| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright (C) 2015 Broadcom | |
| */ | |
| /** | |
| * DOC: VC4 HVS module. | |
| * | |
| * The Hardware Video Scaler (HVS) is the piece of hardware that does | |
| * translation, scaling, colorspace conversion, and compositing of | |
| * pixels stored in framebuffers into a FIFO of pixels going out to | |
| * the Pixel Valve (CRTC). It operates at the system clock rate (the | |
| * system audio clock gate, specifically), which is much higher than | |
| * the pixel clock rate. | |
| * | |
| * There is a single global HVS, with multiple output FIFOs that can | |
| * be consumed by the PVs. This file just manages the resources for | |
| * the HVS, while the vc4_crtc.c code actually drives HVS setup for | |
| * each CRTC. | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/clk.h> | |
| #include <linux/component.h> | |
| #include <linux/platform_device.h> | |
| #include <drm/drm_atomic_helper.h> | |
| #include <drm/drm_drv.h> | |
| #include <drm/drm_vblank.h> | |
| #include <soc/bcm2835/raspberrypi-firmware.h> | |
| #include "vc4_drv.h" | |
| #include "vc4_regs.h" | |
| static const struct debugfs_reg32 hvs_regs[] = { | |
| VC4_REG32(SCALER_DISPCTRL), | |
| VC4_REG32(SCALER_DISPSTAT), | |
| VC4_REG32(SCALER_DISPID), | |
| VC4_REG32(SCALER_DISPECTRL), | |
| VC4_REG32(SCALER_DISPPROF), | |
| VC4_REG32(SCALER_DISPDITHER), | |
| VC4_REG32(SCALER_DISPEOLN), | |
| VC4_REG32(SCALER_DISPLIST0), | |
| VC4_REG32(SCALER_DISPLIST1), | |
| VC4_REG32(SCALER_DISPLIST2), | |
| VC4_REG32(SCALER_DISPLSTAT), | |
| VC4_REG32(SCALER_DISPLACT0), | |
| VC4_REG32(SCALER_DISPLACT1), | |
| VC4_REG32(SCALER_DISPLACT2), | |
| VC4_REG32(SCALER_DISPCTRL0), | |
| VC4_REG32(SCALER_DISPBKGND0), | |
| VC4_REG32(SCALER_DISPSTAT0), | |
| VC4_REG32(SCALER_DISPBASE0), | |
| VC4_REG32(SCALER_DISPCTRL1), | |
| VC4_REG32(SCALER_DISPBKGND1), | |
| VC4_REG32(SCALER_DISPSTAT1), | |
| VC4_REG32(SCALER_DISPBASE1), | |
| VC4_REG32(SCALER_DISPCTRL2), | |
| VC4_REG32(SCALER_DISPBKGND2), | |
| VC4_REG32(SCALER_DISPSTAT2), | |
| VC4_REG32(SCALER_DISPBASE2), | |
| VC4_REG32(SCALER_DISPALPHA2), | |
| VC4_REG32(SCALER_OLEDOFFS), | |
| VC4_REG32(SCALER_OLEDCOEF0), | |
| VC4_REG32(SCALER_OLEDCOEF1), | |
| VC4_REG32(SCALER_OLEDCOEF2), | |
| }; | |
| void vc4_hvs_dump_state(struct vc4_hvs *hvs) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| struct drm_printer p = drm_info_printer(&hvs->pdev->dev); | |
| int idx, i; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return; | |
| drm_print_regset32(&p, &hvs->regset); | |
| DRM_INFO("HVS ctx:\n"); | |
| for (i = 0; i < 64; i += 4) { | |
| DRM_INFO("0x%08x (%s): 0x%08x 0x%08x 0x%08x 0x%08x\n", | |
| i * 4, i < HVS_BOOTLOADER_DLIST_END ? "B" : "D", | |
| readl((u32 __iomem *)hvs->dlist + i + 0), | |
| readl((u32 __iomem *)hvs->dlist + i + 1), | |
| readl((u32 __iomem *)hvs->dlist + i + 2), | |
| readl((u32 __iomem *)hvs->dlist + i + 3)); | |
| } | |
| drm_dev_exit(idx); | |
| } | |
| static int vc4_hvs_debugfs_underrun(struct seq_file *m, void *data) | |
| { | |
| struct drm_debugfs_entry *entry = m->private; | |
| struct drm_device *dev = entry->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct drm_printer p = drm_seq_file_printer(m); | |
| drm_printf(&p, "%d\n", atomic_read(&vc4->underrun)); | |
| return 0; | |
| } | |
| static int vc4_hvs_debugfs_dlist(struct seq_file *m, void *data) | |
| { | |
| struct drm_debugfs_entry *entry = m->private; | |
| struct drm_device *dev = entry->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| struct drm_printer p = drm_seq_file_printer(m); | |
| unsigned int next_entry_start = 0; | |
| unsigned int i, j; | |
| u32 dlist_word, dispstat; | |
| for (i = 0; i < SCALER_CHANNELS_COUNT; i++) { | |
| dispstat = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(i)), | |
| SCALER_DISPSTATX_MODE); | |
| if (dispstat == SCALER_DISPSTATX_MODE_DISABLED || | |
| dispstat == SCALER_DISPSTATX_MODE_EOF) { | |
| drm_printf(&p, "HVS chan %u disabled\n", i); | |
| continue; | |
| } | |
| drm_printf(&p, "HVS chan %u:\n", i); | |
| for (j = HVS_READ(SCALER_DISPLISTX(i)); j < 256; j++) { | |
| dlist_word = readl((u32 __iomem *)vc4->hvs->dlist + j); | |
| drm_printf(&p, "dlist: %02d: 0x%08x\n", j, | |
| dlist_word); | |
| if (!next_entry_start || | |
| next_entry_start == j) { | |
| if (dlist_word & SCALER_CTL0_END) | |
| break; | |
| next_entry_start = j + | |
| VC4_GET_FIELD(dlist_word, | |
| SCALER_CTL0_SIZE); | |
| } | |
| } | |
| } | |
| return 0; | |
| } | |
| /* The filter kernel is composed of dwords each containing 3 9-bit | |
| * signed integers packed next to each other. | |
| */ | |
| #define VC4_INT_TO_COEFF(coeff) (coeff & 0x1ff) | |
| #define VC4_PPF_FILTER_WORD(c0, c1, c2) \ | |
| ((((c0) & 0x1ff) << 0) | \ | |
| (((c1) & 0x1ff) << 9) | \ | |
| (((c2) & 0x1ff) << 18)) | |
| /* The whole filter kernel is arranged as the coefficients 0-16 going | |
| * up, then a pad, then 17-31 going down and reversed within the | |
| * dwords. This means that a linear phase kernel (where it's | |
| * symmetrical at the boundary between 15 and 16) has the last 5 | |
| * dwords matching the first 5, but reversed. | |
| */ | |
| #define VC4_LINEAR_PHASE_KERNEL(c0, c1, c2, c3, c4, c5, c6, c7, c8, \ | |
| c9, c10, c11, c12, c13, c14, c15) \ | |
| {VC4_PPF_FILTER_WORD(c0, c1, c2), \ | |
| VC4_PPF_FILTER_WORD(c3, c4, c5), \ | |
| VC4_PPF_FILTER_WORD(c6, c7, c8), \ | |
| VC4_PPF_FILTER_WORD(c9, c10, c11), \ | |
| VC4_PPF_FILTER_WORD(c12, c13, c14), \ | |
| VC4_PPF_FILTER_WORD(c15, c15, 0)} | |
| #define VC4_LINEAR_PHASE_KERNEL_DWORDS 6 | |
| #define VC4_KERNEL_DWORDS (VC4_LINEAR_PHASE_KERNEL_DWORDS * 2 - 1) | |
| /* Recommended B=1/3, C=1/3 filter choice from Mitchell/Netravali. | |
| * http://www.cs.utexas.edu/~fussell/courses/cs384g/lectures/mitchell/Mitchell.pdf | |
| */ | |
| static const u32 mitchell_netravali_1_3_1_3_kernel[] = | |
| VC4_LINEAR_PHASE_KERNEL(0, -2, -6, -8, -10, -8, -3, 2, 18, | |
| 50, 82, 119, 155, 187, 213, 227); | |
| static int vc4_hvs_upload_linear_kernel(struct vc4_hvs *hvs, | |
| struct drm_mm_node *space, | |
| const u32 *kernel) | |
| { | |
| int ret, i; | |
| u32 __iomem *dst_kernel; | |
| /* | |
| * NOTE: We don't need a call to drm_dev_enter()/drm_dev_exit() | |
| * here since that function is only called from vc4_hvs_bind(). | |
| */ | |
| ret = drm_mm_insert_node(&hvs->dlist_mm, space, VC4_KERNEL_DWORDS); | |
| if (ret) { | |
| drm_err(&hvs->vc4->base, "Failed to allocate space for filter kernel: %d\n", | |
| ret); | |
| return ret; | |
| } | |
| dst_kernel = hvs->dlist + space->start; | |
| for (i = 0; i < VC4_KERNEL_DWORDS; i++) { | |
| if (i < VC4_LINEAR_PHASE_KERNEL_DWORDS) | |
| writel(kernel[i], &dst_kernel[i]); | |
| else { | |
| writel(kernel[VC4_KERNEL_DWORDS - i - 1], | |
| &dst_kernel[i]); | |
| } | |
| } | |
| return 0; | |
| } | |
| static void vc4_hvs_lut_load(struct vc4_hvs *hvs, | |
| struct vc4_crtc *vc4_crtc) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| struct drm_crtc *crtc = &vc4_crtc->base; | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state); | |
| int idx; | |
| u32 i; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return; | |
| /* The LUT memory is laid out with each HVS channel in order, | |
| * each of which takes 256 writes for R, 256 for G, then 256 | |
| * for B. | |
| */ | |
| HVS_WRITE(SCALER_GAMADDR, | |
| SCALER_GAMADDR_AUTOINC | | |
| (vc4_state->assigned_channel * 3 * crtc->gamma_size)); | |
| for (i = 0; i < crtc->gamma_size; i++) | |
| HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_r[i]); | |
| for (i = 0; i < crtc->gamma_size; i++) | |
| HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_g[i]); | |
| for (i = 0; i < crtc->gamma_size; i++) | |
| HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_b[i]); | |
| drm_dev_exit(idx); | |
| } | |
| static void vc4_hvs_update_gamma_lut(struct vc4_hvs *hvs, | |
| struct vc4_crtc *vc4_crtc) | |
| { | |
| struct drm_crtc_state *crtc_state = vc4_crtc->base.state; | |
| struct drm_color_lut *lut = crtc_state->gamma_lut->data; | |
| u32 length = drm_color_lut_size(crtc_state->gamma_lut); | |
| u32 i; | |
| for (i = 0; i < length; i++) { | |
| vc4_crtc->lut_r[i] = drm_color_lut_extract(lut[i].red, 8); | |
| vc4_crtc->lut_g[i] = drm_color_lut_extract(lut[i].green, 8); | |
| vc4_crtc->lut_b[i] = drm_color_lut_extract(lut[i].blue, 8); | |
| } | |
| vc4_hvs_lut_load(hvs, vc4_crtc); | |
| } | |
| u8 vc4_hvs_get_fifo_frame_count(struct vc4_hvs *hvs, unsigned int fifo) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| u8 field = 0; | |
| int idx; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return 0; | |
| switch (fifo) { | |
| case 0: | |
| field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT1), | |
| SCALER_DISPSTAT1_FRCNT0); | |
| break; | |
| case 1: | |
| field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT1), | |
| SCALER_DISPSTAT1_FRCNT1); | |
| break; | |
| case 2: | |
| field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT2), | |
| SCALER_DISPSTAT2_FRCNT2); | |
| break; | |
| } | |
| drm_dev_exit(idx); | |
| return field; | |
| } | |
| int vc4_hvs_get_fifo_from_output(struct vc4_hvs *hvs, unsigned int output) | |
| { | |
| struct vc4_dev *vc4 = hvs->vc4; | |
| u32 reg; | |
| int ret; | |
| if (!vc4->is_vc5) | |
| return output; | |
| /* | |
| * NOTE: We should probably use drm_dev_enter()/drm_dev_exit() | |
| * here, but this function is only used during the DRM device | |
| * initialization, so we should be fine. | |
| */ | |
| switch (output) { | |
| case 0: | |
| return 0; | |
| case 1: | |
| return 1; | |
| case 2: | |
| reg = HVS_READ(SCALER_DISPECTRL); | |
| ret = FIELD_GET(SCALER_DISPECTRL_DSP2_MUX_MASK, reg); | |
| if (ret == 0) | |
| return 2; | |
| return 0; | |
| case 3: | |
| reg = HVS_READ(SCALER_DISPCTRL); | |
| ret = FIELD_GET(SCALER_DISPCTRL_DSP3_MUX_MASK, reg); | |
| if (ret == 3) | |
| return -EPIPE; | |
| return ret; | |
| case 4: | |
| reg = HVS_READ(SCALER_DISPEOLN); | |
| ret = FIELD_GET(SCALER_DISPEOLN_DSP4_MUX_MASK, reg); | |
| if (ret == 3) | |
| return -EPIPE; | |
| return ret; | |
| case 5: | |
| reg = HVS_READ(SCALER_DISPDITHER); | |
| ret = FIELD_GET(SCALER_DISPDITHER_DSP5_MUX_MASK, reg); | |
| if (ret == 3) | |
| return -EPIPE; | |
| return ret; | |
| default: | |
| return -EPIPE; | |
| } | |
| } | |
| static int vc4_hvs_init_channel(struct vc4_hvs *hvs, struct drm_crtc *crtc, | |
| struct drm_display_mode *mode, bool oneshot) | |
| { | |
| struct vc4_dev *vc4 = hvs->vc4; | |
| struct drm_device *drm = &vc4->base; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state); | |
| unsigned int chan = vc4_crtc_state->assigned_channel; | |
| bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE; | |
| u32 dispbkgndx; | |
| u32 dispctrl; | |
| int idx; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return -ENODEV; | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), 0); | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), SCALER_DISPCTRLX_RESET); | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), 0); | |
| /* Turn on the scaler, which will wait for vstart to start | |
| * compositing. | |
| * When feeding the transposer, we should operate in oneshot | |
| * mode. | |
| */ | |
| dispctrl = SCALER_DISPCTRLX_ENABLE; | |
| dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(chan)); | |
| if (!vc4->is_vc5) { | |
| dispctrl |= VC4_SET_FIELD(mode->hdisplay, | |
| SCALER_DISPCTRLX_WIDTH) | | |
| VC4_SET_FIELD(mode->vdisplay, | |
| SCALER_DISPCTRLX_HEIGHT) | | |
| (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0); | |
| dispbkgndx |= SCALER_DISPBKGND_AUTOHS; | |
| } else { | |
| dispctrl |= VC4_SET_FIELD(mode->hdisplay, | |
| SCALER5_DISPCTRLX_WIDTH) | | |
| VC4_SET_FIELD(mode->vdisplay, | |
| SCALER5_DISPCTRLX_HEIGHT) | | |
| (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0); | |
| dispbkgndx &= ~SCALER5_DISPBKGND_BCK2BCK; | |
| } | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl); | |
| dispbkgndx &= ~SCALER_DISPBKGND_GAMMA; | |
| dispbkgndx &= ~SCALER_DISPBKGND_INTERLACE; | |
| HVS_WRITE(SCALER_DISPBKGNDX(chan), dispbkgndx | | |
| ((!vc4->is_vc5) ? SCALER_DISPBKGND_GAMMA : 0) | | |
| (interlace ? SCALER_DISPBKGND_INTERLACE : 0)); | |
| /* Reload the LUT, since the SRAMs would have been disabled if | |
| * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once. | |
| */ | |
| vc4_hvs_lut_load(hvs, vc4_crtc); | |
| drm_dev_exit(idx); | |
| return 0; | |
| } | |
| void vc4_hvs_stop_channel(struct vc4_hvs *hvs, unsigned int chan) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| int idx; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return; | |
| if (HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_ENABLE) | |
| goto out; | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), | |
| HVS_READ(SCALER_DISPCTRLX(chan)) | SCALER_DISPCTRLX_RESET); | |
| HVS_WRITE(SCALER_DISPCTRLX(chan), | |
| HVS_READ(SCALER_DISPCTRLX(chan)) & ~SCALER_DISPCTRLX_ENABLE); | |
| /* Once we leave, the scaler should be disabled and its fifo empty. */ | |
| WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET); | |
| WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)), | |
| SCALER_DISPSTATX_MODE) != | |
| SCALER_DISPSTATX_MODE_DISABLED); | |
| WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) & | |
| (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) != | |
| SCALER_DISPSTATX_EMPTY); | |
| out: | |
| drm_dev_exit(idx); | |
| } | |
| int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_atomic_state *state) | |
| { | |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state); | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct drm_plane *plane; | |
| unsigned long flags; | |
| const struct drm_plane_state *plane_state; | |
| u32 dlist_count = 0; | |
| int ret; | |
| /* The pixelvalve can only feed one encoder (and encoders are | |
| * 1:1 with connectors.) | |
| */ | |
| if (hweight32(crtc_state->connector_mask) > 1) | |
| return -EINVAL; | |
| drm_atomic_crtc_state_for_each_plane_state(plane, plane_state, crtc_state) | |
| dlist_count += vc4_plane_dlist_size(plane_state); | |
| dlist_count++; /* Account for SCALER_CTL0_END. */ | |
| spin_lock_irqsave(&vc4->hvs->mm_lock, flags); | |
| ret = drm_mm_insert_node(&vc4->hvs->dlist_mm, &vc4_state->mm, | |
| dlist_count); | |
| spin_unlock_irqrestore(&vc4->hvs->mm_lock, flags); | |
| if (ret) | |
| return ret; | |
| return 0; | |
| } | |
| static void vc4_hvs_install_dlist(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state); | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return; | |
| HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel), | |
| vc4_state->mm.start); | |
| drm_dev_exit(idx); | |
| } | |
| static void vc4_hvs_update_dlist(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state); | |
| unsigned long flags; | |
| if (crtc->state->event) { | |
| crtc->state->event->pipe = drm_crtc_index(crtc); | |
| WARN_ON(drm_crtc_vblank_get(crtc) != 0); | |
| spin_lock_irqsave(&dev->event_lock, flags); | |
| if (!vc4_crtc->feeds_txp || vc4_state->txp_armed) { | |
| vc4_crtc->event = crtc->state->event; | |
| crtc->state->event = NULL; | |
| } | |
| spin_unlock_irqrestore(&dev->event_lock, flags); | |
| } | |
| spin_lock_irqsave(&vc4_crtc->irq_lock, flags); | |
| vc4_crtc->current_dlist = vc4_state->mm.start; | |
| spin_unlock_irqrestore(&vc4_crtc->irq_lock, flags); | |
| } | |
| void vc4_hvs_atomic_begin(struct drm_crtc *crtc, | |
| struct drm_atomic_state *state) | |
| { | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state); | |
| unsigned long flags; | |
| spin_lock_irqsave(&vc4_crtc->irq_lock, flags); | |
| vc4_crtc->current_hvs_channel = vc4_state->assigned_channel; | |
| spin_unlock_irqrestore(&vc4_crtc->irq_lock, flags); | |
| } | |
| void vc4_hvs_atomic_enable(struct drm_crtc *crtc, | |
| struct drm_atomic_state *state) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct drm_display_mode *mode = &crtc->state->adjusted_mode; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| bool oneshot = vc4_crtc->feeds_txp; | |
| vc4_hvs_install_dlist(crtc); | |
| vc4_hvs_update_dlist(crtc); | |
| vc4_hvs_init_channel(vc4->hvs, crtc, mode, oneshot); | |
| } | |
| void vc4_hvs_atomic_disable(struct drm_crtc *crtc, | |
| struct drm_atomic_state *state) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state); | |
| unsigned int chan = vc4_state->assigned_channel; | |
| vc4_hvs_stop_channel(vc4->hvs, chan); | |
| } | |
| void vc4_hvs_atomic_flush(struct drm_crtc *crtc, | |
| struct drm_atomic_state *state) | |
| { | |
| struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, | |
| crtc); | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state); | |
| unsigned int channel = vc4_state->assigned_channel; | |
| struct drm_plane *plane; | |
| struct vc4_plane_state *vc4_plane_state; | |
| bool debug_dump_regs = false; | |
| bool enable_bg_fill = false; | |
| u32 __iomem *dlist_start = vc4->hvs->dlist + vc4_state->mm.start; | |
| u32 __iomem *dlist_next = dlist_start; | |
| unsigned int zpos = 0; | |
| bool found = false; | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) { | |
| vc4_crtc_send_vblank(crtc); | |
| return; | |
| } | |
| if (vc4_state->assigned_channel == VC4_HVS_CHANNEL_DISABLED) | |
| return; | |
| if (debug_dump_regs) { | |
| DRM_INFO("CRTC %d HVS before:\n", drm_crtc_index(crtc)); | |
| vc4_hvs_dump_state(hvs); | |
| } | |
| /* Copy all the active planes' dlist contents to the hardware dlist. */ | |
| do { | |
| found = false; | |
| drm_atomic_crtc_for_each_plane(plane, crtc) { | |
| if (plane->state->normalized_zpos != zpos) | |
| continue; | |
| /* Is this the first active plane? */ | |
| if (dlist_next == dlist_start) { | |
| /* We need to enable background fill when a plane | |
| * could be alpha blending from the background, i.e. | |
| * where no other plane is underneath. It suffices to | |
| * consider the first active plane here since we set | |
| * needs_bg_fill such that either the first plane | |
| * already needs it or all planes on top blend from | |
| * the first or a lower plane. | |
| */ | |
| vc4_plane_state = to_vc4_plane_state(plane->state); | |
| enable_bg_fill = vc4_plane_state->needs_bg_fill; | |
| } | |
| dlist_next += vc4_plane_write_dlist(plane, dlist_next); | |
| found = true; | |
| } | |
| zpos++; | |
| } while (found); | |
| writel(SCALER_CTL0_END, dlist_next); | |
| dlist_next++; | |
| WARN_ON_ONCE(dlist_next - dlist_start != vc4_state->mm.size); | |
| if (enable_bg_fill) | |
| /* This sets a black background color fill, as is the case | |
| * with other DRM drivers. | |
| */ | |
| HVS_WRITE(SCALER_DISPBKGNDX(channel), | |
| HVS_READ(SCALER_DISPBKGNDX(channel)) | | |
| SCALER_DISPBKGND_FILL); | |
| /* Only update DISPLIST if the CRTC was already running and is not | |
| * being disabled. | |
| * vc4_crtc_enable() takes care of updating the dlist just after | |
| * re-enabling VBLANK interrupts and before enabling the engine. | |
| * If the CRTC is being disabled, there's no point in updating this | |
| * information. | |
| */ | |
| if (crtc->state->active && old_state->active) { | |
| vc4_hvs_install_dlist(crtc); | |
| vc4_hvs_update_dlist(crtc); | |
| } | |
| if (crtc->state->color_mgmt_changed) { | |
| u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(channel)); | |
| if (crtc->state->gamma_lut) { | |
| vc4_hvs_update_gamma_lut(hvs, vc4_crtc); | |
| dispbkgndx |= SCALER_DISPBKGND_GAMMA; | |
| } else { | |
| /* Unsetting DISPBKGND_GAMMA skips the gamma lut step | |
| * in hardware, which is the same as a linear lut that | |
| * DRM expects us to use in absence of a user lut. | |
| */ | |
| dispbkgndx &= ~SCALER_DISPBKGND_GAMMA; | |
| } | |
| HVS_WRITE(SCALER_DISPBKGNDX(channel), dispbkgndx); | |
| } | |
| if (debug_dump_regs) { | |
| DRM_INFO("CRTC %d HVS after:\n", drm_crtc_index(crtc)); | |
| vc4_hvs_dump_state(hvs); | |
| } | |
| drm_dev_exit(idx); | |
| } | |
| void vc4_hvs_mask_underrun(struct vc4_hvs *hvs, int channel) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| u32 dispctrl; | |
| int idx; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return; | |
| dispctrl = HVS_READ(SCALER_DISPCTRL); | |
| dispctrl &= ~(hvs->vc4->is_vc5 ? SCALER5_DISPCTRL_DSPEISLUR(channel) : | |
| SCALER_DISPCTRL_DSPEISLUR(channel)); | |
| HVS_WRITE(SCALER_DISPCTRL, dispctrl); | |
| drm_dev_exit(idx); | |
| } | |
| void vc4_hvs_unmask_underrun(struct vc4_hvs *hvs, int channel) | |
| { | |
| struct drm_device *drm = &hvs->vc4->base; | |
| u32 dispctrl; | |
| int idx; | |
| if (!drm_dev_enter(drm, &idx)) | |
| return; | |
| dispctrl = HVS_READ(SCALER_DISPCTRL); | |
| dispctrl |= (hvs->vc4->is_vc5 ? SCALER5_DISPCTRL_DSPEISLUR(channel) : | |
| SCALER_DISPCTRL_DSPEISLUR(channel)); | |
| HVS_WRITE(SCALER_DISPSTAT, | |
| SCALER_DISPSTAT_EUFLOW(channel)); | |
| HVS_WRITE(SCALER_DISPCTRL, dispctrl); | |
| drm_dev_exit(idx); | |
| } | |
| static void vc4_hvs_report_underrun(struct drm_device *dev) | |
| { | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| atomic_inc(&vc4->underrun); | |
| DRM_DEV_ERROR(dev->dev, "HVS underrun\n"); | |
| } | |
| static irqreturn_t vc4_hvs_irq_handler(int irq, void *data) | |
| { | |
| struct drm_device *dev = data; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| irqreturn_t irqret = IRQ_NONE; | |
| int channel; | |
| u32 control; | |
| u32 status; | |
| u32 dspeislur; | |
| /* | |
| * NOTE: We don't need to protect the register access using | |
| * drm_dev_enter() there because the interrupt handler lifetime | |
| * is tied to the device itself, and not to the DRM device. | |
| * | |
| * So when the device will be gone, one of the first thing we | |
| * will be doing will be to unregister the interrupt handler, | |
| * and then unregister the DRM device. drm_dev_enter() would | |
| * thus always succeed if we are here. | |
| */ | |
| status = HVS_READ(SCALER_DISPSTAT); | |
| control = HVS_READ(SCALER_DISPCTRL); | |
| for (channel = 0; channel < SCALER_CHANNELS_COUNT; channel++) { | |
| dspeislur = vc4->is_vc5 ? SCALER5_DISPCTRL_DSPEISLUR(channel) : | |
| SCALER_DISPCTRL_DSPEISLUR(channel); | |
| /* Interrupt masking is not always honored, so check it here. */ | |
| if (status & SCALER_DISPSTAT_EUFLOW(channel) && | |
| control & dspeislur) { | |
| vc4_hvs_mask_underrun(hvs, channel); | |
| vc4_hvs_report_underrun(dev); | |
| irqret = IRQ_HANDLED; | |
| } | |
| } | |
| /* Clear every per-channel interrupt flag. */ | |
| HVS_WRITE(SCALER_DISPSTAT, SCALER_DISPSTAT_IRQMASK(0) | | |
| SCALER_DISPSTAT_IRQMASK(1) | | |
| SCALER_DISPSTAT_IRQMASK(2)); | |
| return irqret; | |
| } | |
| int vc4_hvs_debugfs_init(struct drm_minor *minor) | |
| { | |
| struct drm_device *drm = minor->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(drm); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| if (!vc4->hvs) | |
| return -ENODEV; | |
| if (!vc4->is_vc5) | |
| debugfs_create_bool("hvs_load_tracker", S_IRUGO | S_IWUSR, | |
| minor->debugfs_root, | |
| &vc4->load_tracker_enabled); | |
| drm_debugfs_add_file(drm, "hvs_dlists", vc4_hvs_debugfs_dlist, NULL); | |
| drm_debugfs_add_file(drm, "hvs_underrun", vc4_hvs_debugfs_underrun, NULL); | |
| vc4_debugfs_add_regset32(drm, "hvs_regs", &hvs->regset); | |
| return 0; | |
| } | |
| struct vc4_hvs *__vc4_hvs_alloc(struct vc4_dev *vc4, struct platform_device *pdev) | |
| { | |
| struct drm_device *drm = &vc4->base; | |
| struct vc4_hvs *hvs; | |
| hvs = drmm_kzalloc(drm, sizeof(*hvs), GFP_KERNEL); | |
| if (!hvs) | |
| return ERR_PTR(-ENOMEM); | |
| hvs->vc4 = vc4; | |
| hvs->pdev = pdev; | |
| spin_lock_init(&hvs->mm_lock); | |
| /* Set up the HVS display list memory manager. We never | |
| * overwrite the setup from the bootloader (just 128b out of | |
| * our 16K), since we don't want to scramble the screen when | |
| * transitioning from the firmware's boot setup to runtime. | |
| */ | |
| drm_mm_init(&hvs->dlist_mm, | |
| HVS_BOOTLOADER_DLIST_END, | |
| (SCALER_DLIST_SIZE >> 2) - HVS_BOOTLOADER_DLIST_END); | |
| /* Set up the HVS LBM memory manager. We could have some more | |
| * complicated data structure that allowed reuse of LBM areas | |
| * between planes when they don't overlap on the screen, but | |
| * for now we just allocate globally. | |
| */ | |
| if (!vc4->is_vc5) | |
| /* 48k words of 2x12-bit pixels */ | |
| drm_mm_init(&hvs->lbm_mm, 0, 48 * 1024); | |
| else | |
| /* 60k words of 4x12-bit pixels */ | |
| drm_mm_init(&hvs->lbm_mm, 0, 60 * 1024); | |
| vc4->hvs = hvs; | |
| return hvs; | |
| } | |
| static int vc4_hvs_bind(struct device *dev, struct device *master, void *data) | |
| { | |
| struct platform_device *pdev = to_platform_device(dev); | |
| struct drm_device *drm = dev_get_drvdata(master); | |
| struct vc4_dev *vc4 = to_vc4_dev(drm); | |
| struct vc4_hvs *hvs = NULL; | |
| int ret; | |
| u32 dispctrl; | |
| u32 reg, top; | |
| hvs = __vc4_hvs_alloc(vc4, NULL); | |
| if (IS_ERR(hvs)) | |
| return PTR_ERR(hvs); | |
| hvs->regs = vc4_ioremap_regs(pdev, 0); | |
| if (IS_ERR(hvs->regs)) | |
| return PTR_ERR(hvs->regs); | |
| hvs->regset.base = hvs->regs; | |
| hvs->regset.regs = hvs_regs; | |
| hvs->regset.nregs = ARRAY_SIZE(hvs_regs); | |
| if (vc4->is_vc5) { | |
| struct rpi_firmware *firmware; | |
| struct device_node *node; | |
| unsigned int max_rate; | |
| node = rpi_firmware_find_node(); | |
| if (!node) | |
| return -EINVAL; | |
| firmware = rpi_firmware_get(node); | |
| of_node_put(node); | |
| if (!firmware) | |
| return -EPROBE_DEFER; | |
| hvs->core_clk = devm_clk_get(&pdev->dev, NULL); | |
| if (IS_ERR(hvs->core_clk)) { | |
| dev_err(&pdev->dev, "Couldn't get core clock\n"); | |
| return PTR_ERR(hvs->core_clk); | |
| } | |
| max_rate = rpi_firmware_clk_get_max_rate(firmware, | |
| RPI_FIRMWARE_CORE_CLK_ID); | |
| rpi_firmware_put(firmware); | |
| if (max_rate >= 550000000) | |
| hvs->vc5_hdmi_enable_hdmi_20 = true; | |
| if (max_rate >= 600000000) | |
| hvs->vc5_hdmi_enable_4096by2160 = true; | |
| hvs->max_core_rate = max_rate; | |
| ret = clk_prepare_enable(hvs->core_clk); | |
| if (ret) { | |
| dev_err(&pdev->dev, "Couldn't enable the core clock\n"); | |
| return ret; | |
| } | |
| } | |
| if (!vc4->is_vc5) | |
| hvs->dlist = hvs->regs + SCALER_DLIST_START; | |
| else | |
| hvs->dlist = hvs->regs + SCALER5_DLIST_START; | |
| /* Upload filter kernels. We only have the one for now, so we | |
| * keep it around for the lifetime of the driver. | |
| */ | |
| ret = vc4_hvs_upload_linear_kernel(hvs, | |
| &hvs->mitchell_netravali_filter, | |
| mitchell_netravali_1_3_1_3_kernel); | |
| if (ret) | |
| return ret; | |
| reg = HVS_READ(SCALER_DISPECTRL); | |
| reg &= ~SCALER_DISPECTRL_DSP2_MUX_MASK; | |
| HVS_WRITE(SCALER_DISPECTRL, | |
| reg | VC4_SET_FIELD(0, SCALER_DISPECTRL_DSP2_MUX)); | |
| reg = HVS_READ(SCALER_DISPCTRL); | |
| reg &= ~SCALER_DISPCTRL_DSP3_MUX_MASK; | |
| HVS_WRITE(SCALER_DISPCTRL, | |
| reg | VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX)); | |
| reg = HVS_READ(SCALER_DISPEOLN); | |
| reg &= ~SCALER_DISPEOLN_DSP4_MUX_MASK; | |
| HVS_WRITE(SCALER_DISPEOLN, | |
| reg | VC4_SET_FIELD(3, SCALER_DISPEOLN_DSP4_MUX)); | |
| reg = HVS_READ(SCALER_DISPDITHER); | |
| reg &= ~SCALER_DISPDITHER_DSP5_MUX_MASK; | |
| HVS_WRITE(SCALER_DISPDITHER, | |
| reg | VC4_SET_FIELD(3, SCALER_DISPDITHER_DSP5_MUX)); | |
| dispctrl = HVS_READ(SCALER_DISPCTRL); | |
| dispctrl |= SCALER_DISPCTRL_ENABLE; | |
| dispctrl |= SCALER_DISPCTRL_DISPEIRQ(0) | | |
| SCALER_DISPCTRL_DISPEIRQ(1) | | |
| SCALER_DISPCTRL_DISPEIRQ(2); | |
| if (!vc4->is_vc5) | |
| dispctrl &= ~(SCALER_DISPCTRL_DMAEIRQ | | |
| SCALER_DISPCTRL_SLVWREIRQ | | |
| SCALER_DISPCTRL_SLVRDEIRQ | | |
| SCALER_DISPCTRL_DSPEIEOF(0) | | |
| SCALER_DISPCTRL_DSPEIEOF(1) | | |
| SCALER_DISPCTRL_DSPEIEOF(2) | | |
| SCALER_DISPCTRL_DSPEIEOLN(0) | | |
| SCALER_DISPCTRL_DSPEIEOLN(1) | | |
| SCALER_DISPCTRL_DSPEIEOLN(2) | | |
| SCALER_DISPCTRL_DSPEISLUR(0) | | |
| SCALER_DISPCTRL_DSPEISLUR(1) | | |
| SCALER_DISPCTRL_DSPEISLUR(2) | | |
| SCALER_DISPCTRL_SCLEIRQ); | |
| else | |
| dispctrl &= ~(SCALER_DISPCTRL_DMAEIRQ | | |
| SCALER5_DISPCTRL_SLVEIRQ | | |
| SCALER5_DISPCTRL_DSPEIEOF(0) | | |
| SCALER5_DISPCTRL_DSPEIEOF(1) | | |
| SCALER5_DISPCTRL_DSPEIEOF(2) | | |
| SCALER5_DISPCTRL_DSPEIEOLN(0) | | |
| SCALER5_DISPCTRL_DSPEIEOLN(1) | | |
| SCALER5_DISPCTRL_DSPEIEOLN(2) | | |
| SCALER5_DISPCTRL_DSPEISLUR(0) | | |
| SCALER5_DISPCTRL_DSPEISLUR(1) | | |
| SCALER5_DISPCTRL_DSPEISLUR(2) | | |
| SCALER_DISPCTRL_SCLEIRQ); | |
| /* Set AXI panic mode. | |
| * VC4 panics when < 2 lines in FIFO. | |
| * VC5 panics when less than 1 line in the FIFO. | |
| */ | |
| dispctrl &= ~(SCALER_DISPCTRL_PANIC0_MASK | | |
| SCALER_DISPCTRL_PANIC1_MASK | | |
| SCALER_DISPCTRL_PANIC2_MASK); | |
| dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC0); | |
| dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC1); | |
| dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC2); | |
| HVS_WRITE(SCALER_DISPCTRL, dispctrl); | |
| /* Recompute Composite Output Buffer (COB) allocations for the displays | |
| */ | |
| if (!vc4->is_vc5) { | |
| /* The COB is 20736 pixels, or just over 10 lines at 2048 wide. | |
| * The bottom 2048 pixels are full 32bpp RGBA (intended for the | |
| * TXP composing RGBA to memory), whilst the remainder are only | |
| * 24bpp RGB. | |
| * | |
| * Assign 3 lines to channels 1 & 2, and just over 4 lines to | |
| * channel 0. | |
| */ | |
| #define VC4_COB_SIZE 20736 | |
| #define VC4_COB_LINE_WIDTH 2048 | |
| #define VC4_COB_NUM_LINES 3 | |
| reg = 0; | |
| top = VC4_COB_LINE_WIDTH * VC4_COB_NUM_LINES; | |
| reg |= (top - 1) << 16; | |
| HVS_WRITE(SCALER_DISPBASE2, reg); | |
| reg = top; | |
| top += VC4_COB_LINE_WIDTH * VC4_COB_NUM_LINES; | |
| reg |= (top - 1) << 16; | |
| HVS_WRITE(SCALER_DISPBASE1, reg); | |
| reg = top; | |
| top = VC4_COB_SIZE; | |
| reg |= (top - 1) << 16; | |
| HVS_WRITE(SCALER_DISPBASE0, reg); | |
| } else { | |
| /* The COB is 44416 pixels, or 10.8 lines at 4096 wide. | |
| * The bottom 4096 pixels are full RGBA (intended for the TXP | |
| * composing RGBA to memory), whilst the remainder are only | |
| * RGB. Addressing is always pixel wide. | |
| * | |
| * Assign 3 lines of 4096 to channels 1 & 2, and just over 4 | |
| * lines. to channel 0. | |
| */ | |
| #define VC5_COB_SIZE 44416 | |
| #define VC5_COB_LINE_WIDTH 4096 | |
| #define VC5_COB_NUM_LINES 3 | |
| reg = 0; | |
| top = VC5_COB_LINE_WIDTH * VC5_COB_NUM_LINES; | |
| reg |= top << 16; | |
| HVS_WRITE(SCALER_DISPBASE2, reg); | |
| top += 16; | |
| reg = top; | |
| top += VC5_COB_LINE_WIDTH * VC5_COB_NUM_LINES; | |
| reg |= top << 16; | |
| HVS_WRITE(SCALER_DISPBASE1, reg); | |
| top += 16; | |
| reg = top; | |
| top = VC5_COB_SIZE; | |
| reg |= top << 16; | |
| HVS_WRITE(SCALER_DISPBASE0, reg); | |
| } | |
| ret = devm_request_irq(dev, platform_get_irq(pdev, 0), | |
| vc4_hvs_irq_handler, 0, "vc4 hvs", drm); | |
| if (ret) | |
| return ret; | |
| return 0; | |
| } | |
| static void vc4_hvs_unbind(struct device *dev, struct device *master, | |
| void *data) | |
| { | |
| struct drm_device *drm = dev_get_drvdata(master); | |
| struct vc4_dev *vc4 = to_vc4_dev(drm); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| struct drm_mm_node *node, *next; | |
| if (drm_mm_node_allocated(&vc4->hvs->mitchell_netravali_filter)) | |
| drm_mm_remove_node(&vc4->hvs->mitchell_netravali_filter); | |
| drm_mm_for_each_node_safe(node, next, &vc4->hvs->dlist_mm) | |
| drm_mm_remove_node(node); | |
| drm_mm_takedown(&vc4->hvs->dlist_mm); | |
| drm_mm_for_each_node_safe(node, next, &vc4->hvs->lbm_mm) | |
| drm_mm_remove_node(node); | |
| drm_mm_takedown(&vc4->hvs->lbm_mm); | |
| clk_disable_unprepare(hvs->core_clk); | |
| vc4->hvs = NULL; | |
| } | |
| static const struct component_ops vc4_hvs_ops = { | |
| .bind = vc4_hvs_bind, | |
| .unbind = vc4_hvs_unbind, | |
| }; | |
| static int vc4_hvs_dev_probe(struct platform_device *pdev) | |
| { | |
| return component_add(&pdev->dev, &vc4_hvs_ops); | |
| } | |
| static void vc4_hvs_dev_remove(struct platform_device *pdev) | |
| { | |
| component_del(&pdev->dev, &vc4_hvs_ops); | |
| } | |
| static const struct of_device_id vc4_hvs_dt_match[] = { | |
| { .compatible = "brcm,bcm2711-hvs" }, | |
| { .compatible = "brcm,bcm2835-hvs" }, | |
| {} | |
| }; | |
| struct platform_driver vc4_hvs_driver = { | |
| .probe = vc4_hvs_dev_probe, | |
| .remove_new = vc4_hvs_dev_remove, | |
| .driver = { | |
| .name = "vc4_hvs", | |
| .of_match_table = vc4_hvs_dt_match, | |
| }, | |
| }; |