| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Driver for Gigabit Ethernet adapters based on the Session Layer |
| * Interface (SLIC) technology by Alacritech. The driver does not |
| * support the hardware acceleration features provided by these cards. |
| * |
| * Copyright (C) 2016 Lino Sanfilippo <LinoSanfilippo@gmx.de> |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/if_ether.h> |
| #include <linux/crc32.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/ethtool.h> |
| #include <linux/mii.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/firmware.h> |
| #include <linux/list.h> |
| #include <linux/u64_stats_sync.h> |
| |
| #include "slic.h" |
| |
| #define DRV_NAME "slicoss" |
| |
| static const struct pci_device_id slic_id_tbl[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_ALACRITECH, |
| PCI_DEVICE_ID_ALACRITECH_MOJAVE) }, |
| { PCI_DEVICE(PCI_VENDOR_ID_ALACRITECH, |
| PCI_DEVICE_ID_ALACRITECH_OASIS) }, |
| { 0 } |
| }; |
| |
| static const char slic_stats_strings[][ETH_GSTRING_LEN] = { |
| "rx_packets", |
| "rx_bytes", |
| "rx_multicasts", |
| "rx_errors", |
| "rx_buff_miss", |
| "rx_tp_csum", |
| "rx_tp_oflow", |
| "rx_tp_hlen", |
| "rx_ip_csum", |
| "rx_ip_len", |
| "rx_ip_hdr_len", |
| "rx_early", |
| "rx_buff_oflow", |
| "rx_lcode", |
| "rx_drbl", |
| "rx_crc", |
| "rx_oflow_802", |
| "rx_uflow_802", |
| "tx_packets", |
| "tx_bytes", |
| "tx_carrier", |
| "tx_dropped", |
| "irq_errs", |
| }; |
| |
| static inline int slic_next_queue_idx(unsigned int idx, unsigned int qlen) |
| { |
| return (idx + 1) & (qlen - 1); |
| } |
| |
| static inline int slic_get_free_queue_descs(unsigned int put_idx, |
| unsigned int done_idx, |
| unsigned int qlen) |
| { |
| if (put_idx >= done_idx) |
| return (qlen - (put_idx - done_idx) - 1); |
| return (done_idx - put_idx - 1); |
| } |
| |
| static unsigned int slic_next_compl_idx(struct slic_device *sdev) |
| { |
| struct slic_stat_queue *stq = &sdev->stq; |
| unsigned int active = stq->active_array; |
| struct slic_stat_desc *descs; |
| struct slic_stat_desc *stat; |
| unsigned int idx; |
| |
| descs = stq->descs[active]; |
| stat = &descs[stq->done_idx]; |
| |
| if (!stat->status) |
| return SLIC_INVALID_STAT_DESC_IDX; |
| |
| idx = (le32_to_cpu(stat->hnd) & 0xffff) - 1; |
| /* reset desc */ |
| stat->hnd = 0; |
| stat->status = 0; |
| |
| stq->done_idx = slic_next_queue_idx(stq->done_idx, stq->len); |
| /* check for wraparound */ |
| if (!stq->done_idx) { |
| dma_addr_t paddr = stq->paddr[active]; |
| |
| slic_write(sdev, SLIC_REG_RBAR, lower_32_bits(paddr) | |
| stq->len); |
| /* make sure new status descriptors are immediately available */ |
| slic_flush_write(sdev); |
| active++; |
| active &= (SLIC_NUM_STAT_DESC_ARRAYS - 1); |
| stq->active_array = active; |
| } |
| return idx; |
| } |
| |
| static unsigned int slic_get_free_tx_descs(struct slic_tx_queue *txq) |
| { |
| /* ensure tail idx is updated */ |
| smp_mb(); |
| return slic_get_free_queue_descs(txq->put_idx, txq->done_idx, txq->len); |
| } |
| |
| static unsigned int slic_get_free_rx_descs(struct slic_rx_queue *rxq) |
| { |
| return slic_get_free_queue_descs(rxq->put_idx, rxq->done_idx, rxq->len); |
| } |
| |
| static void slic_clear_upr_list(struct slic_upr_list *upr_list) |
| { |
| struct slic_upr *upr; |
| struct slic_upr *tmp; |
| |
| spin_lock_bh(&upr_list->lock); |
| list_for_each_entry_safe(upr, tmp, &upr_list->list, list) { |
| list_del(&upr->list); |
| kfree(upr); |
| } |
| upr_list->pending = false; |
| spin_unlock_bh(&upr_list->lock); |
| } |
| |
| static void slic_start_upr(struct slic_device *sdev, struct slic_upr *upr) |
| { |
| u32 reg; |
| |
| reg = (upr->type == SLIC_UPR_CONFIG) ? SLIC_REG_RCONFIG : |
| SLIC_REG_LSTAT; |
| slic_write(sdev, reg, lower_32_bits(upr->paddr)); |
| slic_flush_write(sdev); |
| } |
| |
| static void slic_queue_upr(struct slic_device *sdev, struct slic_upr *upr) |
| { |
| struct slic_upr_list *upr_list = &sdev->upr_list; |
| bool pending; |
| |
| spin_lock_bh(&upr_list->lock); |
| pending = upr_list->pending; |
| INIT_LIST_HEAD(&upr->list); |
| list_add_tail(&upr->list, &upr_list->list); |
| upr_list->pending = true; |
| spin_unlock_bh(&upr_list->lock); |
| |
| if (!pending) |
| slic_start_upr(sdev, upr); |
| } |
| |
| static struct slic_upr *slic_dequeue_upr(struct slic_device *sdev) |
| { |
| struct slic_upr_list *upr_list = &sdev->upr_list; |
| struct slic_upr *next_upr = NULL; |
| struct slic_upr *upr = NULL; |
| |
| spin_lock_bh(&upr_list->lock); |
| if (!list_empty(&upr_list->list)) { |
| upr = list_first_entry(&upr_list->list, struct slic_upr, list); |
| list_del(&upr->list); |
| |
| if (list_empty(&upr_list->list)) |
| upr_list->pending = false; |
| else |
| next_upr = list_first_entry(&upr_list->list, |
| struct slic_upr, list); |
| } |
| spin_unlock_bh(&upr_list->lock); |
| /* trigger processing of the next upr in list */ |
| if (next_upr) |
| slic_start_upr(sdev, next_upr); |
| |
| return upr; |
| } |
| |
| static int slic_new_upr(struct slic_device *sdev, unsigned int type, |
| dma_addr_t paddr) |
| { |
| struct slic_upr *upr; |
| |
| upr = kmalloc(sizeof(*upr), GFP_ATOMIC); |
| if (!upr) |
| return -ENOMEM; |
| upr->type = type; |
| upr->paddr = paddr; |
| |
| slic_queue_upr(sdev, upr); |
| |
| return 0; |
| } |
| |
| static void slic_set_mcast_bit(u64 *mcmask, unsigned char const *addr) |
| { |
| u64 mask = *mcmask; |
| u8 crc; |
| /* Get the CRC polynomial for the mac address: we use bits 1-8 (lsb), |
| * bitwise reversed, msb (= lsb bit 0 before bitrev) is automatically |
| * discarded. |
| */ |
| crc = ether_crc(ETH_ALEN, addr) >> 23; |
| /* we only have space on the SLIC for 64 entries */ |
| crc &= 0x3F; |
| mask |= (u64)1 << crc; |
| *mcmask = mask; |
| } |
| |
| /* must be called with link_lock held */ |
| static void slic_configure_rcv(struct slic_device *sdev) |
| { |
| u32 val; |
| |
| val = SLIC_GRCR_RESET | SLIC_GRCR_ADDRAEN | SLIC_GRCR_RCVEN | |
| SLIC_GRCR_HASHSIZE << SLIC_GRCR_HASHSIZE_SHIFT | SLIC_GRCR_RCVBAD; |
| |
| if (sdev->duplex == DUPLEX_FULL) |
| val |= SLIC_GRCR_CTLEN; |
| |
| if (sdev->promisc) |
| val |= SLIC_GRCR_RCVALL; |
| |
| slic_write(sdev, SLIC_REG_WRCFG, val); |
| } |
| |
| /* must be called with link_lock held */ |
| static void slic_configure_xmt(struct slic_device *sdev) |
| { |
| u32 val; |
| |
| val = SLIC_GXCR_RESET | SLIC_GXCR_XMTEN; |
| |
| if (sdev->duplex == DUPLEX_FULL) |
| val |= SLIC_GXCR_PAUSEEN; |
| |
| slic_write(sdev, SLIC_REG_WXCFG, val); |
| } |
| |
| /* must be called with link_lock held */ |
| static void slic_configure_mac(struct slic_device *sdev) |
| { |
| u32 val; |
| |
| if (sdev->speed == SPEED_1000) { |
| val = SLIC_GMCR_GAPBB_1000 << SLIC_GMCR_GAPBB_SHIFT | |
| SLIC_GMCR_GAPR1_1000 << SLIC_GMCR_GAPR1_SHIFT | |
| SLIC_GMCR_GAPR2_1000 << SLIC_GMCR_GAPR2_SHIFT | |
| SLIC_GMCR_GBIT; /* enable GMII */ |
| } else { |
| val = SLIC_GMCR_GAPBB_100 << SLIC_GMCR_GAPBB_SHIFT | |
| SLIC_GMCR_GAPR1_100 << SLIC_GMCR_GAPR1_SHIFT | |
| SLIC_GMCR_GAPR2_100 << SLIC_GMCR_GAPR2_SHIFT; |
| } |
| |
| if (sdev->duplex == DUPLEX_FULL) |
| val |= SLIC_GMCR_FULLD; |
| |
| slic_write(sdev, SLIC_REG_WMCFG, val); |
| } |
| |
| static void slic_configure_link_locked(struct slic_device *sdev, int speed, |
| unsigned int duplex) |
| { |
| struct net_device *dev = sdev->netdev; |
| |
| if (sdev->speed == speed && sdev->duplex == duplex) |
| return; |
| |
| sdev->speed = speed; |
| sdev->duplex = duplex; |
| |
| if (sdev->speed == SPEED_UNKNOWN) { |
| if (netif_carrier_ok(dev)) |
| netif_carrier_off(dev); |
| } else { |
| /* (re)configure link settings */ |
| slic_configure_mac(sdev); |
| slic_configure_xmt(sdev); |
| slic_configure_rcv(sdev); |
| slic_flush_write(sdev); |
| |
| if (!netif_carrier_ok(dev)) |
| netif_carrier_on(dev); |
| } |
| } |
| |
| static void slic_configure_link(struct slic_device *sdev, int speed, |
| unsigned int duplex) |
| { |
| spin_lock_bh(&sdev->link_lock); |
| slic_configure_link_locked(sdev, speed, duplex); |
| spin_unlock_bh(&sdev->link_lock); |
| } |
| |
| static void slic_set_rx_mode(struct net_device *dev) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| struct netdev_hw_addr *hwaddr; |
| bool set_promisc; |
| u64 mcmask; |
| |
| if (dev->flags & (IFF_PROMISC | IFF_ALLMULTI)) { |
| /* Turn on all multicast addresses. We have to do this for |
| * promiscuous mode as well as ALLMCAST mode (it saves the |
| * microcode from having to keep state about the MAC |
| * configuration). |
| */ |
| mcmask = ~(u64)0; |
| } else { |
| mcmask = 0; |
| |
| netdev_for_each_mc_addr(hwaddr, dev) { |
| slic_set_mcast_bit(&mcmask, hwaddr->addr); |
| } |
| } |
| |
| slic_write(sdev, SLIC_REG_MCASTLOW, lower_32_bits(mcmask)); |
| slic_write(sdev, SLIC_REG_MCASTHIGH, upper_32_bits(mcmask)); |
| |
| set_promisc = !!(dev->flags & IFF_PROMISC); |
| |
| spin_lock_bh(&sdev->link_lock); |
| if (sdev->promisc != set_promisc) { |
| sdev->promisc = set_promisc; |
| slic_configure_rcv(sdev); |
| } |
| spin_unlock_bh(&sdev->link_lock); |
| } |
| |
| static void slic_xmit_complete(struct slic_device *sdev) |
| { |
| struct slic_tx_queue *txq = &sdev->txq; |
| struct net_device *dev = sdev->netdev; |
| struct slic_tx_buffer *buff; |
| unsigned int frames = 0; |
| unsigned int bytes = 0; |
| unsigned int idx; |
| |
| /* Limit processing to SLIC_MAX_TX_COMPLETIONS frames to avoid that new |
| * completions during processing keeps the loop running endlessly. |
| */ |
| do { |
| idx = slic_next_compl_idx(sdev); |
| if (idx == SLIC_INVALID_STAT_DESC_IDX) |
| break; |
| |
| txq->done_idx = idx; |
| buff = &txq->txbuffs[idx]; |
| |
| if (unlikely(!buff->skb)) { |
| netdev_warn(dev, |
| "no skb found for desc idx %i\n", idx); |
| continue; |
| } |
| dma_unmap_single(&sdev->pdev->dev, |
| dma_unmap_addr(buff, map_addr), |
| dma_unmap_len(buff, map_len), DMA_TO_DEVICE); |
| |
| bytes += buff->skb->len; |
| frames++; |
| |
| dev_kfree_skb_any(buff->skb); |
| buff->skb = NULL; |
| } while (frames < SLIC_MAX_TX_COMPLETIONS); |
| /* make sure xmit sees the new value for done_idx */ |
| smp_wmb(); |
| |
| u64_stats_update_begin(&sdev->stats.syncp); |
| sdev->stats.tx_bytes += bytes; |
| sdev->stats.tx_packets += frames; |
| u64_stats_update_end(&sdev->stats.syncp); |
| |
| netif_tx_lock(dev); |
| if (netif_queue_stopped(dev) && |
| (slic_get_free_tx_descs(txq) >= SLIC_MIN_TX_WAKEUP_DESCS)) |
| netif_wake_queue(dev); |
| netif_tx_unlock(dev); |
| } |
| |
| static void slic_refill_rx_queue(struct slic_device *sdev, gfp_t gfp) |
| { |
| const unsigned int ALIGN_MASK = SLIC_RX_BUFF_ALIGN - 1; |
| unsigned int maplen = SLIC_RX_BUFF_SIZE; |
| struct slic_rx_queue *rxq = &sdev->rxq; |
| struct net_device *dev = sdev->netdev; |
| struct slic_rx_buffer *buff; |
| struct slic_rx_desc *desc; |
| unsigned int misalign; |
| unsigned int offset; |
| struct sk_buff *skb; |
| dma_addr_t paddr; |
| |
| while (slic_get_free_rx_descs(rxq) > SLIC_MAX_REQ_RX_DESCS) { |
| skb = alloc_skb(maplen + ALIGN_MASK, gfp); |
| if (!skb) |
| break; |
| |
| paddr = dma_map_single(&sdev->pdev->dev, skb->data, maplen, |
| DMA_FROM_DEVICE); |
| if (dma_mapping_error(&sdev->pdev->dev, paddr)) { |
| netdev_err(dev, "mapping rx packet failed\n"); |
| /* drop skb */ |
| dev_kfree_skb_any(skb); |
| break; |
| } |
| /* ensure head buffer descriptors are 256 byte aligned */ |
| offset = 0; |
| misalign = paddr & ALIGN_MASK; |
| if (misalign) { |
| offset = SLIC_RX_BUFF_ALIGN - misalign; |
| skb_reserve(skb, offset); |
| } |
| /* the HW expects dma chunks for descriptor + frame data */ |
| desc = (struct slic_rx_desc *)skb->data; |
| /* temporarily sync descriptor for CPU to clear status */ |
| dma_sync_single_for_cpu(&sdev->pdev->dev, paddr, |
| offset + sizeof(*desc), |
| DMA_FROM_DEVICE); |
| desc->status = 0; |
| /* return it to HW again */ |
| dma_sync_single_for_device(&sdev->pdev->dev, paddr, |
| offset + sizeof(*desc), |
| DMA_FROM_DEVICE); |
| |
| buff = &rxq->rxbuffs[rxq->put_idx]; |
| buff->skb = skb; |
| dma_unmap_addr_set(buff, map_addr, paddr); |
| dma_unmap_len_set(buff, map_len, maplen); |
| buff->addr_offset = offset; |
| /* complete write to descriptor before it is handed to HW */ |
| wmb(); |
| /* head buffer descriptors are placed immediately before skb */ |
| slic_write(sdev, SLIC_REG_HBAR, lower_32_bits(paddr) + offset); |
| rxq->put_idx = slic_next_queue_idx(rxq->put_idx, rxq->len); |
| } |
| } |
| |
| static void slic_handle_frame_error(struct slic_device *sdev, |
| struct sk_buff *skb) |
| { |
| struct slic_stats *stats = &sdev->stats; |
| |
| if (sdev->model == SLIC_MODEL_OASIS) { |
| struct slic_rx_info_oasis *info; |
| u32 status_b; |
| u32 status; |
| |
| info = (struct slic_rx_info_oasis *)skb->data; |
| status = le32_to_cpu(info->frame_status); |
| status_b = le32_to_cpu(info->frame_status_b); |
| /* transport layer */ |
| if (status_b & SLIC_VRHSTATB_TPCSUM) |
| SLIC_INC_STATS_COUNTER(stats, rx_tpcsum); |
| if (status & SLIC_VRHSTAT_TPOFLO) |
| SLIC_INC_STATS_COUNTER(stats, rx_tpoflow); |
| if (status_b & SLIC_VRHSTATB_TPHLEN) |
| SLIC_INC_STATS_COUNTER(stats, rx_tphlen); |
| /* ip layer */ |
| if (status_b & SLIC_VRHSTATB_IPCSUM) |
| SLIC_INC_STATS_COUNTER(stats, rx_ipcsum); |
| if (status_b & SLIC_VRHSTATB_IPLERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_iplen); |
| if (status_b & SLIC_VRHSTATB_IPHERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_iphlen); |
| /* link layer */ |
| if (status_b & SLIC_VRHSTATB_RCVE) |
| SLIC_INC_STATS_COUNTER(stats, rx_early); |
| if (status_b & SLIC_VRHSTATB_BUFF) |
| SLIC_INC_STATS_COUNTER(stats, rx_buffoflow); |
| if (status_b & SLIC_VRHSTATB_CODE) |
| SLIC_INC_STATS_COUNTER(stats, rx_lcode); |
| if (status_b & SLIC_VRHSTATB_DRBL) |
| SLIC_INC_STATS_COUNTER(stats, rx_drbl); |
| if (status_b & SLIC_VRHSTATB_CRC) |
| SLIC_INC_STATS_COUNTER(stats, rx_crc); |
| if (status & SLIC_VRHSTAT_802OE) |
| SLIC_INC_STATS_COUNTER(stats, rx_oflow802); |
| if (status_b & SLIC_VRHSTATB_802UE) |
| SLIC_INC_STATS_COUNTER(stats, rx_uflow802); |
| if (status_b & SLIC_VRHSTATB_CARRE) |
| SLIC_INC_STATS_COUNTER(stats, tx_carrier); |
| } else { /* mojave */ |
| struct slic_rx_info_mojave *info; |
| u32 status; |
| |
| info = (struct slic_rx_info_mojave *)skb->data; |
| status = le32_to_cpu(info->frame_status); |
| /* transport layer */ |
| if (status & SLIC_VGBSTAT_XPERR) { |
| u32 xerr = status >> SLIC_VGBSTAT_XERRSHFT; |
| |
| if (xerr == SLIC_VGBSTAT_XCSERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_tpcsum); |
| if (xerr == SLIC_VGBSTAT_XUFLOW) |
| SLIC_INC_STATS_COUNTER(stats, rx_tpoflow); |
| if (xerr == SLIC_VGBSTAT_XHLEN) |
| SLIC_INC_STATS_COUNTER(stats, rx_tphlen); |
| } |
| /* ip layer */ |
| if (status & SLIC_VGBSTAT_NETERR) { |
| u32 nerr = status >> SLIC_VGBSTAT_NERRSHFT & |
| SLIC_VGBSTAT_NERRMSK; |
| |
| if (nerr == SLIC_VGBSTAT_NCSERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_ipcsum); |
| if (nerr == SLIC_VGBSTAT_NUFLOW) |
| SLIC_INC_STATS_COUNTER(stats, rx_iplen); |
| if (nerr == SLIC_VGBSTAT_NHLEN) |
| SLIC_INC_STATS_COUNTER(stats, rx_iphlen); |
| } |
| /* link layer */ |
| if (status & SLIC_VGBSTAT_LNKERR) { |
| u32 lerr = status & SLIC_VGBSTAT_LERRMSK; |
| |
| if (lerr == SLIC_VGBSTAT_LDEARLY) |
| SLIC_INC_STATS_COUNTER(stats, rx_early); |
| if (lerr == SLIC_VGBSTAT_LBOFLO) |
| SLIC_INC_STATS_COUNTER(stats, rx_buffoflow); |
| if (lerr == SLIC_VGBSTAT_LCODERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_lcode); |
| if (lerr == SLIC_VGBSTAT_LDBLNBL) |
| SLIC_INC_STATS_COUNTER(stats, rx_drbl); |
| if (lerr == SLIC_VGBSTAT_LCRCERR) |
| SLIC_INC_STATS_COUNTER(stats, rx_crc); |
| if (lerr == SLIC_VGBSTAT_LOFLO) |
| SLIC_INC_STATS_COUNTER(stats, rx_oflow802); |
| if (lerr == SLIC_VGBSTAT_LUFLO) |
| SLIC_INC_STATS_COUNTER(stats, rx_uflow802); |
| } |
| } |
| SLIC_INC_STATS_COUNTER(stats, rx_errors); |
| } |
| |
| static void slic_handle_receive(struct slic_device *sdev, unsigned int todo, |
| unsigned int *done) |
| { |
| struct slic_rx_queue *rxq = &sdev->rxq; |
| struct net_device *dev = sdev->netdev; |
| struct slic_rx_buffer *buff; |
| struct slic_rx_desc *desc; |
| unsigned int frames = 0; |
| unsigned int bytes = 0; |
| struct sk_buff *skb; |
| u32 status; |
| u32 len; |
| |
| while (todo && (rxq->done_idx != rxq->put_idx)) { |
| buff = &rxq->rxbuffs[rxq->done_idx]; |
| |
| skb = buff->skb; |
| if (!skb) |
| break; |
| |
| desc = (struct slic_rx_desc *)skb->data; |
| |
| dma_sync_single_for_cpu(&sdev->pdev->dev, |
| dma_unmap_addr(buff, map_addr), |
| buff->addr_offset + sizeof(*desc), |
| DMA_FROM_DEVICE); |
| |
| status = le32_to_cpu(desc->status); |
| if (!(status & SLIC_IRHDDR_SVALID)) { |
| dma_sync_single_for_device(&sdev->pdev->dev, |
| dma_unmap_addr(buff, |
| map_addr), |
| buff->addr_offset + |
| sizeof(*desc), |
| DMA_FROM_DEVICE); |
| break; |
| } |
| |
| buff->skb = NULL; |
| |
| dma_unmap_single(&sdev->pdev->dev, |
| dma_unmap_addr(buff, map_addr), |
| dma_unmap_len(buff, map_len), |
| DMA_FROM_DEVICE); |
| |
| /* skip rx descriptor that is placed before the frame data */ |
| skb_reserve(skb, SLIC_RX_BUFF_HDR_SIZE); |
| |
| if (unlikely(status & SLIC_IRHDDR_ERR)) { |
| slic_handle_frame_error(sdev, skb); |
| dev_kfree_skb_any(skb); |
| } else { |
| struct ethhdr *eh = (struct ethhdr *)skb->data; |
| |
| if (is_multicast_ether_addr(eh->h_dest)) |
| SLIC_INC_STATS_COUNTER(&sdev->stats, rx_mcasts); |
| |
| len = le32_to_cpu(desc->length) & SLIC_IRHDDR_FLEN_MSK; |
| skb_put(skb, len); |
| skb->protocol = eth_type_trans(skb, dev); |
| skb->ip_summed = CHECKSUM_UNNECESSARY; |
| |
| napi_gro_receive(&sdev->napi, skb); |
| |
| bytes += len; |
| frames++; |
| } |
| rxq->done_idx = slic_next_queue_idx(rxq->done_idx, rxq->len); |
| todo--; |
| } |
| |
| u64_stats_update_begin(&sdev->stats.syncp); |
| sdev->stats.rx_bytes += bytes; |
| sdev->stats.rx_packets += frames; |
| u64_stats_update_end(&sdev->stats.syncp); |
| |
| slic_refill_rx_queue(sdev, GFP_ATOMIC); |
| } |
| |
| static void slic_handle_link_irq(struct slic_device *sdev) |
| { |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data = sm->shmem_data; |
| unsigned int duplex; |
| int speed; |
| u32 link; |
| |
| link = le32_to_cpu(sm_data->link); |
| |
| if (link & SLIC_GIG_LINKUP) { |
| if (link & SLIC_GIG_SPEED_1000) |
| speed = SPEED_1000; |
| else if (link & SLIC_GIG_SPEED_100) |
| speed = SPEED_100; |
| else |
| speed = SPEED_10; |
| |
| duplex = (link & SLIC_GIG_FULLDUPLEX) ? DUPLEX_FULL : |
| DUPLEX_HALF; |
| } else { |
| duplex = DUPLEX_UNKNOWN; |
| speed = SPEED_UNKNOWN; |
| } |
| slic_configure_link(sdev, speed, duplex); |
| } |
| |
| static void slic_handle_upr_irq(struct slic_device *sdev, u32 irqs) |
| { |
| struct slic_upr *upr; |
| |
| /* remove upr that caused this irq (always the first entry in list) */ |
| upr = slic_dequeue_upr(sdev); |
| if (!upr) { |
| netdev_warn(sdev->netdev, "no upr found on list\n"); |
| return; |
| } |
| |
| if (upr->type == SLIC_UPR_LSTAT) { |
| if (unlikely(irqs & SLIC_ISR_UPCERR_MASK)) { |
| /* try again */ |
| slic_queue_upr(sdev, upr); |
| return; |
| } |
| slic_handle_link_irq(sdev); |
| } |
| kfree(upr); |
| } |
| |
| static int slic_handle_link_change(struct slic_device *sdev) |
| { |
| return slic_new_upr(sdev, SLIC_UPR_LSTAT, sdev->shmem.link_paddr); |
| } |
| |
| static void slic_handle_err_irq(struct slic_device *sdev, u32 isr) |
| { |
| struct slic_stats *stats = &sdev->stats; |
| |
| if (isr & SLIC_ISR_RMISS) |
| SLIC_INC_STATS_COUNTER(stats, rx_buff_miss); |
| if (isr & SLIC_ISR_XDROP) |
| SLIC_INC_STATS_COUNTER(stats, tx_dropped); |
| if (!(isr & (SLIC_ISR_RMISS | SLIC_ISR_XDROP))) |
| SLIC_INC_STATS_COUNTER(stats, irq_errs); |
| } |
| |
| static void slic_handle_irq(struct slic_device *sdev, u32 isr, |
| unsigned int todo, unsigned int *done) |
| { |
| if (isr & SLIC_ISR_ERR) |
| slic_handle_err_irq(sdev, isr); |
| |
| if (isr & SLIC_ISR_LEVENT) |
| slic_handle_link_change(sdev); |
| |
| if (isr & SLIC_ISR_UPC_MASK) |
| slic_handle_upr_irq(sdev, isr); |
| |
| if (isr & SLIC_ISR_RCV) |
| slic_handle_receive(sdev, todo, done); |
| |
| if (isr & SLIC_ISR_CMD) |
| slic_xmit_complete(sdev); |
| } |
| |
| static int slic_poll(struct napi_struct *napi, int todo) |
| { |
| struct slic_device *sdev = container_of(napi, struct slic_device, napi); |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data = sm->shmem_data; |
| u32 isr = le32_to_cpu(sm_data->isr); |
| int done = 0; |
| |
| slic_handle_irq(sdev, isr, todo, &done); |
| |
| if (done < todo) { |
| napi_complete_done(napi, done); |
| /* reenable irqs */ |
| sm_data->isr = 0; |
| /* make sure sm_data->isr is cleard before irqs are reenabled */ |
| wmb(); |
| slic_write(sdev, SLIC_REG_ISR, 0); |
| slic_flush_write(sdev); |
| } |
| |
| return done; |
| } |
| |
| static irqreturn_t slic_irq(int irq, void *dev_id) |
| { |
| struct slic_device *sdev = dev_id; |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data = sm->shmem_data; |
| |
| slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_MASK); |
| slic_flush_write(sdev); |
| /* make sure sm_data->isr is read after ICR_INT_MASK is set */ |
| wmb(); |
| |
| if (!sm_data->isr) { |
| dma_rmb(); |
| /* spurious interrupt */ |
| slic_write(sdev, SLIC_REG_ISR, 0); |
| slic_flush_write(sdev); |
| return IRQ_NONE; |
| } |
| |
| napi_schedule_irqoff(&sdev->napi); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void slic_card_reset(struct slic_device *sdev) |
| { |
| u16 cmd; |
| |
| slic_write(sdev, SLIC_REG_RESET, SLIC_RESET_MAGIC); |
| /* flush write by means of config space */ |
| pci_read_config_word(sdev->pdev, PCI_COMMAND, &cmd); |
| mdelay(1); |
| } |
| |
| static int slic_init_stat_queue(struct slic_device *sdev) |
| { |
| const unsigned int DESC_ALIGN_MASK = SLIC_STATS_DESC_ALIGN - 1; |
| struct slic_stat_queue *stq = &sdev->stq; |
| struct slic_stat_desc *descs; |
| unsigned int misalign; |
| unsigned int offset; |
| dma_addr_t paddr; |
| size_t size; |
| int err; |
| int i; |
| |
| stq->len = SLIC_NUM_STAT_DESCS; |
| stq->active_array = 0; |
| stq->done_idx = 0; |
| |
| size = stq->len * sizeof(*descs) + DESC_ALIGN_MASK; |
| |
| for (i = 0; i < SLIC_NUM_STAT_DESC_ARRAYS; i++) { |
| descs = dma_alloc_coherent(&sdev->pdev->dev, size, &paddr, |
| GFP_KERNEL); |
| if (!descs) { |
| netdev_err(sdev->netdev, |
| "failed to allocate status descriptors\n"); |
| err = -ENOMEM; |
| goto free_descs; |
| } |
| /* ensure correct alignment */ |
| offset = 0; |
| misalign = paddr & DESC_ALIGN_MASK; |
| if (misalign) { |
| offset = SLIC_STATS_DESC_ALIGN - misalign; |
| descs += offset; |
| paddr += offset; |
| } |
| |
| slic_write(sdev, SLIC_REG_RBAR, lower_32_bits(paddr) | |
| stq->len); |
| stq->descs[i] = descs; |
| stq->paddr[i] = paddr; |
| stq->addr_offset[i] = offset; |
| } |
| |
| stq->mem_size = size; |
| |
| return 0; |
| |
| free_descs: |
| while (i--) { |
| dma_free_coherent(&sdev->pdev->dev, stq->mem_size, |
| stq->descs[i] - stq->addr_offset[i], |
| stq->paddr[i] - stq->addr_offset[i]); |
| } |
| |
| return err; |
| } |
| |
| static void slic_free_stat_queue(struct slic_device *sdev) |
| { |
| struct slic_stat_queue *stq = &sdev->stq; |
| int i; |
| |
| for (i = 0; i < SLIC_NUM_STAT_DESC_ARRAYS; i++) { |
| dma_free_coherent(&sdev->pdev->dev, stq->mem_size, |
| stq->descs[i] - stq->addr_offset[i], |
| stq->paddr[i] - stq->addr_offset[i]); |
| } |
| } |
| |
| static int slic_init_tx_queue(struct slic_device *sdev) |
| { |
| struct slic_tx_queue *txq = &sdev->txq; |
| struct slic_tx_buffer *buff; |
| struct slic_tx_desc *desc; |
| unsigned int i; |
| int err; |
| |
| txq->len = SLIC_NUM_TX_DESCS; |
| txq->put_idx = 0; |
| txq->done_idx = 0; |
| |
| txq->txbuffs = kcalloc(txq->len, sizeof(*buff), GFP_KERNEL); |
| if (!txq->txbuffs) |
| return -ENOMEM; |
| |
| txq->dma_pool = dma_pool_create("slic_pool", &sdev->pdev->dev, |
| sizeof(*desc), SLIC_TX_DESC_ALIGN, |
| 4096); |
| if (!txq->dma_pool) { |
| err = -ENOMEM; |
| netdev_err(sdev->netdev, "failed to create dma pool\n"); |
| goto free_buffs; |
| } |
| |
| for (i = 0; i < txq->len; i++) { |
| buff = &txq->txbuffs[i]; |
| desc = dma_pool_zalloc(txq->dma_pool, GFP_KERNEL, |
| &buff->desc_paddr); |
| if (!desc) { |
| netdev_err(sdev->netdev, |
| "failed to alloc pool chunk (%i)\n", i); |
| err = -ENOMEM; |
| goto free_descs; |
| } |
| |
| desc->hnd = cpu_to_le32((u32)(i + 1)); |
| desc->cmd = SLIC_CMD_XMT_REQ; |
| desc->flags = 0; |
| desc->type = cpu_to_le32(SLIC_CMD_TYPE_DUMB); |
| buff->desc = desc; |
| } |
| |
| return 0; |
| |
| free_descs: |
| while (i--) { |
| buff = &txq->txbuffs[i]; |
| dma_pool_free(txq->dma_pool, buff->desc, buff->desc_paddr); |
| } |
| dma_pool_destroy(txq->dma_pool); |
| |
| free_buffs: |
| kfree(txq->txbuffs); |
| |
| return err; |
| } |
| |
| static void slic_free_tx_queue(struct slic_device *sdev) |
| { |
| struct slic_tx_queue *txq = &sdev->txq; |
| struct slic_tx_buffer *buff; |
| unsigned int i; |
| |
| for (i = 0; i < txq->len; i++) { |
| buff = &txq->txbuffs[i]; |
| dma_pool_free(txq->dma_pool, buff->desc, buff->desc_paddr); |
| if (!buff->skb) |
| continue; |
| |
| dma_unmap_single(&sdev->pdev->dev, |
| dma_unmap_addr(buff, map_addr), |
| dma_unmap_len(buff, map_len), DMA_TO_DEVICE); |
| consume_skb(buff->skb); |
| } |
| dma_pool_destroy(txq->dma_pool); |
| |
| kfree(txq->txbuffs); |
| } |
| |
| static int slic_init_rx_queue(struct slic_device *sdev) |
| { |
| struct slic_rx_queue *rxq = &sdev->rxq; |
| struct slic_rx_buffer *buff; |
| |
| rxq->len = SLIC_NUM_RX_LES; |
| rxq->done_idx = 0; |
| rxq->put_idx = 0; |
| |
| buff = kcalloc(rxq->len, sizeof(*buff), GFP_KERNEL); |
| if (!buff) |
| return -ENOMEM; |
| |
| rxq->rxbuffs = buff; |
| slic_refill_rx_queue(sdev, GFP_KERNEL); |
| |
| return 0; |
| } |
| |
| static void slic_free_rx_queue(struct slic_device *sdev) |
| { |
| struct slic_rx_queue *rxq = &sdev->rxq; |
| struct slic_rx_buffer *buff; |
| unsigned int i; |
| |
| /* free rx buffers */ |
| for (i = 0; i < rxq->len; i++) { |
| buff = &rxq->rxbuffs[i]; |
| |
| if (!buff->skb) |
| continue; |
| |
| dma_unmap_single(&sdev->pdev->dev, |
| dma_unmap_addr(buff, map_addr), |
| dma_unmap_len(buff, map_len), |
| DMA_FROM_DEVICE); |
| consume_skb(buff->skb); |
| } |
| kfree(rxq->rxbuffs); |
| } |
| |
| static void slic_set_link_autoneg(struct slic_device *sdev) |
| { |
| unsigned int subid = sdev->pdev->subsystem_device; |
| u32 val; |
| |
| if (sdev->is_fiber) { |
| /* We've got a fiber gigabit interface, and register 4 is |
| * different in fiber mode than in copper mode. |
| */ |
| /* advertise FD only @1000 Mb */ |
| val = MII_ADVERTISE << 16 | ADVERTISE_1000XFULL | |
| ADVERTISE_1000XPAUSE | ADVERTISE_1000XPSE_ASYM; |
| /* enable PAUSE frames */ |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| /* reset phy, enable auto-neg */ |
| val = MII_BMCR << 16 | BMCR_RESET | BMCR_ANENABLE | |
| BMCR_ANRESTART; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| } else { /* copper gigabit */ |
| /* We've got a copper gigabit interface, and register 4 is |
| * different in copper mode than in fiber mode. |
| */ |
| /* advertise 10/100 Mb modes */ |
| val = MII_ADVERTISE << 16 | ADVERTISE_100FULL | |
| ADVERTISE_100HALF | ADVERTISE_10FULL | ADVERTISE_10HALF; |
| /* enable PAUSE frames */ |
| val |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM; |
| /* required by the Cicada PHY */ |
| val |= ADVERTISE_CSMA; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| |
| /* advertise FD only @1000 Mb */ |
| val = MII_CTRL1000 << 16 | ADVERTISE_1000FULL; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| |
| if (subid != PCI_SUBDEVICE_ID_ALACRITECH_CICADA) { |
| /* if a Marvell PHY enable auto crossover */ |
| val = SLIC_MIICR_REG_16 | SLIC_MRV_REG16_XOVERON; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| |
| /* reset phy, enable auto-neg */ |
| val = MII_BMCR << 16 | BMCR_RESET | BMCR_ANENABLE | |
| BMCR_ANRESTART; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| } else { |
| /* enable and restart auto-neg (don't reset) */ |
| val = MII_BMCR << 16 | BMCR_ANENABLE | BMCR_ANRESTART; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| } |
| } |
| } |
| |
| static void slic_set_mac_address(struct slic_device *sdev) |
| { |
| const u8 *addr = sdev->netdev->dev_addr; |
| u32 val; |
| |
| val = addr[5] | addr[4] << 8 | addr[3] << 16 | addr[2] << 24; |
| |
| slic_write(sdev, SLIC_REG_WRADDRAL, val); |
| slic_write(sdev, SLIC_REG_WRADDRBL, val); |
| |
| val = addr[0] << 8 | addr[1]; |
| |
| slic_write(sdev, SLIC_REG_WRADDRAH, val); |
| slic_write(sdev, SLIC_REG_WRADDRBH, val); |
| slic_flush_write(sdev); |
| } |
| |
| static u32 slic_read_dword_from_firmware(const struct firmware *fw, int *offset) |
| { |
| int idx = *offset; |
| __le32 val; |
| |
| memcpy(&val, fw->data + *offset, sizeof(val)); |
| idx += 4; |
| *offset = idx; |
| |
| return le32_to_cpu(val); |
| } |
| |
| MODULE_FIRMWARE(SLIC_RCV_FIRMWARE_MOJAVE); |
| MODULE_FIRMWARE(SLIC_RCV_FIRMWARE_OASIS); |
| |
| static int slic_load_rcvseq_firmware(struct slic_device *sdev) |
| { |
| const struct firmware *fw; |
| const char *file; |
| u32 codelen; |
| int idx = 0; |
| u32 instr; |
| u32 addr; |
| int err; |
| |
| file = (sdev->model == SLIC_MODEL_OASIS) ? SLIC_RCV_FIRMWARE_OASIS : |
| SLIC_RCV_FIRMWARE_MOJAVE; |
| err = request_firmware(&fw, file, &sdev->pdev->dev); |
| if (err) { |
| dev_err(&sdev->pdev->dev, |
| "failed to load receive sequencer firmware %s\n", file); |
| return err; |
| } |
| /* Do an initial sanity check concerning firmware size now. A further |
| * check follows below. |
| */ |
| if (fw->size < SLIC_FIRMWARE_MIN_SIZE) { |
| dev_err(&sdev->pdev->dev, |
| "invalid firmware size %zu (min %u expected)\n", |
| fw->size, SLIC_FIRMWARE_MIN_SIZE); |
| err = -EINVAL; |
| goto release; |
| } |
| |
| codelen = slic_read_dword_from_firmware(fw, &idx); |
| |
| /* do another sanity check against firmware size */ |
| if ((codelen + 4) > fw->size) { |
| dev_err(&sdev->pdev->dev, |
| "invalid rcv-sequencer firmware size %zu\n", fw->size); |
| err = -EINVAL; |
| goto release; |
| } |
| |
| /* download sequencer code to card */ |
| slic_write(sdev, SLIC_REG_RCV_WCS, SLIC_RCVWCS_BEGIN); |
| for (addr = 0; addr < codelen; addr++) { |
| __le32 val; |
| /* write out instruction address */ |
| slic_write(sdev, SLIC_REG_RCV_WCS, addr); |
| |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| /* write out the instruction data low addr */ |
| slic_write(sdev, SLIC_REG_RCV_WCS, instr); |
| |
| val = (__le32)fw->data[idx]; |
| instr = le32_to_cpu(val); |
| idx++; |
| /* write out the instruction data high addr */ |
| slic_write(sdev, SLIC_REG_RCV_WCS, instr); |
| } |
| /* finish download */ |
| slic_write(sdev, SLIC_REG_RCV_WCS, SLIC_RCVWCS_FINISH); |
| slic_flush_write(sdev); |
| release: |
| release_firmware(fw); |
| |
| return err; |
| } |
| |
| MODULE_FIRMWARE(SLIC_FIRMWARE_MOJAVE); |
| MODULE_FIRMWARE(SLIC_FIRMWARE_OASIS); |
| |
| static int slic_load_firmware(struct slic_device *sdev) |
| { |
| u32 sectstart[SLIC_FIRMWARE_MAX_SECTIONS]; |
| u32 sectsize[SLIC_FIRMWARE_MAX_SECTIONS]; |
| const struct firmware *fw; |
| unsigned int datalen; |
| const char *file; |
| int code_start; |
| unsigned int i; |
| u32 numsects; |
| int idx = 0; |
| u32 sect; |
| u32 instr; |
| u32 addr; |
| u32 base; |
| int err; |
| |
| file = (sdev->model == SLIC_MODEL_OASIS) ? SLIC_FIRMWARE_OASIS : |
| SLIC_FIRMWARE_MOJAVE; |
| err = request_firmware(&fw, file, &sdev->pdev->dev); |
| if (err) { |
| dev_err(&sdev->pdev->dev, "failed to load firmware %s\n", file); |
| return err; |
| } |
| /* Do an initial sanity check concerning firmware size now. A further |
| * check follows below. |
| */ |
| if (fw->size < SLIC_FIRMWARE_MIN_SIZE) { |
| dev_err(&sdev->pdev->dev, |
| "invalid firmware size %zu (min is %u)\n", fw->size, |
| SLIC_FIRMWARE_MIN_SIZE); |
| err = -EINVAL; |
| goto release; |
| } |
| |
| numsects = slic_read_dword_from_firmware(fw, &idx); |
| if (numsects == 0 || numsects > SLIC_FIRMWARE_MAX_SECTIONS) { |
| dev_err(&sdev->pdev->dev, |
| "invalid number of sections in firmware: %u", numsects); |
| err = -EINVAL; |
| goto release; |
| } |
| |
| datalen = numsects * 8 + 4; |
| for (i = 0; i < numsects; i++) { |
| sectsize[i] = slic_read_dword_from_firmware(fw, &idx); |
| datalen += sectsize[i]; |
| } |
| |
| /* do another sanity check against firmware size */ |
| if (datalen > fw->size) { |
| dev_err(&sdev->pdev->dev, |
| "invalid firmware size %zu (expected >= %u)\n", |
| fw->size, datalen); |
| err = -EINVAL; |
| goto release; |
| } |
| /* get sections */ |
| for (i = 0; i < numsects; i++) |
| sectstart[i] = slic_read_dword_from_firmware(fw, &idx); |
| |
| code_start = idx; |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| |
| for (sect = 0; sect < numsects; sect++) { |
| unsigned int ssize = sectsize[sect] >> 3; |
| |
| base = sectstart[sect]; |
| |
| for (addr = 0; addr < ssize; addr++) { |
| /* write out instruction address */ |
| slic_write(sdev, SLIC_REG_WCS, base + addr); |
| /* write out instruction to low addr */ |
| slic_write(sdev, SLIC_REG_WCS, instr); |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| /* write out instruction to high addr */ |
| slic_write(sdev, SLIC_REG_WCS, instr); |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| } |
| } |
| |
| idx = code_start; |
| |
| for (sect = 0; sect < numsects; sect++) { |
| unsigned int ssize = sectsize[sect] >> 3; |
| |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| base = sectstart[sect]; |
| if (base < 0x8000) |
| continue; |
| |
| for (addr = 0; addr < ssize; addr++) { |
| /* write out instruction address */ |
| slic_write(sdev, SLIC_REG_WCS, |
| SLIC_WCS_COMPARE | (base + addr)); |
| /* write out instruction to low addr */ |
| slic_write(sdev, SLIC_REG_WCS, instr); |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| /* write out instruction to high addr */ |
| slic_write(sdev, SLIC_REG_WCS, instr); |
| instr = slic_read_dword_from_firmware(fw, &idx); |
| } |
| } |
| slic_flush_write(sdev); |
| mdelay(10); |
| /* everything OK, kick off the card */ |
| slic_write(sdev, SLIC_REG_WCS, SLIC_WCS_START); |
| slic_flush_write(sdev); |
| /* wait long enough for ucode to init card and reach the mainloop */ |
| mdelay(20); |
| release: |
| release_firmware(fw); |
| |
| return err; |
| } |
| |
| static int slic_init_shmem(struct slic_device *sdev) |
| { |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data; |
| dma_addr_t paddr; |
| |
| sm_data = dma_alloc_coherent(&sdev->pdev->dev, sizeof(*sm_data), |
| &paddr, GFP_KERNEL); |
| if (!sm_data) { |
| dev_err(&sdev->pdev->dev, "failed to allocate shared memory\n"); |
| return -ENOMEM; |
| } |
| |
| sm->shmem_data = sm_data; |
| sm->isr_paddr = paddr; |
| sm->link_paddr = paddr + offsetof(struct slic_shmem_data, link); |
| |
| return 0; |
| } |
| |
| static void slic_free_shmem(struct slic_device *sdev) |
| { |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data = sm->shmem_data; |
| |
| dma_free_coherent(&sdev->pdev->dev, sizeof(*sm_data), sm_data, |
| sm->isr_paddr); |
| } |
| |
| static int slic_init_iface(struct slic_device *sdev) |
| { |
| struct slic_shmem *sm = &sdev->shmem; |
| int err; |
| |
| sdev->upr_list.pending = false; |
| |
| err = slic_init_shmem(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to init shared memory\n"); |
| return err; |
| } |
| |
| err = slic_load_firmware(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to load firmware\n"); |
| goto free_sm; |
| } |
| |
| err = slic_load_rcvseq_firmware(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, |
| "failed to load firmware for receive sequencer\n"); |
| goto free_sm; |
| } |
| |
| slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_OFF); |
| slic_flush_write(sdev); |
| mdelay(1); |
| |
| err = slic_init_rx_queue(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to init rx queue: %u\n", err); |
| goto free_sm; |
| } |
| |
| err = slic_init_tx_queue(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to init tx queue: %u\n", err); |
| goto free_rxq; |
| } |
| |
| err = slic_init_stat_queue(sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to init status queue: %u\n", |
| err); |
| goto free_txq; |
| } |
| |
| slic_write(sdev, SLIC_REG_ISP, lower_32_bits(sm->isr_paddr)); |
| napi_enable(&sdev->napi); |
| /* disable irq mitigation */ |
| slic_write(sdev, SLIC_REG_INTAGG, 0); |
| slic_write(sdev, SLIC_REG_ISR, 0); |
| slic_flush_write(sdev); |
| |
| slic_set_mac_address(sdev); |
| |
| spin_lock_bh(&sdev->link_lock); |
| sdev->duplex = DUPLEX_UNKNOWN; |
| sdev->speed = SPEED_UNKNOWN; |
| spin_unlock_bh(&sdev->link_lock); |
| |
| slic_set_link_autoneg(sdev); |
| |
| err = request_irq(sdev->pdev->irq, slic_irq, IRQF_SHARED, DRV_NAME, |
| sdev); |
| if (err) { |
| netdev_err(sdev->netdev, "failed to request irq: %u\n", err); |
| goto disable_napi; |
| } |
| |
| slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_ON); |
| slic_flush_write(sdev); |
| /* request initial link status */ |
| err = slic_handle_link_change(sdev); |
| if (err) |
| netdev_warn(sdev->netdev, |
| "failed to set initial link state: %u\n", err); |
| return 0; |
| |
| disable_napi: |
| napi_disable(&sdev->napi); |
| slic_free_stat_queue(sdev); |
| free_txq: |
| slic_free_tx_queue(sdev); |
| free_rxq: |
| slic_free_rx_queue(sdev); |
| free_sm: |
| slic_free_shmem(sdev); |
| slic_card_reset(sdev); |
| |
| return err; |
| } |
| |
| static int slic_open(struct net_device *dev) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| int err; |
| |
| netif_carrier_off(dev); |
| |
| err = slic_init_iface(sdev); |
| if (err) { |
| netdev_err(dev, "failed to initialize interface: %i\n", err); |
| return err; |
| } |
| |
| netif_start_queue(dev); |
| |
| return 0; |
| } |
| |
| static int slic_close(struct net_device *dev) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| u32 val; |
| |
| netif_stop_queue(dev); |
| |
| /* stop irq handling */ |
| napi_disable(&sdev->napi); |
| slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_OFF); |
| slic_write(sdev, SLIC_REG_ISR, 0); |
| slic_flush_write(sdev); |
| |
| free_irq(sdev->pdev->irq, sdev); |
| /* turn off RCV and XMT and power down PHY */ |
| val = SLIC_GXCR_RESET | SLIC_GXCR_PAUSEEN; |
| slic_write(sdev, SLIC_REG_WXCFG, val); |
| |
| val = SLIC_GRCR_RESET | SLIC_GRCR_CTLEN | SLIC_GRCR_ADDRAEN | |
| SLIC_GRCR_HASHSIZE << SLIC_GRCR_HASHSIZE_SHIFT; |
| slic_write(sdev, SLIC_REG_WRCFG, val); |
| |
| val = MII_BMCR << 16 | BMCR_PDOWN; |
| slic_write(sdev, SLIC_REG_WPHY, val); |
| slic_flush_write(sdev); |
| |
| slic_clear_upr_list(&sdev->upr_list); |
| slic_write(sdev, SLIC_REG_QUIESCE, 0); |
| |
| slic_free_stat_queue(sdev); |
| slic_free_tx_queue(sdev); |
| slic_free_rx_queue(sdev); |
| slic_free_shmem(sdev); |
| |
| slic_card_reset(sdev); |
| netif_carrier_off(dev); |
| |
| return 0; |
| } |
| |
| static netdev_tx_t slic_xmit(struct sk_buff *skb, struct net_device *dev) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| struct slic_tx_queue *txq = &sdev->txq; |
| struct slic_tx_buffer *buff; |
| struct slic_tx_desc *desc; |
| dma_addr_t paddr; |
| u32 cbar_val; |
| u32 maplen; |
| |
| if (unlikely(slic_get_free_tx_descs(txq) < SLIC_MAX_REQ_TX_DESCS)) { |
| netdev_err(dev, "BUG! not enough tx LEs left: %u\n", |
| slic_get_free_tx_descs(txq)); |
| return NETDEV_TX_BUSY; |
| } |
| |
| maplen = skb_headlen(skb); |
| paddr = dma_map_single(&sdev->pdev->dev, skb->data, maplen, |
| DMA_TO_DEVICE); |
| if (dma_mapping_error(&sdev->pdev->dev, paddr)) { |
| netdev_err(dev, "failed to map tx buffer\n"); |
| goto drop_skb; |
| } |
| |
| buff = &txq->txbuffs[txq->put_idx]; |
| buff->skb = skb; |
| dma_unmap_addr_set(buff, map_addr, paddr); |
| dma_unmap_len_set(buff, map_len, maplen); |
| |
| desc = buff->desc; |
| desc->totlen = cpu_to_le32(maplen); |
| desc->paddrl = cpu_to_le32(lower_32_bits(paddr)); |
| desc->paddrh = cpu_to_le32(upper_32_bits(paddr)); |
| desc->len = cpu_to_le32(maplen); |
| |
| txq->put_idx = slic_next_queue_idx(txq->put_idx, txq->len); |
| |
| cbar_val = lower_32_bits(buff->desc_paddr) | 1; |
| /* complete writes to RAM and DMA before hardware is informed */ |
| wmb(); |
| |
| slic_write(sdev, SLIC_REG_CBAR, cbar_val); |
| |
| if (slic_get_free_tx_descs(txq) < SLIC_MAX_REQ_TX_DESCS) |
| netif_stop_queue(dev); |
| |
| return NETDEV_TX_OK; |
| drop_skb: |
| dev_kfree_skb_any(skb); |
| |
| return NETDEV_TX_OK; |
| } |
| |
| static void slic_get_stats(struct net_device *dev, |
| struct rtnl_link_stats64 *lst) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| struct slic_stats *stats = &sdev->stats; |
| |
| SLIC_GET_STATS_COUNTER(lst->rx_packets, stats, rx_packets); |
| SLIC_GET_STATS_COUNTER(lst->tx_packets, stats, tx_packets); |
| SLIC_GET_STATS_COUNTER(lst->rx_bytes, stats, rx_bytes); |
| SLIC_GET_STATS_COUNTER(lst->tx_bytes, stats, tx_bytes); |
| SLIC_GET_STATS_COUNTER(lst->rx_errors, stats, rx_errors); |
| SLIC_GET_STATS_COUNTER(lst->rx_dropped, stats, rx_buff_miss); |
| SLIC_GET_STATS_COUNTER(lst->tx_dropped, stats, tx_dropped); |
| SLIC_GET_STATS_COUNTER(lst->multicast, stats, rx_mcasts); |
| SLIC_GET_STATS_COUNTER(lst->rx_over_errors, stats, rx_buffoflow); |
| SLIC_GET_STATS_COUNTER(lst->rx_crc_errors, stats, rx_crc); |
| SLIC_GET_STATS_COUNTER(lst->rx_fifo_errors, stats, rx_oflow802); |
| SLIC_GET_STATS_COUNTER(lst->tx_carrier_errors, stats, tx_carrier); |
| } |
| |
| static int slic_get_sset_count(struct net_device *dev, int sset) |
| { |
| switch (sset) { |
| case ETH_SS_STATS: |
| return ARRAY_SIZE(slic_stats_strings); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static void slic_get_ethtool_stats(struct net_device *dev, |
| struct ethtool_stats *eth_stats, u64 *data) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| struct slic_stats *stats = &sdev->stats; |
| |
| SLIC_GET_STATS_COUNTER(data[0], stats, rx_packets); |
| SLIC_GET_STATS_COUNTER(data[1], stats, rx_bytes); |
| SLIC_GET_STATS_COUNTER(data[2], stats, rx_mcasts); |
| SLIC_GET_STATS_COUNTER(data[3], stats, rx_errors); |
| SLIC_GET_STATS_COUNTER(data[4], stats, rx_buff_miss); |
| SLIC_GET_STATS_COUNTER(data[5], stats, rx_tpcsum); |
| SLIC_GET_STATS_COUNTER(data[6], stats, rx_tpoflow); |
| SLIC_GET_STATS_COUNTER(data[7], stats, rx_tphlen); |
| SLIC_GET_STATS_COUNTER(data[8], stats, rx_ipcsum); |
| SLIC_GET_STATS_COUNTER(data[9], stats, rx_iplen); |
| SLIC_GET_STATS_COUNTER(data[10], stats, rx_iphlen); |
| SLIC_GET_STATS_COUNTER(data[11], stats, rx_early); |
| SLIC_GET_STATS_COUNTER(data[12], stats, rx_buffoflow); |
| SLIC_GET_STATS_COUNTER(data[13], stats, rx_lcode); |
| SLIC_GET_STATS_COUNTER(data[14], stats, rx_drbl); |
| SLIC_GET_STATS_COUNTER(data[15], stats, rx_crc); |
| SLIC_GET_STATS_COUNTER(data[16], stats, rx_oflow802); |
| SLIC_GET_STATS_COUNTER(data[17], stats, rx_uflow802); |
| SLIC_GET_STATS_COUNTER(data[18], stats, tx_packets); |
| SLIC_GET_STATS_COUNTER(data[19], stats, tx_bytes); |
| SLIC_GET_STATS_COUNTER(data[20], stats, tx_carrier); |
| SLIC_GET_STATS_COUNTER(data[21], stats, tx_dropped); |
| SLIC_GET_STATS_COUNTER(data[22], stats, irq_errs); |
| } |
| |
| static void slic_get_strings(struct net_device *dev, u32 stringset, u8 *data) |
| { |
| if (stringset == ETH_SS_STATS) |
| memcpy(data, slic_stats_strings, sizeof(slic_stats_strings)); |
| } |
| |
| static void slic_get_drvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| struct slic_device *sdev = netdev_priv(dev); |
| |
| strscpy(info->driver, DRV_NAME, sizeof(info->driver)); |
| strscpy(info->bus_info, pci_name(sdev->pdev), sizeof(info->bus_info)); |
| } |
| |
| static const struct ethtool_ops slic_ethtool_ops = { |
| .get_drvinfo = slic_get_drvinfo, |
| .get_link = ethtool_op_get_link, |
| .get_strings = slic_get_strings, |
| .get_ethtool_stats = slic_get_ethtool_stats, |
| .get_sset_count = slic_get_sset_count, |
| }; |
| |
| static const struct net_device_ops slic_netdev_ops = { |
| .ndo_open = slic_open, |
| .ndo_stop = slic_close, |
| .ndo_start_xmit = slic_xmit, |
| .ndo_set_mac_address = eth_mac_addr, |
| .ndo_get_stats64 = slic_get_stats, |
| .ndo_set_rx_mode = slic_set_rx_mode, |
| .ndo_validate_addr = eth_validate_addr, |
| }; |
| |
| static u16 slic_eeprom_csum(unsigned char *eeprom, unsigned int len) |
| { |
| unsigned char *ptr = eeprom; |
| u32 csum = 0; |
| __le16 data; |
| |
| while (len > 1) { |
| memcpy(&data, ptr, sizeof(data)); |
| csum += le16_to_cpu(data); |
| ptr += 2; |
| len -= 2; |
| } |
| if (len > 0) |
| csum += *(u8 *)ptr; |
| while (csum >> 16) |
| csum = (csum & 0xFFFF) + ((csum >> 16) & 0xFFFF); |
| return ~csum; |
| } |
| |
| /* check eeprom size, magic and checksum */ |
| static bool slic_eeprom_valid(unsigned char *eeprom, unsigned int size) |
| { |
| const unsigned int MAX_SIZE = 128; |
| const unsigned int MIN_SIZE = 98; |
| __le16 magic; |
| __le16 csum; |
| |
| if (size < MIN_SIZE || size > MAX_SIZE) |
| return false; |
| memcpy(&magic, eeprom, sizeof(magic)); |
| if (le16_to_cpu(magic) != SLIC_EEPROM_MAGIC) |
| return false; |
| /* cut checksum bytes */ |
| size -= 2; |
| memcpy(&csum, eeprom + size, sizeof(csum)); |
| |
| return (le16_to_cpu(csum) == slic_eeprom_csum(eeprom, size)); |
| } |
| |
| static int slic_read_eeprom(struct slic_device *sdev) |
| { |
| unsigned int devfn = PCI_FUNC(sdev->pdev->devfn); |
| struct slic_shmem *sm = &sdev->shmem; |
| struct slic_shmem_data *sm_data = sm->shmem_data; |
| const unsigned int MAX_LOOPS = 5000; |
| unsigned int codesize; |
| unsigned char *eeprom; |
| struct slic_upr *upr; |
| unsigned int i = 0; |
| dma_addr_t paddr; |
| int err = 0; |
| u8 *mac[2]; |
| |
| eeprom = dma_alloc_coherent(&sdev->pdev->dev, SLIC_EEPROM_SIZE, |
| &paddr, GFP_KERNEL); |
| if (!eeprom) |
| return -ENOMEM; |
| |
| slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_OFF); |
| /* setup ISP temporarily */ |
| slic_write(sdev, SLIC_REG_ISP, lower_32_bits(sm->isr_paddr)); |
| |
| err = slic_new_upr(sdev, SLIC_UPR_CONFIG, paddr); |
| if (!err) { |
| for (i = 0; i < MAX_LOOPS; i++) { |
| if (le32_to_cpu(sm_data->isr) & SLIC_ISR_UPC) |
| break; |
| mdelay(1); |
| } |
| if (i == MAX_LOOPS) { |
| dev_err(&sdev->pdev->dev, |
| "timed out while waiting for eeprom data\n"); |
| err = -ETIMEDOUT; |
| } |
| upr = slic_dequeue_upr(sdev); |
| kfree(upr); |
| } |
| |
| slic_write(sdev, SLIC_REG_ISP, 0); |
| slic_write(sdev, SLIC_REG_ISR, 0); |
| slic_flush_write(sdev); |
| |
| if (err) |
| goto free_eeprom; |
| |
| if (sdev->model == SLIC_MODEL_OASIS) { |
| struct slic_oasis_eeprom *oee; |
| |
| oee = (struct slic_oasis_eeprom *)eeprom; |
| mac[0] = oee->mac; |
| mac[1] = oee->mac2; |
| codesize = le16_to_cpu(oee->eeprom_code_size); |
| } else { |
| struct slic_mojave_eeprom *mee; |
| |
| mee = (struct slic_mojave_eeprom *)eeprom; |
| mac[0] = mee->mac; |
| mac[1] = mee->mac2; |
| codesize = le16_to_cpu(mee->eeprom_code_size); |
| } |
| |
| if (!slic_eeprom_valid(eeprom, codesize)) { |
| dev_err(&sdev->pdev->dev, "invalid checksum in eeprom\n"); |
| err = -EINVAL; |
| goto free_eeprom; |
| } |
| /* set mac address */ |
| eth_hw_addr_set(sdev->netdev, mac[devfn]); |
| free_eeprom: |
| dma_free_coherent(&sdev->pdev->dev, SLIC_EEPROM_SIZE, eeprom, paddr); |
| |
| return err; |
| } |
| |
| static int slic_init(struct slic_device *sdev) |
| { |
| int err; |
| |
| spin_lock_init(&sdev->upper_lock); |
| spin_lock_init(&sdev->link_lock); |
| INIT_LIST_HEAD(&sdev->upr_list.list); |
| spin_lock_init(&sdev->upr_list.lock); |
| u64_stats_init(&sdev->stats.syncp); |
| |
| slic_card_reset(sdev); |
| |
| err = slic_load_firmware(sdev); |
| if (err) { |
| dev_err(&sdev->pdev->dev, "failed to load firmware\n"); |
| return err; |
| } |
| |
| /* we need the shared memory to read EEPROM so set it up temporarily */ |
| err = slic_init_shmem(sdev); |
| if (err) { |
| dev_err(&sdev->pdev->dev, "failed to init shared memory\n"); |
| return err; |
| } |
| |
| err = slic_read_eeprom(sdev); |
| if (err) { |
| dev_err(&sdev->pdev->dev, "failed to read eeprom\n"); |
| goto free_sm; |
| } |
| |
| slic_card_reset(sdev); |
| slic_free_shmem(sdev); |
| |
| return 0; |
| free_sm: |
| slic_free_shmem(sdev); |
| |
| return err; |
| } |
| |
| static bool slic_is_fiber(unsigned short subdev) |
| { |
| switch (subdev) { |
| /* Mojave */ |
| case PCI_SUBDEVICE_ID_ALACRITECH_1000X1F: |
| case PCI_SUBDEVICE_ID_ALACRITECH_SES1001F: fallthrough; |
| /* Oasis */ |
| case PCI_SUBDEVICE_ID_ALACRITECH_SEN2002XF: |
| case PCI_SUBDEVICE_ID_ALACRITECH_SEN2001XF: |
| case PCI_SUBDEVICE_ID_ALACRITECH_SEN2104EF: |
| case PCI_SUBDEVICE_ID_ALACRITECH_SEN2102EF: |
| return true; |
| } |
| return false; |
| } |
| |
| static void slic_configure_pci(struct pci_dev *pdev) |
| { |
| u16 old; |
| u16 cmd; |
| |
| pci_read_config_word(pdev, PCI_COMMAND, &old); |
| |
| cmd = old | PCI_COMMAND_PARITY | PCI_COMMAND_SERR; |
| if (old != cmd) |
| pci_write_config_word(pdev, PCI_COMMAND, cmd); |
| } |
| |
| static int slic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) |
| { |
| struct slic_device *sdev; |
| struct net_device *dev; |
| int err; |
| |
| err = pci_enable_device(pdev); |
| if (err) { |
| dev_err(&pdev->dev, "failed to enable PCI device\n"); |
| return err; |
| } |
| |
| pci_set_master(pdev); |
| pci_try_set_mwi(pdev); |
| |
| slic_configure_pci(pdev); |
| |
| err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); |
| if (err) { |
| dev_err(&pdev->dev, "failed to setup DMA\n"); |
| goto disable; |
| } |
| |
| dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); |
| |
| err = pci_request_regions(pdev, DRV_NAME); |
| if (err) { |
| dev_err(&pdev->dev, "failed to obtain PCI regions\n"); |
| goto disable; |
| } |
| |
| dev = alloc_etherdev(sizeof(*sdev)); |
| if (!dev) { |
| dev_err(&pdev->dev, "failed to alloc ethernet device\n"); |
| err = -ENOMEM; |
| goto free_regions; |
| } |
| |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| pci_set_drvdata(pdev, dev); |
| dev->irq = pdev->irq; |
| dev->netdev_ops = &slic_netdev_ops; |
| dev->hw_features = NETIF_F_RXCSUM; |
| dev->features |= dev->hw_features; |
| |
| dev->ethtool_ops = &slic_ethtool_ops; |
| |
| sdev = netdev_priv(dev); |
| sdev->model = (pdev->device == PCI_DEVICE_ID_ALACRITECH_OASIS) ? |
| SLIC_MODEL_OASIS : SLIC_MODEL_MOJAVE; |
| sdev->is_fiber = slic_is_fiber(pdev->subsystem_device); |
| sdev->pdev = pdev; |
| sdev->netdev = dev; |
| sdev->regs = ioremap(pci_resource_start(pdev, 0), |
| pci_resource_len(pdev, 0)); |
| if (!sdev->regs) { |
| dev_err(&pdev->dev, "failed to map registers\n"); |
| err = -ENOMEM; |
| goto free_netdev; |
| } |
| |
| err = slic_init(sdev); |
| if (err) { |
| dev_err(&pdev->dev, "failed to initialize driver\n"); |
| goto unmap; |
| } |
| |
| netif_napi_add(dev, &sdev->napi, slic_poll); |
| netif_carrier_off(dev); |
| |
| err = register_netdev(dev); |
| if (err) { |
| dev_err(&pdev->dev, "failed to register net device: %i\n", err); |
| goto unmap; |
| } |
| |
| return 0; |
| |
| unmap: |
| iounmap(sdev->regs); |
| free_netdev: |
| free_netdev(dev); |
| free_regions: |
| pci_release_regions(pdev); |
| disable: |
| pci_disable_device(pdev); |
| |
| return err; |
| } |
| |
| static void slic_remove(struct pci_dev *pdev) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| struct slic_device *sdev = netdev_priv(dev); |
| |
| unregister_netdev(dev); |
| iounmap(sdev->regs); |
| free_netdev(dev); |
| pci_release_regions(pdev); |
| pci_disable_device(pdev); |
| } |
| |
| static struct pci_driver slic_driver = { |
| .name = DRV_NAME, |
| .id_table = slic_id_tbl, |
| .probe = slic_probe, |
| .remove = slic_remove, |
| }; |
| |
| module_pci_driver(slic_driver); |
| |
| MODULE_DESCRIPTION("Alacritech non-accelerated SLIC driver"); |
| MODULE_AUTHOR("Lino Sanfilippo <LinoSanfilippo@gmx.de>"); |
| MODULE_LICENSE("GPL"); |