| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright 2010 Matt Turner. | |
| * Copyright 2012 Red Hat | |
| * | |
| * Authors: Matthew Garrett | |
| * Matt Turner | |
| * Dave Airlie | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/dma-buf-map.h> | |
| #include <drm/drm_atomic_helper.h> | |
| #include <drm/drm_atomic_state_helper.h> | |
| #include <drm/drm_crtc_helper.h> | |
| #include <drm/drm_damage_helper.h> | |
| #include <drm/drm_format_helper.h> | |
| #include <drm/drm_fourcc.h> | |
| #include <drm/drm_gem_framebuffer_helper.h> | |
| #include <drm/drm_plane_helper.h> | |
| #include <drm/drm_print.h> | |
| #include <drm/drm_probe_helper.h> | |
| #include <drm/drm_simple_kms_helper.h> | |
| #include "mgag200_drv.h" | |
| #define MGAG200_LUT_SIZE 256 | |
| /* | |
| * This file contains setup code for the CRTC. | |
| */ | |
| static void mga_crtc_load_lut(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct mga_device *mdev = to_mga_device(dev); | |
| struct drm_framebuffer *fb; | |
| u16 *r_ptr, *g_ptr, *b_ptr; | |
| int i; | |
| if (!crtc->enabled) | |
| return; | |
| if (!mdev->display_pipe.plane.state) | |
| return; | |
| fb = mdev->display_pipe.plane.state->fb; | |
| r_ptr = crtc->gamma_store; | |
| g_ptr = r_ptr + crtc->gamma_size; | |
| b_ptr = g_ptr + crtc->gamma_size; | |
| WREG8(DAC_INDEX + MGA1064_INDEX, 0); | |
| if (fb && fb->format->cpp[0] * 8 == 16) { | |
| int inc = (fb->format->depth == 15) ? 8 : 4; | |
| u8 r, b; | |
| for (i = 0; i < MGAG200_LUT_SIZE; i += inc) { | |
| if (fb->format->depth == 16) { | |
| if (i > (MGAG200_LUT_SIZE >> 1)) { | |
| r = b = 0; | |
| } else { | |
| r = *r_ptr++ >> 8; | |
| b = *b_ptr++ >> 8; | |
| r_ptr++; | |
| b_ptr++; | |
| } | |
| } else { | |
| r = *r_ptr++ >> 8; | |
| b = *b_ptr++ >> 8; | |
| } | |
| /* VGA registers */ | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, r); | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, *g_ptr++ >> 8); | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, b); | |
| } | |
| return; | |
| } | |
| for (i = 0; i < MGAG200_LUT_SIZE; i++) { | |
| /* VGA registers */ | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, *r_ptr++ >> 8); | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, *g_ptr++ >> 8); | |
| WREG8(DAC_INDEX + MGA1064_COL_PAL, *b_ptr++ >> 8); | |
| } | |
| } | |
| static inline void mga_wait_vsync(struct mga_device *mdev) | |
| { | |
| unsigned long timeout = jiffies + HZ/10; | |
| unsigned int status = 0; | |
| do { | |
| status = RREG32(MGAREG_Status); | |
| } while ((status & 0x08) && time_before(jiffies, timeout)); | |
| timeout = jiffies + HZ/10; | |
| status = 0; | |
| do { | |
| status = RREG32(MGAREG_Status); | |
| } while (!(status & 0x08) && time_before(jiffies, timeout)); | |
| } | |
| static inline void mga_wait_busy(struct mga_device *mdev) | |
| { | |
| unsigned long timeout = jiffies + HZ; | |
| unsigned int status = 0; | |
| do { | |
| status = RREG8(MGAREG_Status + 2); | |
| } while ((status & 0x01) && time_before(jiffies, timeout)); | |
| } | |
| /* | |
| * PLL setup | |
| */ | |
| static int mgag200_g200_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| const int post_div_max = 7; | |
| const int in_div_min = 1; | |
| const int in_div_max = 6; | |
| const int feed_div_min = 7; | |
| const int feed_div_max = 127; | |
| u8 testm, testn; | |
| u8 n = 0, m = 0, p, s; | |
| long f_vco; | |
| long computed; | |
| long delta, tmp_delta; | |
| long ref_clk = mdev->model.g200.ref_clk; | |
| long p_clk_min = mdev->model.g200.pclk_min; | |
| long p_clk_max = mdev->model.g200.pclk_max; | |
| if (clock > p_clk_max) { | |
| drm_err(dev, "Pixel Clock %ld too high\n", clock); | |
| return 1; | |
| } | |
| if (clock < p_clk_min >> 3) | |
| clock = p_clk_min >> 3; | |
| f_vco = clock; | |
| for (p = 0; | |
| p <= post_div_max && f_vco < p_clk_min; | |
| p = (p << 1) + 1, f_vco <<= 1) | |
| ; | |
| delta = clock; | |
| for (testm = in_div_min; testm <= in_div_max; testm++) { | |
| for (testn = feed_div_min; testn <= feed_div_max; testn++) { | |
| computed = ref_clk * (testn + 1) / (testm + 1); | |
| if (computed < f_vco) | |
| tmp_delta = f_vco - computed; | |
| else | |
| tmp_delta = computed - f_vco; | |
| if (tmp_delta < delta) { | |
| delta = tmp_delta; | |
| m = testm; | |
| n = testn; | |
| } | |
| } | |
| } | |
| f_vco = ref_clk * (n + 1) / (m + 1); | |
| if (f_vco < 100000) | |
| s = 0; | |
| else if (f_vco < 140000) | |
| s = 1; | |
| else if (f_vco < 180000) | |
| s = 2; | |
| else | |
| s = 3; | |
| drm_dbg_kms(dev, "clock: %ld vco: %ld m: %d n: %d p: %d s: %d\n", | |
| clock, f_vco, m, n, p, s); | |
| WREG_DAC(MGA1064_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_PIX_PLLC_P, (p | (s << 3))); | |
| return 0; | |
| } | |
| #define P_ARRAY_SIZE 9 | |
| static int mga_g200se_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| u32 unique_rev_id = mdev->model.g200se.unique_rev_id; | |
| unsigned int vcomax, vcomin, pllreffreq; | |
| unsigned int delta, tmpdelta, permitteddelta; | |
| unsigned int testp, testm, testn; | |
| unsigned int p, m, n; | |
| unsigned int computed; | |
| unsigned int pvalues_e4[P_ARRAY_SIZE] = {16, 14, 12, 10, 8, 6, 4, 2, 1}; | |
| unsigned int fvv; | |
| unsigned int i; | |
| if (unique_rev_id <= 0x03) { | |
| m = n = p = 0; | |
| vcomax = 320000; | |
| vcomin = 160000; | |
| pllreffreq = 25000; | |
| delta = 0xffffffff; | |
| permitteddelta = clock * 5 / 1000; | |
| for (testp = 8; testp > 0; testp /= 2) { | |
| if (clock * testp > vcomax) | |
| continue; | |
| if (clock * testp < vcomin) | |
| continue; | |
| for (testn = 17; testn < 256; testn++) { | |
| for (testm = 1; testm < 32; testm++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| m = testm - 1; | |
| n = testn - 1; | |
| p = testp - 1; | |
| } | |
| } | |
| } | |
| } | |
| } else { | |
| m = n = p = 0; | |
| vcomax = 1600000; | |
| vcomin = 800000; | |
| pllreffreq = 25000; | |
| if (clock < 25000) | |
| clock = 25000; | |
| clock = clock * 2; | |
| delta = 0xFFFFFFFF; | |
| /* Permited delta is 0.5% as VESA Specification */ | |
| permitteddelta = clock * 5 / 1000; | |
| for (i = 0 ; i < P_ARRAY_SIZE ; i++) { | |
| testp = pvalues_e4[i]; | |
| if ((clock * testp) > vcomax) | |
| continue; | |
| if ((clock * testp) < vcomin) | |
| continue; | |
| for (testn = 50; testn <= 256; testn++) { | |
| for (testm = 1; testm <= 32; testm++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| m = testm - 1; | |
| n = testn - 1; | |
| p = testp - 1; | |
| } | |
| } | |
| } | |
| } | |
| fvv = pllreffreq * (n + 1) / (m + 1); | |
| fvv = (fvv - 800000) / 50000; | |
| if (fvv > 15) | |
| fvv = 15; | |
| p |= (fvv << 4); | |
| m |= 0x80; | |
| clock = clock / 2; | |
| } | |
| if (delta > permitteddelta) { | |
| pr_warn("PLL delta too large\n"); | |
| return 1; | |
| } | |
| WREG_DAC(MGA1064_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_PIX_PLLC_P, p); | |
| if (unique_rev_id >= 0x04) { | |
| WREG_DAC(0x1a, 0x09); | |
| msleep(20); | |
| WREG_DAC(0x1a, 0x01); | |
| } | |
| return 0; | |
| } | |
| static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| unsigned int vcomax, vcomin, pllreffreq; | |
| unsigned int delta, tmpdelta; | |
| unsigned int testp, testm, testn, testp2; | |
| unsigned int p, m, n; | |
| unsigned int computed; | |
| int i, j, tmpcount, vcount; | |
| bool pll_locked = false; | |
| u8 tmp; | |
| m = n = p = 0; | |
| delta = 0xffffffff; | |
| if (mdev->type == G200_EW3) { | |
| vcomax = 800000; | |
| vcomin = 400000; | |
| pllreffreq = 25000; | |
| for (testp = 1; testp < 8; testp++) { | |
| for (testp2 = 1; testp2 < 8; testp2++) { | |
| if (testp < testp2) | |
| continue; | |
| if ((clock * testp * testp2) > vcomax) | |
| continue; | |
| if ((clock * testp * testp2) < vcomin) | |
| continue; | |
| for (testm = 1; testm < 26; testm++) { | |
| for (testn = 32; testn < 2048 ; testn++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp * testp2); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| m = ((testn & 0x100) >> 1) | | |
| (testm); | |
| n = (testn & 0xFF); | |
| p = ((testn & 0x600) >> 3) | | |
| (testp2 << 3) | | |
| (testp); | |
| } | |
| } | |
| } | |
| } | |
| } | |
| } else { | |
| vcomax = 550000; | |
| vcomin = 150000; | |
| pllreffreq = 48000; | |
| for (testp = 1; testp < 9; testp++) { | |
| if (clock * testp > vcomax) | |
| continue; | |
| if (clock * testp < vcomin) | |
| continue; | |
| for (testm = 1; testm < 17; testm++) { | |
| for (testn = 1; testn < 151; testn++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| n = testn - 1; | |
| m = (testm - 1) | | |
| ((n >> 1) & 0x80); | |
| p = testp - 1; | |
| } | |
| } | |
| } | |
| } | |
| } | |
| for (i = 0; i <= 32 && pll_locked == false; i++) { | |
| if (i > 0) { | |
| WREG8(MGAREG_CRTC_INDEX, 0x1e); | |
| tmp = RREG8(MGAREG_CRTC_DATA); | |
| if (tmp < 0xff) | |
| WREG8(MGAREG_CRTC_DATA, tmp+1); | |
| } | |
| /* set pixclkdis to 1 */ | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_REMHEADCTL_CLKDIS; | |
| WREG8(DAC_DATA, tmp); | |
| /* select PLL Set C */ | |
| tmp = RREG8(MGAREG_MEM_MISC_READ); | |
| tmp |= 0x3 << 2; | |
| WREG8(MGAREG_MEM_MISC_WRITE, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN | 0x80; | |
| WREG8(DAC_DATA, tmp); | |
| udelay(500); | |
| /* reset the PLL */ | |
| WREG8(DAC_INDEX, MGA1064_VREF_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~0x04; | |
| WREG8(DAC_DATA, tmp); | |
| udelay(50); | |
| /* program pixel pll register */ | |
| WREG_DAC(MGA1064_WB_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_WB_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_WB_PIX_PLLC_P, p); | |
| udelay(50); | |
| /* turn pll on */ | |
| WREG8(DAC_INDEX, MGA1064_VREF_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= 0x04; | |
| WREG_DAC(MGA1064_VREF_CTL, tmp); | |
| udelay(500); | |
| /* select the pixel pll */ | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; | |
| tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; | |
| WREG8(DAC_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_REMHEADCTL_CLKSL_MSK; | |
| tmp |= MGA1064_REMHEADCTL_CLKSL_PLL; | |
| WREG8(DAC_DATA, tmp); | |
| /* reset dotclock rate bit */ | |
| WREG8(MGAREG_SEQ_INDEX, 1); | |
| tmp = RREG8(MGAREG_SEQ_DATA); | |
| tmp &= ~0x8; | |
| WREG8(MGAREG_SEQ_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| vcount = RREG8(MGAREG_VCOUNT); | |
| for (j = 0; j < 30 && pll_locked == false; j++) { | |
| tmpcount = RREG8(MGAREG_VCOUNT); | |
| if (tmpcount < vcount) | |
| vcount = 0; | |
| if ((tmpcount - vcount) > 2) | |
| pll_locked = true; | |
| else | |
| udelay(5); | |
| } | |
| } | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_REMHEADCTL_CLKDIS; | |
| WREG_DAC(MGA1064_REMHEADCTL, tmp); | |
| return 0; | |
| } | |
| static int mga_g200ev_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| unsigned int vcomax, vcomin, pllreffreq; | |
| unsigned int delta, tmpdelta; | |
| unsigned int testp, testm, testn; | |
| unsigned int p, m, n; | |
| unsigned int computed; | |
| u8 tmp; | |
| m = n = p = 0; | |
| vcomax = 550000; | |
| vcomin = 150000; | |
| pllreffreq = 50000; | |
| delta = 0xffffffff; | |
| for (testp = 16; testp > 0; testp--) { | |
| if (clock * testp > vcomax) | |
| continue; | |
| if (clock * testp < vcomin) | |
| continue; | |
| for (testn = 1; testn < 257; testn++) { | |
| for (testm = 1; testm < 17; testm++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| n = testn - 1; | |
| m = testm - 1; | |
| p = testp - 1; | |
| } | |
| } | |
| } | |
| } | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| tmp = RREG8(MGAREG_MEM_MISC_READ); | |
| tmp |= 0x3 << 2; | |
| WREG8(MGAREG_MEM_MISC_WRITE, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_PLL_STAT); | |
| tmp = RREG8(DAC_DATA); | |
| WREG8(DAC_DATA, tmp & ~0x40); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; | |
| WREG8(DAC_DATA, tmp); | |
| WREG_DAC(MGA1064_EV_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_EV_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_EV_PIX_PLLC_P, p); | |
| udelay(50); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; | |
| WREG8(DAC_DATA, tmp); | |
| udelay(500); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; | |
| tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; | |
| WREG8(DAC_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_PLL_STAT); | |
| tmp = RREG8(DAC_DATA); | |
| WREG8(DAC_DATA, tmp | 0x40); | |
| tmp = RREG8(MGAREG_MEM_MISC_READ); | |
| tmp |= (0x3 << 2); | |
| WREG8(MGAREG_MEM_MISC_WRITE, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| return 0; | |
| } | |
| static int mga_g200eh_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| unsigned int vcomax, vcomin, pllreffreq; | |
| unsigned int delta, tmpdelta; | |
| unsigned int testp, testm, testn; | |
| unsigned int p, m, n; | |
| unsigned int computed; | |
| int i, j, tmpcount, vcount; | |
| u8 tmp; | |
| bool pll_locked = false; | |
| m = n = p = 0; | |
| if (mdev->type == G200_EH3) { | |
| vcomax = 3000000; | |
| vcomin = 1500000; | |
| pllreffreq = 25000; | |
| delta = 0xffffffff; | |
| testp = 0; | |
| for (testm = 150; testm >= 6; testm--) { | |
| if (clock * testm > vcomax) | |
| continue; | |
| if (clock * testm < vcomin) | |
| continue; | |
| for (testn = 120; testn >= 60; testn--) { | |
| computed = (pllreffreq * testn) / testm; | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| n = testn; | |
| m = testm; | |
| p = testp; | |
| } | |
| if (delta == 0) | |
| break; | |
| } | |
| if (delta == 0) | |
| break; | |
| } | |
| } else { | |
| vcomax = 800000; | |
| vcomin = 400000; | |
| pllreffreq = 33333; | |
| delta = 0xffffffff; | |
| for (testp = 16; testp > 0; testp >>= 1) { | |
| if (clock * testp > vcomax) | |
| continue; | |
| if (clock * testp < vcomin) | |
| continue; | |
| for (testm = 1; testm < 33; testm++) { | |
| for (testn = 17; testn < 257; testn++) { | |
| computed = (pllreffreq * testn) / | |
| (testm * testp); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| n = testn - 1; | |
| m = (testm - 1); | |
| p = testp - 1; | |
| } | |
| if ((clock * testp) >= 600000) | |
| p |= 0x80; | |
| } | |
| } | |
| } | |
| } | |
| for (i = 0; i <= 32 && pll_locked == false; i++) { | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| tmp = RREG8(MGAREG_MEM_MISC_READ); | |
| tmp |= 0x3 << 2; | |
| WREG8(MGAREG_MEM_MISC_WRITE, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; | |
| WREG8(DAC_DATA, tmp); | |
| udelay(500); | |
| WREG_DAC(MGA1064_EH_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_EH_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_EH_PIX_PLLC_P, p); | |
| udelay(500); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; | |
| tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; | |
| WREG8(DAC_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; | |
| WREG8(DAC_DATA, tmp); | |
| vcount = RREG8(MGAREG_VCOUNT); | |
| for (j = 0; j < 30 && pll_locked == false; j++) { | |
| tmpcount = RREG8(MGAREG_VCOUNT); | |
| if (tmpcount < vcount) | |
| vcount = 0; | |
| if ((tmpcount - vcount) > 2) | |
| pll_locked = true; | |
| else | |
| udelay(5); | |
| } | |
| } | |
| return 0; | |
| } | |
| static int mga_g200er_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| unsigned int vcomax, vcomin, pllreffreq; | |
| unsigned int delta, tmpdelta; | |
| int testr, testn, testm, testo; | |
| unsigned int p, m, n; | |
| unsigned int computed, vco; | |
| int tmp; | |
| const unsigned int m_div_val[] = { 1, 2, 4, 8 }; | |
| m = n = p = 0; | |
| vcomax = 1488000; | |
| vcomin = 1056000; | |
| pllreffreq = 48000; | |
| delta = 0xffffffff; | |
| for (testr = 0; testr < 4; testr++) { | |
| if (delta == 0) | |
| break; | |
| for (testn = 5; testn < 129; testn++) { | |
| if (delta == 0) | |
| break; | |
| for (testm = 3; testm >= 0; testm--) { | |
| if (delta == 0) | |
| break; | |
| for (testo = 5; testo < 33; testo++) { | |
| vco = pllreffreq * (testn + 1) / | |
| (testr + 1); | |
| if (vco < vcomin) | |
| continue; | |
| if (vco > vcomax) | |
| continue; | |
| computed = vco / (m_div_val[testm] * (testo + 1)); | |
| if (computed > clock) | |
| tmpdelta = computed - clock; | |
| else | |
| tmpdelta = clock - computed; | |
| if (tmpdelta < delta) { | |
| delta = tmpdelta; | |
| m = testm | (testo << 3); | |
| n = testn; | |
| p = testr | (testr << 3); | |
| } | |
| } | |
| } | |
| } | |
| } | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| WREG8(DAC_DATA, tmp); | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= MGA1064_REMHEADCTL_CLKDIS; | |
| WREG8(DAC_DATA, tmp); | |
| tmp = RREG8(MGAREG_MEM_MISC_READ); | |
| tmp |= (0x3<<2) | 0xc0; | |
| WREG8(MGAREG_MEM_MISC_WRITE, tmp); | |
| WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; | |
| tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; | |
| WREG8(DAC_DATA, tmp); | |
| udelay(500); | |
| WREG_DAC(MGA1064_ER_PIX_PLLC_N, n); | |
| WREG_DAC(MGA1064_ER_PIX_PLLC_M, m); | |
| WREG_DAC(MGA1064_ER_PIX_PLLC_P, p); | |
| udelay(50); | |
| return 0; | |
| } | |
| static int mgag200_crtc_set_plls(struct mga_device *mdev, long clock) | |
| { | |
| u8 misc; | |
| switch(mdev->type) { | |
| case G200_PCI: | |
| case G200_AGP: | |
| return mgag200_g200_set_plls(mdev, clock); | |
| case G200_SE_A: | |
| case G200_SE_B: | |
| return mga_g200se_set_plls(mdev, clock); | |
| case G200_WB: | |
| case G200_EW3: | |
| return mga_g200wb_set_plls(mdev, clock); | |
| case G200_EV: | |
| return mga_g200ev_set_plls(mdev, clock); | |
| case G200_EH: | |
| case G200_EH3: | |
| return mga_g200eh_set_plls(mdev, clock); | |
| case G200_ER: | |
| return mga_g200er_set_plls(mdev, clock); | |
| } | |
| misc = RREG8(MGA_MISC_IN); | |
| misc &= ~MGAREG_MISC_CLK_SEL_MASK; | |
| misc |= MGAREG_MISC_CLK_SEL_MGA_MSK; | |
| WREG8(MGA_MISC_OUT, misc); | |
| return 0; | |
| } | |
| static void mgag200_g200wb_hold_bmc(struct mga_device *mdev) | |
| { | |
| u8 tmp; | |
| int iter_max; | |
| /* 1- The first step is to warn the BMC of an upcoming mode change. | |
| * We are putting the misc<0> to output.*/ | |
| WREG8(DAC_INDEX, MGA1064_GEN_IO_CTL); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= 0x10; | |
| WREG_DAC(MGA1064_GEN_IO_CTL, tmp); | |
| /* we are putting a 1 on the misc<0> line */ | |
| WREG8(DAC_INDEX, MGA1064_GEN_IO_DATA); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= 0x10; | |
| WREG_DAC(MGA1064_GEN_IO_DATA, tmp); | |
| /* 2- Second step to mask and further scan request | |
| * This will be done by asserting the remfreqmsk bit (XSPAREREG<7>) | |
| */ | |
| WREG8(DAC_INDEX, MGA1064_SPAREREG); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= 0x80; | |
| WREG_DAC(MGA1064_SPAREREG, tmp); | |
| /* 3a- the third step is to verifu if there is an active scan | |
| * We are searching for a 0 on remhsyncsts <XSPAREREG<0>) | |
| */ | |
| iter_max = 300; | |
| while (!(tmp & 0x1) && iter_max) { | |
| WREG8(DAC_INDEX, MGA1064_SPAREREG); | |
| tmp = RREG8(DAC_DATA); | |
| udelay(1000); | |
| iter_max--; | |
| } | |
| /* 3b- this step occurs only if the remove is actually scanning | |
| * we are waiting for the end of the frame which is a 1 on | |
| * remvsyncsts (XSPAREREG<1>) | |
| */ | |
| if (iter_max) { | |
| iter_max = 300; | |
| while ((tmp & 0x2) && iter_max) { | |
| WREG8(DAC_INDEX, MGA1064_SPAREREG); | |
| tmp = RREG8(DAC_DATA); | |
| udelay(1000); | |
| iter_max--; | |
| } | |
| } | |
| } | |
| static void mgag200_g200wb_release_bmc(struct mga_device *mdev) | |
| { | |
| u8 tmp; | |
| /* 1- The first step is to ensure that the vrsten and hrsten are set */ | |
| WREG8(MGAREG_CRTCEXT_INDEX, 1); | |
| tmp = RREG8(MGAREG_CRTCEXT_DATA); | |
| WREG8(MGAREG_CRTCEXT_DATA, tmp | 0x88); | |
| /* 2- second step is to assert the rstlvl2 */ | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL2); | |
| tmp = RREG8(DAC_DATA); | |
| tmp |= 0x8; | |
| WREG8(DAC_DATA, tmp); | |
| /* wait 10 us */ | |
| udelay(10); | |
| /* 3- deassert rstlvl2 */ | |
| tmp &= ~0x08; | |
| WREG8(DAC_INDEX, MGA1064_REMHEADCTL2); | |
| WREG8(DAC_DATA, tmp); | |
| /* 4- remove mask of scan request */ | |
| WREG8(DAC_INDEX, MGA1064_SPAREREG); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~0x80; | |
| WREG8(DAC_DATA, tmp); | |
| /* 5- put back a 0 on the misc<0> line */ | |
| WREG8(DAC_INDEX, MGA1064_GEN_IO_DATA); | |
| tmp = RREG8(DAC_DATA); | |
| tmp &= ~0x10; | |
| WREG_DAC(MGA1064_GEN_IO_DATA, tmp); | |
| } | |
| /* | |
| * This is how the framebuffer base address is stored in g200 cards: | |
| * * Assume @offset is the gpu_addr variable of the framebuffer object | |
| * * Then addr is the number of _pixels_ (not bytes) from the start of | |
| * VRAM to the first pixel we want to display. (divided by 2 for 32bit | |
| * framebuffers) | |
| * * addr is stored in the CRTCEXT0, CRTCC and CRTCD registers | |
| * addr<20> -> CRTCEXT0<6> | |
| * addr<19-16> -> CRTCEXT0<3-0> | |
| * addr<15-8> -> CRTCC<7-0> | |
| * addr<7-0> -> CRTCD<7-0> | |
| * | |
| * CRTCEXT0 has to be programmed last to trigger an update and make the | |
| * new addr variable take effect. | |
| */ | |
| static void mgag200_set_startadd(struct mga_device *mdev, | |
| unsigned long offset) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| u32 startadd; | |
| u8 crtcc, crtcd, crtcext0; | |
| startadd = offset / 8; | |
| /* | |
| * Can't store addresses any higher than that, but we also | |
| * don't have more than 16 MiB of memory, so it should be fine. | |
| */ | |
| drm_WARN_ON(dev, startadd > 0x1fffff); | |
| RREG_ECRT(0x00, crtcext0); | |
| crtcc = (startadd >> 8) & 0xff; | |
| crtcd = startadd & 0xff; | |
| crtcext0 &= 0xb0; | |
| crtcext0 |= ((startadd >> 14) & BIT(6)) | | |
| ((startadd >> 16) & 0x0f); | |
| WREG_CRT(0x0c, crtcc); | |
| WREG_CRT(0x0d, crtcd); | |
| WREG_ECRT(0x00, crtcext0); | |
| } | |
| static void mgag200_set_dac_regs(struct mga_device *mdev) | |
| { | |
| size_t i; | |
| u8 dacvalue[] = { | |
| /* 0x00: */ 0, 0, 0, 0, 0, 0, 0x00, 0, | |
| /* 0x08: */ 0, 0, 0, 0, 0, 0, 0, 0, | |
| /* 0x10: */ 0, 0, 0, 0, 0, 0, 0, 0, | |
| /* 0x18: */ 0x00, 0, 0xC9, 0xFF, 0xBF, 0x20, 0x1F, 0x20, | |
| /* 0x20: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| /* 0x28: */ 0x00, 0x00, 0x00, 0x00, 0, 0, 0, 0x40, | |
| /* 0x30: */ 0x00, 0xB0, 0x00, 0xC2, 0x34, 0x14, 0x02, 0x83, | |
| /* 0x38: */ 0x00, 0x93, 0x00, 0x77, 0x00, 0x00, 0x00, 0x3A, | |
| /* 0x40: */ 0, 0, 0, 0, 0, 0, 0, 0, | |
| /* 0x48: */ 0, 0, 0, 0, 0, 0, 0, 0 | |
| }; | |
| switch (mdev->type) { | |
| case G200_PCI: | |
| case G200_AGP: | |
| dacvalue[MGA1064_SYS_PLL_M] = 0x04; | |
| dacvalue[MGA1064_SYS_PLL_N] = 0x2D; | |
| dacvalue[MGA1064_SYS_PLL_P] = 0x19; | |
| break; | |
| case G200_SE_A: | |
| case G200_SE_B: | |
| dacvalue[MGA1064_VREF_CTL] = 0x03; | |
| dacvalue[MGA1064_PIX_CLK_CTL] = MGA1064_PIX_CLK_CTL_SEL_PLL; | |
| dacvalue[MGA1064_MISC_CTL] = MGA1064_MISC_CTL_DAC_EN | | |
| MGA1064_MISC_CTL_VGA8 | | |
| MGA1064_MISC_CTL_DAC_RAM_CS; | |
| break; | |
| case G200_WB: | |
| case G200_EW3: | |
| dacvalue[MGA1064_VREF_CTL] = 0x07; | |
| break; | |
| case G200_EV: | |
| dacvalue[MGA1064_PIX_CLK_CTL] = MGA1064_PIX_CLK_CTL_SEL_PLL; | |
| dacvalue[MGA1064_MISC_CTL] = MGA1064_MISC_CTL_VGA8 | | |
| MGA1064_MISC_CTL_DAC_RAM_CS; | |
| break; | |
| case G200_EH: | |
| case G200_EH3: | |
| dacvalue[MGA1064_MISC_CTL] = MGA1064_MISC_CTL_VGA8 | | |
| MGA1064_MISC_CTL_DAC_RAM_CS; | |
| break; | |
| case G200_ER: | |
| break; | |
| } | |
| for (i = 0; i < ARRAY_SIZE(dacvalue); i++) { | |
| if ((i <= 0x17) || | |
| (i == 0x1b) || | |
| (i == 0x1c) || | |
| ((i >= 0x1f) && (i <= 0x29)) || | |
| ((i >= 0x30) && (i <= 0x37))) | |
| continue; | |
| if (IS_G200_SE(mdev) && | |
| ((i == 0x2c) || (i == 0x2d) || (i == 0x2e))) | |
| continue; | |
| if ((mdev->type == G200_EV || | |
| mdev->type == G200_WB || | |
| mdev->type == G200_EH || | |
| mdev->type == G200_EW3 || | |
| mdev->type == G200_EH3) && | |
| (i >= 0x44) && (i <= 0x4e)) | |
| continue; | |
| WREG_DAC(i, dacvalue[i]); | |
| } | |
| if (mdev->type == G200_ER) | |
| WREG_DAC(0x90, 0); | |
| } | |
| static void mgag200_init_regs(struct mga_device *mdev) | |
| { | |
| u8 crtc11, misc; | |
| mgag200_set_dac_regs(mdev); | |
| WREG_SEQ(2, 0x0f); | |
| WREG_SEQ(3, 0x00); | |
| WREG_SEQ(4, 0x0e); | |
| WREG_CRT(10, 0); | |
| WREG_CRT(11, 0); | |
| WREG_CRT(12, 0); | |
| WREG_CRT(13, 0); | |
| WREG_CRT(14, 0); | |
| WREG_CRT(15, 0); | |
| RREG_CRT(0x11, crtc11); | |
| crtc11 &= ~(MGAREG_CRTC11_CRTCPROTECT | | |
| MGAREG_CRTC11_VINTEN | | |
| MGAREG_CRTC11_VINTCLR); | |
| WREG_CRT(0x11, crtc11); | |
| if (mdev->type == G200_ER) | |
| WREG_ECRT(0x24, 0x5); | |
| if (mdev->type == G200_EW3) | |
| WREG_ECRT(0x34, 0x5); | |
| misc = RREG8(MGA_MISC_IN); | |
| misc |= MGAREG_MISC_IOADSEL; | |
| WREG8(MGA_MISC_OUT, misc); | |
| } | |
| static void mgag200_set_mode_regs(struct mga_device *mdev, | |
| const struct drm_display_mode *mode) | |
| { | |
| unsigned int hdisplay, hsyncstart, hsyncend, htotal; | |
| unsigned int vdisplay, vsyncstart, vsyncend, vtotal; | |
| u8 misc, crtcext1, crtcext2, crtcext5; | |
| hdisplay = mode->hdisplay / 8 - 1; | |
| hsyncstart = mode->hsync_start / 8 - 1; | |
| hsyncend = mode->hsync_end / 8 - 1; | |
| htotal = mode->htotal / 8 - 1; | |
| /* Work around hardware quirk */ | |
| if ((htotal & 0x07) == 0x06 || (htotal & 0x07) == 0x04) | |
| htotal++; | |
| vdisplay = mode->vdisplay - 1; | |
| vsyncstart = mode->vsync_start - 1; | |
| vsyncend = mode->vsync_end - 1; | |
| vtotal = mode->vtotal - 2; | |
| misc = RREG8(MGA_MISC_IN); | |
| if (mode->flags & DRM_MODE_FLAG_NHSYNC) | |
| misc |= MGAREG_MISC_HSYNCPOL; | |
| else | |
| misc &= ~MGAREG_MISC_HSYNCPOL; | |
| if (mode->flags & DRM_MODE_FLAG_NVSYNC) | |
| misc |= MGAREG_MISC_VSYNCPOL; | |
| else | |
| misc &= ~MGAREG_MISC_VSYNCPOL; | |
| crtcext1 = (((htotal - 4) & 0x100) >> 8) | | |
| ((hdisplay & 0x100) >> 7) | | |
| ((hsyncstart & 0x100) >> 6) | | |
| (htotal & 0x40); | |
| if (mdev->type == G200_WB || mdev->type == G200_EW3) | |
| crtcext1 |= BIT(7) | /* vrsten */ | |
| BIT(3); /* hrsten */ | |
| crtcext2 = ((vtotal & 0xc00) >> 10) | | |
| ((vdisplay & 0x400) >> 8) | | |
| ((vdisplay & 0xc00) >> 7) | | |
| ((vsyncstart & 0xc00) >> 5) | | |
| ((vdisplay & 0x400) >> 3); | |
| crtcext5 = 0x00; | |
| WREG_CRT(0, htotal - 4); | |
| WREG_CRT(1, hdisplay); | |
| WREG_CRT(2, hdisplay); | |
| WREG_CRT(3, (htotal & 0x1F) | 0x80); | |
| WREG_CRT(4, hsyncstart); | |
| WREG_CRT(5, ((htotal & 0x20) << 2) | (hsyncend & 0x1F)); | |
| WREG_CRT(6, vtotal & 0xFF); | |
| WREG_CRT(7, ((vtotal & 0x100) >> 8) | | |
| ((vdisplay & 0x100) >> 7) | | |
| ((vsyncstart & 0x100) >> 6) | | |
| ((vdisplay & 0x100) >> 5) | | |
| ((vdisplay & 0x100) >> 4) | /* linecomp */ | |
| ((vtotal & 0x200) >> 4) | | |
| ((vdisplay & 0x200) >> 3) | | |
| ((vsyncstart & 0x200) >> 2)); | |
| WREG_CRT(9, ((vdisplay & 0x200) >> 4) | | |
| ((vdisplay & 0x200) >> 3)); | |
| WREG_CRT(16, vsyncstart & 0xFF); | |
| WREG_CRT(17, (vsyncend & 0x0F) | 0x20); | |
| WREG_CRT(18, vdisplay & 0xFF); | |
| WREG_CRT(20, 0); | |
| WREG_CRT(21, vdisplay & 0xFF); | |
| WREG_CRT(22, (vtotal + 1) & 0xFF); | |
| WREG_CRT(23, 0xc3); | |
| WREG_CRT(24, vdisplay & 0xFF); | |
| WREG_ECRT(0x01, crtcext1); | |
| WREG_ECRT(0x02, crtcext2); | |
| WREG_ECRT(0x05, crtcext5); | |
| WREG8(MGA_MISC_OUT, misc); | |
| } | |
| static u8 mgag200_get_bpp_shift(struct mga_device *mdev, | |
| const struct drm_format_info *format) | |
| { | |
| return mdev->bpp_shifts[format->cpp[0] - 1]; | |
| } | |
| /* | |
| * Calculates the HW offset value from the framebuffer's pitch. The | |
| * offset is a multiple of the pixel size and depends on the display | |
| * format. | |
| */ | |
| static u32 mgag200_calculate_offset(struct mga_device *mdev, | |
| const struct drm_framebuffer *fb) | |
| { | |
| u32 offset = fb->pitches[0] / fb->format->cpp[0]; | |
| u8 bppshift = mgag200_get_bpp_shift(mdev, fb->format); | |
| if (fb->format->cpp[0] * 8 == 24) | |
| offset = (offset * 3) >> (4 - bppshift); | |
| else | |
| offset = offset >> (4 - bppshift); | |
| return offset; | |
| } | |
| static void mgag200_set_offset(struct mga_device *mdev, | |
| const struct drm_framebuffer *fb) | |
| { | |
| u8 crtc13, crtcext0; | |
| u32 offset = mgag200_calculate_offset(mdev, fb); | |
| RREG_ECRT(0, crtcext0); | |
| crtc13 = offset & 0xff; | |
| crtcext0 &= ~MGAREG_CRTCEXT0_OFFSET_MASK; | |
| crtcext0 |= (offset >> 4) & MGAREG_CRTCEXT0_OFFSET_MASK; | |
| WREG_CRT(0x13, crtc13); | |
| WREG_ECRT(0x00, crtcext0); | |
| } | |
| static void mgag200_set_format_regs(struct mga_device *mdev, | |
| const struct drm_framebuffer *fb) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| const struct drm_format_info *format = fb->format; | |
| unsigned int bpp, bppshift, scale; | |
| u8 crtcext3, xmulctrl; | |
| bpp = format->cpp[0] * 8; | |
| bppshift = mgag200_get_bpp_shift(mdev, format); | |
| switch (bpp) { | |
| case 24: | |
| scale = ((1 << bppshift) * 3) - 1; | |
| break; | |
| default: | |
| scale = (1 << bppshift) - 1; | |
| break; | |
| } | |
| RREG_ECRT(3, crtcext3); | |
| switch (bpp) { | |
| case 8: | |
| xmulctrl = MGA1064_MUL_CTL_8bits; | |
| break; | |
| case 16: | |
| if (format->depth == 15) | |
| xmulctrl = MGA1064_MUL_CTL_15bits; | |
| else | |
| xmulctrl = MGA1064_MUL_CTL_16bits; | |
| break; | |
| case 24: | |
| xmulctrl = MGA1064_MUL_CTL_24bits; | |
| break; | |
| case 32: | |
| xmulctrl = MGA1064_MUL_CTL_32_24bits; | |
| break; | |
| default: | |
| /* BUG: We should have caught this problem already. */ | |
| drm_WARN_ON(dev, "invalid format depth\n"); | |
| return; | |
| } | |
| crtcext3 &= ~GENMASK(2, 0); | |
| crtcext3 |= scale; | |
| WREG_DAC(MGA1064_MUL_CTL, xmulctrl); | |
| WREG_GFX(0, 0x00); | |
| WREG_GFX(1, 0x00); | |
| WREG_GFX(2, 0x00); | |
| WREG_GFX(3, 0x00); | |
| WREG_GFX(4, 0x00); | |
| WREG_GFX(5, 0x40); | |
| WREG_GFX(6, 0x05); | |
| WREG_GFX(7, 0x0f); | |
| WREG_GFX(8, 0x0f); | |
| WREG_ECRT(3, crtcext3); | |
| } | |
| static void mgag200_g200er_reset_tagfifo(struct mga_device *mdev) | |
| { | |
| static uint32_t RESET_FLAG = 0x00200000; /* undocumented magic value */ | |
| u32 memctl; | |
| memctl = RREG32(MGAREG_MEMCTL); | |
| memctl |= RESET_FLAG; | |
| WREG32(MGAREG_MEMCTL, memctl); | |
| udelay(1000); | |
| memctl &= ~RESET_FLAG; | |
| WREG32(MGAREG_MEMCTL, memctl); | |
| } | |
| static void mgag200_g200se_set_hiprilvl(struct mga_device *mdev, | |
| const struct drm_display_mode *mode, | |
| const struct drm_framebuffer *fb) | |
| { | |
| u32 unique_rev_id = mdev->model.g200se.unique_rev_id; | |
| unsigned int hiprilvl; | |
| u8 crtcext6; | |
| if (unique_rev_id >= 0x04) { | |
| hiprilvl = 0; | |
| } else if (unique_rev_id >= 0x02) { | |
| unsigned int bpp; | |
| unsigned long mb; | |
| if (fb->format->cpp[0] * 8 > 16) | |
| bpp = 32; | |
| else if (fb->format->cpp[0] * 8 > 8) | |
| bpp = 16; | |
| else | |
| bpp = 8; | |
| mb = (mode->clock * bpp) / 1000; | |
| if (mb > 3100) | |
| hiprilvl = 0; | |
| else if (mb > 2600) | |
| hiprilvl = 1; | |
| else if (mb > 1900) | |
| hiprilvl = 2; | |
| else if (mb > 1160) | |
| hiprilvl = 3; | |
| else if (mb > 440) | |
| hiprilvl = 4; | |
| else | |
| hiprilvl = 5; | |
| } else if (unique_rev_id >= 0x01) { | |
| hiprilvl = 3; | |
| } else { | |
| hiprilvl = 4; | |
| } | |
| crtcext6 = hiprilvl; /* implicitly sets maxhipri to 0 */ | |
| WREG_ECRT(0x06, crtcext6); | |
| } | |
| static void mgag200_g200ev_set_hiprilvl(struct mga_device *mdev) | |
| { | |
| WREG_ECRT(0x06, 0x00); | |
| } | |
| static void mgag200_enable_display(struct mga_device *mdev) | |
| { | |
| u8 seq0, seq1, crtcext1; | |
| RREG_SEQ(0x00, seq0); | |
| seq0 |= MGAREG_SEQ0_SYNCRST | | |
| MGAREG_SEQ0_ASYNCRST; | |
| WREG_SEQ(0x00, seq0); | |
| /* | |
| * TODO: replace busy waiting with vblank IRQ; put | |
| * msleep(50) before changing SCROFF | |
| */ | |
| mga_wait_vsync(mdev); | |
| mga_wait_busy(mdev); | |
| RREG_SEQ(0x01, seq1); | |
| seq1 &= ~MGAREG_SEQ1_SCROFF; | |
| WREG_SEQ(0x01, seq1); | |
| msleep(20); | |
| RREG_ECRT(0x01, crtcext1); | |
| crtcext1 &= ~MGAREG_CRTCEXT1_VSYNCOFF; | |
| crtcext1 &= ~MGAREG_CRTCEXT1_HSYNCOFF; | |
| WREG_ECRT(0x01, crtcext1); | |
| } | |
| static void mgag200_disable_display(struct mga_device *mdev) | |
| { | |
| u8 seq0, seq1, crtcext1; | |
| RREG_SEQ(0x00, seq0); | |
| seq0 &= ~MGAREG_SEQ0_SYNCRST; | |
| WREG_SEQ(0x00, seq0); | |
| /* | |
| * TODO: replace busy waiting with vblank IRQ; put | |
| * msleep(50) before changing SCROFF | |
| */ | |
| mga_wait_vsync(mdev); | |
| mga_wait_busy(mdev); | |
| RREG_SEQ(0x01, seq1); | |
| seq1 |= MGAREG_SEQ1_SCROFF; | |
| WREG_SEQ(0x01, seq1); | |
| msleep(20); | |
| RREG_ECRT(0x01, crtcext1); | |
| crtcext1 |= MGAREG_CRTCEXT1_VSYNCOFF | | |
| MGAREG_CRTCEXT1_HSYNCOFF; | |
| WREG_ECRT(0x01, crtcext1); | |
| } | |
| /* | |
| * Connector | |
| */ | |
| static int mga_vga_get_modes(struct drm_connector *connector) | |
| { | |
| struct mga_connector *mga_connector = to_mga_connector(connector); | |
| struct edid *edid; | |
| int ret = 0; | |
| edid = drm_get_edid(connector, &mga_connector->i2c->adapter); | |
| if (edid) { | |
| drm_connector_update_edid_property(connector, edid); | |
| ret = drm_add_edid_modes(connector, edid); | |
| kfree(edid); | |
| } | |
| return ret; | |
| } | |
| static uint32_t mga_vga_calculate_mode_bandwidth(struct drm_display_mode *mode, | |
| int bits_per_pixel) | |
| { | |
| uint32_t total_area, divisor; | |
| uint64_t active_area, pixels_per_second, bandwidth; | |
| uint64_t bytes_per_pixel = (bits_per_pixel + 7) / 8; | |
| divisor = 1024; | |
| if (!mode->htotal || !mode->vtotal || !mode->clock) | |
| return 0; | |
| active_area = mode->hdisplay * mode->vdisplay; | |
| total_area = mode->htotal * mode->vtotal; | |
| pixels_per_second = active_area * mode->clock * 1000; | |
| do_div(pixels_per_second, total_area); | |
| bandwidth = pixels_per_second * bytes_per_pixel * 100; | |
| do_div(bandwidth, divisor); | |
| return (uint32_t)(bandwidth); | |
| } | |
| #define MODE_BANDWIDTH MODE_BAD | |
| static enum drm_mode_status mga_vga_mode_valid(struct drm_connector *connector, | |
| struct drm_display_mode *mode) | |
| { | |
| struct drm_device *dev = connector->dev; | |
| struct mga_device *mdev = to_mga_device(dev); | |
| int bpp = 32; | |
| if (IS_G200_SE(mdev)) { | |
| u32 unique_rev_id = mdev->model.g200se.unique_rev_id; | |
| if (unique_rev_id == 0x01) { | |
| if (mode->hdisplay > 1600) | |
| return MODE_VIRTUAL_X; | |
| if (mode->vdisplay > 1200) | |
| return MODE_VIRTUAL_Y; | |
| if (mga_vga_calculate_mode_bandwidth(mode, bpp) | |
| > (24400 * 1024)) | |
| return MODE_BANDWIDTH; | |
| } else if (unique_rev_id == 0x02) { | |
| if (mode->hdisplay > 1920) | |
| return MODE_VIRTUAL_X; | |
| if (mode->vdisplay > 1200) | |
| return MODE_VIRTUAL_Y; | |
| if (mga_vga_calculate_mode_bandwidth(mode, bpp) | |
| > (30100 * 1024)) | |
| return MODE_BANDWIDTH; | |
| } else { | |
| if (mga_vga_calculate_mode_bandwidth(mode, bpp) | |
| > (55000 * 1024)) | |
| return MODE_BANDWIDTH; | |
| } | |
| } else if (mdev->type == G200_WB) { | |
| if (mode->hdisplay > 1280) | |
| return MODE_VIRTUAL_X; | |
| if (mode->vdisplay > 1024) | |
| return MODE_VIRTUAL_Y; | |
| if (mga_vga_calculate_mode_bandwidth(mode, bpp) > | |
| (31877 * 1024)) | |
| return MODE_BANDWIDTH; | |
| } else if (mdev->type == G200_EV && | |
| (mga_vga_calculate_mode_bandwidth(mode, bpp) | |
| > (32700 * 1024))) { | |
| return MODE_BANDWIDTH; | |
| } else if (mdev->type == G200_EH && | |
| (mga_vga_calculate_mode_bandwidth(mode, bpp) | |
| > (37500 * 1024))) { | |
| return MODE_BANDWIDTH; | |
| } else if (mdev->type == G200_ER && | |
| (mga_vga_calculate_mode_bandwidth(mode, | |
| bpp) > (55000 * 1024))) { | |
| return MODE_BANDWIDTH; | |
| } | |
| if ((mode->hdisplay % 8) != 0 || (mode->hsync_start % 8) != 0 || | |
| (mode->hsync_end % 8) != 0 || (mode->htotal % 8) != 0) { | |
| return MODE_H_ILLEGAL; | |
| } | |
| if (mode->crtc_hdisplay > 2048 || mode->crtc_hsync_start > 4096 || | |
| mode->crtc_hsync_end > 4096 || mode->crtc_htotal > 4096 || | |
| mode->crtc_vdisplay > 2048 || mode->crtc_vsync_start > 4096 || | |
| mode->crtc_vsync_end > 4096 || mode->crtc_vtotal > 4096) { | |
| return MODE_BAD; | |
| } | |
| /* Validate the mode input by the user */ | |
| if (connector->cmdline_mode.specified) { | |
| if (connector->cmdline_mode.bpp_specified) | |
| bpp = connector->cmdline_mode.bpp; | |
| } | |
| if ((mode->hdisplay * mode->vdisplay * (bpp/8)) > mdev->vram_fb_available) { | |
| if (connector->cmdline_mode.specified) | |
| connector->cmdline_mode.specified = false; | |
| return MODE_BAD; | |
| } | |
| return MODE_OK; | |
| } | |
| static void mga_connector_destroy(struct drm_connector *connector) | |
| { | |
| struct mga_connector *mga_connector = to_mga_connector(connector); | |
| mgag200_i2c_destroy(mga_connector->i2c); | |
| drm_connector_cleanup(connector); | |
| } | |
| static const struct drm_connector_helper_funcs mga_vga_connector_helper_funcs = { | |
| .get_modes = mga_vga_get_modes, | |
| .mode_valid = mga_vga_mode_valid, | |
| }; | |
| static const struct drm_connector_funcs mga_vga_connector_funcs = { | |
| .reset = drm_atomic_helper_connector_reset, | |
| .fill_modes = drm_helper_probe_single_connector_modes, | |
| .destroy = mga_connector_destroy, | |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, | |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, | |
| }; | |
| static int mgag200_vga_connector_init(struct mga_device *mdev) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| struct mga_connector *mconnector = &mdev->connector; | |
| struct drm_connector *connector = &mconnector->base; | |
| struct mga_i2c_chan *i2c; | |
| int ret; | |
| i2c = mgag200_i2c_create(dev); | |
| if (!i2c) | |
| drm_warn(dev, "failed to add DDC bus\n"); | |
| ret = drm_connector_init_with_ddc(dev, connector, | |
| &mga_vga_connector_funcs, | |
| DRM_MODE_CONNECTOR_VGA, | |
| &i2c->adapter); | |
| if (ret) | |
| goto err_mgag200_i2c_destroy; | |
| drm_connector_helper_add(connector, &mga_vga_connector_helper_funcs); | |
| mconnector->i2c = i2c; | |
| return 0; | |
| err_mgag200_i2c_destroy: | |
| mgag200_i2c_destroy(i2c); | |
| return ret; | |
| } | |
| /* | |
| * Simple Display Pipe | |
| */ | |
| static enum drm_mode_status | |
| mgag200_simple_display_pipe_mode_valid(struct drm_simple_display_pipe *pipe, | |
| const struct drm_display_mode *mode) | |
| { | |
| return MODE_OK; | |
| } | |
| static void | |
| mgag200_handle_damage(struct mga_device *mdev, struct drm_framebuffer *fb, | |
| struct drm_rect *clip) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| struct dma_buf_map map; | |
| void *vmap; | |
| int ret; | |
| ret = drm_gem_shmem_vmap(fb->obj[0], &map); | |
| if (drm_WARN_ON(dev, ret)) | |
| return; /* BUG: SHMEM BO should always be vmapped */ | |
| vmap = map.vaddr; /* TODO: Use mapping abstraction properly */ | |
| drm_fb_memcpy_dstclip(mdev->vram, vmap, fb, clip); | |
| drm_gem_shmem_vunmap(fb->obj[0], &map); | |
| /* Always scanout image at VRAM offset 0 */ | |
| mgag200_set_startadd(mdev, (u32)0); | |
| mgag200_set_offset(mdev, fb); | |
| } | |
| static void | |
| mgag200_simple_display_pipe_enable(struct drm_simple_display_pipe *pipe, | |
| struct drm_crtc_state *crtc_state, | |
| struct drm_plane_state *plane_state) | |
| { | |
| struct drm_crtc *crtc = &pipe->crtc; | |
| struct drm_device *dev = crtc->dev; | |
| struct mga_device *mdev = to_mga_device(dev); | |
| struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode; | |
| struct drm_framebuffer *fb = plane_state->fb; | |
| struct drm_rect fullscreen = { | |
| .x1 = 0, | |
| .x2 = fb->width, | |
| .y1 = 0, | |
| .y2 = fb->height, | |
| }; | |
| if (mdev->type == G200_WB || mdev->type == G200_EW3) | |
| mgag200_g200wb_hold_bmc(mdev); | |
| mgag200_set_format_regs(mdev, fb); | |
| mgag200_set_mode_regs(mdev, adjusted_mode); | |
| mgag200_crtc_set_plls(mdev, adjusted_mode->clock); | |
| if (mdev->type == G200_ER) | |
| mgag200_g200er_reset_tagfifo(mdev); | |
| if (IS_G200_SE(mdev)) | |
| mgag200_g200se_set_hiprilvl(mdev, adjusted_mode, fb); | |
| else if (mdev->type == G200_EV) | |
| mgag200_g200ev_set_hiprilvl(mdev); | |
| if (mdev->type == G200_WB || mdev->type == G200_EW3) | |
| mgag200_g200wb_release_bmc(mdev); | |
| mga_crtc_load_lut(crtc); | |
| mgag200_enable_display(mdev); | |
| mgag200_handle_damage(mdev, fb, &fullscreen); | |
| } | |
| static void | |
| mgag200_simple_display_pipe_disable(struct drm_simple_display_pipe *pipe) | |
| { | |
| struct drm_crtc *crtc = &pipe->crtc; | |
| struct mga_device *mdev = to_mga_device(crtc->dev); | |
| mgag200_disable_display(mdev); | |
| } | |
| static int | |
| mgag200_simple_display_pipe_check(struct drm_simple_display_pipe *pipe, | |
| struct drm_plane_state *plane_state, | |
| struct drm_crtc_state *crtc_state) | |
| { | |
| struct drm_plane *plane = plane_state->plane; | |
| struct drm_framebuffer *new_fb = plane_state->fb; | |
| struct drm_framebuffer *fb = NULL; | |
| if (!new_fb) | |
| return 0; | |
| if (plane->state) | |
| fb = plane->state->fb; | |
| if (!fb || (fb->format != new_fb->format)) | |
| crtc_state->mode_changed = true; /* update PLL settings */ | |
| return 0; | |
| } | |
| static void | |
| mgag200_simple_display_pipe_update(struct drm_simple_display_pipe *pipe, | |
| struct drm_plane_state *old_state) | |
| { | |
| struct drm_plane *plane = &pipe->plane; | |
| struct drm_device *dev = plane->dev; | |
| struct mga_device *mdev = to_mga_device(dev); | |
| struct drm_plane_state *state = plane->state; | |
| struct drm_framebuffer *fb = state->fb; | |
| struct drm_rect damage; | |
| if (!fb) | |
| return; | |
| if (drm_atomic_helper_damage_merged(old_state, state, &damage)) | |
| mgag200_handle_damage(mdev, fb, &damage); | |
| } | |
| static const struct drm_simple_display_pipe_funcs | |
| mgag200_simple_display_pipe_funcs = { | |
| .mode_valid = mgag200_simple_display_pipe_mode_valid, | |
| .enable = mgag200_simple_display_pipe_enable, | |
| .disable = mgag200_simple_display_pipe_disable, | |
| .check = mgag200_simple_display_pipe_check, | |
| .update = mgag200_simple_display_pipe_update, | |
| .prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb, | |
| }; | |
| static const uint32_t mgag200_simple_display_pipe_formats[] = { | |
| DRM_FORMAT_XRGB8888, | |
| DRM_FORMAT_RGB565, | |
| DRM_FORMAT_RGB888, | |
| }; | |
| static const uint64_t mgag200_simple_display_pipe_fmtmods[] = { | |
| DRM_FORMAT_MOD_LINEAR, | |
| DRM_FORMAT_MOD_INVALID | |
| }; | |
| /* | |
| * Mode config | |
| */ | |
| static const struct drm_mode_config_funcs mgag200_mode_config_funcs = { | |
| .fb_create = drm_gem_fb_create_with_dirty, | |
| .atomic_check = drm_atomic_helper_check, | |
| .atomic_commit = drm_atomic_helper_commit, | |
| }; | |
| static unsigned int mgag200_preferred_depth(struct mga_device *mdev) | |
| { | |
| if (IS_G200_SE(mdev) && mdev->vram_fb_available < (2048*1024)) | |
| return 16; | |
| else | |
| return 32; | |
| } | |
| int mgag200_modeset_init(struct mga_device *mdev) | |
| { | |
| struct drm_device *dev = &mdev->base; | |
| struct drm_connector *connector = &mdev->connector.base; | |
| struct drm_simple_display_pipe *pipe = &mdev->display_pipe; | |
| size_t format_count = ARRAY_SIZE(mgag200_simple_display_pipe_formats); | |
| int ret; | |
| mdev->bpp_shifts[0] = 0; | |
| mdev->bpp_shifts[1] = 1; | |
| mdev->bpp_shifts[2] = 0; | |
| mdev->bpp_shifts[3] = 2; | |
| mgag200_init_regs(mdev); | |
| ret = drmm_mode_config_init(dev); | |
| if (ret) { | |
| drm_err(dev, "drmm_mode_config_init() failed, error %d\n", | |
| ret); | |
| return ret; | |
| } | |
| dev->mode_config.max_width = MGAG200_MAX_FB_WIDTH; | |
| dev->mode_config.max_height = MGAG200_MAX_FB_HEIGHT; | |
| dev->mode_config.preferred_depth = mgag200_preferred_depth(mdev); | |
| dev->mode_config.fb_base = mdev->mc.vram_base; | |
| dev->mode_config.funcs = &mgag200_mode_config_funcs; | |
| ret = mgag200_vga_connector_init(mdev); | |
| if (ret) { | |
| drm_err(dev, | |
| "mgag200_vga_connector_init() failed, error %d\n", | |
| ret); | |
| return ret; | |
| } | |
| ret = drm_simple_display_pipe_init(dev, pipe, | |
| &mgag200_simple_display_pipe_funcs, | |
| mgag200_simple_display_pipe_formats, | |
| format_count, | |
| mgag200_simple_display_pipe_fmtmods, | |
| connector); | |
| if (ret) { | |
| drm_err(dev, | |
| "drm_simple_display_pipe_init() failed, error %d\n", | |
| ret); | |
| return ret; | |
| } | |
| /* FIXME: legacy gamma tables; convert to CRTC state */ | |
| drm_mode_crtc_set_gamma_size(&pipe->crtc, MGAG200_LUT_SIZE); | |
| drm_mode_config_reset(dev); | |
| return 0; | |
| } |