blob: 40414247d61a35d1f85d60473b131e9cbe147222 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
maintainers:
- Fabio Estevam <festevam@gmail.com>
allOf:
- $ref: serial.yaml#
- $ref: rs485.yaml#
properties:
compatible:
oneOf:
- const: fsl,imx1-uart
- const: fsl,imx21-uart
- items:
- enum:
- fsl,imx25-uart
- fsl,imx27-uart
- fsl,imx31-uart
- fsl,imx35-uart
- fsl,imx50-uart
- fsl,imx51-uart
- fsl,imx53-uart
- fsl,imx6q-uart
- const: fsl,imx21-uart
- items:
- enum:
- fsl,imx6sl-uart
- fsl,imx6sll-uart
- fsl,imx6sx-uart
- const: fsl,imx6q-uart
- const: fsl,imx21-uart
- items:
- enum:
- fsl,imx6ul-uart
- fsl,imx7d-uart
- fsl,imx8mm-uart
- fsl,imx8mn-uart
- fsl,imx8mp-uart
- fsl,imx8mq-uart
- const: fsl,imx6q-uart
reg:
maxItems: 1
clocks:
maxItems: 2
clock-names:
items:
- const: ipg
- const: per
dmas:
items:
- description: DMA controller phandle and request line for RX
- description: DMA controller phandle and request line for TX
dma-names:
items:
- const: rx
- const: tx
interrupts:
maxItems: 1
fsl,dte-mode:
$ref: /schemas/types.yaml#/definitions/flag
description: |
Indicate the uart works in DTE mode. The uart works in DCE mode by default.
fsl,inverted-tx:
$ref: /schemas/types.yaml#/definitions/flag
description: |
Indicate that the hardware attached to the peripheral inverts the signal
transmitted, and that the peripheral should invert its output using the
INVT registers.
fsl,inverted-rx:
$ref: /schemas/types.yaml#/definitions/flag
description: |
Indicate that the hardware attached to the peripheral inverts the signal
received, and that the peripheral should invert its input using the
INVR registers.
fsl,dma-info:
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 2
maxItems: 2
description: |
First cell contains the size of DMA buffer chunks, second cell contains
the amount of chunks used for the device. Multiplying both numbers is
the total size of memory used for receiving data.
When not being configured the system will use default settings, which
are sensible for most use cases. If you need low latency processing on
slow connections this needs to be configured appropriately.
required:
- compatible
- reg
- clocks
- clock-names
- interrupts
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/imx5-clock.h>
aliases {
serial0 = &uart1;
};
uart1: serial@73fbc000 {
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x73fbc000 0x4000>;
interrupts = <31>;
clocks = <&clks IMX5_CLK_UART1_IPG_GATE>,
<&clks IMX5_CLK_UART1_PER_GATE>;
clock-names = "ipg", "per";
dmas = <&sdma 18 4 1>, <&sdma 19 4 2>;
dma-names = "rx", "tx";
uart-has-rtscts;
fsl,dte-mode;
};