| /* |
| * linux/arch/arm/mach-integrator/integrator_cp.c |
| * |
| * Copyright (C) 2003 Deep Blue Solutions Ltd |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License. |
| */ |
| #include <linux/types.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/list.h> |
| #include <linux/platform_device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/string.h> |
| #include <linux/device.h> |
| #include <linux/amba/bus.h> |
| #include <linux/amba/kmi.h> |
| #include <linux/amba/clcd.h> |
| #include <linux/amba/mmci.h> |
| #include <linux/io.h> |
| #include <linux/gfp.h> |
| #include <linux/clkdev.h> |
| #include <linux/mtd/physmap.h> |
| |
| #include <mach/hardware.h> |
| #include <mach/platform.h> |
| #include <asm/setup.h> |
| #include <asm/mach-types.h> |
| #include <asm/hardware/arm_timer.h> |
| #include <asm/hardware/icst.h> |
| |
| #include <mach/cm.h> |
| #include <mach/lm.h> |
| #include <mach/irqs.h> |
| |
| #include <asm/mach/arch.h> |
| #include <asm/mach/irq.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/time.h> |
| |
| #include <asm/hardware/timer-sp.h> |
| |
| #include <plat/clcd.h> |
| #include <plat/fpga-irq.h> |
| #include <plat/sched_clock.h> |
| |
| #include "common.h" |
| |
| #define INTCP_PA_FLASH_BASE 0x24000000 |
| #define INTCP_FLASH_SIZE SZ_32M |
| |
| #define INTCP_PA_CLCD_BASE 0xc0000000 |
| |
| #define INTCP_VA_CIC_BASE __io_address(INTEGRATOR_HDR_BASE + 0x40) |
| #define INTCP_VA_PIC_BASE __io_address(INTEGRATOR_IC_BASE) |
| #define INTCP_VA_SIC_BASE __io_address(INTEGRATOR_CP_SIC_BASE) |
| |
| #define INTCP_ETH_SIZE 0x10 |
| |
| #define INTCP_VA_CTRL_BASE IO_ADDRESS(INTEGRATOR_CP_CTL_BASE) |
| #define INTCP_FLASHPROG 0x04 |
| #define CINTEGRATOR_FLASHPROG_FLVPPEN (1 << 0) |
| #define CINTEGRATOR_FLASHPROG_FLWREN (1 << 1) |
| |
| /* |
| * Logical Physical |
| * f1000000 10000000 Core module registers |
| * f1100000 11000000 System controller registers |
| * f1200000 12000000 EBI registers |
| * f1300000 13000000 Counter/Timer |
| * f1400000 14000000 Interrupt controller |
| * f1600000 16000000 UART 0 |
| * f1700000 17000000 UART 1 |
| * f1a00000 1a000000 Debug LEDs |
| * fc900000 c9000000 GPIO |
| * fca00000 ca000000 SIC |
| * fcb00000 cb000000 CP system control |
| */ |
| |
| static struct map_desc intcp_io_desc[] __initdata = { |
| { |
| .virtual = IO_ADDRESS(INTEGRATOR_HDR_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_HDR_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_SC_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_SC_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_EBI_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_EBI_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_CT_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_CT_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_IC_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_IC_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_UART0_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_UART0_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_UART1_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_UART1_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_DBG_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_DBG_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_CP_GPIO_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_CP_GPIO_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_CP_SIC_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_CP_SIC_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| }, { |
| .virtual = IO_ADDRESS(INTEGRATOR_CP_CTL_BASE), |
| .pfn = __phys_to_pfn(INTEGRATOR_CP_CTL_BASE), |
| .length = SZ_4K, |
| .type = MT_DEVICE |
| } |
| }; |
| |
| static void __init intcp_map_io(void) |
| { |
| iotable_init(intcp_io_desc, ARRAY_SIZE(intcp_io_desc)); |
| } |
| |
| static struct fpga_irq_data cic_irq_data = { |
| .base = INTCP_VA_CIC_BASE, |
| .irq_start = IRQ_CIC_START, |
| .chip.name = "CIC", |
| }; |
| |
| static struct fpga_irq_data pic_irq_data = { |
| .base = INTCP_VA_PIC_BASE, |
| .irq_start = IRQ_PIC_START, |
| .chip.name = "PIC", |
| }; |
| |
| static struct fpga_irq_data sic_irq_data = { |
| .base = INTCP_VA_SIC_BASE, |
| .irq_start = IRQ_SIC_START, |
| .chip.name = "SIC", |
| }; |
| |
| static void __init intcp_init_irq(void) |
| { |
| u32 pic_mask, sic_mask; |
| |
| pic_mask = ~((~0u) << (11 - IRQ_PIC_START)); |
| pic_mask |= (~((~0u) << (29 - 22))) << 22; |
| sic_mask = ~((~0u) << (1 + IRQ_SIC_END - IRQ_SIC_START)); |
| |
| /* |
| * Disable all interrupt sources |
| */ |
| writel(0xffffffff, INTCP_VA_PIC_BASE + IRQ_ENABLE_CLEAR); |
| writel(0xffffffff, INTCP_VA_PIC_BASE + FIQ_ENABLE_CLEAR); |
| writel(0xffffffff, INTCP_VA_CIC_BASE + IRQ_ENABLE_CLEAR); |
| writel(0xffffffff, INTCP_VA_CIC_BASE + FIQ_ENABLE_CLEAR); |
| writel(sic_mask, INTCP_VA_SIC_BASE + IRQ_ENABLE_CLEAR); |
| writel(sic_mask, INTCP_VA_SIC_BASE + FIQ_ENABLE_CLEAR); |
| |
| fpga_irq_init(-1, pic_mask, &pic_irq_data); |
| |
| fpga_irq_init(-1, ~((~0u) << (1 + IRQ_CIC_END - IRQ_CIC_START)), |
| &cic_irq_data); |
| |
| fpga_irq_init(IRQ_CP_CPPLDINT, sic_mask, &sic_irq_data); |
| } |
| |
| /* |
| * Clock handling |
| */ |
| #define CM_LOCK (__io_address(INTEGRATOR_HDR_BASE)+INTEGRATOR_HDR_LOCK_OFFSET) |
| #define CM_AUXOSC (__io_address(INTEGRATOR_HDR_BASE)+0x1c) |
| |
| static const struct icst_params cp_auxvco_params = { |
| .ref = 24000000, |
| .vco_max = ICST525_VCO_MAX_5V, |
| .vco_min = ICST525_VCO_MIN, |
| .vd_min = 8, |
| .vd_max = 263, |
| .rd_min = 3, |
| .rd_max = 65, |
| .s2div = icst525_s2div, |
| .idx2s = icst525_idx2s, |
| }; |
| |
| static void cp_auxvco_set(struct clk *clk, struct icst_vco vco) |
| { |
| u32 val; |
| |
| val = readl(clk->vcoreg) & ~0x7ffff; |
| val |= vco.v | (vco.r << 9) | (vco.s << 16); |
| |
| writel(0xa05f, CM_LOCK); |
| writel(val, clk->vcoreg); |
| writel(0, CM_LOCK); |
| } |
| |
| static const struct clk_ops cp_auxclk_ops = { |
| .round = icst_clk_round, |
| .set = icst_clk_set, |
| .setvco = cp_auxvco_set, |
| }; |
| |
| static struct clk cp_auxclk = { |
| .ops = &cp_auxclk_ops, |
| .params = &cp_auxvco_params, |
| .vcoreg = CM_AUXOSC, |
| }; |
| |
| static struct clk sp804_clk = { |
| .rate = 1000000, |
| }; |
| |
| static struct clk_lookup cp_lookups[] = { |
| { /* CLCD */ |
| .dev_id = "mb:c0", |
| .clk = &cp_auxclk, |
| }, { /* SP804 timers */ |
| .dev_id = "sp804", |
| .clk = &sp804_clk, |
| }, |
| }; |
| |
| /* |
| * Flash handling. |
| */ |
| static int intcp_flash_init(struct platform_device *dev) |
| { |
| u32 val; |
| |
| val = readl(INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| val |= CINTEGRATOR_FLASHPROG_FLWREN; |
| writel(val, INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| |
| return 0; |
| } |
| |
| static void intcp_flash_exit(struct platform_device *dev) |
| { |
| u32 val; |
| |
| val = readl(INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| val &= ~(CINTEGRATOR_FLASHPROG_FLVPPEN|CINTEGRATOR_FLASHPROG_FLWREN); |
| writel(val, INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| } |
| |
| static void intcp_flash_set_vpp(struct platform_device *pdev, int on) |
| { |
| u32 val; |
| |
| val = readl(INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| if (on) |
| val |= CINTEGRATOR_FLASHPROG_FLVPPEN; |
| else |
| val &= ~CINTEGRATOR_FLASHPROG_FLVPPEN; |
| writel(val, INTCP_VA_CTRL_BASE + INTCP_FLASHPROG); |
| } |
| |
| static struct physmap_flash_data intcp_flash_data = { |
| .width = 4, |
| .init = intcp_flash_init, |
| .exit = intcp_flash_exit, |
| .set_vpp = intcp_flash_set_vpp, |
| }; |
| |
| static struct resource intcp_flash_resource = { |
| .start = INTCP_PA_FLASH_BASE, |
| .end = INTCP_PA_FLASH_BASE + INTCP_FLASH_SIZE - 1, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct platform_device intcp_flash_device = { |
| .name = "physmap-flash", |
| .id = 0, |
| .dev = { |
| .platform_data = &intcp_flash_data, |
| }, |
| .num_resources = 1, |
| .resource = &intcp_flash_resource, |
| }; |
| |
| static struct resource smc91x_resources[] = { |
| [0] = { |
| .start = INTEGRATOR_CP_ETH_BASE, |
| .end = INTEGRATOR_CP_ETH_BASE + INTCP_ETH_SIZE - 1, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = IRQ_CP_ETHINT, |
| .end = IRQ_CP_ETHINT, |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device smc91x_device = { |
| .name = "smc91x", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(smc91x_resources), |
| .resource = smc91x_resources, |
| }; |
| |
| static struct platform_device *intcp_devs[] __initdata = { |
| &intcp_flash_device, |
| &smc91x_device, |
| }; |
| |
| /* |
| * It seems that the card insertion interrupt remains active after |
| * we've acknowledged it. We therefore ignore the interrupt, and |
| * rely on reading it from the SIC. This also means that we must |
| * clear the latched interrupt. |
| */ |
| static unsigned int mmc_status(struct device *dev) |
| { |
| unsigned int status = readl(IO_ADDRESS(0xca000000 + 4)); |
| writel(8, IO_ADDRESS(INTEGRATOR_CP_CTL_BASE + 8)); |
| |
| return status & 8; |
| } |
| |
| static struct mmci_platform_data mmc_data = { |
| .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, |
| .status = mmc_status, |
| .gpio_wp = -1, |
| .gpio_cd = -1, |
| }; |
| |
| #define INTEGRATOR_CP_MMC_IRQS { IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 } |
| #define INTEGRATOR_CP_AACI_IRQS { IRQ_CP_AACIINT } |
| |
| static AMBA_APB_DEVICE(mmc, "mb:1c", 0, INTEGRATOR_CP_MMC_BASE, |
| INTEGRATOR_CP_MMC_IRQS, &mmc_data); |
| |
| static AMBA_APB_DEVICE(aaci, "mb:1d", 0, INTEGRATOR_CP_AACI_BASE, |
| INTEGRATOR_CP_AACI_IRQS, NULL); |
| |
| |
| /* |
| * CLCD support |
| */ |
| /* |
| * Ensure VGA is selected. |
| */ |
| static void cp_clcd_enable(struct clcd_fb *fb) |
| { |
| struct fb_var_screeninfo *var = &fb->fb.var; |
| u32 val = CM_CTRL_STATIC1 | CM_CTRL_STATIC2; |
| |
| if (var->bits_per_pixel <= 8 || |
| (var->bits_per_pixel == 16 && var->green.length == 5)) |
| /* Pseudocolor, RGB555, BGR555 */ |
| val |= CM_CTRL_LCDMUXSEL_VGA555_TFT555; |
| else if (fb->fb.var.bits_per_pixel <= 16) |
| /* truecolor RGB565 */ |
| val |= CM_CTRL_LCDMUXSEL_VGA565_TFT555; |
| else |
| val = 0; /* no idea for this, don't trust the docs */ |
| |
| cm_control(CM_CTRL_LCDMUXSEL_MASK| |
| CM_CTRL_LCDEN0| |
| CM_CTRL_LCDEN1| |
| CM_CTRL_STATIC1| |
| CM_CTRL_STATIC2| |
| CM_CTRL_STATIC| |
| CM_CTRL_n24BITEN, val); |
| } |
| |
| static int cp_clcd_setup(struct clcd_fb *fb) |
| { |
| fb->panel = versatile_clcd_get_panel("VGA"); |
| if (!fb->panel) |
| return -EINVAL; |
| |
| return versatile_clcd_setup_dma(fb, SZ_1M); |
| } |
| |
| static struct clcd_board clcd_data = { |
| .name = "Integrator/CP", |
| .caps = CLCD_CAP_5551 | CLCD_CAP_RGB565 | CLCD_CAP_888, |
| .check = clcdfb_check, |
| .decode = clcdfb_decode, |
| .enable = cp_clcd_enable, |
| .setup = cp_clcd_setup, |
| .mmap = versatile_clcd_mmap_dma, |
| .remove = versatile_clcd_remove_dma, |
| }; |
| |
| static AMBA_AHB_DEVICE(clcd, "mb:c0", 0, INTCP_PA_CLCD_BASE, |
| { IRQ_CP_CLCDCINT }, &clcd_data); |
| |
| static struct amba_device *amba_devs[] __initdata = { |
| &mmc_device, |
| &aaci_device, |
| &clcd_device, |
| }; |
| |
| #define REFCOUNTER (__io_address(INTEGRATOR_HDR_BASE) + 0x28) |
| |
| static void __init intcp_init_early(void) |
| { |
| clkdev_add_table(cp_lookups, ARRAY_SIZE(cp_lookups)); |
| |
| integrator_init_early(); |
| |
| #ifdef CONFIG_PLAT_VERSATILE_SCHED_CLOCK |
| versatile_sched_clock_init(REFCOUNTER, 24000000); |
| #endif |
| } |
| |
| static void __init intcp_init(void) |
| { |
| int i; |
| |
| platform_add_devices(intcp_devs, ARRAY_SIZE(intcp_devs)); |
| |
| for (i = 0; i < ARRAY_SIZE(amba_devs); i++) { |
| struct amba_device *d = amba_devs[i]; |
| amba_device_register(d, &iomem_resource); |
| } |
| } |
| |
| #define TIMER0_VA_BASE __io_address(INTEGRATOR_TIMER0_BASE) |
| #define TIMER1_VA_BASE __io_address(INTEGRATOR_TIMER1_BASE) |
| #define TIMER2_VA_BASE __io_address(INTEGRATOR_TIMER2_BASE) |
| |
| static void __init intcp_timer_init(void) |
| { |
| writel(0, TIMER0_VA_BASE + TIMER_CTRL); |
| writel(0, TIMER1_VA_BASE + TIMER_CTRL); |
| writel(0, TIMER2_VA_BASE + TIMER_CTRL); |
| |
| sp804_clocksource_init(TIMER2_VA_BASE, "timer2"); |
| sp804_clockevents_init(TIMER1_VA_BASE, IRQ_TIMERINT1, "timer1"); |
| } |
| |
| static struct sys_timer cp_timer = { |
| .init = intcp_timer_init, |
| }; |
| |
| MACHINE_START(CINTEGRATOR, "ARM-IntegratorCP") |
| /* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */ |
| .atag_offset = 0x100, |
| .reserve = integrator_reserve, |
| .map_io = intcp_map_io, |
| .nr_irqs = NR_IRQS_INTEGRATOR_CP, |
| .init_early = intcp_init_early, |
| .init_irq = intcp_init_irq, |
| .timer = &cp_timer, |
| .init_machine = intcp_init, |
| .restart = integrator_restart, |
| MACHINE_END |