blob: 2917fecf6c80d08b118cd0c1ec70da3e0483ecd1 [file] [log] [blame]
/*
* Copyright (C) 2017 Spreadtrum Communications Inc.
*
* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#define I2C_CTL 0x00
#define I2C_ADDR_CFG 0x04
#define I2C_COUNT 0x08
#define I2C_RX 0x0c
#define I2C_TX 0x10
#define I2C_STATUS 0x14
#define I2C_HSMODE_CFG 0x18
#define I2C_VERSION 0x1c
#define ADDR_DVD0 0x20
#define ADDR_DVD1 0x24
#define ADDR_STA0_DVD 0x28
#define ADDR_RST 0x2c
/* I2C_CTL */
#define STP_EN BIT(20)
#define FIFO_AF_LVL_MASK GENMASK(19, 16)
#define FIFO_AF_LVL 16
#define FIFO_AE_LVL_MASK GENMASK(15, 12)
#define FIFO_AE_LVL 12
#define I2C_DMA_EN BIT(11)
#define FULL_INTEN BIT(10)
#define EMPTY_INTEN BIT(9)
#define I2C_DVD_OPT BIT(8)
#define I2C_OUT_OPT BIT(7)
#define I2C_TRIM_OPT BIT(6)
#define I2C_HS_MODE BIT(4)
#define I2C_MODE BIT(3)
#define I2C_EN BIT(2)
#define I2C_INT_EN BIT(1)
#define I2C_START BIT(0)
/* I2C_STATUS */
#define SDA_IN BIT(21)
#define SCL_IN BIT(20)
#define FIFO_FULL BIT(4)
#define FIFO_EMPTY BIT(3)
#define I2C_INT BIT(2)
#define I2C_RX_ACK BIT(1)
#define I2C_BUSY BIT(0)
/* ADDR_RST */
#define I2C_RST BIT(0)
#define I2C_FIFO_DEEP 12
#define I2C_FIFO_FULL_THLD 15
#define I2C_FIFO_EMPTY_THLD 4
#define I2C_DATA_STEP 8
#define I2C_ADDR_DVD0_CALC(high, low) \
((((high) & GENMASK(15, 0)) << 16) | ((low) & GENMASK(15, 0)))
#define I2C_ADDR_DVD1_CALC(high, low) \
(((high) & GENMASK(31, 16)) | (((low) & GENMASK(31, 16)) >> 16))
/* timeout (ms) for pm runtime autosuspend */
#define SPRD_I2C_PM_TIMEOUT 1000
/* timeout (ms) for transfer message */
#define I2C_XFER_TIMEOUT 1000
/* SPRD i2c data structure */
struct sprd_i2c {
struct i2c_adapter adap;
struct device *dev;
void __iomem *base;
struct i2c_msg *msg;
struct clk *clk;
u32 src_clk;
u32 bus_freq;
struct completion complete;
u8 *buf;
u32 count;
int irq;
int err;
};
static void sprd_i2c_set_count(struct sprd_i2c *i2c_dev, u32 count)
{
writel(count, i2c_dev->base + I2C_COUNT);
}
static void sprd_i2c_send_stop(struct sprd_i2c *i2c_dev, int stop)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
if (stop)
writel(tmp & ~STP_EN, i2c_dev->base + I2C_CTL);
else
writel(tmp | STP_EN, i2c_dev->base + I2C_CTL);
}
static void sprd_i2c_clear_start(struct sprd_i2c *i2c_dev)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
writel(tmp & ~I2C_START, i2c_dev->base + I2C_CTL);
}
static void sprd_i2c_clear_ack(struct sprd_i2c *i2c_dev)
{
u32 tmp = readl(i2c_dev->base + I2C_STATUS);
writel(tmp & ~I2C_RX_ACK, i2c_dev->base + I2C_STATUS);
}
static void sprd_i2c_clear_irq(struct sprd_i2c *i2c_dev)
{
u32 tmp = readl(i2c_dev->base + I2C_STATUS);
writel(tmp & ~I2C_INT, i2c_dev->base + I2C_STATUS);
}
static void sprd_i2c_reset_fifo(struct sprd_i2c *i2c_dev)
{
writel(I2C_RST, i2c_dev->base + ADDR_RST);
}
static void sprd_i2c_set_devaddr(struct sprd_i2c *i2c_dev, struct i2c_msg *m)
{
writel(m->addr << 1, i2c_dev->base + I2C_ADDR_CFG);
}
static void sprd_i2c_write_bytes(struct sprd_i2c *i2c_dev, u8 *buf, u32 len)
{
u32 i;
for (i = 0; i < len; i++)
writeb(buf[i], i2c_dev->base + I2C_TX);
}
static void sprd_i2c_read_bytes(struct sprd_i2c *i2c_dev, u8 *buf, u32 len)
{
u32 i;
for (i = 0; i < len; i++)
buf[i] = readb(i2c_dev->base + I2C_RX);
}
static void sprd_i2c_set_full_thld(struct sprd_i2c *i2c_dev, u32 full_thld)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
tmp &= ~FIFO_AF_LVL_MASK;
tmp |= full_thld << FIFO_AF_LVL;
writel(tmp, i2c_dev->base + I2C_CTL);
};
static void sprd_i2c_set_empty_thld(struct sprd_i2c *i2c_dev, u32 empty_thld)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
tmp &= ~FIFO_AE_LVL_MASK;
tmp |= empty_thld << FIFO_AE_LVL;
writel(tmp, i2c_dev->base + I2C_CTL);
};
static void sprd_i2c_set_fifo_full_int(struct sprd_i2c *i2c_dev, int enable)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
if (enable)
tmp |= FULL_INTEN;
else
tmp &= ~FULL_INTEN;
writel(tmp, i2c_dev->base + I2C_CTL);
};
static void sprd_i2c_set_fifo_empty_int(struct sprd_i2c *i2c_dev, int enable)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
if (enable)
tmp |= EMPTY_INTEN;
else
tmp &= ~EMPTY_INTEN;
writel(tmp, i2c_dev->base + I2C_CTL);
};
static void sprd_i2c_opt_start(struct sprd_i2c *i2c_dev)
{
u32 tmp = readl(i2c_dev->base + I2C_CTL);
writel(tmp | I2C_START, i2c_dev->base + I2C_CTL);
}
static void sprd_i2c_opt_mode(struct sprd_i2c *i2c_dev, int rw)
{
u32 cmd = readl(i2c_dev->base + I2C_CTL) & ~I2C_MODE;
writel(cmd | rw << 3, i2c_dev->base + I2C_CTL);
}
static void sprd_i2c_data_transfer(struct sprd_i2c *i2c_dev)
{
u32 i2c_count = i2c_dev->count;
u32 need_tran = i2c_count <= I2C_FIFO_DEEP ? i2c_count : I2C_FIFO_DEEP;
struct i2c_msg *msg = i2c_dev->msg;
if (msg->flags & I2C_M_RD) {
sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, I2C_FIFO_FULL_THLD);
i2c_dev->count -= I2C_FIFO_FULL_THLD;
i2c_dev->buf += I2C_FIFO_FULL_THLD;
/*
* If the read data count is larger than rx fifo full threshold,
* we should enable the rx fifo full interrupt to read data
* again.
*/
if (i2c_dev->count >= I2C_FIFO_FULL_THLD)
sprd_i2c_set_fifo_full_int(i2c_dev, 1);
} else {
sprd_i2c_write_bytes(i2c_dev, i2c_dev->buf, need_tran);
i2c_dev->buf += need_tran;
i2c_dev->count -= need_tran;
/*
* If the write data count is arger than tx fifo depth which
* means we can not write all data in one time, then we should
* enable the tx fifo empty interrupt to write again.
*/
if (i2c_count > I2C_FIFO_DEEP)
sprd_i2c_set_fifo_empty_int(i2c_dev, 1);
}
}
static int sprd_i2c_handle_msg(struct i2c_adapter *i2c_adap,
struct i2c_msg *msg, bool is_last_msg)
{
struct sprd_i2c *i2c_dev = i2c_adap->algo_data;
unsigned long time_left;
i2c_dev->msg = msg;
i2c_dev->buf = msg->buf;
i2c_dev->count = msg->len;
reinit_completion(&i2c_dev->complete);
sprd_i2c_reset_fifo(i2c_dev);
sprd_i2c_set_devaddr(i2c_dev, msg);
sprd_i2c_set_count(i2c_dev, msg->len);
if (msg->flags & I2C_M_RD) {
sprd_i2c_opt_mode(i2c_dev, 1);
sprd_i2c_send_stop(i2c_dev, 1);
} else {
sprd_i2c_opt_mode(i2c_dev, 0);
sprd_i2c_send_stop(i2c_dev, !!is_last_msg);
}
/*
* We should enable rx fifo full interrupt to get data when receiving
* full data.
*/
if (msg->flags & I2C_M_RD)
sprd_i2c_set_fifo_full_int(i2c_dev, 1);
else
sprd_i2c_data_transfer(i2c_dev);
sprd_i2c_opt_start(i2c_dev);
time_left = wait_for_completion_timeout(&i2c_dev->complete,
msecs_to_jiffies(I2C_XFER_TIMEOUT));
if (!time_left)
return -ETIMEDOUT;
return i2c_dev->err;
}
static int sprd_i2c_master_xfer(struct i2c_adapter *i2c_adap,
struct i2c_msg *msgs, int num)
{
struct sprd_i2c *i2c_dev = i2c_adap->algo_data;
int im, ret;
ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0)
return ret;
for (im = 0; im < num - 1; im++) {
ret = sprd_i2c_handle_msg(i2c_adap, &msgs[im], 0);
if (ret)
goto err_msg;
}
ret = sprd_i2c_handle_msg(i2c_adap, &msgs[im++], 1);
err_msg:
pm_runtime_mark_last_busy(i2c_dev->dev);
pm_runtime_put_autosuspend(i2c_dev->dev);
return ret < 0 ? ret : im;
}
static u32 sprd_i2c_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
}
static const struct i2c_algorithm sprd_i2c_algo = {
.master_xfer = sprd_i2c_master_xfer,
.functionality = sprd_i2c_func,
};
static void sprd_i2c_set_clk(struct sprd_i2c *i2c_dev, u32 freq)
{
u32 apb_clk = i2c_dev->src_clk;
/*
* From I2C databook, the prescale calculation formula:
* prescale = freq_i2c / (4 * freq_scl) - 1;
*/
u32 i2c_dvd = apb_clk / (4 * freq) - 1;
/*
* From I2C databook, the high period of SCL clock is recommended as
* 40% (2/5), and the low period of SCL clock is recommended as 60%
* (3/5), then the formula should be:
* high = (prescale * 2 * 2) / 5
* low = (prescale * 2 * 3) / 5
*/
u32 high = ((i2c_dvd << 1) * 2) / 5;
u32 low = ((i2c_dvd << 1) * 3) / 5;
u32 div0 = I2C_ADDR_DVD0_CALC(high, low);
u32 div1 = I2C_ADDR_DVD1_CALC(high, low);
writel(div0, i2c_dev->base + ADDR_DVD0);
writel(div1, i2c_dev->base + ADDR_DVD1);
/* Start hold timing = hold time(us) * source clock */
if (freq == I2C_MAX_FAST_MODE_FREQ)
writel((6 * apb_clk) / 10000000, i2c_dev->base + ADDR_STA0_DVD);
else if (freq == I2C_MAX_STANDARD_MODE_FREQ)
writel((4 * apb_clk) / 1000000, i2c_dev->base + ADDR_STA0_DVD);
}
static void sprd_i2c_enable(struct sprd_i2c *i2c_dev)
{
u32 tmp = I2C_DVD_OPT;
writel(tmp, i2c_dev->base + I2C_CTL);
sprd_i2c_set_full_thld(i2c_dev, I2C_FIFO_FULL_THLD);
sprd_i2c_set_empty_thld(i2c_dev, I2C_FIFO_EMPTY_THLD);
sprd_i2c_set_clk(i2c_dev, i2c_dev->bus_freq);
sprd_i2c_reset_fifo(i2c_dev);
sprd_i2c_clear_irq(i2c_dev);
tmp = readl(i2c_dev->base + I2C_CTL);
writel(tmp | I2C_EN | I2C_INT_EN, i2c_dev->base + I2C_CTL);
}
static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
{
struct sprd_i2c *i2c_dev = dev_id;
struct i2c_msg *msg = i2c_dev->msg;
bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
u32 i2c_tran;
if (msg->flags & I2C_M_RD)
i2c_tran = i2c_dev->count >= I2C_FIFO_FULL_THLD;
else
i2c_tran = i2c_dev->count;
/*
* If we got one ACK from slave when writing data, and we did not
* finish this transmission (i2c_tran is not zero), then we should
* continue to write data.
*
* For reading data, ack is always true, if i2c_tran is not 0 which
* means we still need to contine to read data from slave.
*/
if (i2c_tran && ack) {
sprd_i2c_data_transfer(i2c_dev);
return IRQ_HANDLED;
}
i2c_dev->err = 0;
/*
* If we did not get one ACK from slave when writing data, we should
* return -EIO to notify users.
*/
if (!ack)
i2c_dev->err = -EIO;
else if (msg->flags & I2C_M_RD && i2c_dev->count)
sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, i2c_dev->count);
/* Transmission is done and clear ack and start operation */
sprd_i2c_clear_ack(i2c_dev);
sprd_i2c_clear_start(i2c_dev);
complete(&i2c_dev->complete);
return IRQ_HANDLED;
}
static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
{
struct sprd_i2c *i2c_dev = dev_id;
struct i2c_msg *msg = i2c_dev->msg;
bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
u32 i2c_tran;
if (msg->flags & I2C_M_RD)
i2c_tran = i2c_dev->count >= I2C_FIFO_FULL_THLD;
else
i2c_tran = i2c_dev->count;
/*
* If we did not get one ACK from slave when writing data, then we
* should finish this transmission since we got some errors.
*
* When writing data, if i2c_tran == 0 which means we have writen
* done all data, then we can finish this transmission.
*
* When reading data, if conut < rx fifo full threshold, which
* means we can read all data in one time, then we can finish this
* transmission too.
*/
if (!i2c_tran || !ack) {
sprd_i2c_clear_start(i2c_dev);
sprd_i2c_clear_irq(i2c_dev);
}
sprd_i2c_set_fifo_empty_int(i2c_dev, 0);
sprd_i2c_set_fifo_full_int(i2c_dev, 0);
return IRQ_WAKE_THREAD;
}
static int sprd_i2c_clk_init(struct sprd_i2c *i2c_dev)
{
struct clk *clk_i2c, *clk_parent;
clk_i2c = devm_clk_get(i2c_dev->dev, "i2c");
if (IS_ERR(clk_i2c)) {
dev_warn(i2c_dev->dev, "i2c%d can't get the i2c clock\n",
i2c_dev->adap.nr);
clk_i2c = NULL;
}
clk_parent = devm_clk_get(i2c_dev->dev, "source");
if (IS_ERR(clk_parent)) {
dev_warn(i2c_dev->dev, "i2c%d can't get the source clock\n",
i2c_dev->adap.nr);
clk_parent = NULL;
}
if (clk_set_parent(clk_i2c, clk_parent))
i2c_dev->src_clk = clk_get_rate(clk_i2c);
else
i2c_dev->src_clk = 26000000;
dev_dbg(i2c_dev->dev, "i2c%d set source clock is %d\n",
i2c_dev->adap.nr, i2c_dev->src_clk);
i2c_dev->clk = devm_clk_get(i2c_dev->dev, "enable");
if (IS_ERR(i2c_dev->clk)) {
dev_err(i2c_dev->dev, "i2c%d can't get the enable clock\n",
i2c_dev->adap.nr);
return PTR_ERR(i2c_dev->clk);
}
return 0;
}
static int sprd_i2c_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct sprd_i2c *i2c_dev;
u32 prop;
int ret;
pdev->id = of_alias_get_id(dev->of_node, "i2c");
i2c_dev = devm_kzalloc(dev, sizeof(struct sprd_i2c), GFP_KERNEL);
if (!i2c_dev)
return -ENOMEM;
i2c_dev->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(i2c_dev->base))
return PTR_ERR(i2c_dev->base);
i2c_dev->irq = platform_get_irq(pdev, 0);
if (i2c_dev->irq < 0)
return i2c_dev->irq;
i2c_set_adapdata(&i2c_dev->adap, i2c_dev);
init_completion(&i2c_dev->complete);
snprintf(i2c_dev->adap.name, sizeof(i2c_dev->adap.name),
"%s", "sprd-i2c");
i2c_dev->bus_freq = I2C_MAX_STANDARD_MODE_FREQ;
i2c_dev->adap.owner = THIS_MODULE;
i2c_dev->dev = dev;
i2c_dev->adap.retries = 3;
i2c_dev->adap.algo = &sprd_i2c_algo;
i2c_dev->adap.algo_data = i2c_dev;
i2c_dev->adap.dev.parent = dev;
i2c_dev->adap.nr = pdev->id;
i2c_dev->adap.dev.of_node = dev->of_node;
if (!of_property_read_u32(dev->of_node, "clock-frequency", &prop))
i2c_dev->bus_freq = prop;
/* We only support 100k and 400k now, otherwise will return error. */
if (i2c_dev->bus_freq != I2C_MAX_STANDARD_MODE_FREQ &&
i2c_dev->bus_freq != I2C_MAX_FAST_MODE_FREQ)
return -EINVAL;
ret = sprd_i2c_clk_init(i2c_dev);
if (ret)
return ret;
platform_set_drvdata(pdev, i2c_dev);
ret = clk_prepare_enable(i2c_dev->clk);
if (ret)
return ret;
sprd_i2c_enable(i2c_dev);
pm_runtime_set_autosuspend_delay(i2c_dev->dev, SPRD_I2C_PM_TIMEOUT);
pm_runtime_use_autosuspend(i2c_dev->dev);
pm_runtime_set_active(i2c_dev->dev);
pm_runtime_enable(i2c_dev->dev);
ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0)
goto err_rpm_put;
ret = devm_request_threaded_irq(dev, i2c_dev->irq,
sprd_i2c_isr, sprd_i2c_isr_thread,
IRQF_NO_SUSPEND | IRQF_ONESHOT,
pdev->name, i2c_dev);
if (ret) {
dev_err(&pdev->dev, "failed to request irq %d\n", i2c_dev->irq);
goto err_rpm_put;
}
ret = i2c_add_numbered_adapter(&i2c_dev->adap);
if (ret) {
dev_err(&pdev->dev, "add adapter failed\n");
goto err_rpm_put;
}
pm_runtime_mark_last_busy(i2c_dev->dev);
pm_runtime_put_autosuspend(i2c_dev->dev);
return 0;
err_rpm_put:
pm_runtime_put_noidle(i2c_dev->dev);
pm_runtime_disable(i2c_dev->dev);
clk_disable_unprepare(i2c_dev->clk);
return ret;
}
static int sprd_i2c_remove(struct platform_device *pdev)
{
struct sprd_i2c *i2c_dev = platform_get_drvdata(pdev);
int ret;
ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0)
return ret;
i2c_del_adapter(&i2c_dev->adap);
clk_disable_unprepare(i2c_dev->clk);
pm_runtime_put_noidle(i2c_dev->dev);
pm_runtime_disable(i2c_dev->dev);
return 0;
}
static int __maybe_unused sprd_i2c_suspend_noirq(struct device *dev)
{
struct sprd_i2c *i2c_dev = dev_get_drvdata(dev);
i2c_mark_adapter_suspended(&i2c_dev->adap);
return pm_runtime_force_suspend(dev);
}
static int __maybe_unused sprd_i2c_resume_noirq(struct device *dev)
{
struct sprd_i2c *i2c_dev = dev_get_drvdata(dev);
i2c_mark_adapter_resumed(&i2c_dev->adap);
return pm_runtime_force_resume(dev);
}
static int __maybe_unused sprd_i2c_runtime_suspend(struct device *dev)
{
struct sprd_i2c *i2c_dev = dev_get_drvdata(dev);
clk_disable_unprepare(i2c_dev->clk);
return 0;
}
static int __maybe_unused sprd_i2c_runtime_resume(struct device *dev)
{
struct sprd_i2c *i2c_dev = dev_get_drvdata(dev);
int ret;
ret = clk_prepare_enable(i2c_dev->clk);
if (ret)
return ret;
sprd_i2c_enable(i2c_dev);
return 0;
}
static const struct dev_pm_ops sprd_i2c_pm_ops = {
SET_RUNTIME_PM_OPS(sprd_i2c_runtime_suspend,
sprd_i2c_runtime_resume, NULL)
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(sprd_i2c_suspend_noirq,
sprd_i2c_resume_noirq)
};
static const struct of_device_id sprd_i2c_of_match[] = {
{ .compatible = "sprd,sc9860-i2c", },
{},
};
static struct platform_driver sprd_i2c_driver = {
.probe = sprd_i2c_probe,
.remove = sprd_i2c_remove,
.driver = {
.name = "sprd-i2c",
.of_match_table = sprd_i2c_of_match,
.pm = &sprd_i2c_pm_ops,
},
};
module_platform_driver(sprd_i2c_driver);
MODULE_DESCRIPTION("Spreadtrum I2C master controller driver");
MODULE_LICENSE("GPL v2");