| * Texas Instruments CPSW ethernet driver |
| |
| Multiqueue & CBS & MQPRIO |
| ===================================================================== |
| ===================================================================== |
| |
| The cpsw has 3 CBS shapers for each external ports. This document |
| describes MQPRIO and CBS Qdisc offload configuration for cpsw driver |
| based on examples. It potentially can be used in audio video bridging |
| (AVB) and time sensitive networking (TSN). |
| |
| The following examples were tested on AM572x EVM and BBB boards. |
| |
| Test setup |
| ========== |
| |
| Under consideration two examples with AM572x EVM running cpsw driver |
| in dual_emac mode. |
| |
| Several prerequisites: |
| - TX queues must be rated starting from txq0 that has highest priority |
| - Traffic classes are used starting from 0, that has highest priority |
| - CBS shapers should be used with rated queues |
| - The bandwidth for CBS shapers has to be set a little bit more then |
| potential incoming rate, thus, rate of all incoming tx queues has |
| to be a little less |
| - Real rates can differ, due to discreetness |
| - Map skb-priority to txq is not enough, also skb-priority to l2 prio |
| map has to be created with ip or vconfig tool |
| - Any l2/socket prio (0 - 7) for classes can be used, but for |
| simplicity default values are used: 3 and 2 |
| - only 2 classes tested: A and B, but checked and can work with more, |
| maximum allowed 4, but only for 3 rate can be set. |
| |
| Test setup for examples |
| ======================= |
| +-------------------------------+ |
| |--+ | |
| | | Workstation0 | |
| |E | MAC 18:03:73:66:87:42 | |
| +-----------------------------+ +--|t | | |
| | | 1 | E | | |h |./tsn_listener -d \ | |
| | Target board: | 0 | t |--+ |0 | 18:03:73:66:87:42 -i eth0 \| |
| | AM572x EVM | 0 | h | | | -s 1500 | |
| | | 0 | 0 | |--+ | |
| | Only 2 classes: |Mb +---| +-------------------------------+ |
| | class A, class B | | |
| | | +---| +-------------------------------+ |
| | | 1 | E | |--+ | |
| | | 0 | t | | | Workstation1 | |
| | | 0 | h |--+ |E | MAC 20:cf:30:85:7d:fd | |
| | |Mb | 1 | +--|t | | |
| +-----------------------------+ |h |./tsn_listener -d \ | |
| |0 | 20:cf:30:85:7d:fd -i eth0 \| |
| | | -s 1500 | |
| |--+ | |
| +-------------------------------+ |
| |
| ********************************************************************* |
| ********************************************************************* |
| ********************************************************************* |
| Example 1: One port tx AVB configuration scheme for target board |
| ---------------------------------------------------------------------- |
| (prints and scheme for AM572x evm, applicable for single port boards) |
| |
| tc - traffic class |
| txq - transmit queue |
| p - priority |
| f - fifo (cpsw fifo) |
| S - shaper configured |
| |
| +------------------------------------------------------------------+ u |
| | +---------------+ +---------------+ +------+ +------+ | s |
| | | | | | | | | | | e |
| | | App 1 | | App 2 | | Apps | | Apps | | r |
| | | Class A | | Class B | | Rest | | Rest | | |
| | | Eth0 | | Eth0 | | Eth0 | | Eth1 | | s |
| | | VLAN100 | | VLAN100 | | | | | | | | p |
| | | 40 Mb/s | | 20 Mb/s | | | | | | | | a |
| | | SO_PRIORITY=3 | | SO_PRIORITY=2 | | | | | | | | c |
| | | | | | | | | | | | | | | e |
| | +---|-----------+ +---|-----------+ +---|--+ +---|--+ | |
| +-----|------------------|------------------|--------|-------------+ |
| +-+ +------------+ | | |
| | | +-----------------+ +--+ |
| | | | | |
| +---|-------|-------------|-----------------------|----------------+ |
| | +----+ +----+ +----+ +----+ +----+ | |
| | | p3 | | p2 | | p1 | | p0 | | p0 | | k |
| | \ / \ / \ / \ / \ / | e |
| | \ / \ / \ / \ / \ / | r |
| | \/ \/ \/ \/ \/ | n |
| | | | | | | e |
| | | | +-----+ | | l |
| | | | | | | |
| | +----+ +----+ +----+ +----+ | s |
| | |tc0 | |tc1 | |tc2 | |tc0 | | p |
| | \ / \ / \ / \ / | a |
| | \ / \ / \ / \ / | c |
| | \/ \/ \/ \/ | e |
| | | | +-----+ | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | +----+ +----+ +----+ +----+ +----+ | |
| | |txq0| |txq1| |txq2| |txq3| |txq4| | |
| | \ / \ / \ / \ / \ / | |
| | \ / \ / \ / \ / \ / | |
| | \/ \/ \/ \/ \/ | |
| | +-|------|------|------|--+ +--|--------------+ | |
| | | | | | | | Eth0.100 | | Eth1 | | |
| +---|------|------|------|------------------------|----------------+ |
| | | | | | |
| p p p p | |
| 3 2 0-1, 4-7 <- L2 priority | |
| | | | | | |
| | | | | | |
| +---|------|------|------|------------------------|----------------+ |
| | | | | | |----------+ | |
| | +----+ +----+ +----+ +----+ +----+ | |
| | |dma7| |dma6| |dma5| |dma4| |dma3| | |
| | \ / \ / \ / \ / \ / | c |
| | \S / \S / \ / \ / \ / | p |
| | \/ \/ \/ \/ \/ | s |
| | | | | +----- | | w |
| | | | | | | | |
| | | | | | | | d |
| | +----+ +----+ +----+p p+----+ | r |
| | | | | | | |o o| | | i |
| | | f3 | | f2 | | f0 |r r| f0 | | v |
| | |tc0 | |tc1 | |tc2 |t t|tc0 | | e |
| | \CBS / \CBS / \CBS /1 2\CBS / | r |
| | \S / \S / \ / \ / | |
| | \/ \/ \/ \/ | |
| +------------------------------------------------------------------+ |
| ========================================Eth==========================> |
| |
| 1) |
| // Add 4 tx queues, for interface Eth0, and 1 tx queue for Eth1 |
| $ ethtool -L eth0 rx 1 tx 5 |
| rx unmodified, ignoring |
| |
| 2) |
| // Check if num of queues is set correctly: |
| $ ethtool -l eth0 |
| Channel parameters for eth0: |
| Pre-set maximums: |
| RX: 8 |
| TX: 8 |
| Other: 0 |
| Combined: 0 |
| Current hardware settings: |
| RX: 1 |
| TX: 5 |
| Other: 0 |
| Combined: 0 |
| |
| 3) |
| // TX queues must be rated starting from 0, so set bws for tx0 and tx1 |
| // Set rates 40 and 20 Mb/s appropriately. |
| // Pay attention, real speed can differ a bit due to discreetness. |
| // Leave last 2 tx queues not rated. |
| $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate |
| $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate |
| |
| 4) |
| // Check maximum rate of tx (cpdma) queues: |
| $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate |
| 40 |
| 20 |
| 0 |
| 0 |
| 0 |
| |
| 5) |
| // Map skb->priority to traffic class: |
| // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| // Map traffic class to transmit queue: |
| // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq2, txq3) |
| $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ |
| map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 |
| |
| 5a) |
| // As two interface sharing same set of tx queues, assign all traffic |
| // coming to interface Eth1 to separate queue in order to not mix it |
| // with traffic from interface Eth0, so use separate txq to send |
| // packets to Eth1, so all prio -> tc0 and tc0 -> txq4 |
| // Here hw 0, so here still default configuration for eth1 in hw |
| $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 1 \ |
| map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@4 hw 0 |
| |
| 6) |
| // Check classes settings |
| $ tc -g class show dev eth0 |
| +---(100:ffe2) mqprio |
| | +---(100:3) mqprio |
| | +---(100:4) mqprio |
| | |
| +---(100:ffe1) mqprio |
| | +---(100:2) mqprio |
| | |
| +---(100:ffe0) mqprio |
| +---(100:1) mqprio |
| |
| $ tc -g class show dev eth1 |
| +---(100:ffe0) mqprio |
| +---(100:5) mqprio |
| |
| 7) |
| // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc |
| // Set it +1 Mb for reserve (important!) |
| // here only idle slope is important, others arg are ignored |
| // Pay attention, real speed can differ a bit due to discreetness |
| $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1438 \ |
| hicredit 62 sendslope -959000 idleslope 41000 offload 1 |
| net eth0: set FIFO3 bw = 50 |
| |
| 8) |
| // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc: |
| // Set it +1 Mb for reserve (important!) |
| $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1468 \ |
| hicredit 65 sendslope -979000 idleslope 21000 offload 1 |
| net eth0: set FIFO2 bw = 30 |
| |
| 9) |
| // Create vlan 100 to map sk->priority to vlan qos |
| $ ip link add link eth0 name eth0.100 type vlan id 100 |
| 8021q: 802.1Q VLAN Support v1.8 |
| 8021q: adding VLAN 0 to HW filter on device eth0 |
| 8021q: adding VLAN 0 to HW filter on device eth1 |
| net eth0: Adding vlanid 100 to vlan filter |
| |
| 10) |
| // Map skb->priority to L2 prio, 1 to 1 |
| $ ip link set eth0.100 type vlan \ |
| egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 11) |
| // Check egress map for vlan 100 |
| $ cat /proc/net/vlan/eth0.100 |
| [...] |
| INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 12) |
| // Run your appropriate tools with socket option "SO_PRIORITY" |
| // to 3 for class A and/or to 2 for class B |
| // (I took at https://www.spinics.net/lists/netdev/msg460869.html) |
| ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& |
| ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& |
| |
| 13) |
| // run your listener on workstation (should be in same vlan) |
| // (I took at https://www.spinics.net/lists/netdev/msg460869.html) |
| ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39000 kbps |
| |
| 14) |
| // Restore default configuration if needed |
| $ ip link del eth0.100 |
| $ tc qdisc del dev eth1 root |
| $ tc qdisc del dev eth0 root |
| net eth0: Prev FIFO2 is shaped |
| net eth0: set FIFO3 bw = 0 |
| net eth0: set FIFO2 bw = 0 |
| $ ethtool -L eth0 rx 1 tx 1 |
| |
| ********************************************************************* |
| ********************************************************************* |
| ********************************************************************* |
| Example 2: Two port tx AVB configuration scheme for target board |
| ---------------------------------------------------------------------- |
| (prints and scheme for AM572x evm, for dual emac boards only) |
| |
| +------------------------------------------------------------------+ u |
| | +----------+ +----------+ +------+ +----------+ +----------+ | s |
| | | | | | | | | | | | | e |
| | | App 1 | | App 2 | | Apps | | App 3 | | App 4 | | r |
| | | Class A | | Class B | | Rest | | Class B | | Class A | | |
| | | Eth0 | | Eth0 | | | | | Eth1 | | Eth1 | | s |
| | | VLAN100 | | VLAN100 | | | | | VLAN100 | | VLAN100 | | p |
| | | 40 Mb/s | | 20 Mb/s | | | | | 10 Mb/s | | 30 Mb/s | | a |
| | | SO_PRI=3 | | SO_PRI=2 | | | | | SO_PRI=3 | | SO_PRI=2 | | c |
| | | | | | | | | | | | | | | | | | e |
| | +---|------+ +---|------+ +---|--+ +---|------+ +---|------+ | |
| +-----|-------------|-------------|---------|-------------|--------+ |
| +-+ +-------+ | +----------+ +----+ |
| | | +-------+------+ | | |
| | | | | | | |
| +---|-------|-------------|--------------|-------------|-------|---+ |
| | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | |
| | | p3 | | p2 | | p1 | | p0 | | p0 | | p1 | | p2 | | p3 | | k |
| | \ / \ / \ / \ / \ / \ / \ / \ / | e |
| | \ / \ / \ / \ / \ / \ / \ / \ / | r |
| | \/ \/ \/ \/ \/ \/ \/ \/ | n |
| | | | | | | | | e |
| | | | +----+ +----+ | | | l |
| | | | | | | | | |
| | +----+ +----+ +----+ +----+ +----+ +----+ | s |
| | |tc0 | |tc1 | |tc2 | |tc2 | |tc1 | |tc0 | | p |
| | \ / \ / \ / \ / \ / \ / | a |
| | \ / \ / \ / \ / \ / \ / | c |
| | \/ \/ \/ \/ \/ \/ | e |
| | | | +-----+ +-----+ | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | E E | | | | | |
| | +----+ +----+ +----+ +----+ t t +----+ +----+ +----+ +----+ | |
| | |txq0| |txq1| |txq4| |txq5| h h |txq6| |txq7| |txq3| |txq2| | |
| | \ / \ / \ / \ / 0 1 \ / \ / \ / \ / | |
| | \ / \ / \ / \ / . . \ / \ / \ / \ / | |
| | \/ \/ \/ \/ 1 1 \/ \/ \/ \/ | |
| | +-|------|------|------|--+ 0 0 +-|------|------|------|--+ | |
| | | | | | | | 0 0 | | | | | | | |
| +---|------|------|------|---------------|------|------|------|----+ |
| | | | | | | | | |
| p p p p p p p p |
| 3 2 0-1, 4-7 <-L2 pri-> 0-1, 4-7 2 3 |
| | | | | | | | | |
| | | | | | | | | |
| +---|------|------|------|---------------|------|------|------|----+ |
| | | | | | | | | | | |
| | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | |
| | |dma7| |dma6| |dma3| |dma2| |dma1| |dma0| |dma4| |dma5| | |
| | \ / \ / \ / \ / \ / \ / \ / \ / | c |
| | \S / \S / \ / \ / \ / \ / \S / \S / | p |
| | \/ \/ \/ \/ \/ \/ \/ \/ | s |
| | | | | +----- | | | | | w |
| | | | | | +----+ | | | | |
| | | | | | | | | | | d |
| | +----+ +----+ +----+p p+----+ +----+ +----+ | r |
| | | | | | | |o o| | | | | | | i |
| | | f3 | | f2 | | f0 |r CPSW r| f3 | | f2 | | f0 | | v |
| | |tc0 | |tc1 | |tc2 |t t|tc0 | |tc1 | |tc2 | | e |
| | \CBS / \CBS / \CBS /1 2\CBS / \CBS / \CBS / | r |
| | \S / \S / \ / \S / \S / \ / | |
| | \/ \/ \/ \/ \/ \/ | |
| +------------------------------------------------------------------+ |
| ========================================Eth==========================> |
| |
| 1) |
| // Add 8 tx queues, for interface Eth0, but they are common, so are accessed |
| // by two interfaces Eth0 and Eth1. |
| $ ethtool -L eth1 rx 1 tx 8 |
| rx unmodified, ignoring |
| |
| 2) |
| // Check if num of queues is set correctly: |
| $ ethtool -l eth0 |
| Channel parameters for eth0: |
| Pre-set maximums: |
| RX: 8 |
| TX: 8 |
| Other: 0 |
| Combined: 0 |
| Current hardware settings: |
| RX: 1 |
| TX: 8 |
| Other: 0 |
| Combined: 0 |
| |
| 3) |
| // TX queues must be rated starting from 0, so set bws for tx0 and tx1 for Eth0 |
| // and for tx2 and tx3 for Eth1. That is, rates 40 and 20 Mb/s appropriately |
| // for Eth0 and 30 and 10 Mb/s for Eth1. |
| // Real speed can differ a bit due to discreetness |
| // Leave last 4 tx queues as not rated |
| $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate |
| $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate |
| $ echo 30 > /sys/class/net/eth1/queues/tx-2/tx_maxrate |
| $ echo 10 > /sys/class/net/eth1/queues/tx-3/tx_maxrate |
| |
| 4) |
| // Check maximum rate of tx (cpdma) queues: |
| $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate |
| 40 |
| 20 |
| 30 |
| 10 |
| 0 |
| 0 |
| 0 |
| 0 |
| |
| 5) |
| // Map skb->priority to traffic class for Eth0: |
| // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| // Map traffic class to transmit queue: |
| // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq4, txq5) |
| $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ |
| map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@4 hw 1 |
| |
| 6) |
| // Check classes settings |
| $ tc -g class show dev eth0 |
| +---(100:ffe2) mqprio |
| | +---(100:5) mqprio |
| | +---(100:6) mqprio |
| | |
| +---(100:ffe1) mqprio |
| | +---(100:2) mqprio |
| | |
| +---(100:ffe0) mqprio |
| +---(100:1) mqprio |
| |
| 7) |
| // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc for Eth0 |
| // here only idle slope is important, others ignored |
| // Real speed can differ a bit due to discreetness |
| $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1470 \ |
| hicredit 62 sendslope -959000 idleslope 41000 offload 1 |
| net eth0: set FIFO3 bw = 50 |
| |
| 8) |
| // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc for Eth0 |
| $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \ |
| hicredit 65 sendslope -979000 idleslope 21000 offload 1 |
| net eth0: set FIFO2 bw = 30 |
| |
| 9) |
| // Create vlan 100 to map sk->priority to vlan qos for Eth0 |
| $ ip link add link eth0 name eth0.100 type vlan id 100 |
| net eth0: Adding vlanid 100 to vlan filter |
| |
| 10) |
| // Map skb->priority to L2 prio for Eth0.100, one to one |
| $ ip link set eth0.100 type vlan \ |
| egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 11) |
| // Check egress map for vlan 100 |
| $ cat /proc/net/vlan/eth0.100 |
| [...] |
| INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 12) |
| // Map skb->priority to traffic class for Eth1: |
| // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| // Map traffic class to transmit queue: |
| // tc0 -> txq2, tc1 -> txq3, tc2 -> (txq6, txq7) |
| $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 3 \ |
| map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@2 1@3 2@6 hw 1 |
| |
| 13) |
| // Check classes settings |
| $ tc -g class show dev eth1 |
| +---(100:ffe2) mqprio |
| | +---(100:7) mqprio |
| | +---(100:8) mqprio |
| | |
| +---(100:ffe1) mqprio |
| | +---(100:4) mqprio |
| | |
| +---(100:ffe0) mqprio |
| +---(100:3) mqprio |
| |
| 14) |
| // Set rate for class A - 31 Mbit (tc0, txq2) using CBS Qdisc for Eth1 |
| // here only idle slope is important, others ignored |
| // Set it +1 Mb for reserve (important!) |
| $ tc qdisc add dev eth1 parent 100:3 cbs locredit -1453 \ |
| hicredit 47 sendslope -969000 idleslope 31000 offload 1 |
| net eth1: set FIFO3 bw = 31 |
| |
| 15) |
| // Set rate for class B - 11 Mbit (tc1, txq3) using CBS Qdisc for Eth1 |
| // Set it +1 Mb for reserve (important!) |
| $ tc qdisc add dev eth1 parent 100:4 cbs locredit -1483 \ |
| hicredit 34 sendslope -989000 idleslope 11000 offload 1 |
| net eth1: set FIFO2 bw = 11 |
| |
| 16) |
| // Create vlan 100 to map sk->priority to vlan qos for Eth1 |
| $ ip link add link eth1 name eth1.100 type vlan id 100 |
| net eth1: Adding vlanid 100 to vlan filter |
| |
| 17) |
| // Map skb->priority to L2 prio for Eth1.100, one to one |
| $ ip link set eth1.100 type vlan \ |
| egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 18) |
| // Check egress map for vlan 100 |
| $ cat /proc/net/vlan/eth1.100 |
| [...] |
| INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| |
| 19) |
| // Run appropriate tools with socket option "SO_PRIORITY" to 3 |
| // for class A and to 2 for class B. For both interfaces |
| ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& |
| ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& |
| ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p2 -s 1500& |
| ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p3 -s 1500& |
| |
| 20) |
| // run your listener on workstation (should be in same vlan) |
| // (I took at https://www.spinics.net/lists/netdev/msg460869.html) |
| ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39012 kbps |
| Receiving data rate: 39000 kbps |
| |
| 21) |
| // Restore default configuration if needed |
| $ ip link del eth1.100 |
| $ ip link del eth0.100 |
| $ tc qdisc del dev eth1 root |
| net eth1: Prev FIFO2 is shaped |
| net eth1: set FIFO3 bw = 0 |
| net eth1: set FIFO2 bw = 0 |
| $ tc qdisc del dev eth0 root |
| net eth0: Prev FIFO2 is shaped |
| net eth0: set FIFO3 bw = 0 |
| net eth0: set FIFO2 bw = 0 |
| $ ethtool -L eth0 rx 1 tx 1 |
