| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2003-2022, Intel Corporation. All rights reserved. |
| * Intel Management Engine Interface (Intel MEI) Linux driver |
| */ |
| |
| #include <linux/pci.h> |
| |
| #include <linux/kthread.h> |
| #include <linux/interrupt.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/sizes.h> |
| #include <linux/delay.h> |
| |
| #include "mei_dev.h" |
| #include "hbm.h" |
| |
| #include "hw-me.h" |
| #include "hw-me-regs.h" |
| |
| #include "mei-trace.h" |
| |
| /** |
| * mei_me_reg_read - Reads 32bit data from the mei device |
| * |
| * @hw: the me hardware structure |
| * @offset: offset from which to read the data |
| * |
| * Return: register value (u32) |
| */ |
| static inline u32 mei_me_reg_read(const struct mei_me_hw *hw, |
| unsigned long offset) |
| { |
| return ioread32(hw->mem_addr + offset); |
| } |
| |
| |
| /** |
| * mei_me_reg_write - Writes 32bit data to the mei device |
| * |
| * @hw: the me hardware structure |
| * @offset: offset from which to write the data |
| * @value: register value to write (u32) |
| */ |
| static inline void mei_me_reg_write(const struct mei_me_hw *hw, |
| unsigned long offset, u32 value) |
| { |
| iowrite32(value, hw->mem_addr + offset); |
| } |
| |
| /** |
| * mei_me_mecbrw_read - Reads 32bit data from ME circular buffer |
| * read window register |
| * |
| * @dev: the device structure |
| * |
| * Return: ME_CB_RW register value (u32) |
| */ |
| static inline u32 mei_me_mecbrw_read(const struct mei_device *dev) |
| { |
| return mei_me_reg_read(to_me_hw(dev), ME_CB_RW); |
| } |
| |
| /** |
| * mei_me_hcbww_write - write 32bit data to the host circular buffer |
| * |
| * @dev: the device structure |
| * @data: 32bit data to be written to the host circular buffer |
| */ |
| static inline void mei_me_hcbww_write(struct mei_device *dev, u32 data) |
| { |
| mei_me_reg_write(to_me_hw(dev), H_CB_WW, data); |
| } |
| |
| /** |
| * mei_me_mecsr_read - Reads 32bit data from the ME CSR |
| * |
| * @dev: the device structure |
| * |
| * Return: ME_CSR_HA register value (u32) |
| */ |
| static inline u32 mei_me_mecsr_read(const struct mei_device *dev) |
| { |
| u32 reg; |
| |
| reg = mei_me_reg_read(to_me_hw(dev), ME_CSR_HA); |
| trace_mei_reg_read(dev->dev, "ME_CSR_HA", ME_CSR_HA, reg); |
| |
| return reg; |
| } |
| |
| /** |
| * mei_hcsr_read - Reads 32bit data from the host CSR |
| * |
| * @dev: the device structure |
| * |
| * Return: H_CSR register value (u32) |
| */ |
| static inline u32 mei_hcsr_read(const struct mei_device *dev) |
| { |
| u32 reg; |
| |
| reg = mei_me_reg_read(to_me_hw(dev), H_CSR); |
| trace_mei_reg_read(dev->dev, "H_CSR", H_CSR, reg); |
| |
| return reg; |
| } |
| |
| /** |
| * mei_hcsr_write - writes H_CSR register to the mei device |
| * |
| * @dev: the device structure |
| * @reg: new register value |
| */ |
| static inline void mei_hcsr_write(struct mei_device *dev, u32 reg) |
| { |
| trace_mei_reg_write(dev->dev, "H_CSR", H_CSR, reg); |
| mei_me_reg_write(to_me_hw(dev), H_CSR, reg); |
| } |
| |
| /** |
| * mei_hcsr_set - writes H_CSR register to the mei device, |
| * and ignores the H_IS bit for it is write-one-to-zero. |
| * |
| * @dev: the device structure |
| * @reg: new register value |
| */ |
| static inline void mei_hcsr_set(struct mei_device *dev, u32 reg) |
| { |
| reg &= ~H_CSR_IS_MASK; |
| mei_hcsr_write(dev, reg); |
| } |
| |
| /** |
| * mei_hcsr_set_hig - set host interrupt (set H_IG) |
| * |
| * @dev: the device structure |
| */ |
| static inline void mei_hcsr_set_hig(struct mei_device *dev) |
| { |
| u32 hcsr; |
| |
| hcsr = mei_hcsr_read(dev) | H_IG; |
| mei_hcsr_set(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_d0i3c_read - Reads 32bit data from the D0I3C register |
| * |
| * @dev: the device structure |
| * |
| * Return: H_D0I3C register value (u32) |
| */ |
| static inline u32 mei_me_d0i3c_read(const struct mei_device *dev) |
| { |
| u32 reg; |
| |
| reg = mei_me_reg_read(to_me_hw(dev), H_D0I3C); |
| trace_mei_reg_read(dev->dev, "H_D0I3C", H_D0I3C, reg); |
| |
| return reg; |
| } |
| |
| /** |
| * mei_me_d0i3c_write - writes H_D0I3C register to device |
| * |
| * @dev: the device structure |
| * @reg: new register value |
| */ |
| static inline void mei_me_d0i3c_write(struct mei_device *dev, u32 reg) |
| { |
| trace_mei_reg_write(dev->dev, "H_D0I3C", H_D0I3C, reg); |
| mei_me_reg_write(to_me_hw(dev), H_D0I3C, reg); |
| } |
| |
| /** |
| * mei_me_trc_status - read trc status register |
| * |
| * @dev: mei device |
| * @trc: trc status register value |
| * |
| * Return: 0 on success, error otherwise |
| */ |
| static int mei_me_trc_status(struct mei_device *dev, u32 *trc) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (!hw->cfg->hw_trc_supported) |
| return -EOPNOTSUPP; |
| |
| *trc = mei_me_reg_read(hw, ME_TRC); |
| trace_mei_reg_read(dev->dev, "ME_TRC", ME_TRC, *trc); |
| |
| return 0; |
| } |
| |
| /** |
| * mei_me_fw_status - read fw status register from pci config space |
| * |
| * @dev: mei device |
| * @fw_status: fw status register values |
| * |
| * Return: 0 on success, error otherwise |
| */ |
| static int mei_me_fw_status(struct mei_device *dev, |
| struct mei_fw_status *fw_status) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| const struct mei_fw_status *fw_src = &hw->cfg->fw_status; |
| int ret; |
| int i; |
| |
| if (!fw_status || !hw->read_fws) |
| return -EINVAL; |
| |
| fw_status->count = fw_src->count; |
| for (i = 0; i < fw_src->count && i < MEI_FW_STATUS_MAX; i++) { |
| ret = hw->read_fws(dev, fw_src->status[i], |
| &fw_status->status[i]); |
| trace_mei_pci_cfg_read(dev->dev, "PCI_CFG_HFS_X", |
| fw_src->status[i], |
| fw_status->status[i]); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * mei_me_hw_config - configure hw dependent settings |
| * |
| * @dev: mei device |
| * |
| * Return: |
| * * -EINVAL when read_fws is not set |
| * * 0 on success |
| * |
| */ |
| static int mei_me_hw_config(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 hcsr, reg; |
| |
| if (WARN_ON(!hw->read_fws)) |
| return -EINVAL; |
| |
| /* Doesn't change in runtime */ |
| hcsr = mei_hcsr_read(dev); |
| hw->hbuf_depth = (hcsr & H_CBD) >> 24; |
| |
| reg = 0; |
| hw->read_fws(dev, PCI_CFG_HFS_1, ®); |
| trace_mei_pci_cfg_read(dev->dev, "PCI_CFG_HFS_1", PCI_CFG_HFS_1, reg); |
| hw->d0i3_supported = |
| ((reg & PCI_CFG_HFS_1_D0I3_MSK) == PCI_CFG_HFS_1_D0I3_MSK); |
| |
| hw->pg_state = MEI_PG_OFF; |
| if (hw->d0i3_supported) { |
| reg = mei_me_d0i3c_read(dev); |
| if (reg & H_D0I3C_I3) |
| hw->pg_state = MEI_PG_ON; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * mei_me_pg_state - translate internal pg state |
| * to the mei power gating state |
| * |
| * @dev: mei device |
| * |
| * Return: MEI_PG_OFF if aliveness is on and MEI_PG_ON otherwise |
| */ |
| static inline enum mei_pg_state mei_me_pg_state(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| return hw->pg_state; |
| } |
| |
| static inline u32 me_intr_src(u32 hcsr) |
| { |
| return hcsr & H_CSR_IS_MASK; |
| } |
| |
| /** |
| * me_intr_disable - disables mei device interrupts |
| * using supplied hcsr register value. |
| * |
| * @dev: the device structure |
| * @hcsr: supplied hcsr register value |
| */ |
| static inline void me_intr_disable(struct mei_device *dev, u32 hcsr) |
| { |
| hcsr &= ~H_CSR_IE_MASK; |
| mei_hcsr_set(dev, hcsr); |
| } |
| |
| /** |
| * me_intr_clear - clear and stop interrupts |
| * |
| * @dev: the device structure |
| * @hcsr: supplied hcsr register value |
| */ |
| static inline void me_intr_clear(struct mei_device *dev, u32 hcsr) |
| { |
| if (me_intr_src(hcsr)) |
| mei_hcsr_write(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_intr_clear - clear and stop interrupts |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_intr_clear(struct mei_device *dev) |
| { |
| u32 hcsr = mei_hcsr_read(dev); |
| |
| me_intr_clear(dev, hcsr); |
| } |
| /** |
| * mei_me_intr_enable - enables mei device interrupts |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_intr_enable(struct mei_device *dev) |
| { |
| u32 hcsr; |
| |
| if (mei_me_hw_use_polling(to_me_hw(dev))) |
| return; |
| |
| hcsr = mei_hcsr_read(dev) | H_CSR_IE_MASK; |
| mei_hcsr_set(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_intr_disable - disables mei device interrupts |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_intr_disable(struct mei_device *dev) |
| { |
| u32 hcsr = mei_hcsr_read(dev); |
| |
| me_intr_disable(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_synchronize_irq - wait for pending IRQ handlers |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_synchronize_irq(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (mei_me_hw_use_polling(hw)) |
| return; |
| |
| synchronize_irq(hw->irq); |
| } |
| |
| /** |
| * mei_me_hw_reset_release - release device from the reset |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_hw_reset_release(struct mei_device *dev) |
| { |
| u32 hcsr = mei_hcsr_read(dev); |
| |
| hcsr |= H_IG; |
| hcsr &= ~H_RST; |
| mei_hcsr_set(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_host_set_ready - enable device |
| * |
| * @dev: mei device |
| */ |
| static void mei_me_host_set_ready(struct mei_device *dev) |
| { |
| u32 hcsr = mei_hcsr_read(dev); |
| |
| if (!mei_me_hw_use_polling(to_me_hw(dev))) |
| hcsr |= H_CSR_IE_MASK; |
| |
| hcsr |= H_IG | H_RDY; |
| mei_hcsr_set(dev, hcsr); |
| } |
| |
| /** |
| * mei_me_host_is_ready - check whether the host has turned ready |
| * |
| * @dev: mei device |
| * Return: bool |
| */ |
| static bool mei_me_host_is_ready(struct mei_device *dev) |
| { |
| u32 hcsr = mei_hcsr_read(dev); |
| |
| return (hcsr & H_RDY) == H_RDY; |
| } |
| |
| /** |
| * mei_me_hw_is_ready - check whether the me(hw) has turned ready |
| * |
| * @dev: mei device |
| * Return: bool |
| */ |
| static bool mei_me_hw_is_ready(struct mei_device *dev) |
| { |
| u32 mecsr = mei_me_mecsr_read(dev); |
| |
| return (mecsr & ME_RDY_HRA) == ME_RDY_HRA; |
| } |
| |
| /** |
| * mei_me_hw_is_resetting - check whether the me(hw) is in reset |
| * |
| * @dev: mei device |
| * Return: bool |
| */ |
| static bool mei_me_hw_is_resetting(struct mei_device *dev) |
| { |
| u32 mecsr = mei_me_mecsr_read(dev); |
| |
| return (mecsr & ME_RST_HRA) == ME_RST_HRA; |
| } |
| |
| /** |
| * mei_gsc_pxp_check - check for gsc firmware entering pxp mode |
| * |
| * @dev: the device structure |
| */ |
| static void mei_gsc_pxp_check(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 fwsts5 = 0; |
| |
| if (!kind_is_gsc(dev) && !kind_is_gscfi(dev)) |
| return; |
| |
| hw->read_fws(dev, PCI_CFG_HFS_5, &fwsts5); |
| trace_mei_pci_cfg_read(dev->dev, "PCI_CFG_HFS_5", PCI_CFG_HFS_5, fwsts5); |
| |
| if ((fwsts5 & GSC_CFG_HFS_5_BOOT_TYPE_MSK) == GSC_CFG_HFS_5_BOOT_TYPE_PXP) { |
| if (dev->gsc_reset_to_pxp == MEI_DEV_RESET_TO_PXP_DEFAULT) |
| dev->gsc_reset_to_pxp = MEI_DEV_RESET_TO_PXP_PERFORMED; |
| } else { |
| dev->gsc_reset_to_pxp = MEI_DEV_RESET_TO_PXP_DEFAULT; |
| } |
| |
| if (dev->pxp_mode == MEI_DEV_PXP_DEFAULT) |
| return; |
| |
| if ((fwsts5 & GSC_CFG_HFS_5_BOOT_TYPE_MSK) == GSC_CFG_HFS_5_BOOT_TYPE_PXP) { |
| dev_dbg(dev->dev, "pxp mode is ready 0x%08x\n", fwsts5); |
| dev->pxp_mode = MEI_DEV_PXP_READY; |
| } else { |
| dev_dbg(dev->dev, "pxp mode is not ready 0x%08x\n", fwsts5); |
| } |
| } |
| |
| /** |
| * mei_me_hw_ready_wait - wait until the me(hw) has turned ready |
| * or timeout is reached |
| * |
| * @dev: mei device |
| * Return: 0 on success, error otherwise |
| */ |
| static int mei_me_hw_ready_wait(struct mei_device *dev) |
| { |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_hw_ready, |
| dev->recvd_hw_ready, |
| dev->timeouts.hw_ready); |
| mutex_lock(&dev->device_lock); |
| if (!dev->recvd_hw_ready) { |
| dev_err(dev->dev, "wait hw ready failed\n"); |
| return -ETIME; |
| } |
| |
| mei_gsc_pxp_check(dev); |
| |
| mei_me_hw_reset_release(dev); |
| dev->recvd_hw_ready = false; |
| return 0; |
| } |
| |
| /** |
| * mei_me_check_fw_reset - check for the firmware reset error and exception conditions |
| * |
| * @dev: mei device |
| */ |
| static void mei_me_check_fw_reset(struct mei_device *dev) |
| { |
| struct mei_fw_status fw_status; |
| char fw_sts_str[MEI_FW_STATUS_STR_SZ] = {0}; |
| int ret; |
| u32 fw_pm_event = 0; |
| |
| if (!dev->saved_fw_status_flag) |
| goto end; |
| |
| if (dev->gsc_reset_to_pxp == MEI_DEV_RESET_TO_PXP_PERFORMED) { |
| ret = mei_fw_status(dev, &fw_status); |
| if (!ret) { |
| fw_pm_event = fw_status.status[1] & PCI_CFG_HFS_2_PM_EVENT_MASK; |
| if (fw_pm_event != PCI_CFG_HFS_2_PM_CMOFF_TO_CMX_ERROR && |
| fw_pm_event != PCI_CFG_HFS_2_PM_CM_RESET_ERROR) |
| goto end; |
| } else { |
| dev_err(dev->dev, "failed to read firmware status: %d\n", ret); |
| } |
| } |
| |
| mei_fw_status2str(&dev->saved_fw_status, fw_sts_str, sizeof(fw_sts_str)); |
| dev_warn(dev->dev, "unexpected reset: fw_pm_event = 0x%x, dev_state = %u fw status = %s\n", |
| fw_pm_event, dev->saved_dev_state, fw_sts_str); |
| |
| end: |
| if (dev->gsc_reset_to_pxp == MEI_DEV_RESET_TO_PXP_PERFORMED) |
| dev->gsc_reset_to_pxp = MEI_DEV_RESET_TO_PXP_DONE; |
| dev->saved_fw_status_flag = false; |
| } |
| |
| /** |
| * mei_me_hw_start - hw start routine |
| * |
| * @dev: mei device |
| * Return: 0 on success, error otherwise |
| */ |
| static int mei_me_hw_start(struct mei_device *dev) |
| { |
| int ret = mei_me_hw_ready_wait(dev); |
| |
| if (kind_is_gsc(dev) || kind_is_gscfi(dev)) |
| mei_me_check_fw_reset(dev); |
| if (ret) |
| return ret; |
| dev_dbg(dev->dev, "hw is ready\n"); |
| |
| mei_me_host_set_ready(dev); |
| return ret; |
| } |
| |
| |
| /** |
| * mei_hbuf_filled_slots - gets number of device filled buffer slots |
| * |
| * @dev: the device structure |
| * |
| * Return: number of filled slots |
| */ |
| static unsigned char mei_hbuf_filled_slots(struct mei_device *dev) |
| { |
| u32 hcsr; |
| char read_ptr, write_ptr; |
| |
| hcsr = mei_hcsr_read(dev); |
| |
| read_ptr = (char) ((hcsr & H_CBRP) >> 8); |
| write_ptr = (char) ((hcsr & H_CBWP) >> 16); |
| |
| return (unsigned char) (write_ptr - read_ptr); |
| } |
| |
| /** |
| * mei_me_hbuf_is_empty - checks if host buffer is empty. |
| * |
| * @dev: the device structure |
| * |
| * Return: true if empty, false - otherwise. |
| */ |
| static bool mei_me_hbuf_is_empty(struct mei_device *dev) |
| { |
| return mei_hbuf_filled_slots(dev) == 0; |
| } |
| |
| /** |
| * mei_me_hbuf_empty_slots - counts write empty slots. |
| * |
| * @dev: the device structure |
| * |
| * Return: -EOVERFLOW if overflow, otherwise empty slots count |
| */ |
| static int mei_me_hbuf_empty_slots(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| unsigned char filled_slots, empty_slots; |
| |
| filled_slots = mei_hbuf_filled_slots(dev); |
| empty_slots = hw->hbuf_depth - filled_slots; |
| |
| /* check for overflow */ |
| if (filled_slots > hw->hbuf_depth) |
| return -EOVERFLOW; |
| |
| return empty_slots; |
| } |
| |
| /** |
| * mei_me_hbuf_depth - returns depth of the hw buffer. |
| * |
| * @dev: the device structure |
| * |
| * Return: size of hw buffer in slots |
| */ |
| static u32 mei_me_hbuf_depth(const struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| return hw->hbuf_depth; |
| } |
| |
| /** |
| * mei_me_hbuf_write - writes a message to host hw buffer. |
| * |
| * @dev: the device structure |
| * @hdr: header of message |
| * @hdr_len: header length in bytes: must be multiplication of a slot (4bytes) |
| * @data: payload |
| * @data_len: payload length in bytes |
| * |
| * Return: 0 if success, < 0 - otherwise. |
| */ |
| static int mei_me_hbuf_write(struct mei_device *dev, |
| const void *hdr, size_t hdr_len, |
| const void *data, size_t data_len) |
| { |
| unsigned long rem; |
| unsigned long i; |
| const u32 *reg_buf; |
| u32 dw_cnt; |
| int empty_slots; |
| |
| if (WARN_ON(!hdr || hdr_len & 0x3)) |
| return -EINVAL; |
| |
| if (!data && data_len) { |
| dev_err(dev->dev, "wrong parameters null data with data_len = %zu\n", data_len); |
| return -EINVAL; |
| } |
| |
| dev_dbg(dev->dev, MEI_HDR_FMT, MEI_HDR_PRM((struct mei_msg_hdr *)hdr)); |
| |
| empty_slots = mei_hbuf_empty_slots(dev); |
| dev_dbg(dev->dev, "empty slots = %d.\n", empty_slots); |
| |
| if (empty_slots < 0) |
| return -EOVERFLOW; |
| |
| dw_cnt = mei_data2slots(hdr_len + data_len); |
| if (dw_cnt > (u32)empty_slots) |
| return -EMSGSIZE; |
| |
| reg_buf = hdr; |
| for (i = 0; i < hdr_len / MEI_SLOT_SIZE; i++) |
| mei_me_hcbww_write(dev, reg_buf[i]); |
| |
| reg_buf = data; |
| for (i = 0; i < data_len / MEI_SLOT_SIZE; i++) |
| mei_me_hcbww_write(dev, reg_buf[i]); |
| |
| rem = data_len & 0x3; |
| if (rem > 0) { |
| u32 reg = 0; |
| |
| memcpy(®, (const u8 *)data + data_len - rem, rem); |
| mei_me_hcbww_write(dev, reg); |
| } |
| |
| mei_hcsr_set_hig(dev); |
| if (!mei_me_hw_is_ready(dev)) |
| return -EIO; |
| |
| return 0; |
| } |
| |
| /** |
| * mei_me_count_full_read_slots - counts read full slots. |
| * |
| * @dev: the device structure |
| * |
| * Return: -EOVERFLOW if overflow, otherwise filled slots count |
| */ |
| static int mei_me_count_full_read_slots(struct mei_device *dev) |
| { |
| u32 me_csr; |
| char read_ptr, write_ptr; |
| unsigned char buffer_depth, filled_slots; |
| |
| me_csr = mei_me_mecsr_read(dev); |
| buffer_depth = (unsigned char)((me_csr & ME_CBD_HRA) >> 24); |
| read_ptr = (char) ((me_csr & ME_CBRP_HRA) >> 8); |
| write_ptr = (char) ((me_csr & ME_CBWP_HRA) >> 16); |
| filled_slots = (unsigned char) (write_ptr - read_ptr); |
| |
| /* check for overflow */ |
| if (filled_slots > buffer_depth) |
| return -EOVERFLOW; |
| |
| dev_dbg(dev->dev, "filled_slots =%08x\n", filled_slots); |
| return (int)filled_slots; |
| } |
| |
| /** |
| * mei_me_read_slots - reads a message from mei device. |
| * |
| * @dev: the device structure |
| * @buffer: message buffer will be written |
| * @buffer_length: message size will be read |
| * |
| * Return: always 0 |
| */ |
| static int mei_me_read_slots(struct mei_device *dev, unsigned char *buffer, |
| unsigned long buffer_length) |
| { |
| u32 *reg_buf = (u32 *)buffer; |
| |
| for (; buffer_length >= MEI_SLOT_SIZE; buffer_length -= MEI_SLOT_SIZE) |
| *reg_buf++ = mei_me_mecbrw_read(dev); |
| |
| if (buffer_length > 0) { |
| u32 reg = mei_me_mecbrw_read(dev); |
| |
| memcpy(reg_buf, ®, buffer_length); |
| } |
| |
| mei_hcsr_set_hig(dev); |
| return 0; |
| } |
| |
| /** |
| * mei_me_pg_set - write pg enter register |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_pg_set(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 reg; |
| |
| reg = mei_me_reg_read(hw, H_HPG_CSR); |
| trace_mei_reg_read(dev->dev, "H_HPG_CSR", H_HPG_CSR, reg); |
| |
| reg |= H_HPG_CSR_PGI; |
| |
| trace_mei_reg_write(dev->dev, "H_HPG_CSR", H_HPG_CSR, reg); |
| mei_me_reg_write(hw, H_HPG_CSR, reg); |
| } |
| |
| /** |
| * mei_me_pg_unset - write pg exit register |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_pg_unset(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 reg; |
| |
| reg = mei_me_reg_read(hw, H_HPG_CSR); |
| trace_mei_reg_read(dev->dev, "H_HPG_CSR", H_HPG_CSR, reg); |
| |
| WARN(!(reg & H_HPG_CSR_PGI), "PGI is not set\n"); |
| |
| reg |= H_HPG_CSR_PGIHEXR; |
| |
| trace_mei_reg_write(dev->dev, "H_HPG_CSR", H_HPG_CSR, reg); |
| mei_me_reg_write(hw, H_HPG_CSR, reg); |
| } |
| |
| /** |
| * mei_me_pg_legacy_enter_sync - perform legacy pg entry procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_pg_legacy_enter_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| int ret; |
| |
| dev->pg_event = MEI_PG_EVENT_WAIT; |
| |
| ret = mei_hbm_pg(dev, MEI_PG_ISOLATION_ENTRY_REQ_CMD); |
| if (ret) |
| return ret; |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_RECEIVED, |
| dev->timeouts.pgi); |
| mutex_lock(&dev->device_lock); |
| |
| if (dev->pg_event == MEI_PG_EVENT_RECEIVED) { |
| mei_me_pg_set(dev); |
| ret = 0; |
| } else { |
| ret = -ETIME; |
| } |
| |
| dev->pg_event = MEI_PG_EVENT_IDLE; |
| hw->pg_state = MEI_PG_ON; |
| |
| return ret; |
| } |
| |
| /** |
| * mei_me_pg_legacy_exit_sync - perform legacy pg exit procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_pg_legacy_exit_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| int ret; |
| |
| if (dev->pg_event == MEI_PG_EVENT_RECEIVED) |
| goto reply; |
| |
| dev->pg_event = MEI_PG_EVENT_WAIT; |
| |
| mei_me_pg_unset(dev); |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_RECEIVED, |
| dev->timeouts.pgi); |
| mutex_lock(&dev->device_lock); |
| |
| reply: |
| if (dev->pg_event != MEI_PG_EVENT_RECEIVED) { |
| ret = -ETIME; |
| goto out; |
| } |
| |
| dev->pg_event = MEI_PG_EVENT_INTR_WAIT; |
| ret = mei_hbm_pg(dev, MEI_PG_ISOLATION_EXIT_RES_CMD); |
| if (ret) |
| return ret; |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_INTR_RECEIVED, |
| dev->timeouts.pgi); |
| mutex_lock(&dev->device_lock); |
| |
| if (dev->pg_event == MEI_PG_EVENT_INTR_RECEIVED) |
| ret = 0; |
| else |
| ret = -ETIME; |
| |
| out: |
| dev->pg_event = MEI_PG_EVENT_IDLE; |
| hw->pg_state = MEI_PG_OFF; |
| |
| return ret; |
| } |
| |
| /** |
| * mei_me_pg_in_transition - is device now in pg transition |
| * |
| * @dev: the device structure |
| * |
| * Return: true if in pg transition, false otherwise |
| */ |
| static bool mei_me_pg_in_transition(struct mei_device *dev) |
| { |
| return dev->pg_event >= MEI_PG_EVENT_WAIT && |
| dev->pg_event <= MEI_PG_EVENT_INTR_WAIT; |
| } |
| |
| /** |
| * mei_me_pg_is_enabled - detect if PG is supported by HW |
| * |
| * @dev: the device structure |
| * |
| * Return: true is pg supported, false otherwise |
| */ |
| static bool mei_me_pg_is_enabled(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 reg = mei_me_mecsr_read(dev); |
| |
| if (hw->d0i3_supported) |
| return true; |
| |
| if ((reg & ME_PGIC_HRA) == 0) |
| goto notsupported; |
| |
| if (!dev->hbm_f_pg_supported) |
| goto notsupported; |
| |
| return true; |
| |
| notsupported: |
| dev_dbg(dev->dev, "pg: not supported: d0i3 = %d HGP = %d hbm version %d.%d ?= %d.%d\n", |
| hw->d0i3_supported, |
| !!(reg & ME_PGIC_HRA), |
| dev->version.major_version, |
| dev->version.minor_version, |
| HBM_MAJOR_VERSION_PGI, |
| HBM_MINOR_VERSION_PGI); |
| |
| return false; |
| } |
| |
| /** |
| * mei_me_d0i3_set - write d0i3 register bit on mei device. |
| * |
| * @dev: the device structure |
| * @intr: ask for interrupt |
| * |
| * Return: D0I3C register value |
| */ |
| static u32 mei_me_d0i3_set(struct mei_device *dev, bool intr) |
| { |
| u32 reg = mei_me_d0i3c_read(dev); |
| |
| reg |= H_D0I3C_I3; |
| if (intr) |
| reg |= H_D0I3C_IR; |
| else |
| reg &= ~H_D0I3C_IR; |
| mei_me_d0i3c_write(dev, reg); |
| /* read it to ensure HW consistency */ |
| reg = mei_me_d0i3c_read(dev); |
| return reg; |
| } |
| |
| /** |
| * mei_me_d0i3_unset - clean d0i3 register bit on mei device. |
| * |
| * @dev: the device structure |
| * |
| * Return: D0I3C register value |
| */ |
| static u32 mei_me_d0i3_unset(struct mei_device *dev) |
| { |
| u32 reg = mei_me_d0i3c_read(dev); |
| |
| reg &= ~H_D0I3C_I3; |
| reg |= H_D0I3C_IR; |
| mei_me_d0i3c_write(dev, reg); |
| /* read it to ensure HW consistency */ |
| reg = mei_me_d0i3c_read(dev); |
| return reg; |
| } |
| |
| /** |
| * mei_me_d0i3_enter_sync - perform d0i3 entry procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_d0i3_enter_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| int ret; |
| u32 reg; |
| |
| reg = mei_me_d0i3c_read(dev); |
| if (reg & H_D0I3C_I3) { |
| /* we are in d0i3, nothing to do */ |
| dev_dbg(dev->dev, "d0i3 set not needed\n"); |
| ret = 0; |
| goto on; |
| } |
| |
| /* PGI entry procedure */ |
| dev->pg_event = MEI_PG_EVENT_WAIT; |
| |
| ret = mei_hbm_pg(dev, MEI_PG_ISOLATION_ENTRY_REQ_CMD); |
| if (ret) |
| /* FIXME: should we reset here? */ |
| goto out; |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_RECEIVED, |
| dev->timeouts.pgi); |
| mutex_lock(&dev->device_lock); |
| |
| if (dev->pg_event != MEI_PG_EVENT_RECEIVED) { |
| ret = -ETIME; |
| goto out; |
| } |
| /* end PGI entry procedure */ |
| |
| dev->pg_event = MEI_PG_EVENT_INTR_WAIT; |
| |
| reg = mei_me_d0i3_set(dev, true); |
| if (!(reg & H_D0I3C_CIP)) { |
| dev_dbg(dev->dev, "d0i3 enter wait not needed\n"); |
| ret = 0; |
| goto on; |
| } |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_INTR_RECEIVED, |
| dev->timeouts.d0i3); |
| mutex_lock(&dev->device_lock); |
| |
| if (dev->pg_event != MEI_PG_EVENT_INTR_RECEIVED) { |
| reg = mei_me_d0i3c_read(dev); |
| if (!(reg & H_D0I3C_I3)) { |
| ret = -ETIME; |
| goto out; |
| } |
| } |
| |
| ret = 0; |
| on: |
| hw->pg_state = MEI_PG_ON; |
| out: |
| dev->pg_event = MEI_PG_EVENT_IDLE; |
| dev_dbg(dev->dev, "d0i3 enter ret = %d\n", ret); |
| return ret; |
| } |
| |
| /** |
| * mei_me_d0i3_enter - perform d0i3 entry procedure |
| * no hbm PG handshake |
| * no waiting for confirmation; runs with interrupts |
| * disabled |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_d0i3_enter(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 reg; |
| |
| reg = mei_me_d0i3c_read(dev); |
| if (reg & H_D0I3C_I3) { |
| /* we are in d0i3, nothing to do */ |
| dev_dbg(dev->dev, "already d0i3 : set not needed\n"); |
| goto on; |
| } |
| |
| mei_me_d0i3_set(dev, false); |
| on: |
| hw->pg_state = MEI_PG_ON; |
| dev->pg_event = MEI_PG_EVENT_IDLE; |
| dev_dbg(dev->dev, "d0i3 enter\n"); |
| return 0; |
| } |
| |
| /** |
| * mei_me_d0i3_exit_sync - perform d0i3 exit procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_d0i3_exit_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| int ret; |
| u32 reg; |
| |
| dev->pg_event = MEI_PG_EVENT_INTR_WAIT; |
| |
| reg = mei_me_d0i3c_read(dev); |
| if (!(reg & H_D0I3C_I3)) { |
| /* we are not in d0i3, nothing to do */ |
| dev_dbg(dev->dev, "d0i3 exit not needed\n"); |
| ret = 0; |
| goto off; |
| } |
| |
| reg = mei_me_d0i3_unset(dev); |
| if (!(reg & H_D0I3C_CIP)) { |
| dev_dbg(dev->dev, "d0i3 exit wait not needed\n"); |
| ret = 0; |
| goto off; |
| } |
| |
| mutex_unlock(&dev->device_lock); |
| wait_event_timeout(dev->wait_pg, |
| dev->pg_event == MEI_PG_EVENT_INTR_RECEIVED, |
| dev->timeouts.d0i3); |
| mutex_lock(&dev->device_lock); |
| |
| if (dev->pg_event != MEI_PG_EVENT_INTR_RECEIVED) { |
| reg = mei_me_d0i3c_read(dev); |
| if (reg & H_D0I3C_I3) { |
| ret = -ETIME; |
| goto out; |
| } |
| } |
| |
| ret = 0; |
| off: |
| hw->pg_state = MEI_PG_OFF; |
| out: |
| dev->pg_event = MEI_PG_EVENT_IDLE; |
| |
| dev_dbg(dev->dev, "d0i3 exit ret = %d\n", ret); |
| return ret; |
| } |
| |
| /** |
| * mei_me_pg_legacy_intr - perform legacy pg processing |
| * in interrupt thread handler |
| * |
| * @dev: the device structure |
| */ |
| static void mei_me_pg_legacy_intr(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (dev->pg_event != MEI_PG_EVENT_INTR_WAIT) |
| return; |
| |
| dev->pg_event = MEI_PG_EVENT_INTR_RECEIVED; |
| hw->pg_state = MEI_PG_OFF; |
| if (waitqueue_active(&dev->wait_pg)) |
| wake_up(&dev->wait_pg); |
| } |
| |
| /** |
| * mei_me_d0i3_intr - perform d0i3 processing in interrupt thread handler |
| * |
| * @dev: the device structure |
| * @intr_source: interrupt source |
| */ |
| static void mei_me_d0i3_intr(struct mei_device *dev, u32 intr_source) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (dev->pg_event == MEI_PG_EVENT_INTR_WAIT && |
| (intr_source & H_D0I3C_IS)) { |
| dev->pg_event = MEI_PG_EVENT_INTR_RECEIVED; |
| if (hw->pg_state == MEI_PG_ON) { |
| hw->pg_state = MEI_PG_OFF; |
| if (dev->hbm_state != MEI_HBM_IDLE) { |
| /* |
| * force H_RDY because it could be |
| * wiped off during PG |
| */ |
| dev_dbg(dev->dev, "d0i3 set host ready\n"); |
| mei_me_host_set_ready(dev); |
| } |
| } else { |
| hw->pg_state = MEI_PG_ON; |
| } |
| |
| wake_up(&dev->wait_pg); |
| } |
| |
| if (hw->pg_state == MEI_PG_ON && (intr_source & H_IS)) { |
| /* |
| * HW sent some data and we are in D0i3, so |
| * we got here because of HW initiated exit from D0i3. |
| * Start runtime pm resume sequence to exit low power state. |
| */ |
| dev_dbg(dev->dev, "d0i3 want resume\n"); |
| mei_hbm_pg_resume(dev); |
| } |
| } |
| |
| /** |
| * mei_me_pg_intr - perform pg processing in interrupt thread handler |
| * |
| * @dev: the device structure |
| * @intr_source: interrupt source |
| */ |
| static void mei_me_pg_intr(struct mei_device *dev, u32 intr_source) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (hw->d0i3_supported) |
| mei_me_d0i3_intr(dev, intr_source); |
| else |
| mei_me_pg_legacy_intr(dev); |
| } |
| |
| /** |
| * mei_me_pg_enter_sync - perform runtime pm entry procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| int mei_me_pg_enter_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (hw->d0i3_supported) |
| return mei_me_d0i3_enter_sync(dev); |
| else |
| return mei_me_pg_legacy_enter_sync(dev); |
| } |
| |
| /** |
| * mei_me_pg_exit_sync - perform runtime pm exit procedure |
| * |
| * @dev: the device structure |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| int mei_me_pg_exit_sync(struct mei_device *dev) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| |
| if (hw->d0i3_supported) |
| return mei_me_d0i3_exit_sync(dev); |
| else |
| return mei_me_pg_legacy_exit_sync(dev); |
| } |
| |
| /** |
| * mei_me_hw_reset - resets fw via mei csr register. |
| * |
| * @dev: the device structure |
| * @intr_enable: if interrupt should be enabled after reset. |
| * |
| * Return: 0 on success an error code otherwise |
| */ |
| static int mei_me_hw_reset(struct mei_device *dev, bool intr_enable) |
| { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| int ret; |
| u32 hcsr; |
| |
| if (intr_enable) { |
| mei_me_intr_enable(dev); |
| if (hw->d0i3_supported) { |
| ret = mei_me_d0i3_exit_sync(dev); |
| if (ret) |
| return ret; |
| } else { |
| hw->pg_state = MEI_PG_OFF; |
| } |
| } |
| |
| pm_runtime_set_active(dev->dev); |
| |
| hcsr = mei_hcsr_read(dev); |
| /* H_RST may be found lit before reset is started, |
| * for example if preceding reset flow hasn't completed. |
| * In that case asserting H_RST will be ignored, therefore |
| * we need to clean H_RST bit to start a successful reset sequence. |
| */ |
| if ((hcsr & H_RST) == H_RST) { |
| dev_warn(dev->dev, "H_RST is set = 0x%08X", hcsr); |
| hcsr &= ~H_RST; |
| mei_hcsr_set(dev, hcsr); |
| hcsr = mei_hcsr_read(dev); |
| } |
| |
| hcsr |= H_RST | H_IG | H_CSR_IS_MASK; |
| |
| if (!intr_enable || mei_me_hw_use_polling(to_me_hw(dev))) |
| hcsr &= ~H_CSR_IE_MASK; |
| |
| dev->recvd_hw_ready = false; |
| mei_hcsr_write(dev, hcsr); |
| |
| /* |
| * Host reads the H_CSR once to ensure that the |
| * posted write to H_CSR completes. |
| */ |
| hcsr = mei_hcsr_read(dev); |
| |
| if ((hcsr & H_RST) == 0) |
| dev_warn(dev->dev, "H_RST is not set = 0x%08X", hcsr); |
| |
| if ((hcsr & H_RDY) == H_RDY) |
| dev_warn(dev->dev, "H_RDY is not cleared 0x%08X", hcsr); |
| |
| if (!intr_enable) { |
| mei_me_hw_reset_release(dev); |
| if (hw->d0i3_supported) { |
| ret = mei_me_d0i3_enter(dev); |
| if (ret) |
| return ret; |
| } |
| } |
| return 0; |
| } |
| |
| /** |
| * mei_me_irq_quick_handler - The ISR of the MEI device |
| * |
| * @irq: The irq number |
| * @dev_id: pointer to the device structure |
| * |
| * Return: irqreturn_t |
| */ |
| irqreturn_t mei_me_irq_quick_handler(int irq, void *dev_id) |
| { |
| struct mei_device *dev = (struct mei_device *)dev_id; |
| u32 hcsr; |
| |
| hcsr = mei_hcsr_read(dev); |
| if (!me_intr_src(hcsr)) |
| return IRQ_NONE; |
| |
| dev_dbg(dev->dev, "interrupt source 0x%08X\n", me_intr_src(hcsr)); |
| |
| /* disable interrupts on device */ |
| me_intr_disable(dev, hcsr); |
| return IRQ_WAKE_THREAD; |
| } |
| EXPORT_SYMBOL_GPL(mei_me_irq_quick_handler); |
| |
| /** |
| * mei_me_irq_thread_handler - function called after ISR to handle the interrupt |
| * processing. |
| * |
| * @irq: The irq number |
| * @dev_id: pointer to the device structure |
| * |
| * Return: irqreturn_t |
| * |
| */ |
| irqreturn_t mei_me_irq_thread_handler(int irq, void *dev_id) |
| { |
| struct mei_device *dev = (struct mei_device *) dev_id; |
| struct list_head cmpl_list; |
| s32 slots; |
| u32 hcsr; |
| int rets = 0; |
| |
| dev_dbg(dev->dev, "function called after ISR to handle the interrupt processing.\n"); |
| /* initialize our complete list */ |
| mutex_lock(&dev->device_lock); |
| |
| hcsr = mei_hcsr_read(dev); |
| me_intr_clear(dev, hcsr); |
| |
| INIT_LIST_HEAD(&cmpl_list); |
| |
| /* check if ME wants a reset */ |
| if (!mei_hw_is_ready(dev) && dev->dev_state != MEI_DEV_RESETTING) { |
| if (kind_is_gsc(dev) || kind_is_gscfi(dev)) { |
| dev_dbg(dev->dev, "FW not ready: resetting: dev_state = %d\n", |
| dev->dev_state); |
| } else { |
| dev_warn(dev->dev, "FW not ready: resetting: dev_state = %d\n", |
| dev->dev_state); |
| } |
| if (dev->dev_state == MEI_DEV_POWERING_DOWN || |
| dev->dev_state == MEI_DEV_POWER_DOWN) |
| mei_cl_all_disconnect(dev); |
| else if (dev->dev_state != MEI_DEV_DISABLED) |
| schedule_work(&dev->reset_work); |
| goto end; |
| } |
| |
| if (mei_me_hw_is_resetting(dev)) |
| mei_hcsr_set_hig(dev); |
| |
| mei_me_pg_intr(dev, me_intr_src(hcsr)); |
| |
| /* check if we need to start the dev */ |
| if (!mei_host_is_ready(dev)) { |
| if (mei_hw_is_ready(dev)) { |
| dev_dbg(dev->dev, "we need to start the dev.\n"); |
| dev->recvd_hw_ready = true; |
| wake_up(&dev->wait_hw_ready); |
| } else { |
| dev_dbg(dev->dev, "Spurious Interrupt\n"); |
| } |
| goto end; |
| } |
| /* check slots available for reading */ |
| slots = mei_count_full_read_slots(dev); |
| while (slots > 0) { |
| dev_dbg(dev->dev, "slots to read = %08x\n", slots); |
| rets = mei_irq_read_handler(dev, &cmpl_list, &slots); |
| /* There is a race between ME write and interrupt delivery: |
| * Not all data is always available immediately after the |
| * interrupt, so try to read again on the next interrupt. |
| */ |
| if (rets == -ENODATA) |
| break; |
| |
| if (rets) { |
| dev_err(dev->dev, "mei_irq_read_handler ret = %d, state = %d.\n", |
| rets, dev->dev_state); |
| if (dev->dev_state != MEI_DEV_RESETTING && |
| dev->dev_state != MEI_DEV_DISABLED && |
| dev->dev_state != MEI_DEV_POWERING_DOWN && |
| dev->dev_state != MEI_DEV_POWER_DOWN) |
| schedule_work(&dev->reset_work); |
| goto end; |
| } |
| } |
| |
| dev->hbuf_is_ready = mei_hbuf_is_ready(dev); |
| |
| /* |
| * During PG handshake only allowed write is the replay to the |
| * PG exit message, so block calling write function |
| * if the pg event is in PG handshake |
| */ |
| if (dev->pg_event != MEI_PG_EVENT_WAIT && |
| dev->pg_event != MEI_PG_EVENT_RECEIVED) { |
| rets = mei_irq_write_handler(dev, &cmpl_list); |
| dev->hbuf_is_ready = mei_hbuf_is_ready(dev); |
| } |
| |
| mei_irq_compl_handler(dev, &cmpl_list); |
| |
| end: |
| dev_dbg(dev->dev, "interrupt thread end ret = %d\n", rets); |
| mei_me_intr_enable(dev); |
| mutex_unlock(&dev->device_lock); |
| return IRQ_HANDLED; |
| } |
| EXPORT_SYMBOL_GPL(mei_me_irq_thread_handler); |
| |
| #define MEI_POLLING_TIMEOUT_ACTIVE 100 |
| #define MEI_POLLING_TIMEOUT_IDLE 500 |
| |
| /** |
| * mei_me_polling_thread - interrupt register polling thread |
| * |
| * @_dev: mei device |
| * |
| * The thread monitors the interrupt source register and calls |
| * mei_me_irq_thread_handler() to handle the firmware |
| * input. |
| * |
| * The function polls in MEI_POLLING_TIMEOUT_ACTIVE timeout |
| * in case there was an event, in idle case the polling |
| * time increases yet again by MEI_POLLING_TIMEOUT_ACTIVE |
| * up to MEI_POLLING_TIMEOUT_IDLE. |
| * |
| * Return: always 0 |
| */ |
| int mei_me_polling_thread(void *_dev) |
| { |
| struct mei_device *dev = _dev; |
| irqreturn_t irq_ret; |
| long polling_timeout = MEI_POLLING_TIMEOUT_ACTIVE; |
| |
| dev_dbg(dev->dev, "kernel thread is running\n"); |
| while (!kthread_should_stop()) { |
| struct mei_me_hw *hw = to_me_hw(dev); |
| u32 hcsr; |
| |
| wait_event_timeout(hw->wait_active, |
| hw->is_active || kthread_should_stop(), |
| msecs_to_jiffies(MEI_POLLING_TIMEOUT_IDLE)); |
| |
| if (kthread_should_stop()) |
| break; |
| |
| hcsr = mei_hcsr_read(dev); |
| if (me_intr_src(hcsr)) { |
| polling_timeout = MEI_POLLING_TIMEOUT_ACTIVE; |
| irq_ret = mei_me_irq_thread_handler(1, dev); |
| if (irq_ret != IRQ_HANDLED) |
| dev_err(dev->dev, "irq_ret %d\n", irq_ret); |
| } else { |
| /* |
| * Increase timeout by MEI_POLLING_TIMEOUT_ACTIVE |
| * up to MEI_POLLING_TIMEOUT_IDLE |
| */ |
| polling_timeout = clamp_val(polling_timeout + MEI_POLLING_TIMEOUT_ACTIVE, |
| MEI_POLLING_TIMEOUT_ACTIVE, |
| MEI_POLLING_TIMEOUT_IDLE); |
| } |
| |
| schedule_timeout_interruptible(msecs_to_jiffies(polling_timeout)); |
| } |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(mei_me_polling_thread); |
| |
| static const struct mei_hw_ops mei_me_hw_ops = { |
| |
| .trc_status = mei_me_trc_status, |
| .fw_status = mei_me_fw_status, |
| .pg_state = mei_me_pg_state, |
| |
| .host_is_ready = mei_me_host_is_ready, |
| |
| .hw_is_ready = mei_me_hw_is_ready, |
| .hw_reset = mei_me_hw_reset, |
| .hw_config = mei_me_hw_config, |
| .hw_start = mei_me_hw_start, |
| |
| .pg_in_transition = mei_me_pg_in_transition, |
| .pg_is_enabled = mei_me_pg_is_enabled, |
| |
| .intr_clear = mei_me_intr_clear, |
| .intr_enable = mei_me_intr_enable, |
| .intr_disable = mei_me_intr_disable, |
| .synchronize_irq = mei_me_synchronize_irq, |
| |
| .hbuf_free_slots = mei_me_hbuf_empty_slots, |
| .hbuf_is_ready = mei_me_hbuf_is_empty, |
| .hbuf_depth = mei_me_hbuf_depth, |
| |
| .write = mei_me_hbuf_write, |
| |
| .rdbuf_full_slots = mei_me_count_full_read_slots, |
| .read_hdr = mei_me_mecbrw_read, |
| .read = mei_me_read_slots |
| }; |
| |
| /** |
| * mei_me_fw_type_nm() - check for nm sku |
| * |
| * @pdev: pci device |
| * |
| * Read ME FW Status register to check for the Node Manager (NM) Firmware. |
| * The NM FW is only signaled in PCI function 0. |
| * __Note__: Deprecated by PCH8 and newer. |
| * |
| * Return: true in case of NM firmware |
| */ |
| static bool mei_me_fw_type_nm(const struct pci_dev *pdev) |
| { |
| u32 reg; |
| unsigned int devfn; |
| |
| devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0); |
| pci_bus_read_config_dword(pdev->bus, devfn, PCI_CFG_HFS_2, ®); |
| trace_mei_pci_cfg_read(&pdev->dev, "PCI_CFG_HFS_2", PCI_CFG_HFS_2, reg); |
| /* make sure that bit 9 (NM) is up and bit 10 (DM) is down */ |
| return (reg & 0x600) == 0x200; |
| } |
| |
| #define MEI_CFG_FW_NM \ |
| .quirk_probe = mei_me_fw_type_nm |
| |
| /** |
| * mei_me_fw_type_sps_4() - check for sps 4.0 sku |
| * |
| * @pdev: pci device |
| * |
| * Read ME FW Status register to check for SPS Firmware. |
| * The SPS FW is only signaled in the PCI function 0. |
| * __Note__: Deprecated by SPS 5.0 and newer. |
| * |
| * Return: true in case of SPS firmware |
| */ |
| static bool mei_me_fw_type_sps_4(const struct pci_dev *pdev) |
| { |
| u32 reg; |
| unsigned int devfn; |
| |
| devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0); |
| pci_bus_read_config_dword(pdev->bus, devfn, PCI_CFG_HFS_1, ®); |
| trace_mei_pci_cfg_read(&pdev->dev, "PCI_CFG_HFS_1", PCI_CFG_HFS_1, reg); |
| return (reg & PCI_CFG_HFS_1_OPMODE_MSK) == PCI_CFG_HFS_1_OPMODE_SPS; |
| } |
| |
| #define MEI_CFG_FW_SPS_4 \ |
| .quirk_probe = mei_me_fw_type_sps_4 |
| |
| /** |
| * mei_me_fw_type_sps_ign() - check for sps or ign sku |
| * |
| * @pdev: pci device |
| * |
| * Read ME FW Status register to check for SPS or IGN Firmware. |
| * The SPS/IGN FW is only signaled in pci function 0 |
| * |
| * Return: true in case of SPS/IGN firmware |
| */ |
| static bool mei_me_fw_type_sps_ign(const struct pci_dev *pdev) |
| { |
| u32 reg; |
| u32 fw_type; |
| unsigned int devfn; |
| |
| devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0); |
| pci_bus_read_config_dword(pdev->bus, devfn, PCI_CFG_HFS_3, ®); |
| trace_mei_pci_cfg_read(&pdev->dev, "PCI_CFG_HFS_3", PCI_CFG_HFS_3, reg); |
| fw_type = (reg & PCI_CFG_HFS_3_FW_SKU_MSK); |
| |
| dev_dbg(&pdev->dev, "fw type is %d\n", fw_type); |
| |
| return fw_type == PCI_CFG_HFS_3_FW_SKU_IGN || |
| fw_type == PCI_CFG_HFS_3_FW_SKU_SPS; |
| } |
| |
| #define MEI_CFG_KIND_ITOUCH \ |
| .kind = "itouch" |
| |
| #define MEI_CFG_TYPE_GSC \ |
| .kind = "gsc" |
| |
| #define MEI_CFG_TYPE_GSCFI \ |
| .kind = "gscfi" |
| |
| #define MEI_CFG_FW_SPS_IGN \ |
| .quirk_probe = mei_me_fw_type_sps_ign |
| |
| #define MEI_CFG_FW_VER_SUPP \ |
| .fw_ver_supported = 1 |
| |
| #define MEI_CFG_ICH_HFS \ |
| .fw_status.count = 0 |
| |
| #define MEI_CFG_ICH10_HFS \ |
| .fw_status.count = 1, \ |
| .fw_status.status[0] = PCI_CFG_HFS_1 |
| |
| #define MEI_CFG_PCH_HFS \ |
| .fw_status.count = 2, \ |
| .fw_status.status[0] = PCI_CFG_HFS_1, \ |
| .fw_status.status[1] = PCI_CFG_HFS_2 |
| |
| #define MEI_CFG_PCH8_HFS \ |
| .fw_status.count = 6, \ |
| .fw_status.status[0] = PCI_CFG_HFS_1, \ |
| .fw_status.status[1] = PCI_CFG_HFS_2, \ |
| .fw_status.status[2] = PCI_CFG_HFS_3, \ |
| .fw_status.status[3] = PCI_CFG_HFS_4, \ |
| .fw_status.status[4] = PCI_CFG_HFS_5, \ |
| .fw_status.status[5] = PCI_CFG_HFS_6 |
| |
| #define MEI_CFG_DMA_128 \ |
| .dma_size[DMA_DSCR_HOST] = SZ_128K, \ |
| .dma_size[DMA_DSCR_DEVICE] = SZ_128K, \ |
| .dma_size[DMA_DSCR_CTRL] = PAGE_SIZE |
| |
| #define MEI_CFG_TRC \ |
| .hw_trc_supported = 1 |
| |
| /* ICH Legacy devices */ |
| static const struct mei_cfg mei_me_ich_cfg = { |
| MEI_CFG_ICH_HFS, |
| }; |
| |
| /* ICH devices */ |
| static const struct mei_cfg mei_me_ich10_cfg = { |
| MEI_CFG_ICH10_HFS, |
| }; |
| |
| /* PCH6 devices */ |
| static const struct mei_cfg mei_me_pch6_cfg = { |
| MEI_CFG_PCH_HFS, |
| }; |
| |
| /* PCH7 devices */ |
| static const struct mei_cfg mei_me_pch7_cfg = { |
| MEI_CFG_PCH_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| }; |
| |
| /* PCH Cougar Point and Patsburg with quirk for Node Manager exclusion */ |
| static const struct mei_cfg mei_me_pch_cpt_pbg_cfg = { |
| MEI_CFG_PCH_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_FW_NM, |
| }; |
| |
| /* PCH8 Lynx Point and newer devices */ |
| static const struct mei_cfg mei_me_pch8_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| }; |
| |
| /* PCH8 Lynx Point and newer devices - iTouch */ |
| static const struct mei_cfg mei_me_pch8_itouch_cfg = { |
| MEI_CFG_KIND_ITOUCH, |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| }; |
| |
| /* PCH8 Lynx Point with quirk for SPS Firmware exclusion */ |
| static const struct mei_cfg mei_me_pch8_sps_4_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_FW_SPS_4, |
| }; |
| |
| /* LBG with quirk for SPS (4.0) Firmware exclusion */ |
| static const struct mei_cfg mei_me_pch12_sps_4_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_FW_SPS_4, |
| }; |
| |
| /* Cannon Lake and newer devices */ |
| static const struct mei_cfg mei_me_pch12_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_DMA_128, |
| }; |
| |
| /* Cannon Lake with quirk for SPS 5.0 and newer Firmware exclusion */ |
| static const struct mei_cfg mei_me_pch12_sps_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_DMA_128, |
| MEI_CFG_FW_SPS_IGN, |
| }; |
| |
| /* Cannon Lake itouch with quirk for SPS 5.0 and newer Firmware exclusion |
| * w/o DMA support. |
| */ |
| static const struct mei_cfg mei_me_pch12_itouch_sps_cfg = { |
| MEI_CFG_KIND_ITOUCH, |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_FW_SPS_IGN, |
| }; |
| |
| /* Tiger Lake and newer devices */ |
| static const struct mei_cfg mei_me_pch15_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_DMA_128, |
| MEI_CFG_TRC, |
| }; |
| |
| /* Tiger Lake with quirk for SPS 5.0 and newer Firmware exclusion */ |
| static const struct mei_cfg mei_me_pch15_sps_cfg = { |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| MEI_CFG_DMA_128, |
| MEI_CFG_TRC, |
| MEI_CFG_FW_SPS_IGN, |
| }; |
| |
| /* Graphics System Controller */ |
| static const struct mei_cfg mei_me_gsc_cfg = { |
| MEI_CFG_TYPE_GSC, |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| }; |
| |
| /* Graphics System Controller Firmware Interface */ |
| static const struct mei_cfg mei_me_gscfi_cfg = { |
| MEI_CFG_TYPE_GSCFI, |
| MEI_CFG_PCH8_HFS, |
| MEI_CFG_FW_VER_SUPP, |
| }; |
| |
| /* |
| * mei_cfg_list - A list of platform platform specific configurations. |
| * Note: has to be synchronized with enum mei_cfg_idx. |
| */ |
| static const struct mei_cfg *const mei_cfg_list[] = { |
| [MEI_ME_UNDEF_CFG] = NULL, |
| [MEI_ME_ICH_CFG] = &mei_me_ich_cfg, |
| [MEI_ME_ICH10_CFG] = &mei_me_ich10_cfg, |
| [MEI_ME_PCH6_CFG] = &mei_me_pch6_cfg, |
| [MEI_ME_PCH7_CFG] = &mei_me_pch7_cfg, |
| [MEI_ME_PCH_CPT_PBG_CFG] = &mei_me_pch_cpt_pbg_cfg, |
| [MEI_ME_PCH8_CFG] = &mei_me_pch8_cfg, |
| [MEI_ME_PCH8_ITOUCH_CFG] = &mei_me_pch8_itouch_cfg, |
| [MEI_ME_PCH8_SPS_4_CFG] = &mei_me_pch8_sps_4_cfg, |
| [MEI_ME_PCH12_CFG] = &mei_me_pch12_cfg, |
| [MEI_ME_PCH12_SPS_4_CFG] = &mei_me_pch12_sps_4_cfg, |
| [MEI_ME_PCH12_SPS_CFG] = &mei_me_pch12_sps_cfg, |
| [MEI_ME_PCH12_SPS_ITOUCH_CFG] = &mei_me_pch12_itouch_sps_cfg, |
| [MEI_ME_PCH15_CFG] = &mei_me_pch15_cfg, |
| [MEI_ME_PCH15_SPS_CFG] = &mei_me_pch15_sps_cfg, |
| [MEI_ME_GSC_CFG] = &mei_me_gsc_cfg, |
| [MEI_ME_GSCFI_CFG] = &mei_me_gscfi_cfg, |
| }; |
| |
| const struct mei_cfg *mei_me_get_cfg(kernel_ulong_t idx) |
| { |
| BUILD_BUG_ON(ARRAY_SIZE(mei_cfg_list) != MEI_ME_NUM_CFG); |
| |
| if (idx >= MEI_ME_NUM_CFG) |
| return NULL; |
| |
| return mei_cfg_list[idx]; |
| } |
| EXPORT_SYMBOL_GPL(mei_me_get_cfg); |
| |
| /** |
| * mei_me_dev_init - allocates and initializes the mei device structure |
| * |
| * @parent: device associated with physical device (pci/platform) |
| * @cfg: per device generation config |
| * @slow_fw: configure longer timeouts as FW is slow |
| * |
| * Return: The mei_device pointer on success, NULL on failure. |
| */ |
| struct mei_device *mei_me_dev_init(struct device *parent, |
| const struct mei_cfg *cfg, bool slow_fw) |
| { |
| struct mei_device *dev; |
| struct mei_me_hw *hw; |
| int i; |
| |
| dev = devm_kzalloc(parent, sizeof(*dev) + sizeof(*hw), GFP_KERNEL); |
| if (!dev) |
| return NULL; |
| |
| hw = to_me_hw(dev); |
| |
| for (i = 0; i < DMA_DSCR_NUM; i++) |
| dev->dr_dscr[i].size = cfg->dma_size[i]; |
| |
| mei_device_init(dev, parent, slow_fw, &mei_me_hw_ops); |
| hw->cfg = cfg; |
| |
| dev->fw_f_fw_ver_supported = cfg->fw_ver_supported; |
| |
| dev->kind = cfg->kind; |
| |
| return dev; |
| } |
| EXPORT_SYMBOL_GPL(mei_me_dev_init); |