| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2019, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include <video/mipi_display.h> |
| |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_modes.h> |
| #include <drm/drm_panel.h> |
| |
| struct visionox_rm69299 { |
| struct drm_panel panel; |
| struct regulator_bulk_data supplies[2]; |
| struct gpio_desc *reset_gpio; |
| struct mipi_dsi_device *dsi; |
| bool prepared; |
| bool enabled; |
| }; |
| |
| static inline struct visionox_rm69299 *panel_to_ctx(struct drm_panel *panel) |
| { |
| return container_of(panel, struct visionox_rm69299, panel); |
| } |
| |
| static int visionox_rm69299_power_on(struct visionox_rm69299 *ctx) |
| { |
| int ret; |
| |
| ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Reset sequence of visionox panel requires the panel to be |
| * out of reset for 10ms, followed by being held in reset |
| * for 10ms and then out again |
| */ |
| gpiod_set_value(ctx->reset_gpio, 1); |
| usleep_range(10000, 20000); |
| gpiod_set_value(ctx->reset_gpio, 0); |
| usleep_range(10000, 20000); |
| gpiod_set_value(ctx->reset_gpio, 1); |
| usleep_range(10000, 20000); |
| |
| return 0; |
| } |
| |
| static int visionox_rm69299_power_off(struct visionox_rm69299 *ctx) |
| { |
| gpiod_set_value(ctx->reset_gpio, 0); |
| |
| return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); |
| } |
| |
| static int visionox_rm69299_unprepare(struct drm_panel *panel) |
| { |
| struct visionox_rm69299 *ctx = panel_to_ctx(panel); |
| int ret; |
| |
| ctx->dsi->mode_flags = 0; |
| |
| ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_OFF, NULL, 0); |
| if (ret < 0) |
| dev_err(ctx->panel.dev, "set_display_off cmd failed ret = %d\n", ret); |
| |
| /* 120ms delay required here as per DCS spec */ |
| msleep(120); |
| |
| ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_ENTER_SLEEP_MODE, NULL, 0); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "enter_sleep cmd failed ret = %d\n", ret); |
| } |
| |
| ret = visionox_rm69299_power_off(ctx); |
| |
| ctx->prepared = false; |
| return ret; |
| } |
| |
| static int visionox_rm69299_prepare(struct drm_panel *panel) |
| { |
| struct visionox_rm69299 *ctx = panel_to_ctx(panel); |
| int ret; |
| |
| if (ctx->prepared) |
| return 0; |
| |
| ret = visionox_rm69299_power_on(ctx); |
| if (ret < 0) |
| return ret; |
| |
| ctx->dsi->mode_flags |= MIPI_DSI_MODE_LPM; |
| |
| ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]) { 0xfe, 0x00 }, 2); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "cmd set tx 0 failed, ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]) { 0xc2, 0x08 }, 2); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "cmd set tx 1 failed, ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]) { 0x35, 0x00 }, 2); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "cmd set tx 2 failed, ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| ret = mipi_dsi_dcs_write_buffer(ctx->dsi, (u8[]) { 0x51, 0xff }, 2); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "cmd set tx 3 failed, ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_EXIT_SLEEP_MODE, NULL, 0); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "exit_sleep_mode cmd failed ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| /* Per DSI spec wait 120ms after sending exit sleep DCS command */ |
| msleep(120); |
| |
| ret = mipi_dsi_dcs_write(ctx->dsi, MIPI_DCS_SET_DISPLAY_ON, NULL, 0); |
| if (ret < 0) { |
| dev_err(ctx->panel.dev, "set_display_on cmd failed ret = %d\n", ret); |
| goto power_off; |
| } |
| |
| /* Per DSI spec wait 120ms after sending set_display_on DCS command */ |
| msleep(120); |
| |
| ctx->prepared = true; |
| |
| return 0; |
| |
| power_off: |
| return ret; |
| } |
| |
| static const struct drm_display_mode visionox_rm69299_1080x2248_60hz = { |
| .name = "1080x2248", |
| .clock = 158695, |
| .hdisplay = 1080, |
| .hsync_start = 1080 + 26, |
| .hsync_end = 1080 + 26 + 2, |
| .htotal = 1080 + 26 + 2 + 36, |
| .vdisplay = 2248, |
| .vsync_start = 2248 + 56, |
| .vsync_end = 2248 + 56 + 4, |
| .vtotal = 2248 + 56 + 4 + 4, |
| .flags = 0, |
| }; |
| |
| static int visionox_rm69299_get_modes(struct drm_panel *panel, |
| struct drm_connector *connector) |
| { |
| struct visionox_rm69299 *ctx = panel_to_ctx(panel); |
| struct drm_display_mode *mode; |
| |
| mode = drm_mode_create(connector->dev); |
| if (!mode) { |
| dev_err(ctx->panel.dev, "failed to create a new display mode\n"); |
| return 0; |
| } |
| |
| connector->display_info.width_mm = 74; |
| connector->display_info.height_mm = 131; |
| drm_mode_copy(mode, &visionox_rm69299_1080x2248_60hz); |
| mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; |
| drm_mode_probed_add(connector, mode); |
| |
| return 1; |
| } |
| |
| static const struct drm_panel_funcs visionox_rm69299_drm_funcs = { |
| .unprepare = visionox_rm69299_unprepare, |
| .prepare = visionox_rm69299_prepare, |
| .get_modes = visionox_rm69299_get_modes, |
| }; |
| |
| static int visionox_rm69299_probe(struct mipi_dsi_device *dsi) |
| { |
| struct device *dev = &dsi->dev; |
| struct visionox_rm69299 *ctx; |
| int ret; |
| |
| ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); |
| if (!ctx) |
| return -ENOMEM; |
| |
| mipi_dsi_set_drvdata(dsi, ctx); |
| |
| ctx->panel.dev = dev; |
| ctx->dsi = dsi; |
| |
| ctx->supplies[0].supply = "vdda"; |
| ctx->supplies[1].supply = "vdd3p3"; |
| |
| ret = devm_regulator_bulk_get(ctx->panel.dev, ARRAY_SIZE(ctx->supplies), |
| ctx->supplies); |
| if (ret < 0) |
| return ret; |
| |
| ctx->reset_gpio = devm_gpiod_get(ctx->panel.dev, |
| "reset", GPIOD_OUT_LOW); |
| if (IS_ERR(ctx->reset_gpio)) { |
| dev_err(dev, "cannot get reset gpio %ld\n", PTR_ERR(ctx->reset_gpio)); |
| return PTR_ERR(ctx->reset_gpio); |
| } |
| |
| drm_panel_init(&ctx->panel, dev, &visionox_rm69299_drm_funcs, |
| DRM_MODE_CONNECTOR_DSI); |
| ctx->panel.dev = dev; |
| ctx->panel.funcs = &visionox_rm69299_drm_funcs; |
| drm_panel_add(&ctx->panel); |
| |
| dsi->lanes = 4; |
| dsi->format = MIPI_DSI_FMT_RGB888; |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM | |
| MIPI_DSI_CLOCK_NON_CONTINUOUS; |
| ret = mipi_dsi_attach(dsi); |
| if (ret < 0) { |
| dev_err(dev, "dsi attach failed ret = %d\n", ret); |
| goto err_dsi_attach; |
| } |
| |
| ret = regulator_set_load(ctx->supplies[0].consumer, 32000); |
| if (ret) { |
| dev_err(dev, "regulator set load failed for vdda supply ret = %d\n", ret); |
| goto err_set_load; |
| } |
| |
| ret = regulator_set_load(ctx->supplies[1].consumer, 13200); |
| if (ret) { |
| dev_err(dev, "regulator set load failed for vdd3p3 supply ret = %d\n", ret); |
| goto err_set_load; |
| } |
| |
| return 0; |
| |
| err_set_load: |
| mipi_dsi_detach(dsi); |
| err_dsi_attach: |
| drm_panel_remove(&ctx->panel); |
| return ret; |
| } |
| |
| static int visionox_rm69299_remove(struct mipi_dsi_device *dsi) |
| { |
| struct visionox_rm69299 *ctx = mipi_dsi_get_drvdata(dsi); |
| |
| mipi_dsi_detach(ctx->dsi); |
| mipi_dsi_device_unregister(ctx->dsi); |
| |
| drm_panel_remove(&ctx->panel); |
| return 0; |
| } |
| |
| static const struct of_device_id visionox_rm69299_of_match[] = { |
| { .compatible = "visionox,rm69299-1080p-display", }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, visionox_rm69299_of_match); |
| |
| static struct mipi_dsi_driver visionox_rm69299_driver = { |
| .driver = { |
| .name = "panel-visionox-rm69299", |
| .of_match_table = visionox_rm69299_of_match, |
| }, |
| .probe = visionox_rm69299_probe, |
| .remove = visionox_rm69299_remove, |
| }; |
| module_mipi_dsi_driver(visionox_rm69299_driver); |
| |
| MODULE_DESCRIPTION("Visionox RM69299 DSI Panel Driver"); |
| MODULE_LICENSE("GPL v2"); |