| // SPDX-License-Identifier: GPL-2.0-or-later |
| // Copyright 2019 IBM Corp. |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/aspeed-scu-ic.h> |
| #include <dt-bindings/clock/ast2600-clock.h> |
| |
| / { |
| model = "Aspeed BMC"; |
| compatible = "aspeed,ast2600"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| i2c6 = &i2c6; |
| i2c7 = &i2c7; |
| i2c8 = &i2c8; |
| i2c9 = &i2c9; |
| i2c10 = &i2c10; |
| i2c11 = &i2c11; |
| i2c12 = &i2c12; |
| i2c13 = &i2c13; |
| i2c14 = &i2c14; |
| i2c15 = &i2c15; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &vuart1; |
| serial6 = &vuart2; |
| }; |
| |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "aspeed,ast2600-smp"; |
| |
| cpu@f00 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0xf00>; |
| }; |
| |
| cpu@f01 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0xf01>; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; |
| clocks = <&syscon ASPEED_CLK_HPLL>; |
| arm,cpu-registers-not-fw-configured; |
| always-on; |
| }; |
| |
| ahb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| device_type = "soc"; |
| ranges; |
| |
| gic: interrupt-controller@40461000 { |
| compatible = "arm,cortex-a7-gic"; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupt-parent = <&gic>; |
| reg = <0x40461000 0x1000>, |
| <0x40462000 0x1000>, |
| <0x40464000 0x2000>, |
| <0x40466000 0x2000>; |
| }; |
| |
| fmc: spi@1e620000 { |
| reg = < 0x1e620000 0xc4 |
| 0x20000000 0x10000000 >; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-fmc"; |
| clocks = <&syscon ASPEED_CLK_AHB>; |
| status = "disabled"; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| flash@0 { |
| reg = < 0 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| flash@1 { |
| reg = < 1 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| flash@2 { |
| reg = < 2 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi1: spi@1e630000 { |
| reg = < 0x1e630000 0xc4 |
| 0x30000000 0x10000000 >; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-spi"; |
| clocks = <&syscon ASPEED_CLK_AHB>; |
| status = "disabled"; |
| flash@0 { |
| reg = < 0 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| flash@1 { |
| reg = < 1 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi2: spi@1e631000 { |
| reg = < 0x1e631000 0xc4 |
| 0x50000000 0x10000000 >; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-spi"; |
| clocks = <&syscon ASPEED_CLK_AHB>; |
| status = "disabled"; |
| flash@0 { |
| reg = < 0 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| flash@1 { |
| reg = < 1 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| flash@2 { |
| reg = < 2 >; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| mdio0: mdio@1e650000 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x1e650000 0x8>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio1_default>; |
| }; |
| |
| mdio1: mdio@1e650008 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x1e650008 0x8>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio2_default>; |
| }; |
| |
| mdio2: mdio@1e650010 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x1e650010 0x8>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio3_default>; |
| }; |
| |
| mdio3: mdio@1e650018 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x1e650018 0x8>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio4_default>; |
| }; |
| |
| mac0: ftgmac@1e660000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e660000 0x180>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>; |
| status = "disabled"; |
| }; |
| |
| mac1: ftgmac@1e680000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e680000 0x180>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>; |
| status = "disabled"; |
| }; |
| |
| mac2: ftgmac@1e670000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e670000 0x180>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>; |
| status = "disabled"; |
| }; |
| |
| mac3: ftgmac@1e690000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e690000 0x180>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>; |
| status = "disabled"; |
| }; |
| |
| ehci0: usb@1e6a1000 { |
| compatible = "aspeed,ast2600-ehci", "generic-ehci"; |
| reg = <0x1e6a1000 0x100>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2ah_default>; |
| status = "disabled"; |
| }; |
| |
| ehci1: usb@1e6a3000 { |
| compatible = "aspeed,ast2600-ehci", "generic-ehci"; |
| reg = <0x1e6a3000 0x100>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2bh_default>; |
| status = "disabled"; |
| }; |
| |
| uhci: usb@1e6b0000 { |
| compatible = "aspeed,ast2600-uhci", "generic-uhci"; |
| reg = <0x1e6b0000 0x100>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| #ports = <2>; |
| clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>; |
| status = "disabled"; |
| /* |
| * No default pinmux, it will follow EHCI, use an |
| * explicit pinmux override if EHCI is not enabled. |
| */ |
| }; |
| |
| vhub: usb-vhub@1e6a0000 { |
| compatible = "aspeed,ast2600-usb-vhub"; |
| reg = <0x1e6a0000 0x350>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>; |
| aspeed,vhub-downstream-ports = <7>; |
| aspeed,vhub-generic-endpoints = <21>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2ad_default>; |
| status = "disabled"; |
| }; |
| |
| apb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| syscon: syscon@1e6e2000 { |
| compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd"; |
| reg = <0x1e6e2000 0x1000>; |
| ranges = <0 0x1e6e2000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| |
| pinctrl: pinctrl { |
| compatible = "aspeed,ast2600-pinctrl"; |
| }; |
| |
| smp-memram@180 { |
| compatible = "aspeed,ast2600-smpmem"; |
| reg = <0x180 0x40>; |
| }; |
| |
| scu_ic0: interrupt-controller@560 { |
| #interrupt-cells = <1>; |
| compatible = "aspeed,ast2600-scu-ic0"; |
| reg = <0x560 0x4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| }; |
| |
| scu_ic1: interrupt-controller@570 { |
| #interrupt-cells = <1>; |
| compatible = "aspeed,ast2600-scu-ic1"; |
| reg = <0x570 0x4>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| }; |
| }; |
| |
| rng: hwrng@1e6e2524 { |
| compatible = "timeriomem_rng"; |
| reg = <0x1e6e2524 0x4>; |
| period = <1>; |
| quality = <100>; |
| }; |
| |
| xdma: xdma@1e6e7000 { |
| compatible = "aspeed,ast2600-xdma"; |
| reg = <0x1e6e7000 0x100>; |
| clocks = <&syscon ASPEED_CLK_GATE_BCLK>; |
| resets = <&syscon ASPEED_RESET_DEV_XDMA>, <&syscon ASPEED_RESET_RC_XDMA>; |
| reset-names = "device", "root-complex"; |
| interrupts-extended = <&gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, |
| <&scu_ic0 ASPEED_AST2600_SCU_IC0_PCIE_PERST_LO_TO_HI>; |
| aspeed,pcie-device = "bmc"; |
| aspeed,scu = <&syscon>; |
| status = "disabled"; |
| }; |
| |
| gpio0: gpio@1e780000 { |
| #gpio-cells = <2>; |
| gpio-controller; |
| compatible = "aspeed,ast2600-gpio"; |
| reg = <0x1e780000 0x400>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-ranges = <&pinctrl 0 0 208>; |
| ngpios = <208>; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio@1e780800 { |
| #gpio-cells = <2>; |
| gpio-controller; |
| compatible = "aspeed,ast2600-gpio"; |
| reg = <0x1e780800 0x800>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-ranges = <&pinctrl 0 208 36>; |
| ngpios = <36>; |
| clocks = <&syscon ASPEED_CLK_APB1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| rtc: rtc@1e781000 { |
| compatible = "aspeed,ast2600-rtc"; |
| reg = <0x1e781000 0x18>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| timer: timer@1e782000 { |
| compatible = "aspeed,ast2600-timer"; |
| reg = <0x1e782000 0x90>; |
| interrupts-extended = <&gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>, |
| <&gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_APB1>; |
| clock-names = "PCLK"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@1e783000 { |
| compatible = "ns16550a"; |
| reg = <0x1e783000 0x20>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_UART1CLK>; |
| resets = <&lpc_reset 4>; |
| no-loopback-test; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_txd1_default &pinctrl_rxd1_default>; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@1e784000 { |
| compatible = "ns16550a"; |
| reg = <0x1e784000 0x1000>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_UART5CLK>; |
| no-loopback-test; |
| }; |
| |
| wdt1: watchdog@1e785000 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785000 0x40>; |
| }; |
| |
| wdt2: watchdog@1e785040 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785040 0x40>; |
| status = "disabled"; |
| }; |
| |
| wdt3: watchdog@1e785080 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785080 0x40>; |
| status = "disabled"; |
| }; |
| |
| wdt4: watchdog@1e7850c0 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e7850C0 0x40>; |
| status = "disabled"; |
| }; |
| |
| lpc: lpc@1e789000 { |
| compatible = "aspeed,ast2600-lpc", "simple-mfd"; |
| reg = <0x1e789000 0x1000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x1e789000 0x1000>; |
| |
| lpc_bmc: lpc-bmc@0 { |
| compatible = "aspeed,ast2600-lpc-bmc", "simple-mfd", "syscon"; |
| reg = <0x0 0x80>; |
| reg-io-width = <4>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x80>; |
| |
| kcs1: kcs@24 { |
| compatible = "aspeed,ast2500-kcs-bmc-v2"; |
| reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>; |
| interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| kcs_chan = <1>; |
| status = "disabled"; |
| }; |
| kcs2: kcs@28 { |
| compatible = "aspeed,ast2500-kcs-bmc-v2"; |
| reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>; |
| interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| kcs3: kcs@2c { |
| compatible = "aspeed,ast2500-kcs-bmc-v2"; |
| reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lpc_host: lpc-host@80 { |
| compatible = "aspeed,ast2600-lpc-host", "simple-mfd", "syscon"; |
| reg = <0x80 0x1e0>; |
| reg-io-width = <4>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x80 0x1e0>; |
| |
| kcs4: kcs@94 { |
| compatible = "aspeed,ast2500-kcs-bmc-v2"; |
| reg = <0x94 0x1>, <0x98 0x1>, <0x9c 0x1>; |
| interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| lpc_ctrl: lpc-ctrl@0 { |
| compatible = "aspeed,ast2600-lpc-ctrl"; |
| reg = <0x0 0x80>; |
| clocks = <&syscon ASPEED_CLK_GATE_LCLK>; |
| status = "disabled"; |
| }; |
| |
| lpc_snoop: lpc-snoop@0 { |
| compatible = "aspeed,ast2600-lpc-snoop"; |
| reg = <0x0 0x80>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_LCLK>; |
| status = "disabled"; |
| }; |
| |
| lhc: lhc@20 { |
| compatible = "aspeed,ast2600-lhc"; |
| reg = <0x20 0x24 0x48 0x8>; |
| }; |
| |
| lpc_reset: reset-controller@18 { |
| compatible = "aspeed,ast2600-lpc-reset"; |
| reg = <0x18 0x4>; |
| #reset-cells = <1>; |
| }; |
| |
| ibt: ibt@c0 { |
| compatible = "aspeed,ast2600-ibt-bmc"; |
| reg = <0xc0 0x18>; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| sdc: sdc@1e740000 { |
| compatible = "aspeed,ast2600-sd-controller"; |
| reg = <0x1e740000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e740000 0x10000>; |
| clocks = <&syscon ASPEED_CLK_GATE_SDCLK>; |
| status = "disabled"; |
| |
| sdhci0: sdhci@1e740100 { |
| compatible = "aspeed,ast2600-sdhci", "sdhci"; |
| reg = <0x100 0x100>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| sdhci,auto-cmd12; |
| clocks = <&syscon ASPEED_CLK_SDIO>; |
| status = "disabled"; |
| }; |
| |
| sdhci1: sdhci@1e740200 { |
| compatible = "aspeed,ast2600-sdhci", "sdhci"; |
| reg = <0x200 0x100>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| sdhci,auto-cmd12; |
| clocks = <&syscon ASPEED_CLK_SDIO>; |
| status = "disabled"; |
| }; |
| }; |
| |
| emmc_controller: sdc@1e750000 { |
| compatible = "aspeed,ast2600-sd-controller"; |
| reg = <0x1e750000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e750000 0x10000>; |
| clocks = <&syscon ASPEED_CLK_GATE_EMMCCLK>; |
| status = "disabled"; |
| |
| emmc: sdhci@1e750100 { |
| compatible = "aspeed,ast2600-sdhci"; |
| reg = <0x100 0x100>; |
| sdhci,auto-cmd12; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_EMMC>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_emmc_default>; |
| }; |
| }; |
| |
| vuart1: serial@1e787000 { |
| compatible = "aspeed,ast2500-vuart"; |
| reg = <0x1e787000 0x40>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_APB1>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| vuart2: serial@1e788000 { |
| compatible = "aspeed,ast2500-vuart"; |
| reg = <0x1e788000 0x40>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_APB1>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@1e78d000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78d000 0x20>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_UART2CLK>; |
| resets = <&lpc_reset 5>; |
| no-loopback-test; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@1e78e000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78e000 0x20>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_UART3CLK>; |
| resets = <&lpc_reset 6>; |
| no-loopback-test; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@1e78f000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78f000 0x20>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&syscon ASPEED_CLK_GATE_UART4CLK>; |
| resets = <&lpc_reset 7>; |
| no-loopback-test; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_txd4_default &pinctrl_rxd4_default>; |
| status = "disabled"; |
| }; |
| |
| i2c: bus@1e78a000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e78a000 0x1000>; |
| }; |
| |
| fsim0: fsi@1e79b000 { |
| compatible = "aspeed,ast2600-fsi-master", "fsi-master"; |
| reg = <0x1e79b000 0x94>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fsi1_default>; |
| clocks = <&syscon ASPEED_CLK_GATE_FSICLK>; |
| status = "disabled"; |
| }; |
| |
| fsim1: fsi@1e79b100 { |
| compatible = "aspeed,ast2600-fsi-master", "fsi-master"; |
| reg = <0x1e79b100 0x94>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fsi2_default>; |
| clocks = <&syscon ASPEED_CLK_GATE_FSICLK>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| }; |
| |
| #include "aspeed-g6-pinctrl.dtsi" |
| |
| &i2c { |
| i2c0: i2c-bus@80 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x80 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1_default>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c-bus@100 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x100 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2_default>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c-bus@180 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x180 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3_default>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c-bus@200 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x200 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c4_default>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c-bus@280 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x280 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c5_default>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c-bus@300 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x300 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c6_default>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c-bus@380 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x380 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c7_default>; |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c-bus@400 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x400 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c8_default>; |
| status = "disabled"; |
| }; |
| |
| i2c8: i2c-bus@480 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x480 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c9_default>; |
| status = "disabled"; |
| }; |
| |
| i2c9: i2c-bus@500 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x500 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c10_default>; |
| status = "disabled"; |
| }; |
| |
| i2c10: i2c-bus@580 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x580 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c11_default>; |
| status = "disabled"; |
| }; |
| |
| i2c11: i2c-bus@600 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x600 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c12_default>; |
| status = "disabled"; |
| }; |
| |
| i2c12: i2c-bus@680 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x680 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c13_default>; |
| status = "disabled"; |
| }; |
| |
| i2c13: i2c-bus@700 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x700 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c14_default>; |
| status = "disabled"; |
| }; |
| |
| i2c14: i2c-bus@780 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x780 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c15_default>; |
| status = "disabled"; |
| }; |
| |
| i2c15: i2c-bus@800 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x800 0x80>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| clocks = <&syscon ASPEED_CLK_APB2>; |
| resets = <&syscon ASPEED_RESET_I2C>; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; |
| bus-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c16_default>; |
| status = "disabled"; |
| }; |
| }; |
