| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright 2014 FEDEVEL, Inc. |
| * |
| * Author: Robert Nelson <robertcnelson@gmail.com> |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reg_3p3v: regulator@0 { |
| compatible = "regulator-fixed"; |
| reg = <0>; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_usbh1_vbus: regulator@1 { |
| compatible = "regulator-fixed"; |
| reg = <1>; |
| pinctrl-names = "default"; |
| regulator-name = "usbh1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_usb_otg_vbus: regulator@2 { |
| compatible = "regulator-fixed"; |
| reg = <2>; |
| pinctrl-names = "default"; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_led>; |
| |
| led0: usr { |
| label = "usr"; |
| gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; |
| default-state = "off"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| sound { |
| compatible = "fsl,imx6-rex-sgtl5000", |
| "fsl,imx-audio-sgtl5000"; |
| model = "imx6-rex-sgtl5000"; |
| ssi-controller = <&ssi1>; |
| audio-codec = <&codec>; |
| audio-routing = |
| "MIC_IN", "Mic Jack", |
| "Mic Jack", "Mic Bias", |
| "Headphone Jack", "HP_OUT"; |
| mux-int-port = <1>; |
| mux-ext-port = <3>; |
| }; |
| }; |
| |
| &audmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_audmux>; |
| status = "okay"; |
| }; |
| |
| &ecspi2 { |
| cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi2>; |
| status = "okay"; |
| }; |
| |
| &ecspi3 { |
| cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi3>; |
| status = "okay"; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet>; |
| phy-mode = "rgmii"; |
| phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| ddc-i2c-bus = <&i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| codec: sgtl5000@a { |
| compatible = "fsl,sgtl5000"; |
| reg = <0x0a>; |
| clocks = <&clks IMX6QDL_CLK_CKO>; |
| VDDA-supply = <®_3p3v>; |
| VDDIO-supply = <®_3p3v>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| eeprom@57 { |
| compatible = "atmel,24c02"; |
| reg = <0x57>; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| imx6qdl-rex { |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| /* SGTL5000 sys_mclk */ |
| MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0 |
| >; |
| }; |
| |
| pinctrl_audmux: audmuxgrp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 |
| MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 |
| MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 |
| MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 |
| >; |
| }; |
| |
| pinctrl_ecspi2: ecspi2grp { |
| fsl,pins = < |
| MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 |
| MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 |
| MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 |
| /* CS */ |
| MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x000b1 |
| >; |
| }; |
| |
| pinctrl_ecspi3: ecspi3grp { |
| fsl,pins = < |
| MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1 |
| MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1 |
| MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1 |
| /* CS */ |
| MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x000b1 |
| >; |
| }; |
| |
| pinctrl_enet: enetgrp { |
| fsl,pins = < |
| MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 |
| MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 |
| MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030 |
| MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030 |
| MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030 |
| MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030 |
| MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030 |
| MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030 |
| MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 |
| MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030 |
| MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030 |
| MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030 |
| MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030 |
| MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 |
| MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 |
| MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 |
| /* Phy reset */ |
| MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x000b0 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 |
| MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_led: ledgrp { |
| fsl,pins = < |
| /* user led */ |
| MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbh1: usbh1grp { |
| fsl,pins = < |
| /* power enable, high active */ |
| MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x10b0 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 |
| /* power enable, high active */ |
| MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x10b0 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 |
| MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 |
| MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 |
| MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 |
| MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 |
| MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 |
| /* CD */ |
| MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 |
| /* WP */ |
| MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1f0b0 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 |
| /* CD */ |
| MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0 |
| /* WP */ |
| MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1f0b0 |
| >; |
| }; |
| }; |
| }; |
| |
| &ssi1 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usbh1_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbh1>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2>; |
| bus-width = <4>; |
| cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| bus-width = <4>; |
| cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
