| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include <dt-bindings/clock/rk3288-cru.h> |
| #include <dt-bindings/power/rk3288-power.h> |
| #include <dt-bindings/thermal/thermal.h> |
| #include <dt-bindings/soc/rockchip,boot-mode.h> |
| |
| / { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| compatible = "rockchip,rk3288"; |
| |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| ethernet0 = &gmac; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| mshc0 = &emmc; |
| mshc1 = &sdmmc; |
| mshc2 = &sdio0; |
| mshc3 = &sdio1; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| serial3 = &uart3; |
| serial4 = &uart4; |
| spi0 = &spi0; |
| spi1 = &spi1; |
| spi2 = &spi2; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a12-pmu"; |
| interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "rockchip,rk3066-smp"; |
| rockchip,pmu = <&pmu>; |
| |
| cpu0: cpu@500 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a12"; |
| reg = <0x500>; |
| resets = <&cru SRST_CORE0>; |
| operating-points-v2 = <&cpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| dynamic-power-coefficient = <370>; |
| }; |
| cpu1: cpu@501 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a12"; |
| reg = <0x501>; |
| resets = <&cru SRST_CORE1>; |
| operating-points-v2 = <&cpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| dynamic-power-coefficient = <370>; |
| }; |
| cpu2: cpu@502 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a12"; |
| reg = <0x502>; |
| resets = <&cru SRST_CORE2>; |
| operating-points-v2 = <&cpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| dynamic-power-coefficient = <370>; |
| }; |
| cpu3: cpu@503 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a12"; |
| reg = <0x503>; |
| resets = <&cru SRST_CORE3>; |
| operating-points-v2 = <&cpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| dynamic-power-coefficient = <370>; |
| }; |
| }; |
| |
| cpu_opp_table: opp-table-0 { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-126000000 { |
| opp-hz = /bits/ 64 <126000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-216000000 { |
| opp-hz = /bits/ 64 <216000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-312000000 { |
| opp-hz = /bits/ 64 <312000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-408000000 { |
| opp-hz = /bits/ 64 <408000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-696000000 { |
| opp-hz = /bits/ 64 <696000000>; |
| opp-microvolt = <950000>; |
| }; |
| opp-816000000 { |
| opp-hz = /bits/ 64 <816000000>; |
| opp-microvolt = <1000000>; |
| }; |
| opp-1008000000 { |
| opp-hz = /bits/ 64 <1008000000>; |
| opp-microvolt = <1050000>; |
| }; |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-1416000000 { |
| opp-hz = /bits/ 64 <1416000000>; |
| opp-microvolt = <1200000>; |
| }; |
| opp-1512000000 { |
| opp-hz = /bits/ 64 <1512000000>; |
| opp-microvolt = <1300000>; |
| }; |
| opp-1608000000 { |
| opp-hz = /bits/ 64 <1608000000>; |
| opp-microvolt = <1350000>; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| /* |
| * The rk3288 cannot use the memory area above 0xfe000000 |
| * for dma operations for some reason. While there is |
| * probably a better solution available somewhere, we |
| * haven't found it yet and while devices with 2GB of ram |
| * are not affected, this issue prevents 4GB from booting. |
| * So to make these devices at least bootable, block |
| * this area for the time being until the real solution |
| * is found. |
| */ |
| dma-unusable@fe000000 { |
| reg = <0x0 0xfe000000 0x0 0x1000000>; |
| }; |
| }; |
| |
| xin24m: oscillator { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xin24m"; |
| #clock-cells = <0>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| arm,cpu-registers-not-fw-configured; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| clock-frequency = <24000000>; |
| arm,no-tick-in-suspend; |
| }; |
| |
| timer: timer@ff810000 { |
| compatible = "rockchip,rk3288-timer"; |
| reg = <0x0 0xff810000 0x0 0x20>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_TIMER>, <&xin24m>; |
| clock-names = "pclk", "timer"; |
| }; |
| |
| display-subsystem { |
| compatible = "rockchip,display-subsystem"; |
| ports = <&vopl_out>, <&vopb_out>; |
| }; |
| |
| sdmmc: mmc@ff0c0000 { |
| compatible = "rockchip,rk3288-dw-mshc"; |
| max-frequency = <150000000>; |
| clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, |
| <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0c0000 0x0 0x4000>; |
| resets = <&cru SRST_MMC0>; |
| reset-names = "reset"; |
| status = "disabled"; |
| }; |
| |
| sdio0: mmc@ff0d0000 { |
| compatible = "rockchip,rk3288-dw-mshc"; |
| max-frequency = <150000000>; |
| clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>, |
| <&cru SCLK_SDIO0_DRV>, <&cru SCLK_SDIO0_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0d0000 0x0 0x4000>; |
| resets = <&cru SRST_SDIO0>; |
| reset-names = "reset"; |
| status = "disabled"; |
| }; |
| |
| sdio1: mmc@ff0e0000 { |
| compatible = "rockchip,rk3288-dw-mshc"; |
| max-frequency = <150000000>; |
| clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>, |
| <&cru SCLK_SDIO1_DRV>, <&cru SCLK_SDIO1_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0e0000 0x0 0x4000>; |
| resets = <&cru SRST_SDIO1>; |
| reset-names = "reset"; |
| status = "disabled"; |
| }; |
| |
| emmc: mmc@ff0f0000 { |
| compatible = "rockchip,rk3288-dw-mshc"; |
| max-frequency = <150000000>; |
| clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, |
| <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0f0000 0x0 0x4000>; |
| resets = <&cru SRST_EMMC>; |
| reset-names = "reset"; |
| status = "disabled"; |
| }; |
| |
| saradc: saradc@ff100000 { |
| compatible = "rockchip,saradc"; |
| reg = <0x0 0xff100000 0x0 0x100>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| #io-channel-cells = <1>; |
| clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; |
| clock-names = "saradc", "apb_pclk"; |
| resets = <&cru SRST_SARADC>; |
| reset-names = "saradc-apb"; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@ff110000 { |
| compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi"; |
| clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; |
| clock-names = "spiclk", "apb_pclk"; |
| dmas = <&dmac_peri 11>, <&dmac_peri 12>; |
| dma-names = "tx", "rx"; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; |
| reg = <0x0 0xff110000 0x0 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@ff120000 { |
| compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi"; |
| clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>; |
| clock-names = "spiclk", "apb_pclk"; |
| dmas = <&dmac_peri 13>, <&dmac_peri 14>; |
| dma-names = "tx", "rx"; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; |
| reg = <0x0 0xff120000 0x0 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi2: spi@ff130000 { |
| compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi"; |
| clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>; |
| clock-names = "spiclk", "apb_pclk"; |
| dmas = <&dmac_peri 15>, <&dmac_peri 16>; |
| dma-names = "tx", "rx"; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>; |
| reg = <0x0 0xff130000 0x0 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@ff140000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff140000 0x0 0x1000>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_xfer>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@ff150000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff150000 0x0 0x1000>; |
| interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_xfer>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@ff160000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff160000 0x0 0x1000>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c4_xfer>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@ff170000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff170000 0x0 0x1000>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c5_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@ff180000 { |
| compatible = "rockchip,rk3288-uart", "snps,dw-apb-uart"; |
| reg = <0x0 0xff180000 0x0 0x100>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac_peri 1>, <&dmac_peri 2>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@ff190000 { |
| compatible = "rockchip,rk3288-uart", "snps,dw-apb-uart"; |
| reg = <0x0 0xff190000 0x0 0x100>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac_peri 3>, <&dmac_peri 4>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@ff690000 { |
| compatible = "rockchip,rk3288-uart", "snps,dw-apb-uart"; |
| reg = <0x0 0xff690000 0x0 0x100>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; |
| clock-names = "baudclk", "apb_pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@ff1b0000 { |
| compatible = "rockchip,rk3288-uart", "snps,dw-apb-uart"; |
| reg = <0x0 0xff1b0000 0x0 0x100>; |
| interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac_peri 7>, <&dmac_peri 8>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_xfer>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@ff1c0000 { |
| compatible = "rockchip,rk3288-uart", "snps,dw-apb-uart"; |
| reg = <0x0 0xff1c0000 0x0 0x100>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac_peri 9>, <&dmac_peri 10>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart4_xfer>; |
| status = "disabled"; |
| }; |
| |
| dmac_peri: dma-controller@ff250000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x0 0xff250000 0x0 0x4000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| arm,pl330-broken-no-flushp; |
| arm,pl330-periph-burst; |
| clocks = <&cru ACLK_DMAC2>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| thermal-zones { |
| reserve_thermal: reserve-thermal { |
| polling-delay-passive = <1000>; /* milliseconds */ |
| polling-delay = <5000>; /* milliseconds */ |
| |
| thermal-sensors = <&tsadc 0>; |
| }; |
| |
| cpu_thermal: cpu-thermal { |
| polling-delay-passive = <100>; /* milliseconds */ |
| polling-delay = <5000>; /* milliseconds */ |
| |
| thermal-sensors = <&tsadc 1>; |
| |
| trips { |
| cpu_alert0: cpu_alert0 { |
| temperature = <70000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| cpu_alert1: cpu_alert1 { |
| temperature = <75000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| cpu_crit: cpu_crit { |
| temperature = <90000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu_alert0>; |
| cooling-device = |
| <&cpu0 THERMAL_NO_LIMIT 6>, |
| <&cpu1 THERMAL_NO_LIMIT 6>, |
| <&cpu2 THERMAL_NO_LIMIT 6>, |
| <&cpu3 THERMAL_NO_LIMIT 6>; |
| }; |
| map1 { |
| trip = <&cpu_alert1>; |
| cooling-device = |
| <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| gpu_thermal: gpu-thermal { |
| polling-delay-passive = <100>; /* milliseconds */ |
| polling-delay = <5000>; /* milliseconds */ |
| |
| thermal-sensors = <&tsadc 2>; |
| |
| trips { |
| gpu_alert0: gpu_alert0 { |
| temperature = <70000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| gpu_crit: gpu_crit { |
| temperature = <90000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&gpu_alert0>; |
| cooling-device = |
| <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| tsadc: tsadc@ff280000 { |
| compatible = "rockchip,rk3288-tsadc"; |
| reg = <0x0 0xff280000 0x0 0x100>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; |
| clock-names = "tsadc", "apb_pclk"; |
| resets = <&cru SRST_TSADC>; |
| reset-names = "tsadc-apb"; |
| pinctrl-names = "init", "default", "sleep"; |
| pinctrl-0 = <&otp_pin>; |
| pinctrl-1 = <&otp_out>; |
| pinctrl-2 = <&otp_pin>; |
| #thermal-sensor-cells = <1>; |
| rockchip,grf = <&grf>; |
| rockchip,hw-tshut-temp = <95000>; |
| status = "disabled"; |
| }; |
| |
| gmac: ethernet@ff290000 { |
| compatible = "rockchip,rk3288-gmac"; |
| reg = <0x0 0xff290000 0x0 0x10000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq", "eth_wake_irq"; |
| rockchip,grf = <&grf>; |
| clocks = <&cru SCLK_MAC>, |
| <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>, |
| <&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>, |
| <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; |
| clock-names = "stmmaceth", |
| "mac_clk_rx", "mac_clk_tx", |
| "clk_mac_ref", "clk_mac_refout", |
| "aclk_mac", "pclk_mac"; |
| resets = <&cru SRST_MAC>; |
| reset-names = "stmmaceth"; |
| status = "disabled"; |
| }; |
| |
| usb_host0_ehci: usb@ff500000 { |
| compatible = "generic-ehci"; |
| reg = <0x0 0xff500000 0x0 0x100>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_USBHOST0>; |
| phys = <&usbphy1>; |
| phy-names = "usb"; |
| status = "disabled"; |
| }; |
| |
| /* NOTE: doesn't work on RK3288, but was fixed on RK3288W */ |
| usb_host0_ohci: usb@ff520000 { |
| compatible = "generic-ohci"; |
| reg = <0x0 0xff520000 0x0 0x100>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_USBHOST0>; |
| phys = <&usbphy1>; |
| phy-names = "usb"; |
| status = "disabled"; |
| }; |
| |
| usb_host1: usb@ff540000 { |
| compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", |
| "snps,dwc2"; |
| reg = <0x0 0xff540000 0x0 0x40000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_USBHOST1>; |
| clock-names = "otg"; |
| dr_mode = "host"; |
| phys = <&usbphy2>; |
| phy-names = "usb2-phy"; |
| snps,reset-phy-on-wake; |
| status = "disabled"; |
| }; |
| |
| usb_otg: usb@ff580000 { |
| compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", |
| "snps,dwc2"; |
| reg = <0x0 0xff580000 0x0 0x40000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_OTG0>; |
| clock-names = "otg"; |
| dr_mode = "otg"; |
| g-np-tx-fifo-size = <16>; |
| g-rx-fifo-size = <275>; |
| g-tx-fifo-size = <256 128 128 64 64 32>; |
| phys = <&usbphy0>; |
| phy-names = "usb2-phy"; |
| status = "disabled"; |
| }; |
| |
| usb_hsic: usb@ff5c0000 { |
| compatible = "generic-ehci"; |
| reg = <0x0 0xff5c0000 0x0 0x100>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_HSIC>; |
| status = "disabled"; |
| }; |
| |
| dmac_bus_ns: dma-controller@ff600000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x0 0xff600000 0x0 0x4000>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| arm,pl330-broken-no-flushp; |
| arm,pl330-periph-burst; |
| clocks = <&cru ACLK_DMAC1>; |
| clock-names = "apb_pclk"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@ff650000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff650000 0x0 0x1000>; |
| interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_xfer>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@ff660000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x0 0xff660000 0x0 0x1000>; |
| interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_xfer>; |
| status = "disabled"; |
| }; |
| |
| pwm0: pwm@ff680000 { |
| compatible = "rockchip,rk3288-pwm"; |
| reg = <0x0 0xff680000 0x0 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm0_pin>; |
| clocks = <&cru PCLK_RKPWM>; |
| status = "disabled"; |
| }; |
| |
| pwm1: pwm@ff680010 { |
| compatible = "rockchip,rk3288-pwm"; |
| reg = <0x0 0xff680010 0x0 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm1_pin>; |
| clocks = <&cru PCLK_RKPWM>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@ff680020 { |
| compatible = "rockchip,rk3288-pwm"; |
| reg = <0x0 0xff680020 0x0 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm2_pin>; |
| clocks = <&cru PCLK_RKPWM>; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@ff680030 { |
| compatible = "rockchip,rk3288-pwm"; |
| reg = <0x0 0xff680030 0x0 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm3_pin>; |
| clocks = <&cru PCLK_RKPWM>; |
| status = "disabled"; |
| }; |
| |
| bus_intmem: sram@ff700000 { |
| compatible = "mmio-sram"; |
| reg = <0x0 0xff700000 0x0 0x18000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x0 0xff700000 0x18000>; |
| smp-sram@0 { |
| compatible = "rockchip,rk3066-smp-sram"; |
| reg = <0x00 0x10>; |
| }; |
| }; |
| |
| pmu_sram: sram@ff720000 { |
| compatible = "rockchip,rk3288-pmu-sram", "mmio-sram"; |
| reg = <0x0 0xff720000 0x0 0x1000>; |
| }; |
| |
| pmu: power-management@ff730000 { |
| compatible = "rockchip,rk3288-pmu", "syscon", "simple-mfd"; |
| reg = <0x0 0xff730000 0x0 0x100>; |
| |
| power: power-controller { |
| compatible = "rockchip,rk3288-power-controller"; |
| #power-domain-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| assigned-clocks = <&cru SCLK_EDP_24M>; |
| assigned-clock-parents = <&xin24m>; |
| |
| /* |
| * Note: Although SCLK_* are the working clocks |
| * of device without including on the NOC, needed for |
| * synchronous reset. |
| * |
| * The clocks on the which NOC: |
| * ACLK_IEP/ACLK_VIP/ACLK_VOP0 are on ACLK_VIO0_NIU. |
| * ACLK_ISP/ACLK_VOP1 are on ACLK_VIO1_NIU. |
| * ACLK_RGA is on ACLK_RGA_NIU. |
| * The others (HCLK_*,PLCK_*) are on HCLK_VIO_NIU. |
| * |
| * Which clock are device clocks: |
| * clocks devices |
| * *_IEP IEP:Image Enhancement Processor |
| * *_ISP ISP:Image Signal Processing |
| * *_VIP VIP:Video Input Processor |
| * *_VOP* VOP:Visual Output Processor |
| * *_RGA RGA |
| * *_EDP* EDP |
| * *_LVDS_* LVDS |
| * *_HDMI HDMI |
| * *_MIPI_* MIPI |
| */ |
| power-domain@RK3288_PD_VIO { |
| reg = <RK3288_PD_VIO>; |
| clocks = <&cru ACLK_IEP>, |
| <&cru ACLK_ISP>, |
| <&cru ACLK_RGA>, |
| <&cru ACLK_VIP>, |
| <&cru ACLK_VOP0>, |
| <&cru ACLK_VOP1>, |
| <&cru DCLK_VOP0>, |
| <&cru DCLK_VOP1>, |
| <&cru HCLK_IEP>, |
| <&cru HCLK_ISP>, |
| <&cru HCLK_RGA>, |
| <&cru HCLK_VIP>, |
| <&cru HCLK_VOP0>, |
| <&cru HCLK_VOP1>, |
| <&cru PCLK_EDP_CTRL>, |
| <&cru PCLK_HDMI_CTRL>, |
| <&cru PCLK_LVDS_PHY>, |
| <&cru PCLK_MIPI_CSI>, |
| <&cru PCLK_MIPI_DSI0>, |
| <&cru PCLK_MIPI_DSI1>, |
| <&cru SCLK_EDP_24M>, |
| <&cru SCLK_EDP>, |
| <&cru SCLK_ISP_JPE>, |
| <&cru SCLK_ISP>, |
| <&cru SCLK_RGA>; |
| pm_qos = <&qos_vio0_iep>, |
| <&qos_vio1_vop>, |
| <&qos_vio1_isp_w0>, |
| <&qos_vio1_isp_w1>, |
| <&qos_vio0_vop>, |
| <&qos_vio0_vip>, |
| <&qos_vio2_rga_r>, |
| <&qos_vio2_rga_w>, |
| <&qos_vio1_isp_r>; |
| #power-domain-cells = <0>; |
| }; |
| |
| /* |
| * Note: The following 3 are HEVC(H.265) clocks, |
| * and on the ACLK_HEVC_NIU (NOC). |
| */ |
| power-domain@RK3288_PD_HEVC { |
| reg = <RK3288_PD_HEVC>; |
| clocks = <&cru ACLK_HEVC>, |
| <&cru SCLK_HEVC_CABAC>, |
| <&cru SCLK_HEVC_CORE>; |
| pm_qos = <&qos_hevc_r>, |
| <&qos_hevc_w>; |
| #power-domain-cells = <0>; |
| }; |
| |
| /* |
| * Note: ACLK_VCODEC/HCLK_VCODEC are VCODEC |
| * (video endecoder & decoder) clocks that on the |
| * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC). |
| */ |
| power-domain@RK3288_PD_VIDEO { |
| reg = <RK3288_PD_VIDEO>; |
| clocks = <&cru ACLK_VCODEC>, |
| <&cru HCLK_VCODEC>; |
| pm_qos = <&qos_video>; |
| #power-domain-cells = <0>; |
| }; |
| |
| /* |
| * Note: ACLK_GPU is the GPU clock, |
| * and on the ACLK_GPU_NIU (NOC). |
| */ |
| power-domain@RK3288_PD_GPU { |
| reg = <RK3288_PD_GPU>; |
| clocks = <&cru ACLK_GPU>; |
| pm_qos = <&qos_gpu_r>, |
| <&qos_gpu_w>; |
| #power-domain-cells = <0>; |
| }; |
| }; |
| |
| reboot-mode { |
| compatible = "syscon-reboot-mode"; |
| offset = <0x94>; |
| mode-normal = <BOOT_NORMAL>; |
| mode-recovery = <BOOT_RECOVERY>; |
| mode-bootloader = <BOOT_FASTBOOT>; |
| mode-loader = <BOOT_BL_DOWNLOAD>; |
| }; |
| }; |
| |
| sgrf: syscon@ff740000 { |
| compatible = "rockchip,rk3288-sgrf", "syscon"; |
| reg = <0x0 0xff740000 0x0 0x1000>; |
| }; |
| |
| cru: clock-controller@ff760000 { |
| compatible = "rockchip,rk3288-cru"; |
| reg = <0x0 0xff760000 0x0 0x1000>; |
| clocks = <&xin24m>; |
| clock-names = "xin24m"; |
| rockchip,grf = <&grf>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| assigned-clocks = <&cru PLL_GPLL>, <&cru PLL_CPLL>, |
| <&cru PLL_NPLL>, <&cru ACLK_CPU>, |
| <&cru HCLK_CPU>, <&cru PCLK_CPU>, |
| <&cru ACLK_PERI>, <&cru HCLK_PERI>, |
| <&cru PCLK_PERI>; |
| assigned-clock-rates = <594000000>, <400000000>, |
| <500000000>, <300000000>, |
| <150000000>, <75000000>, |
| <300000000>, <150000000>, |
| <75000000>; |
| }; |
| |
| grf: syscon@ff770000 { |
| compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; |
| reg = <0x0 0xff770000 0x0 0x1000>; |
| |
| edp_phy: edp-phy { |
| compatible = "rockchip,rk3288-dp-phy"; |
| clocks = <&cru SCLK_EDP_24M>; |
| clock-names = "24m"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| io_domains: io-domains { |
| compatible = "rockchip,rk3288-io-voltage-domain"; |
| status = "disabled"; |
| }; |
| |
| usbphy: usbphy { |
| compatible = "rockchip,rk3288-usb-phy"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| usbphy0: usb-phy@320 { |
| #phy-cells = <0>; |
| reg = <0x320>; |
| clocks = <&cru SCLK_OTGPHY0>; |
| clock-names = "phyclk"; |
| #clock-cells = <0>; |
| resets = <&cru SRST_USBOTG_PHY>; |
| reset-names = "phy-reset"; |
| }; |
| |
| usbphy1: usb-phy@334 { |
| #phy-cells = <0>; |
| reg = <0x334>; |
| clocks = <&cru SCLK_OTGPHY1>; |
| clock-names = "phyclk"; |
| #clock-cells = <0>; |
| resets = <&cru SRST_USBHOST0_PHY>; |
| reset-names = "phy-reset"; |
| }; |
| |
| usbphy2: usb-phy@348 { |
| #phy-cells = <0>; |
| reg = <0x348>; |
| clocks = <&cru SCLK_OTGPHY2>; |
| clock-names = "phyclk"; |
| #clock-cells = <0>; |
| resets = <&cru SRST_USBHOST1_PHY>; |
| reset-names = "phy-reset"; |
| }; |
| }; |
| }; |
| |
| wdt: watchdog@ff800000 { |
| compatible = "rockchip,rk3288-wdt", "snps,dw-wdt"; |
| reg = <0x0 0xff800000 0x0 0x100>; |
| clocks = <&cru PCLK_WDT>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| spdif: sound@ff8b0000 { |
| compatible = "rockchip,rk3288-spdif", "rockchip,rk3066-spdif"; |
| reg = <0x0 0xff8b0000 0x0 0x10000>; |
| #sound-dai-cells = <0>; |
| clocks = <&cru SCLK_SPDIF8CH>, <&cru HCLK_SPDIF8CH>; |
| clock-names = "mclk", "hclk"; |
| dmas = <&dmac_bus_s 3>; |
| dma-names = "tx"; |
| interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spdif_tx>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| }; |
| |
| i2s: i2s@ff890000 { |
| compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; |
| reg = <0x0 0xff890000 0x0 0x10000>; |
| #sound-dai-cells = <0>; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>; |
| clock-names = "i2s_clk", "i2s_hclk"; |
| dmas = <&dmac_bus_s 0>, <&dmac_bus_s 1>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2s0_bus>; |
| rockchip,playback-channels = <8>; |
| rockchip,capture-channels = <2>; |
| status = "disabled"; |
| }; |
| |
| crypto: crypto@ff8a0000 { |
| compatible = "rockchip,rk3288-crypto"; |
| reg = <0x0 0xff8a0000 0x0 0x4000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_CRYPTO>, <&cru HCLK_CRYPTO>, |
| <&cru SCLK_CRYPTO>, <&cru ACLK_DMAC1>; |
| clock-names = "aclk", "hclk", "sclk", "apb_pclk"; |
| resets = <&cru SRST_CRYPTO>; |
| reset-names = "crypto-rst"; |
| }; |
| |
| iep_mmu: iommu@ff900800 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff900800 0x0 0x40>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>; |
| clock-names = "aclk", "iface"; |
| #iommu-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| isp_mmu: iommu@ff914000 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff914000 0x0 0x100>, <0x0 0xff915000 0x0 0x100>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_ISP>, <&cru HCLK_ISP>; |
| clock-names = "aclk", "iface"; |
| #iommu-cells = <0>; |
| rockchip,disable-mmu-reset; |
| status = "disabled"; |
| }; |
| |
| rga: rga@ff920000 { |
| compatible = "rockchip,rk3288-rga"; |
| reg = <0x0 0xff920000 0x0 0x180>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_RGA>, <&cru HCLK_RGA>, <&cru SCLK_RGA>; |
| clock-names = "aclk", "hclk", "sclk"; |
| power-domains = <&power RK3288_PD_VIO>; |
| resets = <&cru SRST_RGA_CORE>, <&cru SRST_RGA_AXI>, <&cru SRST_RGA_AHB>; |
| reset-names = "core", "axi", "ahb"; |
| }; |
| |
| vopb: vop@ff930000 { |
| compatible = "rockchip,rk3288-vop"; |
| reg = <0x0 0xff930000 0x0 0x19c>, <0x0 0xff931000 0x0 0x1000>; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>; |
| clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; |
| power-domains = <&power RK3288_PD_VIO>; |
| resets = <&cru SRST_LCDC0_AXI>, <&cru SRST_LCDC0_AHB>, <&cru SRST_LCDC0_DCLK>; |
| reset-names = "axi", "ahb", "dclk"; |
| iommus = <&vopb_mmu>; |
| status = "disabled"; |
| |
| vopb_out: port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vopb_out_hdmi: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&hdmi_in_vopb>; |
| }; |
| |
| vopb_out_edp: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&edp_in_vopb>; |
| }; |
| |
| vopb_out_mipi: endpoint@2 { |
| reg = <2>; |
| remote-endpoint = <&mipi_in_vopb>; |
| }; |
| |
| vopb_out_lvds: endpoint@3 { |
| reg = <3>; |
| remote-endpoint = <&lvds_in_vopb>; |
| }; |
| }; |
| }; |
| |
| vopb_mmu: iommu@ff930300 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff930300 0x0 0x100>; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_VOP0>, <&cru HCLK_VOP0>; |
| clock-names = "aclk", "iface"; |
| power-domains = <&power RK3288_PD_VIO>; |
| #iommu-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| vopl: vop@ff940000 { |
| compatible = "rockchip,rk3288-vop"; |
| reg = <0x0 0xff940000 0x0 0x19c>, <0x0 0xff941000 0x0 0x1000>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_VOP1>, <&cru DCLK_VOP1>, <&cru HCLK_VOP1>; |
| clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; |
| power-domains = <&power RK3288_PD_VIO>; |
| resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; |
| reset-names = "axi", "ahb", "dclk"; |
| iommus = <&vopl_mmu>; |
| status = "disabled"; |
| |
| vopl_out: port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vopl_out_hdmi: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&hdmi_in_vopl>; |
| }; |
| |
| vopl_out_edp: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&edp_in_vopl>; |
| }; |
| |
| vopl_out_mipi: endpoint@2 { |
| reg = <2>; |
| remote-endpoint = <&mipi_in_vopl>; |
| }; |
| |
| vopl_out_lvds: endpoint@3 { |
| reg = <3>; |
| remote-endpoint = <&lvds_in_vopl>; |
| }; |
| }; |
| }; |
| |
| vopl_mmu: iommu@ff940300 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff940300 0x0 0x100>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>; |
| clock-names = "aclk", "iface"; |
| power-domains = <&power RK3288_PD_VIO>; |
| #iommu-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| mipi_dsi: mipi@ff960000 { |
| compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi"; |
| reg = <0x0 0xff960000 0x0 0x4000>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_MIPIDSI_24M>, <&cru PCLK_MIPI_DSI0>; |
| clock-names = "ref", "pclk"; |
| power-domains = <&power RK3288_PD_VIO>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| |
| ports { |
| mipi_in: port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| mipi_in_vopb: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&vopb_out_mipi>; |
| }; |
| mipi_in_vopl: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&vopl_out_mipi>; |
| }; |
| }; |
| }; |
| }; |
| |
| lvds: lvds@ff96c000 { |
| compatible = "rockchip,rk3288-lvds"; |
| reg = <0x0 0xff96c000 0x0 0x4000>; |
| clocks = <&cru PCLK_LVDS_PHY>; |
| clock-names = "pclk_lvds"; |
| pinctrl-names = "lcdc"; |
| pinctrl-0 = <&lcdc_ctl>; |
| power-domains = <&power RK3288_PD_VIO>; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| lvds_in: port@0 { |
| reg = <0>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| lvds_in_vopb: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&vopb_out_lvds>; |
| }; |
| lvds_in_vopl: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&vopl_out_lvds>; |
| }; |
| }; |
| }; |
| }; |
| |
| edp: dp@ff970000 { |
| compatible = "rockchip,rk3288-dp"; |
| reg = <0x0 0xff970000 0x0 0x4000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; |
| clock-names = "dp", "pclk"; |
| phys = <&edp_phy>; |
| phy-names = "dp"; |
| power-domains = <&power RK3288_PD_VIO>; |
| resets = <&cru SRST_EDP>; |
| reset-names = "dp"; |
| rockchip,grf = <&grf>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| edp_in: port@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| edp_in_vopb: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&vopb_out_edp>; |
| }; |
| edp_in_vopl: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&vopl_out_edp>; |
| }; |
| }; |
| }; |
| }; |
| |
| hdmi: hdmi@ff980000 { |
| compatible = "rockchip,rk3288-dw-hdmi"; |
| reg = <0x0 0xff980000 0x0 0x20000>; |
| reg-io-width = <4>; |
| #sound-dai-cells = <0>; |
| rockchip,grf = <&grf>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>, <&cru SCLK_HDMI_CEC>; |
| clock-names = "iahb", "isfr", "cec"; |
| power-domains = <&power RK3288_PD_VIO>; |
| status = "disabled"; |
| |
| ports { |
| hdmi_in: port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| hdmi_in_vopb: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&vopb_out_hdmi>; |
| }; |
| hdmi_in_vopl: endpoint@1 { |
| reg = <1>; |
| remote-endpoint = <&vopl_out_hdmi>; |
| }; |
| }; |
| }; |
| }; |
| |
| vpu: video-codec@ff9a0000 { |
| compatible = "rockchip,rk3288-vpu"; |
| reg = <0x0 0xff9a0000 0x0 0x800>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "vepu", "vdpu"; |
| clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>; |
| clock-names = "aclk", "hclk"; |
| iommus = <&vpu_mmu>; |
| power-domains = <&power RK3288_PD_VIDEO>; |
| }; |
| |
| vpu_mmu: iommu@ff9a0800 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff9a0800 0x0 0x100>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>; |
| clock-names = "aclk", "iface"; |
| #iommu-cells = <0>; |
| power-domains = <&power RK3288_PD_VIDEO>; |
| }; |
| |
| hevc_mmu: iommu@ff9c0440 { |
| compatible = "rockchip,iommu"; |
| reg = <0x0 0xff9c0440 0x0 0x40>, <0x0 0xff9c0480 0x0 0x40>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru ACLK_HEVC>, <&cru HCLK_HEVC>; |
| clock-names = "aclk", "iface"; |
| #iommu-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| gpu: gpu@ffa30000 { |
| compatible = "rockchip,rk3288-mali", "arm,mali-t760"; |
| reg = <0x0 0xffa30000 0x0 0x10000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "job", "mmu", "gpu"; |
| clocks = <&cru ACLK_GPU>; |
| operating-points-v2 = <&gpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| power-domains = <&power RK3288_PD_GPU>; |
| status = "disabled"; |
| }; |
| |
| gpu_opp_table: opp-table-1 { |
| compatible = "operating-points-v2"; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| opp-microvolt = <950000>; |
| }; |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| opp-microvolt = <950000>; |
| }; |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-microvolt = <1000000>; |
| }; |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <1250000>; |
| }; |
| }; |
| |
| qos_gpu_r: qos@ffaa0000 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffaa0000 0x0 0x20>; |
| }; |
| |
| qos_gpu_w: qos@ffaa0080 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffaa0080 0x0 0x20>; |
| }; |
| |
| qos_vio1_vop: qos@ffad0000 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0000 0x0 0x20>; |
| }; |
| |
| qos_vio1_isp_w0: qos@ffad0100 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0100 0x0 0x20>; |
| }; |
| |
| qos_vio1_isp_w1: qos@ffad0180 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0180 0x0 0x20>; |
| }; |
| |
| qos_vio0_vop: qos@ffad0400 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0400 0x0 0x20>; |
| }; |
| |
| qos_vio0_vip: qos@ffad0480 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0480 0x0 0x20>; |
| }; |
| |
| qos_vio0_iep: qos@ffad0500 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0500 0x0 0x20>; |
| }; |
| |
| qos_vio2_rga_r: qos@ffad0800 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0800 0x0 0x20>; |
| }; |
| |
| qos_vio2_rga_w: qos@ffad0880 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0880 0x0 0x20>; |
| }; |
| |
| qos_vio1_isp_r: qos@ffad0900 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffad0900 0x0 0x20>; |
| }; |
| |
| qos_video: qos@ffae0000 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffae0000 0x0 0x20>; |
| }; |
| |
| qos_hevc_r: qos@ffaf0000 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffaf0000 0x0 0x20>; |
| }; |
| |
| qos_hevc_w: qos@ffaf0080 { |
| compatible = "rockchip,rk3288-qos", "syscon"; |
| reg = <0x0 0xffaf0080 0x0 0x20>; |
| }; |
| |
| dmac_bus_s: dma-controller@ffb20000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x0 0xffb20000 0x0 0x4000>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| arm,pl330-broken-no-flushp; |
| arm,pl330-periph-burst; |
| clocks = <&cru ACLK_DMAC1>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| efuse: efuse@ffb40000 { |
| compatible = "rockchip,rk3288-efuse"; |
| reg = <0x0 0xffb40000 0x0 0x20>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| clocks = <&cru PCLK_EFUSE256>; |
| clock-names = "pclk_efuse"; |
| |
| cpu_id: cpu-id@7 { |
| reg = <0x07 0x10>; |
| }; |
| cpu_leakage: cpu_leakage@17 { |
| reg = <0x17 0x1>; |
| }; |
| }; |
| |
| gic: interrupt-controller@ffc01000 { |
| compatible = "arm,gic-400"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| |
| reg = <0x0 0xffc01000 0x0 0x1000>, |
| <0x0 0xffc02000 0x0 0x2000>, |
| <0x0 0xffc04000 0x0 0x2000>, |
| <0x0 0xffc06000 0x0 0x2000>; |
| interrupts = <GIC_PPI 9 0xf04>; |
| }; |
| |
| pinctrl: pinctrl { |
| compatible = "rockchip,rk3288-pinctrl"; |
| rockchip,grf = <&grf>; |
| rockchip,pmu = <&pmu>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| gpio0: gpio@ff750000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff750000 0x0 0x100>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio@ff780000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff780000 0x0 0x100>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO1>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@ff790000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff790000 0x0 0x100>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO2>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@ff7a0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7a0000 0x0 0x100>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO3>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@ff7b0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7b0000 0x0 0x100>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO4>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@ff7c0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7c0000 0x0 0x100>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO5>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@ff7d0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7d0000 0x0 0x100>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO6>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio7: gpio@ff7e0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7e0000 0x0 0x100>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO7>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio8: gpio@ff7f0000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x0 0xff7f0000 0x0 0x100>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO8>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| hdmi { |
| hdmi_cec_c0: hdmi-cec-c0 { |
| rockchip,pins = <7 RK_PC0 2 &pcfg_pull_none>; |
| }; |
| |
| hdmi_cec_c7: hdmi-cec-c7 { |
| rockchip,pins = <7 RK_PC7 4 &pcfg_pull_none>; |
| }; |
| |
| hdmi_ddc: hdmi-ddc { |
| rockchip,pins = <7 RK_PC3 2 &pcfg_pull_none>, |
| <7 RK_PC4 2 &pcfg_pull_none>; |
| }; |
| |
| hdmi_ddc_unwedge: hdmi-ddc-unwedge { |
| rockchip,pins = <7 RK_PC3 RK_FUNC_GPIO &pcfg_output_low>, |
| <7 RK_PC4 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pcfg_output_low: pcfg-output-low { |
| output-low; |
| }; |
| |
| pcfg_pull_up: pcfg-pull-up { |
| bias-pull-up; |
| }; |
| |
| pcfg_pull_down: pcfg-pull-down { |
| bias-pull-down; |
| }; |
| |
| pcfg_pull_none: pcfg-pull-none { |
| bias-disable; |
| }; |
| |
| pcfg_pull_none_12ma: pcfg-pull-none-12ma { |
| bias-disable; |
| drive-strength = <12>; |
| }; |
| |
| suspend { |
| global_pwroff: global-pwroff { |
| rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>; |
| }; |
| |
| ddrio_pwroff: ddrio-pwroff { |
| rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>; |
| }; |
| |
| ddr0_retention: ddr0-retention { |
| rockchip,pins = <0 RK_PA2 1 &pcfg_pull_up>; |
| }; |
| |
| ddr1_retention: ddr1-retention { |
| rockchip,pins = <0 RK_PA3 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| edp { |
| edp_hpd: edp-hpd { |
| rockchip,pins = <7 RK_PB3 2 &pcfg_pull_down>; |
| }; |
| }; |
| |
| i2c0 { |
| i2c0_xfer: i2c0-xfer { |
| rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>, |
| <0 RK_PC0 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c1 { |
| i2c1_xfer: i2c1-xfer { |
| rockchip,pins = <8 RK_PA4 1 &pcfg_pull_none>, |
| <8 RK_PA5 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c2 { |
| i2c2_xfer: i2c2-xfer { |
| rockchip,pins = <6 RK_PB1 1 &pcfg_pull_none>, |
| <6 RK_PB2 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c3 { |
| i2c3_xfer: i2c3-xfer { |
| rockchip,pins = <2 RK_PC0 1 &pcfg_pull_none>, |
| <2 RK_PC1 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c4 { |
| i2c4_xfer: i2c4-xfer { |
| rockchip,pins = <7 RK_PC1 1 &pcfg_pull_none>, |
| <7 RK_PC2 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c5 { |
| i2c5_xfer: i2c5-xfer { |
| rockchip,pins = <7 RK_PC3 1 &pcfg_pull_none>, |
| <7 RK_PC4 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2s0 { |
| i2s0_bus: i2s0-bus { |
| rockchip,pins = <6 RK_PA0 1 &pcfg_pull_none>, |
| <6 RK_PA1 1 &pcfg_pull_none>, |
| <6 RK_PA2 1 &pcfg_pull_none>, |
| <6 RK_PA3 1 &pcfg_pull_none>, |
| <6 RK_PA4 1 &pcfg_pull_none>, |
| <6 RK_PB0 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| lcdc { |
| lcdc_ctl: lcdc-ctl { |
| rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>, |
| <1 RK_PD1 1 &pcfg_pull_none>, |
| <1 RK_PD2 1 &pcfg_pull_none>, |
| <1 RK_PD3 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| sdmmc { |
| sdmmc_clk: sdmmc-clk { |
| rockchip,pins = <6 RK_PC4 1 &pcfg_pull_none>; |
| }; |
| |
| sdmmc_cmd: sdmmc-cmd { |
| rockchip,pins = <6 RK_PC5 1 &pcfg_pull_up>; |
| }; |
| |
| sdmmc_cd: sdmmc-cd { |
| rockchip,pins = <6 RK_PC6 1 &pcfg_pull_up>; |
| }; |
| |
| sdmmc_bus1: sdmmc-bus1 { |
| rockchip,pins = <6 RK_PC0 1 &pcfg_pull_up>; |
| }; |
| |
| sdmmc_bus4: sdmmc-bus4 { |
| rockchip,pins = <6 RK_PC0 1 &pcfg_pull_up>, |
| <6 RK_PC1 1 &pcfg_pull_up>, |
| <6 RK_PC2 1 &pcfg_pull_up>, |
| <6 RK_PC3 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| sdio0 { |
| sdio0_bus1: sdio0-bus1 { |
| rockchip,pins = <4 RK_PC4 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_bus4: sdio0-bus4 { |
| rockchip,pins = <4 RK_PC4 1 &pcfg_pull_up>, |
| <4 RK_PC5 1 &pcfg_pull_up>, |
| <4 RK_PC6 1 &pcfg_pull_up>, |
| <4 RK_PC7 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_cmd: sdio0-cmd { |
| rockchip,pins = <4 RK_PD0 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_clk: sdio0-clk { |
| rockchip,pins = <4 RK_PD1 1 &pcfg_pull_none>; |
| }; |
| |
| sdio0_cd: sdio0-cd { |
| rockchip,pins = <4 RK_PD2 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_wp: sdio0-wp { |
| rockchip,pins = <4 RK_PD3 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_pwr: sdio0-pwr { |
| rockchip,pins = <4 RK_PD4 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_bkpwr: sdio0-bkpwr { |
| rockchip,pins = <4 RK_PD5 1 &pcfg_pull_up>; |
| }; |
| |
| sdio0_int: sdio0-int { |
| rockchip,pins = <4 RK_PD6 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| sdio1 { |
| sdio1_bus1: sdio1-bus1 { |
| rockchip,pins = <3 RK_PD0 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_bus4: sdio1-bus4 { |
| rockchip,pins = <3 RK_PD0 4 &pcfg_pull_up>, |
| <3 RK_PD1 4 &pcfg_pull_up>, |
| <3 RK_PD2 4 &pcfg_pull_up>, |
| <3 RK_PD3 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_cd: sdio1-cd { |
| rockchip,pins = <3 RK_PD4 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_wp: sdio1-wp { |
| rockchip,pins = <3 RK_PD5 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_bkpwr: sdio1-bkpwr { |
| rockchip,pins = <3 RK_PD6 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_int: sdio1-int { |
| rockchip,pins = <3 RK_PD7 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_cmd: sdio1-cmd { |
| rockchip,pins = <4 RK_PA6 4 &pcfg_pull_up>; |
| }; |
| |
| sdio1_clk: sdio1-clk { |
| rockchip,pins = <4 RK_PA7 4 &pcfg_pull_none>; |
| }; |
| |
| sdio1_pwr: sdio1-pwr { |
| rockchip,pins = <4 RK_PB1 4 &pcfg_pull_up>; |
| }; |
| }; |
| |
| emmc { |
| emmc_clk: emmc-clk { |
| rockchip,pins = <3 RK_PC2 2 &pcfg_pull_none>; |
| }; |
| |
| emmc_cmd: emmc-cmd { |
| rockchip,pins = <3 RK_PC0 2 &pcfg_pull_up>; |
| }; |
| |
| emmc_pwr: emmc-pwr { |
| rockchip,pins = <3 RK_PB1 2 &pcfg_pull_up>; |
| }; |
| |
| emmc_bus1: emmc-bus1 { |
| rockchip,pins = <3 RK_PA0 2 &pcfg_pull_up>; |
| }; |
| |
| emmc_bus4: emmc-bus4 { |
| rockchip,pins = <3 RK_PA0 2 &pcfg_pull_up>, |
| <3 RK_PA1 2 &pcfg_pull_up>, |
| <3 RK_PA2 2 &pcfg_pull_up>, |
| <3 RK_PA3 2 &pcfg_pull_up>; |
| }; |
| |
| emmc_bus8: emmc-bus8 { |
| rockchip,pins = <3 RK_PA0 2 &pcfg_pull_up>, |
| <3 RK_PA1 2 &pcfg_pull_up>, |
| <3 RK_PA2 2 &pcfg_pull_up>, |
| <3 RK_PA3 2 &pcfg_pull_up>, |
| <3 RK_PA4 2 &pcfg_pull_up>, |
| <3 RK_PA5 2 &pcfg_pull_up>, |
| <3 RK_PA6 2 &pcfg_pull_up>, |
| <3 RK_PA7 2 &pcfg_pull_up>; |
| }; |
| }; |
| |
| spi0 { |
| spi0_clk: spi0-clk { |
| rockchip,pins = <5 RK_PB4 1 &pcfg_pull_up>; |
| }; |
| spi0_cs0: spi0-cs0 { |
| rockchip,pins = <5 RK_PB5 1 &pcfg_pull_up>; |
| }; |
| spi0_tx: spi0-tx { |
| rockchip,pins = <5 RK_PB6 1 &pcfg_pull_up>; |
| }; |
| spi0_rx: spi0-rx { |
| rockchip,pins = <5 RK_PB7 1 &pcfg_pull_up>; |
| }; |
| spi0_cs1: spi0-cs1 { |
| rockchip,pins = <5 RK_PC0 1 &pcfg_pull_up>; |
| }; |
| }; |
| spi1 { |
| spi1_clk: spi1-clk { |
| rockchip,pins = <7 RK_PB4 2 &pcfg_pull_up>; |
| }; |
| spi1_cs0: spi1-cs0 { |
| rockchip,pins = <7 RK_PB5 2 &pcfg_pull_up>; |
| }; |
| spi1_rx: spi1-rx { |
| rockchip,pins = <7 RK_PB6 2 &pcfg_pull_up>; |
| }; |
| spi1_tx: spi1-tx { |
| rockchip,pins = <7 RK_PB7 2 &pcfg_pull_up>; |
| }; |
| }; |
| |
| spi2 { |
| spi2_cs1: spi2-cs1 { |
| rockchip,pins = <8 RK_PA3 1 &pcfg_pull_up>; |
| }; |
| spi2_clk: spi2-clk { |
| rockchip,pins = <8 RK_PA6 1 &pcfg_pull_up>; |
| }; |
| spi2_cs0: spi2-cs0 { |
| rockchip,pins = <8 RK_PA7 1 &pcfg_pull_up>; |
| }; |
| spi2_rx: spi2-rx { |
| rockchip,pins = <8 RK_PB0 1 &pcfg_pull_up>; |
| }; |
| spi2_tx: spi2-tx { |
| rockchip,pins = <8 RK_PB1 1 &pcfg_pull_up>; |
| }; |
| }; |
| |
| uart0 { |
| uart0_xfer: uart0-xfer { |
| rockchip,pins = <4 RK_PC0 1 &pcfg_pull_up>, |
| <4 RK_PC1 1 &pcfg_pull_none>; |
| }; |
| |
| uart0_cts: uart0-cts { |
| rockchip,pins = <4 RK_PC2 1 &pcfg_pull_up>; |
| }; |
| |
| uart0_rts: uart0-rts { |
| rockchip,pins = <4 RK_PC3 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart1 { |
| uart1_xfer: uart1-xfer { |
| rockchip,pins = <5 RK_PB0 1 &pcfg_pull_up>, |
| <5 RK_PB1 1 &pcfg_pull_none>; |
| }; |
| |
| uart1_cts: uart1-cts { |
| rockchip,pins = <5 RK_PB2 1 &pcfg_pull_up>; |
| }; |
| |
| uart1_rts: uart1-rts { |
| rockchip,pins = <5 RK_PB3 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart2 { |
| uart2_xfer: uart2-xfer { |
| rockchip,pins = <7 RK_PC6 1 &pcfg_pull_up>, |
| <7 RK_PC7 1 &pcfg_pull_none>; |
| }; |
| /* no rts / cts for uart2 */ |
| }; |
| |
| uart3 { |
| uart3_xfer: uart3-xfer { |
| rockchip,pins = <7 RK_PA7 1 &pcfg_pull_up>, |
| <7 RK_PB0 1 &pcfg_pull_none>; |
| }; |
| |
| uart3_cts: uart3-cts { |
| rockchip,pins = <7 RK_PB1 1 &pcfg_pull_up>; |
| }; |
| |
| uart3_rts: uart3-rts { |
| rockchip,pins = <7 RK_PB2 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart4 { |
| uart4_xfer: uart4-xfer { |
| rockchip,pins = <5 RK_PB7 3 &pcfg_pull_up>, |
| <5 RK_PB6 3 &pcfg_pull_none>; |
| }; |
| |
| uart4_cts: uart4-cts { |
| rockchip,pins = <5 RK_PB4 3 &pcfg_pull_up>; |
| }; |
| |
| uart4_rts: uart4-rts { |
| rockchip,pins = <5 RK_PB5 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| tsadc { |
| otp_pin: otp-pin { |
| rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| otp_out: otp-out { |
| rockchip,pins = <0 RK_PB2 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm0 { |
| pwm0_pin: pwm0-pin { |
| rockchip,pins = <7 RK_PA0 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm1 { |
| pwm1_pin: pwm1-pin { |
| rockchip,pins = <7 RK_PA1 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm2 { |
| pwm2_pin: pwm2-pin { |
| rockchip,pins = <7 RK_PC6 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm3 { |
| pwm3_pin: pwm3-pin { |
| rockchip,pins = <7 RK_PC7 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| gmac { |
| rgmii_pins: rgmii-pins { |
| rockchip,pins = <3 RK_PD6 3 &pcfg_pull_none>, |
| <3 RK_PD7 3 &pcfg_pull_none>, |
| <3 RK_PD2 3 &pcfg_pull_none>, |
| <3 RK_PD3 3 &pcfg_pull_none>, |
| <3 RK_PD4 3 &pcfg_pull_none_12ma>, |
| <3 RK_PD5 3 &pcfg_pull_none_12ma>, |
| <3 RK_PD0 3 &pcfg_pull_none_12ma>, |
| <3 RK_PD1 3 &pcfg_pull_none_12ma>, |
| <4 RK_PA0 3 &pcfg_pull_none>, |
| <4 RK_PA5 3 &pcfg_pull_none>, |
| <4 RK_PA6 3 &pcfg_pull_none>, |
| <4 RK_PB1 3 &pcfg_pull_none_12ma>, |
| <4 RK_PA4 3 &pcfg_pull_none_12ma>, |
| <4 RK_PA1 3 &pcfg_pull_none>, |
| <4 RK_PA3 3 &pcfg_pull_none>; |
| }; |
| |
| rmii_pins: rmii-pins { |
| rockchip,pins = <3 RK_PD6 3 &pcfg_pull_none>, |
| <3 RK_PD7 3 &pcfg_pull_none>, |
| <3 RK_PD4 3 &pcfg_pull_none>, |
| <3 RK_PD5 3 &pcfg_pull_none>, |
| <4 RK_PA0 3 &pcfg_pull_none>, |
| <4 RK_PA5 3 &pcfg_pull_none>, |
| <4 RK_PA4 3 &pcfg_pull_none>, |
| <4 RK_PA1 3 &pcfg_pull_none>, |
| <4 RK_PA2 3 &pcfg_pull_none>, |
| <4 RK_PA3 3 &pcfg_pull_none>; |
| }; |
| }; |
| |
| spdif { |
| spdif_tx: spdif-tx { |
| rockchip,pins = <6 RK_PB3 1 &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| }; |
