| /* |
| * Blackfin On-Chip MAC Driver |
| * |
| * Copyright 2004-2007 Analog Devices Inc. |
| * |
| * Enter bugs at http://blackfin.uclinux.org/ |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #include <linux/init.h> |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/sched.h> |
| #include <linux/slab.h> |
| #include <linux/delay.h> |
| #include <linux/timer.h> |
| #include <linux/errno.h> |
| #include <linux/irq.h> |
| #include <linux/io.h> |
| #include <linux/ioport.h> |
| #include <linux/crc32.h> |
| #include <linux/device.h> |
| #include <linux/spinlock.h> |
| #include <linux/mii.h> |
| #include <linux/phy.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/ethtool.h> |
| #include <linux/skbuff.h> |
| #include <linux/platform_device.h> |
| |
| #include <asm/dma.h> |
| #include <linux/dma-mapping.h> |
| |
| #include <asm/blackfin.h> |
| #include <asm/cacheflush.h> |
| #include <asm/portmux.h> |
| |
| #include "bfin_mac.h" |
| |
| #define DRV_NAME "bfin_mac" |
| #define DRV_VERSION "1.1" |
| #define DRV_AUTHOR "Bryan Wu, Luke Yang" |
| #define DRV_DESC "Blackfin on-chip Ethernet MAC driver" |
| |
| MODULE_AUTHOR(DRV_AUTHOR); |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION(DRV_DESC); |
| MODULE_ALIAS("platform:bfin_mac"); |
| |
| #if defined(CONFIG_BFIN_MAC_USE_L1) |
| # define bfin_mac_alloc(dma_handle, size) l1_data_sram_zalloc(size) |
| # define bfin_mac_free(dma_handle, ptr) l1_data_sram_free(ptr) |
| #else |
| # define bfin_mac_alloc(dma_handle, size) \ |
| dma_alloc_coherent(NULL, size, dma_handle, GFP_KERNEL) |
| # define bfin_mac_free(dma_handle, ptr) \ |
| dma_free_coherent(NULL, sizeof(*ptr), ptr, dma_handle) |
| #endif |
| |
| #define PKT_BUF_SZ 1580 |
| |
| #define MAX_TIMEOUT_CNT 500 |
| |
| /* pointers to maintain transmit list */ |
| static struct net_dma_desc_tx *tx_list_head; |
| static struct net_dma_desc_tx *tx_list_tail; |
| static struct net_dma_desc_rx *rx_list_head; |
| static struct net_dma_desc_rx *rx_list_tail; |
| static struct net_dma_desc_rx *current_rx_ptr; |
| static struct net_dma_desc_tx *current_tx_ptr; |
| static struct net_dma_desc_tx *tx_desc; |
| static struct net_dma_desc_rx *rx_desc; |
| |
| #if defined(CONFIG_BFIN_MAC_RMII) |
| static u16 pin_req[] = P_RMII0; |
| #else |
| static u16 pin_req[] = P_MII0; |
| #endif |
| |
| static void bfin_mac_disable(void); |
| static void bfin_mac_enable(void); |
| |
| static void desc_list_free(void) |
| { |
| struct net_dma_desc_rx *r; |
| struct net_dma_desc_tx *t; |
| int i; |
| #if !defined(CONFIG_BFIN_MAC_USE_L1) |
| dma_addr_t dma_handle = 0; |
| #endif |
| |
| if (tx_desc) { |
| t = tx_list_head; |
| for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) { |
| if (t) { |
| if (t->skb) { |
| dev_kfree_skb(t->skb); |
| t->skb = NULL; |
| } |
| t = t->next; |
| } |
| } |
| bfin_mac_free(dma_handle, tx_desc); |
| } |
| |
| if (rx_desc) { |
| r = rx_list_head; |
| for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) { |
| if (r) { |
| if (r->skb) { |
| dev_kfree_skb(r->skb); |
| r->skb = NULL; |
| } |
| r = r->next; |
| } |
| } |
| bfin_mac_free(dma_handle, rx_desc); |
| } |
| } |
| |
| static int desc_list_init(void) |
| { |
| int i; |
| struct sk_buff *new_skb; |
| #if !defined(CONFIG_BFIN_MAC_USE_L1) |
| /* |
| * This dma_handle is useless in Blackfin dma_alloc_coherent(). |
| * The real dma handler is the return value of dma_alloc_coherent(). |
| */ |
| dma_addr_t dma_handle; |
| #endif |
| |
| tx_desc = bfin_mac_alloc(&dma_handle, |
| sizeof(struct net_dma_desc_tx) * |
| CONFIG_BFIN_TX_DESC_NUM); |
| if (tx_desc == NULL) |
| goto init_error; |
| |
| rx_desc = bfin_mac_alloc(&dma_handle, |
| sizeof(struct net_dma_desc_rx) * |
| CONFIG_BFIN_RX_DESC_NUM); |
| if (rx_desc == NULL) |
| goto init_error; |
| |
| /* init tx_list */ |
| tx_list_head = tx_list_tail = tx_desc; |
| |
| for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) { |
| struct net_dma_desc_tx *t = tx_desc + i; |
| struct dma_descriptor *a = &(t->desc_a); |
| struct dma_descriptor *b = &(t->desc_b); |
| |
| /* |
| * disable DMA |
| * read from memory WNR = 0 |
| * wordsize is 32 bits |
| * 6 half words is desc size |
| * large desc flow |
| */ |
| a->config = WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE; |
| a->start_addr = (unsigned long)t->packet; |
| a->x_count = 0; |
| a->next_dma_desc = b; |
| |
| /* |
| * enabled DMA |
| * write to memory WNR = 1 |
| * wordsize is 32 bits |
| * disable interrupt |
| * 6 half words is desc size |
| * large desc flow |
| */ |
| b->config = DMAEN | WNR | WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE; |
| b->start_addr = (unsigned long)(&(t->status)); |
| b->x_count = 0; |
| |
| t->skb = NULL; |
| tx_list_tail->desc_b.next_dma_desc = a; |
| tx_list_tail->next = t; |
| tx_list_tail = t; |
| } |
| tx_list_tail->next = tx_list_head; /* tx_list is a circle */ |
| tx_list_tail->desc_b.next_dma_desc = &(tx_list_head->desc_a); |
| current_tx_ptr = tx_list_head; |
| |
| /* init rx_list */ |
| rx_list_head = rx_list_tail = rx_desc; |
| |
| for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) { |
| struct net_dma_desc_rx *r = rx_desc + i; |
| struct dma_descriptor *a = &(r->desc_a); |
| struct dma_descriptor *b = &(r->desc_b); |
| |
| /* allocate a new skb for next time receive */ |
| new_skb = dev_alloc_skb(PKT_BUF_SZ + NET_IP_ALIGN); |
| if (!new_skb) { |
| printk(KERN_NOTICE DRV_NAME |
| ": init: low on mem - packet dropped\n"); |
| goto init_error; |
| } |
| skb_reserve(new_skb, NET_IP_ALIGN); |
| r->skb = new_skb; |
| |
| /* |
| * enabled DMA |
| * write to memory WNR = 1 |
| * wordsize is 32 bits |
| * disable interrupt |
| * 6 half words is desc size |
| * large desc flow |
| */ |
| a->config = DMAEN | WNR | WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE; |
| /* since RXDWA is enabled */ |
| a->start_addr = (unsigned long)new_skb->data - 2; |
| a->x_count = 0; |
| a->next_dma_desc = b; |
| |
| /* |
| * enabled DMA |
| * write to memory WNR = 1 |
| * wordsize is 32 bits |
| * enable interrupt |
| * 6 half words is desc size |
| * large desc flow |
| */ |
| b->config = DMAEN | WNR | WDSIZE_32 | DI_EN | |
| NDSIZE_6 | DMAFLOW_LARGE; |
| b->start_addr = (unsigned long)(&(r->status)); |
| b->x_count = 0; |
| |
| rx_list_tail->desc_b.next_dma_desc = a; |
| rx_list_tail->next = r; |
| rx_list_tail = r; |
| } |
| rx_list_tail->next = rx_list_head; /* rx_list is a circle */ |
| rx_list_tail->desc_b.next_dma_desc = &(rx_list_head->desc_a); |
| current_rx_ptr = rx_list_head; |
| |
| return 0; |
| |
| init_error: |
| desc_list_free(); |
| printk(KERN_ERR DRV_NAME ": kmalloc failed\n"); |
| return -ENOMEM; |
| } |
| |
| |
| /*---PHY CONTROL AND CONFIGURATION-----------------------------------------*/ |
| |
| /* |
| * MII operations |
| */ |
| /* Wait until the previous MDC/MDIO transaction has completed */ |
| static void bfin_mdio_poll(void) |
| { |
| int timeout_cnt = MAX_TIMEOUT_CNT; |
| |
| /* poll the STABUSY bit */ |
| while ((bfin_read_EMAC_STAADD()) & STABUSY) { |
| udelay(1); |
| if (timeout_cnt-- < 0) { |
| printk(KERN_ERR DRV_NAME |
| ": wait MDC/MDIO transaction to complete timeout\n"); |
| break; |
| } |
| } |
| } |
| |
| /* Read an off-chip register in a PHY through the MDC/MDIO port */ |
| static int bfin_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum) |
| { |
| bfin_mdio_poll(); |
| |
| /* read mode */ |
| bfin_write_EMAC_STAADD(SET_PHYAD((u16) phy_addr) | |
| SET_REGAD((u16) regnum) | |
| STABUSY); |
| |
| bfin_mdio_poll(); |
| |
| return (int) bfin_read_EMAC_STADAT(); |
| } |
| |
| /* Write an off-chip register in a PHY through the MDC/MDIO port */ |
| static int bfin_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, |
| u16 value) |
| { |
| bfin_mdio_poll(); |
| |
| bfin_write_EMAC_STADAT((u32) value); |
| |
| /* write mode */ |
| bfin_write_EMAC_STAADD(SET_PHYAD((u16) phy_addr) | |
| SET_REGAD((u16) regnum) | |
| STAOP | |
| STABUSY); |
| |
| bfin_mdio_poll(); |
| |
| return 0; |
| } |
| |
| static int bfin_mdiobus_reset(struct mii_bus *bus) |
| { |
| return 0; |
| } |
| |
| static void bfin_mac_adjust_link(struct net_device *dev) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| struct phy_device *phydev = lp->phydev; |
| unsigned long flags; |
| int new_state = 0; |
| |
| spin_lock_irqsave(&lp->lock, flags); |
| if (phydev->link) { |
| /* Now we make sure that we can be in full duplex mode. |
| * If not, we operate in half-duplex mode. */ |
| if (phydev->duplex != lp->old_duplex) { |
| u32 opmode = bfin_read_EMAC_OPMODE(); |
| new_state = 1; |
| |
| if (phydev->duplex) |
| opmode |= FDMODE; |
| else |
| opmode &= ~(FDMODE); |
| |
| bfin_write_EMAC_OPMODE(opmode); |
| lp->old_duplex = phydev->duplex; |
| } |
| |
| if (phydev->speed != lp->old_speed) { |
| #if defined(CONFIG_BFIN_MAC_RMII) |
| u32 opmode = bfin_read_EMAC_OPMODE(); |
| switch (phydev->speed) { |
| case 10: |
| opmode |= RMII_10; |
| break; |
| case 100: |
| opmode &= ~(RMII_10); |
| break; |
| default: |
| printk(KERN_WARNING |
| "%s: Ack! Speed (%d) is not 10/100!\n", |
| DRV_NAME, phydev->speed); |
| break; |
| } |
| bfin_write_EMAC_OPMODE(opmode); |
| #endif |
| |
| new_state = 1; |
| lp->old_speed = phydev->speed; |
| } |
| |
| if (!lp->old_link) { |
| new_state = 1; |
| lp->old_link = 1; |
| } |
| } else if (lp->old_link) { |
| new_state = 1; |
| lp->old_link = 0; |
| lp->old_speed = 0; |
| lp->old_duplex = -1; |
| } |
| |
| if (new_state) { |
| u32 opmode = bfin_read_EMAC_OPMODE(); |
| phy_print_status(phydev); |
| pr_debug("EMAC_OPMODE = 0x%08x\n", opmode); |
| } |
| |
| spin_unlock_irqrestore(&lp->lock, flags); |
| } |
| |
| /* MDC = 2.5 MHz */ |
| #define MDC_CLK 2500000 |
| |
| static int mii_probe(struct net_device *dev) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| struct phy_device *phydev = NULL; |
| unsigned short sysctl; |
| int i; |
| u32 sclk, mdc_div; |
| |
| /* Enable PHY output early */ |
| if (!(bfin_read_VR_CTL() & PHYCLKOE)) |
| bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE); |
| |
| sclk = get_sclk(); |
| mdc_div = ((sclk / MDC_CLK) / 2) - 1; |
| |
| sysctl = bfin_read_EMAC_SYSCTL(); |
| sysctl = (sysctl & ~MDCDIV) | SET_MDCDIV(mdc_div); |
| bfin_write_EMAC_SYSCTL(sysctl); |
| |
| /* search for connect PHY device */ |
| for (i = 0; i < PHY_MAX_ADDR; i++) { |
| struct phy_device *const tmp_phydev = lp->mii_bus->phy_map[i]; |
| |
| if (!tmp_phydev) |
| continue; /* no PHY here... */ |
| |
| phydev = tmp_phydev; |
| break; /* found it */ |
| } |
| |
| /* now we are supposed to have a proper phydev, to attach to... */ |
| if (!phydev) { |
| printk(KERN_INFO "%s: Don't found any phy device at all\n", |
| dev->name); |
| return -ENODEV; |
| } |
| |
| #if defined(CONFIG_BFIN_MAC_RMII) |
| phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link, |
| 0, PHY_INTERFACE_MODE_RMII); |
| #else |
| phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link, |
| 0, PHY_INTERFACE_MODE_MII); |
| #endif |
| |
| if (IS_ERR(phydev)) { |
| printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); |
| return PTR_ERR(phydev); |
| } |
| |
| /* mask with MAC supported features */ |
| phydev->supported &= (SUPPORTED_10baseT_Half |
| | SUPPORTED_10baseT_Full |
| | SUPPORTED_100baseT_Half |
| | SUPPORTED_100baseT_Full |
| | SUPPORTED_Autoneg |
| | SUPPORTED_Pause | SUPPORTED_Asym_Pause |
| | SUPPORTED_MII |
| | SUPPORTED_TP); |
| |
| phydev->advertising = phydev->supported; |
| |
| lp->old_link = 0; |
| lp->old_speed = 0; |
| lp->old_duplex = -1; |
| lp->phydev = phydev; |
| |
| printk(KERN_INFO "%s: attached PHY driver [%s] " |
| "(mii_bus:phy_addr=%s, irq=%d, mdc_clk=%dHz(mdc_div=%d)" |
| "@sclk=%dMHz)\n", |
| DRV_NAME, phydev->drv->name, dev_name(&phydev->dev), phydev->irq, |
| MDC_CLK, mdc_div, sclk/1000000); |
| |
| return 0; |
| } |
| |
| /* |
| * Ethtool support |
| */ |
| |
| static int |
| bfin_mac_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| |
| if (lp->phydev) |
| return phy_ethtool_gset(lp->phydev, cmd); |
| |
| return -EINVAL; |
| } |
| |
| static int |
| bfin_mac_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| |
| if (!capable(CAP_NET_ADMIN)) |
| return -EPERM; |
| |
| if (lp->phydev) |
| return phy_ethtool_sset(lp->phydev, cmd); |
| |
| return -EINVAL; |
| } |
| |
| static void bfin_mac_ethtool_getdrvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| strcpy(info->driver, DRV_NAME); |
| strcpy(info->version, DRV_VERSION); |
| strcpy(info->fw_version, "N/A"); |
| strcpy(info->bus_info, dev_name(&dev->dev)); |
| } |
| |
| static struct ethtool_ops bfin_mac_ethtool_ops = { |
| .get_settings = bfin_mac_ethtool_getsettings, |
| .set_settings = bfin_mac_ethtool_setsettings, |
| .get_link = ethtool_op_get_link, |
| .get_drvinfo = bfin_mac_ethtool_getdrvinfo, |
| }; |
| |
| /**************************************************************************/ |
| void setup_system_regs(struct net_device *dev) |
| { |
| unsigned short sysctl; |
| |
| /* |
| * Odd word alignment for Receive Frame DMA word |
| * Configure checksum support and rcve frame word alignment |
| */ |
| sysctl = bfin_read_EMAC_SYSCTL(); |
| #if defined(BFIN_MAC_CSUM_OFFLOAD) |
| sysctl |= RXDWA | RXCKS; |
| #else |
| sysctl |= RXDWA; |
| #endif |
| bfin_write_EMAC_SYSCTL(sysctl); |
| |
| bfin_write_EMAC_MMC_CTL(RSTC | CROLL); |
| |
| /* Initialize the TX DMA channel registers */ |
| bfin_write_DMA2_X_COUNT(0); |
| bfin_write_DMA2_X_MODIFY(4); |
| bfin_write_DMA2_Y_COUNT(0); |
| bfin_write_DMA2_Y_MODIFY(0); |
| |
| /* Initialize the RX DMA channel registers */ |
| bfin_write_DMA1_X_COUNT(0); |
| bfin_write_DMA1_X_MODIFY(4); |
| bfin_write_DMA1_Y_COUNT(0); |
| bfin_write_DMA1_Y_MODIFY(0); |
| } |
| |
| static void setup_mac_addr(u8 *mac_addr) |
| { |
| u32 addr_low = le32_to_cpu(*(__le32 *) & mac_addr[0]); |
| u16 addr_hi = le16_to_cpu(*(__le16 *) & mac_addr[4]); |
| |
| /* this depends on a little-endian machine */ |
| bfin_write_EMAC_ADDRLO(addr_low); |
| bfin_write_EMAC_ADDRHI(addr_hi); |
| } |
| |
| static int bfin_mac_set_mac_address(struct net_device *dev, void *p) |
| { |
| struct sockaddr *addr = p; |
| if (netif_running(dev)) |
| return -EBUSY; |
| memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); |
| setup_mac_addr(dev->dev_addr); |
| return 0; |
| } |
| |
| static void adjust_tx_list(void) |
| { |
| int timeout_cnt = MAX_TIMEOUT_CNT; |
| |
| if (tx_list_head->status.status_word != 0 |
| && current_tx_ptr != tx_list_head) { |
| goto adjust_head; /* released something, just return; */ |
| } |
| |
| /* |
| * if nothing released, check wait condition |
| * current's next can not be the head, |
| * otherwise the dma will not stop as we want |
| */ |
| if (current_tx_ptr->next->next == tx_list_head) { |
| while (tx_list_head->status.status_word == 0) { |
| udelay(10); |
| if (tx_list_head->status.status_word != 0 |
| || !(bfin_read_DMA2_IRQ_STATUS() & DMA_RUN)) { |
| goto adjust_head; |
| } |
| if (timeout_cnt-- < 0) { |
| printk(KERN_ERR DRV_NAME |
| ": wait for adjust tx list head timeout\n"); |
| break; |
| } |
| } |
| if (tx_list_head->status.status_word != 0) { |
| goto adjust_head; |
| } |
| } |
| |
| return; |
| |
| adjust_head: |
| do { |
| tx_list_head->desc_a.config &= ~DMAEN; |
| tx_list_head->status.status_word = 0; |
| if (tx_list_head->skb) { |
| dev_kfree_skb(tx_list_head->skb); |
| tx_list_head->skb = NULL; |
| } else { |
| printk(KERN_ERR DRV_NAME |
| ": no sk_buff in a transmitted frame!\n"); |
| } |
| tx_list_head = tx_list_head->next; |
| } while (tx_list_head->status.status_word != 0 |
| && current_tx_ptr != tx_list_head); |
| return; |
| |
| } |
| |
| static int bfin_mac_hard_start_xmit(struct sk_buff *skb, |
| struct net_device *dev) |
| { |
| u16 *data; |
| u32 data_align = (unsigned long)(skb->data) & 0x3; |
| current_tx_ptr->skb = skb; |
| |
| if (data_align == 0x2) { |
| /* move skb->data to current_tx_ptr payload */ |
| data = (u16 *)(skb->data) - 1; |
| *data = (u16)(skb->len); |
| current_tx_ptr->desc_a.start_addr = (u32)data; |
| /* this is important! */ |
| blackfin_dcache_flush_range((u32)data, |
| (u32)((u8 *)data + skb->len + 4)); |
| } else { |
| *((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len); |
| memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data, |
| skb->len); |
| current_tx_ptr->desc_a.start_addr = |
| (u32)current_tx_ptr->packet; |
| if (current_tx_ptr->status.status_word != 0) |
| current_tx_ptr->status.status_word = 0; |
| blackfin_dcache_flush_range( |
| (u32)current_tx_ptr->packet, |
| (u32)(current_tx_ptr->packet + skb->len + 2)); |
| } |
| |
| /* make sure the internal data buffers in the core are drained |
| * so that the DMA descriptors are completely written when the |
| * DMA engine goes to fetch them below |
| */ |
| SSYNC(); |
| |
| /* enable this packet's dma */ |
| current_tx_ptr->desc_a.config |= DMAEN; |
| |
| /* tx dma is running, just return */ |
| if (bfin_read_DMA2_IRQ_STATUS() & DMA_RUN) |
| goto out; |
| |
| /* tx dma is not running */ |
| bfin_write_DMA2_NEXT_DESC_PTR(&(current_tx_ptr->desc_a)); |
| /* dma enabled, read from memory, size is 6 */ |
| bfin_write_DMA2_CONFIG(current_tx_ptr->desc_a.config); |
| /* Turn on the EMAC tx */ |
| bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() | TE); |
| |
| out: |
| adjust_tx_list(); |
| current_tx_ptr = current_tx_ptr->next; |
| dev->trans_start = jiffies; |
| dev->stats.tx_packets++; |
| dev->stats.tx_bytes += (skb->len); |
| return 0; |
| } |
| |
| static void bfin_mac_rx(struct net_device *dev) |
| { |
| struct sk_buff *skb, *new_skb; |
| unsigned short len; |
| |
| /* allocate a new skb for next time receive */ |
| skb = current_rx_ptr->skb; |
| new_skb = dev_alloc_skb(PKT_BUF_SZ + NET_IP_ALIGN); |
| if (!new_skb) { |
| printk(KERN_NOTICE DRV_NAME |
| ": rx: low on mem - packet dropped\n"); |
| dev->stats.rx_dropped++; |
| goto out; |
| } |
| /* reserve 2 bytes for RXDWA padding */ |
| skb_reserve(new_skb, NET_IP_ALIGN); |
| current_rx_ptr->skb = new_skb; |
| current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2; |
| |
| /* Invidate the data cache of skb->data range when it is write back |
| * cache. It will prevent overwritting the new data from DMA |
| */ |
| blackfin_dcache_invalidate_range((unsigned long)new_skb->head, |
| (unsigned long)new_skb->end); |
| |
| len = (unsigned short)((current_rx_ptr->status.status_word) & RX_FRLEN); |
| skb_put(skb, len); |
| blackfin_dcache_invalidate_range((unsigned long)skb->head, |
| (unsigned long)skb->tail); |
| |
| skb->protocol = eth_type_trans(skb, dev); |
| #if defined(BFIN_MAC_CSUM_OFFLOAD) |
| skb->csum = current_rx_ptr->status.ip_payload_csum; |
| skb->ip_summed = CHECKSUM_COMPLETE; |
| #endif |
| |
| netif_rx(skb); |
| dev->stats.rx_packets++; |
| dev->stats.rx_bytes += len; |
| current_rx_ptr->status.status_word = 0x00000000; |
| current_rx_ptr = current_rx_ptr->next; |
| |
| out: |
| return; |
| } |
| |
| /* interrupt routine to handle rx and error signal */ |
| static irqreturn_t bfin_mac_interrupt(int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| int number = 0; |
| |
| get_one_packet: |
| if (current_rx_ptr->status.status_word == 0) { |
| /* no more new packet received */ |
| if (number == 0) { |
| if (current_rx_ptr->next->status.status_word != 0) { |
| current_rx_ptr = current_rx_ptr->next; |
| goto real_rx; |
| } |
| } |
| bfin_write_DMA1_IRQ_STATUS(bfin_read_DMA1_IRQ_STATUS() | |
| DMA_DONE | DMA_ERR); |
| return IRQ_HANDLED; |
| } |
| |
| real_rx: |
| bfin_mac_rx(dev); |
| number++; |
| goto get_one_packet; |
| } |
| |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| static void bfin_mac_poll(struct net_device *dev) |
| { |
| disable_irq(IRQ_MAC_RX); |
| bfin_mac_interrupt(IRQ_MAC_RX, dev); |
| enable_irq(IRQ_MAC_RX); |
| } |
| #endif /* CONFIG_NET_POLL_CONTROLLER */ |
| |
| static void bfin_mac_disable(void) |
| { |
| unsigned int opmode; |
| |
| opmode = bfin_read_EMAC_OPMODE(); |
| opmode &= (~RE); |
| opmode &= (~TE); |
| /* Turn off the EMAC */ |
| bfin_write_EMAC_OPMODE(opmode); |
| } |
| |
| /* |
| * Enable Interrupts, Receive, and Transmit |
| */ |
| static void bfin_mac_enable(void) |
| { |
| u32 opmode; |
| |
| pr_debug("%s: %s\n", DRV_NAME, __func__); |
| |
| /* Set RX DMA */ |
| bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a)); |
| bfin_write_DMA1_CONFIG(rx_list_head->desc_a.config); |
| |
| /* Wait MII done */ |
| bfin_mdio_poll(); |
| |
| /* We enable only RX here */ |
| /* ASTP : Enable Automatic Pad Stripping |
| PR : Promiscuous Mode for test |
| PSF : Receive frames with total length less than 64 bytes. |
| FDMODE : Full Duplex Mode |
| LB : Internal Loopback for test |
| RE : Receiver Enable */ |
| opmode = bfin_read_EMAC_OPMODE(); |
| if (opmode & FDMODE) |
| opmode |= PSF; |
| else |
| opmode |= DRO | DC | PSF; |
| opmode |= RE; |
| |
| #if defined(CONFIG_BFIN_MAC_RMII) |
| opmode |= RMII; /* For Now only 100MBit are supported */ |
| #if (defined(CONFIG_BF537) || defined(CONFIG_BF536)) && CONFIG_BF_REV_0_2 |
| opmode |= TE; |
| #endif |
| #endif |
| /* Turn on the EMAC rx */ |
| bfin_write_EMAC_OPMODE(opmode); |
| } |
| |
| /* Our watchdog timed out. Called by the networking layer */ |
| static void bfin_mac_timeout(struct net_device *dev) |
| { |
| pr_debug("%s: %s\n", dev->name, __func__); |
| |
| bfin_mac_disable(); |
| |
| /* reset tx queue */ |
| tx_list_tail = tx_list_head->next; |
| |
| bfin_mac_enable(); |
| |
| /* We can accept TX packets again */ |
| dev->trans_start = jiffies; |
| netif_wake_queue(dev); |
| } |
| |
| static void bfin_mac_multicast_hash(struct net_device *dev) |
| { |
| u32 emac_hashhi, emac_hashlo; |
| struct dev_mc_list *dmi = dev->mc_list; |
| char *addrs; |
| int i; |
| u32 crc; |
| |
| emac_hashhi = emac_hashlo = 0; |
| |
| for (i = 0; i < dev->mc_count; i++) { |
| addrs = dmi->dmi_addr; |
| dmi = dmi->next; |
| |
| /* skip non-multicast addresses */ |
| if (!(*addrs & 1)) |
| continue; |
| |
| crc = ether_crc(ETH_ALEN, addrs); |
| crc >>= 26; |
| |
| if (crc & 0x20) |
| emac_hashhi |= 1 << (crc & 0x1f); |
| else |
| emac_hashlo |= 1 << (crc & 0x1f); |
| } |
| |
| bfin_write_EMAC_HASHHI(emac_hashhi); |
| bfin_write_EMAC_HASHLO(emac_hashlo); |
| |
| return; |
| } |
| |
| /* |
| * This routine will, depending on the values passed to it, |
| * either make it accept multicast packets, go into |
| * promiscuous mode (for TCPDUMP and cousins) or accept |
| * a select set of multicast packets |
| */ |
| static void bfin_mac_set_multicast_list(struct net_device *dev) |
| { |
| u32 sysctl; |
| |
| if (dev->flags & IFF_PROMISC) { |
| printk(KERN_INFO "%s: set to promisc mode\n", dev->name); |
| sysctl = bfin_read_EMAC_OPMODE(); |
| sysctl |= RAF; |
| bfin_write_EMAC_OPMODE(sysctl); |
| } else if (dev->flags & IFF_ALLMULTI) { |
| /* accept all multicast */ |
| sysctl = bfin_read_EMAC_OPMODE(); |
| sysctl |= PAM; |
| bfin_write_EMAC_OPMODE(sysctl); |
| } else if (dev->mc_count) { |
| /* set up multicast hash table */ |
| sysctl = bfin_read_EMAC_OPMODE(); |
| sysctl |= HM; |
| bfin_write_EMAC_OPMODE(sysctl); |
| bfin_mac_multicast_hash(dev); |
| } else { |
| /* clear promisc or multicast mode */ |
| sysctl = bfin_read_EMAC_OPMODE(); |
| sysctl &= ~(RAF | PAM); |
| bfin_write_EMAC_OPMODE(sysctl); |
| } |
| } |
| |
| /* |
| * this puts the device in an inactive state |
| */ |
| static void bfin_mac_shutdown(struct net_device *dev) |
| { |
| /* Turn off the EMAC */ |
| bfin_write_EMAC_OPMODE(0x00000000); |
| /* Turn off the EMAC RX DMA */ |
| bfin_write_DMA1_CONFIG(0x0000); |
| bfin_write_DMA2_CONFIG(0x0000); |
| } |
| |
| /* |
| * Open and Initialize the interface |
| * |
| * Set up everything, reset the card, etc.. |
| */ |
| static int bfin_mac_open(struct net_device *dev) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| int retval; |
| pr_debug("%s: %s\n", dev->name, __func__); |
| |
| /* |
| * Check that the address is valid. If its not, refuse |
| * to bring the device up. The user must specify an |
| * address using ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx |
| */ |
| if (!is_valid_ether_addr(dev->dev_addr)) { |
| printk(KERN_WARNING DRV_NAME ": no valid ethernet hw addr\n"); |
| return -EINVAL; |
| } |
| |
| /* initial rx and tx list */ |
| retval = desc_list_init(); |
| |
| if (retval) |
| return retval; |
| |
| phy_start(lp->phydev); |
| phy_write(lp->phydev, MII_BMCR, BMCR_RESET); |
| setup_system_regs(dev); |
| setup_mac_addr(dev->dev_addr); |
| bfin_mac_disable(); |
| bfin_mac_enable(); |
| pr_debug("hardware init finished\n"); |
| netif_start_queue(dev); |
| netif_carrier_on(dev); |
| |
| return 0; |
| } |
| |
| static const struct net_device_ops bfin_mac_netdev_ops = { |
| .ndo_open = bfin_mac_open, |
| .ndo_stop = bfin_mac_close, |
| .ndo_start_xmit = bfin_mac_hard_start_xmit, |
| .ndo_set_mac_address = bfin_mac_set_mac_address, |
| .ndo_tx_timeout = bfin_mac_timeout, |
| .ndo_set_multicast_list = bfin_mac_set_multicast_list, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_change_mtu = eth_change_mtu, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = bfin_mac_poll, |
| #endif |
| }; |
| |
| /* |
| * |
| * this makes the board clean up everything that it can |
| * and not talk to the outside world. Caused by |
| * an 'ifconfig ethX down' |
| */ |
| static int bfin_mac_close(struct net_device *dev) |
| { |
| struct bfin_mac_local *lp = netdev_priv(dev); |
| pr_debug("%s: %s\n", dev->name, __func__); |
| |
| netif_stop_queue(dev); |
| netif_carrier_off(dev); |
| |
| phy_stop(lp->phydev); |
| phy_write(lp->phydev, MII_BMCR, BMCR_PDOWN); |
| |
| /* clear everything */ |
| bfin_mac_shutdown(dev); |
| |
| /* free the rx/tx buffers */ |
| desc_list_free(); |
| |
| return 0; |
| } |
| |
| static int __devinit bfin_mac_probe(struct platform_device *pdev) |
| { |
| struct net_device *ndev; |
| struct bfin_mac_local *lp; |
| struct platform_device *pd; |
| int rc; |
| |
| ndev = alloc_etherdev(sizeof(struct bfin_mac_local)); |
| if (!ndev) { |
| dev_err(&pdev->dev, "Cannot allocate net device!\n"); |
| return -ENOMEM; |
| } |
| |
| SET_NETDEV_DEV(ndev, &pdev->dev); |
| platform_set_drvdata(pdev, ndev); |
| lp = netdev_priv(ndev); |
| |
| /* Grab the MAC address in the MAC */ |
| *(__le32 *) (&(ndev->dev_addr[0])) = cpu_to_le32(bfin_read_EMAC_ADDRLO()); |
| *(__le16 *) (&(ndev->dev_addr[4])) = cpu_to_le16((u16) bfin_read_EMAC_ADDRHI()); |
| |
| /* probe mac */ |
| /*todo: how to proble? which is revision_register */ |
| bfin_write_EMAC_ADDRLO(0x12345678); |
| if (bfin_read_EMAC_ADDRLO() != 0x12345678) { |
| dev_err(&pdev->dev, "Cannot detect Blackfin on-chip ethernet MAC controller!\n"); |
| rc = -ENODEV; |
| goto out_err_probe_mac; |
| } |
| |
| |
| /* |
| * Is it valid? (Did bootloader initialize it?) |
| * Grab the MAC from the board somehow |
| * this is done in the arch/blackfin/mach-bfxxx/boards/eth_mac.c |
| */ |
| if (!is_valid_ether_addr(ndev->dev_addr)) |
| bfin_get_ether_addr(ndev->dev_addr); |
| |
| /* If still not valid, get a random one */ |
| if (!is_valid_ether_addr(ndev->dev_addr)) |
| random_ether_addr(ndev->dev_addr); |
| |
| setup_mac_addr(ndev->dev_addr); |
| |
| if (!pdev->dev.platform_data) { |
| dev_err(&pdev->dev, "Cannot get platform device bfin_mii_bus!\n"); |
| rc = -ENODEV; |
| goto out_err_probe_mac; |
| } |
| pd = pdev->dev.platform_data; |
| lp->mii_bus = platform_get_drvdata(pd); |
| lp->mii_bus->priv = ndev; |
| |
| rc = mii_probe(ndev); |
| if (rc) { |
| dev_err(&pdev->dev, "MII Probe failed!\n"); |
| goto out_err_mii_probe; |
| } |
| |
| /* Fill in the fields of the device structure with ethernet values. */ |
| ether_setup(ndev); |
| |
| ndev->netdev_ops = &bfin_mac_netdev_ops; |
| ndev->ethtool_ops = &bfin_mac_ethtool_ops; |
| |
| spin_lock_init(&lp->lock); |
| |
| /* now, enable interrupts */ |
| /* register irq handler */ |
| rc = request_irq(IRQ_MAC_RX, bfin_mac_interrupt, |
| IRQF_DISABLED, "EMAC_RX", ndev); |
| if (rc) { |
| dev_err(&pdev->dev, "Cannot request Blackfin MAC RX IRQ!\n"); |
| rc = -EBUSY; |
| goto out_err_request_irq; |
| } |
| |
| rc = register_netdev(ndev); |
| if (rc) { |
| dev_err(&pdev->dev, "Cannot register net device!\n"); |
| goto out_err_reg_ndev; |
| } |
| |
| /* now, print out the card info, in a short format.. */ |
| dev_info(&pdev->dev, "%s, Version %s\n", DRV_DESC, DRV_VERSION); |
| |
| return 0; |
| |
| out_err_reg_ndev: |
| free_irq(IRQ_MAC_RX, ndev); |
| out_err_request_irq: |
| out_err_mii_probe: |
| mdiobus_unregister(lp->mii_bus); |
| mdiobus_free(lp->mii_bus); |
| peripheral_free_list(pin_req); |
| out_err_probe_mac: |
| platform_set_drvdata(pdev, NULL); |
| free_netdev(ndev); |
| |
| return rc; |
| } |
| |
| static int __devexit bfin_mac_remove(struct platform_device *pdev) |
| { |
| struct net_device *ndev = platform_get_drvdata(pdev); |
| struct bfin_mac_local *lp = netdev_priv(ndev); |
| |
| platform_set_drvdata(pdev, NULL); |
| |
| lp->mii_bus->priv = NULL; |
| |
| unregister_netdev(ndev); |
| |
| free_irq(IRQ_MAC_RX, ndev); |
| |
| free_netdev(ndev); |
| |
| peripheral_free_list(pin_req); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int bfin_mac_suspend(struct platform_device *pdev, pm_message_t mesg) |
| { |
| struct net_device *net_dev = platform_get_drvdata(pdev); |
| |
| if (netif_running(net_dev)) |
| bfin_mac_close(net_dev); |
| |
| return 0; |
| } |
| |
| static int bfin_mac_resume(struct platform_device *pdev) |
| { |
| struct net_device *net_dev = platform_get_drvdata(pdev); |
| |
| if (netif_running(net_dev)) |
| bfin_mac_open(net_dev); |
| |
| return 0; |
| } |
| #else |
| #define bfin_mac_suspend NULL |
| #define bfin_mac_resume NULL |
| #endif /* CONFIG_PM */ |
| |
| static int __devinit bfin_mii_bus_probe(struct platform_device *pdev) |
| { |
| struct mii_bus *miibus; |
| int rc, i; |
| |
| /* |
| * We are setting up a network card, |
| * so set the GPIO pins to Ethernet mode |
| */ |
| rc = peripheral_request_list(pin_req, DRV_NAME); |
| if (rc) { |
| dev_err(&pdev->dev, "Requesting peripherals failed!\n"); |
| return rc; |
| } |
| |
| rc = -ENOMEM; |
| miibus = mdiobus_alloc(); |
| if (miibus == NULL) |
| goto out_err_alloc; |
| miibus->read = bfin_mdiobus_read; |
| miibus->write = bfin_mdiobus_write; |
| miibus->reset = bfin_mdiobus_reset; |
| |
| miibus->parent = &pdev->dev; |
| miibus->name = "bfin_mii_bus"; |
| snprintf(miibus->id, MII_BUS_ID_SIZE, "0"); |
| miibus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL); |
| if (miibus->irq == NULL) |
| goto out_err_alloc; |
| for (i = 0; i < PHY_MAX_ADDR; ++i) |
| miibus->irq[i] = PHY_POLL; |
| |
| rc = mdiobus_register(miibus); |
| if (rc) { |
| dev_err(&pdev->dev, "Cannot register MDIO bus!\n"); |
| goto out_err_mdiobus_register; |
| } |
| |
| platform_set_drvdata(pdev, miibus); |
| return 0; |
| |
| out_err_mdiobus_register: |
| mdiobus_free(miibus); |
| out_err_alloc: |
| peripheral_free_list(pin_req); |
| |
| return rc; |
| } |
| |
| static int __devexit bfin_mii_bus_remove(struct platform_device *pdev) |
| { |
| struct mii_bus *miibus = platform_get_drvdata(pdev); |
| platform_set_drvdata(pdev, NULL); |
| mdiobus_unregister(miibus); |
| mdiobus_free(miibus); |
| peripheral_free_list(pin_req); |
| return 0; |
| } |
| |
| static struct platform_driver bfin_mii_bus_driver = { |
| .probe = bfin_mii_bus_probe, |
| .remove = __devexit_p(bfin_mii_bus_remove), |
| .driver = { |
| .name = "bfin_mii_bus", |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static struct platform_driver bfin_mac_driver = { |
| .probe = bfin_mac_probe, |
| .remove = __devexit_p(bfin_mac_remove), |
| .resume = bfin_mac_resume, |
| .suspend = bfin_mac_suspend, |
| .driver = { |
| .name = DRV_NAME, |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static int __init bfin_mac_init(void) |
| { |
| int ret; |
| ret = platform_driver_register(&bfin_mii_bus_driver); |
| if (!ret) |
| return platform_driver_register(&bfin_mac_driver); |
| return -ENODEV; |
| } |
| |
| module_init(bfin_mac_init); |
| |
| static void __exit bfin_mac_cleanup(void) |
| { |
| platform_driver_unregister(&bfin_mac_driver); |
| platform_driver_unregister(&bfin_mii_bus_driver); |
| } |
| |
| module_exit(bfin_mac_cleanup); |
| |