| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2019, Linaro Limited |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/power/qcom-aoss-qmp.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/clock/qcom,gcc-sm8150.h> |
| #include <dt-bindings/clock/qcom,gpucc-sm8150.h> |
| #include <dt-bindings/interconnect/qcom,osm-l3.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <38400000>; |
| clock-output-names = "xo_board"; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32764>; |
| clock-output-names = "sleep_clk"; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x0>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_0: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| L3_0: l3-cache { |
| compatible = "cache"; |
| }; |
| }; |
| }; |
| |
| CPU1: cpu@100 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_100>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_100: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| |
| }; |
| |
| CPU2: cpu@200 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x200>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_200>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_200: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU3: cpu@300 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x300>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_300>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_300: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU4: cpu@400 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x400>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_400>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_400: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU5: cpu@500 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x500>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_500>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_500: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU6: cpu@600 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x600>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_600>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_600: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU7: cpu@700 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x700>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_700>; |
| qcom,freq-domain = <&cpufreq_hw 2>; |
| #cooling-cells = <2>; |
| L2_700: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm-sm8150", "qcom,scm"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| tcsr_mutex: hwlock { |
| compatible = "qcom,tcsr-mutex"; |
| syscon = <&tcsr_mutex_regs 0 0x1000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0x0 0x80000000 0x0 0x0>; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| hyp_mem: memory@85700000 { |
| reg = <0x0 0x85700000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| xbl_mem: memory@85d00000 { |
| reg = <0x0 0x85d00000 0x0 0x140000>; |
| no-map; |
| }; |
| |
| aop_mem: memory@85f00000 { |
| reg = <0x0 0x85f00000 0x0 0x20000>; |
| no-map; |
| }; |
| |
| aop_cmd_db: memory@85f20000 { |
| compatible = "qcom,cmd-db"; |
| reg = <0x0 0x85f20000 0x0 0x20000>; |
| no-map; |
| }; |
| |
| smem_mem: memory@86000000 { |
| reg = <0x0 0x86000000 0x0 0x200000>; |
| no-map; |
| }; |
| |
| tz_mem: memory@86200000 { |
| reg = <0x0 0x86200000 0x0 0x3900000>; |
| no-map; |
| }; |
| |
| rmtfs_mem: memory@89b00000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0x0 0x89b00000 0x0 0x200000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <15>; |
| }; |
| |
| camera_mem: memory@8b700000 { |
| reg = <0x0 0x8b700000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| wlan_mem: memory@8bc00000 { |
| reg = <0x0 0x8bc00000 0x0 0x180000>; |
| no-map; |
| }; |
| |
| npu_mem: memory@8bd80000 { |
| reg = <0x0 0x8bd80000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@8be00000 { |
| reg = <0x0 0x8be00000 0x0 0x1a00000>; |
| no-map; |
| }; |
| |
| mpss_mem: memory@8d800000 { |
| reg = <0x0 0x8d800000 0x0 0x9600000>; |
| no-map; |
| }; |
| |
| venus_mem: memory@96e00000 { |
| reg = <0x0 0x96e00000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| slpi_mem: memory@97300000 { |
| reg = <0x0 0x97300000 0x0 0x1400000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: memory@98700000 { |
| reg = <0x0 0x98700000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| ipa_gsi_mem: memory@98710000 { |
| reg = <0x0 0x98710000 0x0 0x5000>; |
| no-map; |
| }; |
| |
| gpu_mem: memory@98715000 { |
| reg = <0x0 0x98715000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| spss_mem: memory@98800000 { |
| reg = <0x0 0x98800000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| cdsp_mem: memory@98900000 { |
| reg = <0x0 0x98900000 0x0 0x1400000>; |
| no-map; |
| }; |
| |
| qseecom_mem: memory@9e400000 { |
| reg = <0x0 0x9e400000 0x0 0x1400000>; |
| no-map; |
| }; |
| }; |
| |
| smem { |
| compatible = "qcom,smem"; |
| memory-region = <&smem_mem>; |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| smp2p-cdsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <94>, <432>; |
| |
| interrupts = <GIC_SPI 576 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 6>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <5>; |
| |
| cdsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| cdsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-lpass { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| |
| interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 10>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| adsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| adsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-mpss { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| |
| interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 14>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| modem_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-slpi { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <481>, <430>; |
| |
| interrupts = <GIC_SPI 172 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apss_shared 26>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <3>; |
| |
| slpi_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| slpi_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0 0 0 0 0x10 0>; |
| dma-ranges = <0 0 0 0 0x10 0>; |
| compatible = "simple-bus"; |
| |
| gcc: clock-controller@100000 { |
| compatible = "qcom,gcc-sm8150"; |
| reg = <0x0 0x00100000 0x0 0x1f0000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clock-names = "bi_tcxo", |
| "sleep_clk"; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&sleep_clk>; |
| }; |
| |
| qupv3_id_1: geniqup@ac0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0x0 0x00ac0000 0x0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| status = "disabled"; |
| |
| uart2: serial@a90000 { |
| compatible = "qcom,geni-debug-uart"; |
| reg = <0x0 0x00a90000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| config_noc: interconnect@1500000 { |
| compatible = "qcom,sm8150-config-noc"; |
| reg = <0 0x01500000 0 0x7400>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| system_noc: interconnect@1620000 { |
| compatible = "qcom,sm8150-system-noc"; |
| reg = <0 0x01620000 0 0x19400>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mc_virt: interconnect@163a000 { |
| compatible = "qcom,sm8150-mc-virt"; |
| reg = <0 0x0163a000 0 0x1000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre1_noc: interconnect@16e0000 { |
| compatible = "qcom,sm8150-aggre1-noc"; |
| reg = <0 0x016e0000 0 0xd080>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre2_noc: interconnect@1700000 { |
| compatible = "qcom,sm8150-aggre2-noc"; |
| reg = <0 0x01700000 0 0x20000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| compute_noc: interconnect@1720000 { |
| compatible = "qcom,sm8150-compute-noc"; |
| reg = <0 0x01720000 0 0x7000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mmss_noc: interconnect@1740000 { |
| compatible = "qcom,sm8150-mmss-noc"; |
| reg = <0 0x01740000 0 0x1c100>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| ufs_mem_hc: ufshc@1d84000 { |
| compatible = "qcom,sm8150-ufshc", "qcom,ufshc", |
| "jedec,ufs-2.0"; |
| reg = <0 0x01d84000 0 0x2500>; |
| interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&ufs_mem_phy_lanes>; |
| phy-names = "ufsphy"; |
| lanes-per-direction = <2>; |
| #reset-cells = <1>; |
| resets = <&gcc GCC_UFS_PHY_BCR>; |
| reset-names = "rst"; |
| |
| clock-names = |
| "core_clk", |
| "bus_aggr_clk", |
| "iface_clk", |
| "core_clk_unipro", |
| "ref_clk", |
| "tx_lane0_sync_clk", |
| "rx_lane0_sync_clk", |
| "rx_lane1_sync_clk"; |
| clocks = |
| <&gcc GCC_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_UFS_PHY_AHB_CLK>, |
| <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; |
| freq-table-hz = |
| <37500000 300000000>, |
| <0 0>, |
| <0 0>, |
| <37500000 300000000>, |
| <0 0>, |
| <0 0>, |
| <0 0>, |
| <0 0>; |
| |
| status = "disabled"; |
| }; |
| |
| ufs_mem_phy: phy@1d87000 { |
| compatible = "qcom,sm8150-qmp-ufs-phy"; |
| reg = <0 0x01d87000 0 0x1c0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| clock-names = "ref", |
| "ref_aux"; |
| clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>, |
| <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; |
| |
| resets = <&ufs_mem_hc 0>; |
| reset-names = "ufsphy"; |
| status = "disabled"; |
| |
| ufs_mem_phy_lanes: lanes@1d87400 { |
| reg = <0 0x01d87400 0 0x108>, |
| <0 0x01d87600 0 0x1e0>, |
| <0 0x01d87c00 0 0x1dc>, |
| <0 0x01d87800 0 0x108>, |
| <0 0x01d87a00 0 0x1e0>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| ipa_virt: interconnect@1e00000 { |
| compatible = "qcom,sm8150-ipa-virt"; |
| reg = <0 0x01e00000 0 0x1000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| tcsr_mutex_regs: syscon@1f40000 { |
| compatible = "syscon"; |
| reg = <0x0 0x01f40000 0x0 0x40000>; |
| }; |
| |
| remoteproc_slpi: remoteproc@2400000 { |
| compatible = "qcom,sm8150-slpi-pas"; |
| reg = <0x0 0x02400000 0x0 0x4040>; |
| |
| interrupts-extended = <&intc GIC_SPI 494 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>, |
| <&rpmhpd 3>, |
| <&rpmhpd 2>; |
| power-domain-names = "load_state", "lcx", "lmx"; |
| |
| memory-region = <&slpi_mem>; |
| |
| qcom,smem-states = <&slpi_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 170 IRQ_TYPE_EDGE_RISING>; |
| label = "dsps"; |
| qcom,remote-pid = <3>; |
| mboxes = <&apss_shared 24>; |
| }; |
| }; |
| |
| gpu: gpu@2c00000 { |
| /* |
| * note: the amd,imageon compatible makes it possible |
| * to use the drm/msm driver without the display node, |
| * make sure to remove it when display node is added |
| */ |
| compatible = "qcom,adreno-640.1", |
| "qcom,adreno", |
| "amd,imageon"; |
| #stream-id-cells = <16>; |
| |
| reg = <0 0x02c00000 0 0x40000>; |
| reg-names = "kgsl_3d0_reg_memory"; |
| |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&adreno_smmu 0 0x401>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| qcom,gmu = <&gmu>; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| }; |
| |
| /* note: downstream checks gpu binning for 675 Mhz */ |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-675000000 { |
| opp-hz = /bits/ 64 <675000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| opp-585000000 { |
| opp-hz = /bits/ 64 <585000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| opp-499200000 { |
| opp-hz = /bits/ 64 <499200000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>; |
| }; |
| |
| opp-427000000 { |
| opp-hz = /bits/ 64 <427000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| opp-345000000 { |
| opp-hz = /bits/ 64 <345000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| opp-257000000 { |
| opp-hz = /bits/ 64 <257000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| }; |
| }; |
| |
| gmu: gmu@2c6a000 { |
| compatible="qcom,adreno-gmu-640.1", "qcom,adreno-gmu"; |
| |
| reg = <0 0x02c6a000 0 0x30000>, |
| <0 0x0b290000 0 0x10000>, |
| <0 0x0b490000 0 0x10000>; |
| reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq"; |
| |
| interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hfi", "gmu"; |
| |
| clocks = <&gpucc GPU_CC_AHB_CLK>, |
| <&gpucc GPU_CC_CX_GMU_CLK>, |
| <&gpucc GPU_CC_CXO_CLK>, |
| <&gcc GCC_DDRSS_GPU_AXI_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>; |
| clock-names = "ahb", "gmu", "cxo", "axi", "memnoc"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>, |
| <&gpucc GPU_GX_GDSC>; |
| power-domain-names = "cx", "gx"; |
| |
| iommus = <&adreno_smmu 5 0x400>; |
| |
| operating-points-v2 = <&gmu_opp_table>; |
| |
| gmu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| }; |
| }; |
| |
| gpucc: clock-controller@2c90000 { |
| compatible = "qcom,sm8150-gpucc"; |
| reg = <0 0x02c90000 0 0x9000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_GPU_GPLL0_CLK_SRC>, |
| <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>; |
| clock-names = "bi_tcxo", |
| "gcc_gpu_gpll0_clk_src", |
| "gcc_gpu_gpll0_div_clk_src"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| adreno_smmu: iommu@2ca0000 { |
| compatible = "qcom,sm8150-smmu-500", "arm,mmu-500"; |
| reg = <0 0x02ca0000 0 0x10000>; |
| #iommu-cells = <2>; |
| #global-interrupts = <1>; |
| interrupts = <GIC_SPI 674 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gpucc GPU_CC_AHB_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>, |
| <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>; |
| clock-names = "ahb", "bus", "iface"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>; |
| }; |
| |
| tlmm: pinctrl@3100000 { |
| compatible = "qcom,sm8150-pinctrl"; |
| reg = <0x0 0x03100000 0x0 0x300000>, |
| <0x0 0x03500000 0x0 0x300000>, |
| <0x0 0x03900000 0x0 0x300000>, |
| <0x0 0x03D00000 0x0 0x300000>; |
| reg-names = "west", "east", "north", "south"; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-ranges = <&tlmm 0 0 175>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| remoteproc_mpss: remoteproc@4080000 { |
| compatible = "qcom,sm8150-mpss-pas"; |
| reg = <0x0 0x04080000 0x0 0x4040>; |
| |
| interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", "handover", |
| "stop-ack", "shutdown-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>, |
| <&rpmhpd 7>, |
| <&rpmhpd 0>; |
| power-domain-names = "load_state", "cx", "mss"; |
| |
| memory-region = <&mpss_mem>; |
| |
| qcom,smem-states = <&modem_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>; |
| label = "modem"; |
| qcom,remote-pid = <1>; |
| mboxes = <&apss_shared 12>; |
| }; |
| }; |
| |
| remoteproc_cdsp: remoteproc@8300000 { |
| compatible = "qcom,sm8150-cdsp-pas"; |
| reg = <0x0 0x08300000 0x0 0x4040>; |
| |
| interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>, |
| <&rpmhpd 7>; |
| power-domain-names = "load_state", "cx"; |
| |
| memory-region = <&cdsp_mem>; |
| |
| qcom,smem-states = <&cdsp_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 574 IRQ_TYPE_EDGE_RISING>; |
| label = "cdsp"; |
| qcom,remote-pid = <5>; |
| mboxes = <&apss_shared 4>; |
| }; |
| }; |
| |
| usb_1_hsphy: phy@88e2000 { |
| compatible = "qcom,sm8150-usb-hs-phy", |
| "qcom,usb-snps-hs-7nm-phy"; |
| reg = <0 0x088e2000 0 0x400>; |
| status = "disabled"; |
| #phy-cells = <0>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; |
| }; |
| |
| usb_1_qmpphy: phy@88e9000 { |
| compatible = "qcom,sm8150-qmp-usb3-phy"; |
| reg = <0 0x088e9000 0 0x18c>, |
| <0 0x088e8000 0 0x10>; |
| reg-names = "reg-base", "dp_com"; |
| status = "disabled"; |
| #clock-cells = <1>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_PRIM_CLKREF_CLK>, |
| <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; |
| clock-names = "aux", "ref_clk_src", "ref", "com_aux"; |
| |
| resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, |
| <&gcc GCC_USB3_PHY_PRIM_BCR>; |
| reset-names = "phy", "common"; |
| |
| usb_1_ssphy: lanes@88e9200 { |
| reg = <0 0x088e9200 0 0x200>, |
| <0 0x088e9400 0 0x200>, |
| <0 0x088e9c00 0 0x218>, |
| <0 0x088e9600 0 0x200>, |
| <0 0x088e9800 0 0x200>, |
| <0 0x088e9a00 0 0x100>; |
| #phy-cells = <0>; |
| clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; |
| clock-names = "pipe0"; |
| clock-output-names = "usb3_phy_pipe_clk_src"; |
| }; |
| }; |
| |
| dc_noc: interconnect@9160000 { |
| compatible = "qcom,sm8150-dc-noc"; |
| reg = <0 0x09160000 0 0x3200>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| gem_noc: interconnect@9680000 { |
| compatible = "qcom,sm8150-gem-noc"; |
| reg = <0 0x09680000 0 0x3e200>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| usb_1: usb@a6f8800 { |
| compatible = "qcom,sm8150-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a6f8800 0 0x400>; |
| status = "disabled"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| dma-ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_PRIM_SLEEP_CLK>, |
| <&gcc GCC_USB3_SEC_CLKREF_CLK>; |
| clock-names = "cfg_noc", "core", "iface", "mock_utmi", |
| "sleep", "xo"; |
| |
| assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <200000000>; |
| |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hs_phy_irq", "ss_phy_irq", |
| "dm_hs_phy_irq", "dp_hs_phy_irq"; |
| |
| power-domains = <&gcc USB30_PRIM_GDSC>; |
| |
| resets = <&gcc GCC_USB30_PRIM_BCR>; |
| |
| usb_1_dwc3: dwc3@a600000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a600000 0 0xcd00>; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| phys = <&usb_1_hsphy>, <&usb_1_ssphy>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| }; |
| }; |
| |
| camnoc_virt: interconnect@ac00000 { |
| compatible = "qcom,sm8150-camnoc-virt"; |
| reg = <0 0x0ac00000 0 0x1000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aoss_qmp: power-controller@c300000 { |
| compatible = "qcom,sm8150-aoss-qmp"; |
| reg = <0x0 0x0c300000 0x0 0x100000>; |
| interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apss_shared 0>; |
| |
| #clock-cells = <0>; |
| #power-domain-cells = <1>; |
| }; |
| |
| tsens0: thermal-sensor@c263000 { |
| compatible = "qcom,sm8150-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c263000 0 0x1ff>, /* TM */ |
| <0 0x0c222000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <16>; |
| interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens1: thermal-sensor@c265000 { |
| compatible = "qcom,sm8150-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c265000 0 0x1ff>, /* TM */ |
| <0 0x0c223000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <8>; |
| interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| spmi_bus: spmi@c440000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0 0x0c440000 0x0 0x0001100>, |
| <0x0 0x0c600000 0x0 0x2000000>, |
| <0x0 0x0e600000 0x0 0x0100000>, |
| <0x0 0x0e700000 0x0 0x00a0000>, |
| <0x0 0x0c40a000 0x0 0x0026000>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| cell-index = <0>; |
| }; |
| |
| remoteproc_adsp: remoteproc@17300000 { |
| compatible = "qcom,sm8150-adsp-pas"; |
| reg = <0x0 0x17300000 0x0 0x4040>; |
| |
| interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>, |
| <&rpmhpd 7>; |
| power-domain-names = "load_state", "cx"; |
| |
| memory-region = <&adsp_mem>; |
| |
| qcom,smem-states = <&adsp_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>; |
| label = "lpass"; |
| qcom,remote-pid = <2>; |
| mboxes = <&apss_shared 8>; |
| }; |
| }; |
| |
| intc: interrupt-controller@17a00000 { |
| compatible = "arm,gic-v3"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ |
| <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| apss_shared: mailbox@17c00000 { |
| compatible = "qcom,sm8150-apss-shared"; |
| reg = <0x0 0x17c00000 0x0 0x1000>; |
| #mbox-cells = <1>; |
| }; |
| |
| watchdog@17c10000 { |
| compatible = "qcom,apss-wdt-sm8150", "qcom,kpss-wdt"; |
| reg = <0 0x17c10000 0 0x1000>; |
| clocks = <&sleep_clk>; |
| }; |
| |
| timer@17c20000 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0 0x17c20000 0x0 0x1000>; |
| clock-frequency = <19200000>; |
| |
| frame@17c21000{ |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c21000 0x0 0x1000>, |
| <0x0 0x17c22000 0x0 0x1000>; |
| }; |
| |
| frame@17c23000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c23000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c25000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c25000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c27000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c26000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c29000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c29000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c2b000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c2b000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c2d000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c2d000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| apps_rsc: rsc@18200000 { |
| label = "apps_rsc"; |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0x0 0x18200000 0x0 0x10000>, |
| <0x0 0x18210000 0x0 0x10000>, |
| <0x0 0x18220000 0x0 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 2>, |
| <SLEEP_TCS 1>, |
| <WAKE_TCS 1>, |
| <CONTROL_TCS 0>; |
| |
| rpmhcc: clock-controller { |
| compatible = "qcom,sm8150-rpmh-clk"; |
| #clock-cells = <1>; |
| clock-names = "xo"; |
| clocks = <&xo_board>; |
| }; |
| |
| rpmhpd: power-controller { |
| compatible = "qcom,sm8150-rpmhpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmhpd_opp_table>; |
| |
| rpmhpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmhpd_opp_ret: opp1 { |
| opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; |
| }; |
| |
| rpmhpd_opp_min_svs: opp2 { |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs: opp3 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmhpd_opp_svs: opp4 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| rpmhpd_opp_svs_l1: opp5 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_svs_l2: opp6 { |
| opp-level = <224>; |
| }; |
| |
| rpmhpd_opp_nom: opp7 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| rpmhpd_opp_nom_l1: opp8 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| rpmhpd_opp_nom_l2: opp9 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; |
| }; |
| |
| rpmhpd_opp_turbo: opp10 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| }; |
| |
| rpmhpd_opp_turbo_l1: opp11 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| }; |
| }; |
| }; |
| |
| apps_bcm_voter: bcm_voter { |
| compatible = "qcom,bcm-voter"; |
| }; |
| }; |
| |
| osm_l3: interconnect@18321000 { |
| compatible = "qcom,sm8150-osm-l3"; |
| reg = <0 0x18321000 0 0x1400>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #interconnect-cells = <1>; |
| }; |
| |
| cpufreq_hw: cpufreq@18323000 { |
| compatible = "qcom,cpufreq-hw"; |
| reg = <0 0x18323000 0 0x1400>, <0 0x18325800 0 0x1400>, |
| <0 0x18327800 0 0x1400>; |
| reg-names = "freq-domain0", "freq-domain1", |
| "freq-domain2"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #freq-domain-cells = <1>; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| thermal-zones { |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 1>; |
| |
| trips { |
| cpu0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu0_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu0_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 2>; |
| |
| trips { |
| cpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu1_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu1_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 3>; |
| |
| trips { |
| cpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu2_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu2_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 4>; |
| |
| trips { |
| cpu3_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu3_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu3_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu4-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 7>; |
| |
| trips { |
| cpu4_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu4_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu4_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu5-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 8>; |
| |
| trips { |
| cpu5_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu5_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu5_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu6-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 9>; |
| |
| trips { |
| cpu6_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu6_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu6_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu7-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 10>; |
| |
| trips { |
| cpu7_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu7_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu7_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu4-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 11>; |
| |
| trips { |
| cpu4_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu4_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu4_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu5-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 12>; |
| |
| trips { |
| cpu5_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu5_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu5_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu6-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 13>; |
| |
| trips { |
| cpu6_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu6_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu6_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu7-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 14>; |
| |
| trips { |
| cpu7_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu7_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu7_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| aoss0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 0>; |
| |
| trips { |
| aoss0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cluster0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 5>; |
| |
| trips { |
| cluster0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster0_crit: cluster0_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cluster1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 6>; |
| |
| trips { |
| cluster1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster1_crit: cluster1_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal-top { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 15>; |
| |
| trips { |
| gpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| aoss1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 0>; |
| |
| trips { |
| aoss1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| wlan-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 1>; |
| |
| trips { |
| wlan_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| video-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 2>; |
| |
| trips { |
| video_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| mem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 3>; |
| |
| trips { |
| mem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| q6-hvx-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 4>; |
| |
| trips { |
| q6_hvx_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| camera-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 5>; |
| |
| trips { |
| camera_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| compute-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 6>; |
| |
| trips { |
| compute_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| modem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 7>; |
| |
| trips { |
| modem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| npu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 8>; |
| |
| trips { |
| npu_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| modem-vec-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 9>; |
| |
| trips { |
| modem_vec_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| modem-scl-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 10>; |
| |
| trips { |
| modem_scl_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal-bottom { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 11>; |
| |
| trips { |
| gpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| }; |
| }; |
