blob: 3f13a960f34efd4b22769a0d9e29b5da76f5453c [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* dts file for Hisilicon HiKey960 Development Board
*
* Copyright (C) 2016, HiSilicon Ltd.
*
*/
/dts-v1/;
#include "hi3660.dtsi"
#include "hikey960-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/usb/pd.h>
/ {
model = "HiKey960";
compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660";
aliases {
mshc1 = &dwmmc1;
mshc2 = &dwmmc2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
serial6 = &uart6;
};
chosen {
stdout-path = "serial6:115200n8";
};
memory@0 {
device_type = "memory";
/* rewrite this at bootloader */
reg = <0x0 0x0 0x0 0x0>;
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
ramoops@32000000 {
compatible = "ramoops";
reg = <0x0 0x32000000 0x0 0x00100000>;
record-size = <0x00020000>;
console-size = <0x00020000>;
ftrace-size = <0x00020000>;
};
};
reboot-mode-syscon@32100000 {
compatible = "syscon", "simple-mfd";
reg = <0x0 0x32100000 0x0 0x00001000>;
reboot-mode {
compatible = "syscon-reboot-mode";
offset = <0x0>;
mode-normal = <0x77665501>;
mode-bootloader = <0x77665500>;
mode-recovery = <0x77665502>;
};
};
keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pwr_key_pmx_func &pwr_key_cfg_func>;
key-power {
wakeup-source;
gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <KEY_POWER>;
};
};
leds {
compatible = "gpio-leds";
led-user-1 {
label = "green:user1";
/* gpio_150_user_led1 */
gpios = <&gpio18 6 0>;
linux,default-trigger = "heartbeat";
};
led-user-2 {
label = "green:user2";
/* gpio_151_user_led2 */
gpios = <&gpio18 7 0>;
linux,default-trigger = "none";
};
led-user-3 {
label = "green:user3";
/* gpio_189_user_led3 */
gpios = <&gpio23 5 0>;
linux,default-trigger = "mmc0";
};
led-user-4 {
label = "green:user4";
/* gpio_190_user_led4 */
gpios = <&gpio23 6 0>;
panic-indicator;
linux,default-trigger = "none";
};
led-wlan {
label = "yellow:wlan";
/* gpio_205_wifi_active */
gpios = <&gpio25 5 0>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
led-bt {
label = "blue:bt";
gpios = <&gpio25 7 0>;
/* gpio_207_user_led1 */
linux,default-trigger = "hci0-power";
default-state = "off";
};
};
pmic: pmic@fff34000 {
compatible = "hisilicon,hi6421v530-pmic";
reg = <0x0 0xfff34000 0x0 0x1000>;
interrupt-controller;
#interrupt-cells = <2>;
regulators {
ldo3: LDO3 { /* HDMI */
regulator-name = "VOUT3_1V85";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2200000>;
regulator-enable-ramp-delay = <120>;
};
ldo9: LDO9 { /* SDCARD I/O */
regulator-name = "VOUT9_1V8_2V95";
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3300000>;
regulator-enable-ramp-delay = <240>;
};
ldo11: LDO11 { /* Low Speed Connector */
regulator-name = "VOUT11_1V8_2V95";
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3300000>;
regulator-enable-ramp-delay = <240>;
};
ldo15: LDO15 { /* UFS VCC */
regulator-name = "VOUT15_3V0";
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
regulator-always-on;
regulator-enable-ramp-delay = <120>;
};
ldo16: LDO16 { /* SD VDD */
regulator-name = "VOUT16_2V95";
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3000000>;
regulator-enable-ramp-delay = <360>;
};
};
};
wlan_en: wlan-en-1-8v {
compatible = "regulator-fixed";
regulator-name = "wlan-en-regulator";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
/* GPIO_051_WIFI_EN */
gpio = <&gpio6 3 0>;
/* WLAN card specific delay */
startup-delay-us = <70000>;
enable-active-high;
};
firmware {
optee {
compatible = "linaro,optee-tz";
method = "smc";
};
};
};
/*
* Legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* "" = no idea, schematic doesn't say, could be
* unrouted (not connected to any external pin)
* LSEC = Low Speed External Connector
* HSEC = High Speed External Connector
*
* Line names are taken from "HiKey 960 Board ver A" schematics
* from Huawei. The 40 pin low speed expansion connector is named
* J2002 63453-140LF.
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART3. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
&gpio0 {
/* GPIO_000-GPIO_007 */
gpio-line-names =
"",
"TP901", /* TEST_MODE connected to TP901 */
"[PMU0_SSI]",
"[PMU1_SSI]",
"[PMU2_SSI]",
"[PMU0_CLKOUT]",
"[JTAG_TCK]",
"[JTAG_TMS]";
};
&gpio1 {
/* GPIO_008-GPIO_015 */
gpio-line-names =
"[JTAG_TRST_N]",
"[JTAG_TDI]",
"[JTAG_TDO]",
"NC", "NC",
"[I2C3_SCL]",
"[I2C3_SDA]",
"NC";
};
&gpio2 {
/* GPIO_016-GPIO_023 */
gpio-line-names =
"NC", "NC", "NC",
"GPIO-J", /* LSEC pin 32: GPIO_019 */
"GPIO_020_HDMI_SEL",
"GPIO-L", /* LSEC pin 34: GPIO_021 */
"GPIO_022_UFSBUCK_INT_N",
"GPIO-G"; /* LSEC pin 29: LCD_TE0 */
};
&gpio3 {
/* GPIO_024-GPIO_031 */
/* The rail from pin BK36 is named LCD_TE0, we assume to be muxed as GPIO for GPIO-G */
gpio-line-names =
"[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
"[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
"NC",
"[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
"[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
"[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
"[I2C3_SDA]", /* HSEC pin 38: ISP_SDA1 */
"NC";
};
&gpio4 {
/* GPIO_032-GPIO_039 */
gpio-line-names =
"NC", "NC",
"PWR_BTN_N", /* LSEC pin 4: GPIO_034_PWRON_DET */
"GPIO_035_PMU2_EN",
"GPIO_036_USB_HUB_RESET",
"NC", "NC", "NC";
};
&gpio5 {
/* GPIO_040-GPIO_047 */
gpio-line-names =
"GPIO-H", /* LSEC pin 30: GPIO_040_LCD_RST_N */
"GPIO_041_HDMI_PD",
"TP904", /* Test point */
"TP905", /* Test point */
"NC", "NC",
"GPIO_046_HUB_VDD33_EN",
"GPIO_047_PMU1_EN";
};
&gpio6 {
/* GPIO_048-GPIO_055 */
gpio-line-names =
"NC", "NC", "NC",
"GPIO_051_WIFI_EN",
"GPIO-I", /* LSEC pin 31: GPIO_052_CAM0_RST_N */
/*
* These two pins should be used for SD(IO) data according to the
* 96boards specification but seems to be repurposed for a IRDA UART.
* They are however named according to the spec.
*/
"[SD_DAT1]", /* HSEC pin 3: UART0_IRDA_RXD */
"[SD_DAT2]", /* HSEC pin 5: UART0_IRDA_TXD */
"[UART1_RXD]"; /* LSEC pin 13: DEBUG_UART6_RXD */
};
&gpio7 {
/* GPIO_056-GPIO_063 */
gpio-line-names =
"[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
"[UART0_CTS]", /* LSEC pin 3: UART3_CTS_N */
"[UART0_RTS]", /* LSEC pin 9: UART3_RTS_N */
"[UART0_RXD]", /* LSEC pin 7: UART3_RXD */
"[UART0_TXD]", /* LSEC pin 5: UART3_TXD */
"[SOC_BT_UART4_CTS_N]",
"[SOC_BT_UART4_RTS_N]",
"[SOC_BT_UART4_RXD]";
};
&gpio8 {
/* GPIO_064-GPIO_071 */
gpio-line-names =
"[SOC_BT_UART4_TXD]",
"NC",
"[PMU_HKADC_SSI]",
"NC",
"GPIO_068_SEL",
"NC", "NC", "NC";
};
&gpio9 {
/* GPIO_072-GPIO_079 */
gpio-line-names =
"NC", "NC", "NC",
"GPIO-K", /* LSEC pin 33: GPIO_075_CAM1_RST_N */
"NC", "NC", "NC", "NC";
};
&gpio10 {
/* GPIO_080-GPIO_087 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio11 {
/* GPIO_088-GPIO_095 */
gpio-line-names =
"NC",
"[PCIE_PERST_N]",
"NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio12 {
/* GPIO_096-GPIO_103 */
gpio-line-names = "NC", "NC", "NC", "", "", "", "", "NC";
};
&gpio13 {
/* GPIO_104-GPIO_111 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio14 {
/* GPIO_112-GPIO_119 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio15 {
/* GPIO_120-GPIO_127 */
gpio-line-names =
"NC", "NC", "NC", "NC", "NC", "NC",
"GPIO_126_BT_EN",
"TP902"; /* GPIO_127_JTAG_SEL0 */
};
&gpio16 {
/* GPIO_128-GPIO_135 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio17 {
/* GPIO_136-GPIO_143 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio18 {
/* GPIO_144-GPIO_151 */
gpio-line-names =
"[UFS_REF_CLK]",
"[UFS_RST_N]",
"[SPI1_SCLK]", /* HSEC pin 9: GPIO_146_SPI3_CLK */
"[SPI1_DIN]", /* HSEC pin 11: GPIO_147_SPI3_DI */
"[SPI1_DOUT]", /* HSEC pin 1: GPIO_148_SPI3_DO */
"[SPI1_CS]", /* HSEC pin 7: GPIO_149_SPI3_CS0_N */
"GPIO_150_USER_LED1",
"GPIO_151_USER_LED2";
};
&gpio19 {
/* GPIO_152-GPIO_159 */
gpio-line-names = "NC", "NC", "NC", "NC", "", "", "", "";
};
&gpio20 {
/* GPIO_160-GPIO_167 */
gpio-line-names =
"[SD_CLK]",
"[SD_CMD]",
"[SD_DATA0]",
"[SD_DATA1]",
"[SD_DATA2]",
"[SD_DATA3]",
"", "";
};
&gpio21 {
/* GPIO_168-GPIO_175 */
gpio-line-names =
"[WL_SDIO_CLK]",
"[WL_SDIO_CMD]",
"[WL_SDIO_DATA0]",
"[WL_SDIO_DATA1]",
"[WL_SDIO_DATA2]",
"[WL_SDIO_DATA3]",
"", "";
};
&gpio22 {
/* GPIO_176-GPIO_183 */
gpio-line-names =
"[GPIO_176_PMU_PWR_HOLD]",
"NA",
"[SYSCLK_EN]",
"GPIO_179_WL_WAKEUP_AP",
"GPIO_180_HDMI_INT",
"NA",
"GPIO-F", /* LSEC pin 28: LCD_BL_PWM */
"[I2C0_SCL]"; /* LSEC pin 15 */
};
&gpio23 {
/* GPIO_184-GPIO_191 */
gpio-line-names =
"[I2C0_SDA]", /* LSEC pin 17 */
"[I2C1_SCL]", /* Actual SoC I2C1 */
"[I2C1_SDA]", /* Actual SoC I2C1 */
"[I2C1_SCL]", /* LSEC pin 19: I2C7_SCL */
"[I2C1_SDA]", /* LSEC pin 21: I2C7_SDA */
"GPIO_189_USER_LED3",
"GPIO_190_USER_LED4",
"";
};
&gpio24 {
/* GPIO_192-GPIO_199 */
gpio-line-names =
"[PCM_DI]", /* LSEC pin 22: GPIO_192_I2S0_DI */
"[PCM_DO]", /* LSEC pin 20: GPIO_193_I2S0_DO */
"[PCM_CLK]", /* LSEC pin 18: GPIO_194_I2S0_XCLK */
"[PCM_FS]", /* LSEC pin 16: GPIO_195_I2S0_XFS */
"[GPIO_196_I2S2_DI]",
"[GPIO_197_I2S2_DO]",
"[GPIO_198_I2S2_XCLK]",
"[GPIO_199_I2S2_XFS]";
};
&gpio25 {
/* GPIO_200-GPIO_207 */
gpio-line-names =
"NC",
"NC",
"GPIO_202_VBUS_TYPEC",
"GPIO_203_SD_DET",
"GPIO_204_PMU12_IRQ_N",
"GPIO_205_WIFI_ACTIVE",
"GPIO_206_USBSW_SEL",
"GPIO_207_BT_ACTIVE";
};
&gpio26 {
/* GPIO_208-GPIO_215 */
gpio-line-names =
"GPIO-A", /* LSEC pin 23: GPIO_208 */
"GPIO-B", /* LSEC pin 24: GPIO_209 */
"GPIO-C", /* LSEC pin 25: GPIO_210 */
"GPIO-D", /* LSEC pin 26: GPIO_211 */
"GPIO-E", /* LSEC pin 27: GPIO_212 */
"[PCIE_CLKREQ_N]",
"[PCIE_WAKE_N]",
"[SPI0_CLK]"; /* LSEC pin 8: SPI2_CLK */
};
&gpio27 {
/* GPIO_216-GPIO_223 */
gpio-line-names =
"[SPI0_DIN]", /* LSEC pin 10: SPI2_DI */
"[SPI0_DOUT]", /* LSEC pin 14: SPI2_DO */
"[SPI0_CS]", /* LSEC pin 12: SPI2_CS0_N */
"GPIO_219_CC_INT",
"NC",
"NC",
"[PMU_INT]",
"";
};
&gpio28 {
/* GPIO_224-GPIO_231 */
gpio-line-names =
"", "", "", "", "", "", "", "";
};
&i2c0 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
&i2c1 {
status = "okay";
rt1711h: rt1711h@4e {
compatible = "richtek,rt1711h";
reg = <0x4e>;
status = "okay";
interrupt-parent = <&gpio27>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&usb_cfg_func>;
usb_con: connector {
compatible = "usb-c-connector";
label = "USB-C";
data-role = "dual";
power-role = "dual";
try-power-role = "sink";
source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
PDO_VAR(5000, 5000, 1000)>;
op-sink-microwatt = <10000000>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
usb_con_ss: endpoint {
remote-endpoint = <&dwc3_ss>;
};
};
};
};
port {
#address-cells = <1>;
#size-cells = <0>;
rt1711h_ep: endpoint@0 {
reg = <0>;
remote-endpoint = <&dwc3_role_switch>;
};
};
};
adv7533: adv7533@39 {
status = "okay";
compatible = "adi,adv7533";
reg = <0x39>;
adi,dsi-lanes = <4>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
};
port@1 {
reg = <1>;
};
};
};
};
&i2c7 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
&uart3 {
/* On Low speed expansion */
label = "LS-UART0";
status = "okay";
};
&uart4 {
status = "okay";
bluetooth {
compatible = "ti,wl1837-st";
enable-gpios = <&gpio15 6 GPIO_ACTIVE_HIGH>;
max-speed = <3000000>;
};
};
&uart6 {
/* On Low speed expansion */
label = "LS-UART1";
status = "okay";
};
&spi2 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
&spi3 {
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
&dwmmc1 {
bus-width = <0x4>;
cap-sd-highspeed;
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
sd-uhs-sdr104;
disable-wp;
cd-gpios = <&gpio25 3 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sd_pmx_func
&sd_clk_cfg_func
&sd_cfg_func>;
vmmc-supply = <&ldo16>;
vqmmc-supply = <&ldo9>;
status = "okay";
};
&dwmmc2 { /* WIFI */
bus-width = <0x4>;
non-removable;
broken-cd;
cap-power-off-card;
pinctrl-names = "default";
pinctrl-0 = <&sdio_pmx_func
&sdio_clk_cfg_func
&sdio_cfg_func>;
/* WL_EN */
vmmc-supply = <&wlan_en>;
status = "okay";
wlcore: wlcore@2 {
compatible = "ti,wl1837";
reg = <2>; /* sdio func num */
/* WL_IRQ, GPIO_179_WL_WAKEUP_AP */
interrupt-parent = <&gpio22>;
interrupts = <3 IRQ_TYPE_EDGE_RISING>;
};
};
&dwc3 { /* USB */
dr_mode = "otg";
maximum-speed = "super-speed";
phy_type = "utmi";
snps,dis-del-phy-power-chg-quirk;
snps,lfps_filter_quirk;
snps,dis_u2_susphy_quirk;
snps,dis_u3_susphy_quirk;
snps,tx_de_emphasis_quirk;
snps,tx_de_emphasis = <1>;
snps,dis_enblslpm_quirk;
snps,gctl-reset-quirk;
usb-role-switch;
role-switch-default-mode = "host";
port {
#address-cells = <1>;
#size-cells = <0>;
dwc3_role_switch: endpoint@0 {
reg = <0>;
remote-endpoint = <&rt1711h_ep>;
};
dwc3_ss: endpoint@1 {
reg = <1>;
remote-endpoint = <&usb_con_ss>;
};
};
};