| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX |
| |
| maintainers: |
| - Shawn Guo <shawnguo@kernel.org> |
| |
| allOf: |
| - $ref: sdhci-common.yaml# |
| |
| description: | |
| The Enhanced Secure Digital Host Controller on Freescale i.MX family |
| provides an interface for MMC, SD, and SDIO types of memory cards. |
| |
| This file documents differences between the core properties described |
| by mmc.txt and the properties used by the sdhci-esdhc-imx driver. |
| |
| properties: |
| compatible: |
| oneOf: |
| - enum: |
| - fsl,imx25-esdhc |
| - fsl,imx35-esdhc |
| - fsl,imx51-esdhc |
| - fsl,imx53-esdhc |
| - fsl,imx6q-usdhc |
| - fsl,imx6sl-usdhc |
| - fsl,imx6sx-usdhc |
| - fsl,imx7d-usdhc |
| - fsl,imx7ulp-usdhc |
| - fsl,imx8mm-usdhc |
| - fsl,imxrt1050-usdhc |
| - nxp,s32g2-usdhc |
| - items: |
| - const: fsl,imx50-esdhc |
| - const: fsl,imx53-esdhc |
| - items: |
| - enum: |
| - fsl,imx6sll-usdhc |
| - fsl,imx6ull-usdhc |
| - fsl,imx6ul-usdhc |
| - const: fsl,imx6sx-usdhc |
| - items: |
| - const: fsl,imx7d-usdhc |
| - const: fsl,imx6sl-usdhc |
| - items: |
| - enum: |
| - fsl,imx8mq-usdhc |
| - const: fsl,imx7d-usdhc |
| - items: |
| - enum: |
| - fsl,imx8mn-usdhc |
| - fsl,imx8mp-usdhc |
| - fsl,imx8ulp-usdhc |
| - fsl,imx93-usdhc |
| - fsl,imx95-usdhc |
| - const: fsl,imx8mm-usdhc |
| - items: |
| - enum: |
| - fsl,imx8dxl-usdhc |
| - fsl,imx8qm-usdhc |
| - const: fsl,imx8qxp-usdhc |
| - items: |
| - enum: |
| - fsl,imx8mm-usdhc |
| - fsl,imx8mn-usdhc |
| - fsl,imx8mp-usdhc |
| - fsl,imx8qm-usdhc |
| - fsl,imx8qxp-usdhc |
| - const: fsl,imx7d-usdhc |
| deprecated: true |
| - items: |
| - enum: |
| - fsl,imx8mn-usdhc |
| - fsl,imx8mp-usdhc |
| - const: fsl,imx8mm-usdhc |
| - const: fsl,imx7d-usdhc |
| deprecated: true |
| - items: |
| - enum: |
| - fsl,imx8dxl-usdhc |
| - fsl,imx8qm-usdhc |
| - const: fsl,imx8qxp-usdhc |
| - const: fsl,imx7d-usdhc |
| deprecated: true |
| - items: |
| - enum: |
| - fsl,imxrt1170-usdhc |
| - const: fsl,imxrt1050-usdhc |
| |
| reg: |
| maxItems: 1 |
| |
| interrupts: |
| maxItems: 1 |
| |
| fsl,wp-controller: |
| description: | |
| boolean, if present, indicate to use controller internal write protection. |
| type: boolean |
| |
| fsl,delay-line: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: | |
| Specify the number of delay cells for override mode. |
| This is used to set the clock delay for DLL(Delay Line) on override mode |
| to select a proper data sampling window in case the clock quality is not good |
| because the signal path is too long on the board. Please refer to eSDHC/uSDHC |
| chapter, DLL (Delay Line) section in RM for details. |
| default: 0 |
| |
| voltage-ranges: |
| $ref: /schemas/types.yaml#/definitions/uint32-matrix |
| description: | |
| Specify the voltage range in case there are software transparent level |
| shifters on the outputs of the controller. Two cells are required, first |
| cell specifies minimum slot voltage (mV), second cell specifies maximum |
| slot voltage (mV). |
| items: |
| items: |
| - description: value for minimum slot voltage |
| - description: value for maximum slot voltage |
| maxItems: 1 |
| |
| fsl,tuning-start-tap: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: | |
| Specify the start delay cell point when send first CMD19 in tuning procedure. |
| default: 0 |
| |
| fsl,tuning-step: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: | |
| Specify the increasing delay cell steps in tuning procedure. |
| The uSDHC use one delay cell as default increasing step to do tuning process. |
| This property allows user to change the tuning step to more than one delay |
| cell which is useful for some special boards or cards when the default |
| tuning step can't find the proper delay window within limited tuning retries. |
| default: 0 |
| |
| fsl,strobe-dll-delay-target: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: | |
| Specify the strobe dll control slave delay target. |
| This delay target programming host controller loopback read clock, and this |
| property allows user to change the delay target for the strobe input read clock. |
| If not use this property, driver default set the delay target to value 7. |
| Only eMMC HS400 mode need to take care of this property. |
| default: 0 |
| |
| clocks: |
| maxItems: 3 |
| description: |
| Handle clocks for the sdhc controller. |
| |
| clock-names: |
| items: |
| - const: ipg |
| - const: ahb |
| - const: per |
| |
| iommus: |
| maxItems: 1 |
| |
| power-domains: |
| maxItems: 1 |
| |
| pinctrl-names: |
| oneOf: |
| - minItems: 3 |
| items: |
| - const: default |
| - const: state_100mhz |
| - const: state_200mhz |
| - const: sleep |
| - minItems: 2 |
| items: |
| - const: default |
| - const: state_100mhz |
| - const: sleep |
| - minItems: 1 |
| items: |
| - const: default |
| - const: sleep |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| |
| unevaluatedProperties: false |
| |
| examples: |
| - | |
| mmc@70004000 { |
| compatible = "fsl,imx51-esdhc"; |
| reg = <0x70004000 0x4000>; |
| interrupts = <1>; |
| fsl,wp-controller; |
| }; |
| |
| mmc@70008000 { |
| compatible = "fsl,imx51-esdhc"; |
| reg = <0x70008000 0x4000>; |
| interrupts = <2>; |
| cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */ |
| wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */ |
| }; |
