| // SPDX-License-Identifier: BSD-3-Clause |
| /* Copyright (c) 2022, The Linux Foundation. All rights reserved. */ |
| |
| #include <dt-bindings/clock/qcom,gcc-msm8953.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/soc/qcom,apr.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| chosen { }; |
| |
| clocks { |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <19200000>; |
| clock-output-names = "xo"; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x1>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x2>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x3>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU4: cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x100>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU5: cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x101>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU6: cpu@102 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x102>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU7: cpu@103 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x103>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&L2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| }; |
| |
| cluster1 { |
| core0 { |
| cpu = <&CPU4>; |
| }; |
| core1 { |
| cpu = <&CPU5>; |
| }; |
| core2 { |
| cpu = <&CPU6>; |
| }; |
| core3 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| }; |
| |
| L2_0: l2-cache-0 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| |
| L2_1: l2-cache-1 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm-msm8953", "qcom,scm"; |
| clocks = <&gcc GCC_CRYPTO_CLK>, |
| <&gcc GCC_CRYPTO_AXI_CLK>, |
| <&gcc GCC_CRYPTO_AHB_CLK>; |
| clock-names = "core", "bus", "iface"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| memory@10000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the reg */ |
| reg = <0 0x10000000 0 0>; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a53-pmu"; |
| interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| rpm: remoteproc { |
| compatible = "qcom,msm8953-rpm-proc", "qcom,rpm-proc"; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; |
| qcom,ipc = <&apcs 8 0>; |
| qcom,smd-edge = <15>; |
| |
| rpm_requests: rpm-requests { |
| compatible = "qcom,rpm-msm8953"; |
| qcom,smd-channels = "rpm_requests"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-msm8953", "qcom,rpmcc"; |
| clocks = <&xo_board>; |
| clock-names = "xo"; |
| #clock-cells = <1>; |
| }; |
| |
| rpmpd: power-controller { |
| compatible = "qcom,msm8953-rpmpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmpd_opp_table>; |
| |
| rpmpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmpd_opp_ret: opp1 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION>; |
| }; |
| |
| rpmpd_opp_ret_plus: opp2 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; |
| }; |
| |
| rpmpd_opp_min_svs: opp3 { |
| opp-level = <RPM_SMD_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmpd_opp_low_svs: opp4 { |
| opp-level = <RPM_SMD_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmpd_opp_svs: opp5 { |
| opp-level = <RPM_SMD_LEVEL_SVS>; |
| }; |
| |
| rpmpd_opp_svs_plus: opp6 { |
| opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; |
| }; |
| |
| rpmpd_opp_nom: opp7 { |
| opp-level = <RPM_SMD_LEVEL_NOM>; |
| }; |
| |
| rpmpd_opp_nom_plus: opp8 { |
| opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; |
| }; |
| |
| rpmpd_opp_turbo: opp9 { |
| opp-level = <RPM_SMD_LEVEL_TURBO>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| zap_shader_region: zap@81800000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0x81800000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| qseecom_mem: qseecom@85b00000 { |
| reg = <0x0 0x85b00000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| smem_mem: smem@86300000 { |
| compatible = "qcom,smem"; |
| reg = <0x0 0x86300000 0x0 0x100000>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| hwlocks = <&tcsr_mutex 3>; |
| no-map; |
| }; |
| |
| reserved@86400000 { |
| reg = <0x0 0x86400000 0x0 0x400000>; |
| no-map; |
| }; |
| |
| mpss_mem: mpss@86c00000 { |
| reg = <0x0 0x86c00000 0x0 0x6a00000>; |
| no-map; |
| }; |
| |
| adsp_fw_mem: adsp@8d600000 { |
| reg = <0x0 0x8d600000 0x0 0x1100000>; |
| no-map; |
| }; |
| |
| wcnss_fw_mem: wcnss@8e700000 { |
| reg = <0x0 0x8e700000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| dfps_data_mem: dfps-data@90000000 { |
| reg = <0 0x90000000 0 0x1000>; |
| no-map; |
| }; |
| |
| cont_splash_mem: cont-splash@90001000 { |
| reg = <0x0 0x90001000 0x0 0x13ff000>; |
| no-map; |
| }; |
| |
| venus_mem: venus@91400000 { |
| reg = <0x0 0x91400000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| mba_mem: mba@92000000 { |
| reg = <0x0 0x92000000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| rmtfs@f2d00000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0x0 0xf2d00000 0x0 0x180000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| }; |
| }; |
| |
| smp2p-adsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| |
| interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs 10>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| smp2p_adsp_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_adsp_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-modem { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| |
| interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>; |
| |
| qcom,ipc = <&apcs 8 14>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| smp2p_modem_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_modem_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-wcnss { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <451>, <431>; |
| |
| interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>; |
| |
| qcom,ipc = <&apcs 8 18>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <4>; |
| |
| smp2p_wcnss_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_wcnss_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smsm { |
| compatible = "qcom,smsm"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| qcom,ipc-1 = <&apcs 8 13>; |
| qcom,ipc-3 = <&apcs 8 19>; |
| |
| apps_smsm: apps@0 { |
| reg = <0>; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smsm: modem@1 { |
| reg = <1>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| wcnss_smsm: wcnss@6 { |
| reg = <6>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0xffffffff>; |
| compatible = "simple-bus"; |
| |
| rpm_msg_ram: sram@60000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0x00060000 0x8000>; |
| }; |
| |
| hsusb_phy: phy@79000 { |
| compatible = "qcom,msm8953-qusb2-phy"; |
| reg = <0x00079000 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB_CLK>, |
| <&gcc GCC_QUSB_REF_CLK>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| qcom,tcsr-syscon = <&tcsr_phy_clk_scheme_sel>; |
| |
| resets = <&gcc GCC_QUSB2_PHY_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| rng@e3000 { |
| compatible = "qcom,prng"; |
| reg = <0x000e3000 0x1000>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| tsens0: thermal-sensor@4a9000 { |
| compatible = "qcom,msm8953-tsens", "qcom,tsens-v2"; |
| reg = <0x004a9000 0x1000>, /* TM */ |
| <0x004a8000 0x1000>; /* SROT */ |
| #qcom,sensors = <16>; |
| interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| restart@4ab000 { |
| compatible = "qcom,pshold"; |
| reg = <0x004ab000 0x4>; |
| }; |
| |
| tlmm: pinctrl@1000000 { |
| compatible = "qcom,msm8953-pinctrl"; |
| reg = <0x01000000 0x300000>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| gpio-ranges = <&tlmm 0 0 142>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| uart_console_active: uart-console-active-state { |
| pins = "gpio4", "gpio5"; |
| function = "blsp_uart2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| uart_console_sleep: uart-console-sleep-state { |
| pins = "gpio4", "gpio5"; |
| function = "blsp_uart2"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| sdc1_clk_on: sdc1-clk-on-state { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| sdc1_clk_off: sdc1-clk-off-state { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| sdc1_cmd_on: sdc1-cmd-on-state { |
| pins = "sdc1_cmd"; |
| bias-disable; |
| drive-strength = <10>; |
| }; |
| |
| sdc1_cmd_off: sdc1-cmd-off-state { |
| pins = "sdc1_cmd"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| sdc1_data_on: sdc1-data-on-state { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| sdc1_data_off: sdc1-data-off-state { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sdc1_rclk_on: sdc1-rclk-on-state { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| |
| sdc1_rclk_off: sdc1-rclk-off-state { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| |
| sdc2_clk_on: sdc2-clk-on-state { |
| pins = "sdc2_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| sdc2_clk_off: sdc2-clk-off-state { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| sdc2_cmd_on: sdc2-cmd-on-state { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| sdc2_cmd_off: sdc2-cmd-off-state { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sdc2_data_on: sdc2-data-on-state { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| sdc2_data_off: sdc2-data-off-state { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sdc2_cd_on: cd-on-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| sdc2_cd_off: cd-off-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_key_default: gpio-key-default-state { |
| pins = "gpio85"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c_1_default: i2c-1-default-state { |
| pins = "gpio2", "gpio3"; |
| function = "blsp_i2c1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_1_sleep: i2c-1-sleep-state { |
| pins = "gpio2", "gpio3"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_2_default: i2c-2-default-state { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_2_sleep: i2c-2-sleep-state { |
| pins = "gpio6", "gpio7"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_3_default: i2c-3-default-state { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_i2c3"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_3_sleep: i2c-3-sleep-state { |
| pins = "gpio10", "gpio11"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_4_default: i2c-4-default-state { |
| pins = "gpio14", "gpio15"; |
| function = "blsp_i2c4"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_4_sleep: i2c-4-sleep-state { |
| pins = "gpio14", "gpio15"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_5_default: i2c-5-default-state { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_i2c5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_5_sleep: i2c-5-sleep-state { |
| pins = "gpio18", "gpio19"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_6_default: i2c-6-default-state { |
| pins = "gpio22", "gpio23"; |
| function = "blsp_i2c6"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_6_sleep: i2c-6-sleep-state { |
| pins = "gpio22", "gpio23"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_7_default: i2c-7-default-state { |
| pins = "gpio135", "gpio136"; |
| function = "blsp_i2c7"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_7_sleep: i2c-7-sleep-state { |
| pins = "gpio135", "gpio136"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_8_default: i2c-8-default-state { |
| pins = "gpio98", "gpio99"; |
| function = "blsp_i2c8"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c_8_sleep: i2c-8-sleep-state { |
| pins = "gpio98", "gpio99"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_3_default: spi-3-default-state { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_spi3"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_3_sleep: spi-3-sleep-state { |
| pins = "gpio10", "gpio11"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_5_default: spi-5-default-state { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_spi5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_5_sleep: spi-5-sleep-state { |
| pins = "gpio18", "gpio19"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_6_default: spi-6-default-state { |
| pins = "gpio22", "gpio23"; |
| function = "blsp_spi6"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| spi_6_sleep: spi-6-sleep-state { |
| pins = "gpio22", "gpio23"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wcnss_pin_a: wcnss-active-state { |
| |
| wcss-wlan2-pins { |
| pins = "gpio76"; |
| function = "wcss_wlan2"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan1-pins { |
| pins = "gpio77"; |
| function = "wcss_wlan1"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan0-pins { |
| pins = "gpio78"; |
| function = "wcss_wlan0"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan-pins { |
| pins = "gpio79", "gpio80"; |
| function = "wcss_wlan"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| gcc: clock-controller@1800000 { |
| compatible = "qcom,gcc-msm8953"; |
| reg = <0x01800000 0x80000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&sleep_clk>, |
| <&mdss_dsi0_phy 1>, |
| <&mdss_dsi0_phy 0>, |
| <&mdss_dsi1_phy 1>, |
| <&mdss_dsi1_phy 0>; |
| clock-names = "xo", |
| "sleep", |
| "dsi0pll", |
| "dsi0pllbyte", |
| "dsi1pll", |
| "dsi1pllbyte"; |
| }; |
| |
| tcsr_mutex: hwlock@1905000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0x01905000 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr: syscon@1937000 { |
| compatible = "qcom,tcsr-msm8953", "syscon"; |
| reg = <0x01937000 0x30000>; |
| }; |
| |
| tcsr_phy_clk_scheme_sel: syscon@193f044 { |
| compatible = "qcom,tcsr-msm8953", "syscon"; |
| reg = <0x0193f044 0x4>; |
| }; |
| |
| mdss: display-subsystem@1a00000 { |
| compatible = "qcom,mdss"; |
| |
| reg = <0x01a00000 0x1000>, |
| <0x01ab0000 0x1040>; |
| reg-names = "mdss_phys", |
| "vbif_phys"; |
| |
| power-domains = <&gcc MDSS_GDSC>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_VSYNC_CLK>, |
| <&gcc GCC_MDSS_MDP_CLK>; |
| clock-names = "iface", |
| "bus", |
| "vsync", |
| "core"; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| status = "disabled"; |
| |
| mdp: display-controller@1a01000 { |
| compatible = "qcom,msm8953-mdp5", "qcom,mdp5"; |
| reg = <0x01a01000 0x89000>; |
| reg-names = "mdp_phys"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <0>; |
| |
| power-domains = <&gcc MDSS_GDSC>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_VSYNC_CLK>; |
| clock-names = "iface", |
| "bus", |
| "core", |
| "vsync"; |
| |
| iommus = <&apps_iommu 0x15>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdp5_intf1_out: endpoint { |
| remote-endpoint = <&mdss_dsi0_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdp5_intf2_out: endpoint { |
| remote-endpoint = <&mdss_dsi1_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0: dsi@1a94000 { |
| compatible = "qcom,msm8953-dsi-ctrl", "qcom,mdss-dsi-ctrl"; |
| reg = <0x01a94000 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <4>; |
| |
| assigned-clocks = <&gcc BYTE0_CLK_SRC>, |
| <&gcc PCLK0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi0_phy 0>, |
| <&mdss_dsi0_phy 1>; |
| |
| clocks = <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_BYTE0_CLK>, |
| <&gcc GCC_MDSS_PCLK0_CLK>, |
| <&gcc GCC_MDSS_ESC0_CLK>; |
| clock-names = "mdp_core", |
| "iface", |
| "bus", |
| "byte", |
| "pixel", |
| "core"; |
| |
| phys = <&mdss_dsi0_phy>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi0_in: endpoint { |
| remote-endpoint = <&mdp5_intf1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0_phy: phy@1a94400 { |
| compatible = "qcom,dsi-phy-14nm-8953"; |
| reg = <0x01a94400 0x100>, |
| <0x01a94500 0x300>, |
| <0x01a94800 0x188>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| |
| mdss_dsi1: dsi@1a96000 { |
| compatible = "qcom,msm8953-dsi-ctrl", "qcom,mdss-dsi-ctrl"; |
| reg = <0x01a96000 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <5>; |
| |
| assigned-clocks = <&gcc BYTE1_CLK_SRC>, |
| <&gcc PCLK1_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi1_phy 0>, |
| <&mdss_dsi1_phy 1>; |
| |
| clocks = <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_BYTE1_CLK>, |
| <&gcc GCC_MDSS_PCLK1_CLK>, |
| <&gcc GCC_MDSS_ESC1_CLK>; |
| clock-names = "mdp_core", |
| "iface", |
| "bus", |
| "byte", |
| "pixel", |
| "core"; |
| |
| phys = <&mdss_dsi1_phy>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi1_in: endpoint { |
| remote-endpoint = <&mdp5_intf2_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi1_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi1_phy: phy@1a96400 { |
| compatible = "qcom,dsi-phy-14nm-8953"; |
| reg = <0x01a96400 0x100>, |
| <0x01a96500 0x300>, |
| <0x01a96800 0x188>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| apps_iommu: iommu@1e20000 { |
| compatible = "qcom,msm8953-iommu", "qcom,msm-iommu-v1"; |
| ranges = <0 0x01e20000 0x20000>; |
| |
| clocks = <&gcc GCC_SMMU_CFG_CLK>, |
| <&gcc GCC_APSS_TCU_ASYNC_CLK>; |
| clock-names = "iface", "bus"; |
| |
| qcom,iommu-secure-id = <17>; |
| |
| #address-cells = <1>; |
| #iommu-cells = <1>; |
| #size-cells = <1>; |
| |
| /* VFE */ |
| iommu-ctx@14000 { |
| compatible = "qcom,msm-iommu-v1-ns"; |
| reg = <0x14000 0x1000>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* MDP_0 */ |
| iommu-ctx@15000 { |
| compatible = "qcom,msm-iommu-v1-ns"; |
| reg = <0x15000 0x1000>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* VENUS_NS */ |
| iommu-ctx@16000 { |
| compatible = "qcom,msm-iommu-v1-ns"; |
| reg = <0x16000 0x1000>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| spmi_bus: spmi@200f000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0200f000 0x1000>, |
| <0x02400000 0x800000>, |
| <0x02c00000 0x800000>, |
| <0x03800000 0x200000>, |
| <0x0200a000 0x2100>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| interrupt-controller; |
| |
| #interrupt-cells = <4>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| }; |
| |
| mpss: remoteproc@4080000 { |
| compatible = "qcom,msm8953-mss-pil"; |
| reg = <0x04080000 0x100>, |
| <0x04020000 0x040>; |
| reg-names = "qdsp6", "rmb"; |
| |
| interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| power-domains = <&rpmpd MSM8953_VDDCX>, |
| <&rpmpd MSM8953_VDDMX>, |
| <&rpmpd MSM8953_VDDMD>; |
| power-domain-names = "cx", "mx","mss"; |
| |
| clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, |
| <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, |
| <&gcc GCC_BOOT_ROM_AHB_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "bus", "mem", "xo"; |
| |
| qcom,smem-states = <&smp2p_modem_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| resets = <&gcc GCC_MSS_BCR>; |
| reset-names = "mss_restart"; |
| |
| qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>; |
| |
| status = "disabled"; |
| |
| mba { |
| memory-region = <&mba_mem>; |
| }; |
| |
| mpss { |
| memory-region = <&mpss_mem>; |
| }; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>; |
| |
| qcom,smd-edge = <0>; |
| qcom,ipc = <&apcs 8 12>; |
| qcom,remote-pid = <1>; |
| |
| label = "modem"; |
| }; |
| }; |
| |
| usb3: usb@70f8800 { |
| compatible = "qcom,msm8953-dwc3", "qcom,dwc3"; |
| reg = <0x070f8800 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hs_phy_irq", "ss_phy_irq"; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB_CLK>, |
| <&gcc GCC_USB30_MASTER_CLK>, |
| <&gcc GCC_PCNOC_USB3_AXI_CLK>, |
| <&gcc GCC_USB30_SLEEP_CLK>, |
| <&gcc GCC_USB30_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <133330000>; |
| |
| power-domains = <&gcc USB30_GDSC>; |
| |
| qcom,select-utmi-as-pipe-clk; |
| |
| status = "disabled"; |
| |
| usb3_dwc3: usb@7000000 { |
| compatible = "snps,dwc3"; |
| reg = <0x07000000 0xcc00>; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&hsusb_phy>; |
| phy-names = "usb2-phy"; |
| |
| snps,usb2-gadget-lpm-disable; |
| snps,dis-u1-entry-quirk; |
| snps,dis-u2-entry-quirk; |
| snps,is-utmi-l1-suspend; |
| snps,hird-threshold = /bits/ 8 <0x00>; |
| |
| maximum-speed = "high-speed"; |
| }; |
| }; |
| |
| sdhc_1: mmc@7824900 { |
| compatible = "qcom,msm8953-sdhci", "qcom,sdhci-msm-v4"; |
| |
| reg = <0x07824900 0x500>, <0x07824000 0x800>; |
| reg-names = "hc", "core"; |
| |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC1_AHB_CLK>, |
| <&gcc GCC_SDCC1_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| |
| power-domains = <&rpmpd MSM8953_VDDCX>; |
| operating-points-v2 = <&sdhc1_opp_table>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>; |
| |
| mmc-hs400-1_8v; |
| mmc-hs200-1_8v; |
| mmc-ddr-1_8v; |
| bus-width = <8>; |
| non-removable; |
| |
| status = "disabled"; |
| |
| sdhc1_opp_table: opp-table-sdhc1 { |
| compatible = "operating-points-v2"; |
| |
| opp-25000000 { |
| opp-hz = /bits/ 64 <25000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-192000000 { |
| opp-hz = /bits/ 64 <192000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| |
| opp-384000000 { |
| opp-hz = /bits/ 64 <384000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| sdhc_2: mmc@7864900 { |
| compatible = "qcom,msm8953-sdhci", "qcom,sdhci-msm-v4"; |
| |
| reg = <0x07864900 0x500>, <0x07864000 0x800>; |
| reg-names = "hc", "core"; |
| |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC2_AHB_CLK>, |
| <&gcc GCC_SDCC2_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| |
| power-domains = <&rpmpd MSM8953_VDDCX>; |
| operating-points-v2 = <&sdhc2_opp_table>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; |
| |
| bus-width = <4>; |
| |
| status = "disabled"; |
| |
| sdhc2_opp_table: opp-table-sdhc2 { |
| compatible = "operating-points-v2"; |
| |
| opp-25000000 { |
| opp-hz = /bits/ 64 <25000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-177770000 { |
| opp-hz = /bits/ 64 <177770000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| blsp1_dma: dma-controller@7884000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x07884000 0x1f000>; |
| interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "bam_clk"; |
| num-channels = <12>; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| qcom,num-ees = <4>; |
| qcom,controlled-remotely; |
| }; |
| |
| uart_0: serial@78af000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x078af000 0x200>; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_1: i2c@78b5000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b5000 0x600>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| dmas = <&blsp1_dma 4>, <&blsp1_dma 5>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_1_default>; |
| pinctrl-1 = <&i2c_1_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_2: i2c@78b6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b6000 0x600>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_2_default>; |
| pinctrl-1 = <&i2c_2_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_3: i2c@78b7000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b7000 0x600>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_3_default>; |
| pinctrl-1 = <&i2c_3_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi_3: spi@78b7000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| reg = <0x078b7000 0x600>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&spi_3_default>; |
| pinctrl-1 = <&spi_3_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_4: i2c@78b8000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b8000 0x600>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_4_default>; |
| pinctrl-1 = <&i2c_4_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| blsp2_dma: dma-controller@7ac4000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x07ac4000 0x1f000>; |
| interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "bam_clk"; |
| num-channels = <12>; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| qcom,num-ees = <4>; |
| qcom,controlled-remotely; |
| }; |
| |
| i2c_5: i2c@7af5000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af5000 0x600>; |
| interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 4>, <&blsp2_dma 5>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_5_default>; |
| pinctrl-1 = <&i2c_5_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi_5: spi@7af5000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| reg = <0x07af5000 0x600>; |
| interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 4>, <&blsp2_dma 5>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&spi_5_default>; |
| pinctrl-1 = <&spi_5_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_6: i2c@7af6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af6000 0x600>; |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_6_default>; |
| pinctrl-1 = <&i2c_6_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi_6: spi@7af6000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| reg = <0x07af6000 0x600>; |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&spi_6_default>; |
| pinctrl-1 = <&spi_6_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_7: i2c@7af7000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af7000 0x600>; |
| interrupts = <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_7_default>; |
| pinctrl-1 = <&i2c_7_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c_8: i2c@7af8000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af8000 0x600>; |
| interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "core", "iface"; |
| clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c_8_default>; |
| pinctrl-1 = <&i2c_8_sleep>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| wcnss: remoteproc@a204000 { |
| compatible = "qcom,pronto-v3-pil", "qcom,pronto"; |
| reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>; |
| reg-names = "ccu", "dxe", "pmu"; |
| |
| memory-region = <&wcnss_fw_mem>; |
| |
| interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_wcnss_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_wcnss_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_wcnss_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_wcnss_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; |
| |
| power-domains = <&rpmpd MSM8953_VDDCX>, |
| <&rpmpd MSM8953_VDDMX>; |
| power-domain-names = "cx", "mx"; |
| |
| qcom,smem-states = <&smp2p_wcnss_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcnss_pin_a>; |
| |
| status = "disabled"; |
| |
| wcnss_iris: iris { |
| /* Separate chip, compatible is board-specific */ |
| clocks = <&rpmcc RPM_SMD_RF_CLK2>; |
| clock-names = "xo"; |
| }; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>; |
| |
| qcom,ipc = <&apcs 8 17>; |
| qcom,smd-edge = <6>; |
| qcom,remote-pid = <4>; |
| |
| label = "pronto"; |
| |
| wcnss_ctrl: wcnss { |
| compatible = "qcom,wcnss"; |
| qcom,smd-channels = "WCNSS_CTRL"; |
| |
| qcom,mmio = <&wcnss>; |
| |
| wcnss_bt: bluetooth { |
| compatible = "qcom,wcnss-bt"; |
| }; |
| |
| wcnss_wifi: wifi { |
| compatible = "qcom,wcnss-wlan"; |
| |
| interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "tx", "rx"; |
| |
| qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; |
| qcom,smem-state-names = "tx-enable", |
| "tx-rings-empty"; |
| }; |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@b000000 { |
| compatible = "qcom,msm-qgic2"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>; |
| }; |
| |
| apcs: mailbox@b011000 { |
| compatible = "qcom,msm8953-apcs-kpss-global", "syscon"; |
| reg = <0x0b011000 0x1000>; |
| #mbox-cells = <1>; |
| }; |
| |
| timer@b120000 { |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0b120000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| frame@b121000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b121000 0x1000>, |
| <0x0b122000 0x1000>; |
| }; |
| |
| frame@b123000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b123000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b124000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b124000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b125000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b125000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b126000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b126000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b127000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b127000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b128000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b128000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lpass: remoteproc@c200000 { |
| compatible = "qcom,msm8953-adsp-pil"; |
| reg = <0x0c200000 0x100>; |
| |
| interrupts-extended = <&intc 0 293 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "xo"; |
| |
| power-domains = <&rpmpd MSM8953_VDDCX>; |
| power-domain-names = "cx"; |
| |
| memory-region = <&adsp_fw_mem>; |
| |
| qcom,smem-states = <&smp2p_adsp_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>; |
| |
| label = "lpass"; |
| mboxes = <&apcs 8>; |
| qcom,smd-edge = <1>; |
| qcom,remote-pid = <2>; |
| |
| apr { |
| compatible = "qcom,apr-v2"; |
| qcom,smd-channels = "apr_audio_svc"; |
| qcom,domain = <APR_DOMAIN_ADSP>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| q6core: service@3 { |
| reg = <APR_SVC_ADSP_CORE>; |
| compatible = "qcom,q6core"; |
| }; |
| |
| q6afe: service@4 { |
| compatible = "qcom,q6afe"; |
| reg = <APR_SVC_AFE>; |
| q6afedai: dais { |
| compatible = "qcom,q6afe-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| |
| dai@16 { |
| reg = <PRIMARY_MI2S_RX>; |
| qcom,sd-lines = <0 1>; |
| }; |
| dai@20 { |
| reg = <TERTIARY_MI2S_TX>; |
| qcom,sd-lines = <0 1>; |
| }; |
| dai@127 { |
| reg = <QUINARY_MI2S_RX>; |
| qcom,sd-lines = <0>; |
| }; |
| }; |
| |
| q6afecc: clock-controller { |
| compatible = "qcom,q6afe-clocks"; |
| #clock-cells = <2>; |
| }; |
| }; |
| |
| q6asm: service@7 { |
| compatible = "qcom,q6asm"; |
| reg = <APR_SVC_ASM>; |
| q6asmdai: dais { |
| compatible = "qcom,q6asm-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| |
| dai@0 { |
| reg = <0>; |
| direction = <Q6ASM_DAI_RX>; |
| }; |
| dai@1 { |
| reg = <1>; |
| direction = <Q6ASM_DAI_TX>; |
| }; |
| dai@2 { |
| reg = <2>; |
| direction = <Q6ASM_DAI_RX>; |
| }; |
| dai@3 { |
| reg = <3>; |
| direction = <Q6ASM_DAI_RX>; |
| is-compress-dai; |
| }; |
| }; |
| }; |
| |
| q6adm: service@8 { |
| compatible = "qcom,q6adm"; |
| reg = <APR_SVC_ADM>; |
| q6routing: routing { |
| compatible = "qcom,q6adm-routing"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 9>; |
| trips { |
| cpu0_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu0_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu0_alert>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 10>; |
| trips { |
| cpu1_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu1_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu1_alert>; |
| cooling-device = <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 11>; |
| trips { |
| cpu2_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu2_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu2_alert>; |
| cooling-device = <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 12>; |
| trips { |
| cpu3_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu3_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu3_alert>; |
| cooling-device = <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu4-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 4>; |
| trips { |
| cpu4_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu4_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu4_alert>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu5-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 5>; |
| trips { |
| cpu5_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu5_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu5_alert>; |
| cooling-device = <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu6-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 6>; |
| trips { |
| cpu6_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu6_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu6_alert>; |
| cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| cpu7-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| thermal-sensors = <&tsens0 7>; |
| trips { |
| cpu7_alert: trip-point0 { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu7_crit: crit { |
| temperature = <100000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| cooling-maps { |
| map0 { |
| trip = <&cpu7_alert>; |
| cooling-device = <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| }; |
