| # SPDX-License-Identifier: GPL-2.0-only |
| # The IOVA library may also be used by non-IOMMU_API users |
| config IOMMU_IOVA |
| tristate |
| |
| # The IOASID library may also be used by non-IOMMU_API users |
| config IOASID |
| tristate |
| |
| # IOMMU_API always gets selected by whoever wants it. |
| config IOMMU_API |
| bool |
| |
| menuconfig IOMMU_SUPPORT |
| bool "IOMMU Hardware Support" |
| depends on MMU |
| default y |
| ---help--- |
| Say Y here if you want to compile device drivers for IO Memory |
| Management Units into the kernel. These devices usually allow to |
| remap DMA requests and/or remap interrupts from other devices on the |
| system. |
| |
| if IOMMU_SUPPORT |
| |
| menu "Generic IOMMU Pagetable Support" |
| |
| # Selected by the actual pagetable implementations |
| config IOMMU_IO_PGTABLE |
| bool |
| |
| config IOMMU_IO_PGTABLE_LPAE |
| bool "ARMv7/v8 Long Descriptor Format" |
| select IOMMU_IO_PGTABLE |
| depends on ARM || ARM64 || (COMPILE_TEST && !GENERIC_ATOMIC64) |
| help |
| Enable support for the ARM long descriptor pagetable format. |
| This allocator supports 4K/2M/1G, 16K/32M and 64K/512M page |
| sizes at both stage-1 and stage-2, as well as address spaces |
| up to 48-bits in size. |
| |
| config IOMMU_IO_PGTABLE_LPAE_SELFTEST |
| bool "LPAE selftests" |
| depends on IOMMU_IO_PGTABLE_LPAE |
| help |
| Enable self-tests for LPAE page table allocator. This performs |
| a series of page-table consistency checks during boot. |
| |
| If unsure, say N here. |
| |
| config IOMMU_IO_PGTABLE_ARMV7S |
| bool "ARMv7/v8 Short Descriptor Format" |
| select IOMMU_IO_PGTABLE |
| depends on ARM || ARM64 || COMPILE_TEST |
| help |
| Enable support for the ARM Short-descriptor pagetable format. |
| This supports 32-bit virtual and physical addresses mapped using |
| 2-level tables with 4KB pages/1MB sections, and contiguous entries |
| for 64KB pages/16MB supersections if indicated by the IOMMU driver. |
| |
| config IOMMU_IO_PGTABLE_ARMV7S_SELFTEST |
| bool "ARMv7s selftests" |
| depends on IOMMU_IO_PGTABLE_ARMV7S |
| help |
| Enable self-tests for ARMv7s page table allocator. This performs |
| a series of page-table consistency checks during boot. |
| |
| If unsure, say N here. |
| |
| endmenu |
| |
| config IOMMU_DEBUGFS |
| bool "Export IOMMU internals in DebugFS" |
| depends on DEBUG_FS |
| help |
| Allows exposure of IOMMU device internals. This option enables |
| the use of debugfs by IOMMU drivers as required. Devices can, |
| at initialization time, cause the IOMMU code to create a top-level |
| debug/iommu directory, and then populate a subdirectory with |
| entries as required. |
| |
| config IOMMU_DEFAULT_PASSTHROUGH |
| bool "IOMMU passthrough by default" |
| depends on IOMMU_API |
| help |
| Enable passthrough by default, removing the need to pass in |
| iommu.passthrough=on or iommu=pt through command line. If this |
| is enabled, you can still disable with iommu.passthrough=off |
| or iommu=nopt depending on the architecture. |
| |
| If unsure, say N here. |
| |
| config OF_IOMMU |
| def_bool y |
| depends on OF && IOMMU_API |
| |
| # IOMMU-agnostic DMA-mapping layer |
| config IOMMU_DMA |
| bool |
| select IOMMU_API |
| select IOMMU_IOVA |
| select IRQ_MSI_IOMMU |
| select NEED_SG_DMA_LENGTH |
| |
| config FSL_PAMU |
| bool "Freescale IOMMU support" |
| depends on PCI |
| depends on PHYS_64BIT |
| depends on PPC_E500MC || (COMPILE_TEST && PPC) |
| select IOMMU_API |
| select GENERIC_ALLOCATOR |
| help |
| Freescale PAMU support. PAMU is the IOMMU present on Freescale QorIQ platforms. |
| PAMU can authorize memory access, remap the memory address, and remap I/O |
| transaction types. |
| |
| # MSM IOMMU support |
| config MSM_IOMMU |
| bool "MSM IOMMU Support" |
| depends on ARM |
| depends on ARCH_MSM8X60 || ARCH_MSM8960 || COMPILE_TEST |
| select IOMMU_API |
| select IOMMU_IO_PGTABLE_ARMV7S |
| help |
| Support for the IOMMUs found on certain Qualcomm SOCs. |
| These IOMMUs allow virtualization of the address space used by most |
| cores within the multimedia subsystem. |
| |
| If unsure, say N here. |
| |
| config IOMMU_PGTABLES_L2 |
| def_bool y |
| depends on MSM_IOMMU && MMU && SMP && CPU_DCACHE_DISABLE=n |
| |
| # AMD IOMMU support |
| config AMD_IOMMU |
| bool "AMD IOMMU support" |
| select SWIOTLB |
| select PCI_MSI |
| select PCI_ATS |
| select PCI_PRI |
| select PCI_PASID |
| select IOMMU_API |
| select IOMMU_IOVA |
| select IOMMU_DMA |
| depends on X86_64 && PCI && ACPI |
| ---help--- |
| With this option you can enable support for AMD IOMMU hardware in |
| your system. An IOMMU is a hardware component which provides |
| remapping of DMA memory accesses from devices. With an AMD IOMMU you |
| can isolate the DMA memory of different devices and protect the |
| system from misbehaving device drivers or hardware. |
| |
| You can find out if your system has an AMD IOMMU if you look into |
| your BIOS for an option to enable it or if you have an IVRS ACPI |
| table. |
| |
| config AMD_IOMMU_V2 |
| tristate "AMD IOMMU Version 2 driver" |
| depends on AMD_IOMMU |
| select MMU_NOTIFIER |
| ---help--- |
| This option enables support for the AMD IOMMUv2 features of the IOMMU |
| hardware. Select this option if you want to use devices that support |
| the PCI PRI and PASID interface. |
| |
| config AMD_IOMMU_DEBUGFS |
| bool "Enable AMD IOMMU internals in DebugFS" |
| depends on AMD_IOMMU && IOMMU_DEBUGFS |
| ---help--- |
| !!!WARNING!!! !!!WARNING!!! !!!WARNING!!! !!!WARNING!!! |
| |
| DO NOT ENABLE THIS OPTION UNLESS YOU REALLY, -REALLY- KNOW WHAT YOU ARE DOING!!! |
| Exposes AMD IOMMU device internals in DebugFS. |
| |
| This option is -NOT- intended for production environments, and should |
| not generally be enabled. |
| |
| # Intel IOMMU support |
| config DMAR_TABLE |
| bool |
| |
| config INTEL_IOMMU |
| bool "Support for Intel IOMMU using DMA Remapping Devices" |
| depends on PCI_MSI && ACPI && (X86 || IA64) |
| select IOMMU_API |
| select IOMMU_IOVA |
| select NEED_DMA_MAP_STATE |
| select DMAR_TABLE |
| select SWIOTLB |
| help |
| DMA remapping (DMAR) devices support enables independent address |
| translations for Direct Memory Access (DMA) from devices. |
| These DMA remapping devices are reported via ACPI tables |
| and include PCI device scope covered by these DMA |
| remapping devices. |
| |
| config INTEL_IOMMU_DEBUGFS |
| bool "Export Intel IOMMU internals in Debugfs" |
| depends on INTEL_IOMMU && IOMMU_DEBUGFS |
| help |
| !!!WARNING!!! |
| |
| DO NOT ENABLE THIS OPTION UNLESS YOU REALLY KNOW WHAT YOU ARE DOING!!! |
| |
| Expose Intel IOMMU internals in Debugfs. |
| |
| This option is -NOT- intended for production environments, and should |
| only be enabled for debugging Intel IOMMU. |
| |
| config INTEL_IOMMU_SVM |
| bool "Support for Shared Virtual Memory with Intel IOMMU" |
| depends on INTEL_IOMMU && X86 |
| select PCI_PASID |
| select PCI_PRI |
| select MMU_NOTIFIER |
| help |
| Shared Virtual Memory (SVM) provides a facility for devices |
| to access DMA resources through process address space by |
| means of a Process Address Space ID (PASID). |
| |
| config INTEL_IOMMU_DEFAULT_ON |
| def_bool y |
| prompt "Enable Intel DMA Remapping Devices by default" |
| depends on INTEL_IOMMU |
| help |
| Selecting this option will enable a DMAR device at boot time if |
| one is found. If this option is not selected, DMAR support can |
| be enabled by passing intel_iommu=on to the kernel. |
| |
| config INTEL_IOMMU_BROKEN_GFX_WA |
| bool "Workaround broken graphics drivers (going away soon)" |
| depends on INTEL_IOMMU && BROKEN && X86 |
| ---help--- |
| Current Graphics drivers tend to use physical address |
| for DMA and avoid using DMA APIs. Setting this config |
| option permits the IOMMU driver to set a unity map for |
| all the OS-visible memory. Hence the driver can continue |
| to use physical addresses for DMA, at least until this |
| option is removed in the 2.6.32 kernel. |
| |
| config INTEL_IOMMU_FLOPPY_WA |
| def_bool y |
| depends on INTEL_IOMMU && X86 |
| ---help--- |
| Floppy disk drivers are known to bypass DMA API calls |
| thereby failing to work when IOMMU is enabled. This |
| workaround will setup a 1:1 mapping for the first |
| 16MiB to make floppy (an ISA device) work. |
| |
| config IRQ_REMAP |
| bool "Support for Interrupt Remapping" |
| depends on X86_64 && X86_IO_APIC && PCI_MSI && ACPI |
| select DMAR_TABLE |
| ---help--- |
| Supports Interrupt remapping for IO-APIC and MSI devices. |
| To use x2apic mode in the CPU's which support x2APIC enhancements or |
| to support platforms with CPU's having > 8 bit APIC ID, say Y. |
| |
| # OMAP IOMMU support |
| config OMAP_IOMMU |
| bool "OMAP IOMMU Support" |
| depends on ARM && MMU |
| depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| select IOMMU_API |
| ---help--- |
| The OMAP3 media platform drivers depend on iommu support, |
| if you need them say Y here. |
| |
| config OMAP_IOMMU_DEBUG |
| bool "Export OMAP IOMMU internals in DebugFS" |
| depends on OMAP_IOMMU && DEBUG_FS |
| ---help--- |
| Select this to see extensive information about |
| the internal state of OMAP IOMMU in debugfs. |
| |
| Say N unless you know you need this. |
| |
| config ROCKCHIP_IOMMU |
| bool "Rockchip IOMMU Support" |
| depends on ARM || ARM64 |
| depends on ARCH_ROCKCHIP || COMPILE_TEST |
| select IOMMU_API |
| select ARM_DMA_USE_IOMMU |
| help |
| Support for IOMMUs found on Rockchip rk32xx SOCs. |
| These IOMMUs allow virtualization of the address space used by most |
| cores within the multimedia subsystem. |
| Say Y here if you are using a Rockchip SoC that includes an IOMMU |
| device. |
| |
| config TEGRA_IOMMU_GART |
| bool "Tegra GART IOMMU Support" |
| depends on ARCH_TEGRA_2x_SOC |
| depends on TEGRA_MC |
| select IOMMU_API |
| help |
| Enables support for remapping discontiguous physical memory |
| shared with the operating system into contiguous I/O virtual |
| space through the GART (Graphics Address Relocation Table) |
| hardware included on Tegra SoCs. |
| |
| config TEGRA_IOMMU_SMMU |
| bool "NVIDIA Tegra SMMU Support" |
| depends on ARCH_TEGRA |
| depends on TEGRA_AHB |
| depends on TEGRA_MC |
| select IOMMU_API |
| help |
| This driver supports the IOMMU hardware (SMMU) found on NVIDIA Tegra |
| SoCs (Tegra30 up to Tegra210). |
| |
| config EXYNOS_IOMMU |
| bool "Exynos IOMMU Support" |
| depends on ARCH_EXYNOS && MMU |
| depends on !CPU_BIG_ENDIAN # revisit driver if we can enable big-endian ptes |
| select IOMMU_API |
| select ARM_DMA_USE_IOMMU |
| help |
| Support for the IOMMU (System MMU) of Samsung Exynos application |
| processor family. This enables H/W multimedia accelerators to see |
| non-linear physical memory chunks as linear memory in their |
| address space. |
| |
| If unsure, say N here. |
| |
| config EXYNOS_IOMMU_DEBUG |
| bool "Debugging log for Exynos IOMMU" |
| depends on EXYNOS_IOMMU |
| help |
| Select this to see the detailed log message that shows what |
| happens in the IOMMU driver. |
| |
| Say N unless you need kernel log message for IOMMU debugging. |
| |
| config IPMMU_VMSA |
| bool "Renesas VMSA-compatible IPMMU" |
| depends on ARM || IOMMU_DMA |
| depends on ARCH_RENESAS || (COMPILE_TEST && !GENERIC_ATOMIC64) |
| select IOMMU_API |
| select IOMMU_IO_PGTABLE_LPAE |
| select ARM_DMA_USE_IOMMU |
| help |
| Support for the Renesas VMSA-compatible IPMMU found in the R-Mobile |
| APE6, R-Car Gen2, and R-Car Gen3 SoCs. |
| |
| If unsure, say N. |
| |
| config SPAPR_TCE_IOMMU |
| bool "sPAPR TCE IOMMU Support" |
| depends on PPC_POWERNV || PPC_PSERIES |
| select IOMMU_API |
| help |
| Enables bits of IOMMU API required by VFIO. The iommu_ops |
| is not implemented as it is not necessary for VFIO. |
| |
| # ARM IOMMU support |
| config ARM_SMMU |
| bool "ARM Ltd. System MMU (SMMU) Support" |
| depends on (ARM64 || ARM) && MMU |
| select IOMMU_API |
| select IOMMU_IO_PGTABLE_LPAE |
| select ARM_DMA_USE_IOMMU if ARM |
| help |
| Support for implementations of the ARM System MMU architecture |
| versions 1 and 2. |
| |
| Say Y here if your SoC includes an IOMMU device implementing |
| the ARM SMMU architecture. |
| |
| config ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT |
| bool "Default to disabling bypass on ARM SMMU v1 and v2" |
| depends on ARM_SMMU |
| default y |
| help |
| Say Y here to (by default) disable bypass streams such that |
| incoming transactions from devices that are not attached to |
| an iommu domain will report an abort back to the device and |
| will not be allowed to pass through the SMMU. |
| |
| Any old kernels that existed before this KConfig was |
| introduced would default to _allowing_ bypass (AKA the |
| equivalent of NO for this config). However the default for |
| this option is YES because the old behavior is insecure. |
| |
| There are few reasons to allow unmatched stream bypass, and |
| even fewer good ones. If saying YES here breaks your board |
| you should work on fixing your board. This KConfig option |
| is expected to be removed in the future and we'll simply |
| hardcode the bypass disable in the code. |
| |
| NOTE: the kernel command line parameter |
| 'arm-smmu.disable_bypass' will continue to override this |
| config. |
| |
| config ARM_SMMU_V3 |
| bool "ARM Ltd. System MMU Version 3 (SMMUv3) Support" |
| depends on ARM64 |
| select IOMMU_API |
| select IOMMU_IO_PGTABLE_LPAE |
| select GENERIC_MSI_IRQ_DOMAIN |
| help |
| Support for implementations of the ARM System MMU architecture |
| version 3 providing translation support to a PCIe root complex. |
| |
| Say Y here if your system includes an IOMMU device implementing |
| the ARM SMMUv3 architecture. |
| |
| config S390_IOMMU |
| def_bool y if S390 && PCI |
| depends on S390 && PCI |
| select IOMMU_API |
| help |
| Support for the IOMMU API for s390 PCI devices. |
| |
| config S390_CCW_IOMMU |
| bool "S390 CCW IOMMU Support" |
| depends on S390 && CCW |
| select IOMMU_API |
| help |
| Enables bits of IOMMU API required by VFIO. The iommu_ops |
| is not implemented as it is not necessary for VFIO. |
| |
| config S390_AP_IOMMU |
| bool "S390 AP IOMMU Support" |
| depends on S390 && ZCRYPT |
| select IOMMU_API |
| help |
| Enables bits of IOMMU API required by VFIO. The iommu_ops |
| is not implemented as it is not necessary for VFIO. |
| |
| config MTK_IOMMU |
| bool "MTK IOMMU Support" |
| depends on ARM || ARM64 |
| depends on ARCH_MEDIATEK || COMPILE_TEST |
| select ARM_DMA_USE_IOMMU |
| select IOMMU_API |
| select IOMMU_DMA |
| select IOMMU_IO_PGTABLE_ARMV7S |
| select MEMORY |
| select MTK_SMI |
| help |
| Support for the M4U on certain Mediatek SOCs. M4U is MultiMedia |
| Memory Management Unit. This option enables remapping of DMA memory |
| accesses for the multimedia subsystem. |
| |
| If unsure, say N here. |
| |
| config MTK_IOMMU_V1 |
| bool "MTK IOMMU Version 1 (M4U gen1) Support" |
| depends on ARM |
| depends on ARCH_MEDIATEK || COMPILE_TEST |
| select ARM_DMA_USE_IOMMU |
| select IOMMU_API |
| select MEMORY |
| select MTK_SMI |
| help |
| Support for the M4U on certain Mediatek SoCs. M4U generation 1 HW is |
| Multimedia Memory Managememt Unit. This option enables remapping of |
| DMA memory accesses for the multimedia subsystem. |
| |
| if unsure, say N here. |
| |
| config QCOM_IOMMU |
| # Note: iommu drivers cannot (yet?) be built as modules |
| bool "Qualcomm IOMMU Support" |
| depends on ARCH_QCOM || (COMPILE_TEST && !GENERIC_ATOMIC64) |
| select IOMMU_API |
| select IOMMU_IO_PGTABLE_LPAE |
| select ARM_DMA_USE_IOMMU |
| help |
| Support for IOMMU on certain Qualcomm SoCs. |
| |
| config HYPERV_IOMMU |
| bool "Hyper-V x2APIC IRQ Handling" |
| depends on HYPERV && X86 |
| select IOMMU_API |
| default HYPERV |
| help |
| Stub IOMMU driver to handle IRQs as to allow Hyper-V Linux |
| guests to run with x2APIC mode enabled. |
| |
| config VIRTIO_IOMMU |
| bool "Virtio IOMMU driver" |
| depends on VIRTIO=y |
| depends on ARM64 |
| select IOMMU_API |
| select INTERVAL_TREE |
| help |
| Para-virtualised IOMMU driver with virtio. |
| |
| Say Y here if you intend to run this kernel as a guest. |
| |
| endif # IOMMU_SUPPORT |
