blob: ae515651fc6bb96857a764bcab06c3b546271ebb [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only
%YAML 1.2
---
$id: http://devicetree.org/schemas/connector/usb-connector.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: USB Connector
maintainers:
- Rob Herring <robh@kernel.org>
description:
A USB connector node represents a physical USB connector. It should be a child
of a USB interface controller or a separate node when it is attached to both
MUX and USB interface controller.
properties:
compatible:
oneOf:
- enum:
- usb-a-connector
- usb-b-connector
- usb-c-connector
- items:
- const: gpio-usb-b-connector
- const: usb-b-connector
- items:
- const: samsung,usb-connector-11pin
- const: usb-b-connector
label:
description: Symbolic name for the connector.
type:
description: Size of the connector, should be specified in case of
non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible
connectors.
$ref: /schemas/types.yaml#/definitions/string
enum:
- mini
- micro
self-powered:
description: Set this property if the USB device has its own power source.
type: boolean
# The following are optional properties for "usb-b-connector".
id-gpios:
description: An input gpio for USB ID pin.
maxItems: 1
vbus-gpios:
description: An input gpio for USB VBus pin, used to detect presence of
VBUS 5V.
maxItems: 1
vbus-supply:
description: A phandle to the regulator for USB VBUS if needed when host
mode or dual role mode is supported.
Particularly, if use an output GPIO to control a VBUS regulator, should
model it as a regulator. See bindings/regulator/fixed-regulator.yaml
# The following are optional properties for "usb-c-connector".
power-role:
description: Determines the power role that the Type C connector will
support. "dual" refers to Dual Role Port (DRP).
$ref: /schemas/types.yaml#/definitions/string
enum:
- source
- sink
- dual
try-power-role:
description: Preferred power role.
$ref: /schemas/types.yaml#/definitions/string
enum:
- source
- sink
- dual
data-role:
description: Data role if Type C connector supports USB data. "dual" refers
Dual Role Device (DRD).
$ref: /schemas/types.yaml#/definitions/string
enum:
- host
- device
- dual
typec-power-opmode:
description: Determines the power operation mode that the Type C connector
will support and will advertise through CC pins when it has no power
delivery support.
- "default" corresponds to default USB voltage and current defined by the
USB 2.0 and USB 3.2 specifications, 5V 500mA for USB 2.0 ports and
5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane
operation respectively.
- "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB
Type-C Cable and Connector specification, when Power Delivery is not
supported.
$ref: /schemas/types.yaml#/definitions/string
enum:
- default
- 1.5A
- 3.0A
pd-disable:
description: Set this property if the Type-C connector has no power delivery support.
type: boolean
# The following are optional properties for "usb-c-connector" with power
# delivery support.
source-pdos:
description: An array of u32 with each entry providing supported power
source data object(PDO), the detailed bit definitions of PDO can be found
in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2
Source_Capabilities Message, the order of each entry(PDO) should follow
the PD spec chapter 6.4.1. Required for power source and power dual role.
User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO()
defined in dt-bindings/usb/pd.h.
minItems: 1
maxItems: 7
$ref: /schemas/types.yaml#/definitions/uint32-array
sink-pdos:
description: An array of u32 with each entry providing supported power sink
data object(PDO), the detailed bit definitions of PDO can be found in
"Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3
Sink Capabilities Message, the order of each entry(PDO) should follow the
PD spec chapter 6.4.1. Required for power sink and power dual role. User
can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined
in dt-bindings/usb/pd.h.
minItems: 1
maxItems: 7
$ref: /schemas/types.yaml#/definitions/uint32-array
sink-vdos:
description: An array of u32 with each entry, a Vendor Defined Message Object (VDO),
providing additional information corresponding to the product, the detailed bit
definitions and the order of each VDO can be found in
"USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10"
chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via
VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in
dt-bindings/usb/pd.h.
minItems: 3
maxItems: 6
$ref: /schemas/types.yaml#/definitions/uint32-array
sink-vdos-v1:
description: An array of u32 with each entry, a Vendor Defined Message Object (VDO),
providing additional information corresponding to the product, the detailed bit
definitions and the order of each VDO can be found in
"USB Power Delivery Specification Revision 2.0, Version 1.3" chapter 6.4.4.3.1 Discover
Identity. User can specify the VDO array via VDO_IDH/_CERT/_PRODUCT/_CABLE/_AMA defined in
dt-bindings/usb/pd.h.
minItems: 3
maxItems: 6
$ref: /schemas/types.yaml#/definitions/uint32-array
op-sink-microwatt:
description: Sink required operating power in microwatt, if source can't
offer the power, Capability Mismatch is set. Required for power sink and
power dual role.
ports:
$ref: /schemas/graph.yaml#/properties/ports
description: OF graph bindings modeling any data bus to the connector
unless the bus is between parent node and the connector. Since a single
connector can have multiple data buses every bus has an assigned OF graph
port number as described below.
properties:
port@0:
$ref: /schemas/graph.yaml#/properties/port
description: High Speed (HS), present in all connectors.
port@1:
$ref: /schemas/graph.yaml#/properties/port
description: Super Speed (SS), present in SS capable connectors.
port@2:
$ref: /schemas/graph.yaml#/properties/port
description: Sideband Use (SBU), present in USB-C. This describes the
alternate mode connection of which SBU is a part.
required:
- port@0
new-source-frs-typec-current:
description: Initial current capability of the new source when vSafe5V
is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink"
of "USB Power Delivery Specification Revision 3.0, Version 1.2" provides the
different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current"
provides a detailed description of the field. The sink PDO from current source
reflects the current source's(i.e. transmitter of the FRS signal) power
requirement during fr swap. The current sink (i.e. receiver of the FRS signal),
a.k.a new source, should check if it will be able to satisfy the current source's,
new sink's, requirement during frswap before enabling the frs signal reception.
This property refers to maximum current capability that the current sink can
satisfy. During FRS, VBUS voltage is at 5V, as the partners are in implicit
contract, hence, the power level is only a function of the current capability.
"1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink".
"2" refers to 1.5A@5V.
"3" refers to 3.0A@5V.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [1, 2, 3]
slow-charger-loop:
description: Allows PMIC charger loops which are slow(i.e. cannot meet the 15ms deadline) to
still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby
state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification
Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W -
5V@500mA) upon entering SNK_DISCOVERY(instead of 3A or the 1.5A, Rp current advertised, during
SNK_DISCOVERY) and the actual currrent limit after reception of PS_Ready for PD link or during
SNK_READY for non-pd link.
type: boolean
dependencies:
sink-vdos-v1: [ 'sink-vdos' ]
sink-vdos: [ 'sink-vdos-v1' ]
required:
- compatible
allOf:
- if:
properties:
compatible:
contains:
const: gpio-usb-b-connector
then:
anyOf:
- required:
- vbus-gpios
- required:
- id-gpios
- if:
properties:
compatible:
contains:
const: samsung,usb-connector-11pin
then:
properties:
type:
const: micro
anyOf:
- not:
required:
- typec-power-opmode
- new-source-frs-typec-current
additionalProperties: true
examples:
# Micro-USB connector with HS lines routed via controller (MUIC).
- |
muic-max77843 {
usb_con1: connector {
compatible = "usb-b-connector";
label = "micro-USB";
type = "micro";
};
};
# USB-C connector attached to CC controller (s2mm005), HS lines routed
# to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort.
# DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
- |
ccic: s2mm005 {
usb_con2: connector {
compatible = "usb-c-connector";
label = "USB-C";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
usb_con_hs: endpoint {
remote-endpoint = <&max77865_usbc_hs>;
};
};
port@1 {
reg = <1>;
usb_con_ss: endpoint {
remote-endpoint = <&usbdrd_phy_ss>;
};
};
port@2 {
reg = <2>;
usb_con_sbu: endpoint {
remote-endpoint = <&dp_aux>;
};
};
};
};
};
# USB-C connector attached to a typec port controller(ptn5110), which has
# power delivery support and enables drp.
- |
#include <dt-bindings/usb/pd.h>
typec: ptn5110 {
usb_con3: connector {
compatible = "usb-c-connector";
label = "USB-C";
power-role = "dual";
try-power-role = "sink";
source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
PDO_VAR(5000, 12000, 2000)>;
op-sink-microwatt = <10000000>;
};
};
# USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220)
# with SS 2:1 MUX. HS lines routed to SoC, SS lines routed to the MUX and
# the output of MUX is connected to the SoC.
- |
connector {
compatible = "usb-c-connector";
label = "USB-C";
data-role = "dual";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
hs_ep: endpoint {
remote-endpoint = <&usb3_hs_ep>;
};
};
port@1 {
reg = <1>;
ss_ep: endpoint {
remote-endpoint = <&hd3ss3220_in_ep>;
};
};
};
};
# USB connector with GPIO control lines
- |
#include <dt-bindings/gpio/gpio.h>
usb {
connector {
compatible = "gpio-usb-b-connector", "usb-b-connector";
type = "micro";
id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
vbus-supply = <&usb_p0_vbus>;
};
};
# Micro-USB connector with HS lines routed via controller (MUIC) and MHL
# lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based
# mobile phone
- |
muic-max77843 {
usb_con4: connector {
compatible = "samsung,usb-connector-11pin", "usb-b-connector";
label = "micro-USB";
type = "micro";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
muic_to_usb: endpoint {
remote-endpoint = <&usb_to_muic>;
};
};
port@3 {
reg = <3>;
usb_con_mhl: endpoint {
remote-endpoint = <&sii8620_mhl>;
};
};
};
};
};