| /************************************************************************** |
| * |
| * Copyright 2000-2006 Alacritech, Inc. All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * 2. Redistributions in binary form must reproduce the above |
| * copyright notice, this list of conditions and the following |
| * disclaimer in the documentation and/or other materials provided |
| * with the distribution. |
| * |
| * Alternatively, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL") version 2 as published by the Free |
| * Software Foundation. |
| * |
| * THIS SOFTWARE IS PROVIDED BY ALACRITECH, INC. ``AS IS'' AND ANY |
| * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR |
| * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ALACRITECH, INC. OR |
| * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF |
| * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND |
| * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
| * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT |
| * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF |
| * SUCH DAMAGE. |
| * |
| * The views and conclusions contained in the software and documentation |
| * are those of the authors and should not be interpreted as representing |
| * official policies, either expressed or implied, of Alacritech, Inc. |
| * |
| **************************************************************************/ |
| |
| /* |
| * FILENAME: slicoss.c |
| * |
| * The SLICOSS driver for Alacritech's IS-NIC products. |
| * |
| * This driver is supposed to support: |
| * |
| * Mojave cards (single port PCI Gigabit) both copper and fiber |
| * Oasis cards (single and dual port PCI-x Gigabit) copper and fiber |
| * Kalahari cards (dual and quad port PCI-e Gigabit) copper and fiber |
| * |
| * The driver was acutally tested on Oasis and Kalahari cards. |
| * |
| * |
| * NOTE: This is the standard, non-accelerated version of Alacritech's |
| * IS-NIC driver. |
| */ |
| |
| |
| #define KLUDGE_FOR_4GB_BOUNDARY 1 |
| #define DEBUG_MICROCODE 1 |
| #define DBG 1 |
| #define SLIC_INTERRUPT_PROCESS_LIMIT 1 |
| #define SLIC_OFFLOAD_IP_CHECKSUM 1 |
| #define STATS_TIMER_INTERVAL 2 |
| #define PING_TIMER_INTERVAL 1 |
| |
| #include <linux/kernel.h> |
| #include <linux/string.h> |
| #include <linux/errno.h> |
| #include <linux/ioport.h> |
| #include <linux/slab.h> |
| #include <linux/interrupt.h> |
| #include <linux/timer.h> |
| #include <linux/pci.h> |
| #include <linux/spinlock.h> |
| #include <linux/init.h> |
| #include <linux/bitops.h> |
| #include <linux/io.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/skbuff.h> |
| #include <linux/delay.h> |
| #include <linux/debugfs.h> |
| #include <linux/seq_file.h> |
| #include <linux/kthread.h> |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| |
| #include <linux/firmware.h> |
| #include <linux/types.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/mii.h> |
| #include <linux/if_vlan.h> |
| #include <asm/unaligned.h> |
| |
| #include <linux/ethtool.h> |
| #include <linux/uaccess.h> |
| #include "slichw.h" |
| #include "slic.h" |
| |
| static struct net_device_stats *slic_get_stats(struct net_device *dev); |
| static int slic_entry_open(struct net_device *dev); |
| static int slic_entry_halt(struct net_device *dev); |
| static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); |
| static int slic_xmit_start(struct sk_buff *skb, struct net_device *dev); |
| static void slic_xmit_fail(struct adapter *adapter, struct sk_buff *skb, |
| void *cmd, u32 skbtype, u32 status); |
| static void slic_config_pci(struct pci_dev *pcidev); |
| static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter); |
| static int slic_mac_set_address(struct net_device *dev, void *ptr); |
| static void slic_link_event_handler(struct adapter *adapter); |
| static void slic_upr_request_complete(struct adapter *adapter, u32 isr); |
| static int slic_rspqueue_init(struct adapter *adapter); |
| static void slic_rspqueue_free(struct adapter *adapter); |
| static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter); |
| static int slic_cmdq_init(struct adapter *adapter); |
| static void slic_cmdq_free(struct adapter *adapter); |
| static void slic_cmdq_reset(struct adapter *adapter); |
| static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page); |
| static void slic_cmdq_getdone(struct adapter *adapter); |
| static void slic_cmdq_putdone_irq(struct adapter *adapter, |
| struct slic_hostcmd *cmd); |
| static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter); |
| static int slic_rcvqueue_init(struct adapter *adapter); |
| static int slic_rcvqueue_fill(struct adapter *adapter); |
| static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb); |
| static void slic_rcvqueue_free(struct adapter *adapter); |
| static void slic_adapter_set_hwaddr(struct adapter *adapter); |
| static int slic_card_init(struct sliccard *card, struct adapter *adapter); |
| static void slic_intagg_set(struct adapter *adapter, u32 value); |
| static int slic_card_download(struct adapter *adapter); |
| static u32 slic_card_locate(struct adapter *adapter); |
| static int slic_if_init(struct adapter *adapter); |
| static int slic_adapter_allocresources(struct adapter *adapter); |
| static void slic_adapter_freeresources(struct adapter *adapter); |
| static void slic_link_config(struct adapter *adapter, u32 linkspeed, |
| u32 linkduplex); |
| static void slic_unmap_mmio_space(struct adapter *adapter); |
| static void slic_card_cleanup(struct sliccard *card); |
| static void slic_soft_reset(struct adapter *adapter); |
| static bool slic_mac_filter(struct adapter *adapter, |
| struct ether_header *ether_frame); |
| static void slic_mac_address_config(struct adapter *adapter); |
| static void slic_mac_config(struct adapter *adapter); |
| static void slic_mcast_set_mask(struct adapter *adapter); |
| static void slic_config_set(struct adapter *adapter, bool linkchange); |
| static void slic_config_clear(struct adapter *adapter); |
| static void slic_config_get(struct adapter *adapter, u32 config, |
| u32 configh); |
| static void slic_timer_load_check(ulong context); |
| static void slic_assert_fail(void); |
| static ushort slic_eeprom_cksum(char *m, int len); |
| static void slic_upr_start(struct adapter *adapter); |
| static void slic_link_upr_complete(struct adapter *adapter, u32 Isr); |
| static int slic_upr_request(struct adapter *adapter, u32 upr_request, |
| u32 upr_data, u32 upr_data_h, u32 upr_buffer, |
| u32 upr_buffer_h); |
| static void slic_mcast_set_list(struct net_device *dev); |
| |
| |
| static uint slic_first_init = 1; |
| static char *slic_banner = "Alacritech SLIC Technology(tm) Server "\ |
| "and Storage Accelerator (Non-Accelerated)"; |
| |
| static char *slic_proc_version = "2.0.351 2006/07/14 12:26:00"; |
| static char *slic_product_name = "SLIC Technology(tm) Server "\ |
| "and Storage Accelerator (Non-Accelerated)"; |
| static char *slic_vendor = "Alacritech, Inc."; |
| |
| static int slic_debug = 1; |
| static int debug = -1; |
| static struct net_device *head_netdevice; |
| |
| static struct base_driver slic_global = { {}, 0, 0, 0, 1, NULL, NULL }; |
| static int intagg_delay = 100; |
| static u32 dynamic_intagg; |
| static unsigned int rcv_count; |
| static struct dentry *slic_debugfs; |
| |
| #define DRV_NAME "slicoss" |
| #define DRV_VERSION "2.0.1" |
| #define DRV_AUTHOR "Alacritech, Inc. Engineering" |
| #define DRV_DESCRIPTION "Alacritech SLIC Techonology(tm) "\ |
| "Non-Accelerated Driver" |
| #define DRV_COPYRIGHT "Copyright 2000-2006 Alacritech, Inc. "\ |
| "All rights reserved." |
| #define PFX DRV_NAME " " |
| |
| MODULE_AUTHOR(DRV_AUTHOR); |
| MODULE_DESCRIPTION(DRV_DESCRIPTION); |
| MODULE_LICENSE("Dual BSD/GPL"); |
| |
| module_param(dynamic_intagg, int, 0); |
| MODULE_PARM_DESC(dynamic_intagg, "Dynamic Interrupt Aggregation Setting"); |
| module_param(intagg_delay, int, 0); |
| MODULE_PARM_DESC(intagg_delay, "uSec Interrupt Aggregation Delay"); |
| |
| static struct pci_device_id slic_pci_tbl[] __devinitdata = { |
| {PCI_VENDOR_ID_ALACRITECH, |
| SLIC_1GB_DEVICE_ID, |
| PCI_ANY_ID, PCI_ANY_ID,}, |
| {PCI_VENDOR_ID_ALACRITECH, |
| SLIC_2GB_DEVICE_ID, |
| PCI_ANY_ID, PCI_ANY_ID,}, |
| {0,} |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, slic_pci_tbl); |
| |
| #ifdef ASSERT |
| #undef ASSERT |
| #endif |
| |
| #ifndef ASSERT |
| #define ASSERT(a) do { \ |
| if (!(a)) { \ |
| printk(KERN_ERR "slicoss ASSERT() Failure: function %s" \ |
| "line %d\n", __func__, __LINE__); \ |
| slic_assert_fail(); \ |
| } \ |
| } while (0) |
| #endif |
| |
| |
| #define SLIC_GET_SLIC_HANDLE(_adapter, _pslic_handle) \ |
| { \ |
| spin_lock_irqsave(&_adapter->handle_lock.lock, \ |
| _adapter->handle_lock.flags); \ |
| _pslic_handle = _adapter->pfree_slic_handles; \ |
| if (_pslic_handle) { \ |
| ASSERT(_pslic_handle->type == SLIC_HANDLE_FREE); \ |
| _adapter->pfree_slic_handles = _pslic_handle->next; \ |
| } \ |
| spin_unlock_irqrestore(&_adapter->handle_lock.lock, \ |
| _adapter->handle_lock.flags); \ |
| } |
| |
| #define SLIC_FREE_SLIC_HANDLE(_adapter, _pslic_handle) \ |
| { \ |
| _pslic_handle->type = SLIC_HANDLE_FREE; \ |
| spin_lock_irqsave(&_adapter->handle_lock.lock, \ |
| _adapter->handle_lock.flags); \ |
| _pslic_handle->next = _adapter->pfree_slic_handles; \ |
| _adapter->pfree_slic_handles = _pslic_handle; \ |
| spin_unlock_irqrestore(&_adapter->handle_lock.lock, \ |
| _adapter->handle_lock.flags); \ |
| } |
| |
| static void slic_debug_init(void); |
| static void slic_debug_cleanup(void); |
| static void slic_debug_adapter_create(struct adapter *adapter); |
| static void slic_debug_adapter_destroy(struct adapter *adapter); |
| static void slic_debug_card_create(struct sliccard *card); |
| static void slic_debug_card_destroy(struct sliccard *card); |
| |
| static inline void slic_reg32_write(void __iomem *reg, u32 value, bool flush) |
| { |
| writel(value, reg); |
| if (flush) |
| mb(); |
| } |
| |
| static inline void slic_reg64_write(struct adapter *adapter, void __iomem *reg, |
| u32 value, void __iomem *regh, u32 paddrh, |
| bool flush) |
| { |
| spin_lock_irqsave(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| if (paddrh != adapter->curaddrupper) { |
| adapter->curaddrupper = paddrh; |
| writel(paddrh, regh); |
| } |
| writel(value, reg); |
| if (flush) |
| mb(); |
| spin_unlock_irqrestore(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| } |
| |
| static void slic_init_driver(void) |
| { |
| if (slic_first_init) { |
| slic_first_init = 0; |
| spin_lock_init(&slic_global.driver_lock.lock); |
| slic_debug_init(); |
| } |
| } |
| |
| static void slic_init_adapter(struct net_device *netdev, |
| struct pci_dev *pcidev, |
| const struct pci_device_id *pci_tbl_entry, |
| void __iomem *memaddr, int chip_idx) |
| { |
| ushort index; |
| struct slic_handle *pslic_handle; |
| struct adapter *adapter = (struct adapter *)netdev_priv(netdev); |
| |
| /* adapter->pcidev = pcidev;*/ |
| adapter->vendid = pci_tbl_entry->vendor; |
| adapter->devid = pci_tbl_entry->device; |
| adapter->subsysid = pci_tbl_entry->subdevice; |
| adapter->busnumber = pcidev->bus->number; |
| adapter->slotnumber = ((pcidev->devfn >> 3) & 0x1F); |
| adapter->functionnumber = (pcidev->devfn & 0x7); |
| adapter->memorylength = pci_resource_len(pcidev, 0); |
| adapter->slic_regs = (__iomem struct slic_regs *)memaddr; |
| adapter->irq = pcidev->irq; |
| /* adapter->netdev = netdev;*/ |
| adapter->next_netdevice = head_netdevice; |
| head_netdevice = netdev; |
| adapter->chipid = chip_idx; |
| adapter->port = 0; /*adapter->functionnumber;*/ |
| adapter->cardindex = adapter->port; |
| adapter->memorybase = memaddr; |
| spin_lock_init(&adapter->upr_lock.lock); |
| spin_lock_init(&adapter->bit64reglock.lock); |
| spin_lock_init(&adapter->adapter_lock.lock); |
| spin_lock_init(&adapter->reset_lock.lock); |
| spin_lock_init(&adapter->handle_lock.lock); |
| |
| adapter->card_size = 1; |
| /* |
| Initialize slic_handle array |
| */ |
| ASSERT(SLIC_CMDQ_MAXCMDS <= 0xFFFF); |
| /* |
| Start with 1. 0 is an invalid host handle. |
| */ |
| for (index = 1, pslic_handle = &adapter->slic_handles[1]; |
| index < SLIC_CMDQ_MAXCMDS; index++, pslic_handle++) { |
| |
| pslic_handle->token.handle_index = index; |
| pslic_handle->type = SLIC_HANDLE_FREE; |
| pslic_handle->next = adapter->pfree_slic_handles; |
| adapter->pfree_slic_handles = pslic_handle; |
| } |
| adapter->pshmem = (struct slic_shmem *) |
| pci_alloc_consistent(adapter->pcidev, |
| sizeof(struct slic_shmem), |
| &adapter-> |
| phys_shmem); |
| ASSERT(adapter->pshmem); |
| |
| memset(adapter->pshmem, 0, sizeof(struct slic_shmem)); |
| |
| return; |
| } |
| |
| static int __devinit slic_entry_probe(struct pci_dev *pcidev, |
| const struct pci_device_id *pci_tbl_entry) |
| { |
| static int cards_found; |
| static int did_version; |
| int err = -ENODEV; |
| struct net_device *netdev; |
| struct adapter *adapter; |
| void __iomem *memmapped_ioaddr = NULL; |
| u32 status = 0; |
| ulong mmio_start = 0; |
| ulong mmio_len = 0; |
| struct sliccard *card = NULL; |
| |
| slic_global.dynamic_intagg = dynamic_intagg; |
| |
| err = pci_enable_device(pcidev); |
| |
| if (err) |
| return err; |
| |
| if (slic_debug > 0 && did_version++ == 0) { |
| printk(KERN_DEBUG "%s\n", slic_banner); |
| printk(KERN_DEBUG "%s\n", slic_proc_version); |
| } |
| |
| err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(64)); |
| if (err) { |
| err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(32)); |
| if (err) |
| goto err_out_disable_pci; |
| } |
| |
| err = pci_request_regions(pcidev, DRV_NAME); |
| if (err) |
| goto err_out_disable_pci; |
| |
| pci_set_master(pcidev); |
| |
| netdev = alloc_etherdev(sizeof(struct adapter)); |
| if (!netdev) { |
| err = -ENOMEM; |
| goto err_out_exit_slic_probe; |
| } |
| |
| SET_NETDEV_DEV(netdev, &pcidev->dev); |
| |
| pci_set_drvdata(pcidev, netdev); |
| adapter = netdev_priv(netdev); |
| adapter->netdev = netdev; |
| adapter->pcidev = pcidev; |
| |
| mmio_start = pci_resource_start(pcidev, 0); |
| mmio_len = pci_resource_len(pcidev, 0); |
| |
| |
| /* memmapped_ioaddr = (u32)ioremap_nocache(mmio_start, mmio_len);*/ |
| memmapped_ioaddr = ioremap(mmio_start, mmio_len); |
| if (!memmapped_ioaddr) { |
| dev_err(&pcidev->dev, "cannot remap MMIO region %lx @ %lx\n", |
| mmio_len, mmio_start); |
| goto err_out_free_netdev; |
| } |
| |
| slic_config_pci(pcidev); |
| |
| slic_init_driver(); |
| |
| slic_init_adapter(netdev, |
| pcidev, pci_tbl_entry, memmapped_ioaddr, cards_found); |
| |
| status = slic_card_locate(adapter); |
| if (status) { |
| dev_err(&pcidev->dev, "cannot locate card\n"); |
| goto err_out_free_mmio_region; |
| } |
| |
| card = adapter->card; |
| |
| if (!adapter->allocated) { |
| card->adapters_allocated++; |
| adapter->allocated = 1; |
| } |
| |
| status = slic_card_init(card, adapter); |
| |
| if (status != STATUS_SUCCESS) { |
| card->state = CARD_FAIL; |
| adapter->state = ADAPT_FAIL; |
| adapter->linkstate = LINK_DOWN; |
| dev_err(&pcidev->dev, "FAILED status[%x]\n", status); |
| } else { |
| slic_adapter_set_hwaddr(adapter); |
| } |
| |
| netdev->base_addr = (unsigned long)adapter->memorybase; |
| netdev->irq = adapter->irq; |
| netdev->open = slic_entry_open; |
| netdev->stop = slic_entry_halt; |
| netdev->hard_start_xmit = slic_xmit_start; |
| netdev->do_ioctl = slic_ioctl; |
| netdev->set_mac_address = slic_mac_set_address; |
| netdev->get_stats = slic_get_stats; |
| netdev->set_multicast_list = slic_mcast_set_list; |
| |
| slic_debug_adapter_create(adapter); |
| |
| strcpy(netdev->name, "eth%d"); |
| err = register_netdev(netdev); |
| if (err) { |
| dev_err(&pcidev->dev, "Cannot register net device, aborting.\n"); |
| goto err_out_unmap; |
| } |
| |
| cards_found++; |
| |
| return status; |
| |
| err_out_unmap: |
| iounmap(memmapped_ioaddr); |
| err_out_free_mmio_region: |
| release_mem_region(mmio_start, mmio_len); |
| err_out_free_netdev: |
| free_netdev(netdev); |
| err_out_exit_slic_probe: |
| pci_release_regions(pcidev); |
| err_out_disable_pci: |
| pci_disable_device(pcidev); |
| return err; |
| } |
| |
| static int slic_entry_open(struct net_device *dev) |
| { |
| struct adapter *adapter = (struct adapter *) netdev_priv(dev); |
| struct sliccard *card = adapter->card; |
| u32 locked = 0; |
| int status; |
| |
| ASSERT(adapter); |
| ASSERT(card); |
| |
| netif_stop_queue(adapter->netdev); |
| |
| spin_lock_irqsave(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| locked = 1; |
| if (!adapter->activated) { |
| card->adapters_activated++; |
| slic_global.num_slic_ports_active++; |
| adapter->activated = 1; |
| } |
| status = slic_if_init(adapter); |
| |
| if (status != STATUS_SUCCESS) { |
| if (adapter->activated) { |
| card->adapters_activated--; |
| slic_global.num_slic_ports_active--; |
| adapter->activated = 0; |
| } |
| if (locked) { |
| spin_unlock_irqrestore(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| locked = 0; |
| } |
| return status; |
| } |
| if (!card->master) |
| card->master = adapter; |
| |
| if (locked) { |
| spin_unlock_irqrestore(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| locked = 0; |
| } |
| |
| return STATUS_SUCCESS; |
| } |
| |
| static void __devexit slic_entry_remove(struct pci_dev *pcidev) |
| { |
| struct net_device *dev = pci_get_drvdata(pcidev); |
| u32 mmio_start = 0; |
| uint mmio_len = 0; |
| struct adapter *adapter = (struct adapter *) netdev_priv(dev); |
| struct sliccard *card; |
| struct mcast_address *mcaddr, *mlist; |
| |
| ASSERT(adapter); |
| slic_adapter_freeresources(adapter); |
| slic_unmap_mmio_space(adapter); |
| unregister_netdev(dev); |
| |
| mmio_start = pci_resource_start(pcidev, 0); |
| mmio_len = pci_resource_len(pcidev, 0); |
| |
| release_mem_region(mmio_start, mmio_len); |
| |
| iounmap((void __iomem *)dev->base_addr); |
| /* free multicast addresses */ |
| mlist = adapter->mcastaddrs; |
| while (mlist) { |
| mcaddr = mlist; |
| mlist = mlist->next; |
| kfree(mcaddr); |
| } |
| ASSERT(adapter->card); |
| card = adapter->card; |
| ASSERT(card->adapters_allocated); |
| card->adapters_allocated--; |
| adapter->allocated = 0; |
| if (!card->adapters_allocated) { |
| struct sliccard *curr_card = slic_global.slic_card; |
| if (curr_card == card) { |
| slic_global.slic_card = card->next; |
| } else { |
| while (curr_card->next != card) |
| curr_card = curr_card->next; |
| ASSERT(curr_card); |
| curr_card->next = card->next; |
| } |
| ASSERT(slic_global.num_slic_cards); |
| slic_global.num_slic_cards--; |
| slic_card_cleanup(card); |
| } |
| kfree(dev); |
| pci_release_regions(pcidev); |
| } |
| |
| static int slic_entry_halt(struct net_device *dev) |
| { |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| struct sliccard *card = adapter->card; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| spin_lock_irqsave(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| ASSERT(card); |
| netif_stop_queue(adapter->netdev); |
| adapter->state = ADAPT_DOWN; |
| adapter->linkstate = LINK_DOWN; |
| adapter->upr_list = NULL; |
| adapter->upr_busy = 0; |
| adapter->devflags_prev = 0; |
| ASSERT(card->adapter[adapter->cardindex] == adapter); |
| slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH); |
| adapter->all_reg_writes++; |
| adapter->icr_reg_writes++; |
| slic_config_clear(adapter); |
| if (adapter->activated) { |
| card->adapters_activated--; |
| slic_global.num_slic_ports_active--; |
| adapter->activated = 0; |
| } |
| #ifdef AUTOMATIC_RESET |
| slic_reg32_write(&slic_regs->slic_reset_iface, 0, FLUSH); |
| #endif |
| /* |
| * Reset the adapter's cmd queues |
| */ |
| slic_cmdq_reset(adapter); |
| |
| #ifdef AUTOMATIC_RESET |
| if (!card->adapters_activated) |
| slic_card_init(card, adapter); |
| #endif |
| |
| spin_unlock_irqrestore(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| return STATUS_SUCCESS; |
| } |
| |
| static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) |
| { |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| struct ethtool_cmd edata; |
| struct ethtool_cmd ecmd; |
| u32 data[7]; |
| u32 intagg; |
| |
| ASSERT(rq); |
| switch (cmd) { |
| case SIOCSLICSETINTAGG: |
| if (copy_from_user(data, rq->ifr_data, 28)) |
| return -EFAULT; |
| intagg = data[0]; |
| dev_err(&dev->dev, "%s: set interrupt aggregation to %d\n", |
| __func__, intagg); |
| slic_intagg_set(adapter, intagg); |
| return 0; |
| |
| #ifdef SLIC_TRACE_DUMP_ENABLED |
| case SIOCSLICTRACEDUMP: |
| { |
| u32 value; |
| DBG_IOCTL("slic_ioctl SIOCSLIC_TRACE_DUMP\n"); |
| |
| if (copy_from_user(data, rq->ifr_data, 28)) { |
| PRINT_ERROR |
| ("slic: copy_from_user FAILED getting \ |
| initial simba param\n"); |
| return -EFAULT; |
| } |
| |
| value = data[0]; |
| if (tracemon_request == SLIC_DUMP_DONE) { |
| PRINT_ERROR |
| ("ATK Diagnostic Trace Dump Requested\n"); |
| tracemon_request = SLIC_DUMP_REQUESTED; |
| tracemon_request_type = value; |
| tracemon_timestamp = jiffies; |
| } else if ((tracemon_request == SLIC_DUMP_REQUESTED) || |
| (tracemon_request == |
| SLIC_DUMP_IN_PROGRESS)) { |
| PRINT_ERROR |
| ("ATK Diagnostic Trace Dump Requested but \ |
| already in progress... ignore\n"); |
| } else { |
| PRINT_ERROR |
| ("ATK Diagnostic Trace Dump Requested\n"); |
| tracemon_request = SLIC_DUMP_REQUESTED; |
| tracemon_request_type = value; |
| tracemon_timestamp = jiffies; |
| } |
| return 0; |
| } |
| #endif |
| case SIOCETHTOOL: |
| ASSERT(adapter); |
| if (copy_from_user(&ecmd, rq->ifr_data, sizeof(ecmd))) |
| return -EFAULT; |
| |
| if (ecmd.cmd == ETHTOOL_GSET) { |
| edata.supported = (SUPPORTED_10baseT_Half | |
| SUPPORTED_10baseT_Full | |
| SUPPORTED_100baseT_Half | |
| SUPPORTED_100baseT_Full | |
| SUPPORTED_Autoneg | SUPPORTED_MII); |
| edata.port = PORT_MII; |
| edata.transceiver = XCVR_INTERNAL; |
| edata.phy_address = 0; |
| if (adapter->linkspeed == LINK_100MB) |
| edata.speed = SPEED_100; |
| else if (adapter->linkspeed == LINK_10MB) |
| edata.speed = SPEED_10; |
| else |
| edata.speed = 0; |
| |
| if (adapter->linkduplex == LINK_FULLD) |
| edata.duplex = DUPLEX_FULL; |
| else |
| edata.duplex = DUPLEX_HALF; |
| |
| edata.autoneg = AUTONEG_ENABLE; |
| edata.maxtxpkt = 1; |
| edata.maxrxpkt = 1; |
| if (copy_to_user(rq->ifr_data, &edata, sizeof(edata))) |
| return -EFAULT; |
| |
| } else if (ecmd.cmd == ETHTOOL_SSET) { |
| if (!capable(CAP_NET_ADMIN)) |
| return -EPERM; |
| |
| if (adapter->linkspeed == LINK_100MB) |
| edata.speed = SPEED_100; |
| else if (adapter->linkspeed == LINK_10MB) |
| edata.speed = SPEED_10; |
| else |
| edata.speed = 0; |
| |
| if (adapter->linkduplex == LINK_FULLD) |
| edata.duplex = DUPLEX_FULL; |
| else |
| edata.duplex = DUPLEX_HALF; |
| |
| edata.autoneg = AUTONEG_ENABLE; |
| edata.maxtxpkt = 1; |
| edata.maxrxpkt = 1; |
| if ((ecmd.speed != edata.speed) || |
| (ecmd.duplex != edata.duplex)) { |
| u32 speed; |
| u32 duplex; |
| |
| if (ecmd.speed == SPEED_10) |
| speed = 0; |
| else |
| speed = PCR_SPEED_100; |
| if (ecmd.duplex == DUPLEX_FULL) |
| duplex = PCR_DUPLEX_FULL; |
| else |
| duplex = 0; |
| slic_link_config(adapter, speed, duplex); |
| slic_link_event_handler(adapter); |
| } |
| } |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| #define XMIT_FAIL_LINK_STATE 1 |
| #define XMIT_FAIL_ZERO_LENGTH 2 |
| #define XMIT_FAIL_HOSTCMD_FAIL 3 |
| |
| static void slic_xmit_build_request(struct adapter *adapter, |
| struct slic_hostcmd *hcmd, struct sk_buff *skb) |
| { |
| struct slic_host64_cmd *ihcmd; |
| ulong phys_addr; |
| |
| ihcmd = &hcmd->cmd64; |
| |
| ihcmd->flags = (adapter->port << IHFLG_IFSHFT); |
| ihcmd->command = IHCMD_XMT_REQ; |
| ihcmd->u.slic_buffers.totlen = skb->len; |
| phys_addr = pci_map_single(adapter->pcidev, skb->data, skb->len, |
| PCI_DMA_TODEVICE); |
| ihcmd->u.slic_buffers.bufs[0].paddrl = SLIC_GET_ADDR_LOW(phys_addr); |
| ihcmd->u.slic_buffers.bufs[0].paddrh = SLIC_GET_ADDR_HIGH(phys_addr); |
| ihcmd->u.slic_buffers.bufs[0].length = skb->len; |
| #if defined(CONFIG_X86_64) |
| hcmd->cmdsize = (u32) ((((u64)&ihcmd->u.slic_buffers.bufs[1] - |
| (u64) hcmd) + 31) >> 5); |
| #elif defined(CONFIG_X86) |
| hcmd->cmdsize = ((((u32) &ihcmd->u.slic_buffers.bufs[1] - |
| (u32) hcmd) + 31) >> 5); |
| #else |
| Stop Compilation; |
| #endif |
| } |
| |
| #define NORMAL_ETHFRAME 0 |
| |
| static int slic_xmit_start(struct sk_buff *skb, struct net_device *dev) |
| { |
| struct sliccard *card; |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| struct slic_hostcmd *hcmd = NULL; |
| u32 status = 0; |
| u32 skbtype = NORMAL_ETHFRAME; |
| void *offloadcmd = NULL; |
| |
| card = adapter->card; |
| ASSERT(card); |
| if ((adapter->linkstate != LINK_UP) || |
| (adapter->state != ADAPT_UP) || (card->state != CARD_UP)) { |
| status = XMIT_FAIL_LINK_STATE; |
| goto xmit_fail; |
| |
| } else if (skb->len == 0) { |
| status = XMIT_FAIL_ZERO_LENGTH; |
| goto xmit_fail; |
| } |
| |
| if (skbtype == NORMAL_ETHFRAME) { |
| hcmd = slic_cmdq_getfree(adapter); |
| if (!hcmd) { |
| adapter->xmitq_full = 1; |
| status = XMIT_FAIL_HOSTCMD_FAIL; |
| goto xmit_fail; |
| } |
| ASSERT(hcmd->pslic_handle); |
| ASSERT(hcmd->cmd64.hosthandle == |
| hcmd->pslic_handle->token.handle_token); |
| hcmd->skb = skb; |
| hcmd->busy = 1; |
| hcmd->type = SLIC_CMD_DUMB; |
| if (skbtype == NORMAL_ETHFRAME) |
| slic_xmit_build_request(adapter, hcmd, skb); |
| } |
| adapter->stats.tx_packets++; |
| adapter->stats.tx_bytes += skb->len; |
| |
| #ifdef DEBUG_DUMP |
| if (adapter->kill_card) { |
| struct slic_host64_cmd ihcmd; |
| |
| ihcmd = &hcmd->cmd64; |
| |
| ihcmd->flags |= 0x40; |
| adapter->kill_card = 0; /* only do this once */ |
| } |
| #endif |
| if (hcmd->paddrh == 0) { |
| slic_reg32_write(&adapter->slic_regs->slic_cbar, |
| (hcmd->paddrl | hcmd->cmdsize), DONT_FLUSH); |
| } else { |
| slic_reg64_write(adapter, &adapter->slic_regs->slic_cbar64, |
| (hcmd->paddrl | hcmd->cmdsize), |
| &adapter->slic_regs->slic_addr_upper, |
| hcmd->paddrh, DONT_FLUSH); |
| } |
| xmit_done: |
| return 0; |
| xmit_fail: |
| slic_xmit_fail(adapter, skb, offloadcmd, skbtype, status); |
| goto xmit_done; |
| } |
| |
| static void slic_xmit_fail(struct adapter *adapter, |
| struct sk_buff *skb, |
| void *cmd, u32 skbtype, u32 status) |
| { |
| if (adapter->xmitq_full) |
| netif_stop_queue(adapter->netdev); |
| if ((cmd == NULL) && (status <= XMIT_FAIL_HOSTCMD_FAIL)) { |
| switch (status) { |
| case XMIT_FAIL_LINK_STATE: |
| dev_err(&adapter->netdev->dev, |
| "reject xmit skb[%p: %x] linkstate[%s] " |
| "adapter[%s:%d] card[%s:%d]\n", |
| skb, skb->pkt_type, |
| SLIC_LINKSTATE(adapter->linkstate), |
| SLIC_ADAPTER_STATE(adapter->state), |
| adapter->state, |
| SLIC_CARD_STATE(adapter->card->state), |
| adapter->card->state); |
| break; |
| case XMIT_FAIL_ZERO_LENGTH: |
| dev_err(&adapter->netdev->dev, |
| "xmit_start skb->len == 0 skb[%p] type[%x]\n", |
| skb, skb->pkt_type); |
| break; |
| case XMIT_FAIL_HOSTCMD_FAIL: |
| dev_err(&adapter->netdev->dev, |
| "xmit_start skb[%p] type[%x] No host commands " |
| "available\n", skb, skb->pkt_type); |
| break; |
| default: |
| ASSERT(0); |
| } |
| } |
| dev_kfree_skb(skb); |
| adapter->stats.tx_dropped++; |
| } |
| |
| static void slic_rcv_handle_error(struct adapter *adapter, |
| struct slic_rcvbuf *rcvbuf) |
| { |
| struct slic_hddr_wds *hdr = (struct slic_hddr_wds *)rcvbuf->data; |
| |
| if (adapter->devid != SLIC_1GB_DEVICE_ID) { |
| if (hdr->frame_status14 & VRHSTAT_802OE) |
| adapter->if_events.oflow802++; |
| if (hdr->frame_status14 & VRHSTAT_TPOFLO) |
| adapter->if_events.Tprtoflow++; |
| if (hdr->frame_status_b14 & VRHSTATB_802UE) |
| adapter->if_events.uflow802++; |
| if (hdr->frame_status_b14 & VRHSTATB_RCVE) { |
| adapter->if_events.rcvearly++; |
| adapter->stats.rx_fifo_errors++; |
| } |
| if (hdr->frame_status_b14 & VRHSTATB_BUFF) { |
| adapter->if_events.Bufov++; |
| adapter->stats.rx_over_errors++; |
| } |
| if (hdr->frame_status_b14 & VRHSTATB_CARRE) { |
| adapter->if_events.Carre++; |
| adapter->stats.tx_carrier_errors++; |
| } |
| if (hdr->frame_status_b14 & VRHSTATB_LONGE) |
| adapter->if_events.Longe++; |
| if (hdr->frame_status_b14 & VRHSTATB_PREA) |
| adapter->if_events.Invp++; |
| if (hdr->frame_status_b14 & VRHSTATB_CRC) { |
| adapter->if_events.Crc++; |
| adapter->stats.rx_crc_errors++; |
| } |
| if (hdr->frame_status_b14 & VRHSTATB_DRBL) |
| adapter->if_events.Drbl++; |
| if (hdr->frame_status_b14 & VRHSTATB_CODE) |
| adapter->if_events.Code++; |
| if (hdr->frame_status_b14 & VRHSTATB_TPCSUM) |
| adapter->if_events.TpCsum++; |
| if (hdr->frame_status_b14 & VRHSTATB_TPHLEN) |
| adapter->if_events.TpHlen++; |
| if (hdr->frame_status_b14 & VRHSTATB_IPCSUM) |
| adapter->if_events.IpCsum++; |
| if (hdr->frame_status_b14 & VRHSTATB_IPLERR) |
| adapter->if_events.IpLen++; |
| if (hdr->frame_status_b14 & VRHSTATB_IPHERR) |
| adapter->if_events.IpHlen++; |
| } else { |
| if (hdr->frame_statusGB & VGBSTAT_XPERR) { |
| u32 xerr = hdr->frame_statusGB >> VGBSTAT_XERRSHFT; |
| |
| if (xerr == VGBSTAT_XCSERR) |
| adapter->if_events.TpCsum++; |
| if (xerr == VGBSTAT_XUFLOW) |
| adapter->if_events.Tprtoflow++; |
| if (xerr == VGBSTAT_XHLEN) |
| adapter->if_events.TpHlen++; |
| } |
| if (hdr->frame_statusGB & VGBSTAT_NETERR) { |
| u32 nerr = |
| (hdr-> |
| frame_statusGB >> VGBSTAT_NERRSHFT) & |
| VGBSTAT_NERRMSK; |
| if (nerr == VGBSTAT_NCSERR) |
| adapter->if_events.IpCsum++; |
| if (nerr == VGBSTAT_NUFLOW) |
| adapter->if_events.IpLen++; |
| if (nerr == VGBSTAT_NHLEN) |
| adapter->if_events.IpHlen++; |
| } |
| if (hdr->frame_statusGB & VGBSTAT_LNKERR) { |
| u32 lerr = hdr->frame_statusGB & VGBSTAT_LERRMSK; |
| |
| if (lerr == VGBSTAT_LDEARLY) |
| adapter->if_events.rcvearly++; |
| if (lerr == VGBSTAT_LBOFLO) |
| adapter->if_events.Bufov++; |
| if (lerr == VGBSTAT_LCODERR) |
| adapter->if_events.Code++; |
| if (lerr == VGBSTAT_LDBLNBL) |
| adapter->if_events.Drbl++; |
| if (lerr == VGBSTAT_LCRCERR) |
| adapter->if_events.Crc++; |
| if (lerr == VGBSTAT_LOFLO) |
| adapter->if_events.oflow802++; |
| if (lerr == VGBSTAT_LUFLO) |
| adapter->if_events.uflow802++; |
| } |
| } |
| return; |
| } |
| |
| #define TCP_OFFLOAD_FRAME_PUSHFLAG 0x10000000 |
| #define M_FAST_PATH 0x0040 |
| |
| static void slic_rcv_handler(struct adapter *adapter) |
| { |
| struct sk_buff *skb; |
| struct slic_rcvbuf *rcvbuf; |
| u32 frames = 0; |
| |
| while ((skb = slic_rcvqueue_getnext(adapter))) { |
| u32 rx_bytes; |
| |
| ASSERT(skb->head); |
| rcvbuf = (struct slic_rcvbuf *)skb->head; |
| adapter->card->events++; |
| if (rcvbuf->status & IRHDDR_ERR) { |
| adapter->rx_errors++; |
| slic_rcv_handle_error(adapter, rcvbuf); |
| slic_rcvqueue_reinsert(adapter, skb); |
| continue; |
| } |
| |
| if (!slic_mac_filter(adapter, (struct ether_header *) |
| rcvbuf->data)) { |
| slic_rcvqueue_reinsert(adapter, skb); |
| continue; |
| } |
| skb_pull(skb, SLIC_RCVBUF_HEADSIZE); |
| rx_bytes = (rcvbuf->length & IRHDDR_FLEN_MSK); |
| skb_put(skb, rx_bytes); |
| adapter->stats.rx_packets++; |
| adapter->stats.rx_bytes += rx_bytes; |
| #if SLIC_OFFLOAD_IP_CHECKSUM |
| skb->ip_summed = CHECKSUM_UNNECESSARY; |
| #endif |
| |
| skb->dev = adapter->netdev; |
| skb->protocol = eth_type_trans(skb, skb->dev); |
| netif_rx(skb); |
| |
| ++frames; |
| #if SLIC_INTERRUPT_PROCESS_LIMIT |
| if (frames >= SLIC_RCVQ_MAX_PROCESS_ISR) { |
| adapter->rcv_interrupt_yields++; |
| break; |
| } |
| #endif |
| } |
| adapter->max_isr_rcvs = max(adapter->max_isr_rcvs, frames); |
| } |
| |
| static void slic_xmit_complete(struct adapter *adapter) |
| { |
| struct slic_hostcmd *hcmd; |
| struct slic_rspbuf *rspbuf; |
| u32 frames = 0; |
| struct slic_handle_word slic_handle_word; |
| |
| do { |
| rspbuf = slic_rspqueue_getnext(adapter); |
| if (!rspbuf) |
| break; |
| adapter->xmit_completes++; |
| adapter->card->events++; |
| /* |
| Get the complete host command buffer |
| */ |
| slic_handle_word.handle_token = rspbuf->hosthandle; |
| ASSERT(slic_handle_word.handle_index); |
| ASSERT(slic_handle_word.handle_index <= SLIC_CMDQ_MAXCMDS); |
| hcmd = |
| (struct slic_hostcmd *) |
| adapter->slic_handles[slic_handle_word.handle_index]. |
| address; |
| /* hcmd = (struct slic_hostcmd *) rspbuf->hosthandle; */ |
| ASSERT(hcmd); |
| ASSERT(hcmd->pslic_handle == |
| &adapter->slic_handles[slic_handle_word.handle_index]); |
| if (hcmd->type == SLIC_CMD_DUMB) { |
| if (hcmd->skb) |
| dev_kfree_skb_irq(hcmd->skb); |
| slic_cmdq_putdone_irq(adapter, hcmd); |
| } |
| rspbuf->status = 0; |
| rspbuf->hosthandle = 0; |
| frames++; |
| } while (1); |
| adapter->max_isr_xmits = max(adapter->max_isr_xmits, frames); |
| } |
| |
| static irqreturn_t slic_interrupt(int irq, void *dev_id) |
| { |
| struct net_device *dev = (struct net_device *)dev_id; |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| u32 isr; |
| |
| if ((adapter->pshmem) && (adapter->pshmem->isr)) { |
| slic_reg32_write(&adapter->slic_regs->slic_icr, |
| ICR_INT_MASK, FLUSH); |
| isr = adapter->isrcopy = adapter->pshmem->isr; |
| adapter->pshmem->isr = 0; |
| adapter->num_isrs++; |
| switch (adapter->card->state) { |
| case CARD_UP: |
| if (isr & ~ISR_IO) { |
| if (isr & ISR_ERR) { |
| adapter->error_interrupts++; |
| if (isr & ISR_RMISS) { |
| int count; |
| int pre_count; |
| int errors; |
| |
| struct slic_rcvqueue *rcvq = |
| &adapter->rcvqueue; |
| |
| adapter-> |
| error_rmiss_interrupts++; |
| if (!rcvq->errors) |
| rcv_count = rcvq->count; |
| pre_count = rcvq->count; |
| errors = rcvq->errors; |
| |
| while (rcvq->count < |
| SLIC_RCVQ_FILLTHRESH) { |
| count = |
| slic_rcvqueue_fill |
| (adapter); |
| if (!count) |
| break; |
| } |
| } else if (isr & ISR_XDROP) { |
| dev_err(&dev->dev, |
| "isr & ISR_ERR [%x] " |
| "ISR_XDROP \n", isr); |
| } else { |
| dev_err(&dev->dev, |
| "isr & ISR_ERR [%x]\n", |
| isr); |
| } |
| } |
| |
| if (isr & ISR_LEVENT) { |
| adapter->linkevent_interrupts++; |
| slic_link_event_handler(adapter); |
| } |
| |
| if ((isr & ISR_UPC) || |
| (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) { |
| adapter->upr_interrupts++; |
| slic_upr_request_complete(adapter, isr); |
| } |
| } |
| |
| if (isr & ISR_RCV) { |
| adapter->rcv_interrupts++; |
| slic_rcv_handler(adapter); |
| } |
| |
| if (isr & ISR_CMD) { |
| adapter->xmit_interrupts++; |
| slic_xmit_complete(adapter); |
| } |
| break; |
| |
| case CARD_DOWN: |
| if ((isr & ISR_UPC) || |
| (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) { |
| adapter->upr_interrupts++; |
| slic_upr_request_complete(adapter, isr); |
| } |
| break; |
| |
| default: |
| break; |
| } |
| |
| adapter->isrcopy = 0; |
| adapter->all_reg_writes += 2; |
| adapter->isr_reg_writes++; |
| slic_reg32_write(&adapter->slic_regs->slic_isr, 0, FLUSH); |
| } else { |
| adapter->false_interrupts++; |
| } |
| return IRQ_HANDLED; |
| } |
| |
| /* |
| * slic_link_event_handler - |
| * |
| * Initiate a link configuration sequence. The link configuration begins |
| * by issuing a READ_LINK_STATUS command to the Utility Processor on the |
| * SLIC. Since the command finishes asynchronously, the slic_upr_comlete |
| * routine will follow it up witha UP configuration write command, which |
| * will also complete asynchronously. |
| * |
| */ |
| static void slic_link_event_handler(struct adapter *adapter) |
| { |
| int status; |
| struct slic_shmem *pshmem; |
| |
| if (adapter->state != ADAPT_UP) { |
| /* Adapter is not operational. Ignore. */ |
| return; |
| } |
| |
| pshmem = (struct slic_shmem *)adapter->phys_shmem; |
| |
| #if defined(CONFIG_X86_64) |
| status = slic_upr_request(adapter, |
| SLIC_UPR_RLSR, |
| SLIC_GET_ADDR_LOW(&pshmem->linkstatus), |
| SLIC_GET_ADDR_HIGH(&pshmem->linkstatus), |
| 0, 0); |
| #elif defined(CONFIG_X86) |
| status = slic_upr_request(adapter, SLIC_UPR_RLSR, |
| (u32) &pshmem->linkstatus, /* no 4GB wrap guaranteed */ |
| 0, 0, 0); |
| #else |
| Stop compilation; |
| #endif |
| ASSERT((status == STATUS_SUCCESS) || (status == STATUS_PENDING)); |
| } |
| |
| static void slic_init_cleanup(struct adapter *adapter) |
| { |
| if (adapter->intrregistered) { |
| adapter->intrregistered = 0; |
| free_irq(adapter->netdev->irq, adapter->netdev); |
| |
| } |
| if (adapter->pshmem) { |
| pci_free_consistent(adapter->pcidev, |
| sizeof(struct slic_shmem), |
| adapter->pshmem, adapter->phys_shmem); |
| adapter->pshmem = NULL; |
| adapter->phys_shmem = (dma_addr_t) NULL; |
| } |
| |
| if (adapter->pingtimerset) { |
| adapter->pingtimerset = 0; |
| del_timer(&adapter->pingtimer); |
| } |
| |
| slic_rspqueue_free(adapter); |
| slic_cmdq_free(adapter); |
| slic_rcvqueue_free(adapter); |
| } |
| |
| static struct net_device_stats *slic_get_stats(struct net_device *dev) |
| { |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| struct net_device_stats *stats; |
| |
| ASSERT(adapter); |
| stats = &adapter->stats; |
| stats->collisions = adapter->slic_stats.iface.xmit_collisions; |
| stats->rx_errors = adapter->slic_stats.iface.rcv_errors; |
| stats->tx_errors = adapter->slic_stats.iface.xmt_errors; |
| stats->rx_missed_errors = adapter->slic_stats.iface.rcv_discards; |
| stats->tx_heartbeat_errors = 0; |
| stats->tx_aborted_errors = 0; |
| stats->tx_window_errors = 0; |
| stats->tx_fifo_errors = 0; |
| stats->rx_frame_errors = 0; |
| stats->rx_length_errors = 0; |
| return &adapter->stats; |
| } |
| |
| /* |
| * Allocate a mcast_address structure to hold the multicast address. |
| * Link it in. |
| */ |
| static int slic_mcast_add_list(struct adapter *adapter, char *address) |
| { |
| struct mcast_address *mcaddr, *mlist; |
| bool equaladdr; |
| |
| /* Check to see if it already exists */ |
| mlist = adapter->mcastaddrs; |
| while (mlist) { |
| ETHER_EQ_ADDR(mlist->address, address, equaladdr); |
| if (equaladdr) |
| return STATUS_SUCCESS; |
| mlist = mlist->next; |
| } |
| |
| /* Doesn't already exist. Allocate a structure to hold it */ |
| mcaddr = kmalloc(sizeof(struct mcast_address), GFP_KERNEL); |
| if (mcaddr == NULL) |
| return 1; |
| |
| memcpy(mcaddr->address, address, 6); |
| |
| mcaddr->next = adapter->mcastaddrs; |
| adapter->mcastaddrs = mcaddr; |
| |
| return STATUS_SUCCESS; |
| } |
| |
| /* |
| * Functions to obtain the CRC corresponding to the destination mac address. |
| * This is a standard ethernet CRC in that it is a 32-bit, reflected CRC using |
| * the polynomial: |
| * x^32 + x^26 + x^23 + x^22 + x^16 + x^12 + x^11 + x^10 + x^8 + x^7 + x^5 + |
| * x^4 + x^2 + x^1. |
| * |
| * After the CRC for the 6 bytes is generated (but before the value is |
| * complemented), |
| * we must then transpose the value and return bits 30-23. |
| * |
| */ |
| static u32 slic_crc_table[256]; /* Table of CRCs for all possible byte values */ |
| static u32 slic_crc_init; /* Is table initialized */ |
| |
| /* |
| * Contruct the CRC32 table |
| */ |
| static void slic_mcast_init_crc32(void) |
| { |
| u32 c; /* CRC shit reg */ |
| u32 e = 0; /* Poly X-or pattern */ |
| int i; /* counter */ |
| int k; /* byte being shifted into crc */ |
| |
| static int p[] = { 0, 1, 2, 4, 5, 7, 8, 10, 11, 12, 16, 22, 23, 26 }; |
| |
| for (i = 0; i < sizeof(p) / sizeof(int); i++) |
| e |= 1L << (31 - p[i]); |
| |
| for (i = 1; i < 256; i++) { |
| c = i; |
| for (k = 8; k; k--) |
| c = c & 1 ? (c >> 1) ^ e : c >> 1; |
| slic_crc_table[i] = c; |
| } |
| } |
| |
| /* |
| * Return the MAC hast as described above. |
| */ |
| static unsigned char slic_mcast_get_mac_hash(char *macaddr) |
| { |
| u32 crc; |
| char *p; |
| int i; |
| unsigned char machash = 0; |
| |
| if (!slic_crc_init) { |
| slic_mcast_init_crc32(); |
| slic_crc_init = 1; |
| } |
| |
| crc = 0xFFFFFFFF; /* Preload shift register, per crc-32 spec */ |
| for (i = 0, p = macaddr; i < 6; ++p, ++i) |
| crc = (crc >> 8) ^ slic_crc_table[(crc ^ *p) & 0xFF]; |
| |
| /* Return bits 1-8, transposed */ |
| for (i = 1; i < 9; i++) |
| machash |= (((crc >> i) & 1) << (8 - i)); |
| |
| return machash; |
| } |
| |
| static void slic_mcast_set_bit(struct adapter *adapter, char *address) |
| { |
| unsigned char crcpoly; |
| |
| /* Get the CRC polynomial for the mac address */ |
| crcpoly = slic_mcast_get_mac_hash(address); |
| |
| /* We only have space on the SLIC for 64 entries. Lop |
| * off the top two bits. (2^6 = 64) |
| */ |
| crcpoly &= 0x3F; |
| |
| /* OR in the new bit into our 64 bit mask. */ |
| adapter->mcastmask |= (u64) 1 << crcpoly; |
| } |
| |
| static void slic_mcast_set_list(struct net_device *dev) |
| { |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| int status = STATUS_SUCCESS; |
| int i; |
| char *addresses; |
| struct dev_mc_list *mc_list = dev->mc_list; |
| int mc_count = dev->mc_count; |
| |
| ASSERT(adapter); |
| |
| for (i = 1; i <= mc_count; i++) { |
| addresses = (char *) &mc_list->dmi_addr; |
| if (mc_list->dmi_addrlen == 6) { |
| status = slic_mcast_add_list(adapter, addresses); |
| if (status != STATUS_SUCCESS) |
| break; |
| } else { |
| status = -EINVAL; |
| break; |
| } |
| slic_mcast_set_bit(adapter, addresses); |
| mc_list = mc_list->next; |
| } |
| |
| if (adapter->devflags_prev != dev->flags) { |
| adapter->macopts = MAC_DIRECTED; |
| if (dev->flags) { |
| if (dev->flags & IFF_BROADCAST) |
| adapter->macopts |= MAC_BCAST; |
| if (dev->flags & IFF_PROMISC) |
| adapter->macopts |= MAC_PROMISC; |
| if (dev->flags & IFF_ALLMULTI) |
| adapter->macopts |= MAC_ALLMCAST; |
| if (dev->flags & IFF_MULTICAST) |
| adapter->macopts |= MAC_MCAST; |
| } |
| adapter->devflags_prev = dev->flags; |
| slic_config_set(adapter, true); |
| } else { |
| if (status == STATUS_SUCCESS) |
| slic_mcast_set_mask(adapter); |
| } |
| return; |
| } |
| |
| static void slic_mcast_set_mask(struct adapter *adapter) |
| { |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| if (adapter->macopts & (MAC_ALLMCAST | MAC_PROMISC)) { |
| /* Turn on all multicast addresses. We have to do this for |
| * promiscuous mode as well as ALLMCAST mode. It saves the |
| * Microcode from having to keep state about the MAC |
| * configuration. |
| */ |
| slic_reg32_write(&slic_regs->slic_mcastlow, 0xFFFFFFFF, FLUSH); |
| slic_reg32_write(&slic_regs->slic_mcasthigh, 0xFFFFFFFF, |
| FLUSH); |
| } else { |
| /* Commit our multicast mast to the SLIC by writing to the |
| * multicast address mask registers |
| */ |
| slic_reg32_write(&slic_regs->slic_mcastlow, |
| (u32)(adapter->mcastmask & 0xFFFFFFFF), FLUSH); |
| slic_reg32_write(&slic_regs->slic_mcasthigh, |
| (u32)((adapter->mcastmask >> 32) & 0xFFFFFFFF), FLUSH); |
| } |
| } |
| |
| static void slic_timer_ping(ulong dev) |
| { |
| struct adapter *adapter; |
| struct sliccard *card; |
| |
| ASSERT(dev); |
| adapter = netdev_priv((struct net_device *)dev); |
| ASSERT(adapter); |
| card = adapter->card; |
| ASSERT(card); |
| |
| adapter->pingtimer.expires = jiffies + (PING_TIMER_INTERVAL * HZ); |
| add_timer(&adapter->pingtimer); |
| } |
| |
| /* |
| * slic_if_init |
| * |
| * Perform initialization of our slic interface. |
| * |
| */ |
| static int slic_if_init(struct adapter *adapter) |
| { |
| struct sliccard *card = adapter->card; |
| struct net_device *dev = adapter->netdev; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| struct slic_shmem *pshmem; |
| int status = 0; |
| |
| ASSERT(card); |
| |
| /* adapter should be down at this point */ |
| if (adapter->state != ADAPT_DOWN) { |
| dev_err(&dev->dev, "%s: adapter->state != ADAPT_DOWN\n", |
| __func__); |
| return -EIO; |
| } |
| ASSERT(adapter->linkstate == LINK_DOWN); |
| |
| adapter->devflags_prev = dev->flags; |
| adapter->macopts = MAC_DIRECTED; |
| if (dev->flags) { |
| if (dev->flags & IFF_BROADCAST) |
| adapter->macopts |= MAC_BCAST; |
| if (dev->flags & IFF_PROMISC) |
| adapter->macopts |= MAC_PROMISC; |
| if (dev->flags & IFF_ALLMULTI) |
| adapter->macopts |= MAC_ALLMCAST; |
| if (dev->flags & IFF_MULTICAST) |
| adapter->macopts |= MAC_MCAST; |
| } |
| status = slic_adapter_allocresources(adapter); |
| if (status != STATUS_SUCCESS) { |
| dev_err(&dev->dev, |
| "%s: slic_adapter_allocresources FAILED %x\n", |
| __func__, status); |
| slic_adapter_freeresources(adapter); |
| return status; |
| } |
| |
| if (!adapter->queues_initialized) { |
| if (slic_rspqueue_init(adapter)) |
| return -ENOMEM; |
| if (slic_cmdq_init(adapter)) |
| return -ENOMEM; |
| if (slic_rcvqueue_init(adapter)) |
| return -ENOMEM; |
| adapter->queues_initialized = 1; |
| } |
| |
| slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH); |
| mdelay(1); |
| |
| if (!adapter->isp_initialized) { |
| pshmem = (struct slic_shmem *)adapter->phys_shmem; |
| |
| spin_lock_irqsave(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| |
| #if defined(CONFIG_X86_64) |
| slic_reg32_write(&slic_regs->slic_addr_upper, |
| SLIC_GET_ADDR_HIGH(&pshmem->isr), DONT_FLUSH); |
| slic_reg32_write(&slic_regs->slic_isp, |
| SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH); |
| #elif defined(CONFIG_X86) |
| slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH); |
| slic_reg32_write(&slic_regs->slic_isp, (u32)&pshmem->isr, FLUSH); |
| #else |
| Stop Compilations |
| #endif |
| spin_unlock_irqrestore(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| adapter->isp_initialized = 1; |
| } |
| |
| adapter->state = ADAPT_UP; |
| if (!card->loadtimerset) { |
| init_timer(&card->loadtimer); |
| card->loadtimer.expires = |
| jiffies + (SLIC_LOADTIMER_PERIOD * HZ); |
| card->loadtimer.data = (ulong) card; |
| card->loadtimer.function = &slic_timer_load_check; |
| add_timer(&card->loadtimer); |
| |
| card->loadtimerset = 1; |
| } |
| |
| if (!adapter->pingtimerset) { |
| init_timer(&adapter->pingtimer); |
| adapter->pingtimer.expires = |
| jiffies + (PING_TIMER_INTERVAL * HZ); |
| adapter->pingtimer.data = (ulong) dev; |
| adapter->pingtimer.function = &slic_timer_ping; |
| add_timer(&adapter->pingtimer); |
| adapter->pingtimerset = 1; |
| adapter->card->pingstatus = ISR_PINGMASK; |
| } |
| |
| /* |
| * clear any pending events, then enable interrupts |
| */ |
| adapter->isrcopy = 0; |
| adapter->pshmem->isr = 0; |
| slic_reg32_write(&slic_regs->slic_isr, 0, FLUSH); |
| slic_reg32_write(&slic_regs->slic_icr, ICR_INT_ON, FLUSH); |
| |
| slic_link_config(adapter, LINK_AUTOSPEED, LINK_AUTOD); |
| slic_link_event_handler(adapter); |
| |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_unmap_mmio_space(struct adapter *adapter) |
| { |
| if (adapter->slic_regs) |
| iounmap(adapter->slic_regs); |
| adapter->slic_regs = NULL; |
| } |
| |
| static int slic_adapter_allocresources(struct adapter *adapter) |
| { |
| if (!adapter->intrregistered) { |
| int retval; |
| |
| spin_unlock_irqrestore(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| |
| retval = request_irq(adapter->netdev->irq, |
| &slic_interrupt, |
| IRQF_SHARED, |
| adapter->netdev->name, adapter->netdev); |
| |
| spin_lock_irqsave(&slic_global.driver_lock.lock, |
| slic_global.driver_lock.flags); |
| |
| if (retval) { |
| dev_err(&adapter->netdev->dev, |
| "request_irq (%s) FAILED [%x]\n", |
| adapter->netdev->name, retval); |
| return retval; |
| } |
| adapter->intrregistered = 1; |
| } |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_config_pci(struct pci_dev *pcidev) |
| { |
| u16 pci_command; |
| u16 new_command; |
| |
| pci_read_config_word(pcidev, PCI_COMMAND, &pci_command); |
| |
| new_command = pci_command | PCI_COMMAND_MASTER |
| | PCI_COMMAND_MEMORY |
| | PCI_COMMAND_INVALIDATE |
| | PCI_COMMAND_PARITY | PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK; |
| if (pci_command != new_command) |
| pci_write_config_word(pcidev, PCI_COMMAND, new_command); |
| } |
| |
| static void slic_adapter_freeresources(struct adapter *adapter) |
| { |
| slic_init_cleanup(adapter); |
| memset(&adapter->stats, 0, sizeof(struct net_device_stats)); |
| adapter->error_interrupts = 0; |
| adapter->rcv_interrupts = 0; |
| adapter->xmit_interrupts = 0; |
| adapter->linkevent_interrupts = 0; |
| adapter->upr_interrupts = 0; |
| adapter->num_isrs = 0; |
| adapter->xmit_completes = 0; |
| adapter->rcv_broadcasts = 0; |
| adapter->rcv_multicasts = 0; |
| adapter->rcv_unicasts = 0; |
| } |
| |
| /* |
| * slic_link_config |
| * |
| * Write phy control to configure link duplex/speed |
| * |
| */ |
| static void slic_link_config(struct adapter *adapter, |
| u32 linkspeed, u32 linkduplex) |
| { |
| u32 __iomem *wphy; |
| u32 speed; |
| u32 duplex; |
| u32 phy_config; |
| u32 phy_advreg; |
| u32 phy_gctlreg; |
| |
| if (adapter->state != ADAPT_UP) |
| return; |
| |
| ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID) |
| || (adapter->devid == SLIC_2GB_DEVICE_ID)); |
| |
| if (linkspeed > LINK_1000MB) |
| linkspeed = LINK_AUTOSPEED; |
| if (linkduplex > LINK_AUTOD) |
| linkduplex = LINK_AUTOD; |
| |
| wphy = &adapter->slic_regs->slic_wphy; |
| |
| if ((linkspeed == LINK_AUTOSPEED) || (linkspeed == LINK_1000MB)) { |
| if (adapter->flags & ADAPT_FLAGS_FIBERMEDIA) { |
| /* We've got a fiber gigabit interface, and register |
| * 4 is different in fiber mode than in copper mode |
| */ |
| |
| /* advertise FD only @1000 Mb */ |
| phy_advreg = (MIICR_REG_4 | (PAR_ADV1000XFD)); |
| /* enable PAUSE frames */ |
| phy_advreg |= PAR_ASYMPAUSE_FIBER; |
| slic_reg32_write(wphy, phy_advreg, FLUSH); |
| |
| if (linkspeed == LINK_AUTOSPEED) { |
| /* reset phy, enable auto-neg */ |
| phy_config = |
| (MIICR_REG_PCR | |
| (PCR_RESET | PCR_AUTONEG | |
| PCR_AUTONEG_RST)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } else { /* forced 1000 Mb FD*/ |
| /* power down phy to break link |
| this may not work) */ |
| phy_config = (MIICR_REG_PCR | PCR_POWERDOWN); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| /* wait, Marvell says 1 sec, |
| try to get away with 10 ms */ |
| mdelay(10); |
| |
| /* disable auto-neg, set speed/duplex, |
| soft reset phy, powerup */ |
| phy_config = |
| (MIICR_REG_PCR | |
| (PCR_RESET | PCR_SPEED_1000 | |
| PCR_DUPLEX_FULL)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } |
| } else { /* copper gigabit */ |
| |
| /* Auto-Negotiate or 1000 Mb must be auto negotiated |
| * We've got a copper gigabit interface, and |
| * register 4 is different in copper mode than |
| * in fiber mode |
| */ |
| if (linkspeed == LINK_AUTOSPEED) { |
| /* advertise 10/100 Mb modes */ |
| phy_advreg = |
| (MIICR_REG_4 | |
| (PAR_ADV100FD | PAR_ADV100HD | PAR_ADV10FD |
| | PAR_ADV10HD)); |
| } else { |
| /* linkspeed == LINK_1000MB - |
| don't advertise 10/100 Mb modes */ |
| phy_advreg = MIICR_REG_4; |
| } |
| /* enable PAUSE frames */ |
| phy_advreg |= PAR_ASYMPAUSE; |
| /* required by the Cicada PHY */ |
| phy_advreg |= PAR_802_3; |
| slic_reg32_write(wphy, phy_advreg, FLUSH); |
| /* advertise FD only @1000 Mb */ |
| phy_gctlreg = (MIICR_REG_9 | (PGC_ADV1000FD)); |
| slic_reg32_write(wphy, phy_gctlreg, FLUSH); |
| |
| if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) { |
| /* if a Marvell PHY |
| enable auto crossover */ |
| phy_config = |
| (MIICR_REG_16 | (MRV_REG16_XOVERON)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| |
| /* reset phy, enable auto-neg */ |
| phy_config = |
| (MIICR_REG_PCR | |
| (PCR_RESET | PCR_AUTONEG | |
| PCR_AUTONEG_RST)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } else { /* it's a Cicada PHY */ |
| /* enable and restart auto-neg (don't reset) */ |
| phy_config = |
| (MIICR_REG_PCR | |
| (PCR_AUTONEG | PCR_AUTONEG_RST)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } |
| } |
| } else { |
| /* Forced 10/100 */ |
| if (linkspeed == LINK_10MB) |
| speed = 0; |
| else |
| speed = PCR_SPEED_100; |
| if (linkduplex == LINK_HALFD) |
| duplex = 0; |
| else |
| duplex = PCR_DUPLEX_FULL; |
| |
| if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) { |
| /* if a Marvell PHY |
| disable auto crossover */ |
| phy_config = (MIICR_REG_16 | (MRV_REG16_XOVEROFF)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } |
| |
| /* power down phy to break link (this may not work) */ |
| phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN | speed | duplex)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| |
| /* wait, Marvell says 1 sec, try to get away with 10 ms */ |
| mdelay(10); |
| |
| if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) { |
| /* if a Marvell PHY |
| disable auto-neg, set speed, |
| soft reset phy, powerup */ |
| phy_config = |
| (MIICR_REG_PCR | (PCR_RESET | speed | duplex)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } else { /* it's a Cicada PHY */ |
| /* disable auto-neg, set speed, powerup */ |
| phy_config = (MIICR_REG_PCR | (speed | duplex)); |
| slic_reg32_write(wphy, phy_config, FLUSH); |
| } |
| } |
| } |
| |
| static void slic_card_cleanup(struct sliccard *card) |
| { |
| if (card->loadtimerset) { |
| card->loadtimerset = 0; |
| del_timer(&card->loadtimer); |
| } |
| |
| slic_debug_card_destroy(card); |
| |
| kfree(card); |
| } |
| |
| static int slic_card_download_gbrcv(struct adapter *adapter) |
| { |
| const struct firmware *fw; |
| const char *file = ""; |
| int ret; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| u32 codeaddr; |
| u32 instruction; |
| int index = 0; |
| u32 rcvucodelen = 0; |
| |
| switch (adapter->devid) { |
| case SLIC_2GB_DEVICE_ID: |
| file = "slicoss/oasisrcvucode.sys"; |
| break; |
| case SLIC_1GB_DEVICE_ID: |
| file = "slicoss/gbrcvucode.sys"; |
| break; |
| default: |
| ASSERT(0); |
| break; |
| } |
| |
| ret = request_firmware(&fw, file, &adapter->pcidev->dev); |
| if (ret) { |
| dev_err(&adapter->pcidev->dev, |
| "SLICOSS: Failed to load firmware %s\n", file); |
| return ret; |
| } |
| |
| rcvucodelen = *(u32 *)(fw->data + index); |
| index += 4; |
| switch (adapter->devid) { |
| case SLIC_2GB_DEVICE_ID: |
| if (rcvucodelen != OasisRcvUCodeLen) |
| return -EINVAL; |
| break; |
| case SLIC_1GB_DEVICE_ID: |
| if (rcvucodelen != GBRcvUCodeLen) |
| return -EINVAL; |
| break; |
| default: |
| ASSERT(0); |
| break; |
| } |
| /* start download */ |
| slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_BEGIN, FLUSH); |
| /* download the rcv sequencer ucode */ |
| for (codeaddr = 0; codeaddr < rcvucodelen; codeaddr++) { |
| /* write out instruction address */ |
| slic_reg32_write(&slic_regs->slic_rcv_wcs, codeaddr, FLUSH); |
| |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| /* write out the instruction data low addr */ |
| slic_reg32_write(&slic_regs->slic_rcv_wcs, instruction, FLUSH); |
| |
| instruction = *(u8 *)(fw->data + index); |
| index++; |
| /* write out the instruction data high addr */ |
| slic_reg32_write(&slic_regs->slic_rcv_wcs, (u8)instruction, |
| FLUSH); |
| } |
| |
| /* download finished */ |
| release_firmware(fw); |
| slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_FINISH, FLUSH); |
| return 0; |
| } |
| |
| static int slic_card_download(struct adapter *adapter) |
| { |
| const struct firmware *fw; |
| const char *file = ""; |
| int ret; |
| u32 section; |
| int thissectionsize; |
| int codeaddr; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| u32 instruction; |
| u32 baseaddress; |
| u32 failure; |
| u32 i; |
| u32 numsects = 0; |
| u32 sectsize[3]; |
| u32 sectstart[3]; |
| int ucode_start, index = 0; |
| |
| switch (adapter->devid) { |
| case SLIC_2GB_DEVICE_ID: |
| file = "slicoss/oasisdownload.sys"; |
| break; |
| case SLIC_1GB_DEVICE_ID: |
| file = "slicoss/gbdownload.sys"; |
| break; |
| default: |
| ASSERT(0); |
| break; |
| } |
| ret = request_firmware(&fw, file, &adapter->pcidev->dev); |
| if (ret) { |
| dev_err(&adapter->pcidev->dev, |
| "SLICOSS: Failed to load firmware %s\n", file); |
| return ret; |
| } |
| numsects = *(u32 *)(fw->data + index); |
| index += 4; |
| ASSERT(numsects <= 3); |
| for (i = 0; i < numsects; i++) { |
| sectsize[i] = *(u32 *)(fw->data + index); |
| index += 4; |
| } |
| for (i = 0; i < numsects; i++) { |
| sectstart[i] = *(u32 *)(fw->data + index); |
| index += 4; |
| } |
| ucode_start = index; |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| for (section = 0; section < numsects; section++) { |
| baseaddress = sectstart[section]; |
| thissectionsize = sectsize[section] >> 3; |
| |
| for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) { |
| /* Write out instruction address */ |
| slic_reg32_write(&slic_regs->slic_wcs, |
| baseaddress + codeaddr, FLUSH); |
| /* Write out instruction to low addr */ |
| slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH); |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| |
| /* Write out instruction to high addr */ |
| slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH); |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| } |
| } |
| index = ucode_start; |
| for (section = 0; section < numsects; section++) { |
| instruction = *(u32 *)(fw->data + index); |
| baseaddress = sectstart[section]; |
| if (baseaddress < 0x8000) |
| continue; |
| thissectionsize = sectsize[section] >> 3; |
| |
| for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) { |
| /* Write out instruction address */ |
| slic_reg32_write(&slic_regs->slic_wcs, |
| SLIC_WCS_COMPARE | (baseaddress + codeaddr), |
| FLUSH); |
| /* Write out instruction to low addr */ |
| slic_reg32_write(&slic_regs->slic_wcs, instruction, |
| FLUSH); |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| /* Write out instruction to high addr */ |
| slic_reg32_write(&slic_regs->slic_wcs, instruction, |
| FLUSH); |
| instruction = *(u32 *)(fw->data + index); |
| index += 4; |
| |
| /* Check SRAM location zero. If it is non-zero. Abort.*/ |
| /* failure = readl((u32 __iomem *)&slic_regs->slic_reset); |
| if (failure) { |
| release_firmware(fw); |
| return -EIO; |
| }*/ |
| } |
| } |
| release_firmware(fw); |
| /* Everything OK, kick off the card */ |
| mdelay(10); |
| slic_reg32_write(&slic_regs->slic_wcs, SLIC_WCS_START, FLUSH); |
| |
| /* stall for 20 ms, long enough for ucode to init card |
| and reach mainloop */ |
| mdelay(20); |
| |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_adapter_set_hwaddr(struct adapter *adapter) |
| { |
| struct sliccard *card = adapter->card; |
| |
| if ((adapter->card) && (card->config_set)) { |
| memcpy(adapter->macaddr, |
| card->config.MacInfo[adapter->functionnumber].macaddrA, |
| sizeof(struct slic_config_mac)); |
| if (!(adapter->currmacaddr[0] || adapter->currmacaddr[1] || |
| adapter->currmacaddr[2] || adapter->currmacaddr[3] || |
| adapter->currmacaddr[4] || adapter->currmacaddr[5])) { |
| memcpy(adapter->currmacaddr, adapter->macaddr, 6); |
| } |
| if (adapter->netdev) { |
| memcpy(adapter->netdev->dev_addr, adapter->currmacaddr, |
| 6); |
| } |
| } |
| } |
| |
| static void slic_intagg_set(struct adapter *adapter, u32 value) |
| { |
| slic_reg32_write(&adapter->slic_regs->slic_intagg, value, FLUSH); |
| adapter->card->loadlevel_current = value; |
| } |
| |
| static int slic_card_init(struct sliccard *card, struct adapter *adapter) |
| { |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| struct slic_eeprom *peeprom; |
| struct oslic_eeprom *pOeeprom; |
| dma_addr_t phys_config; |
| u32 phys_configh; |
| u32 phys_configl; |
| u32 i = 0; |
| struct slic_shmem *pshmem; |
| int status; |
| uint macaddrs = card->card_size; |
| ushort eecodesize; |
| ushort dramsize; |
| ushort ee_chksum; |
| ushort calc_chksum; |
| struct slic_config_mac *pmac; |
| unsigned char fruformat; |
| unsigned char oemfruformat; |
| struct atk_fru *patkfru; |
| union oemfru *poemfru; |
| |
| /* Reset everything except PCI configuration space */ |
| slic_soft_reset(adapter); |
| |
| /* Download the microcode */ |
| status = slic_card_download(adapter); |
| |
| if (status != STATUS_SUCCESS) { |
| dev_err(&adapter->pcidev->dev, |
| "download failed bus %d slot %d\n", |
| adapter->busnumber, adapter->slotnumber); |
| return status; |
| } |
| |
| if (!card->config_set) { |
| peeprom = pci_alloc_consistent(adapter->pcidev, |
| sizeof(struct slic_eeprom), |
| &phys_config); |
| |
| phys_configl = SLIC_GET_ADDR_LOW(phys_config); |
| phys_configh = SLIC_GET_ADDR_HIGH(phys_config); |
| |
| if (!peeprom) { |
| dev_err(&adapter->pcidev->dev, |
| "eeprom read failed to get memory " |
| "bus %d slot %d\n", adapter->busnumber, |
| adapter->slotnumber); |
| return -ENOMEM; |
| } else { |
| memset(peeprom, 0, sizeof(struct slic_eeprom)); |
| } |
| slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH); |
| mdelay(1); |
| pshmem = (struct slic_shmem *)adapter->phys_shmem; |
| |
| spin_lock_irqsave(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH); |
| slic_reg32_write(&slic_regs->slic_isp, |
| SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH); |
| spin_unlock_irqrestore(&adapter->bit64reglock.lock, |
| adapter->bit64reglock.flags); |
| |
| slic_config_get(adapter, phys_configl, phys_configh); |
| |
| for (;;) { |
| if (adapter->pshmem->isr) { |
| if (adapter->pshmem->isr & ISR_UPC) { |
| adapter->pshmem->isr = 0; |
| slic_reg64_write(adapter, |
| &slic_regs->slic_isp, 0, |
| &slic_regs->slic_addr_upper, |
| 0, FLUSH); |
| slic_reg32_write(&slic_regs->slic_isr, |
| 0, FLUSH); |
| |
| slic_upr_request_complete(adapter, 0); |
| break; |
| } else { |
| adapter->pshmem->isr = 0; |
| slic_reg32_write(&slic_regs->slic_isr, |
| 0, FLUSH); |
| } |
| } else { |
| mdelay(1); |
| i++; |
| if (i > 5000) { |
| dev_err(&adapter->pcidev->dev, |
| "%d config data fetch timed out!\n", |
| adapter->port); |
| slic_reg64_write(adapter, |
| &slic_regs->slic_isp, 0, |
| &slic_regs->slic_addr_upper, |
| 0, FLUSH); |
| return -EINVAL; |
| } |
| } |
| } |
| |
| switch (adapter->devid) { |
| /* Oasis card */ |
| case SLIC_2GB_DEVICE_ID: |
| /* extract EEPROM data and pointers to EEPROM data */ |
| pOeeprom = (struct oslic_eeprom *) peeprom; |
| eecodesize = pOeeprom->EecodeSize; |
| dramsize = pOeeprom->DramSize; |
| pmac = pOeeprom->MacInfo; |
| fruformat = pOeeprom->FruFormat; |
| patkfru = &pOeeprom->AtkFru; |
| oemfruformat = pOeeprom->OemFruFormat; |
| poemfru = &pOeeprom->OemFru; |
| macaddrs = 2; |
| /* Minor kludge for Oasis card |
| get 2 MAC addresses from the |
| EEPROM to ensure that function 1 |
| gets the Port 1 MAC address */ |
| break; |
| default: |
| /* extract EEPROM data and pointers to EEPROM data */ |
| eecodesize = peeprom->EecodeSize; |
| dramsize = peeprom->DramSize; |
| pmac = peeprom->u2.mac.MacInfo; |
| fruformat = peeprom->FruFormat; |
| patkfru = &peeprom->AtkFru; |
| oemfruformat = peeprom->OemFruFormat; |
| poemfru = &peeprom->OemFru; |
| break; |
| } |
| |
| card->config.EepromValid = false; |
| |
| /* see if the EEPROM is valid by checking it's checksum */ |
| if ((eecodesize <= MAX_EECODE_SIZE) && |
| (eecodesize >= MIN_EECODE_SIZE)) { |
| |
| ee_chksum = |
| *(u16 *) ((char *) peeprom + (eecodesize - 2)); |
| /* |
| calculate the EEPROM checksum |
| */ |
| calc_chksum = |
| ~slic_eeprom_cksum((char *) peeprom, |
| (eecodesize - 2)); |
| /* |
| if the ucdoe chksum flag bit worked, |
| we wouldn't need this shit |
| */ |
| if (ee_chksum == calc_chksum) |
| card->config.EepromValid = true; |
| } |
| /* copy in the DRAM size */ |
| card->config.DramSize = dramsize; |
| |
| /* copy in the MAC address(es) */ |
| for (i = 0; i < macaddrs; i++) { |
| memcpy(&card->config.MacInfo[i], |
| &pmac[i], sizeof(struct slic_config_mac)); |
| } |
| |
| /* copy the Alacritech FRU information */ |
| card->config.FruFormat = fruformat; |
| memcpy(&card->config.AtkFru, patkfru, |
| sizeof(struct atk_fru)); |
| |
| pci_free_consistent(adapter->pcidev, |
| sizeof(struct slic_eeprom), |
| peeprom, phys_config); |
| |
| if ((!card->config.EepromValid) && |
| (adapter->reg_params.fail_on_bad_eeprom)) { |
| slic_reg64_write(adapter, &slic_regs->slic_isp, 0, |
| &slic_regs->slic_addr_upper, |
| 0, FLUSH); |
| dev_err(&adapter->pcidev->dev, |
| "unsupported CONFIGURATION EEPROM invalid\n"); |
| return -EINVAL; |
| } |
| |
| card->config_set = 1; |
| } |
| |
| if (slic_card_download_gbrcv(adapter)) { |
| dev_err(&adapter->pcidev->dev, |
| "unable to download GB receive microcode\n"); |
| return -EINVAL; |
| } |
| |
| if (slic_global.dynamic_intagg) |
| slic_intagg_set(adapter, 0); |
| else |
| slic_intagg_set(adapter, intagg_delay); |
| |
| /* |
| * Initialize ping status to "ok" |
| */ |
| card->pingstatus = ISR_PINGMASK; |
| |
| /* |
| * Lastly, mark our card state as up and return success |
| */ |
| card->state = CARD_UP; |
| card->reset_in_progress = 0; |
| |
| return STATUS_SUCCESS; |
| } |
| |
| static u32 slic_card_locate(struct adapter *adapter) |
| { |
| struct sliccard *card = slic_global.slic_card; |
| struct physcard *physcard = slic_global.phys_card; |
| ushort card_hostid; |
| u16 __iomem *hostid_reg; |
| uint i; |
| uint rdhostid_offset = 0; |
| |
| switch (adapter->devid) { |
| case SLIC_2GB_DEVICE_ID: |
| rdhostid_offset = SLIC_RDHOSTID_2GB; |
| break; |
| case SLIC_1GB_DEVICE_ID: |
| rdhostid_offset = SLIC_RDHOSTID_1GB; |
| break; |
| default: |
| ASSERT(0); |
| break; |
| } |
| |
| hostid_reg = |
| (u16 __iomem *) (((u8 __iomem *) (adapter->slic_regs)) + |
| rdhostid_offset); |
| |
| /* read the 16 bit hostid from SRAM */ |
| card_hostid = (ushort) readw(hostid_reg); |
| |
| /* Initialize a new card structure if need be */ |
| if (card_hostid == SLIC_HOSTID_DEFAULT) { |
| card = kzalloc(sizeof(struct sliccard), GFP_KERNEL); |
| if (card == NULL) |
| return -ENOMEM; |
| |
| card->next = slic_global.slic_card; |
| slic_global.slic_card = card; |
| card->busnumber = adapter->busnumber; |
| card->slotnumber = adapter->slotnumber; |
| |
| /* Find an available cardnum */ |
| for (i = 0; i < SLIC_MAX_CARDS; i++) { |
| if (slic_global.cardnuminuse[i] == 0) { |
| slic_global.cardnuminuse[i] = 1; |
| card->cardnum = i; |
| break; |
| } |
| } |
| slic_global.num_slic_cards++; |
| |
| slic_debug_card_create(card); |
| } else { |
| /* Card exists, find the card this adapter belongs to */ |
| while (card) { |
| if (card->cardnum == card_hostid) |
| break; |
| card = card->next; |
| } |
| } |
| |
| ASSERT(card); |
| if (!card) |
| return STATUS_FAILURE; |
| /* Put the adapter in the card's adapter list */ |
| ASSERT(card->adapter[adapter->port] == NULL); |
| if (!card->adapter[adapter->port]) { |
| card->adapter[adapter->port] = adapter; |
| adapter->card = card; |
| } |
| |
| card->card_size = 1; /* one port per *logical* card */ |
| |
| while (physcard) { |
| for (i = 0; i < SLIC_MAX_PORTS; i++) { |
| if (!physcard->adapter[i]) |
| continue; |
| else |
| break; |
| } |
| ASSERT(i != SLIC_MAX_PORTS); |
| if (physcard->adapter[i]->slotnumber == adapter->slotnumber) |
| break; |
| physcard = physcard->next; |
| } |
| if (!physcard) { |
| /* no structure allocated for this physical card yet */ |
| physcard = kzalloc(sizeof(struct physcard), GFP_KERNEL); |
| ASSERT(physcard); |
| |
| physcard->next = slic_global.phys_card; |
| slic_global.phys_card = physcard; |
| physcard->adapters_allocd = 1; |
| } else { |
| physcard->adapters_allocd++; |
| } |
| /* Note - this is ZERO relative */ |
| adapter->physport = physcard->adapters_allocd - 1; |
| |
| ASSERT(physcard->adapter[adapter->physport] == NULL); |
| physcard->adapter[adapter->physport] = adapter; |
| adapter->physcard = physcard; |
| |
| return 0; |
| } |
| |
| static void slic_soft_reset(struct adapter *adapter) |
| { |
| if (adapter->card->state == CARD_UP) { |
| slic_reg32_write(&adapter->slic_regs->slic_quiesce, 0, FLUSH); |
| mdelay(1); |
| } |
| |
| slic_reg32_write(&adapter->slic_regs->slic_reset, SLIC_RESET_MAGIC, |
| FLUSH); |
| mdelay(1); |
| } |
| |
| static void slic_config_set(struct adapter *adapter, bool linkchange) |
| { |
| u32 value; |
| u32 RcrReset; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| if (linkchange) { |
| /* Setup MAC */ |
| slic_mac_config(adapter); |
| RcrReset = GRCR_RESET; |
| } else { |
| slic_mac_address_config(adapter); |
| RcrReset = 0; |
| } |
| |
| if (adapter->linkduplex == LINK_FULLD) { |
| /* setup xmtcfg */ |
| value = (GXCR_RESET | /* Always reset */ |
| GXCR_XMTEN | /* Enable transmit */ |
| GXCR_PAUSEEN); /* Enable pause */ |
| |
| slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH); |
| |
| /* Setup rcvcfg last */ |
| value = (RcrReset | /* Reset, if linkchange */ |
| GRCR_CTLEN | /* Enable CTL frames */ |
| GRCR_ADDRAEN | /* Address A enable */ |
| GRCR_RCVBAD | /* Rcv bad frames */ |
| (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT)); |
| } else { |
| /* setup xmtcfg */ |
| value = (GXCR_RESET | /* Always reset */ |
| GXCR_XMTEN); /* Enable transmit */ |
| |
| slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH); |
| |
| /* Setup rcvcfg last */ |
| value = (RcrReset | /* Reset, if linkchange */ |
| GRCR_ADDRAEN | /* Address A enable */ |
| GRCR_RCVBAD | /* Rcv bad frames */ |
| (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT)); |
| } |
| |
| if (adapter->state != ADAPT_DOWN) { |
| /* Only enable receive if we are restarting or running */ |
| value |= GRCR_RCVEN; |
| } |
| |
| if (adapter->macopts & MAC_PROMISC) |
| value |= GRCR_RCVALL; |
| |
| slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH); |
| } |
| |
| /* |
| * Turn off RCV and XMT, power down PHY |
| */ |
| static void slic_config_clear(struct adapter *adapter) |
| { |
| u32 value; |
| u32 phy_config; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| /* Setup xmtcfg */ |
| value = (GXCR_RESET | /* Always reset */ |
| GXCR_PAUSEEN); /* Enable pause */ |
| |
| slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH); |
| |
| value = (GRCR_RESET | /* Always reset */ |
| GRCR_CTLEN | /* Enable CTL frames */ |
| GRCR_ADDRAEN | /* Address A enable */ |
| (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT)); |
| |
| slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH); |
| |
| /* power down phy */ |
| phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN)); |
| slic_reg32_write(&slic_regs->slic_wphy, phy_config, FLUSH); |
| } |
| |
| static void slic_config_get(struct adapter *adapter, u32 config, |
| u32 config_h) |
| { |
| int status; |
| |
| status = slic_upr_request(adapter, |
| SLIC_UPR_RCONFIG, |
| (u32) config, (u32) config_h, 0, 0); |
| ASSERT(status == 0); |
| } |
| |
| static void slic_mac_address_config(struct adapter *adapter) |
| { |
| u32 value; |
| u32 value2; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| value = *(u32 *) &adapter->currmacaddr[2]; |
| value = ntohl(value); |
| slic_reg32_write(&slic_regs->slic_wraddral, value, FLUSH); |
| slic_reg32_write(&slic_regs->slic_wraddrbl, value, FLUSH); |
| |
| value2 = (u32) ((adapter->currmacaddr[0] << 8 | |
| adapter->currmacaddr[1]) & 0xFFFF); |
| |
| slic_reg32_write(&slic_regs->slic_wraddrah, value2, FLUSH); |
| slic_reg32_write(&slic_regs->slic_wraddrbh, value2, FLUSH); |
| |
| /* Write our multicast mask out to the card. This is done */ |
| /* here in addition to the slic_mcast_addr_set routine */ |
| /* because ALL_MCAST may have been enabled or disabled */ |
| slic_mcast_set_mask(adapter); |
| } |
| |
| static void slic_mac_config(struct adapter *adapter) |
| { |
| u32 value; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| |
| /* Setup GMAC gaps */ |
| if (adapter->linkspeed == LINK_1000MB) { |
| value = ((GMCR_GAPBB_1000 << GMCR_GAPBB_SHIFT) | |
| (GMCR_GAPR1_1000 << GMCR_GAPR1_SHIFT) | |
| (GMCR_GAPR2_1000 << GMCR_GAPR2_SHIFT)); |
| } else { |
| value = ((GMCR_GAPBB_100 << GMCR_GAPBB_SHIFT) | |
| (GMCR_GAPR1_100 << GMCR_GAPR1_SHIFT) | |
| (GMCR_GAPR2_100 << GMCR_GAPR2_SHIFT)); |
| } |
| |
| /* enable GMII */ |
| if (adapter->linkspeed == LINK_1000MB) |
| value |= GMCR_GBIT; |
| |
| /* enable fullduplex */ |
| if ((adapter->linkduplex == LINK_FULLD) |
| || (adapter->macopts & MAC_LOOPBACK)) { |
| value |= GMCR_FULLD; |
| } |
| |
| /* write mac config */ |
| slic_reg32_write(&slic_regs->slic_wmcfg, value, FLUSH); |
| |
| /* setup mac addresses */ |
| slic_mac_address_config(adapter); |
| } |
| |
| static bool slic_mac_filter(struct adapter *adapter, |
| struct ether_header *ether_frame) |
| { |
| u32 opts = adapter->macopts; |
| u32 *dhost4 = (u32 *)ðer_frame->ether_dhost[0]; |
| u16 *dhost2 = (u16 *)ðer_frame->ether_dhost[4]; |
| bool equaladdr; |
| |
| if (opts & MAC_PROMISC) |
| return true; |
| |
| if ((*dhost4 == 0xFFFFFFFF) && (*dhost2 == 0xFFFF)) { |
| if (opts & MAC_BCAST) { |
| adapter->rcv_broadcasts++; |
| return true; |
| } else { |
| return false; |
| } |
| } |
| |
| if (ether_frame->ether_dhost[0] & 0x01) { |
| if (opts & MAC_ALLMCAST) { |
| adapter->rcv_multicasts++; |
| adapter->stats.multicast++; |
| return true; |
| } |
| if (opts & MAC_MCAST) { |
| struct mcast_address *mcaddr = adapter->mcastaddrs; |
| |
| while (mcaddr) { |
| ETHER_EQ_ADDR(mcaddr->address, |
| ether_frame->ether_dhost, |
| equaladdr); |
| if (equaladdr) { |
| adapter->rcv_multicasts++; |
| adapter->stats.multicast++; |
| return true; |
| } |
| mcaddr = mcaddr->next; |
| } |
| return false; |
| } else { |
| return false; |
| } |
| } |
| if (opts & MAC_DIRECTED) { |
| adapter->rcv_unicasts++; |
| return true; |
| } |
| return false; |
| |
| } |
| |
| static int slic_mac_set_address(struct net_device *dev, void *ptr) |
| { |
| struct adapter *adapter = (struct adapter *)netdev_priv(dev); |
| struct sockaddr *addr = ptr; |
| |
| if (netif_running(dev)) |
| return -EBUSY; |
| if (!adapter) |
| return -EBUSY; |
| |
| memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); |
| memcpy(adapter->currmacaddr, addr->sa_data, dev->addr_len); |
| |
| slic_config_set(adapter, true); |
| return 0; |
| } |
| |
| static void slic_timer_load_check(ulong cardaddr) |
| { |
| struct sliccard *card = (struct sliccard *)cardaddr; |
| struct adapter *adapter = card->master; |
| u32 __iomem *intagg; |
| u32 load = card->events; |
| u32 level = 0; |
| |
| intagg = &adapter->slic_regs->slic_intagg; |
| |
| if ((adapter) && (adapter->state == ADAPT_UP) && |
| (card->state == CARD_UP) && (slic_global.dynamic_intagg)) { |
| if (adapter->devid == SLIC_1GB_DEVICE_ID) { |
| if (adapter->linkspeed == LINK_1000MB) |
| level = 100; |
| else { |
| if (load > SLIC_LOAD_5) |
| level = SLIC_INTAGG_5; |
| else if (load > SLIC_LOAD_4) |
| level = SLIC_INTAGG_4; |
| else if (load > SLIC_LOAD_3) |
| level = SLIC_INTAGG_3; |
| else if (load > SLIC_LOAD_2) |
| level = SLIC_INTAGG_2; |
| else if (load > SLIC_LOAD_1) |
| level = SLIC_INTAGG_1; |
| else |
| level = SLIC_INTAGG_0; |
| } |
| if (card->loadlevel_current != level) { |
| card->loadlevel_current = level; |
| slic_reg32_write(intagg, level, FLUSH); |
| } |
| } else { |
| if (load > SLIC_LOAD_5) |
| level = SLIC_INTAGG_5; |
| else if (load > SLIC_LOAD_4) |
| level = SLIC_INTAGG_4; |
| else if (load > SLIC_LOAD_3) |
| level = SLIC_INTAGG_3; |
| else if (load > SLIC_LOAD_2) |
| level = SLIC_INTAGG_2; |
| else if (load > SLIC_LOAD_1) |
| level = SLIC_INTAGG_1; |
| else |
| level = SLIC_INTAGG_0; |
| if (card->loadlevel_current != level) { |
| card->loadlevel_current = level; |
| slic_reg32_write(intagg, level, FLUSH); |
| } |
| } |
| } |
| card->events = 0; |
| card->loadtimer.expires = jiffies + (SLIC_LOADTIMER_PERIOD * HZ); |
| add_timer(&card->loadtimer); |
| } |
| |
| static void slic_assert_fail(void) |
| { |
| u32 cpuid; |
| u32 curr_pid; |
| cpuid = smp_processor_id(); |
| curr_pid = current->pid; |
| |
| printk(KERN_ERR "%s CPU # %d ---- PID # %d\n", |
| __func__, cpuid, curr_pid); |
| } |
| |
| static int slic_upr_queue_request(struct adapter *adapter, |
| u32 upr_request, |
| u32 upr_data, |
| u32 upr_data_h, |
| u32 upr_buffer, u32 upr_buffer_h) |
| { |
| struct slic_upr *upr; |
| struct slic_upr *uprqueue; |
| |
| upr = kmalloc(sizeof(struct slic_upr), GFP_ATOMIC); |
| if (!upr) |
| return -ENOMEM; |
| |
| upr->adapter = adapter->port; |
| upr->upr_request = upr_request; |
| upr->upr_data = upr_data; |
| upr->upr_buffer = upr_buffer; |
| upr->upr_data_h = upr_data_h; |
| upr->upr_buffer_h = upr_buffer_h; |
| upr->next = NULL; |
| if (adapter->upr_list) { |
| uprqueue = adapter->upr_list; |
| |
| while (uprqueue->next) |
| uprqueue = uprqueue->next; |
| uprqueue->next = upr; |
| } else { |
| adapter->upr_list = upr; |
| } |
| return STATUS_SUCCESS; |
| } |
| |
| static int slic_upr_request(struct adapter *adapter, |
| u32 upr_request, |
| u32 upr_data, |
| u32 upr_data_h, |
| u32 upr_buffer, u32 upr_buffer_h) |
| { |
| int status; |
| |
| spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags); |
| status = slic_upr_queue_request(adapter, |
| upr_request, |
| upr_data, |
| upr_data_h, upr_buffer, upr_buffer_h); |
| if (status != STATUS_SUCCESS) { |
| spin_unlock_irqrestore(&adapter->upr_lock.lock, |
| adapter->upr_lock.flags); |
| return status; |
| } |
| slic_upr_start(adapter); |
| spin_unlock_irqrestore(&adapter->upr_lock.lock, |
| adapter->upr_lock.flags); |
| return STATUS_PENDING; |
| } |
| |
| static void slic_upr_request_complete(struct adapter *adapter, u32 isr) |
| { |
| struct sliccard *card = adapter->card; |
| struct slic_upr *upr; |
| |
| spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags); |
| upr = adapter->upr_list; |
| if (!upr) { |
| ASSERT(0); |
| spin_unlock_irqrestore(&adapter->upr_lock.lock, |
| adapter->upr_lock.flags); |
| return; |
| } |
| adapter->upr_list = upr->next; |
| upr->next = NULL; |
| adapter->upr_busy = 0; |
| ASSERT(adapter->port == upr->adapter); |
| switch (upr->upr_request) { |
| case SLIC_UPR_STATS: |
| { |
| struct slic_stats *slicstats = |
| (struct slic_stats *) &adapter->pshmem->inicstats; |
| struct slic_stats *newstats = slicstats; |
| struct slic_stats *old = &adapter->inicstats_prev; |
| struct slicnet_stats *stst = &adapter->slic_stats; |
| |
| if (isr & ISR_UPCERR) { |
| dev_err(&adapter->netdev->dev, |
| "SLIC_UPR_STATS command failed isr[%x]\n", |
| isr); |
| |
| break; |
| } |
| UPDATE_STATS_GB(stst->tcp.xmit_tcp_segs, |
| newstats->xmit_tcp_segs_gb, |
| old->xmit_tcp_segs_gb); |
| |
| UPDATE_STATS_GB(stst->tcp.xmit_tcp_bytes, |
| newstats->xmit_tcp_bytes_gb, |
| old->xmit_tcp_bytes_gb); |
| |
| UPDATE_STATS_GB(stst->tcp.rcv_tcp_segs, |
| newstats->rcv_tcp_segs_gb, |
| old->rcv_tcp_segs_gb); |
| |
| UPDATE_STATS_GB(stst->tcp.rcv_tcp_bytes, |
| newstats->rcv_tcp_bytes_gb, |
| old->rcv_tcp_bytes_gb); |
| |
| UPDATE_STATS_GB(stst->iface.xmt_bytes, |
| newstats->xmit_bytes_gb, |
| old->xmit_bytes_gb); |
| |
| UPDATE_STATS_GB(stst->iface.xmt_ucast, |
| newstats->xmit_unicasts_gb, |
| old->xmit_unicasts_gb); |
| |
| UPDATE_STATS_GB(stst->iface.rcv_bytes, |
| newstats->rcv_bytes_gb, |
| old->rcv_bytes_gb); |
| |
| UPDATE_STATS_GB(stst->iface.rcv_ucast, |
| newstats->rcv_unicasts_gb, |
| old->rcv_unicasts_gb); |
| |
| UPDATE_STATS_GB(stst->iface.xmt_errors, |
| newstats->xmit_collisions_gb, |
| old->xmit_collisions_gb); |
| |
| UPDATE_STATS_GB(stst->iface.xmt_errors, |
| newstats->xmit_excess_collisions_gb, |
| old->xmit_excess_collisions_gb); |
| |
| UPDATE_STATS_GB(stst->iface.xmt_errors, |
| newstats->xmit_other_error_gb, |
| old->xmit_other_error_gb); |
| |
| UPDATE_STATS_GB(stst->iface.rcv_errors, |
| newstats->rcv_other_error_gb, |
| old->rcv_other_error_gb); |
| |
| UPDATE_STATS_GB(stst->iface.rcv_discards, |
| newstats->rcv_drops_gb, |
| old->rcv_drops_gb); |
| |
| if (newstats->rcv_drops_gb > old->rcv_drops_gb) { |
| adapter->rcv_drops += |
| (newstats->rcv_drops_gb - |
| old->rcv_drops_gb); |
| } |
| memcpy(old, newstats, sizeof(struct slic_stats)); |
| break; |
| } |
| case SLIC_UPR_RLSR: |
| slic_link_upr_complete(adapter, isr); |
| break; |
| case SLIC_UPR_RCONFIG: |
| break; |
| case SLIC_UPR_RPHY: |
| ASSERT(0); |
| break; |
| case SLIC_UPR_ENLB: |
| ASSERT(0); |
| break; |
| case SLIC_UPR_ENCT: |
| ASSERT(0); |
| break; |
| case SLIC_UPR_PDWN: |
| ASSERT(0); |
| break; |
| case SLIC_UPR_PING: |
| card->pingstatus |= (isr & ISR_PINGDSMASK); |
| break; |
| default: |
| ASSERT(0); |
| } |
| kfree(upr); |
| slic_upr_start(adapter); |
| spin_unlock_irqrestore(&adapter->upr_lock.lock, |
| adapter->upr_lock.flags); |
| } |
| |
| static void slic_upr_start(struct adapter *adapter) |
| { |
| struct slic_upr *upr; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| /* |
| char * ptr1; |
| char * ptr2; |
| uint cmdoffset; |
| */ |
| upr = adapter->upr_list; |
| if (!upr) |
| return; |
| if (adapter->upr_busy) |
| return; |
| adapter->upr_busy = 1; |
| |
| switch (upr->upr_request) { |
| case SLIC_UPR_STATS: |
| if (upr->upr_data_h == 0) { |
| slic_reg32_write(&slic_regs->slic_stats, upr->upr_data, |
| FLUSH); |
| } else { |
| slic_reg64_write(adapter, &slic_regs->slic_stats64, |
| upr->upr_data, |
| &slic_regs->slic_addr_upper, |
| upr->upr_data_h, FLUSH); |
| } |
| break; |
| |
| case SLIC_UPR_RLSR: |
| slic_reg64_write(adapter, &slic_regs->slic_rlsr, upr->upr_data, |
| &slic_regs->slic_addr_upper, upr->upr_data_h, |
| FLUSH); |
| break; |
| |
| case SLIC_UPR_RCONFIG: |
| slic_reg64_write(adapter, &slic_regs->slic_rconfig, |
| upr->upr_data, &slic_regs->slic_addr_upper, |
| upr->upr_data_h, FLUSH); |
| break; |
| case SLIC_UPR_PING: |
| slic_reg32_write(&slic_regs->slic_ping, 1, FLUSH); |
| break; |
| default: |
| ASSERT(0); |
| } |
| } |
| |
| static void slic_link_upr_complete(struct adapter *adapter, u32 isr) |
| { |
| u32 linkstatus = adapter->pshmem->linkstatus; |
| uint linkup; |
| unsigned char linkspeed; |
| unsigned char linkduplex; |
| |
| if ((isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) { |
| struct slic_shmem *pshmem; |
| |
| pshmem = (struct slic_shmem *)adapter->phys_shmem; |
| #if defined(CONFIG_X86_64) |
| slic_upr_queue_request(adapter, |
| SLIC_UPR_RLSR, |
| SLIC_GET_ADDR_LOW(&pshmem->linkstatus), |
| SLIC_GET_ADDR_HIGH(&pshmem->linkstatus), |
| 0, 0); |
| #elif defined(CONFIG_X86) |
| slic_upr_queue_request(adapter, |
| SLIC_UPR_RLSR, |
| (u32) &pshmem->linkstatus, |
| SLIC_GET_ADDR_HIGH(pshmem), 0, 0); |
| #else |
| Stop Compilation; |
| #endif |
| return; |
| } |
| if (adapter->state != ADAPT_UP) |
| return; |
| |
| ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID) |
| || (adapter->devid == SLIC_2GB_DEVICE_ID)); |
| |
| linkup = linkstatus & GIG_LINKUP ? LINK_UP : LINK_DOWN; |
| if (linkstatus & GIG_SPEED_1000) |
| linkspeed = LINK_1000MB; |
| else if (linkstatus & GIG_SPEED_100) |
| linkspeed = LINK_100MB; |
| else |
| linkspeed = LINK_10MB; |
| |
| if (linkstatus & GIG_FULLDUPLEX) |
| linkduplex = LINK_FULLD; |
| else |
| linkduplex = LINK_HALFD; |
| |
| if ((adapter->linkstate == LINK_DOWN) && (linkup == LINK_DOWN)) |
| return; |
| |
| /* link up event, but nothing has changed */ |
| if ((adapter->linkstate == LINK_UP) && |
| (linkup == LINK_UP) && |
| (adapter->linkspeed == linkspeed) && |
| (adapter->linkduplex == linkduplex)) |
| return; |
| |
| /* link has changed at this point */ |
| |
| /* link has gone from up to down */ |
| if (linkup == LINK_DOWN) { |
| adapter->linkstate = LINK_DOWN; |
| return; |
| } |
| |
| /* link has gone from down to up */ |
| adapter->linkspeed = linkspeed; |
| adapter->linkduplex = linkduplex; |
| |
| if (adapter->linkstate != LINK_UP) { |
| /* setup the mac */ |
| slic_config_set(adapter, true); |
| adapter->linkstate = LINK_UP; |
| netif_start_queue(adapter->netdev); |
| } |
| } |
| |
| /* |
| * this is here to checksum the eeprom, there is some ucode bug |
| * which prevens us from using the ucode result. |
| * remove this once ucode is fixed. |
| */ |
| static ushort slic_eeprom_cksum(char *m, int len) |
| { |
| #define ADDCARRY(x) (x > 65535 ? x -= 65535 : x) |
| #define REDUCE {l_util.l = sum; sum = l_util.s[0] + l_util.s[1]; ADDCARRY(sum);\ |
| } |
| |
| u16 *w; |
| u32 sum = 0; |
| u32 byte_swapped = 0; |
| u32 w_int; |
| |
| union { |
| char c[2]; |
| ushort s; |
| } s_util; |
| |
| union { |
| ushort s[2]; |
| int l; |
| } l_util; |
| |
| l_util.l = 0; |
| s_util.s = 0; |
| |
| w = (u16 *)m; |
| #ifdef CONFIG_X86_64 |
| w_int = (u32) ((ulong) w & 0x00000000FFFFFFFF); |
| #else |
| w_int = (u32) (w); |
| #endif |
| if ((1 & w_int) && (len > 0)) { |
| REDUCE; |
| sum <<= 8; |
| s_util.c[0] = *(unsigned char *)w; |
| w = (u16 *)((char *)w + 1); |
| len--; |
| byte_swapped = 1; |
| } |
| |
| /* Unroll the loop to make overhead from branches &c small. */ |
| while ((len -= 32) >= 0) { |
| sum += w[0]; |
| sum += w[1]; |
| sum += w[2]; |
| sum += w[3]; |
| sum += w[4]; |
| sum += w[5]; |
| sum += w[6]; |
| sum += w[7]; |
| sum += w[8]; |
| sum += w[9]; |
| sum += w[10]; |
| sum += w[11]; |
| sum += w[12]; |
| sum += w[13]; |
| sum += w[14]; |
| sum += w[15]; |
| w = (u16 *)((ulong) w + 16); /* verify */ |
| } |
| len += 32; |
| while ((len -= 8) >= 0) { |
| sum += w[0]; |
| sum += w[1]; |
| sum += w[2]; |
| sum += w[3]; |
| w = (u16 *)((ulong) w + 4); /* verify */ |
| } |
| len += 8; |
| if (len != 0 || byte_swapped != 0) { |
| REDUCE; |
| while ((len -= 2) >= 0) |
| sum += *w++; /* verify */ |
| if (byte_swapped) { |
| REDUCE; |
| sum <<= 8; |
| byte_swapped = 0; |
| if (len == -1) { |
| s_util.c[1] = *(char *) w; |
| sum += s_util.s; |
| len = 0; |
| } else { |
| len = -1; |
| } |
| |
| } else if (len == -1) { |
| s_util.c[0] = *(char *) w; |
| } |
| |
| if (len == -1) { |
| s_util.c[1] = 0; |
| sum += s_util.s; |
| } |
| } |
| REDUCE; |
| return (ushort) sum; |
| } |
| |
| static int slic_rspqueue_init(struct adapter *adapter) |
| { |
| int i; |
| struct slic_rspqueue *rspq = &adapter->rspqueue; |
| __iomem struct slic_regs *slic_regs = adapter->slic_regs; |
| u32 paddrh = 0; |
| |
| ASSERT(adapter->state == ADAPT_DOWN); |
| memset(rspq, 0, sizeof(struct slic_rspqueue)); |
| |
| rspq->num_pages = SLIC_RSPQ_PAGES_GB; |
| |
| for (i = 0; i < rspq->num_pages; i++) { |
| rspq->vaddr[i] = pci_alloc_consistent(adapter->pcidev, |
| PAGE_SIZE, |
| &rspq->paddr[i]); |
| if (!rspq->vaddr[i]) { |
| dev_err(&adapter->pcidev->dev, |
| "pci_alloc_consistent failed\n"); |
| slic_rspqueue_free(adapter); |
| return STATUS_FAILURE; |
| } |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) rspq->vaddr[i] & 0xFFFFF000) == |
| (u32) rspq->vaddr[i]); |
| ASSERT(((u32) rspq->paddr[i] & 0xFFFFF000) == |
| (u32) rspq->paddr[i]); |
| #endif |
| memset(rspq->vaddr[i], 0, PAGE_SIZE); |
| |
| if (paddrh == 0) { |
| slic_reg32_write(&slic_regs->slic_rbar, |
| (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE), |
| DONT_FLUSH); |
| } else { |
| slic_reg64_write(adapter, &slic_regs->slic_rbar64, |
| (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE), |
| &slic_regs->slic_addr_upper, |
| paddrh, DONT_FLUSH); |
| } |
| } |
| rspq->offset = 0; |
| rspq->pageindex = 0; |
| rspq->rspbuf = (struct slic_rspbuf *)rspq->vaddr[0]; |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_rspqueue_free(struct adapter *adapter) |
| { |
| int i; |
| struct slic_rspqueue *rspq = &adapter->rspqueue; |
| |
| for (i = 0; i < rspq->num_pages; i++) { |
| if (rspq->vaddr[i]) { |
| pci_free_consistent(adapter->pcidev, PAGE_SIZE, |
| rspq->vaddr[i], rspq->paddr[i]); |
| } |
| rspq->vaddr[i] = NULL; |
| rspq->paddr[i] = 0; |
| } |
| rspq->offset = 0; |
| rspq->pageindex = 0; |
| rspq->rspbuf = NULL; |
| } |
| |
| static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter) |
| { |
| struct slic_rspqueue *rspq = &adapter->rspqueue; |
| struct slic_rspbuf *buf; |
| |
| if (!(rspq->rspbuf->status)) |
| return NULL; |
| |
| buf = rspq->rspbuf; |
| #ifndef CONFIG_X86_64 |
| ASSERT((buf->status & 0xFFFFFFE0) == 0); |
| #endif |
| ASSERT(buf->hosthandle); |
| if (++rspq->offset < SLIC_RSPQ_BUFSINPAGE) { |
| rspq->rspbuf++; |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) rspq->rspbuf & 0xFFFFFFE0) == |
| (u32) rspq->rspbuf); |
| #endif |
| } else { |
| ASSERT(rspq->offset == SLIC_RSPQ_BUFSINPAGE); |
| slic_reg64_write(adapter, &adapter->slic_regs->slic_rbar64, |
| (rspq->paddr[rspq->pageindex] | SLIC_RSPQ_BUFSINPAGE), |
| &adapter->slic_regs->slic_addr_upper, 0, DONT_FLUSH); |
| rspq->pageindex = (++rspq->pageindex) % rspq->num_pages; |
| rspq->offset = 0; |
| rspq->rspbuf = (struct slic_rspbuf *) |
| rspq->vaddr[rspq->pageindex]; |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) rspq->rspbuf & 0xFFFFF000) == |
| (u32) rspq->rspbuf); |
| #endif |
| } |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) buf & 0xFFFFFFE0) == (u32) buf); |
| #endif |
| return buf; |
| } |
| |
| static void slic_cmdqmem_init(struct adapter *adapter) |
| { |
| struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem; |
| |
| memset(cmdqmem, 0, sizeof(struct slic_cmdqmem)); |
| } |
| |
| static void slic_cmdqmem_free(struct adapter *adapter) |
| { |
| struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem; |
| int i; |
| |
| for (i = 0; i < SLIC_CMDQ_MAXPAGES; i++) { |
| if (cmdqmem->pages[i]) { |
| pci_free_consistent(adapter->pcidev, |
| PAGE_SIZE, |
| (void *) cmdqmem->pages[i], |
| cmdqmem->dma_pages[i]); |
| } |
| } |
| memset(cmdqmem, 0, sizeof(struct slic_cmdqmem)); |
| } |
| |
| static u32 *slic_cmdqmem_addpage(struct adapter *adapter) |
| { |
| struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem; |
| u32 *pageaddr; |
| |
| if (cmdqmem->pagecnt >= SLIC_CMDQ_MAXPAGES) |
| return NULL; |
| pageaddr = pci_alloc_consistent(adapter->pcidev, |
| PAGE_SIZE, |
| &cmdqmem->dma_pages[cmdqmem->pagecnt]); |
| if (!pageaddr) |
| return NULL; |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr); |
| #endif |
| cmdqmem->pages[cmdqmem->pagecnt] = pageaddr; |
| cmdqmem->pagecnt++; |
| return pageaddr; |
| } |
| |
| static int slic_cmdq_init(struct adapter *adapter) |
| { |
| int i; |
| u32 *pageaddr; |
| |
| ASSERT(adapter->state == ADAPT_DOWN); |
| memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue)); |
| memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue)); |
| memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue)); |
| spin_lock_init(&adapter->cmdq_all.lock.lock); |
| spin_lock_init(&adapter->cmdq_free.lock.lock); |
| spin_lock_init(&adapter->cmdq_done.lock.lock); |
| slic_cmdqmem_init(adapter); |
| adapter->slic_handle_ix = 1; |
| for (i = 0; i < SLIC_CMDQ_INITPAGES; i++) { |
| pageaddr = slic_cmdqmem_addpage(adapter); |
| #ifndef CONFIG_X86_64 |
| ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr); |
| #endif |
| if (!pageaddr) { |
| slic_cmdq_free(adapter); |
| return STATUS_FAILURE; |
| } |
| slic_cmdq_addcmdpage(adapter, pageaddr); |
| } |
| adapter->slic_handle_ix = 1; |
| |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_cmdq_free(struct adapter *adapter) |
| { |
| struct slic_hostcmd *cmd; |
| |
| cmd = adapter->cmdq_all.head; |
| while (cmd) { |
| if (cmd->busy) { |
| struct sk_buff *tempskb; |
| |
| tempskb = cmd->skb; |
| if (tempskb) { |
| cmd->skb = NULL; |
| dev_kfree_skb_irq(tempskb); |
| } |
| } |
| cmd = cmd->next_all; |
| } |
| memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue)); |
| memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue)); |
| memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue)); |
| slic_cmdqmem_free(adapter); |
| } |
| |
| static void slic_cmdq_reset(struct adapter *adapter) |
| { |
| struct slic_hostcmd *hcmd; |
| struct sk_buff *skb; |
| u32 outstanding; |
| |
| spin_lock_irqsave(&adapter->cmdq_free.lock.lock, |
| adapter->cmdq_free.lock.flags); |
| spin_lock_irqsave(&adapter->cmdq_done.lock.lock, |
| adapter->cmdq_done.lock.flags); |
| outstanding = adapter->cmdq_all.count - adapter->cmdq_done.count; |
| outstanding -= adapter->cmdq_free.count; |
| hcmd = adapter->cmdq_all.head; |
| while (hcmd) { |
| if (hcmd->busy) { |
| skb = hcmd->skb; |
| ASSERT(skb); |
| hcmd->busy = 0; |
| hcmd->skb = NULL; |
| dev_kfree_skb_irq(skb); |
| } |
| hcmd = hcmd->next_all; |
| } |
| adapter->cmdq_free.count = 0; |
| adapter->cmdq_free.head = NULL; |
| adapter->cmdq_free.tail = NULL; |
| adapter->cmdq_done.count = 0; |
| adapter->cmdq_done.head = NULL; |
| adapter->cmdq_done.tail = NULL; |
| adapter->cmdq_free.head = adapter->cmdq_all.head; |
| hcmd = adapter->cmdq_all.head; |
| while (hcmd) { |
| adapter->cmdq_free.count++; |
| hcmd->next = hcmd->next_all; |
| hcmd = hcmd->next_all; |
| } |
| if (adapter->cmdq_free.count != adapter->cmdq_all.count) { |
| dev_err(&adapter->netdev->dev, |
| "free_count %d != all count %d\n", |
| adapter->cmdq_free.count, adapter->cmdq_all.count); |
| } |
| spin_unlock_irqrestore(&adapter->cmdq_done.lock.lock, |
| adapter->cmdq_done.lock.flags); |
| spin_unlock_irqrestore(&adapter->cmdq_free.lock.lock, |
| adapter->cmdq_free.lock.flags); |
| } |
| |
| static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page) |
| { |
| struct slic_hostcmd *cmd; |
| struct slic_hostcmd *prev; |
| struct slic_hostcmd *tail; |
| struct slic_cmdqueue *cmdq; |
| int cmdcnt; |
| void *cmdaddr; |
| ulong phys_addr; |
| u32 phys_addrl; |
| u32 phys_addrh; |
| struct slic_handle *pslic_handle; |
| |
| cmdaddr = page; |
| cmd = (struct slic_hostcmd *)cmdaddr; |
| cmdcnt = 0; |
| |
| phys_addr = virt_to_bus((void *)page); |
| phys_addrl = SLIC_GET_ADDR_LOW(phys_addr); |
| phys_addrh = SLIC_GET_ADDR_HIGH(phys_addr); |
| |
| prev = NULL; |
| tail = cmd; |
| while ((cmdcnt < SLIC_CMDQ_CMDSINPAGE) && |
| (adapter->slic_handle_ix < 256)) { |
| /* Allocate and initialize a SLIC_HANDLE for this command */ |
| SLIC_GET_SLIC_HANDLE(adapter, pslic_handle); |
| if (pslic_handle == NULL) |
| ASSERT(0); |
| ASSERT(pslic_handle == |
| &adapter->slic_handles[pslic_handle->token. |
| handle_index]); |
| pslic_handle->type = SLIC_HANDLE_CMD; |
| pslic_handle->address = (void *) cmd; |
| pslic_handle->offset = (ushort) adapter->slic_handle_ix++; |
| pslic_handle->other_handle = NULL; |
| pslic_handle->next = NULL; |
| |
| cmd->pslic_handle = pslic_handle; |
| cmd->cmd64.hosthandle = pslic_handle->token.handle_token; |
| cmd->busy = false; |
| cmd->paddrl = phys_addrl; |
| cmd->paddrh = phys_addrh; |
| cmd->next_all = prev; |
| cmd->next = prev; |
| prev = cmd; |
| phys_addrl += SLIC_HOSTCMD_SIZE; |
| cmdaddr += SLIC_HOSTCMD_SIZE; |
| |
| cmd = (struct slic_hostcmd *)cmdaddr; |
| cmdcnt++; |
| } |
| |
| cmdq = &adapter->cmdq_all; |
| cmdq->count += cmdcnt; /* SLIC_CMDQ_CMDSINPAGE; mooktodo */ |
| tail->next_all = cmdq->head; |
| cmdq->head = prev; |
| cmdq = &adapter->cmdq_free; |
| spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags); |
| cmdq->count += cmdcnt; /* SLIC_CMDQ_CMDSINPAGE; mooktodo */ |
| tail->next = cmdq->head; |
| cmdq->head = prev; |
| spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags); |
| } |
| |
| static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter) |
| { |
| struct slic_cmdqueue *cmdq = &adapter->cmdq_free; |
| struct slic_hostcmd *cmd = NULL; |
| |
| lock_and_retry: |
| spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags); |
| retry: |
| cmd = cmdq->head; |
| if (cmd) { |
| cmdq->head = cmd->next; |
| cmdq->count--; |
| spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags); |
| } else { |
| slic_cmdq_getdone(adapter); |
| cmd = cmdq->head; |
| if (cmd) { |
| goto retry; |
| } else { |
| u32 *pageaddr; |
| |
| spin_unlock_irqrestore(&cmdq->lock.lock, |
| cmdq->lock.flags); |
| pageaddr = slic_cmdqmem_addpage(adapter); |
| if (pageaddr) { |
| slic_cmdq_addcmdpage(adapter, pageaddr); |
| goto lock_and_retry; |
| } |
| } |
| } |
| return cmd; |
| } |
| |
| static void slic_cmdq_getdone(struct adapter *adapter) |
| { |
| struct slic_cmdqueue *done_cmdq = &adapter->cmdq_done; |
| struct slic_cmdqueue *free_cmdq = &adapter->cmdq_free; |
| |
| ASSERT(free_cmdq->head == NULL); |
| spin_lock_irqsave(&done_cmdq->lock.lock, done_cmdq->lock.flags); |
| |
| free_cmdq->head = done_cmdq->head; |
| free_cmdq->count = done_cmdq->count; |
| done_cmdq->head = NULL; |
| done_cmdq->tail = NULL; |
| done_cmdq->count = 0; |
| spin_unlock_irqrestore(&done_cmdq->lock.lock, done_cmdq->lock.flags); |
| } |
| |
| static void slic_cmdq_putdone_irq(struct adapter *adapter, |
| struct slic_hostcmd *cmd) |
| { |
| struct slic_cmdqueue *cmdq = &adapter->cmdq_done; |
| |
| spin_lock(&cmdq->lock.lock); |
| cmd->busy = 0; |
| cmd->next = cmdq->head; |
| cmdq->head = cmd; |
| cmdq->count++; |
| if ((adapter->xmitq_full) && (cmdq->count > 10)) |
| netif_wake_queue(adapter->netdev); |
| spin_unlock(&cmdq->lock.lock); |
| } |
| |
| static int slic_rcvqueue_init(struct adapter *adapter) |
| { |
| int i, count; |
| struct slic_rcvqueue *rcvq = &adapter->rcvqueue; |
| |
| ASSERT(adapter->state == ADAPT_DOWN); |
| rcvq->tail = NULL; |
| rcvq->head = NULL; |
| rcvq->size = SLIC_RCVQ_ENTRIES; |
| rcvq->errors = 0; |
| rcvq->count = 0; |
| i = (SLIC_RCVQ_ENTRIES / SLIC_RCVQ_FILLENTRIES); |
| count = 0; |
| while (i) { |
| count += slic_rcvqueue_fill(adapter); |
| i--; |
| } |
| if (rcvq->count < SLIC_RCVQ_MINENTRIES) { |
| slic_rcvqueue_free(adapter); |
| return STATUS_FAILURE; |
| } |
| return STATUS_SUCCESS; |
| } |
| |
| static void slic_rcvqueue_free(struct adapter *adapter) |
| { |
| struct slic_rcvqueue *rcvq = &adapter->rcvqueue; |
| struct sk_buff *skb; |
| |
| while (rcvq->head) { |
| skb = rcvq->head; |
| rcvq->head = rcvq->head->next; |
| dev_kfree_skb(skb); |
| } |
| rcvq->tail = NULL; |
| rcvq->head = NULL; |
| rcvq->count = 0; |
| } |
| |
| static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter) |
| { |
| struct slic_rcvqueue *rcvq = &adapter->rcvqueue; |
| struct sk_buff *skb; |
| struct slic_rcvbuf *rcvbuf; |
| int count; |
| |
| if (rcvq->count) { |
| skb = rcvq->head; |
| rcvbuf = (struct slic_rcvbuf *)skb->head; |
| ASSERT(rcvbuf); |
| |
| if (rcvbuf->status & IRHDDR_SVALID) { |
| rcvq->head = rcvq->head->next; |
| skb->next = NULL; |
| rcvq->count--; |
| } else { |
| skb = NULL; |
| } |
| } else { |
| dev_err(&adapter->netdev->dev, |
| "RcvQ Empty!! rcvq[%p] count[%x]\n", rcvq, rcvq->count); |
| skb = NULL; |
| } |
| while (rcvq->count < SLIC_RCVQ_FILLTHRESH) { |
| count = slic_rcvqueue_fill(adapter); |
| if (!count) |
| break; |
| } |
| if (skb) |
| rcvq->errors = 0; |
| return skb; |
| } |
| |
| static int slic_rcvqueue_fill(struct adapter *adapter) |
| { |
| void *paddr; |
| u32 paddrl; |
| u32 paddrh; |
| struct slic_rcvqueue *rcvq = &adapter->rcvqueue; |
| int i = 0; |
| struct device *dev = &adapter->netdev->dev; |
| |
| while (i < SLIC_RCVQ_FILLENTRIES) { |
| struct slic_rcvbuf *rcvbuf; |
| struct sk_buff *skb; |
| #ifdef KLUDGE_FOR_4GB_BOUNDARY |
| retry_rcvqfill: |
| #endif |
| skb = alloc_skb(SLIC_RCVQ_RCVBUFSIZE, GFP_ATOMIC); |
| if (skb) { |
| paddr = (void *)pci_map_single(adapter->pcidev, |
| skb->data, |
| SLIC_RCVQ_RCVBUFSIZE, |
| PCI_DMA_FROMDEVICE); |
| paddrl = SLIC_GET_ADDR_LOW(paddr); |
| paddrh = SLIC_GET_ADDR_HIGH(paddr); |
| |
| skb->len = SLIC_RCVBUF_HEADSIZE; |
| rcvbuf = (struct slic_rcvbuf *)skb->head; |
| rcvbuf->status = 0; |
| skb->next = NULL; |
| #ifdef KLUDGE_FOR_4GB_BOUNDARY |
| if (paddrl == 0) { |
| dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n", |
| __func__); |
| dev_err(dev, "skb[%p] PROBLEM\n", skb); |
| dev_err(dev, " skbdata[%p]\n", skb->data); |
| dev_err(dev, " skblen[%x]\n", skb->len); |
| dev_err(dev, " paddr[%p]\n", paddr); |
| dev_err(dev, " paddrl[%x]\n", paddrl); |
| dev_err(dev, " paddrh[%x]\n", paddrh); |
| dev_err(dev, " rcvq->head[%p]\n", rcvq->head); |
| dev_err(dev, " rcvq->tail[%p]\n", rcvq->tail); |
| dev_err(dev, " rcvq->count[%x]\n", rcvq->count); |
| dev_err(dev, "SKIP THIS SKB!!!!!!!!\n"); |
| goto retry_rcvqfill; |
| } |
| #else |
| if (paddrl == 0) { |
| dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n", |
| __func__); |
| dev_err(dev, "skb[%p] PROBLEM\n", skb); |
| dev_err(dev, " skbdata[%p]\n", skb->data); |
| dev_err(dev, " skblen[%x]\n", skb->len); |
| dev_err(dev, " paddr[%p]\n", paddr); |
| dev_err(dev, " paddrl[%x]\n", paddrl); |
| dev_err(dev, " paddrh[%x]\n", paddrh); |
| dev_err(dev, " rcvq->head[%p]\n", rcvq->head); |
| dev_err(dev, " rcvq->tail[%p]\n", rcvq->tail); |
| dev_err(dev, " rcvq->count[%x]\n", rcvq->count); |
| dev_err(dev, "GIVE TO CARD ANYWAY\n"); |
| } |
| #endif |
| if (paddrh == 0) { |
| slic_reg32_write(&adapter->slic_regs->slic_hbar, |
| (u32)paddrl, DONT_FLUSH); |
| } else { |
| slic_reg64_write(adapter, |
| &adapter->slic_regs->slic_hbar64, |
| paddrl, |
| &adapter->slic_regs->slic_addr_upper, |
| paddrh, DONT_FLUSH); |
| } |
| if (rcvq->head) |
| rcvq->tail->next = skb; |
| else |
| rcvq->head = skb; |
| rcvq->tail = skb; |
| rcvq->count++; |
| i++; |
| } else { |
| dev_err(&adapter->netdev->dev, |
| "slic_rcvqueue_fill could only get [%d] skbuffs\n", |
| i); |
| break; |
| } |
| } |
| return i; |
| } |
| |
| static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb) |
| { |
| struct slic_rcvqueue *rcvq = &adapter->rcvqueue; |
| void *paddr; |
| u32 paddrl; |
| u32 paddrh; |
| struct slic_rcvbuf *rcvbuf = (struct slic_rcvbuf *)skb->head; |
| struct device *dev; |
| |
| ASSERT(skb->len == SLIC_RCVBUF_HEADSIZE); |
| |
| paddr = (void *)pci_map_single(adapter->pcidev, skb->head, |
| SLIC_RCVQ_RCVBUFSIZE, PCI_DMA_FROMDEVICE); |
| rcvbuf->status = 0; |
| skb->next = NULL; |
| |
| paddrl = SLIC_GET_ADDR_LOW(paddr); |
| paddrh = SLIC_GET_ADDR_HIGH(paddr); |
| |
| if (paddrl == 0) { |
| dev = &adapter->netdev->dev; |
| dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n", |
| __func__); |
| dev_err(dev, "skb[%p] PROBLEM\n", skb); |
| dev_err(dev, " skbdata[%p]\n", skb->data); |
| dev_err(dev, " skblen[%x]\n", skb->len); |
| dev_err(dev, " paddr[%p]\n", paddr); |
| dev_err(dev, " paddrl[%x]\n", paddrl); |
| dev_err(dev, " paddrh[%x]\n", paddrh); |
| dev_err(dev, " rcvq->head[%p]\n", rcvq->head); |
| dev_err(dev, " rcvq->tail[%p]\n", rcvq->tail); |
| dev_err(dev, " rcvq->count[%x]\n", rcvq->count); |
| } |
| if (paddrh == 0) { |
| slic_reg32_write(&adapter->slic_regs->slic_hbar, (u32)paddrl, |
| DONT_FLUSH); |
| } else { |
| slic_reg64_write(adapter, &adapter->slic_regs->slic_hbar64, |
| paddrl, &adapter->slic_regs->slic_addr_upper, |
| paddrh, DONT_FLUSH); |
| } |
| if (rcvq->head) |
| rcvq->tail->next = skb; |
| else |
| rcvq->head = skb; |
| rcvq->tail = skb; |
| rcvq->count++; |
| return rcvq->count; |
| } |
| |
| static int slic_debug_card_show(struct seq_file *seq, void *v) |
| { |
| #ifdef MOOKTODO |
| int i; |
| struct sliccard *card = seq->private; |
| struct slic_config *config = &card->config; |
| unsigned char *fru = (unsigned char *)(&card->config.atk_fru); |
| unsigned char *oemfru = (unsigned char *)(&card->config.OemFru); |
| #endif |
| |
| seq_printf(seq, "driver_version : %s\n", slic_proc_version); |
| seq_printf(seq, "Microcode versions: \n"); |
| seq_printf(seq, " Gigabit (gb) : %s %s\n", |
| MOJAVE_UCODE_VERS_STRING, MOJAVE_UCODE_VERS_DATE); |
| seq_printf(seq, " Gigabit Receiver : %s %s\n", |
| GB_RCVUCODE_VERS_STRING, GB_RCVUCODE_VERS_DATE); |
| seq_printf(seq, "Vendor : %s\n", slic_vendor); |
| seq_printf(seq, "Product Name : %s\n", slic_product_name); |
| #ifdef MOOKTODO |
| seq_printf(seq, "VendorId : %4.4X\n", |
| config->VendorId); |
| seq_printf(seq, "DeviceId : %4.4X\n", |
| config->DeviceId); |
| seq_printf(seq, "RevisionId : %2.2x\n", |
| config->RevisionId); |
| seq_printf(seq, "Bus # : %d\n", card->busnumber); |
| seq_printf(seq, "Device # : %d\n", card->slotnumber); |
| seq_printf(seq, "Interfaces : %d\n", card->card_size); |
| seq_printf(seq, " Initialized : %d\n", |
| card->adapters_activated); |
| seq_printf(seq, " Allocated : %d\n", |
| card->adapters_allocated); |
| ASSERT(card->card_size <= SLIC_NBR_MACS); |
| for (i = 0; i < card->card_size; i++) { |
| seq_printf(seq, |
| " MAC%d : %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", |
| i, config->macinfo[i].macaddrA[0], |
| config->macinfo[i].macaddrA[1], |
| config->macinfo[i].macaddrA[2], |
| config->macinfo[i].macaddrA[3], |
| config->macinfo[i].macaddrA[4], |
| config->macinfo[i].macaddrA[5]); |
| } |
| seq_printf(seq, " IF Init State Duplex/Speed irq\n"); |
| seq_printf(seq, " -------------------------------\n"); |
| for (i = 0; i < card->adapters_allocated; i++) { |
| struct adapter *adapter; |
| |
| adapter = card->adapter[i]; |
| if (adapter) { |
| seq_printf(seq, |
| " %d %d %s %s %s 0x%X\n", |
| adapter->physport, adapter->state, |
| SLIC_LINKSTATE(adapter->linkstate), |
| SLIC_DUPLEX(adapter->linkduplex), |
| SLIC_SPEED(adapter->linkspeed), |
| (uint) adapter->irq); |
| } |
| } |
| seq_printf(seq, "Generation # : %4.4X\n", card->gennumber); |
| seq_printf(seq, "RcvQ max entries : %4.4X\n", |
| SLIC_RCVQ_ENTRIES); |
| seq_printf(seq, "Ping Status : %8.8X\n", |
| card->pingstatus); |
| seq_printf(seq, "Minimum grant : %2.2x\n", |
| config->MinGrant); |
| seq_printf(seq, "Maximum Latency : %2.2x\n", config->MaxLat); |
| seq_printf(seq, "PciStatus : %4.4x\n", |
| config->Pcistatus); |
| seq_printf(seq, "Debug Device Id : %4.4x\n", |
| config->DbgDevId); |
| seq_printf(seq, "DRAM ROM Function : %4.4x\n", |
| config->DramRomFn); |
| seq_printf(seq, "Network interface Pin 1 : %2.2x\n", |
| config->NetIntPin1); |
| seq_printf(seq, "Network interface Pin 2 : %2.2x\n", |
| config->NetIntPin1); |
| seq_printf(seq, "Network interface Pin 3 : %2.2x\n", |
| config->NetIntPin1); |
| seq_printf(seq, "PM capabilities : %4.4X\n", |
| config->PMECapab); |
| seq_printf(seq, "Network Clock Controls : %4.4X\n", |
| config->NwClkCtrls); |
| |
| switch (config->FruFormat) { |
| case ATK_FRU_FORMAT: |
| { |
| seq_printf(seq, |
| "Vendor : Alacritech, Inc.\n"); |
| seq_printf(seq, |
| "Assembly # : %c%c%c%c%c%c\n", |
| fru[0], fru[1], fru[2], fru[3], fru[4], |
| fru[5]); |
| seq_printf(seq, |
| "Revision # : %c%c\n", |
| fru[6], fru[7]); |
| |
| if (config->OEMFruFormat == VENDOR4_FRU_FORMAT) { |
| seq_printf(seq, |
| "Serial # : " |
| "%c%c%c%c%c%c%c%c%c%c%c%c\n", |
| fru[8], fru[9], fru[10], |
| fru[11], fru[12], fru[13], |
| fru[16], fru[17], fru[18], |
| fru[19], fru[20], fru[21]); |
| } else { |
| seq_printf(seq, |
| "Serial # : " |
| "%c%c%c%c%c%c%c%c%c%c%c%c%c%c\n", |
| fru[8], fru[9], fru[10], |
| fru[11], fru[12], fru[13], |
| fru[14], fru[15], fru[16], |
| fru[17], fru[18], fru[19], |
| fru[20], fru[21]); |
| } |
| break; |
| } |
| |
| default: |
| { |
| seq_printf(seq, |
| "Vendor : Alacritech, Inc.\n"); |
| seq_printf(seq, |
| "Serial # : Empty FRU\n"); |
| break; |
| } |
| } |
| |
| switch (config->OEMFruFormat) { |
| case VENDOR1_FRU_FORMAT: |
| { |
| seq_printf(seq, "FRU Information:\n"); |
| seq_printf(seq, " Commodity # : %c\n", |
| oemfru[0]); |
| seq_printf(seq, |
| " Assembly # : %c%c%c%c\n", |
| oemfru[1], oemfru[2], oemfru[3], oemfru[4]); |
| seq_printf(seq, |
| " Revision # : %c%c\n", |
| oemfru[5], oemfru[6]); |
| seq_printf(seq, |
| " Supplier # : %c%c\n", |
| oemfru[7], oemfru[8]); |
| seq_printf(seq, |
| " Date : %c%c\n", |
| oemfru[9], oemfru[10]); |
| seq_sprintf(seq, |
| " Sequence # : %c%c%c\n", |
| oemfru[11], oemfru[12], oemfru[13]); |
| break; |
| } |
| |
| case VENDOR2_FRU_FORMAT: |
| { |
| seq_printf(seq, "FRU Information:\n"); |
| seq_printf(seq, |
| " Part # : " |
| "%c%c%c%c%c%c%c%c\n", |
| oemfru[0], oemfru[1], oemfru[2], |
| oemfru[3], oemfru[4], oemfru[5], |
| oemfru[6], oemfru[7]); |
| seq_printf(seq, |
| " Supplier # : %c%c%c%c%c\n", |
| oemfru[8], oemfru[9], oemfru[10], |
| oemfru[11], oemfru[12]); |
| seq_printf(seq, |
| " Date : %c%c%c\n", |
| oemfru[13], oemfru[14], oemfru[15]); |
| seq_sprintf(seq, |
| " Sequence # : %c%c%c%c\n", |
| oemfru[16], oemfru[17], oemfru[18], |
| oemfru[19]); |
| break; |
| } |
| |
| case VENDOR3_FRU_FORMAT: |
| { |
| seq_printf(seq, "FRU Information:\n"); |
| } |
| |
| case VENDOR4_FRU_FORMAT: |
| { |
| seq_printf(seq, "FRU Information:\n"); |
| seq_printf(seq, |
| " FRU Number : " |
| "%c%c%c%c%c%c%c%c\n", |
| oemfru[0], oemfru[1], oemfru[2], |
| oemfru[3], oemfru[4], oemfru[5], |
| oemfru[6], oemfru[7]); |
| seq_sprintf(seq, |
| " Part Number : " |
| "%c%c%c%c%c%c%c%c\n", |
| oemfru[8], oemfru[9], oemfru[10], |
| oemfru[11], oemfru[12], oemfru[13], |
| oemfru[14], oemfru[15]); |
| seq_printf(seq, |
| " EC Level : " |
| "%c%c%c%c%c%c%c%c\n", |
| oemfru[16], oemfru[17], oemfru[18], |
| oemfru[19], oemfru[20], oemfru[21], |
| oemfru[22], oemfru[23]); |
| break; |
| } |
| |
| default: |
| break; |
| } |
| #endif |
| |
| return 0; |
| } |
| |
| static int slic_debug_adapter_show(struct seq_file *seq, void *v) |
| { |
| struct adapter *adapter = seq->private; |
| |
| if ((adapter->netdev) && (adapter->netdev->name)) { |
| seq_printf(seq, "info: interface : %s\n", |
| adapter->netdev->name); |
| } |
| seq_printf(seq, "info: status : %s\n", |
| SLIC_LINKSTATE(adapter->linkstate)); |
| seq_printf(seq, "info: port : %d\n", |
| adapter->physport); |
| seq_printf(seq, "info: speed : %s\n", |
| SLIC_SPEED(adapter->linkspeed)); |
| seq_printf(seq, "info: duplex : %s\n", |
| SLIC_DUPLEX(adapter->linkduplex)); |
| seq_printf(seq, "info: irq : 0x%X\n", |
| (uint) adapter->irq); |
| seq_printf(seq, "info: Interrupt Agg Delay: %d usec\n", |
| adapter->card->loadlevel_current); |
| seq_printf(seq, "info: RcvQ max entries : %4.4X\n", |
| SLIC_RCVQ_ENTRIES); |
| seq_printf(seq, "info: RcvQ current : %4.4X\n", |
| adapter->rcvqueue.count); |
| seq_printf(seq, "rx stats: packets : %8.8lX\n", |
| adapter->stats.rx_packets); |
| seq_printf(seq, "rx stats: bytes : %8.8lX\n", |
| adapter->stats.rx_bytes); |
| seq_printf(seq, "rx stats: broadcasts : %8.8X\n", |
| adapter->rcv_broadcasts); |
| seq_printf(seq, "rx stats: multicasts : %8.8X\n", |
| adapter->rcv_multicasts); |
| seq_printf(seq, "rx stats: unicasts : %8.8X\n", |
| adapter->rcv_unicasts); |
| seq_printf(seq, "rx stats: errors : %8.8X\n", |
| (u32) adapter->slic_stats.iface.rcv_errors); |
| seq_printf(seq, "rx stats: Missed errors : %8.8X\n", |
| (u32) adapter->slic_stats.iface.rcv_discards); |
| seq_printf(seq, "rx stats: drops : %8.8X\n", |
| (u32) adapter->rcv_drops); |
| seq_printf(seq, "tx stats: packets : %8.8lX\n", |
| adapter->stats.tx_packets); |
| seq_printf(seq, "tx stats: bytes : %8.8lX\n", |
| adapter->stats.tx_bytes); |
| seq_printf(seq, "tx stats: errors : %8.8X\n", |
| (u32) adapter->slic_stats.iface.xmt_errors); |
| seq_printf(seq, "rx stats: multicasts : %8.8lX\n", |
| adapter->stats.multicast); |
| seq_printf(seq, "tx stats: collision errors : %8.8X\n", |
| (u32) adapter->slic_stats.iface.xmit_collisions); |
| seq_printf(seq, "perf: Max rcv frames/isr : %8.8X\n", |
| adapter->max_isr_rcvs); |
| seq_printf(seq, "perf: Rcv interrupt yields : %8.8X\n", |
| adapter->rcv_interrupt_yields); |
| seq_printf(seq, "perf: Max xmit complete/isr : %8.8X\n", |
| adapter->max_isr_xmits); |
| seq_printf(seq, "perf: error interrupts : %8.8X\n", |
| adapter->error_interrupts); |
| seq_printf(seq, "perf: error rmiss interrupts : %8.8X\n", |
| adapter->error_rmiss_interrupts); |
| seq_printf(seq, "perf: rcv interrupts : %8.8X\n", |
| adapter->rcv_interrupts); |
| seq_printf(seq, "perf: xmit interrupts : %8.8X\n", |
| adapter->xmit_interrupts); |
| seq_printf(seq, "perf: link event interrupts : %8.8X\n", |
| adapter->linkevent_interrupts); |
| seq_printf(seq, "perf: UPR interrupts : %8.8X\n", |
| adapter->upr_interrupts); |
| seq_printf(seq, "perf: interrupt count : %8.8X\n", |
| adapter->num_isrs); |
| seq_printf(seq, "perf: false interrupts : %8.8X\n", |
| adapter->false_interrupts); |
| seq_printf(seq, "perf: All register writes : %8.8X\n", |
| adapter->all_reg_writes); |
| seq_printf(seq, "perf: ICR register writes : %8.8X\n", |
| adapter->icr_reg_writes); |
| seq_printf(seq, "perf: ISR register writes : %8.8X\n", |
| adapter->isr_reg_writes); |
| seq_printf(seq, "ifevents: overflow 802 errors : %8.8X\n", |
| adapter->if_events.oflow802); |
| seq_printf(seq, "ifevents: transport overflow errors: %8.8X\n", |
| adapter->if_events.Tprtoflow); |
| seq_printf(seq, "ifevents: underflow errors : %8.8X\n", |
| adapter->if_events.uflow802); |
| seq_printf(seq, "ifevents: receive early : %8.8X\n", |
| adapter->if_events.rcvearly); |
| seq_printf(seq, "ifevents: buffer overflows : %8.8X\n", |
| adapter->if_events.Bufov); |
| seq_printf(seq, "ifevents: carrier errors : %8.8X\n", |
| adapter->if_events.Carre); |
| seq_printf(seq, "ifevents: Long : %8.8X\n", |
| adapter->if_events.Longe); |
| seq_printf(seq, "ifevents: invalid preambles : %8.8X\n", |
| adapter->if_events.Invp); |
| seq_printf(seq, "ifevents: CRC errors : %8.8X\n", |
| adapter->if_events.Crc); |
| seq_printf(seq, "ifevents: dribble nibbles : %8.8X\n", |
| adapter->if_events.Drbl); |
| seq_printf(seq, "ifevents: Code violations : %8.8X\n", |
| adapter->if_events.Code); |
| seq_printf(seq, "ifevents: TCP checksum errors : %8.8X\n", |
| adapter->if_events.TpCsum); |
| seq_printf(seq, "ifevents: TCP header short errors : %8.8X\n", |
| adapter->if_events.TpHlen); |
| seq_printf(seq, "ifevents: IP checksum errors : %8.8X\n", |
| adapter->if_events.IpCsum); |
| seq_printf(seq, "ifevents: IP frame incompletes : %8.8X\n", |
| adapter->if_events.IpLen); |
| seq_printf(seq, "ifevents: IP headers shorts : %8.8X\n", |
| adapter->if_events.IpHlen); |
| |
| return 0; |
| } |
| static int slic_debug_adapter_open(struct inode *inode, struct file *file) |
| { |
| return single_open(file, slic_debug_adapter_show, inode->i_private); |
| } |
| |
| static int slic_debug_card_open(struct inode *inode, struct file *file) |
| { |
| return single_open(file, slic_debug_card_show, inode->i_private); |
| } |
| |
| static const struct file_operations slic_debug_adapter_fops = { |
| .owner = THIS_MODULE, |
| .open = slic_debug_adapter_open, |
| .read = seq_read, |
| .llseek = seq_lseek, |
| .release = single_release, |
| }; |
| |
| static const struct file_operations slic_debug_card_fops = { |
| .owner = THIS_MODULE, |
| .open = slic_debug_card_open, |
| .read = seq_read, |
| .llseek = seq_lseek, |
| .release = single_release, |
| }; |
| |
| static void slic_debug_adapter_create(struct adapter *adapter) |
| { |
| struct dentry *d; |
| char name[7]; |
| struct sliccard *card = adapter->card; |
| |
| if (!card->debugfs_dir) |
| return; |
| |
| sprintf(name, "port%d", adapter->port); |
| d = debugfs_create_file(name, S_IRUGO, |
| card->debugfs_dir, adapter, |
| &slic_debug_adapter_fops); |
| if (!d || IS_ERR(d)) |
| pr_info(PFX "%s: debugfs create failed\n", name); |
| else |
| adapter->debugfs_entry = d; |
| } |
| |
| static void slic_debug_adapter_destroy(struct adapter *adapter) |
| { |
| if (adapter->debugfs_entry) { |
| debugfs_remove(adapter->debugfs_entry); |
| adapter->debugfs_entry = NULL; |
| } |
| } |
| |
| static void slic_debug_card_create(struct sliccard *card) |
| { |
| struct dentry *d; |
| char name[IFNAMSIZ]; |
| |
| snprintf(name, sizeof(name), "slic%d", card->cardnum); |
| d = debugfs_create_dir(name, slic_debugfs); |
| if (!d || IS_ERR(d)) |
| pr_info(PFX "%s: debugfs create dir failed\n", |
| name); |
| else { |
| card->debugfs_dir = d; |
| d = debugfs_create_file("cardinfo", S_IRUGO, |
| slic_debugfs, card, |
| &slic_debug_card_fops); |
| if (!d || IS_ERR(d)) |
| pr_info(PFX "%s: debugfs create failed\n", |
| name); |
| else |
| card->debugfs_cardinfo = d; |
| } |
| } |
| |
| static void slic_debug_card_destroy(struct sliccard *card) |
| { |
| int i; |
| |
| for (i = 0; i < card->card_size; i++) { |
| struct adapter *adapter; |
| |
| adapter = card->adapter[i]; |
| if (adapter) |
| slic_debug_adapter_destroy(adapter); |
| } |
| if (card->debugfs_cardinfo) { |
| debugfs_remove(card->debugfs_cardinfo); |
| card->debugfs_cardinfo = NULL; |
| } |
| if (card->debugfs_dir) { |
| debugfs_remove(card->debugfs_dir); |
| card->debugfs_dir = NULL; |
| } |
| } |
| |
| static void slic_debug_init(void) |
| { |
| struct dentry *ent; |
| |
| ent = debugfs_create_dir("slic", NULL); |
| if (!ent || IS_ERR(ent)) { |
| pr_info(PFX "debugfs create directory failed\n"); |
| return; |
| } |
| |
| slic_debugfs = ent; |
| } |
| |
| static void slic_debug_cleanup(void) |
| { |
| if (slic_debugfs) { |
| debugfs_remove(slic_debugfs); |
| slic_debugfs = NULL; |
| } |
| } |
| |
| /******************************************************************************/ |
| /**************** MODULE INITIATION / TERMINATION FUNCTIONS ***************/ |
| /******************************************************************************/ |
| |
| static struct pci_driver slic_driver = { |
| .name = DRV_NAME, |
| .id_table = slic_pci_tbl, |
| .probe = slic_entry_probe, |
| .remove = slic_entry_remove, |
| }; |
| |
| static int __init slic_module_init(void) |
| { |
| slic_init_driver(); |
| |
| if (debug >= 0 && slic_debug != debug) |
| printk(KERN_DEBUG KBUILD_MODNAME ": debug level is %d.\n", |
| debug); |
| if (debug >= 0) |
| slic_debug = debug; |
| |
| return pci_register_driver(&slic_driver); |
| } |
| |
| static void __exit slic_module_cleanup(void) |
| { |
| pci_unregister_driver(&slic_driver); |
| slic_debug_cleanup(); |
| } |
| |
| module_init(slic_module_init); |
| module_exit(slic_module_cleanup); |