blob: a5943f51e8c25b1fe26f2957236b39f0e05ac436 [file] [log] [blame]
// SPDX-License-Identifier: ISC
/*
* Device Tree file for the Gateworks Avila GW2348 board.
* This machine is based on IXP425.
*/
/dts-v1/;
#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Gateworks Avila GW2348";
compatible = "gateworks,gw2348", "intel,ixp42x";
#address-cells = <1>;
#size-cells = <1>;
memory@0 {
device_type = "memory";
reg = <0x00000000 0x4000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8";
stdout-path = "uart0:115200n8";
};
aliases {
serial0 = &uart0;
};
leds {
compatible = "gpio-leds";
led-user {
label = "gw2348:green:user";
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
hwmon@28 {
compatible = "adi,ad7418";
reg = <0x28>;
};
rtc: ds1672@68 {
compatible = "dallas,ds1672";
reg = <0x68>;
};
eeprom@51 {
compatible = "atmel,24c08";
reg = <0x51>;
pagesize = <16>;
size = <1024>;
read-only;
};
};
soc {
bus@c4000000 {
flash@0,0 {
compatible = "intel,ixp4xx-flash", "cfi-flash";
bank-width = <2>;
/* Enable writes on the expansion bus */
intel,ixp4xx-eb-write-enable = <1>;
/* 16 MB of Flash mapped in at CS0 */
reg = <0 0x00000000 0x1000000>;
partitions {
compatible = "redboot-fis";
/* Eraseblock at 0x0fe0000 */
fis-index-block = <0x7f>;
};
};
ide@1,0 {
compatible = "intel,ixp4xx-compact-flash";
/*
* Set up expansion bus config to a really slow timing.
* The CF driver will dynamically reconfigure these timings
* depending on selected PIO mode (0-4).
*/
intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase
intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase
intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
intel,ixp4xx-eb-byte-access-on-halfword = <1>;
intel,ixp4xx-eb-mux-address-and-data = <0>;
intel,ixp4xx-eb-ahb-split-transfers = <0>;
intel,ixp4xx-eb-write-enable = <1>;
intel,ixp4xx-eb-byte-access = <1>;
/* First register set is CMD second is CTL (notice it uses CS2) */
reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>;
interrupt-parent = <&gpio0>;
interrupts = <12 IRQ_TYPE_EDGE_RISING>;
};
/*
* FIXME: Latch LEDs or extra UARTs at CS4
*/
};
pci@c0000000 {
status = "ok";
/*
* Taken from Avila PCI boardfile.
*
* We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
*/
#interrupt-cells = <1>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map =
/* IDSEL 1 */
<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
<0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
/* IDSEL 2 */
<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
<0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
/* IDSEL 3 */
<0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
<0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
/* IDSEL 4 */
<0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
<0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
};
/* EthB */
ethernet@c8009000 {
status = "ok";
queue-rx = <&qmgr 3>;
queue-txready = <&qmgr 20>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
/* EthC */
ethernet@c800a000 {
status = "ok";
queue-rx = <&qmgr 4>;
queue-txready = <&qmgr 21>;
phy-mode = "rgmii";
phy-handle = <&phy1>;
};
};
};