| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2019 NXP |
| */ |
| |
| #include <dt-bindings/clock/imx8mp-clock.h> |
| #include <dt-bindings/power/imx8mp-power.h> |
| #include <dt-bindings/reset/imx8mp-reset.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interconnect/fsl,imx8mp.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| #include "imx8mp-pinfunc.h" |
| |
| / { |
| interrupt-parent = <&gic>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| ethernet0 = &fec; |
| ethernet1 = &eqos; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| i2c4 = &i2c5; |
| i2c5 = &i2c6; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| mmc2 = &usdhc3; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| spi0 = &flexspi; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| A53_0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| clock-latency = <61036>; |
| clocks = <&clk IMX8MP_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| nvmem-cells = <&cpu_speed_grade>; |
| nvmem-cell-names = "speed_grade"; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x1>; |
| clock-latency = <61036>; |
| clocks = <&clk IMX8MP_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x2>; |
| clock-latency = <61036>; |
| clocks = <&clk IMX8MP_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x3>; |
| clock-latency = <61036>; |
| clocks = <&clk IMX8MP_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_L2: l2-cache0 { |
| compatible = "cache"; |
| cache-unified; |
| cache-level = <2>; |
| cache-size = <0x80000>; |
| cache-line-size = <64>; |
| cache-sets = <512>; |
| }; |
| }; |
| |
| a53_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| opp-microvolt = <850000>; |
| opp-supported-hw = <0x8a0>, <0x7>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1600000000 { |
| opp-hz = /bits/ 64 <1600000000>; |
| opp-microvolt = <950000>; |
| opp-supported-hw = <0xa0>, <0x7>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1800000000 { |
| opp-hz = /bits/ 64 <1800000000>; |
| opp-microvolt = <1000000>; |
| opp-supported-hw = <0x20>, <0x3>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| }; |
| |
| osc_32k: clock-osc-32k { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "osc_32k"; |
| }; |
| |
| osc_24m: clock-osc-24m { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "osc_24m"; |
| }; |
| |
| clk_ext1: clock-ext1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext1"; |
| }; |
| |
| clk_ext2: clock-ext2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext2"; |
| }; |
| |
| clk_ext3: clock-ext3 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext3"; |
| }; |
| |
| clk_ext4: clock-ext4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext4"; |
| }; |
| |
| funnel { |
| /* |
| * non-configurable funnel don't show up on the AMBA |
| * bus. As such no need to add "arm,primecell". |
| */ |
| compatible = "arm,coresight-static-funnel"; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| ca_funnel_in_port0: endpoint { |
| remote-endpoint = <&etm0_out_port>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| ca_funnel_in_port1: endpoint { |
| remote-endpoint = <&etm1_out_port>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| ca_funnel_in_port2: endpoint { |
| remote-endpoint = <&etm2_out_port>; |
| }; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| |
| ca_funnel_in_port3: endpoint { |
| remote-endpoint = <&etm3_out_port>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| |
| ca_funnel_out_port0: endpoint { |
| remote-endpoint = <&hugo_funnel_in_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| dsp_reserved: dsp@92400000 { |
| reg = <0 0x92400000 0 0x2000000>; |
| no-map; |
| status = "disabled"; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a53-pmu"; |
| interrupts = <GIC_PPI 7 |
| (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| thermal-zones { |
| cpu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tmu 0>; |
| trips { |
| cpu_alert0: trip0 { |
| temperature = <85000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu_crit0: trip1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu_alert0>; |
| cooling-device = |
| <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| soc-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tmu 1>; |
| trips { |
| soc_alert0: trip0 { |
| temperature = <85000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| soc_crit0: trip1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&soc_alert0>; |
| cooling-device = |
| <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| clock-frequency = <8000000>; |
| arm,no-tick-in-suspend; |
| }; |
| |
| soc: soc@0 { |
| compatible = "fsl,imx8mp-soc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x0 0x3e000000>; |
| nvmem-cells = <&imx8mp_uid>; |
| nvmem-cell-names = "soc_unique_id"; |
| |
| etm0: etm@28440000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28440000 0x1000>; |
| cpu = <&A53_0>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm0_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm1: etm@28540000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28540000 0x1000>; |
| cpu = <&A53_1>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm1_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port1>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm2: etm@28640000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28640000 0x1000>; |
| cpu = <&A53_2>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm2_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port2>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm3: etm@28740000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28740000 0x1000>; |
| cpu = <&A53_3>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm3_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port3>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@28c03000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x28c03000 0x1000>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| hugo_funnel_in_port0: endpoint { |
| remote-endpoint = <&ca_funnel_out_port0>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| hugo_funnel_in_port1: endpoint { |
| /* M7 input */ |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| hugo_funnel_in_port2: endpoint { |
| /* DSP input */ |
| }; |
| }; |
| /* the other input ports are not connect to anything */ |
| }; |
| |
| out-ports { |
| port { |
| hugo_funnel_out_port0: endpoint { |
| remote-endpoint = <&etf_in_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| etf@28c04000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x28c04000 0x1000>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| etf_in_port: endpoint { |
| remote-endpoint = <&hugo_funnel_out_port0>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| etf_out_port: endpoint { |
| remote-endpoint = <&etr_in_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| etr@28c06000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x28c06000 0x1000>; |
| clocks = <&clk IMX8MP_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| etr_in_port: endpoint { |
| remote-endpoint = <&etf_out_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| aips1: bus@30000000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30000000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio1: gpio@30200000 { |
| compatible = "fsl,imx8mp-gpio", "fsl,imx35-gpio"; |
| reg = <0x30200000 0x10000>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPIO1_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 5 30>; |
| }; |
| |
| gpio2: gpio@30210000 { |
| compatible = "fsl,imx8mp-gpio", "fsl,imx35-gpio"; |
| reg = <0x30210000 0x10000>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPIO2_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 35 21>; |
| }; |
| |
| gpio3: gpio@30220000 { |
| compatible = "fsl,imx8mp-gpio", "fsl,imx35-gpio"; |
| reg = <0x30220000 0x10000>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPIO3_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>; |
| }; |
| |
| gpio4: gpio@30230000 { |
| compatible = "fsl,imx8mp-gpio", "fsl,imx35-gpio"; |
| reg = <0x30230000 0x10000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPIO4_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 82 32>; |
| }; |
| |
| gpio5: gpio@30240000 { |
| compatible = "fsl,imx8mp-gpio", "fsl,imx35-gpio"; |
| reg = <0x30240000 0x10000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPIO5_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 114 30>; |
| }; |
| |
| tmu: tmu@30260000 { |
| compatible = "fsl,imx8mp-tmu"; |
| reg = <0x30260000 0x10000>; |
| clocks = <&clk IMX8MP_CLK_TSENSOR_ROOT>; |
| nvmem-cells = <&tmu_calib>; |
| nvmem-cell-names = "calib"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| wdog1: watchdog@30280000 { |
| compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt"; |
| reg = <0x30280000 0x10000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_WDOG1_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog2: watchdog@30290000 { |
| compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt"; |
| reg = <0x30290000 0x10000>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_WDOG2_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog3: watchdog@302a0000 { |
| compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt"; |
| reg = <0x302a0000 0x10000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_WDOG3_ROOT>; |
| status = "disabled"; |
| }; |
| |
| gpt1: timer@302d0000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x302d0000 0x10000>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT1_ROOT>, <&clk IMX8MP_CLK_GPT1>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt2: timer@302e0000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x302e0000 0x10000>; |
| interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT2_ROOT>, <&clk IMX8MP_CLK_GPT2>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt3: timer@302f0000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x302f0000 0x10000>; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT3_ROOT>, <&clk IMX8MP_CLK_GPT3>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| iomuxc: pinctrl@30330000 { |
| compatible = "fsl,imx8mp-iomuxc"; |
| reg = <0x30330000 0x10000>; |
| }; |
| |
| gpr: syscon@30340000 { |
| compatible = "fsl,imx8mp-iomuxc-gpr", "syscon"; |
| reg = <0x30340000 0x10000>; |
| }; |
| |
| ocotp: efuse@30350000 { |
| compatible = "fsl,imx8mp-ocotp", "fsl,imx8mm-ocotp", "syscon"; |
| reg = <0x30350000 0x10000>; |
| clocks = <&clk IMX8MP_CLK_OCOTP_ROOT>; |
| /* For nvmem subnodes */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* |
| * The register address below maps to the MX8M |
| * Fusemap Description Table entries this way. |
| * Assuming |
| * reg = <ADDR SIZE>; |
| * then |
| * Fuse Address = (ADDR * 4) + 0x400 |
| * Note that if SIZE is greater than 4, then |
| * each subsequent fuse is located at offset |
| * +0x10 in Fusemap Description Table (e.g. |
| * reg = <0x8 0x8> describes fuses 0x420 and |
| * 0x430). |
| */ |
| imx8mp_uid: unique-id@8 { /* 0x420-0x430 */ |
| reg = <0x8 0x8>; |
| }; |
| |
| cpu_speed_grade: speed-grade@10 { /* 0x440 */ |
| reg = <0x10 4>; |
| }; |
| |
| eth_mac1: mac-address@90 { /* 0x640 */ |
| reg = <0x90 6>; |
| }; |
| |
| eth_mac2: mac-address@96 { /* 0x658 */ |
| reg = <0x96 6>; |
| }; |
| |
| tmu_calib: calib@264 { /* 0xd90-0xdc0 */ |
| reg = <0x264 0x10>; |
| }; |
| }; |
| |
| anatop: clock-controller@30360000 { |
| compatible = "fsl,imx8mp-anatop", "fsl,imx8mm-anatop"; |
| reg = <0x30360000 0x10000>; |
| #clock-cells = <1>; |
| }; |
| |
| snvs: snvs@30370000 { |
| compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd"; |
| reg = <0x30370000 0x10000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_SNVS_ROOT>; |
| clock-names = "snvs-rtc"; |
| }; |
| |
| snvs_pwrkey: snvs-powerkey { |
| compatible = "fsl,sec-v4.0-pwrkey"; |
| regmap = <&snvs>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_SNVS_ROOT>; |
| clock-names = "snvs-pwrkey"; |
| linux,keycode = <KEY_POWER>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| |
| snvs_lpgpr: snvs-lpgpr { |
| compatible = "fsl,imx8mp-snvs-lpgpr", |
| "fsl,imx7d-snvs-lpgpr"; |
| }; |
| }; |
| |
| clk: clock-controller@30380000 { |
| compatible = "fsl,imx8mp-ccm"; |
| reg = <0x30380000 0x10000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>, |
| <&clk_ext3>, <&clk_ext4>; |
| clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2", |
| "clk_ext3", "clk_ext4"; |
| assigned-clocks = <&clk IMX8MP_CLK_A53_SRC>, |
| <&clk IMX8MP_CLK_A53_CORE>, |
| <&clk IMX8MP_CLK_NOC>, |
| <&clk IMX8MP_CLK_NOC_IO>, |
| <&clk IMX8MP_CLK_GIC>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_ARM_PLL_OUT>, |
| <&clk IMX8MP_SYS_PLL2_1000M>, |
| <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL2_500M>; |
| assigned-clock-rates = <0>, <0>, |
| <1000000000>, |
| <800000000>, |
| <500000000>; |
| }; |
| |
| src: reset-controller@30390000 { |
| compatible = "fsl,imx8mp-src", "syscon"; |
| reg = <0x30390000 0x10000>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| |
| gpc: gpc@303a0000 { |
| compatible = "fsl,imx8mp-gpc"; |
| reg = <0x303a0000 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| |
| pgc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pgc_mipi_phy1: power-domain@0 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY1>; |
| }; |
| |
| pgc_pcie_phy: power-domain@1 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_PCIE_PHY>; |
| }; |
| |
| pgc_usb1_phy: power-domain@2 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_USB1_PHY>; |
| }; |
| |
| pgc_usb2_phy: power-domain@3 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_USB2_PHY>; |
| }; |
| |
| pgc_audio: power-domain@5 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_AUDIOMIX>; |
| clocks = <&clk IMX8MP_CLK_AUDIO_ROOT>, |
| <&clk IMX8MP_CLK_AUDIO_AXI>; |
| assigned-clocks = <&clk IMX8MP_CLK_AUDIO_AHB>, |
| <&clk IMX8MP_CLK_AUDIO_AXI_SRC>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL1_800M>; |
| assigned-clock-rates = <400000000>, |
| <600000000>; |
| }; |
| |
| pgc_gpu2d: power-domain@6 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_GPU2D>; |
| clocks = <&clk IMX8MP_CLK_GPU2D_ROOT>; |
| power-domains = <&pgc_gpumix>; |
| }; |
| |
| pgc_gpumix: power-domain@7 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_GPUMIX>; |
| clocks = <&clk IMX8MP_CLK_GPU_ROOT>, |
| <&clk IMX8MP_CLK_GPU_AHB>; |
| assigned-clocks = <&clk IMX8MP_CLK_GPU_AXI>, |
| <&clk IMX8MP_CLK_GPU_AHB>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL1_800M>; |
| assigned-clock-rates = <800000000>, <400000000>; |
| }; |
| |
| pgc_gpu3d: power-domain@9 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_GPU3D>; |
| clocks = <&clk IMX8MP_CLK_GPU3D_ROOT>, |
| <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>; |
| power-domains = <&pgc_gpumix>; |
| }; |
| |
| pgc_mediamix: power-domain@10 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; |
| }; |
| |
| pgc_hdmimix: power-domain@14 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_HDMIMIX>; |
| clocks = <&clk IMX8MP_CLK_HDMI_ROOT>, |
| <&clk IMX8MP_CLK_HDMI_APB>; |
| assigned-clocks = <&clk IMX8MP_CLK_HDMI_AXI>, |
| <&clk IMX8MP_CLK_HDMI_APB>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>, |
| <&clk IMX8MP_SYS_PLL1_133M>; |
| assigned-clock-rates = <500000000>, <133000000>; |
| }; |
| |
| pgc_hdmi_phy: power-domain@15 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_HDMI_PHY>; |
| }; |
| |
| pgc_mipi_phy2: power-domain@16 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>; |
| }; |
| |
| pgc_hsiomix: power-domain@17 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>; |
| clocks = <&clk IMX8MP_CLK_HSIO_AXI>, |
| <&clk IMX8MP_CLK_HSIO_ROOT>; |
| assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>; |
| assigned-clock-rates = <500000000>; |
| }; |
| |
| pgc_ispdwp: power-domain@18 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>; |
| }; |
| |
| pgc_vpumix: power-domain@19 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_VPUMIX>; |
| clocks = <&clk IMX8MP_CLK_VPU_ROOT>; |
| }; |
| |
| pgc_vpu_g1: power-domain@20 { |
| #power-domain-cells = <0>; |
| power-domains = <&pgc_vpumix>; |
| reg = <IMX8MP_POWER_DOMAIN_VPU_G1>; |
| clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>; |
| }; |
| |
| pgc_vpu_g2: power-domain@21 { |
| #power-domain-cells = <0>; |
| power-domains = <&pgc_vpumix>; |
| reg = <IMX8MP_POWER_DOMAIN_VPU_G2>; |
| clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>; |
| }; |
| |
| pgc_vpu_vc8000e: power-domain@22 { |
| #power-domain-cells = <0>; |
| power-domains = <&pgc_vpumix>; |
| reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>; |
| clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>; |
| }; |
| |
| pgc_mlmix: power-domain@24 { |
| #power-domain-cells = <0>; |
| reg = <IMX8MP_POWER_DOMAIN_MLMIX>; |
| clocks = <&clk IMX8MP_CLK_ML_AXI>, |
| <&clk IMX8MP_CLK_ML_AHB>, |
| <&clk IMX8MP_CLK_NPU_ROOT>; |
| assigned-clocks = <&clk IMX8MP_CLK_ML_CORE>, |
| <&clk IMX8MP_CLK_ML_AXI>, |
| <&clk IMX8MP_CLK_ML_AHB>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL1_800M>; |
| assigned-clock-rates = <800000000>, |
| <800000000>, |
| <300000000>; |
| }; |
| }; |
| }; |
| }; |
| |
| aips2: bus@30400000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30400000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pwm1: pwm@30660000 { |
| compatible = "fsl,imx8mp-pwm", "fsl,imx27-pwm"; |
| reg = <0x30660000 0x10000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_PWM1_ROOT>, |
| <&clk IMX8MP_CLK_PWM1_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@30670000 { |
| compatible = "fsl,imx8mp-pwm", "fsl,imx27-pwm"; |
| reg = <0x30670000 0x10000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_PWM2_ROOT>, |
| <&clk IMX8MP_CLK_PWM2_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@30680000 { |
| compatible = "fsl,imx8mp-pwm", "fsl,imx27-pwm"; |
| reg = <0x30680000 0x10000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_PWM3_ROOT>, |
| <&clk IMX8MP_CLK_PWM3_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm4: pwm@30690000 { |
| compatible = "fsl,imx8mp-pwm", "fsl,imx27-pwm"; |
| reg = <0x30690000 0x10000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_PWM4_ROOT>, |
| <&clk IMX8MP_CLK_PWM4_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| system_counter: timer@306a0000 { |
| compatible = "nxp,sysctr-timer"; |
| reg = <0x306a0000 0x20000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&osc_24m>; |
| clock-names = "per"; |
| }; |
| |
| gpt6: timer@306e0000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x306e0000 0x10000>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT6_ROOT>, <&clk IMX8MP_CLK_GPT6>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt5: timer@306f0000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x306f0000 0x10000>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT5_ROOT>, <&clk IMX8MP_CLK_GPT5>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt4: timer@30700000 { |
| compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x30700000 0x10000>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPT4_ROOT>, <&clk IMX8MP_CLK_GPT4>; |
| clock-names = "ipg", "per"; |
| }; |
| }; |
| |
| aips3: bus@30800000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30800000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| spba-bus@30800000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| reg = <0x30800000 0x100000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| ecspi1: spi@30820000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; |
| reg = <0x30820000 0x10000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>, |
| <&clk IMX8MP_CLK_ECSPI1_ROOT>; |
| clock-names = "ipg", "per"; |
| assigned-clock-rates = <80000000>; |
| assigned-clocks = <&clk IMX8MP_CLK_ECSPI1>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; |
| dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: spi@30830000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; |
| reg = <0x30830000 0x10000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>, |
| <&clk IMX8MP_CLK_ECSPI2_ROOT>; |
| clock-names = "ipg", "per"; |
| assigned-clock-rates = <80000000>; |
| assigned-clocks = <&clk IMX8MP_CLK_ECSPI2>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; |
| dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: spi@30840000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; |
| reg = <0x30840000 0x10000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>, |
| <&clk IMX8MP_CLK_ECSPI3_ROOT>; |
| clock-names = "ipg", "per"; |
| assigned-clock-rates = <80000000>; |
| assigned-clocks = <&clk IMX8MP_CLK_ECSPI3>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; |
| dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@30860000 { |
| compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; |
| reg = <0x30860000 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_UART1_ROOT>, |
| <&clk IMX8MP_CLK_UART1_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@30880000 { |
| compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; |
| reg = <0x30880000 0x10000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_UART3_ROOT>, |
| <&clk IMX8MP_CLK_UART3_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@30890000 { |
| compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; |
| reg = <0x30890000 0x10000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_UART2_ROOT>, |
| <&clk IMX8MP_CLK_UART2_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| flexcan1: can@308c0000 { |
| compatible = "fsl,imx8mp-flexcan"; |
| reg = <0x308c0000 0x10000>; |
| interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_IPG_ROOT>, |
| <&clk IMX8MP_CLK_CAN1_ROOT>; |
| clock-names = "ipg", "per"; |
| assigned-clocks = <&clk IMX8MP_CLK_CAN1>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; |
| assigned-clock-rates = <40000000>; |
| fsl,clk-source = /bits/ 8 <0>; |
| fsl,stop-mode = <&gpr 0x10 4>; |
| status = "disabled"; |
| }; |
| |
| flexcan2: can@308d0000 { |
| compatible = "fsl,imx8mp-flexcan"; |
| reg = <0x308d0000 0x10000>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_IPG_ROOT>, |
| <&clk IMX8MP_CLK_CAN2_ROOT>; |
| clock-names = "ipg", "per"; |
| assigned-clocks = <&clk IMX8MP_CLK_CAN2>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; |
| assigned-clock-rates = <40000000>; |
| fsl,clk-source = /bits/ 8 <0>; |
| fsl,stop-mode = <&gpr 0x10 5>; |
| status = "disabled"; |
| }; |
| }; |
| |
| crypto: crypto@30900000 { |
| compatible = "fsl,sec-v4.0"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x30900000 0x40000>; |
| ranges = <0 0x30900000 0x40000>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_AHB>, |
| <&clk IMX8MP_CLK_IPG_ROOT>; |
| clock-names = "aclk", "ipg"; |
| |
| sec_jr0: jr@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sec_jr1: jr@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr2: jr@3000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x3000 0x1000>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| i2c1: i2c@30a20000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a20000 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C1_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@30a30000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a30000 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C2_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@30a40000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a40000 0x10000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C3_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@30a50000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a50000 0x10000>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C4_ROOT>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@30a60000 { |
| compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; |
| reg = <0x30a60000 0x10000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_UART4_ROOT>, |
| <&clk IMX8MP_CLK_UART4_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| mu: mailbox@30aa0000 { |
| compatible = "fsl,imx8mp-mu", "fsl,imx6sx-mu"; |
| reg = <0x30aa0000 0x10000>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_MU_ROOT>; |
| #mbox-cells = <2>; |
| }; |
| |
| mu2: mailbox@30e60000 { |
| compatible = "fsl,imx8mp-mu", "fsl,imx6sx-mu"; |
| reg = <0x30e60000 0x10000>; |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| #mbox-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@30ad0000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30ad0000 0x10000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C5_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@30ae0000 { |
| compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30ae0000 0x10000>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_I2C6_ROOT>; |
| status = "disabled"; |
| }; |
| |
| usdhc1: mmc@30b40000 { |
| compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b40000 0x10000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_DUMMY>, |
| <&clk IMX8MP_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MP_CLK_USDHC1_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: mmc@30b50000 { |
| compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b50000 0x10000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_DUMMY>, |
| <&clk IMX8MP_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MP_CLK_USDHC2_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc3: mmc@30b60000 { |
| compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b60000 0x10000>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_DUMMY>, |
| <&clk IMX8MP_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MP_CLK_USDHC3_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| flexspi: spi@30bb0000 { |
| compatible = "nxp,imx8mp-fspi"; |
| reg = <0x30bb0000 0x10000>, <0x8000000 0x10000000>; |
| reg-names = "fspi_base", "fspi_mmap"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_QSPI_ROOT>, |
| <&clk IMX8MP_CLK_QSPI_ROOT>; |
| clock-names = "fspi_en", "fspi"; |
| assigned-clock-rates = <80000000>; |
| assigned-clocks = <&clk IMX8MP_CLK_QSPI>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| sdma1: dma-controller@30bd0000 { |
| compatible = "fsl,imx8mp-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x30bd0000 0x10000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_SDMA1_ROOT>, |
| <&clk IMX8MP_CLK_AHB>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| fec: ethernet@30be0000 { |
| compatible = "fsl,imx8mp-fec", "fsl,imx8mq-fec", "fsl,imx6sx-fec"; |
| reg = <0x30be0000 0x10000>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_ENET1_ROOT>, |
| <&clk IMX8MP_CLK_SIM_ENET_ROOT>, |
| <&clk IMX8MP_CLK_ENET_TIMER>, |
| <&clk IMX8MP_CLK_ENET_REF>, |
| <&clk IMX8MP_CLK_ENET_PHY_REF>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, |
| <&clk IMX8MP_CLK_ENET_TIMER>, |
| <&clk IMX8MP_CLK_ENET_REF>, |
| <&clk IMX8MP_CLK_ENET_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, |
| <&clk IMX8MP_SYS_PLL2_100M>, |
| <&clk IMX8MP_SYS_PLL2_125M>, |
| <&clk IMX8MP_SYS_PLL2_50M>; |
| assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; |
| fsl,num-tx-queues = <3>; |
| fsl,num-rx-queues = <3>; |
| nvmem-cells = <ð_mac1>; |
| nvmem-cell-names = "mac-address"; |
| fsl,stop-mode = <&gpr 0x10 3>; |
| status = "disabled"; |
| }; |
| |
| eqos: ethernet@30bf0000 { |
| compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; |
| reg = <0x30bf0000 0x10000>; |
| interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq", "eth_wake_irq"; |
| clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, |
| <&clk IMX8MP_CLK_QOS_ENET_ROOT>, |
| <&clk IMX8MP_CLK_ENET_QOS_TIMER>, |
| <&clk IMX8MP_CLK_ENET_QOS>; |
| clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; |
| assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, |
| <&clk IMX8MP_CLK_ENET_QOS_TIMER>, |
| <&clk IMX8MP_CLK_ENET_QOS>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, |
| <&clk IMX8MP_SYS_PLL2_100M>, |
| <&clk IMX8MP_SYS_PLL2_125M>; |
| assigned-clock-rates = <0>, <100000000>, <125000000>; |
| nvmem-cells = <ð_mac2>; |
| nvmem-cell-names = "mac-address"; |
| intf_mode = <&gpr 0x4>; |
| status = "disabled"; |
| }; |
| }; |
| |
| aips5: bus@30c00000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30c00000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| spba-bus@30c00000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| reg = <0x30c00000 0x100000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| sai1: sai@30c10000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c10000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI1_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI1_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI1_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI1_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sai2: sai@30c20000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c20000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sai3: sai@30c30000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c30000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sai5: sai@30c50000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c50000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI5_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI5_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI5_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI5_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sai6: sai@30c60000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c60000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI6_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI6_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI6_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI6_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sai7: sai@30c80000 { |
| compatible = "fsl,imx8mp-sai", "fsl,imx8mq-sai"; |
| reg = <0x30c80000 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI7_IPG>, |
| <&clk IMX8MP_CLK_DUMMY>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI7_MCLK1>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI7_MCLK2>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI7_MCLK3>; |
| clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 12 2 0>, <&sdma2 13 2 0>; |
| dma-names = "rx", "tx"; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| easrc: easrc@30c90000 { |
| compatible = "fsl,imx8mp-easrc", "fsl,imx8mn-easrc"; |
| reg = <0x30c90000 0x10000>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_ASRC_IPG>; |
| clock-names = "mem"; |
| dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>, |
| <&sdma2 18 23 0> , <&sdma2 19 23 0>, |
| <&sdma2 20 23 0> , <&sdma2 21 23 0>, |
| <&sdma2 22 23 0> , <&sdma2 23 23 0>; |
| dma-names = "ctx0_rx", "ctx0_tx", |
| "ctx1_rx", "ctx1_tx", |
| "ctx2_rx", "ctx2_tx", |
| "ctx3_rx", "ctx3_tx"; |
| firmware-name = "imx/easrc/easrc-imx8mn.bin"; |
| fsl,asrc-rate = <8000>; |
| fsl,asrc-format = <2>; |
| status = "disabled"; |
| }; |
| |
| micfil: audio-controller@30ca0000 { |
| compatible = "fsl,imx8mp-micfil"; |
| reg = <0x30ca0000 0x10000>; |
| #sound-dai-cells = <0>; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_PDM_IPG>, |
| <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_PDM_SEL>, |
| <&clk IMX8MP_AUDIO_PLL1_OUT>, |
| <&clk IMX8MP_AUDIO_PLL2_OUT>, |
| <&clk IMX8MP_CLK_EXT3>; |
| clock-names = "ipg_clk", "ipg_clk_app", |
| "pll8k", "pll11k", "clkext3"; |
| dmas = <&sdma2 24 25 0x80000000>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| aud2htx: aud2htx@30cb0000 { |
| compatible = "fsl,imx8mp-aud2htx"; |
| reg = <0x30cb0000 0x10000>; |
| interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_AUD2HTX_IPG>; |
| clock-names = "bus"; |
| dmas = <&sdma2 26 2 0>; |
| dma-names = "tx"; |
| status = "disabled"; |
| }; |
| }; |
| |
| sdma3: dma-controller@30e00000 { |
| compatible = "fsl,imx8mp-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x30e00000 0x10000>; |
| #dma-cells = <3>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SDMA3_ROOT>, |
| <&clk IMX8MP_CLK_AUDIO_ROOT>; |
| clock-names = "ipg", "ahb"; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| sdma2: dma-controller@30e10000 { |
| compatible = "fsl,imx8mp-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x30e10000 0x10000>; |
| #dma-cells = <3>; |
| clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SDMA2_ROOT>, |
| <&clk IMX8MP_CLK_AUDIO_ROOT>; |
| clock-names = "ipg", "ahb"; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| audio_blk_ctrl: clock-controller@30e20000 { |
| compatible = "fsl,imx8mp-audio-blk-ctrl"; |
| reg = <0x30e20000 0x10000>; |
| #clock-cells = <1>; |
| clocks = <&clk IMX8MP_CLK_AUDIO_ROOT>, |
| <&clk IMX8MP_CLK_SAI1>, |
| <&clk IMX8MP_CLK_SAI2>, |
| <&clk IMX8MP_CLK_SAI3>, |
| <&clk IMX8MP_CLK_SAI5>, |
| <&clk IMX8MP_CLK_SAI6>, |
| <&clk IMX8MP_CLK_SAI7>; |
| clock-names = "ahb", |
| "sai1", "sai2", "sai3", |
| "sai5", "sai6", "sai7"; |
| power-domains = <&pgc_audio>; |
| }; |
| }; |
| |
| noc: interconnect@32700000 { |
| compatible = "fsl,imx8mp-noc", "fsl,imx8m-noc"; |
| reg = <0x32700000 0x100000>; |
| clocks = <&clk IMX8MP_CLK_NOC>; |
| #interconnect-cells = <1>; |
| operating-points-v2 = <&noc_opp_table>; |
| |
| noc_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| }; |
| |
| opp-1000000000 { |
| opp-hz = /bits/ 64 <1000000000>; |
| }; |
| }; |
| }; |
| |
| aips4: bus@32c00000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x32c00000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| isi_0: isi@32e00000 { |
| compatible = "fsl,imx8mp-isi"; |
| reg = <0x32e00000 0x4000>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; |
| clock-names = "axi", "apb"; |
| fsl,blk-ctrl = <&media_blk_ctrl>; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_ISI>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| isi_in_0: endpoint { |
| remote-endpoint = <&mipi_csi_0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| isi_in_1: endpoint { |
| remote-endpoint = <&mipi_csi_1_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| dewarp: dwe@32e30000 { |
| compatible = "nxp,imx8mp-dw100"; |
| reg = <0x32e30000 0x10000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; |
| clock-names = "axi", "ahb"; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_DWE>; |
| }; |
| |
| mipi_csi_0: csi@32e40000 { |
| compatible = "fsl,imx8mp-mipi-csi2", "fsl,imx8mm-mipi-csi2"; |
| reg = <0x32e40000 0x10000>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <266000000>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_CAM1_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>; |
| clock-names = "pclk", "wrap", "phy", "axi"; |
| assigned-clocks = <&clk IMX8MP_CLK_MEDIA_CAM1_PIX>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>, |
| <&clk IMX8MP_CLK_24M>; |
| assigned-clock-rates = <266000000>; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_MIPI_CSI2_1>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mipi_csi_0_out: endpoint { |
| remote-endpoint = <&isi_in_0>; |
| }; |
| }; |
| }; |
| }; |
| |
| mipi_csi_1: csi@32e50000 { |
| compatible = "fsl,imx8mp-mipi-csi2", "fsl,imx8mm-mipi-csi2"; |
| reg = <0x32e50000 0x10000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <266000000>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_CAM2_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>; |
| clock-names = "pclk", "wrap", "phy", "axi"; |
| assigned-clocks = <&clk IMX8MP_CLK_MEDIA_CAM1_PIX>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>, |
| <&clk IMX8MP_CLK_24M>; |
| assigned-clock-rates = <266000000>; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_MIPI_CSI2_2>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mipi_csi_1_out: endpoint { |
| remote-endpoint = <&isi_in_1>; |
| }; |
| }; |
| }; |
| }; |
| |
| mipi_dsi: dsi@32e60000 { |
| compatible = "fsl,imx8mp-mipi-dsim"; |
| reg = <0x32e60000 0x400>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>; |
| clock-names = "bus_clk", "sclk_mipi"; |
| assigned-clocks = <&clk IMX8MP_CLK_MEDIA_APB>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_CLK_24M>; |
| assigned-clock-rates = <200000000>, <24000000>; |
| samsung,pll-clock-frequency = <24000000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_MIPI_DSI_1>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| dsim_from_lcdif1: endpoint { |
| remote-endpoint = <&lcdif1_to_dsim>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mipi_dsi_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| lcdif1: display-controller@32e80000 { |
| compatible = "fsl,imx8mp-lcdif"; |
| reg = <0x32e80000 0x10000>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_DISP1_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>; |
| clock-names = "pix", "axi", "disp_axi"; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_1>; |
| status = "disabled"; |
| |
| port { |
| lcdif1_to_dsim: endpoint { |
| remote-endpoint = <&dsim_from_lcdif1>; |
| }; |
| }; |
| }; |
| |
| lcdif2: display-controller@32e90000 { |
| compatible = "fsl,imx8mp-lcdif"; |
| reg = <0x32e90000 0x10000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>; |
| clock-names = "pix", "axi", "disp_axi"; |
| power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_2>; |
| status = "disabled"; |
| |
| port { |
| lcdif2_to_ldb: endpoint { |
| remote-endpoint = <&ldb_from_lcdif2>; |
| }; |
| }; |
| }; |
| |
| media_blk_ctrl: blk-ctrl@32ec0000 { |
| compatible = "fsl,imx8mp-media-blk-ctrl", |
| "syscon"; |
| reg = <0x32ec0000 0x10000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| power-domains = <&pgc_mediamix>, |
| <&pgc_mipi_phy1>, |
| <&pgc_mipi_phy1>, |
| <&pgc_mediamix>, |
| <&pgc_mediamix>, |
| <&pgc_mipi_phy2>, |
| <&pgc_mediamix>, |
| <&pgc_ispdwp>, |
| <&pgc_ispdwp>, |
| <&pgc_mipi_phy2>; |
| power-domain-names = "bus", "mipi-dsi1", "mipi-csi1", |
| "lcdif1", "isi", "mipi-csi2", |
| "lcdif2", "isp", "dwe", |
| "mipi-dsi2"; |
| interconnects = |
| <&noc IMX8MP_ICM_LCDIF_RD &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_LCDIF_WR &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_ISI0 &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_ISI1 &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_ISI2 &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_ISP0 &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_ISP1 &noc IMX8MP_ICN_MEDIA>, |
| <&noc IMX8MP_ICM_DWE &noc IMX8MP_ICN_MEDIA>; |
| interconnect-names = "lcdif-rd", "lcdif-wr", "isi0", |
| "isi1", "isi2", "isp0", "isp1", |
| "dwe"; |
| clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_CAM1_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_CAM2_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_DISP1_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>, |
| <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF_ROOT>; |
| clock-names = "apb", "axi", "cam1", "cam2", |
| "disp1", "disp2", "isp", "phy"; |
| |
| assigned-clocks = <&clk IMX8MP_CLK_MEDIA_AXI>, |
| <&clk IMX8MP_CLK_MEDIA_APB>, |
| <&clk IMX8MP_CLK_MEDIA_DISP1_PIX>, |
| <&clk IMX8MP_CLK_MEDIA_DISP2_PIX>, |
| <&clk IMX8MP_VIDEO_PLL1>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>, |
| <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_VIDEO_PLL1_OUT>, |
| <&clk IMX8MP_VIDEO_PLL1_OUT>; |
| assigned-clock-rates = <500000000>, <200000000>, |
| <0>, <0>, <1039500000>; |
| #power-domain-cells = <1>; |
| |
| lvds_bridge: bridge@5c { |
| compatible = "fsl,imx8mp-ldb"; |
| reg = <0x5c 0x4>, <0x128 0x4>; |
| reg-names = "ldb", "lvds"; |
| clocks = <&clk IMX8MP_CLK_MEDIA_LDB_ROOT>; |
| clock-names = "ldb"; |
| assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>; |
| assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| ldb_from_lcdif2: endpoint { |
| remote-endpoint = <&lcdif2_to_ldb>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| ldb_lvds_ch0: endpoint { |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| ldb_lvds_ch1: endpoint { |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| pcie_phy: pcie-phy@32f00000 { |
| compatible = "fsl,imx8mp-pcie-phy"; |
| reg = <0x32f00000 0x10000>; |
| resets = <&src IMX8MP_RESET_PCIEPHY>, |
| <&src IMX8MP_RESET_PCIEPHY_PERST>; |
| reset-names = "pciephy", "perst"; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE_PHY>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| hsio_blk_ctrl: blk-ctrl@32f10000 { |
| compatible = "fsl,imx8mp-hsio-blk-ctrl", "syscon"; |
| reg = <0x32f10000 0x24>; |
| clocks = <&clk IMX8MP_CLK_USB_ROOT>, |
| <&clk IMX8MP_CLK_PCIE_ROOT>; |
| clock-names = "usb", "pcie"; |
| power-domains = <&pgc_hsiomix>, <&pgc_hsiomix>, |
| <&pgc_usb1_phy>, <&pgc_usb2_phy>, |
| <&pgc_hsiomix>, <&pgc_pcie_phy>; |
| power-domain-names = "bus", "usb", "usb-phy1", |
| "usb-phy2", "pcie", "pcie-phy"; |
| interconnects = <&noc IMX8MP_ICM_NOC_PCIE &noc IMX8MP_ICN_HSIO>, |
| <&noc IMX8MP_ICM_USB1 &noc IMX8MP_ICN_HSIO>, |
| <&noc IMX8MP_ICM_USB2 &noc IMX8MP_ICN_HSIO>, |
| <&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>; |
| interconnect-names = "noc-pcie", "usb1", "usb2", "pcie"; |
| #power-domain-cells = <1>; |
| #clock-cells = <0>; |
| }; |
| |
| hdmi_blk_ctrl: blk-ctrl@32fc0000 { |
| compatible = "fsl,imx8mp-hdmi-blk-ctrl", "syscon"; |
| reg = <0x32fc0000 0x1000>; |
| clocks = <&clk IMX8MP_CLK_HDMI_APB>, |
| <&clk IMX8MP_CLK_HDMI_ROOT>, |
| <&clk IMX8MP_CLK_HDMI_REF_266M>, |
| <&clk IMX8MP_CLK_HDMI_24M>, |
| <&clk IMX8MP_CLK_HDMI_FDCC_TST>; |
| clock-names = "apb", "axi", "ref_266m", "ref_24m", "fdcc"; |
| power-domains = <&pgc_hdmimix>, <&pgc_hdmimix>, |
| <&pgc_hdmimix>, <&pgc_hdmimix>, |
| <&pgc_hdmimix>, <&pgc_hdmimix>, |
| <&pgc_hdmimix>, <&pgc_hdmi_phy>, |
| <&pgc_hdmimix>, <&pgc_hdmimix>; |
| power-domain-names = "bus", "irqsteer", "lcdif", |
| "pai", "pvi", "trng", |
| "hdmi-tx", "hdmi-tx-phy", |
| "hdcp", "hrv"; |
| #power-domain-cells = <1>; |
| }; |
| |
| irqsteer_hdmi: interrupt-controller@32fc2000 { |
| compatible = "fsl,imx-irqsteer"; |
| reg = <0x32fc2000 0x1000>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| fsl,channel = <1>; |
| fsl,num-irqs = <64>; |
| clocks = <&clk IMX8MP_CLK_HDMI_APB>; |
| clock-names = "ipg"; |
| power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_IRQSTEER>; |
| }; |
| |
| hdmi_pvi: display-bridge@32fc4000 { |
| compatible = "fsl,imx8mp-hdmi-pvi"; |
| reg = <0x32fc4000 0x1000>; |
| interrupt-parent = <&irqsteer_hdmi>; |
| interrupts = <12>; |
| power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_PVI>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| pvi_from_lcdif3: endpoint { |
| remote-endpoint = <&lcdif3_to_pvi>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| pvi_to_hdmi_tx: endpoint { |
| remote-endpoint = <&hdmi_tx_from_pvi>; |
| }; |
| }; |
| }; |
| }; |
| |
| lcdif3: display-controller@32fc6000 { |
| compatible = "fsl,imx8mp-lcdif"; |
| reg = <0x32fc6000 0x1000>; |
| interrupt-parent = <&irqsteer_hdmi>; |
| interrupts = <8>; |
| clocks = <&hdmi_tx_phy>, |
| <&clk IMX8MP_CLK_HDMI_APB>, |
| <&clk IMX8MP_CLK_HDMI_ROOT>; |
| clock-names = "pix", "axi", "disp_axi"; |
| power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_LCDIF>; |
| status = "disabled"; |
| |
| port { |
| lcdif3_to_pvi: endpoint { |
| remote-endpoint = <&pvi_from_lcdif3>; |
| }; |
| }; |
| }; |
| |
| hdmi_tx: hdmi@32fd8000 { |
| compatible = "fsl,imx8mp-hdmi-tx"; |
| reg = <0x32fd8000 0x7eff>; |
| interrupt-parent = <&irqsteer_hdmi>; |
| interrupts = <0>; |
| clocks = <&clk IMX8MP_CLK_HDMI_APB>, |
| <&clk IMX8MP_CLK_HDMI_REF_266M>, |
| <&clk IMX8MP_CLK_32K>, |
| <&hdmi_tx_phy>; |
| clock-names = "iahb", "isfr", "cec", "pix"; |
| assigned-clocks = <&clk IMX8MP_CLK_HDMI_REF_266M>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>; |
| power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_HDMI_TX>; |
| reg-io-width = <1>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| hdmi_tx_from_pvi: endpoint { |
| remote-endpoint = <&pvi_to_hdmi_tx>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| /* Point endpoint to the HDMI connector */ |
| }; |
| }; |
| }; |
| |
| hdmi_tx_phy: phy@32fdff00 { |
| compatible = "fsl,imx8mp-hdmi-phy"; |
| reg = <0x32fdff00 0x100>; |
| clocks = <&clk IMX8MP_CLK_HDMI_APB>, |
| <&clk IMX8MP_CLK_HDMI_24M>; |
| clock-names = "apb", "ref"; |
| assigned-clocks = <&clk IMX8MP_CLK_HDMI_24M>; |
| assigned-clock-parents = <&clk IMX8MP_CLK_24M>; |
| power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_HDMI_TX_PHY>; |
| #clock-cells = <0>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pcie: pcie@33800000 { |
| compatible = "fsl,imx8mp-pcie"; |
| reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>; |
| reg-names = "dbi", "config"; |
| clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, |
| <&clk IMX8MP_CLK_HSIO_AXI>, |
| <&clk IMX8MP_CLK_PCIE_ROOT>; |
| clock-names = "pcie", "pcie_bus", "pcie_aux"; |
| assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; |
| assigned-clock-rates = <10000000>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */ |
| <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */ |
| num-lanes = <1>; |
| num-viewport = <4>; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,max-link-speed = <3>; |
| linux,pci-domain = <0>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>; |
| resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>, |
| <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>; |
| reset-names = "apps", "turnoff"; |
| phys = <&pcie_phy>; |
| phy-names = "pcie-phy"; |
| status = "disabled"; |
| }; |
| |
| pcie_ep: pcie-ep@33800000 { |
| compatible = "fsl,imx8mp-pcie-ep"; |
| reg = <0x33800000 0x000400000>, <0x18000000 0x08000000>; |
| reg-names = "dbi", "addr_space"; |
| clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, |
| <&clk IMX8MP_CLK_HSIO_AXI>, |
| <&clk IMX8MP_CLK_PCIE_ROOT>; |
| clock-names = "pcie", "pcie_bus", "pcie_aux"; |
| assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; |
| assigned-clock-rates = <10000000>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; /* eDMA */ |
| interrupt-names = "dma"; |
| fsl,max-link-speed = <3>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>; |
| resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>, |
| <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>; |
| reset-names = "apps", "turnoff"; |
| phys = <&pcie_phy>; |
| phy-names = "pcie-phy"; |
| num-ib-windows = <4>; |
| num-ob-windows = <4>; |
| status = "disabled"; |
| }; |
| |
| gpu3d: gpu@38000000 { |
| compatible = "vivante,gc"; |
| reg = <0x38000000 0x8000>; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPU3D_ROOT>, |
| <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>, |
| <&clk IMX8MP_CLK_GPU_ROOT>, |
| <&clk IMX8MP_CLK_GPU_AHB>; |
| clock-names = "core", "shader", "bus", "reg"; |
| assigned-clocks = <&clk IMX8MP_CLK_GPU3D_CORE>, |
| <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>, |
| <&clk IMX8MP_SYS_PLL1_800M>; |
| assigned-clock-rates = <800000000>, <800000000>; |
| power-domains = <&pgc_gpu3d>; |
| }; |
| |
| gpu2d: gpu@38008000 { |
| compatible = "vivante,gc"; |
| reg = <0x38008000 0x8000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_GPU2D_ROOT>, |
| <&clk IMX8MP_CLK_GPU_ROOT>, |
| <&clk IMX8MP_CLK_GPU_AHB>; |
| clock-names = "core", "bus", "reg"; |
| assigned-clocks = <&clk IMX8MP_CLK_GPU2D_CORE>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; |
| assigned-clock-rates = <800000000>; |
| power-domains = <&pgc_gpu2d>; |
| }; |
| |
| vpu_g1: video-codec@38300000 { |
| compatible = "nxp,imx8mm-vpu-g1"; |
| reg = <0x38300000 0x10000>; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>; |
| assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>; |
| assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>; |
| assigned-clock-rates = <600000000>; |
| power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G1>; |
| }; |
| |
| vpu_g2: video-codec@38310000 { |
| compatible = "nxp,imx8mq-vpu-g2"; |
| reg = <0x38310000 0x10000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>; |
| assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>; |
| assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>; |
| assigned-clock-rates = <500000000>; |
| power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G2>; |
| }; |
| |
| vpumix_blk_ctrl: blk-ctrl@38330000 { |
| compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon"; |
| reg = <0x38330000 0x100>; |
| #power-domain-cells = <1>; |
| power-domains = <&pgc_vpumix>, <&pgc_vpu_g1>, |
| <&pgc_vpu_g2>, <&pgc_vpu_vc8000e>; |
| power-domain-names = "bus", "g1", "g2", "vc8000e"; |
| clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>, |
| <&clk IMX8MP_CLK_VPU_G2_ROOT>, |
| <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>; |
| clock-names = "g1", "g2", "vc8000e"; |
| assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>, <&clk IMX8MP_VPU_PLL>; |
| assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>; |
| assigned-clock-rates = <600000000>, <600000000>; |
| interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>, |
| <&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>, |
| <&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>; |
| interconnect-names = "g1", "g2", "vc8000e"; |
| }; |
| |
| npu: npu@38500000 { |
| compatible = "vivante,gc"; |
| reg = <0x38500000 0x200000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MP_CLK_NPU_ROOT>, |
| <&clk IMX8MP_CLK_NPU_ROOT>, |
| <&clk IMX8MP_CLK_ML_AXI>, |
| <&clk IMX8MP_CLK_ML_AHB>; |
| clock-names = "core", "shader", "bus", "reg"; |
| power-domains = <&pgc_mlmix>; |
| }; |
| |
| gic: interrupt-controller@38800000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x38800000 0x10000>, |
| <0x38880000 0xc0000>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| edacmc: memory-controller@3d400000 { |
| compatible = "snps,ddrc-3.80a"; |
| reg = <0x3d400000 0x400000>; |
| interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| ddr-pmu@3d800000 { |
| compatible = "fsl,imx8mp-ddr-pmu", "fsl,imx8m-ddr-pmu"; |
| reg = <0x3d800000 0x400000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| usb3_phy0: usb-phy@381f0040 { |
| compatible = "fsl,imx8mp-usb-phy"; |
| reg = <0x381f0040 0x40>; |
| clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>; |
| clock-names = "phy"; |
| assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MP_CLK_24M>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB_PHY1>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usb3_0: usb@32f10100 { |
| compatible = "fsl,imx8mp-dwc3"; |
| reg = <0x32f10100 0x8>, |
| <0x381f0000 0x20>; |
| clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, |
| <&clk IMX8MP_CLK_USB_SUSP>; |
| clock-names = "hsio", "suspend"; |
| interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| dma-ranges = <0x40000000 0x40000000 0xc0000000>; |
| ranges; |
| status = "disabled"; |
| |
| usb_dwc3_0: usb@38100000 { |
| compatible = "snps,dwc3"; |
| reg = <0x38100000 0x10000>; |
| clocks = <&clk IMX8MP_CLK_USB_ROOT>, |
| <&clk IMX8MP_CLK_USB_CORE_REF>, |
| <&clk IMX8MP_CLK_USB_SUSP>; |
| clock-names = "bus_early", "ref", "suspend"; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb3_phy0>, <&usb3_phy0>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| snps,gfladj-refclk-lpm-sel-quirk; |
| snps,parkmode-disable-ss-quirk; |
| }; |
| |
| }; |
| |
| usb3_phy1: usb-phy@382f0040 { |
| compatible = "fsl,imx8mp-usb-phy"; |
| reg = <0x382f0040 0x40>; |
| clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>; |
| clock-names = "phy"; |
| assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MP_CLK_24M>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB_PHY2>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usb3_1: usb@32f10108 { |
| compatible = "fsl,imx8mp-dwc3"; |
| reg = <0x32f10108 0x8>, |
| <0x382f0000 0x20>; |
| clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, |
| <&clk IMX8MP_CLK_USB_SUSP>; |
| clock-names = "hsio", "suspend"; |
| interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| dma-ranges = <0x40000000 0x40000000 0xc0000000>; |
| ranges; |
| status = "disabled"; |
| |
| usb_dwc3_1: usb@38200000 { |
| compatible = "snps,dwc3"; |
| reg = <0x38200000 0x10000>; |
| clocks = <&clk IMX8MP_CLK_USB_ROOT>, |
| <&clk IMX8MP_CLK_USB_CORE_REF>, |
| <&clk IMX8MP_CLK_USB_SUSP>; |
| clock-names = "bus_early", "ref", "suspend"; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb3_phy1>, <&usb3_phy1>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| snps,gfladj-refclk-lpm-sel-quirk; |
| snps,parkmode-disable-ss-quirk; |
| }; |
| }; |
| |
| dsp: dsp@3b6e8000 { |
| compatible = "fsl,imx8mp-dsp"; |
| reg = <0x3b6e8000 0x88000>; |
| mbox-names = "txdb0", "txdb1", |
| "rxdb0", "rxdb1"; |
| mboxes = <&mu2 2 0>, <&mu2 2 1>, |
| <&mu2 3 0>, <&mu2 3 1>; |
| memory-region = <&dsp_reserved>; |
| status = "disabled"; |
| }; |
| }; |
| }; |