blob: f9c07710478d9cfe4de4d451bd52774ad06a04c1 [file] [log] [blame]
This document describes the device tree bindings associated with the
keystone network coprocessor(NetCP) driver support.
The network coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator (SA)
capable of performing IPSec operations on ingress/egress packets.
Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
per Ethernet port.
Keystone NetCP driver has a plug-in module architecture where each of the NetCP
sub-modules exist as a loadable kernel module which plug in to the netcp core.
These sub-modules are represented as "netcp-devices" in the dts bindings. It is
mandatory to have the ethernet switch sub-module for the ethernet interface to
be operational. Any other sub-module like the PA is optional.
NetCP Ethernet SubSystem Layout:
-----------------------------
NetCP subsystem(10G or 1G)
-----------------------------
|
|-> NetCP Devices -> |
| |-> GBE/XGBE Switch
| |
| |-> Packet Accelerator
| |
| |-> Security Accelerator
|
|
|
|-> NetCP Interfaces -> |
|-> Ethernet Port 0
|
|-> Ethernet Port 1
|
|-> Ethernet Port 2
|
|-> Ethernet Port 3
NetCP subsystem properties:
Required properties:
- compatible: Should be "ti,netcp-1.0"
- clocks: phandle to the reference clocks for the subsystem.
- dma-id: Navigator packet dma instance id.
Optional properties:
- reg: register location and the size for the following register
regions in the specified order.
- Efuse MAC address register
- dma-coherent: Present if dma operations are coherent
- big-endian: Keystone devices can be operated in a mode where the DSP is in
the big endian mode. In such cases enable this option. This
option should also be enabled if the ARM is operated in
big endian mode with the DSP in little endian.
NetCP device properties: Device specification for NetCP sub-modules.
1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications.
Required properties:
- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb.
- reg: register location and the size for the following register
regions in the specified order.
- subsystem registers
- serdes registers
- tx-channel: the navigator packet dma channel name for tx.
- tx-queue: the navigator queue number associated with the tx dma channel.
- interfaces: specification for each of the switch port to be registered as a
network interface in the stack.
-- slave-port: Switch port number, 0 based numbering.
-- link-interface: type of link interface, supported options are
- mac<->mac auto negotiate mode: 0
- mac<->phy mode: 1
- mac<->mac forced mode: 2
- mac<->fiber mode: 3
- mac<->phy mode with no mdio: 4
- 10Gb mac<->phy mode : 10
- 10Gb mac<->mac forced mode : 11
----phy-handle: phandle to PHY device
Optional properties:
- enable-ale: NetCP driver keeps the address learning feature in the ethernet
switch module disabled. This attribute is to enable the address
learning.
- secondary-slave-ports: specification for each of the switch port not be
registered as a network interface. NetCP driver
will only initialize these ports and attach PHY
driver to them if needed.
NetCP interface properties: Interface specification for NetCP sub-modules.
Required properties:
- rx-channel: the navigator packet dma channel name for rx.
- rx-queue: the navigator queue number associated with rx dma channel.
- rx-pool: specifies the number of descriptors to be used & the region-id
for creating the rx descriptor pool.
- tx-pool: specifies the number of descriptors to be used & the region-id
for creating the tx descriptor pool.
- rx-queue-depth: number of descriptors in each of the free descriptor
queue (FDQ) for the pktdma Rx flow. There can be at
present a maximum of 4 queues per Rx flow.
- rx-buffer-size: the buffer size for each of the Rx flow FDQ.
- tx-completion-queue: the navigator queue number where the descriptors are
recycled after Tx DMA completion.
Optional properties:
- efuse-mac: If this is 1, then the MAC address for the interface is
obtained from the device efuse mac address register
- local-mac-address: the driver is designed to use the of_get_mac_address api
only if efuse-mac is 0. When efuse-mac is 0, the MAC
address is obtained from local-mac-address. If this
attribute is not present, then the driver will use a
random MAC address.
- "netcp-device label": phandle to the device specification for each of NetCP
sub-module attached to this interface.
Example binding:
netcp: netcp@2090000 {
reg = <0x2620110 0x8>;
reg-names = "efuse";
compatible = "ti,netcp-1.0";
#address-cells = <1>;
#size-cells = <1>;
ranges;
clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
dma-coherent;
/* big-endian; */
dma-id = <0>;
netcp-devices {
#address-cells = <1>;
#size-cells = <1>;
ranges;
gbe@0x2090000 {
label = "netcp-gbe";
reg = <0x2090000 0xf00>;
/* enable-ale; */
tx-queue = <648>;
tx-channel = <8>;
interfaces {
gbe0: interface-0 {
slave-port = <0>;
link-interface = <4>;
};
gbe1: interface-1 {
slave-port = <1>;
link-interface = <4>;
};
};
secondary-slave-ports {
port-2 {
slave-port = <2>;
link-interface = <2>;
};
port-3 {
slave-port = <3>;
link-interface = <2>;
};
};
};
};
netcp-interfaces {
interface-0 {
rx-channel = <22>;
rx-pool = <1024 12>;
tx-pool = <1024 12>;
rx-queue-depth = <128 128 0 0>;
rx-buffer-size = <1518 4096 0 0>;
rx-queue = <8704>;
tx-completion-queue = <8706>;
efuse-mac = <1>;
netcp-gbe = <&gbe0>;
};
interface-1 {
rx-channel = <23>;
rx-pool = <1024 12>;
tx-pool = <1024 12>;
rx-queue-depth = <128 128 0 0>;
rx-buffer-size = <1518 4096 0 0>;
rx-queue = <8705>;
tx-completion-queue = <8707>;
efuse-mac = <0>;
local-mac-address = [02 18 31 7e 3e 6f];
netcp-gbe = <&gbe1>;
};
};
};