| // SPDX-License-Identifier: GPL-2.0 |
| /* Driver for the Texas Instruments DP83869 PHY |
| * Copyright (C) 2019 Texas Instruments Inc. |
| */ |
| |
| #include <linux/ethtool.h> |
| #include <linux/kernel.h> |
| #include <linux/mii.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/phy.h> |
| #include <linux/delay.h> |
| |
| #include <dt-bindings/net/ti-dp83869.h> |
| |
| #define DP83869_PHY_ID 0x2000a0f1 |
| #define DP83869_DEVADDR 0x1f |
| |
| #define MII_DP83869_PHYCTRL 0x10 |
| #define MII_DP83869_MICR 0x12 |
| #define MII_DP83869_ISR 0x13 |
| #define DP83869_CTRL 0x1f |
| #define DP83869_CFG4 0x1e |
| |
| /* Extended Registers */ |
| #define DP83869_GEN_CFG3 0x0031 |
| #define DP83869_RGMIICTL 0x0032 |
| #define DP83869_STRAP_STS1 0x006e |
| #define DP83869_RGMIIDCTL 0x0086 |
| #define DP83869_IO_MUX_CFG 0x0170 |
| #define DP83869_OP_MODE 0x01df |
| #define DP83869_FX_CTRL 0x0c00 |
| |
| #define DP83869_SW_RESET BIT(15) |
| #define DP83869_SW_RESTART BIT(14) |
| |
| /* MICR Interrupt bits */ |
| #define MII_DP83869_MICR_AN_ERR_INT_EN BIT(15) |
| #define MII_DP83869_MICR_SPEED_CHNG_INT_EN BIT(14) |
| #define MII_DP83869_MICR_DUP_MODE_CHNG_INT_EN BIT(13) |
| #define MII_DP83869_MICR_PAGE_RXD_INT_EN BIT(12) |
| #define MII_DP83869_MICR_AUTONEG_COMP_INT_EN BIT(11) |
| #define MII_DP83869_MICR_LINK_STS_CHNG_INT_EN BIT(10) |
| #define MII_DP83869_MICR_FALSE_CARRIER_INT_EN BIT(8) |
| #define MII_DP83869_MICR_SLEEP_MODE_CHNG_INT_EN BIT(4) |
| #define MII_DP83869_MICR_WOL_INT_EN BIT(3) |
| #define MII_DP83869_MICR_XGMII_ERR_INT_EN BIT(2) |
| #define MII_DP83869_MICR_POL_CHNG_INT_EN BIT(1) |
| #define MII_DP83869_MICR_JABBER_INT_EN BIT(0) |
| |
| #define MII_DP83869_BMCR_DEFAULT (BMCR_ANENABLE | \ |
| BMCR_FULLDPLX | \ |
| BMCR_SPEED1000) |
| |
| /* This is the same bit mask as the BMCR so re-use the BMCR default */ |
| #define DP83869_FX_CTRL_DEFAULT MII_DP83869_BMCR_DEFAULT |
| |
| /* CFG1 bits */ |
| #define DP83869_CFG1_DEFAULT (ADVERTISE_1000HALF | \ |
| ADVERTISE_1000FULL | \ |
| CTL1000_AS_MASTER) |
| |
| /* RGMIICTL bits */ |
| #define DP83869_RGMII_TX_CLK_DELAY_EN BIT(1) |
| #define DP83869_RGMII_RX_CLK_DELAY_EN BIT(0) |
| |
| /* STRAP_STS1 bits */ |
| #define DP83869_STRAP_STS1_RESERVED BIT(11) |
| |
| /* PHYCTRL bits */ |
| #define DP83869_RX_FIFO_SHIFT 12 |
| #define DP83869_TX_FIFO_SHIFT 14 |
| |
| /* PHY_CTRL lower bytes 0x48 are declared as reserved */ |
| #define DP83869_PHY_CTRL_DEFAULT 0x48 |
| #define DP83869_PHYCR_FIFO_DEPTH_MASK GENMASK(15, 12) |
| #define DP83869_PHYCR_RESERVED_MASK BIT(11) |
| |
| /* RGMIIDCTL bits */ |
| #define DP83869_RGMII_TX_CLK_DELAY_SHIFT 4 |
| |
| /* IO_MUX_CFG bits */ |
| #define DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL 0x1f |
| |
| #define DP83869_IO_MUX_CFG_IO_IMPEDANCE_MAX 0x0 |
| #define DP83869_IO_MUX_CFG_IO_IMPEDANCE_MIN 0x1f |
| #define DP83869_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8) |
| #define DP83869_IO_MUX_CFG_CLK_O_SEL_SHIFT 8 |
| |
| /* CFG3 bits */ |
| #define DP83869_CFG3_PORT_MIRROR_EN BIT(0) |
| |
| /* CFG4 bits */ |
| #define DP83869_INT_OE BIT(7) |
| |
| /* OP MODE */ |
| #define DP83869_OP_MODE_MII BIT(5) |
| #define DP83869_SGMII_RGMII_BRIDGE BIT(6) |
| |
| enum { |
| DP83869_PORT_MIRRORING_KEEP, |
| DP83869_PORT_MIRRORING_EN, |
| DP83869_PORT_MIRRORING_DIS, |
| }; |
| |
| struct dp83869_private { |
| int tx_fifo_depth; |
| int rx_fifo_depth; |
| int io_impedance; |
| int port_mirroring; |
| bool rxctrl_strap_quirk; |
| int clk_output_sel; |
| int mode; |
| }; |
| |
| static int dp83869_ack_interrupt(struct phy_device *phydev) |
| { |
| int err = phy_read(phydev, MII_DP83869_ISR); |
| |
| if (err < 0) |
| return err; |
| |
| return 0; |
| } |
| |
| static int dp83869_config_intr(struct phy_device *phydev) |
| { |
| int micr_status = 0; |
| |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { |
| micr_status = phy_read(phydev, MII_DP83869_MICR); |
| if (micr_status < 0) |
| return micr_status; |
| |
| micr_status |= |
| (MII_DP83869_MICR_AN_ERR_INT_EN | |
| MII_DP83869_MICR_SPEED_CHNG_INT_EN | |
| MII_DP83869_MICR_AUTONEG_COMP_INT_EN | |
| MII_DP83869_MICR_LINK_STS_CHNG_INT_EN | |
| MII_DP83869_MICR_DUP_MODE_CHNG_INT_EN | |
| MII_DP83869_MICR_SLEEP_MODE_CHNG_INT_EN); |
| |
| return phy_write(phydev, MII_DP83869_MICR, micr_status); |
| } |
| |
| return phy_write(phydev, MII_DP83869_MICR, micr_status); |
| } |
| |
| static int dp83869_config_port_mirroring(struct phy_device *phydev) |
| { |
| struct dp83869_private *dp83869 = phydev->priv; |
| |
| if (dp83869->port_mirroring == DP83869_PORT_MIRRORING_EN) |
| return phy_set_bits_mmd(phydev, DP83869_DEVADDR, |
| DP83869_GEN_CFG3, |
| DP83869_CFG3_PORT_MIRROR_EN); |
| else |
| return phy_clear_bits_mmd(phydev, DP83869_DEVADDR, |
| DP83869_GEN_CFG3, |
| DP83869_CFG3_PORT_MIRROR_EN); |
| } |
| |
| #ifdef CONFIG_OF_MDIO |
| static int dp83869_of_init(struct phy_device *phydev) |
| { |
| struct dp83869_private *dp83869 = phydev->priv; |
| struct device *dev = &phydev->mdio.dev; |
| struct device_node *of_node = dev->of_node; |
| int ret; |
| |
| if (!of_node) |
| return -ENODEV; |
| |
| dp83869->io_impedance = -EINVAL; |
| |
| /* Optional configuration */ |
| ret = of_property_read_u32(of_node, "ti,clk-output-sel", |
| &dp83869->clk_output_sel); |
| if (ret || dp83869->clk_output_sel > DP83869_CLK_O_SEL_REF_CLK) |
| dp83869->clk_output_sel = DP83869_CLK_O_SEL_REF_CLK; |
| |
| ret = of_property_read_u32(of_node, "ti,op-mode", &dp83869->mode); |
| if (ret == 0) { |
| if (dp83869->mode < DP83869_RGMII_COPPER_ETHERNET || |
| dp83869->mode > DP83869_SGMII_COPPER_ETHERNET) |
| return -EINVAL; |
| } |
| |
| if (of_property_read_bool(of_node, "ti,max-output-impedance")) |
| dp83869->io_impedance = DP83869_IO_MUX_CFG_IO_IMPEDANCE_MAX; |
| else if (of_property_read_bool(of_node, "ti,min-output-impedance")) |
| dp83869->io_impedance = DP83869_IO_MUX_CFG_IO_IMPEDANCE_MIN; |
| |
| if (of_property_read_bool(of_node, "enet-phy-lane-swap")) |
| dp83869->port_mirroring = DP83869_PORT_MIRRORING_EN; |
| else |
| dp83869->port_mirroring = DP83869_PORT_MIRRORING_DIS; |
| |
| if (of_property_read_u32(of_node, "rx-fifo-depth", |
| &dp83869->rx_fifo_depth)) |
| dp83869->rx_fifo_depth = DP83869_PHYCR_FIFO_DEPTH_4_B_NIB; |
| |
| if (of_property_read_u32(of_node, "tx-fifo-depth", |
| &dp83869->tx_fifo_depth)) |
| dp83869->tx_fifo_depth = DP83869_PHYCR_FIFO_DEPTH_4_B_NIB; |
| |
| return ret; |
| } |
| #else |
| static int dp83869_of_init(struct phy_device *phydev) |
| { |
| return 0; |
| } |
| #endif /* CONFIG_OF_MDIO */ |
| |
| static int dp83869_configure_rgmii(struct phy_device *phydev, |
| struct dp83869_private *dp83869) |
| { |
| int ret = 0, val; |
| |
| if (phy_interface_is_rgmii(phydev)) { |
| val = phy_read(phydev, MII_DP83869_PHYCTRL); |
| if (val < 0) |
| return val; |
| |
| val &= ~DP83869_PHYCR_FIFO_DEPTH_MASK; |
| val |= (dp83869->tx_fifo_depth << DP83869_TX_FIFO_SHIFT); |
| val |= (dp83869->rx_fifo_depth << DP83869_RX_FIFO_SHIFT); |
| |
| ret = phy_write(phydev, MII_DP83869_PHYCTRL, val); |
| if (ret) |
| return ret; |
| } |
| |
| if (dp83869->io_impedance >= 0) |
| ret = phy_modify_mmd(phydev, DP83869_DEVADDR, |
| DP83869_IO_MUX_CFG, |
| DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL, |
| dp83869->io_impedance & |
| DP83869_IO_MUX_CFG_IO_IMPEDANCE_CTRL); |
| |
| return ret; |
| } |
| |
| static int dp83869_configure_mode(struct phy_device *phydev, |
| struct dp83869_private *dp83869) |
| { |
| int phy_ctrl_val; |
| int ret; |
| |
| if (dp83869->mode < DP83869_RGMII_COPPER_ETHERNET || |
| dp83869->mode > DP83869_SGMII_COPPER_ETHERNET) |
| return -EINVAL; |
| |
| /* Below init sequence for each operational mode is defined in |
| * section 9.4.8 of the datasheet. |
| */ |
| ret = phy_write_mmd(phydev, DP83869_DEVADDR, DP83869_OP_MODE, |
| dp83869->mode); |
| if (ret) |
| return ret; |
| |
| ret = phy_write(phydev, MII_BMCR, MII_DP83869_BMCR_DEFAULT); |
| if (ret) |
| return ret; |
| |
| phy_ctrl_val = (dp83869->rx_fifo_depth << DP83869_RX_FIFO_SHIFT | |
| dp83869->tx_fifo_depth << DP83869_TX_FIFO_SHIFT | |
| DP83869_PHY_CTRL_DEFAULT); |
| |
| switch (dp83869->mode) { |
| case DP83869_RGMII_COPPER_ETHERNET: |
| ret = phy_write(phydev, MII_DP83869_PHYCTRL, |
| phy_ctrl_val); |
| if (ret) |
| return ret; |
| |
| ret = phy_write(phydev, MII_CTRL1000, DP83869_CFG1_DEFAULT); |
| if (ret) |
| return ret; |
| |
| ret = dp83869_configure_rgmii(phydev, dp83869); |
| if (ret) |
| return ret; |
| break; |
| case DP83869_RGMII_SGMII_BRIDGE: |
| ret = phy_modify_mmd(phydev, DP83869_DEVADDR, DP83869_OP_MODE, |
| DP83869_SGMII_RGMII_BRIDGE, |
| DP83869_SGMII_RGMII_BRIDGE); |
| if (ret) |
| return ret; |
| |
| ret = phy_write_mmd(phydev, DP83869_DEVADDR, |
| DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT); |
| if (ret) |
| return ret; |
| |
| break; |
| case DP83869_1000M_MEDIA_CONVERT: |
| ret = phy_write(phydev, MII_DP83869_PHYCTRL, |
| phy_ctrl_val); |
| if (ret) |
| return ret; |
| |
| ret = phy_write_mmd(phydev, DP83869_DEVADDR, |
| DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT); |
| if (ret) |
| return ret; |
| break; |
| case DP83869_100M_MEDIA_CONVERT: |
| ret = phy_write(phydev, MII_DP83869_PHYCTRL, |
| phy_ctrl_val); |
| if (ret) |
| return ret; |
| break; |
| case DP83869_SGMII_COPPER_ETHERNET: |
| ret = phy_write(phydev, MII_DP83869_PHYCTRL, |
| phy_ctrl_val); |
| if (ret) |
| return ret; |
| |
| ret = phy_write(phydev, MII_CTRL1000, DP83869_CFG1_DEFAULT); |
| if (ret) |
| return ret; |
| |
| ret = phy_write_mmd(phydev, DP83869_DEVADDR, |
| DP83869_FX_CTRL, DP83869_FX_CTRL_DEFAULT); |
| if (ret) |
| return ret; |
| |
| break; |
| case DP83869_RGMII_1000_BASE: |
| case DP83869_RGMII_100_BASE: |
| break; |
| default: |
| return -EINVAL; |
| }; |
| |
| return ret; |
| } |
| |
| static int dp83869_config_init(struct phy_device *phydev) |
| { |
| struct dp83869_private *dp83869 = phydev->priv; |
| int ret, val; |
| |
| ret = dp83869_configure_mode(phydev, dp83869); |
| if (ret) |
| return ret; |
| |
| /* Enable Interrupt output INT_OE in CFG4 register */ |
| if (phy_interrupt_is_valid(phydev)) { |
| val = phy_read(phydev, DP83869_CFG4); |
| val |= DP83869_INT_OE; |
| phy_write(phydev, DP83869_CFG4, val); |
| } |
| |
| if (dp83869->port_mirroring != DP83869_PORT_MIRRORING_KEEP) |
| dp83869_config_port_mirroring(phydev); |
| |
| /* Clock output selection if muxing property is set */ |
| if (dp83869->clk_output_sel != DP83869_CLK_O_SEL_REF_CLK) |
| ret = phy_modify_mmd(phydev, |
| DP83869_DEVADDR, DP83869_IO_MUX_CFG, |
| DP83869_IO_MUX_CFG_CLK_O_SEL_MASK, |
| dp83869->clk_output_sel << |
| DP83869_IO_MUX_CFG_CLK_O_SEL_SHIFT); |
| |
| return ret; |
| } |
| |
| static int dp83869_probe(struct phy_device *phydev) |
| { |
| struct dp83869_private *dp83869; |
| int ret; |
| |
| dp83869 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83869), |
| GFP_KERNEL); |
| if (!dp83869) |
| return -ENOMEM; |
| |
| phydev->priv = dp83869; |
| |
| ret = dp83869_of_init(phydev); |
| if (ret) |
| return ret; |
| |
| return dp83869_config_init(phydev); |
| } |
| |
| static int dp83869_phy_reset(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = phy_write(phydev, DP83869_CTRL, DP83869_SW_RESET); |
| if (ret < 0) |
| return ret; |
| |
| usleep_range(10, 20); |
| |
| /* Global sw reset sets all registers to default. |
| * Need to set the registers in the PHY to the right config. |
| */ |
| return dp83869_config_init(phydev); |
| } |
| |
| static struct phy_driver dp83869_driver[] = { |
| { |
| PHY_ID_MATCH_MODEL(DP83869_PHY_ID), |
| .name = "TI DP83869", |
| |
| .probe = dp83869_probe, |
| .config_init = dp83869_config_init, |
| .soft_reset = dp83869_phy_reset, |
| |
| /* IRQ related */ |
| .ack_interrupt = dp83869_ack_interrupt, |
| .config_intr = dp83869_config_intr, |
| |
| .suspend = genphy_suspend, |
| .resume = genphy_resume, |
| }, |
| }; |
| module_phy_driver(dp83869_driver); |
| |
| static struct mdio_device_id __maybe_unused dp83869_tbl[] = { |
| { PHY_ID_MATCH_MODEL(DP83869_PHY_ID) }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(mdio, dp83869_tbl); |
| |
| MODULE_DESCRIPTION("Texas Instruments DP83869 PHY driver"); |
| MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com"); |
| MODULE_LICENSE("GPL v2"); |