blob: 64c0a41ca0c309c7f020928be2db25f5b0f20425 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,msm8953-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm Technologies, Inc. MSM8953 TLMM block
maintainers:
- Bjorn Andersson <bjorn.andersson@linaro.org>
description: |
This binding describes the Top Level Mode Multiplexer block found in the
MSM8953 platform.
properties:
compatible:
const: qcom,msm8953-pinctrl
reg:
maxItems: 1
interrupts:
description: Specifies the TLMM summary IRQ
maxItems: 1
interrupt-controller: true
'#interrupt-cells':
description:
Specifies the PIN numbers and Flags, as defined in defined in
include/dt-bindings/interrupt-controller/irq.h
const: 2
gpio-controller: true
'#gpio-cells':
description: Specifying the pin number and flags, as defined in
include/dt-bindings/gpio/gpio.h
const: 2
gpio-ranges:
maxItems: 1
#PIN CONFIGURATION NODES
patternProperties:
'-pins$':
type: object
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: "/schemas/pinctrl/pincfg-node.yaml"
properties:
pins:
description:
List of gpio pins affected by the properties specified in this
subnode.
items:
oneOf:
- pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$"
- enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0,
qdsd_data1, qdsd_data2, qdsd_data3 ]
minItems: 1
maxItems: 16
function:
description:
Specify the alternative function to be configured for the specified
pins.
enum: [ accel_int, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1,
atest_char, atest_char0, atest_char1, atest_char2, atest_char3,
atest_gpsadc_dtest0_native, atest_gpsadc_dtest1_native, atest_tsens,
atest_wlan0, atest_wlan1, bimc_dte0, bimc_dte1, blsp1_spi,
blsp3_spi, blsp6_spi, blsp7_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3,
blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_spi1,
blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
blsp_spi8, blsp_uart2, blsp_uart4, blsp_uart5, blsp_uart6, cam0_ldo,
cam1_ldo, cam1_rst, cam1_standby, cam2_rst, cam2_standby, cam3_rst,
cam3_standby, cam_irq, cam_mclk, cap_int, cci_async, cci_i2c,
cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
cdc_pdm0, codec_int1, codec_int2, codec_reset, cri_trng, cri_trng0,
cri_trng1, dac_calib0, dac_calib1, dac_calib10, dac_calib11,
dac_calib12, dac_calib13, dac_calib14, dac_calib15, dac_calib16,
dac_calib17, dac_calib18, dac_calib19, dac_calib2, dac_calib20,
dac_calib21, dac_calib22, dac_calib23, dac_calib24, dac_calib25,
dac_calib3, dac_calib4, dac_calib5, dac_calib6, dac_calib7,
dac_calib8, dac_calib9, dbg_out, ddr_bist, dmic0_clk, dmic0_data,
ebi_cdc, ebi_ch0, ext_lpass, flash_strobe, fp_int, gcc_gp1_clk_a,
gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a,
gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gpio, gsm0_tx, gsm1_tx,
gyro_int, hall_int, hdmi_int, key_focus, key_home, key_snapshot,
key_volp, ldo_en, ldo_update, lpass_slimbus, lpass_slimbus0,
lpass_slimbus1, m_voc, mag_int, mdp_vsync, mipi_dsi0, modem_tsync,
mss_lte, nav_pps, nav_pps_in_a, nav_pps_in_b, nav_tsync,
nfc_disable, nfc_dwl, nfc_irq, ois_sync, pa_indicator, pbs0, pbs1,
pbs2, pressure_int, pri_mi2s, pri_mi2s_mclk_a, pri_mi2s_mclk_b,
pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
pwr_down, pwr_modem_enabled_a, pwr_modem_enabled_b,
pwr_nav_enabled_a, pwr_nav_enabled_b, qdss_cti_trig_in_a0,
qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b,
qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
qdss_tracedata_b, sd_write, sdcard_det, sec_mi2s, sec_mi2s_mclk_a,
sec_mi2s_mclk_b, smb_int, ss_switch, ssbi_wtr1, ts_resout,
ts_sample, ts_xvdd, tsens_max, uim1_clk, uim1_data, uim1_present,
uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan,
wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ]
drive-strength:
enum: [2, 4, 6, 8, 10, 12, 14, 16]
default: 2
description:
Selects the drive strength for the specified pins, in mA.
bias-pull-down: true
bias-pull-up: true
bias-disable: true
output-high: true
output-low: true
required:
- pins
- function
additionalProperties: false
allOf:
- $ref: "pinctrl.yaml#"
required:
- compatible
- reg
- interrupts
- interrupt-controller
- '#interrupt-cells'
- gpio-controller
- '#gpio-cells'
- gpio-ranges
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
tlmm: pinctrl@1000000 {
compatible = "qcom,msm8953-pinctrl";
reg = <0x01000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&tlmm 0 0 142>;
serial_default: serial-pins {
pins = "gpio4", "gpio5";
function = "blsp_uart2";
drive-strength = <2>;
bias-disable;
};
};