| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| /* |
| * Copyright 2022 Toradex |
| */ |
| |
| #include <dt-bindings/phy/phy-imx8-pcie.h> |
| #include <dt-bindings/pwm/pwm.h> |
| #include "imx8mp.dtsi" |
| |
| / { |
| chosen { |
| stdout-path = &uart3; |
| }; |
| |
| aliases { |
| /* Ethernet aliases to ensure correct MAC addresses */ |
| ethernet0 = &eqos; |
| ethernet1 = &fec; |
| rtc0 = &rtc_i2c; |
| rtc1 = &snvs_rtc; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| brightness-levels = <0 45 63 88 119 158 203 255>; |
| default-brightness-level = <4>; |
| /* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */ |
| enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>; |
| power-supply = <®_3p3v>; |
| /* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */ |
| pwms = <&pwm3 0 6666667 PWM_POLARITY_INVERTED>; |
| status = "disabled"; |
| }; |
| |
| backlight_mezzanine: backlight-mezzanine { |
| compatible = "pwm-backlight"; |
| brightness-levels = <0 45 63 88 119 158 203 255>; |
| default-brightness-level = <4>; |
| /* Verdin GPIO 4 (SODIMM 212) */ |
| enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| /* Verdin PWM_2 (SODIMM 16) */ |
| pwms = <&pwm2 0 6666667 PWM_POLARITY_INVERTED>; |
| status = "disabled"; |
| }; |
| |
| connector { |
| compatible = "gpio-usb-b-connector", "usb-b-connector"; |
| id-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; |
| label = "Type-C"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb_1_id>; |
| self-powered; |
| type = "micro"; |
| vbus-supply = <®_usb1_vbus>; |
| |
| port { |
| usb_dr_connector: endpoint { |
| remote-endpoint = <&usb3_dwc>; |
| }; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_keys>; |
| |
| key-wakeup { |
| debounce-interval = <10>; |
| /* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */ |
| gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; |
| label = "Wake-Up"; |
| linux,code = <KEY_WAKEUP>; |
| wakeup-source; |
| }; |
| }; |
| |
| /* Carrier Board Supplies */ |
| reg_1p8v: regulator-1p8v { |
| compatible = "regulator-fixed"; |
| regulator-max-microvolt = <1800000>; |
| regulator-min-microvolt = <1800000>; |
| regulator-name = "+V1.8_SW"; |
| }; |
| |
| reg_3p3v: regulator-3p3v { |
| compatible = "regulator-fixed"; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "+V3.3_SW"; |
| }; |
| |
| reg_5p0v: regulator-5p0v { |
| compatible = "regulator-fixed"; |
| regulator-max-microvolt = <5000000>; |
| regulator-min-microvolt = <5000000>; |
| regulator-name = "+V5_SW"; |
| }; |
| |
| /* Non PMIC On-module Supplies */ |
| reg_module_eth1phy: regulator-module-eth1phy { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */ |
| off-on-delay-us = <500000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_eth>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "On-module +V3.3_ETH"; |
| startup-delay-us = <200000>; |
| vin-supply = <®_vdd_3v3>; |
| }; |
| |
| /* |
| * By default we enable CTRL_SLEEP_MOCI#, this is required to have |
| * peripherals on the carrier board powered. |
| * If more granularity or power saving is required this can be disabled |
| * in the carrier board device tree files. |
| */ |
| reg_force_sleep_moci: regulator-force-sleep-moci { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| /* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */ |
| gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-name = "CTRL_SLEEP_MOCI#"; |
| }; |
| |
| reg_usb1_vbus: regulator-usb1-vbus { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| /* Verdin USB_1_EN (SODIMM 155) */ |
| gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb1_vbus>; |
| regulator-max-microvolt = <5000000>; |
| regulator-min-microvolt = <5000000>; |
| regulator-name = "USB_1_EN"; |
| }; |
| |
| reg_usb2_vbus: regulator-usb2-vbus { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| /* Verdin USB_2_EN (SODIMM 185) */ |
| gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2_vbus>; |
| regulator-max-microvolt = <5000000>; |
| regulator-min-microvolt = <5000000>; |
| regulator-name = "USB_2_EN"; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2 { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| /* Verdin SD_1_PWR_EN (SODIMM 76) */ |
| gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; |
| off-on-delay-us = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2_pwr_en>; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "+V3.3_SD"; |
| startup-delay-us = <2000>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| /* Use the kernel configuration settings instead */ |
| /delete-node/ linux,cma; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <®_vdd_arm>; |
| }; |
| |
| &A53_1 { |
| cpu-supply = <®_vdd_arm>; |
| }; |
| |
| &A53_2 { |
| cpu-supply = <®_vdd_arm>; |
| }; |
| |
| &A53_3 { |
| cpu-supply = <®_vdd_arm>; |
| }; |
| |
| &cpu_alert0 { |
| temperature = <95000>; |
| }; |
| |
| &cpu_crit0 { |
| temperature = <105000>; |
| }; |
| |
| /* Verdin SPI_1 */ |
| &ecspi1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1>; |
| }; |
| |
| /* Verdin ETH_1 (On-module PHY) */ |
| &eqos { |
| phy-handle = <ðphy0>; |
| phy-mode = "rgmii-id"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos>; |
| snps,force_thresh_dma_mode; |
| snps,mtl-rx-config = <&mtl_rx_setup>; |
| snps,mtl-tx-config = <&mtl_tx_setup>; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@7 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| eee-broken-100tx; |
| eee-broken-1000t; |
| interrupt-parent = <&gpio1>; |
| interrupts = <10 IRQ_TYPE_LEVEL_LOW>; |
| micrel,led-mode = <0>; |
| reg = <7>; |
| }; |
| }; |
| |
| mtl_rx_setup: rx-queues-config { |
| snps,rx-queues-to-use = <5>; |
| |
| queue0 { |
| snps,dcb-algorithm; |
| snps,priority = <0x1>; |
| snps,map-to-dma-channel = <0>; |
| }; |
| |
| queue1 { |
| snps,dcb-algorithm; |
| snps,priority = <0x2>; |
| snps,map-to-dma-channel = <1>; |
| }; |
| |
| queue2 { |
| snps,dcb-algorithm; |
| snps,priority = <0x4>; |
| snps,map-to-dma-channel = <2>; |
| }; |
| |
| queue3 { |
| snps,dcb-algorithm; |
| snps,priority = <0x8>; |
| snps,map-to-dma-channel = <3>; |
| }; |
| |
| queue4 { |
| snps,dcb-algorithm; |
| snps,priority = <0xf0>; |
| snps,map-to-dma-channel = <4>; |
| }; |
| }; |
| |
| mtl_tx_setup: tx-queues-config { |
| snps,tx-queues-to-use = <5>; |
| |
| queue0 { |
| snps,dcb-algorithm; |
| snps,priority = <0x1>; |
| }; |
| |
| queue1 { |
| snps,dcb-algorithm; |
| snps,priority = <0x2>; |
| }; |
| |
| queue2 { |
| snps,dcb-algorithm; |
| snps,priority = <0x4>; |
| }; |
| |
| queue3 { |
| snps,dcb-algorithm; |
| snps,priority = <0x8>; |
| }; |
| |
| queue4 { |
| snps,dcb-algorithm; |
| snps,priority = <0xf0>; |
| }; |
| }; |
| }; |
| |
| /* Verdin ETH_2_RGMII */ |
| &fec { |
| fsl,magic-packet; |
| phy-handle = <ðphy1>; |
| phy-mode = "rgmii-id"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_fec>; |
| pinctrl-1 = <&pinctrl_fec_sleep>; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy1: ethernet-phy@7 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| interrupt-parent = <&gpio4>; |
| interrupts = <18 IRQ_TYPE_LEVEL_LOW>; |
| micrel,led-mode = <0>; |
| reg = <7>; |
| }; |
| }; |
| }; |
| |
| /* Verdin CAN_1 */ |
| &flexcan1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| status = "disabled"; |
| }; |
| |
| /* Verdin CAN_2 */ |
| &flexcan2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2>; |
| status = "disabled"; |
| }; |
| |
| /* Verdin QSPI_1 */ |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi0>; |
| }; |
| |
| &gpio1 { |
| gpio-line-names = "SODIMM_206", |
| "SODIMM_208", |
| "", |
| "", |
| "", |
| "SODIMM_210", |
| "SODIMM_212", |
| "SODIMM_216", |
| "SODIMM_218", |
| "", |
| "", |
| "SODIMM_16", |
| "SODIMM_155", |
| "SODIMM_157", |
| "SODIMM_185", |
| "SODIMM_91"; |
| }; |
| |
| &gpio2 { |
| gpio-line-names = "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "SODIMM_143", |
| "SODIMM_141", |
| "", |
| "", |
| "SODIMM_161", |
| "", |
| "SODIMM_84", |
| "SODIMM_78", |
| "SODIMM_74", |
| "SODIMM_80", |
| "SODIMM_82", |
| "SODIMM_70", |
| "SODIMM_72"; |
| }; |
| |
| &gpio3 { |
| gpio-line-names = "SODIMM_52", |
| "SODIMM_54", |
| "", |
| "", |
| "", |
| "", |
| "SODIMM_56", |
| "SODIMM_58", |
| "SODIMM_60", |
| "SODIMM_62", |
| "", |
| "", |
| "", |
| "", |
| "SODIMM_66", |
| "", |
| "SODIMM_64", |
| "", |
| "", |
| "SODIMM_34", |
| "SODIMM_19", |
| "", |
| "SODIMM_32", |
| "", |
| "", |
| "SODIMM_30", |
| "SODIMM_59", |
| "SODIMM_57", |
| "SODIMM_63", |
| "SODIMM_61"; |
| }; |
| |
| &gpio4 { |
| gpio-line-names = "SODIMM_252", |
| "SODIMM_222", |
| "SODIMM_36", |
| "SODIMM_220", |
| "SODIMM_193", |
| "SODIMM_191", |
| "SODIMM_201", |
| "SODIMM_203", |
| "SODIMM_205", |
| "SODIMM_207", |
| "SODIMM_199", |
| "SODIMM_197", |
| "SODIMM_221", |
| "SODIMM_219", |
| "SODIMM_217", |
| "SODIMM_215", |
| "SODIMM_211", |
| "SODIMM_213", |
| "SODIMM_189", |
| "SODIMM_244", |
| "SODIMM_38", |
| "", |
| "SODIMM_76", |
| "SODIMM_135", |
| "SODIMM_133", |
| "SODIMM_17", |
| "SODIMM_24", |
| "SODIMM_26", |
| "SODIMM_21", |
| "SODIMM_256", |
| "SODIMM_48", |
| "SODIMM_44"; |
| }; |
| |
| /* Verdin HDMI_1 */ |
| &hdmi_tx { |
| ddc-i2c-bus = <&i2c5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hdmi>; |
| }; |
| |
| /* On-module I2C */ |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| pca9450: pmic@25 { |
| compatible = "nxp,pca9450c"; |
| interrupt-parent = <&gpio1>; |
| /* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */ |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| reg = <0x25>; |
| |
| /* |
| * The bootloader is expected to switch on LDO4 for the on-module +V3.3_ADC and the |
| * I2C level shifter for the TLA2024 ADC behind this PMIC. |
| */ |
| |
| regulators { |
| BUCK1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1000000>; |
| regulator-min-microvolt = <720000>; |
| regulator-name = "On-module +VDD_SOC (BUCK1)"; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| reg_vdd_arm: BUCK2 { |
| nxp,dvs-run-voltage = <950000>; |
| nxp,dvs-standby-voltage = <850000>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1025000>; |
| regulator-min-microvolt = <720000>; |
| regulator-name = "On-module +VDD_ARM (BUCK2)"; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| reg_vdd_3v3: BUCK4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "On-module +V3.3 (BUCK4)"; |
| }; |
| |
| reg_vdd_1v8: BUCK5 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1800000>; |
| regulator-min-microvolt = <1800000>; |
| regulator-name = "PWR_1V8_MOCI (BUCK5)"; |
| }; |
| |
| BUCK6 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1155000>; |
| regulator-min-microvolt = <1045000>; |
| regulator-name = "On-module +VDD_DDR (BUCK6)"; |
| }; |
| |
| LDO1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1950000>; |
| regulator-min-microvolt = <1650000>; |
| regulator-name = "On-module +V1.8_SNVS (LDO1)"; |
| }; |
| |
| LDO2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1150000>; |
| regulator-min-microvolt = <800000>; |
| regulator-name = "On-module +V0.8_SNVS (LDO2)"; |
| }; |
| |
| LDO3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <1800000>; |
| regulator-min-microvolt = <1800000>; |
| regulator-name = "On-module +V1.8A (LDO3)"; |
| }; |
| |
| LDO4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <3300000>; |
| regulator-name = "On-module +V3.3_ADC (LDO4)"; |
| }; |
| |
| reg_vdd_sdio: LDO5 { |
| regulator-max-microvolt = <3300000>; |
| regulator-min-microvolt = <1800000>; |
| regulator-name = "On-module +V3.3_1.8_SD (LDO5)"; |
| }; |
| }; |
| }; |
| |
| rtc_i2c: rtc@32 { |
| compatible = "epson,rx8130"; |
| reg = <0x32>; |
| }; |
| |
| /* On-module temperature sensor */ |
| hwmon_temp_module: sensor@48 { |
| compatible = "ti,tmp1075"; |
| reg = <0x48>; |
| vs-supply = <®_vdd_1v8>; |
| }; |
| |
| adc@49 { |
| compatible = "ti,ads1015"; |
| reg = <0x49>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* Verdin I2C_1 (ADC_4 - ADC_3) */ |
| channel@0 { |
| reg = <0>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 (ADC_4 - ADC_1) */ |
| channel@1 { |
| reg = <1>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 (ADC_3 - ADC_1) */ |
| channel@2 { |
| reg = <2>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 (ADC_2 - ADC_1) */ |
| channel@3 { |
| reg = <3>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 ADC_4 */ |
| channel@4 { |
| reg = <4>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 ADC_3 */ |
| channel@5 { |
| reg = <5>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 ADC_2 */ |
| channel@6 { |
| reg = <6>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| |
| /* Verdin I2C_1 ADC_1 */ |
| channel@7 { |
| reg = <7>; |
| ti,datarate = <4>; |
| ti,gain = <2>; |
| }; |
| }; |
| |
| eeprom@50 { |
| compatible = "st,24c02"; |
| pagesize = <16>; |
| reg = <0x50>; |
| }; |
| }; |
| |
| /* Verdin I2C_2_DSI */ |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| pinctrl-1 = <&pinctrl_i2c2_gpio>; |
| scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| |
| atmel_mxt_ts_mezzanine: touch-mezzanine@4a { |
| compatible = "atmel,maxtouch"; |
| /* Verdin GPIO_3 (SODIMM 210) */ |
| interrupt-parent = <&gpio1>; |
| interrupts = <5 IRQ_TYPE_EDGE_FALLING>; |
| reg = <0x4a>; |
| /* Verdin GPIO_2 (SODIMM 208) */ |
| reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; |
| status = "disabled"; |
| }; |
| }; |
| |
| /* Verdin I2C_4_CSI */ |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| pinctrl-1 = <&pinctrl_i2c3_gpio>; |
| scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| }; |
| |
| /* Verdin I2C_1 */ |
| &i2c4 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c4>; |
| pinctrl-1 = <&pinctrl_i2c4_gpio>; |
| scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| |
| gpio_expander_21: gpio-expander@21 { |
| compatible = "nxp,pcal6416"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0x21>; |
| vcc-supply = <®_3p3v>; |
| status = "disabled"; |
| }; |
| |
| lvds_ti_sn65dsi84: bridge@2c { |
| compatible = "ti,sn65dsi84"; |
| /* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */ |
| /* Verdin GPIO_10_DSI (SODIMM 21) */ |
| enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_10_dsi>; |
| reg = <0x2c>; |
| status = "disabled"; |
| }; |
| |
| /* Current measurement into module VCC */ |
| hwmon: hwmon@40 { |
| compatible = "ti,ina219"; |
| reg = <0x40>; |
| shunt-resistor = <10000>; |
| status = "disabled"; |
| }; |
| |
| hdmi_lontium_lt8912: hdmi@48 { |
| compatible = "lontium,lt8912b"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>; |
| reg = <0x48>; |
| /* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */ |
| /* Verdin GPIO_10_DSI (SODIMM 21) */ |
| reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>; |
| status = "disabled"; |
| }; |
| |
| atmel_mxt_ts: touch@4a { |
| compatible = "atmel,maxtouch"; |
| /* |
| * Verdin GPIO_9_DSI |
| * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI84 IRQ albeit currently unused) |
| */ |
| interrupt-parent = <&gpio4>; |
| interrupts = <25 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>; |
| reg = <0x4a>; |
| /* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */ |
| reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; |
| status = "disabled"; |
| }; |
| |
| /* Temperature sensor on carrier board */ |
| hwmon_temp: sensor@4f { |
| compatible = "ti,tmp75c"; |
| reg = <0x4f>; |
| status = "disabled"; |
| }; |
| |
| /* EEPROM on display adapter (MIPI DSI Display Adapter) */ |
| eeprom_display_adapter: eeprom@50 { |
| compatible = "st,24c02"; |
| pagesize = <16>; |
| reg = <0x50>; |
| status = "disabled"; |
| }; |
| |
| /* EEPROM on carrier board */ |
| eeprom_carrier_board: eeprom@57 { |
| compatible = "st,24c02"; |
| pagesize = <16>; |
| reg = <0x57>; |
| status = "disabled"; |
| }; |
| }; |
| |
| /* Verdin I2C_3_HDMI */ |
| &i2c5 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c5>; |
| pinctrl-1 = <&pinctrl_i2c5_gpio>; |
| scl-gpios = <&gpio3 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio3 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| }; |
| |
| /* Verdin PCIE_1 */ |
| &pcie { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie>; |
| /* PCIE_1_RESET# (SODIMM 244) */ |
| reset-gpio = <&gpio4 19 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &pcie_phy { |
| clocks = <&hsio_blk_ctrl>; |
| clock-names = "ref"; |
| fsl,clkreq-unsupported; |
| fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>; |
| }; |
| |
| /* Verdin PWM_1 */ |
| &pwm1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm_1>; |
| #pwm-cells = <3>; |
| }; |
| |
| /* Verdin PWM_2 */ |
| &pwm2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm_2>; |
| #pwm-cells = <3>; |
| }; |
| |
| /* Verdin PWM_3_DSI */ |
| &pwm3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm_3>; |
| #pwm-cells = <3>; |
| }; |
| |
| /* TODO: Verdin I2S_1 */ |
| |
| /* TODO: Verdin I2S_2 */ |
| |
| &snvs_pwrkey { |
| status = "okay"; |
| }; |
| |
| /* Verdin UART_1 */ |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| uart-has-rtscts; |
| }; |
| |
| /* Verdin UART_2 */ |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| uart-has-rtscts; |
| }; |
| |
| /* Verdin UART_3, used as the Linux Console */ |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| }; |
| |
| /* Verdin UART_4, used for Bluetooth on Wi-Fi/Bluetooth SKUs */ |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| }; |
| |
| /* Verdin USB_1 */ |
| &usb3_0 { |
| fsl,disable-port-power-control; |
| fsl,over-current-active-low; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb_1_oc_n>; |
| }; |
| |
| &usb_dwc3_0 { |
| /* dual role only, not full featured OTG */ |
| adp-disable; |
| dr_mode = "otg"; |
| hnp-disable; |
| maximum-speed = "high-speed"; |
| role-switch-default-mode = "peripheral"; |
| srp-disable; |
| usb-role-switch; |
| |
| port { |
| usb3_dwc: endpoint { |
| remote-endpoint = <&usb_dr_connector>; |
| }; |
| }; |
| }; |
| |
| /* Verdin USB_2 */ |
| &usb3_1 { |
| fsl,disable-port-power-control; |
| }; |
| |
| &usb3_phy1 { |
| vbus-supply = <®_usb2_vbus>; |
| }; |
| |
| &usb_dwc3_1 { |
| dr_mode = "host"; |
| }; |
| |
| /* Verdin SD_1 */ |
| &usdhc2 { |
| assigned-clocks = <&clk IMX8MP_CLK_USDHC2>; |
| assigned-clock-rates = <400000000>; |
| bus-width = <4>; |
| cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| disable-wp; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>; |
| pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| vqmmc-supply = <®_vdd_sdio>; |
| }; |
| |
| /* On-module eMMC */ |
| &usdhc3 { |
| assigned-clocks = <&clk IMX8MP_CLK_USDHC3_ROOT>; |
| assigned-clock-rates = <400000000>; |
| bus-width = <8>; |
| non-removable; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| fsl,ext-reset-output; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_bt_uart: btuartgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_ECSPI2_MISO__UART4_DCE_CTS 0x1c4>, |
| <MX8MP_IOMUXC_ECSPI2_MOSI__UART4_DCE_TX 0x1c4>, |
| <MX8MP_IOMUXC_ECSPI2_SCLK__UART4_DCE_RX 0x1c4>, |
| <MX8MP_IOMUXC_ECSPI2_SS0__UART4_DCE_RTS 0x1c4>; |
| }; |
| |
| pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x1c4>; /* SODIMM 256 */ |
| }; |
| |
| pinctrl_ecspi1: ecspi1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x1c4>, /* SODIMM 198 */ |
| <MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x4>, /* SODIMM 200 */ |
| <MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x4>, /* SODIMM 196 */ |
| <MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09 0x1c4>; /* SODIMM 202 */ |
| }; |
| |
| /* Connection On Board PHY */ |
| pinctrl_eqos: eqosgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3>, |
| <MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3>, |
| <MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91>, |
| <MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91>, |
| <MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91>, |
| <MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91>, |
| <MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91>, |
| <MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91>, |
| <MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f>, |
| <MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f>, |
| <MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f>, |
| <MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f>, |
| <MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f>, |
| <MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f>; |
| }; |
| |
| /* ETH_INT# shared with TPM_INT# (usually N/A) */ |
| pinctrl_eth_tpm_int: ethtpmintgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x1c4>; |
| }; |
| |
| /* Connection Carrier Board PHY ETH_2 */ |
| pinctrl_fec: fecgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3>, /* SODIMM 193 */ |
| <MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3>, /* SODIMM 191 */ |
| <MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91>, /* SODIMM 201 */ |
| <MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91>, /* SODIMM 203 */ |
| <MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91>, /* SODIMM 205 */ |
| <MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91>, /* SODIMM 207 */ |
| <MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91>, /* SODIMM 197 */ |
| <MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91>, /* SODIMM 199 */ |
| <MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f>, /* SODIMM 221 */ |
| <MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f>, /* SODIMM 219 */ |
| <MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f>, /* SODIMM 217 */ |
| <MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f>, /* SODIMM 215 */ |
| <MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f>, /* SODIMM 211 */ |
| <MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f>, /* SODIMM 213 */ |
| <MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x1c4>; /* SODIMM 189 */ |
| }; |
| |
| pinctrl_fec_sleep: fecsleepgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3>, /* SODIMM 193 */ |
| <MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3>, /* SODIMM 191 */ |
| <MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91>, /* SODIMM 201 */ |
| <MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91>, /* SODIMM 203 */ |
| <MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91>, /* SODIMM 205 */ |
| <MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91>, /* SODIMM 207 */ |
| <MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91>, /* SODIMM 197 */ |
| <MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91>, /* SODIMM 199 */ |
| <MX8MP_IOMUXC_SAI1_TXD0__GPIO4_IO12 0x1f>, /* SODIMM 221 */ |
| <MX8MP_IOMUXC_SAI1_TXD1__GPIO4_IO13 0x1f>, /* SODIMM 219 */ |
| <MX8MP_IOMUXC_SAI1_TXD2__GPIO4_IO14 0x1f>, /* SODIMM 217 */ |
| <MX8MP_IOMUXC_SAI1_TXD3__GPIO4_IO15 0x1f>, /* SODIMM 215 */ |
| <MX8MP_IOMUXC_SAI1_TXD4__GPIO4_IO16 0x1f>, /* SODIMM 211 */ |
| <MX8MP_IOMUXC_SAI1_TXD5__GPIO4_IO17 0x1f>, /* SODIMM 213 */ |
| <MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x184>; /* SODIMM 189 */ |
| }; |
| |
| pinctrl_flexcan1: flexcan1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154>, /* SODIMM 22 */ |
| <MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154>; /* SODIMM 20 */ |
| }; |
| |
| pinctrl_flexcan2: flexcan2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX 0x154>, /* SODIMM 26 */ |
| <MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX 0x154>; /* SODIMM 24 */ |
| }; |
| |
| pinctrl_flexspi0: flexspi0grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2>, /* SODIMM 52 */ |
| <MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82>, /* SODIMM 54 */ |
| <MX8MP_IOMUXC_NAND_DQS__FLEXSPI_A_DQS 0x82>, /* SODIMM 66 */ |
| <MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82>, /* SODIMM 56 */ |
| <MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82>, /* SODIMM 58 */ |
| <MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82>, /* SODIMM 60 */ |
| <MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82>, /* SODIMM 62 */ |
| <MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x82>; /* SODIMM 64 */ |
| }; |
| |
| pinctrl_gpio1: gpio1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00 0x184>; /* SODIMM 206 */ |
| }; |
| |
| pinctrl_gpio2: gpio2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01 0x1c4>; /* SODIMM 208 */ |
| }; |
| |
| pinctrl_gpio3: gpio3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x184>; /* SODIMM 210 */ |
| }; |
| |
| pinctrl_gpio4: gpio4grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x184>; /* SODIMM 212 */ |
| }; |
| |
| pinctrl_gpio5: gpio5grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x184>; /* SODIMM 216 */ |
| }; |
| |
| pinctrl_gpio6: gpio6grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08 0x184>; /* SODIMM 218 */ |
| }; |
| |
| pinctrl_gpio7: gpio7grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x184>; /* SODIMM 220 */ |
| }; |
| |
| pinctrl_gpio8: gpio8grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0x184>; /* SODIMM 222 */ |
| }; |
| |
| /* Verdin GPIO_9_DSI (pulled-up as active-low) */ |
| pinctrl_gpio_9_dsi: gpio9dsigrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25 0x1c4>; /* SODIMM 17 */ |
| }; |
| |
| /* Verdin GPIO_10_DSI */ |
| pinctrl_gpio_10_dsi: gpio10dsigrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x1c4>; /* SODIMM 21 */ |
| }; |
| |
| /* Non-wifi MSP usage only */ |
| pinctrl_gpio_hog1: gpiohog1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_ECSPI2_MISO__GPIO5_IO12 0x1c4>, /* SODIMM 116 */ |
| <MX8MP_IOMUXC_ECSPI2_MOSI__GPIO5_IO11 0x1c4>, /* SODIMM 152 */ |
| <MX8MP_IOMUXC_ECSPI2_SCLK__GPIO5_IO10 0x1c4>, /* SODIMM 164 */ |
| <MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x1c4>; /* SODIMM 128 */ |
| }; |
| |
| /* USB_2_OC# */ |
| pinctrl_gpio_hog2: gpiohog2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02 0x1c4>; /* SODIMM 187 */ |
| }; |
| |
| pinctrl_gpio_hog3: gpiohog3grp { |
| fsl,pins = |
| /* CSI_1_MCLK */ |
| <MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15 0x1c4>; /* SODIMM 91 */ |
| }; |
| |
| /* Wifi usage only */ |
| pinctrl_gpio_hog4: gpiohog4grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_UART4_RXD__GPIO5_IO28 0x1c4>, /* SODIMM 151 */ |
| <MX8MP_IOMUXC_UART4_TXD__GPIO5_IO29 0x1c4>; /* SODIMM 153 */ |
| }; |
| |
| pinctrl_gpio_keys: gpiokeysgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00 0x1c4>; /* SODIMM 252 */ |
| }; |
| |
| pinctrl_hdmi: hdmigrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x140>, /* SODIMM 63 */ |
| <MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x180>; /* SODIMM 61 */ |
| }; |
| |
| /* On-module I2C */ |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c6>, /* PMIC_I2C_SCL */ |
| <MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c6>; /* PMIC_I2C_SDA */ |
| }; |
| |
| pinctrl_i2c1_gpio: i2c1gpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x400001c6>, /* PMIC_I2C_SCL */ |
| <MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x400001c6>; /* PMIC_I2C_SDA */ |
| }; |
| |
| /* Verdin I2C_2_DSI */ |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c6>, /* SODIMM 55 */ |
| <MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c6>; /* SODIMM 53 */ |
| }; |
| |
| pinctrl_i2c2_gpio: i2c2gpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x400001c6>, /* SODIMM 55 */ |
| <MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x400001c6>; /* SODIMM 53 */ |
| }; |
| |
| /* Verdin I2C_4_CSI */ |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c6>, /* SODIMM 95 */ |
| <MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c6>; /* SODIMM 93 */ |
| }; |
| |
| pinctrl_i2c3_gpio: i2c3gpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18 0x400001c6>, /* SODIMM 95 */ |
| <MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19 0x400001c6>; /* SODIMM 93 */ |
| }; |
| |
| /* Verdin I2C_1 */ |
| pinctrl_i2c4: i2c4grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c6>, /* SODIMM 14 */ |
| <MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c6>; /* SODIMM 12 */ |
| }; |
| |
| pinctrl_i2c4_gpio: i2c4gpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20 0x400001c6>, /* SODIMM 14 */ |
| <MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21 0x400001c6>; /* SODIMM 12 */ |
| }; |
| |
| /* Verdin I2C_3_HDMI */ |
| pinctrl_i2c5: i2c5grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_HDMI_DDC_SCL__I2C5_SCL 0x400001c6>, /* SODIMM 59 */ |
| <MX8MP_IOMUXC_HDMI_DDC_SDA__I2C5_SDA 0x400001c6>; /* SODIMM 57 */ |
| }; |
| |
| pinctrl_i2c5_gpio: i2c5gpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_HDMI_DDC_SCL__GPIO3_IO26 0x400001c6>, /* SODIMM 59 */ |
| <MX8MP_IOMUXC_HDMI_DDC_SDA__GPIO3_IO27 0x400001c6>; /* SODIMM 57 */ |
| }; |
| |
| /* Verdin I2S_2_BCLK (TOUCH_RESET#) */ |
| pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00 0x184>; /* SODIMM 42 */ |
| }; |
| |
| /* Verdin I2S_2_D_OUT shared with SAI3 */ |
| pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01 0x184>; /* SODIMM 46 */ |
| }; |
| |
| pinctrl_pcie: pciegrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x4>, /* SODIMM 244 */ |
| <MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x1c4>; /* PMIC_EN_PCIe_CLK, unused */ |
| }; |
| |
| pinctrl_pmic: pmicirqgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x1c4>; /* PMIC_INT# */ |
| }; |
| |
| pinctrl_pwm_1: pwm1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT 0x6>; /* SODIMM 15 */ |
| }; |
| |
| pinctrl_pwm_2: pwm2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO11__PWM2_OUT 0x6>; /* SODIMM 16 */ |
| }; |
| |
| /* Verdin PWM_3_DSI shared with GPIO3_IO20 */ |
| pinctrl_pwm_3: pwm3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI5_RXC__PWM3_OUT 0x6>; /* SODIMM 19 */ |
| }; |
| |
| /* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM3_OUT */ |
| pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsi1hpdgpiogrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20 0x184>; /* SODIMM 19 */ |
| }; |
| |
| pinctrl_reg_eth: regethgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x184>; /* PMIC_EN_ETH */ |
| }; |
| |
| pinctrl_sai1: sai1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI1_MCLK__AUDIOMIX_SAI1_MCLK 0x96>, /* SODIMM 38 */ |
| <MX8MP_IOMUXC_SAI1_RXD0__AUDIOMIX_SAI1_RX_DATA00 0x1d6>, /* SODIMM 36 */ |
| <MX8MP_IOMUXC_SAI5_MCLK__AUDIOMIX_SAI1_TX_BCLK 0x1d6>, /* SODIMM 30 */ |
| <MX8MP_IOMUXC_SAI5_RXD1__AUDIOMIX_SAI1_TX_SYNC 0x1d6>, /* SODIMM 32 */ |
| <MX8MP_IOMUXC_SAI5_RXFS__AUDIOMIX_SAI1_TX_DATA00 0x96>; /* SODIMM 34 */ |
| }; |
| |
| pinctrl_sai3: sai3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI3_RXD__AUDIOMIX_SAI3_RX_DATA00 0x1d6>, /* SODIMM 48 */ |
| <MX8MP_IOMUXC_SAI3_TXC__AUDIOMIX_SAI3_TX_BCLK 0x1d6>, /* SODIMM 42 */ |
| <MX8MP_IOMUXC_SAI3_TXD__AUDIOMIX_SAI3_TX_DATA00 0x96>, /* SODIMM 46 */ |
| <MX8MP_IOMUXC_SAI3_TXFS__AUDIOMIX_SAI3_TX_SYNC 0x1d6>; /* SODIMM 44 */ |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS 0x1c4>, /* SODIMM 135 */ |
| <MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS 0x1c4>, /* SODIMM 133 */ |
| <MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x1c4>, /* SODIMM 129 */ |
| <MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x1c4>; /* SODIMM 131 */ |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_DATA4__UART2_DCE_RTS 0x1c4>, /* SODIMM 143 */ |
| <MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS 0x1c4>, /* SODIMM 141 */ |
| <MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x1c4>, /* SODIMM 137 */ |
| <MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x1c4>; /* SODIMM 139 */ |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x1c4>, /* SODIMM 147 */ |
| <MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x1c4>; /* SODIMM 149 */ |
| }; |
| |
| /* Non-wifi usage only */ |
| pinctrl_uart4: uart4grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x1c4>, /* SODIMM 151 */ |
| <MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x1c4>; /* SODIMM 153 */ |
| }; |
| |
| pinctrl_usb1_vbus: usb1vbusgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x106>; /* SODIMM 155 */ |
| }; |
| |
| /* USB_1_ID */ |
| pinctrl_usb_1_id: usb1idgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10 0x1c4>; /* SODIMM 161 */ |
| }; |
| |
| /* USB_1_OC# */ |
| pinctrl_usb_1_oc_n: usb1ocngrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC 0x1c4>; /* SODIMM 157 */ |
| }; |
| |
| pinctrl_usb2_vbus: usb2vbusgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14 0x106>; /* SODIMM 185 */ |
| }; |
| |
| /* On-module Wi-Fi */ |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190>, |
| <MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0>, |
| <MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0>, |
| <MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0>, |
| <MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0>, |
| <MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0>; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x194>, |
| <MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d4>, |
| <MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d4>, |
| <MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d4>, |
| <MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d4>, |
| <MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d4>; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x196>, |
| <MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d6>, |
| <MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d6>, |
| <MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d6>, |
| <MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d6>, |
| <MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d6>; |
| }; |
| |
| pinctrl_usdhc2_cd: usdhc2cdgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4>; /* SODIMM 84 */ |
| }; |
| |
| pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x0>; /* SODIMM 84 */ |
| }; |
| |
| pinctrl_usdhc2_pwr_en: usdhc2pwrengrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x4>; /* SODIMM 76 */ |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0x4>, /* PMIC_USDHC_VSELECT */ |
| <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190>, /* SODIMM 78 */ |
| <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0>, /* SODIMM 74 */ |
| <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0>, /* SODIMM 80 */ |
| <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0>, /* SODIMM 82 */ |
| <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0>, /* SODIMM 70 */ |
| <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0>; /* SODIMM 72 */ |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0x4>, |
| <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194>, |
| <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4>, |
| <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4>, |
| <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4>, |
| <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4>, |
| <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4>; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0x4>, |
| <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196>, |
| <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6>, |
| <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6>, |
| <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6>, |
| <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6>, |
| <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6>; |
| }; |
| |
| /* Avoid backfeeding with removed card power */ |
| pinctrl_usdhc2_sleep: usdhc2slpgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0x0>, |
| <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x100>, |
| <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x100>, |
| <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x100>, |
| <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x100>, |
| <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x100>, |
| <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x100>; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B 0x1d1>, |
| <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190>, |
| <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0>, |
| <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0>, |
| <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0>, |
| <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0>, |
| <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0>, |
| <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0>, |
| <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0>, |
| <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0>, |
| <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190>, |
| <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0>; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B 0x1d1>, |
| <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194>, |
| <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4>, |
| <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4>, |
| <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4>, |
| <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4>, |
| <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4>, |
| <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4>, |
| <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4>, |
| <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4>, |
| <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194>, |
| <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4>; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B 0x1d1>, |
| <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196>, |
| <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d2>, |
| <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d2>, |
| <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d2>, |
| <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d2>, |
| <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d2>, |
| <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d2>, |
| <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d2>, |
| <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d2>, |
| <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196>, |
| <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6>; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6>; /* PMIC_WDI */ |
| }; |
| |
| pinctrl_bluetooth_ctrl: bluetoothctrlgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08 0x1c4>; /* WIFI_WKUP_BT */ |
| }; |
| |
| pinctrl_wifi_ctrl: wifictrlgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09 0x1c4>; /* WIFI_WKUP_WLAN */ |
| }; |
| |
| pinctrl_wifi_i2s: wifii2sgrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x1d6>, /* WIFI_TX_SYNC */ |
| <MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21 0x96>, /* WIFI_RX_DATA0 */ |
| <MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23 0x1d6>, /* WIFI_TX_BCLK */ |
| <MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24 0x1d6>; /* WIFI_TX_DATA0 */ |
| }; |
| |
| pinctrl_wifi_pwr_en: wifipwrengrp { |
| fsl,pins = |
| <MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11 0x184>; /* PMIC_EN_WIFI */ |
| }; |
| }; |
