_L", |
| "AP_TP_I2C_SDA", |
| "AP_TP_I2C_SCL", |
| "TS_RESET_L", |
| "TS_INT_L", |
| "FPMCU_BOOT0", |
| "EDP_BRIJ_IRQ", |
| "AP_EDP_BKLTEN", |
| "", |
| "", |
| "EDP_BRIJ_I2C_SDA", |
| "EDP_BRIJ_I2C_SCL", |
| "HUB_RST_L", |
| "PEN_RST_ODL", |
| "AP_RAM_ID1", |
| "AP_RAM_ID2", |
| "PEN_IRQ_L", |
| "FPMCU_SEL", |
| "AMP_EN", |
| "P_SENSOR_INT_L", |
| "AP_SAR_SENSOR_SDA", |
| "AP_SAR_SENSOR_SCL", |
| "", |
| "HP_IRQ", |
| "AP_RAM_ID0", |
| "EN_PP3300_DX_EDP", |
| "AP_BRD_ID2", |
| "BRIJ_SUSPEND", |
| "AP_BRD_ID0", |
| "AP_H1_SPI_MISO", |
| "AP_H1_SPI_MOSI", |
| "AP_H1_SPI_CLK", |
| "AP_H1_SPI_CS_L", |
| "", |
| "", |
| "", |
| "", |
| "H1_AP_INT_ODL", |
| "", |
| "UART_AP_TX_DBG_RX", |
| "UART_DBG_TX_AP_RX", |
| "HP_I2C_SDA", |
| "HP_I2C_SCL", |
| "FORCED_USB_BOOT", |
| "", |
| "", |
| "AMP_DIN", |
| "PEN_PDCT_L", |
| "HP_BCLK", |
| "HP_LRCLK", |
| "HP_DOUT", |
| "HP_DIN", |
| "HP_MCLK", |
| "TRACKPAD_INT_1V8_ODL", |
| "AP_EC_SPI_MISO", |
| "AP_EC_SPI_MOSI", |
| "AP_EC_SPI_CLK", |
| "AP_EC_SPI_CS_L", |
| "AP_SPI_CLK", |
| "AP_SPI_MOSI", |
| "AP_SPI_MISO", |
| /* |
| * AP_FLASH_WP_L is crossystem ABI. Schematics |
| * call it BIOS_FLASH_WP_L. |
| */ |
| "AP_FLASH_WP_L", |
| "DBG_SPI_HOLD_L", |
| "AP_SPI_CS0_L", |
| "SD_CD_ODL", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "UIM2_DATA", |
| "UIM2_CLK", |
| "UIM2_RST", |
| "UIM2_PRESENT", |
| "UIM1_DATA", |
| "UIM1_CLK", |
| "UIM1_RST", |
| "", |
| "EN_PP3300_CODEC", |
| "EN_PP3300_HUB", |
| "", |
| "AP_SPI_FP_MISO", |
| "AP_SPI_FP_MOSI", |
| "AP_SPI_FP_CLK", |
| "AP_SPI_FP_CS_L", |
| "AP_SKU_ID1", |
| "AP_RST_REQ", |
| "", |
| "AP_BRD_ID1", |
| "AP_EC_INT_L", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "EDP_BRIJ_EN", |
| "AP_SKU_ID0", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AP_TS_PEN_I2C_SDA", |
| "AP_TS_PEN_I2C_SCL", |
| "DP_HOT_PLUG_DET", |
| "EC_IN_RW_ODL"; |
| }; |
