| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * A devfreq driver for NVIDIA Tegra SoCs |
| * |
| * Copyright (c) 2014 NVIDIA CORPORATION. All rights reserved. |
| * Copyright (C) 2014 Google, Inc |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/cpufreq.h> |
| #include <linux/devfreq.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/irq.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_opp.h> |
| #include <linux/reset.h> |
| #include <linux/workqueue.h> |
| |
| #include <soc/tegra/fuse.h> |
| |
| #include "governor.h" |
| |
| #define ACTMON_GLB_STATUS 0x0 |
| #define ACTMON_GLB_PERIOD_CTRL 0x4 |
| |
| #define ACTMON_DEV_CTRL 0x0 |
| #define ACTMON_DEV_CTRL_K_VAL_SHIFT 10 |
| #define ACTMON_DEV_CTRL_ENB_PERIODIC BIT(18) |
| #define ACTMON_DEV_CTRL_AVG_BELOW_WMARK_EN BIT(20) |
| #define ACTMON_DEV_CTRL_AVG_ABOVE_WMARK_EN BIT(21) |
| #define ACTMON_DEV_CTRL_CONSECUTIVE_BELOW_WMARK_NUM_SHIFT 23 |
| #define ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_NUM_SHIFT 26 |
| #define ACTMON_DEV_CTRL_CONSECUTIVE_BELOW_WMARK_EN BIT(29) |
| #define ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_EN BIT(30) |
| #define ACTMON_DEV_CTRL_ENB BIT(31) |
| |
| #define ACTMON_DEV_CTRL_STOP 0x00000000 |
| |
| #define ACTMON_DEV_UPPER_WMARK 0x4 |
| #define ACTMON_DEV_LOWER_WMARK 0x8 |
| #define ACTMON_DEV_INIT_AVG 0xc |
| #define ACTMON_DEV_AVG_UPPER_WMARK 0x10 |
| #define ACTMON_DEV_AVG_LOWER_WMARK 0x14 |
| #define ACTMON_DEV_COUNT_WEIGHT 0x18 |
| #define ACTMON_DEV_AVG_COUNT 0x20 |
| #define ACTMON_DEV_INTR_STATUS 0x24 |
| |
| #define ACTMON_INTR_STATUS_CLEAR 0xffffffff |
| |
| #define ACTMON_DEV_INTR_CONSECUTIVE_UPPER BIT(31) |
| #define ACTMON_DEV_INTR_CONSECUTIVE_LOWER BIT(30) |
| |
| #define ACTMON_ABOVE_WMARK_WINDOW 1 |
| #define ACTMON_BELOW_WMARK_WINDOW 3 |
| #define ACTMON_BOOST_FREQ_STEP 16000 |
| |
| /* |
| * ACTMON_AVERAGE_WINDOW_LOG2: default value for @DEV_CTRL_K_VAL, which |
| * translates to 2 ^ (K_VAL + 1). ex: 2 ^ (6 + 1) = 128 |
| */ |
| #define ACTMON_AVERAGE_WINDOW_LOG2 6 |
| #define ACTMON_SAMPLING_PERIOD 12 /* ms */ |
| #define ACTMON_DEFAULT_AVG_BAND 6 /* 1/10 of % */ |
| |
| #define KHZ 1000 |
| |
| #define KHZ_MAX (ULONG_MAX / KHZ) |
| |
| /* Assume that the bus is saturated if the utilization is 25% */ |
| #define BUS_SATURATION_RATIO 25 |
| |
| /** |
| * struct tegra_devfreq_device_config - configuration specific to an ACTMON |
| * device |
| * |
| * Coefficients and thresholds are percentages unless otherwise noted |
| */ |
| struct tegra_devfreq_device_config { |
| u32 offset; |
| u32 irq_mask; |
| |
| /* Factors applied to boost_freq every consecutive watermark breach */ |
| unsigned int boost_up_coeff; |
| unsigned int boost_down_coeff; |
| |
| /* Define the watermark bounds when applied to the current avg */ |
| unsigned int boost_up_threshold; |
| unsigned int boost_down_threshold; |
| |
| /* |
| * Threshold of activity (cycles translated to kHz) below which the |
| * CPU frequency isn't to be taken into account. This is to avoid |
| * increasing the EMC frequency when the CPU is very busy but not |
| * accessing the bus often. |
| */ |
| u32 avg_dependency_threshold; |
| }; |
| |
| enum tegra_actmon_device { |
| MCALL = 0, |
| MCCPU, |
| }; |
| |
| static const struct tegra_devfreq_device_config tegra124_device_configs[] = { |
| { |
| /* MCALL: All memory accesses (including from the CPUs) */ |
| .offset = 0x1c0, |
| .irq_mask = 1 << 26, |
| .boost_up_coeff = 200, |
| .boost_down_coeff = 50, |
| .boost_up_threshold = 60, |
| .boost_down_threshold = 40, |
| }, |
| { |
| /* MCCPU: memory accesses from the CPUs */ |
| .offset = 0x200, |
| .irq_mask = 1 << 25, |
| .boost_up_coeff = 800, |
| .boost_down_coeff = 40, |
| .boost_up_threshold = 27, |
| .boost_down_threshold = 10, |
| .avg_dependency_threshold = 16000, /* 16MHz in kHz units */ |
| }, |
| }; |
| |
| static const struct tegra_devfreq_device_config tegra30_device_configs[] = { |
| { |
| /* MCALL: All memory accesses (including from the CPUs) */ |
| .offset = 0x1c0, |
| .irq_mask = 1 << 26, |
| .boost_up_coeff = 200, |
| .boost_down_coeff = 50, |
| .boost_up_threshold = 20, |
| .boost_down_threshold = 10, |
| }, |
| { |
| /* MCCPU: memory accesses from the CPUs */ |
| .offset = 0x200, |
| .irq_mask = 1 << 25, |
| .boost_up_coeff = 800, |
| .boost_down_coeff = 40, |
| .boost_up_threshold = 27, |
| .boost_down_threshold = 10, |
| .avg_dependency_threshold = 16000, /* 16MHz in kHz units */ |
| }, |
| }; |
| |
| /** |
| * struct tegra_devfreq_device - state specific to an ACTMON device |
| * |
| * Frequencies are in kHz. |
| */ |
| struct tegra_devfreq_device { |
| const struct tegra_devfreq_device_config *config; |
| void __iomem *regs; |
| |
| /* Average event count sampled in the last interrupt */ |
| u32 avg_count; |
| |
| /* |
| * Extra frequency to increase the target by due to consecutive |
| * watermark breaches. |
| */ |
| unsigned long boost_freq; |
| |
| /* Optimal frequency calculated from the stats for this device */ |
| unsigned long target_freq; |
| }; |
| |
| struct tegra_devfreq_soc_data { |
| const struct tegra_devfreq_device_config *configs; |
| /* Weight value for count measurements */ |
| unsigned int count_weight; |
| }; |
| |
| struct tegra_devfreq { |
| struct devfreq *devfreq; |
| struct opp_table *opp_table; |
| |
| struct reset_control *reset; |
| struct clk *clock; |
| void __iomem *regs; |
| |
| struct clk *emc_clock; |
| unsigned long max_freq; |
| unsigned long cur_freq; |
| struct notifier_block clk_rate_change_nb; |
| |
| struct delayed_work cpufreq_update_work; |
| struct notifier_block cpu_rate_change_nb; |
| |
| struct tegra_devfreq_device devices[2]; |
| |
| unsigned int irq; |
| |
| bool started; |
| |
| const struct tegra_devfreq_soc_data *soc; |
| }; |
| |
| struct tegra_actmon_emc_ratio { |
| unsigned long cpu_freq; |
| unsigned long emc_freq; |
| }; |
| |
| static const struct tegra_actmon_emc_ratio actmon_emc_ratios[] = { |
| { 1400000, KHZ_MAX }, |
| { 1200000, 750000 }, |
| { 1100000, 600000 }, |
| { 1000000, 500000 }, |
| { 800000, 375000 }, |
| { 500000, 200000 }, |
| { 250000, 100000 }, |
| }; |
| |
| static u32 actmon_readl(struct tegra_devfreq *tegra, u32 offset) |
| { |
| return readl_relaxed(tegra->regs + offset); |
| } |
| |
| static void actmon_writel(struct tegra_devfreq *tegra, u32 val, u32 offset) |
| { |
| writel_relaxed(val, tegra->regs + offset); |
| } |
| |
| static u32 device_readl(struct tegra_devfreq_device *dev, u32 offset) |
| { |
| return readl_relaxed(dev->regs + offset); |
| } |
| |
| static void device_writel(struct tegra_devfreq_device *dev, u32 val, |
| u32 offset) |
| { |
| writel_relaxed(val, dev->regs + offset); |
| } |
| |
| static unsigned long do_percent(unsigned long long val, unsigned int pct) |
| { |
| val = val * pct; |
| do_div(val, 100); |
| |
| /* |
| * High freq + high boosting percent + large polling interval are |
| * resulting in integer overflow when watermarks are calculated. |
| */ |
| return min_t(u64, val, U32_MAX); |
| } |
| |
| static void tegra_devfreq_update_avg_wmark(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| u32 avg_band_freq = tegra->max_freq * ACTMON_DEFAULT_AVG_BAND / KHZ; |
| u32 band = avg_band_freq * tegra->devfreq->profile->polling_ms; |
| u32 avg; |
| |
| avg = min(dev->avg_count, U32_MAX - band); |
| device_writel(dev, avg + band, ACTMON_DEV_AVG_UPPER_WMARK); |
| |
| avg = max(dev->avg_count, band); |
| device_writel(dev, avg - band, ACTMON_DEV_AVG_LOWER_WMARK); |
| } |
| |
| static void tegra_devfreq_update_wmark(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| u32 val = tegra->cur_freq * tegra->devfreq->profile->polling_ms; |
| |
| device_writel(dev, do_percent(val, dev->config->boost_up_threshold), |
| ACTMON_DEV_UPPER_WMARK); |
| |
| device_writel(dev, do_percent(val, dev->config->boost_down_threshold), |
| ACTMON_DEV_LOWER_WMARK); |
| } |
| |
| static void actmon_isr_device(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| u32 intr_status, dev_ctrl; |
| |
| dev->avg_count = device_readl(dev, ACTMON_DEV_AVG_COUNT); |
| tegra_devfreq_update_avg_wmark(tegra, dev); |
| |
| intr_status = device_readl(dev, ACTMON_DEV_INTR_STATUS); |
| dev_ctrl = device_readl(dev, ACTMON_DEV_CTRL); |
| |
| if (intr_status & ACTMON_DEV_INTR_CONSECUTIVE_UPPER) { |
| /* |
| * new_boost = min(old_boost * up_coef + step, max_freq) |
| */ |
| dev->boost_freq = do_percent(dev->boost_freq, |
| dev->config->boost_up_coeff); |
| dev->boost_freq += ACTMON_BOOST_FREQ_STEP; |
| |
| dev_ctrl |= ACTMON_DEV_CTRL_CONSECUTIVE_BELOW_WMARK_EN; |
| |
| if (dev->boost_freq >= tegra->max_freq) { |
| dev_ctrl &= ~ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_EN; |
| dev->boost_freq = tegra->max_freq; |
| } |
| } else if (intr_status & ACTMON_DEV_INTR_CONSECUTIVE_LOWER) { |
| /* |
| * new_boost = old_boost * down_coef |
| * or 0 if (old_boost * down_coef < step / 2) |
| */ |
| dev->boost_freq = do_percent(dev->boost_freq, |
| dev->config->boost_down_coeff); |
| |
| dev_ctrl |= ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_EN; |
| |
| if (dev->boost_freq < (ACTMON_BOOST_FREQ_STEP >> 1)) { |
| dev_ctrl &= ~ACTMON_DEV_CTRL_CONSECUTIVE_BELOW_WMARK_EN; |
| dev->boost_freq = 0; |
| } |
| } |
| |
| device_writel(dev, dev_ctrl, ACTMON_DEV_CTRL); |
| |
| device_writel(dev, ACTMON_INTR_STATUS_CLEAR, ACTMON_DEV_INTR_STATUS); |
| } |
| |
| static unsigned long actmon_cpu_to_emc_rate(struct tegra_devfreq *tegra, |
| unsigned long cpu_freq) |
| { |
| unsigned int i; |
| const struct tegra_actmon_emc_ratio *ratio = actmon_emc_ratios; |
| |
| for (i = 0; i < ARRAY_SIZE(actmon_emc_ratios); i++, ratio++) { |
| if (cpu_freq >= ratio->cpu_freq) { |
| if (ratio->emc_freq >= tegra->max_freq) |
| return tegra->max_freq; |
| else |
| return ratio->emc_freq; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static unsigned long actmon_device_target_freq(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| unsigned int avg_sustain_coef; |
| unsigned long target_freq; |
| |
| target_freq = dev->avg_count / tegra->devfreq->profile->polling_ms; |
| avg_sustain_coef = 100 * 100 / dev->config->boost_up_threshold; |
| target_freq = do_percent(target_freq, avg_sustain_coef); |
| |
| return target_freq; |
| } |
| |
| static void actmon_update_target(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| unsigned long cpu_freq = 0; |
| unsigned long static_cpu_emc_freq = 0; |
| |
| dev->target_freq = actmon_device_target_freq(tegra, dev); |
| |
| if (dev->config->avg_dependency_threshold && |
| dev->config->avg_dependency_threshold <= dev->target_freq) { |
| cpu_freq = cpufreq_quick_get(0); |
| static_cpu_emc_freq = actmon_cpu_to_emc_rate(tegra, cpu_freq); |
| |
| dev->target_freq += dev->boost_freq; |
| dev->target_freq = max(dev->target_freq, static_cpu_emc_freq); |
| } else { |
| dev->target_freq += dev->boost_freq; |
| } |
| } |
| |
| static irqreturn_t actmon_thread_isr(int irq, void *data) |
| { |
| struct tegra_devfreq *tegra = data; |
| bool handled = false; |
| unsigned int i; |
| u32 val; |
| |
| mutex_lock(&tegra->devfreq->lock); |
| |
| val = actmon_readl(tegra, ACTMON_GLB_STATUS); |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++) { |
| if (val & tegra->devices[i].config->irq_mask) { |
| actmon_isr_device(tegra, tegra->devices + i); |
| handled = true; |
| } |
| } |
| |
| if (handled) |
| update_devfreq(tegra->devfreq); |
| |
| mutex_unlock(&tegra->devfreq->lock); |
| |
| return handled ? IRQ_HANDLED : IRQ_NONE; |
| } |
| |
| static int tegra_actmon_clk_notify_cb(struct notifier_block *nb, |
| unsigned long action, void *ptr) |
| { |
| struct clk_notifier_data *data = ptr; |
| struct tegra_devfreq *tegra; |
| struct tegra_devfreq_device *dev; |
| unsigned int i; |
| |
| if (action != POST_RATE_CHANGE) |
| return NOTIFY_OK; |
| |
| tegra = container_of(nb, struct tegra_devfreq, clk_rate_change_nb); |
| |
| tegra->cur_freq = data->new_rate / KHZ; |
| |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++) { |
| dev = &tegra->devices[i]; |
| |
| tegra_devfreq_update_wmark(tegra, dev); |
| } |
| |
| return NOTIFY_OK; |
| } |
| |
| static void tegra_actmon_delayed_update(struct work_struct *work) |
| { |
| struct tegra_devfreq *tegra = container_of(work, struct tegra_devfreq, |
| cpufreq_update_work.work); |
| |
| mutex_lock(&tegra->devfreq->lock); |
| update_devfreq(tegra->devfreq); |
| mutex_unlock(&tegra->devfreq->lock); |
| } |
| |
| static unsigned long |
| tegra_actmon_cpufreq_contribution(struct tegra_devfreq *tegra, |
| unsigned int cpu_freq) |
| { |
| struct tegra_devfreq_device *actmon_dev = &tegra->devices[MCCPU]; |
| unsigned long static_cpu_emc_freq, dev_freq; |
| |
| dev_freq = actmon_device_target_freq(tegra, actmon_dev); |
| |
| /* check whether CPU's freq is taken into account at all */ |
| if (dev_freq < actmon_dev->config->avg_dependency_threshold) |
| return 0; |
| |
| static_cpu_emc_freq = actmon_cpu_to_emc_rate(tegra, cpu_freq); |
| |
| if (dev_freq + actmon_dev->boost_freq >= static_cpu_emc_freq) |
| return 0; |
| |
| return static_cpu_emc_freq; |
| } |
| |
| static int tegra_actmon_cpu_notify_cb(struct notifier_block *nb, |
| unsigned long action, void *ptr) |
| { |
| struct cpufreq_freqs *freqs = ptr; |
| struct tegra_devfreq *tegra; |
| unsigned long old, new, delay; |
| |
| if (action != CPUFREQ_POSTCHANGE) |
| return NOTIFY_OK; |
| |
| tegra = container_of(nb, struct tegra_devfreq, cpu_rate_change_nb); |
| |
| /* |
| * Quickly check whether CPU frequency should be taken into account |
| * at all, without blocking CPUFreq's core. |
| */ |
| if (mutex_trylock(&tegra->devfreq->lock)) { |
| old = tegra_actmon_cpufreq_contribution(tegra, freqs->old); |
| new = tegra_actmon_cpufreq_contribution(tegra, freqs->new); |
| mutex_unlock(&tegra->devfreq->lock); |
| |
| /* |
| * If CPU's frequency shouldn't be taken into account at |
| * the moment, then there is no need to update the devfreq's |
| * state because ISR will re-check CPU's frequency on the |
| * next interrupt. |
| */ |
| if (old == new) |
| return NOTIFY_OK; |
| } |
| |
| /* |
| * CPUFreq driver should support CPUFREQ_ASYNC_NOTIFICATION in order |
| * to allow asynchronous notifications. This means we can't block |
| * here for too long, otherwise CPUFreq's core will complain with a |
| * warning splat. |
| */ |
| delay = msecs_to_jiffies(ACTMON_SAMPLING_PERIOD); |
| schedule_delayed_work(&tegra->cpufreq_update_work, delay); |
| |
| return NOTIFY_OK; |
| } |
| |
| static void tegra_actmon_configure_device(struct tegra_devfreq *tegra, |
| struct tegra_devfreq_device *dev) |
| { |
| u32 val = 0; |
| |
| /* reset boosting on governor's restart */ |
| dev->boost_freq = 0; |
| |
| dev->target_freq = tegra->cur_freq; |
| |
| dev->avg_count = tegra->cur_freq * tegra->devfreq->profile->polling_ms; |
| device_writel(dev, dev->avg_count, ACTMON_DEV_INIT_AVG); |
| |
| tegra_devfreq_update_avg_wmark(tegra, dev); |
| tegra_devfreq_update_wmark(tegra, dev); |
| |
| device_writel(dev, tegra->soc->count_weight, ACTMON_DEV_COUNT_WEIGHT); |
| device_writel(dev, ACTMON_INTR_STATUS_CLEAR, ACTMON_DEV_INTR_STATUS); |
| |
| val |= ACTMON_DEV_CTRL_ENB_PERIODIC; |
| val |= (ACTMON_AVERAGE_WINDOW_LOG2 - 1) |
| << ACTMON_DEV_CTRL_K_VAL_SHIFT; |
| val |= (ACTMON_BELOW_WMARK_WINDOW - 1) |
| << ACTMON_DEV_CTRL_CONSECUTIVE_BELOW_WMARK_NUM_SHIFT; |
| val |= (ACTMON_ABOVE_WMARK_WINDOW - 1) |
| << ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_NUM_SHIFT; |
| val |= ACTMON_DEV_CTRL_AVG_ABOVE_WMARK_EN; |
| val |= ACTMON_DEV_CTRL_AVG_BELOW_WMARK_EN; |
| val |= ACTMON_DEV_CTRL_CONSECUTIVE_ABOVE_WMARK_EN; |
| val |= ACTMON_DEV_CTRL_ENB; |
| |
| device_writel(dev, val, ACTMON_DEV_CTRL); |
| } |
| |
| static void tegra_actmon_stop_devices(struct tegra_devfreq *tegra) |
| { |
| struct tegra_devfreq_device *dev = tegra->devices; |
| unsigned int i; |
| |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++, dev++) { |
| device_writel(dev, ACTMON_DEV_CTRL_STOP, ACTMON_DEV_CTRL); |
| device_writel(dev, ACTMON_INTR_STATUS_CLEAR, |
| ACTMON_DEV_INTR_STATUS); |
| } |
| } |
| |
| static int tegra_actmon_resume(struct tegra_devfreq *tegra) |
| { |
| unsigned int i; |
| int err; |
| |
| if (!tegra->devfreq->profile->polling_ms || !tegra->started) |
| return 0; |
| |
| actmon_writel(tegra, tegra->devfreq->profile->polling_ms - 1, |
| ACTMON_GLB_PERIOD_CTRL); |
| |
| /* |
| * CLK notifications are needed in order to reconfigure the upper |
| * consecutive watermark in accordance to the actual clock rate |
| * to avoid unnecessary upper interrupts. |
| */ |
| err = clk_notifier_register(tegra->emc_clock, |
| &tegra->clk_rate_change_nb); |
| if (err) { |
| dev_err(tegra->devfreq->dev.parent, |
| "Failed to register rate change notifier\n"); |
| return err; |
| } |
| |
| tegra->cur_freq = clk_get_rate(tegra->emc_clock) / KHZ; |
| |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++) |
| tegra_actmon_configure_device(tegra, &tegra->devices[i]); |
| |
| /* |
| * We are estimating CPU's memory bandwidth requirement based on |
| * amount of memory accesses and system's load, judging by CPU's |
| * frequency. We also don't want to receive events about CPU's |
| * frequency transaction when governor is stopped, hence notifier |
| * is registered dynamically. |
| */ |
| err = cpufreq_register_notifier(&tegra->cpu_rate_change_nb, |
| CPUFREQ_TRANSITION_NOTIFIER); |
| if (err) { |
| dev_err(tegra->devfreq->dev.parent, |
| "Failed to register rate change notifier: %d\n", err); |
| goto err_stop; |
| } |
| |
| enable_irq(tegra->irq); |
| |
| return 0; |
| |
| err_stop: |
| tegra_actmon_stop_devices(tegra); |
| |
| clk_notifier_unregister(tegra->emc_clock, &tegra->clk_rate_change_nb); |
| |
| return err; |
| } |
| |
| static int tegra_actmon_start(struct tegra_devfreq *tegra) |
| { |
| int ret = 0; |
| |
| if (!tegra->started) { |
| tegra->started = true; |
| |
| ret = tegra_actmon_resume(tegra); |
| if (ret) |
| tegra->started = false; |
| } |
| |
| return ret; |
| } |
| |
| static void tegra_actmon_pause(struct tegra_devfreq *tegra) |
| { |
| if (!tegra->devfreq->profile->polling_ms || !tegra->started) |
| return; |
| |
| disable_irq(tegra->irq); |
| |
| cpufreq_unregister_notifier(&tegra->cpu_rate_change_nb, |
| CPUFREQ_TRANSITION_NOTIFIER); |
| |
| cancel_delayed_work_sync(&tegra->cpufreq_update_work); |
| |
| tegra_actmon_stop_devices(tegra); |
| |
| clk_notifier_unregister(tegra->emc_clock, &tegra->clk_rate_change_nb); |
| } |
| |
| static void tegra_actmon_stop(struct tegra_devfreq *tegra) |
| { |
| tegra_actmon_pause(tegra); |
| tegra->started = false; |
| } |
| |
| static int tegra_devfreq_target(struct device *dev, unsigned long *freq, |
| u32 flags) |
| { |
| struct dev_pm_opp *opp; |
| int ret; |
| |
| opp = devfreq_recommended_opp(dev, freq, flags); |
| if (IS_ERR(opp)) { |
| dev_err(dev, "Failed to find opp for %lu Hz\n", *freq); |
| return PTR_ERR(opp); |
| } |
| |
| ret = dev_pm_opp_set_opp(dev, opp); |
| dev_pm_opp_put(opp); |
| |
| return ret; |
| } |
| |
| static int tegra_devfreq_get_dev_status(struct device *dev, |
| struct devfreq_dev_status *stat) |
| { |
| struct tegra_devfreq *tegra = dev_get_drvdata(dev); |
| struct tegra_devfreq_device *actmon_dev; |
| unsigned long cur_freq; |
| |
| cur_freq = READ_ONCE(tegra->cur_freq); |
| |
| /* To be used by the tegra governor */ |
| stat->private_data = tegra; |
| |
| /* The below are to be used by the other governors */ |
| stat->current_frequency = cur_freq * KHZ; |
| |
| actmon_dev = &tegra->devices[MCALL]; |
| |
| /* Number of cycles spent on memory access */ |
| stat->busy_time = device_readl(actmon_dev, ACTMON_DEV_AVG_COUNT); |
| |
| /* The bus can be considered to be saturated way before 100% */ |
| stat->busy_time *= 100 / BUS_SATURATION_RATIO; |
| |
| /* Number of cycles in a sampling period */ |
| stat->total_time = tegra->devfreq->profile->polling_ms * cur_freq; |
| |
| stat->busy_time = min(stat->busy_time, stat->total_time); |
| |
| return 0; |
| } |
| |
| static struct devfreq_dev_profile tegra_devfreq_profile = { |
| .polling_ms = ACTMON_SAMPLING_PERIOD, |
| .target = tegra_devfreq_target, |
| .get_dev_status = tegra_devfreq_get_dev_status, |
| }; |
| |
| static int tegra_governor_get_target(struct devfreq *devfreq, |
| unsigned long *freq) |
| { |
| struct devfreq_dev_status *stat; |
| struct tegra_devfreq *tegra; |
| struct tegra_devfreq_device *dev; |
| unsigned long target_freq = 0; |
| unsigned int i; |
| int err; |
| |
| err = devfreq_update_stats(devfreq); |
| if (err) |
| return err; |
| |
| stat = &devfreq->last_status; |
| |
| tegra = stat->private_data; |
| |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++) { |
| dev = &tegra->devices[i]; |
| |
| actmon_update_target(tegra, dev); |
| |
| target_freq = max(target_freq, dev->target_freq); |
| } |
| |
| /* |
| * tegra-devfreq driver operates with KHz units, while OPP table |
| * entries use Hz units. Hence we need to convert the units for the |
| * devfreq core. |
| */ |
| *freq = target_freq * KHZ; |
| |
| return 0; |
| } |
| |
| static int tegra_governor_event_handler(struct devfreq *devfreq, |
| unsigned int event, void *data) |
| { |
| struct tegra_devfreq *tegra = dev_get_drvdata(devfreq->dev.parent); |
| unsigned int *new_delay = data; |
| int ret = 0; |
| |
| /* |
| * Couple devfreq-device with the governor early because it is |
| * needed at the moment of governor's start (used by ISR). |
| */ |
| tegra->devfreq = devfreq; |
| |
| switch (event) { |
| case DEVFREQ_GOV_START: |
| devfreq_monitor_start(devfreq); |
| ret = tegra_actmon_start(tegra); |
| break; |
| |
| case DEVFREQ_GOV_STOP: |
| tegra_actmon_stop(tegra); |
| devfreq_monitor_stop(devfreq); |
| break; |
| |
| case DEVFREQ_GOV_UPDATE_INTERVAL: |
| /* |
| * ACTMON hardware supports up to 256 milliseconds for the |
| * sampling period. |
| */ |
| if (*new_delay > 256) { |
| ret = -EINVAL; |
| break; |
| } |
| |
| tegra_actmon_pause(tegra); |
| devfreq_update_interval(devfreq, new_delay); |
| ret = tegra_actmon_resume(tegra); |
| break; |
| |
| case DEVFREQ_GOV_SUSPEND: |
| tegra_actmon_stop(tegra); |
| devfreq_monitor_suspend(devfreq); |
| break; |
| |
| case DEVFREQ_GOV_RESUME: |
| devfreq_monitor_resume(devfreq); |
| ret = tegra_actmon_start(tegra); |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static struct devfreq_governor tegra_devfreq_governor = { |
| .name = "tegra_actmon", |
| .attrs = DEVFREQ_GOV_ATTR_POLLING_INTERVAL, |
| .flags = DEVFREQ_GOV_FLAG_IMMUTABLE |
| | DEVFREQ_GOV_FLAG_IRQ_DRIVEN, |
| .get_target_freq = tegra_governor_get_target, |
| .event_handler = tegra_governor_event_handler, |
| }; |
| |
| static int tegra_devfreq_probe(struct platform_device *pdev) |
| { |
| u32 hw_version = BIT(tegra_sku_info.soc_speedo_id); |
| struct tegra_devfreq_device *dev; |
| struct tegra_devfreq *tegra; |
| struct devfreq *devfreq; |
| unsigned int i; |
| long rate; |
| int err; |
| |
| tegra = devm_kzalloc(&pdev->dev, sizeof(*tegra), GFP_KERNEL); |
| if (!tegra) |
| return -ENOMEM; |
| |
| tegra->soc = of_device_get_match_data(&pdev->dev); |
| |
| tegra->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(tegra->regs)) |
| return PTR_ERR(tegra->regs); |
| |
| tegra->reset = devm_reset_control_get(&pdev->dev, "actmon"); |
| if (IS_ERR(tegra->reset)) { |
| dev_err(&pdev->dev, "Failed to get reset\n"); |
| return PTR_ERR(tegra->reset); |
| } |
| |
| tegra->clock = devm_clk_get(&pdev->dev, "actmon"); |
| if (IS_ERR(tegra->clock)) { |
| dev_err(&pdev->dev, "Failed to get actmon clock\n"); |
| return PTR_ERR(tegra->clock); |
| } |
| |
| tegra->emc_clock = devm_clk_get(&pdev->dev, "emc"); |
| if (IS_ERR(tegra->emc_clock)) |
| return dev_err_probe(&pdev->dev, PTR_ERR(tegra->emc_clock), |
| "Failed to get emc clock\n"); |
| |
| err = platform_get_irq(pdev, 0); |
| if (err < 0) |
| return err; |
| |
| tegra->irq = err; |
| |
| irq_set_status_flags(tegra->irq, IRQ_NOAUTOEN); |
| |
| err = devm_request_threaded_irq(&pdev->dev, tegra->irq, NULL, |
| actmon_thread_isr, IRQF_ONESHOT, |
| "tegra-devfreq", tegra); |
| if (err) { |
| dev_err(&pdev->dev, "Interrupt request failed: %d\n", err); |
| return err; |
| } |
| |
| tegra->opp_table = dev_pm_opp_set_supported_hw(&pdev->dev, |
| &hw_version, 1); |
| err = PTR_ERR_OR_ZERO(tegra->opp_table); |
| if (err) { |
| dev_err(&pdev->dev, "Failed to set supported HW: %d\n", err); |
| return err; |
| } |
| |
| err = dev_pm_opp_of_add_table_noclk(&pdev->dev, 0); |
| if (err) { |
| dev_err(&pdev->dev, "Failed to add OPP table: %d\n", err); |
| goto put_hw; |
| } |
| |
| err = clk_prepare_enable(tegra->clock); |
| if (err) { |
| dev_err(&pdev->dev, |
| "Failed to prepare and enable ACTMON clock\n"); |
| goto remove_table; |
| } |
| |
| err = reset_control_reset(tegra->reset); |
| if (err) { |
| dev_err(&pdev->dev, "Failed to reset hardware: %d\n", err); |
| goto disable_clk; |
| } |
| |
| rate = clk_round_rate(tegra->emc_clock, ULONG_MAX); |
| if (rate < 0) { |
| dev_err(&pdev->dev, "Failed to round clock rate: %ld\n", rate); |
| err = rate; |
| goto disable_clk; |
| } |
| |
| tegra->max_freq = rate / KHZ; |
| |
| for (i = 0; i < ARRAY_SIZE(tegra->devices); i++) { |
| dev = tegra->devices + i; |
| dev->config = tegra->soc->configs + i; |
| dev->regs = tegra->regs + dev->config->offset; |
| } |
| |
| platform_set_drvdata(pdev, tegra); |
| |
| tegra->clk_rate_change_nb.notifier_call = tegra_actmon_clk_notify_cb; |
| tegra->cpu_rate_change_nb.notifier_call = tegra_actmon_cpu_notify_cb; |
| |
| INIT_DELAYED_WORK(&tegra->cpufreq_update_work, |
| tegra_actmon_delayed_update); |
| |
| err = devfreq_add_governor(&tegra_devfreq_governor); |
| if (err) { |
| dev_err(&pdev->dev, "Failed to add governor: %d\n", err); |
| goto remove_opps; |
| } |
| |
| tegra_devfreq_profile.initial_freq = clk_get_rate(tegra->emc_clock); |
| |
| devfreq = devfreq_add_device(&pdev->dev, &tegra_devfreq_profile, |
| "tegra_actmon", NULL); |
| if (IS_ERR(devfreq)) { |
| err = PTR_ERR(devfreq); |
| goto remove_governor; |
| } |
| |
| return 0; |
| |
| remove_governor: |
| devfreq_remove_governor(&tegra_devfreq_governor); |
| |
| remove_opps: |
| dev_pm_opp_remove_all_dynamic(&pdev->dev); |
| |
| reset_control_reset(tegra->reset); |
| disable_clk: |
| clk_disable_unprepare(tegra->clock); |
| remove_table: |
| dev_pm_opp_of_remove_table(&pdev->dev); |
| put_hw: |
| dev_pm_opp_put_supported_hw(tegra->opp_table); |
| |
| return err; |
| } |
| |
| static int tegra_devfreq_remove(struct platform_device *pdev) |
| { |
| struct tegra_devfreq *tegra = platform_get_drvdata(pdev); |
| |
| devfreq_remove_device(tegra->devfreq); |
| devfreq_remove_governor(&tegra_devfreq_governor); |
| |
| reset_control_reset(tegra->reset); |
| clk_disable_unprepare(tegra->clock); |
| |
| dev_pm_opp_of_remove_table(&pdev->dev); |
| dev_pm_opp_put_supported_hw(tegra->opp_table); |
| |
| return 0; |
| } |
| |
| static const struct tegra_devfreq_soc_data tegra124_soc = { |
| .configs = tegra124_device_configs, |
| |
| /* |
| * Activity counter is incremented every 256 memory transactions, |
| * and each transaction takes 4 EMC clocks. |
| */ |
| .count_weight = 4 * 256, |
| }; |
| |
| static const struct tegra_devfreq_soc_data tegra30_soc = { |
| .configs = tegra30_device_configs, |
| .count_weight = 2 * 256, |
| }; |
| |
| static const struct of_device_id tegra_devfreq_of_match[] = { |
| { .compatible = "nvidia,tegra30-actmon", .data = &tegra30_soc, }, |
| { .compatible = "nvidia,tegra124-actmon", .data = &tegra124_soc, }, |
| { }, |
| }; |
| |
| MODULE_DEVICE_TABLE(of, tegra_devfreq_of_match); |
| |
| static struct platform_driver tegra_devfreq_driver = { |
| .probe = tegra_devfreq_probe, |
| .remove = tegra_devfreq_remove, |
| .driver = { |
| .name = "tegra-devfreq", |
| .of_match_table = tegra_devfreq_of_match, |
| }, |
| }; |
| module_platform_driver(tegra_devfreq_driver); |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_DESCRIPTION("Tegra devfreq driver"); |
| MODULE_AUTHOR("Tomeu Vizoso <tomeu.vizoso@collabora.com>"); |