| /* |
| * Copyright (C) 2010,2011 Google, Inc. |
| * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved. |
| * |
| * Author: |
| * Colin Cross <ccross@google.com> |
| * Erik Gilling <konkers@google.com> |
| * Doug Anderson <dianders@chromium.org> |
| * Stephen Warren <swarren@nvidia.com> |
| * |
| * Portions based on mach-omap2's debug-macro.S |
| * Copyright (C) 1994-1999 Russell King |
| * |
| * This software is licensed under the terms of the GNU General Public |
| * License version 2, as published by the Free Software Foundation, and |
| * may be copied, distributed, and modified under those terms. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| |
| #include <linux/serial_reg.h> |
| |
| #define UART_SHIFT 2 |
| |
| /* Physical addresses */ |
| #define TEGRA_CLK_RESET_BASE 0x60006000 |
| #define TEGRA_APB_MISC_BASE 0x70000000 |
| #define TEGRA_UARTA_BASE 0x70006000 |
| #define TEGRA_UARTB_BASE 0x70006040 |
| #define TEGRA_UARTC_BASE 0x70006200 |
| #define TEGRA_UARTD_BASE 0x70006300 |
| #define TEGRA_UARTE_BASE 0x70006400 |
| #define TEGRA_PMC_BASE 0x7000e400 |
| |
| #define TEGRA_CLK_RST_DEVICES_L (TEGRA_CLK_RESET_BASE + 0x04) |
| #define TEGRA_CLK_RST_DEVICES_H (TEGRA_CLK_RESET_BASE + 0x08) |
| #define TEGRA_CLK_RST_DEVICES_U (TEGRA_CLK_RESET_BASE + 0x0c) |
| #define TEGRA_CLK_OUT_ENB_L (TEGRA_CLK_RESET_BASE + 0x10) |
| #define TEGRA_CLK_OUT_ENB_H (TEGRA_CLK_RESET_BASE + 0x14) |
| #define TEGRA_CLK_OUT_ENB_U (TEGRA_CLK_RESET_BASE + 0x18) |
| #define TEGRA_PMC_SCRATCH20 (TEGRA_PMC_BASE + 0xa0) |
| #define TEGRA_APB_MISC_GP_HIDREV (TEGRA_APB_MISC_BASE + 0x804) |
| |
| /* |
| * Must be section-aligned since a section mapping is used early on. |
| * Must not overlap with regions in mach-tegra/io.c:tegra_io_desc[]. |
| */ |
| #define UART_VIRTUAL_BASE 0xfe800000 |
| |
| #define checkuart(rp, rv, lhu, bit, uart) \ |
| /* Load address of CLK_RST register */ \ |
| ldr rp, =TEGRA_CLK_RST_DEVICES_##lhu ; \ |
| /* Load value from CLK_RST register */ \ |
| ldr rp, [rp, #0] ; \ |
| /* Test UART's reset bit */ \ |
| tst rp, #(1 << bit) ; \ |
| /* If set, can't use UART; jump to save no UART */ \ |
| bne 90f ; \ |
| /* Load address of CLK_OUT_ENB register */ \ |
| ldr rp, =TEGRA_CLK_OUT_ENB_##lhu ; \ |
| /* Load value from CLK_OUT_ENB register */ \ |
| ldr rp, [rp, #0] ; \ |
| /* Test UART's clock enable bit */ \ |
| tst rp, #(1 << bit) ; \ |
| /* If clear, can't use UART; jump to save no UART */ \ |
| beq 90f ; \ |
| /* Passed all tests, load address of UART registers */ \ |
| ldr rp, =TEGRA_UART##uart##_BASE ; \ |
| /* Jump to save UART address */ \ |
| b 91f |
| |
| .macro addruart, rp, rv, tmp |
| adr \rp, 99f @ actual addr of 99f |
| ldr \rv, [\rp] @ linked addr is stored there |
| sub \rv, \rv, \rp @ offset between the two |
| ldr \rp, [\rp, #4] @ linked tegra_uart_config |
| sub \tmp, \rp, \rv @ actual tegra_uart_config |
| ldr \rp, [\tmp] @ Load tegra_uart_config |
| cmp \rp, #1 @ needs initialization? |
| bne 100f @ no; go load the addresses |
| mov \rv, #0 @ yes; record init is done |
| str \rv, [\tmp] |
| |
| #ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA |
| /* Check ODMDATA */ |
| 10: ldr \rp, =TEGRA_PMC_SCRATCH20 |
| ldr \rp, [\rp, #0] @ Load PMC_SCRATCH20 |
| lsr \rv, \rp, #18 @ 19:18 are console type |
| and \rv, \rv, #3 |
| cmp \rv, #2 @ 2 and 3 mean DCC, UART |
| beq 11f @ some boards swap the meaning |
| cmp \rv, #3 @ so accept either |
| bne 90f |
| 11: lsr \rv, \rp, #15 @ 17:15 are UART ID |
| and \rv, #7 |
| cmp \rv, #0 @ UART 0? |
| beq 20f |
| cmp \rv, #1 @ UART 1? |
| beq 21f |
| cmp \rv, #2 @ UART 2? |
| beq 22f |
| cmp \rv, #3 @ UART 3? |
| beq 23f |
| cmp \rv, #4 @ UART 4? |
| beq 24f |
| b 90f @ invalid |
| #endif |
| |
| #if defined(CONFIG_TEGRA_DEBUG_UARTA) || \ |
| defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA) |
| /* Check UART A validity */ |
| 20: checkuart(\rp, \rv, L, 6, A) |
| #endif |
| |
| #if defined(CONFIG_TEGRA_DEBUG_UARTB) || \ |
| defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA) |
| /* Check UART B validity */ |
| 21: checkuart(\rp, \rv, L, 7, B) |
| #endif |
| |
| #if defined(CONFIG_TEGRA_DEBUG_UARTC) || \ |
| defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA) |
| /* Check UART C validity */ |
| 22: checkuart(\rp, \rv, H, 23, C) |
| #endif |
| |
| #if defined(CONFIG_TEGRA_DEBUG_UARTD) || \ |
| defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA) |
| /* Check UART D validity */ |
| 23: checkuart(\rp, \rv, U, 1, D) |
| #endif |
| |
| #if defined(CONFIG_TEGRA_DEBUG_UARTE) || \ |
| defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA) |
| /* Check UART E validity */ |
| 24: |
| checkuart(\rp, \rv, U, 2, E) |
| #endif |
| |
| /* No valid UART found */ |
| 90: mov \rp, #0 |
| /* fall through */ |
| |
| /* Record whichever UART we chose */ |
| 91: str \rp, [\tmp, #4] @ Store in tegra_uart_phys |
| cmp \rp, #0 @ Valid UART address? |
| bne 92f @ Yes, go process it |
| str \rp, [\tmp, #8] @ Store 0 in tegra_uart_virt |
| b 100f @ Done |
| 92: and \rv, \rp, #0xffffff @ offset within 1MB section |
| add \rv, \rv, #UART_VIRTUAL_BASE |
| str \rv, [\tmp, #8] @ Store in tegra_uart_virt |
| b 100f |
| |
| .align |
| 99: .word . |
| .word tegra_uart_config |
| .ltorg |
| |
| /* Load previously selected UART address */ |
| 100: ldr \rp, [\tmp, #4] @ Load tegra_uart_phys |
| ldr \rv, [\tmp, #8] @ Load tegra_uart_virt |
| .endm |
| |
| /* |
| * Code below is swiped from <asm/hardware/debug-8250.S>, but add an extra |
| * check to make sure that the UART address is actually valid. |
| */ |
| |
| .macro senduart, rd, rx |
| cmp \rx, #0 |
| strbne \rd, [\rx, #UART_TX << UART_SHIFT] |
| 1001: |
| .endm |
| |
| .macro busyuart, rd, rx |
| cmp \rx, #0 |
| beq 1002f |
| 1001: ldrb \rd, [\rx, #UART_LSR << UART_SHIFT] |
| and \rd, \rd, #UART_LSR_THRE |
| teq \rd, #UART_LSR_THRE |
| bne 1001b |
| 1002: |
| .endm |
| |
| .macro waituart, rd, rx |
| #ifdef FLOW_CONTROL |
| cmp \rx, #0 |
| beq 1002f |
| 1001: ldrb \rd, [\rx, #UART_MSR << UART_SHIFT] |
| tst \rd, #UART_MSR_CTS |
| beq 1001b |
| 1002: |
| #endif |
| .endm |
| |
| /* |
| * Storage for the state maintained by the macros above. |
| * |
| * In the kernel proper, this data is located in arch/arm/mach-tegra/tegra.c. |
| * That's because this header is included from multiple files, and we only |
| * want a single copy of the data. In particular, the UART probing code above |
| * assumes it's running using physical addresses. This is true when this file |
| * is included from head.o, but not when included from debug.o. So we need |
| * to share the probe results between the two copies, rather than having |
| * to re-run the probing again later. |
| * |
| * In the decompressor, we put the symbol/storage right here, since common.c |
| * isn't included in the decompressor build. This symbol gets put in .text |
| * even though it's really data, since .data is discarded from the |
| * decompressor. Luckily, .text is writeable in the decompressor, unless |
| * CONFIG_ZBOOT_ROM. That dependency is handled in arch/arm/Kconfig.debug. |
| */ |
| #if defined(ZIMAGE) |
| tegra_uart_config: |
| /* Debug UART initialization required */ |
| .word 1 |
| /* Debug UART physical address */ |
| .word 0 |
| /* Debug UART virtual address */ |
| .word 0 |
| #endif |