| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2019 BayLibre SAS. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include "meson-sm1.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/meson-g12a-gpio.h> |
| |
| / { |
| compatible = "seirobotics,sei610", "amlogic,sm1"; |
| model = "SEI Robotics SEI610"; |
| |
| aliases { |
| serial0 = &uart_AO; |
| ethernet0 = ðmac; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys-polled"; |
| poll-interval = <100>; |
| |
| key1 { |
| label = "A"; |
| linux,code = <BTN_0>; |
| gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>; |
| }; |
| |
| key2 { |
| label = "B"; |
| linux,code = <BTN_1>; |
| gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>; |
| }; |
| |
| key3 { |
| label = "C"; |
| linux,code = <BTN_2>; |
| gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| hdmi-connector { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&hdmi_tx_tmds_out>; |
| }; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| bluetooth { |
| label = "sei610:blue:bt"; |
| gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; |
| default-state = "off"; |
| }; |
| }; |
| |
| pwmleds { |
| compatible = "pwm-leds"; |
| |
| power { |
| label = "sei610:red:power"; |
| pwms = <&pwm_AO_ab 0 30518 0>; |
| max-brightness = <255>; |
| linux,default-trigger = "default-on"; |
| active-low; |
| }; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x40000000>; |
| }; |
| |
| ao_5v: regulator-ao_5v { |
| compatible = "regulator-fixed"; |
| regulator-name = "AO_5V"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&dc_in>; |
| regulator-always-on; |
| }; |
| |
| dc_in: regulator-dc_in { |
| compatible = "regulator-fixed"; |
| regulator-name = "DC_IN"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| emmc_1v8: regulator-emmc_1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "EMMC_1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vddao_3v3>; |
| regulator-always-on; |
| }; |
| |
| vddao_3v3: regulator-vddao_3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDAO_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&dc_in>; |
| regulator-always-on; |
| }; |
| |
| /* Used by Tuner, RGB Led & IR Emitter LED array */ |
| vddao_3v3_t: regulator-vddao_3v3_t { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDAO_3V3_T"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vddao_3v3>; |
| gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>; |
| enable-active-low; |
| regulator-always-on; |
| }; |
| |
| vddcpu: regulator-vddcpu { |
| /* |
| * SY8120B1ABC DC/DC Regulator. |
| */ |
| compatible = "pwm-regulator"; |
| |
| regulator-name = "VDDCPU"; |
| regulator-min-microvolt = <690000>; |
| regulator-max-microvolt = <1050000>; |
| |
| vin-supply = <&dc_in>; |
| |
| pwms = <&pwm_AO_cd 1 1500 0>; |
| pwm-dutycycle-range = <100 0>; |
| |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vddio_ao1v8: regulator-vddio_ao1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDIO_AO1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vddao_3v3>; |
| regulator-always-on; |
| }; |
| |
| reserved-memory { |
| /* TEE Reserved Memory */ |
| bl32_reserved: bl32@5000000 { |
| reg = <0x0 0x05300000 0x0 0x2000000>; |
| no-map; |
| }; |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; |
| clocks = <&wifi32k>; |
| clock-names = "ext_clock"; |
| }; |
| |
| wifi32k: wifi32k { |
| compatible = "pwm-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ |
| }; |
| }; |
| |
| &cec_AO { |
| pinctrl-0 = <&cec_ao_a_h_pins>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| hdmi-phandle = <&hdmi_tx>; |
| }; |
| |
| &cecb_AO { |
| pinctrl-0 = <&cec_ao_b_h_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| hdmi-phandle = <&hdmi_tx>; |
| }; |
| |
| &cpu0 { |
| cpu-supply = <&vddcpu>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPU_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu1 { |
| cpu-supply = <&vddcpu>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPU1_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu2 { |
| cpu-supply = <&vddcpu>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPU2_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu3 { |
| cpu-supply = <&vddcpu>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPU3_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| ðmac { |
| status = "okay"; |
| phy-handle = <&internal_ephy>; |
| phy-mode = "rmii"; |
| }; |
| |
| &hdmi_tx { |
| status = "okay"; |
| pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &hdmi_tx_tmds_port { |
| hdmi_tx_tmds_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| |
| &i2c3 { |
| status = "okay"; |
| pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &ir { |
| status = "okay"; |
| pinctrl-0 = <&remote_input_ao_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &pwm_AO_ab { |
| status = "okay"; |
| pinctrl-0 = <&pwm_ao_a_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin0"; |
| }; |
| |
| &pwm_AO_cd { |
| pinctrl-0 = <&pwm_ao_d_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin1"; |
| status = "okay"; |
| }; |
| |
| &pwm_ef { |
| status = "okay"; |
| pinctrl-0 = <&pwm_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin0"; |
| }; |
| |
| &saradc { |
| status = "okay"; |
| vref-supply = <&vddio_ao1v8>; |
| }; |
| |
| /* SDIO */ |
| &sd_emmc_a { |
| status = "okay"; |
| pinctrl-0 = <&sdio_pins>; |
| pinctrl-1 = <&sdio_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| sd-uhs-sdr50; |
| max-frequency = <100000000>; |
| |
| non-removable; |
| disable-wp; |
| |
| mmc-pwrseq = <&sdio_pwrseq>; |
| |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vddio_ao1v8>; |
| |
| brcmf: wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| }; |
| }; |
| |
| /* SD card */ |
| &sd_emmc_b { |
| status = "okay"; |
| pinctrl-0 = <&sdcard_c_pins>; |
| pinctrl-1 = <&sdcard_clk_gate_c_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <50000000>; |
| disable-wp; |
| |
| cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vddao_3v3>; |
| }; |
| |
| /* eMMC */ |
| &sd_emmc_c { |
| status = "okay"; |
| pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; |
| pinctrl-1 = <&emmc_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| mmc-hs200-1_8v; |
| max-frequency = <200000000>; |
| non-removable; |
| disable-wp; |
| |
| mmc-pwrseq = <&emmc_pwrseq>; |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&emmc_1v8>; |
| }; |
| |
| &uart_A { |
| status = "okay"; |
| pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; |
| pinctrl-names = "default"; |
| uart-has-rtscts; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; |
| max-speed = <2000000>; |
| clocks = <&wifi32k>; |
| clock-names = "lpo"; |
| vbat-supply = <&vddao_3v3>; |
| vddio-supply = <&vddio_ao1v8>; |
| }; |
| }; |
| |
| /* Exposed via the on-board USB to Serial FT232RL IC */ |
| &uart_AO { |
| status = "okay"; |
| pinctrl-0 = <&uart_ao_a_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &usb { |
| status = "okay"; |
| dr_mode = "otg"; |
| }; |
