| // SPDX-License-Identifier: GPL-2.0 | |
| // Copyright (c) 2017-2018, The Linux foundation. All rights reserved. | |
| /* Disable MMIO tracing to prevent excessive logging of unwanted MMIO traces */ | |
| #define __DISABLE_TRACE_MMIO__ | |
| #include <linux/clk.h> | |
| #include <linux/console.h> | |
| #include <linux/io.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/irq.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/pm_opp.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/pm_wakeirq.h> | |
| #include <linux/soc/qcom/geni-se.h> | |
| #include <linux/serial.h> | |
| #include <linux/serial_core.h> | |
| #include <linux/slab.h> | |
| #include <linux/tty.h> | |
| #include <linux/tty_flip.h> | |
| #include <dt-bindings/interconnect/qcom,icc.h> | |
| /* UART specific GENI registers */ | |
| #define SE_UART_LOOPBACK_CFG 0x22c | |
| #define SE_UART_IO_MACRO_CTRL 0x240 | |
| #define SE_UART_TX_TRANS_CFG 0x25c | |
| #define SE_UART_TX_WORD_LEN 0x268 | |
| #define SE_UART_TX_STOP_BIT_LEN 0x26c | |
| #define SE_UART_TX_TRANS_LEN 0x270 | |
| #define SE_UART_RX_TRANS_CFG 0x280 | |
| #define SE_UART_RX_WORD_LEN 0x28c | |
| #define SE_UART_RX_STALE_CNT 0x294 | |
| #define SE_UART_TX_PARITY_CFG 0x2a4 | |
| #define SE_UART_RX_PARITY_CFG 0x2a8 | |
| #define SE_UART_MANUAL_RFR 0x2ac | |
| /* SE_UART_TRANS_CFG */ | |
| #define UART_TX_PAR_EN BIT(0) | |
| #define UART_CTS_MASK BIT(1) | |
| /* SE_UART_TX_STOP_BIT_LEN */ | |
| #define TX_STOP_BIT_LEN_1 0 | |
| #define TX_STOP_BIT_LEN_2 2 | |
| /* SE_UART_RX_TRANS_CFG */ | |
| #define UART_RX_PAR_EN BIT(3) | |
| /* SE_UART_RX_WORD_LEN */ | |
| #define RX_WORD_LEN_MASK GENMASK(9, 0) | |
| /* SE_UART_RX_STALE_CNT */ | |
| #define RX_STALE_CNT GENMASK(23, 0) | |
| /* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */ | |
| #define PAR_CALC_EN BIT(0) | |
| #define PAR_EVEN 0x00 | |
| #define PAR_ODD 0x01 | |
| #define PAR_SPACE 0x10 | |
| /* SE_UART_MANUAL_RFR register fields */ | |
| #define UART_MANUAL_RFR_EN BIT(31) | |
| #define UART_RFR_NOT_READY BIT(1) | |
| #define UART_RFR_READY BIT(0) | |
| /* UART M_CMD OP codes */ | |
| #define UART_START_TX 0x1 | |
| /* UART S_CMD OP codes */ | |
| #define UART_START_READ 0x1 | |
| #define UART_PARAM 0x1 | |
| #define UART_PARAM_RFR_OPEN BIT(7) | |
| #define UART_OVERSAMPLING 32 | |
| #define STALE_TIMEOUT 16 | |
| #define DEFAULT_BITS_PER_CHAR 10 | |
| #define GENI_UART_CONS_PORTS 1 | |
| #define GENI_UART_PORTS 3 | |
| #define DEF_FIFO_DEPTH_WORDS 16 | |
| #define DEF_TX_WM 2 | |
| #define DEF_FIFO_WIDTH_BITS 32 | |
| #define UART_RX_WM 2 | |
| /* SE_UART_LOOPBACK_CFG */ | |
| #define RX_TX_SORTED BIT(0) | |
| #define CTS_RTS_SORTED BIT(1) | |
| #define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED) | |
| /* UART pin swap value */ | |
| #define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0) | |
| #define IO_MACRO_IO0_SEL 0x3 | |
| #define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4) | |
| #define IO_MACRO_IO2_IO3_SWAP 0x4640 | |
| /* We always configure 4 bytes per FIFO word */ | |
| #define BYTES_PER_FIFO_WORD 4U | |
| #define DMA_RX_BUF_SIZE 2048 | |
| struct qcom_geni_device_data { | |
| bool console; | |
| enum geni_se_xfer_mode mode; | |
| }; | |
| struct qcom_geni_private_data { | |
| /* NOTE: earlycon port will have NULL here */ | |
| struct uart_driver *drv; | |
| u32 poll_cached_bytes; | |
| unsigned int poll_cached_bytes_cnt; | |
| u32 write_cached_bytes; | |
| unsigned int write_cached_bytes_cnt; | |
| }; | |
| struct qcom_geni_serial_port { | |
| struct uart_port uport; | |
| struct geni_se se; | |
| const char *name; | |
| u32 tx_fifo_depth; | |
| u32 tx_fifo_width; | |
| u32 rx_fifo_depth; | |
| dma_addr_t tx_dma_addr; | |
| dma_addr_t rx_dma_addr; | |
| bool setup; | |
| unsigned long poll_timeout_us; | |
| unsigned long clk_rate; | |
| void *rx_buf; | |
| u32 loopback; | |
| bool brk; | |
| unsigned int tx_remaining; | |
| unsigned int tx_queued; | |
| int wakeup_irq; | |
| bool rx_tx_swap; | |
| bool cts_rts_swap; | |
| struct qcom_geni_private_data private_data; | |
| const struct qcom_geni_device_data *dev_data; | |
| }; | |
| static const struct uart_ops qcom_geni_console_pops; | |
| static const struct uart_ops qcom_geni_uart_pops; | |
| static struct uart_driver qcom_geni_console_driver; | |
| static struct uart_driver qcom_geni_uart_driver; | |
| static void __qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport); | |
| static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport); | |
| static inline struct qcom_geni_serial_port *to_dev_port(struct uart_port *uport) | |
| { | |
| return container_of(uport, struct qcom_geni_serial_port, uport); | |
| } | |
| static struct qcom_geni_serial_port qcom_geni_uart_ports[GENI_UART_PORTS] = { | |
| [0] = { | |
| .uport = { | |
| .iotype = UPIO_MEM, | |
| .ops = &qcom_geni_uart_pops, | |
| .flags = UPF_BOOT_AUTOCONF, | |
| .line = 0, | |
| }, | |
| }, | |
| [1] = { | |
| .uport = { | |
| .iotype = UPIO_MEM, | |
| .ops = &qcom_geni_uart_pops, | |
| .flags = UPF_BOOT_AUTOCONF, | |
| .line = 1, | |
| }, | |
| }, | |
| [2] = { | |
| .uport = { | |
| .iotype = UPIO_MEM, | |
| .ops = &qcom_geni_uart_pops, | |
| .flags = UPF_BOOT_AUTOCONF, | |
| .line = 2, | |
| }, | |
| }, | |
| }; | |
| static struct qcom_geni_serial_port qcom_geni_console_port = { | |
| .uport = { | |
| .iotype = UPIO_MEM, | |
| .ops = &qcom_geni_console_pops, | |
| .flags = UPF_BOOT_AUTOCONF, | |
| .line = 0, | |
| }, | |
| }; | |
| static int qcom_geni_serial_request_port(struct uart_port *uport) | |
| { | |
| struct platform_device *pdev = to_platform_device(uport->dev); | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| uport->membase = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(uport->membase)) | |
| return PTR_ERR(uport->membase); | |
| port->se.base = uport->membase; | |
| return 0; | |
| } | |
| static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags) | |
| { | |
| if (cfg_flags & UART_CONFIG_TYPE) { | |
| uport->type = PORT_MSM; | |
| qcom_geni_serial_request_port(uport); | |
| } | |
| } | |
| static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) | |
| { | |
| unsigned int mctrl = TIOCM_DSR | TIOCM_CAR; | |
| u32 geni_ios; | |
| if (uart_console(uport)) { | |
| mctrl |= TIOCM_CTS; | |
| } else { | |
| geni_ios = readl(uport->membase + SE_GENI_IOS); | |
| if (!(geni_ios & IO2_DATA_IN)) | |
| mctrl |= TIOCM_CTS; | |
| } | |
| return mctrl; | |
| } | |
| static void qcom_geni_serial_set_mctrl(struct uart_port *uport, | |
| unsigned int mctrl) | |
| { | |
| u32 uart_manual_rfr = 0; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (uart_console(uport)) | |
| return; | |
| if (mctrl & TIOCM_LOOP) | |
| port->loopback = RX_TX_CTS_RTS_SORTED; | |
| if (!(mctrl & TIOCM_RTS) && !uport->suspended) | |
| uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; | |
| writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); | |
| } | |
| static const char *qcom_geni_serial_get_type(struct uart_port *uport) | |
| { | |
| return "MSM"; | |
| } | |
| static struct qcom_geni_serial_port *get_port_from_line(int line, bool console) | |
| { | |
| struct qcom_geni_serial_port *port; | |
| int nr_ports = console ? GENI_UART_CONS_PORTS : GENI_UART_PORTS; | |
| if (line < 0 || line >= nr_ports) | |
| return ERR_PTR(-ENXIO); | |
| port = console ? &qcom_geni_console_port : &qcom_geni_uart_ports[line]; | |
| return port; | |
| } | |
| static bool qcom_geni_serial_main_active(struct uart_port *uport) | |
| { | |
| return readl(uport->membase + SE_GENI_STATUS) & M_GENI_CMD_ACTIVE; | |
| } | |
| static bool qcom_geni_serial_secondary_active(struct uart_port *uport) | |
| { | |
| return readl(uport->membase + SE_GENI_STATUS) & S_GENI_CMD_ACTIVE; | |
| } | |
| static bool qcom_geni_serial_poll_bitfield(struct uart_port *uport, | |
| unsigned int offset, u32 field, u32 val) | |
| { | |
| u32 reg; | |
| struct qcom_geni_serial_port *port; | |
| unsigned long timeout_us = 20000; | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| if (private_data->drv) { | |
| port = to_dev_port(uport); | |
| if (port->poll_timeout_us) | |
| timeout_us = port->poll_timeout_us; | |
| } | |
| /* | |
| * Use custom implementation instead of readl_poll_atomic since ktimer | |
| * is not ready at the time of early console. | |
| */ | |
| timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; | |
| while (timeout_us) { | |
| reg = readl(uport->membase + offset); | |
| if ((reg & field) == val) | |
| return true; | |
| udelay(10); | |
| timeout_us -= 10; | |
| } | |
| return false; | |
| } | |
| static bool qcom_geni_serial_poll_bit(struct uart_port *uport, | |
| unsigned int offset, u32 field, bool set) | |
| { | |
| return qcom_geni_serial_poll_bitfield(uport, offset, field, set ? field : 0); | |
| } | |
| static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) | |
| { | |
| u32 m_cmd; | |
| writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); | |
| m_cmd = UART_START_TX << M_OPCODE_SHFT; | |
| writel(m_cmd, uport->membase + SE_GENI_M_CMD0); | |
| } | |
| static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) | |
| { | |
| int done; | |
| done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_DONE_EN, true); | |
| if (!done) { | |
| writel(M_GENI_CMD_ABORT, uport->membase + | |
| SE_GENI_M_CMD_CTRL_REG); | |
| qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_ABORT_EN, true); | |
| writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| } | |
| } | |
| static void qcom_geni_serial_abort_rx(struct uart_port *uport) | |
| { | |
| u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN; | |
| writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); | |
| qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, | |
| S_GENI_CMD_ABORT, false); | |
| writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); | |
| writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); | |
| } | |
| #ifdef CONFIG_CONSOLE_POLL | |
| static int qcom_geni_serial_get_char(struct uart_port *uport) | |
| { | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| u32 status; | |
| u32 word_cnt; | |
| int ret; | |
| if (!private_data->poll_cached_bytes_cnt) { | |
| status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); | |
| writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); | |
| writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR); | |
| status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); | |
| word_cnt = status & RX_FIFO_WC_MSK; | |
| if (!word_cnt) | |
| return NO_POLL_CHAR; | |
| if (word_cnt == 1 && (status & RX_LAST)) | |
| /* | |
| * NOTE: If RX_LAST_BYTE_VALID is 0 it needs to be | |
| * treated as if it was BYTES_PER_FIFO_WORD. | |
| */ | |
| private_data->poll_cached_bytes_cnt = | |
| (status & RX_LAST_BYTE_VALID_MSK) >> | |
| RX_LAST_BYTE_VALID_SHFT; | |
| if (private_data->poll_cached_bytes_cnt == 0) | |
| private_data->poll_cached_bytes_cnt = BYTES_PER_FIFO_WORD; | |
| private_data->poll_cached_bytes = | |
| readl(uport->membase + SE_GENI_RX_FIFOn); | |
| } | |
| private_data->poll_cached_bytes_cnt--; | |
| ret = private_data->poll_cached_bytes & 0xff; | |
| private_data->poll_cached_bytes >>= 8; | |
| return ret; | |
| } | |
| static void qcom_geni_serial_poll_put_char(struct uart_port *uport, | |
| unsigned char c) | |
| { | |
| if (qcom_geni_serial_main_active(uport)) { | |
| qcom_geni_serial_poll_tx_done(uport); | |
| __qcom_geni_serial_cancel_tx_cmd(uport); | |
| } | |
| writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| qcom_geni_serial_setup_tx(uport, 1); | |
| writel(c, uport->membase + SE_GENI_TX_FIFOn); | |
| qcom_geni_serial_poll_tx_done(uport); | |
| } | |
| #endif | |
| #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE | |
| static void qcom_geni_serial_drain_fifo(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| qcom_geni_serial_poll_bitfield(uport, SE_GENI_M_GP_LENGTH, GP_LENGTH, | |
| port->tx_queued); | |
| } | |
| static void qcom_geni_serial_wr_char(struct uart_port *uport, unsigned char ch) | |
| { | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| private_data->write_cached_bytes = | |
| (private_data->write_cached_bytes >> 8) | (ch << 24); | |
| private_data->write_cached_bytes_cnt++; | |
| if (private_data->write_cached_bytes_cnt == BYTES_PER_FIFO_WORD) { | |
| writel(private_data->write_cached_bytes, | |
| uport->membase + SE_GENI_TX_FIFOn); | |
| private_data->write_cached_bytes_cnt = 0; | |
| } | |
| } | |
| static void | |
| __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, | |
| unsigned int count) | |
| { | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| int i; | |
| u32 bytes_to_send = count; | |
| for (i = 0; i < count; i++) { | |
| /* | |
| * uart_console_write() adds a carriage return for each newline. | |
| * Account for additional bytes to be written. | |
| */ | |
| if (s[i] == '\n') | |
| bytes_to_send++; | |
| } | |
| writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); | |
| writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| qcom_geni_serial_setup_tx(uport, bytes_to_send); | |
| for (i = 0; i < count; ) { | |
| size_t chars_to_write = 0; | |
| size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM; | |
| /* | |
| * If the WM bit never set, then the Tx state machine is not | |
| * in a valid state, so break, cancel/abort any existing | |
| * command. Unfortunately the current data being written is | |
| * lost. | |
| */ | |
| if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_TX_FIFO_WATERMARK_EN, true)) | |
| break; | |
| chars_to_write = min_t(size_t, count - i, avail / 2); | |
| uart_console_write(uport, s + i, chars_to_write, | |
| qcom_geni_serial_wr_char); | |
| writel(M_TX_FIFO_WATERMARK_EN, uport->membase + | |
| SE_GENI_M_IRQ_CLEAR); | |
| i += chars_to_write; | |
| } | |
| if (private_data->write_cached_bytes_cnt) { | |
| private_data->write_cached_bytes >>= BITS_PER_BYTE * | |
| (BYTES_PER_FIFO_WORD - private_data->write_cached_bytes_cnt); | |
| writel(private_data->write_cached_bytes, | |
| uport->membase + SE_GENI_TX_FIFOn); | |
| private_data->write_cached_bytes_cnt = 0; | |
| } | |
| qcom_geni_serial_poll_tx_done(uport); | |
| } | |
| static void qcom_geni_serial_console_write(struct console *co, const char *s, | |
| unsigned int count) | |
| { | |
| struct uart_port *uport; | |
| struct qcom_geni_serial_port *port; | |
| u32 m_irq_en, s_irq_en; | |
| bool locked = true; | |
| unsigned long flags; | |
| WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS); | |
| port = get_port_from_line(co->index, true); | |
| if (IS_ERR(port)) | |
| return; | |
| uport = &port->uport; | |
| if (oops_in_progress) | |
| locked = uart_port_trylock_irqsave(uport, &flags); | |
| else | |
| uart_port_lock_irqsave(uport, &flags); | |
| m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| s_irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); | |
| writel(0, uport->membase + SE_GENI_M_IRQ_EN); | |
| writel(0, uport->membase + SE_GENI_S_IRQ_EN); | |
| if (qcom_geni_serial_main_active(uport)) { | |
| /* Wait for completion or drain FIFO */ | |
| if (!locked || port->tx_remaining == 0) | |
| qcom_geni_serial_poll_tx_done(uport); | |
| else | |
| qcom_geni_serial_drain_fifo(uport); | |
| qcom_geni_serial_cancel_tx_cmd(uport); | |
| } | |
| __qcom_geni_serial_console_write(uport, s, count); | |
| writel(m_irq_en, uport->membase + SE_GENI_M_IRQ_EN); | |
| writel(s_irq_en, uport->membase + SE_GENI_S_IRQ_EN); | |
| if (locked) | |
| uart_port_unlock_irqrestore(uport, flags); | |
| } | |
| static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) | |
| { | |
| u32 i; | |
| unsigned char buf[sizeof(u32)]; | |
| struct tty_port *tport; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| tport = &uport->state->port; | |
| for (i = 0; i < bytes; ) { | |
| int c; | |
| int chunk = min_t(int, bytes - i, BYTES_PER_FIFO_WORD); | |
| ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1); | |
| i += chunk; | |
| if (drop) | |
| continue; | |
| for (c = 0; c < chunk; c++) { | |
| int sysrq; | |
| uport->icount.rx++; | |
| if (port->brk && buf[c] == 0) { | |
| port->brk = false; | |
| if (uart_handle_break(uport)) | |
| continue; | |
| } | |
| sysrq = uart_prepare_sysrq_char(uport, buf[c]); | |
| if (!sysrq) | |
| tty_insert_flip_char(tport, buf[c], TTY_NORMAL); | |
| } | |
| } | |
| if (!drop) | |
| tty_flip_buffer_push(tport); | |
| } | |
| #else | |
| static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) | |
| { | |
| } | |
| #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ | |
| static void handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| struct tty_port *tport = &uport->state->port; | |
| int ret; | |
| ret = tty_insert_flip_string(tport, port->rx_buf, bytes); | |
| if (ret != bytes) { | |
| dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n", | |
| __func__, ret, bytes); | |
| WARN_ON_ONCE(1); | |
| } | |
| uport->icount.rx += ret; | |
| tty_flip_buffer_push(tport); | |
| } | |
| static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport) | |
| { | |
| return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS); | |
| } | |
| static void qcom_geni_serial_stop_tx_dma(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| bool done; | |
| if (!qcom_geni_serial_main_active(uport)) | |
| return; | |
| if (port->tx_dma_addr) { | |
| geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr, | |
| port->tx_remaining); | |
| port->tx_dma_addr = 0; | |
| port->tx_remaining = 0; | |
| } | |
| geni_se_cancel_m_cmd(&port->se); | |
| done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_CANCEL_EN, true); | |
| if (!done) { | |
| geni_se_abort_m_cmd(&port->se); | |
| done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_ABORT_EN, true); | |
| if (!done) | |
| dev_err_ratelimited(uport->dev, "M_CMD_ABORT_EN not set"); | |
| writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| } | |
| writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| } | |
| static void qcom_geni_serial_start_tx_dma(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| struct tty_port *tport = &uport->state->port; | |
| unsigned int xmit_size; | |
| u8 *tail; | |
| int ret; | |
| if (port->tx_dma_addr) | |
| return; | |
| if (kfifo_is_empty(&tport->xmit_fifo)) | |
| return; | |
| xmit_size = kfifo_out_linear_ptr(&tport->xmit_fifo, &tail, | |
| UART_XMIT_SIZE); | |
| qcom_geni_serial_setup_tx(uport, xmit_size); | |
| ret = geni_se_tx_dma_prep(&port->se, tail, xmit_size, | |
| &port->tx_dma_addr); | |
| if (ret) { | |
| dev_err(uport->dev, "unable to start TX SE DMA: %d\n", ret); | |
| qcom_geni_serial_stop_tx_dma(uport); | |
| return; | |
| } | |
| port->tx_remaining = xmit_size; | |
| } | |
| static void qcom_geni_serial_start_tx_fifo(struct uart_port *uport) | |
| { | |
| unsigned char c; | |
| u32 irq_en; | |
| /* | |
| * Start a new transfer in case the previous command was cancelled and | |
| * left data in the FIFO which may prevent the watermark interrupt | |
| * from triggering. Note that the stale data is discarded. | |
| */ | |
| if (!qcom_geni_serial_main_active(uport) && | |
| !qcom_geni_serial_tx_empty(uport)) { | |
| if (uart_fifo_out(uport, &c, 1) == 1) { | |
| writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| qcom_geni_serial_setup_tx(uport, 1); | |
| writel(c, uport->membase + SE_GENI_TX_FIFOn); | |
| } | |
| } | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; | |
| writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); | |
| writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); | |
| } | |
| static void qcom_geni_serial_stop_tx_fifo(struct uart_port *uport) | |
| { | |
| u32 irq_en; | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN); | |
| writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG); | |
| writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); | |
| } | |
| static void __qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| geni_se_cancel_m_cmd(&port->se); | |
| if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_CANCEL_EN, true)) { | |
| geni_se_abort_m_cmd(&port->se); | |
| qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, | |
| M_CMD_ABORT_EN, true); | |
| writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| } | |
| writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| } | |
| static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (!qcom_geni_serial_main_active(uport)) | |
| return; | |
| __qcom_geni_serial_cancel_tx_cmd(uport); | |
| port->tx_remaining = 0; | |
| port->tx_queued = 0; | |
| } | |
| static void qcom_geni_serial_handle_rx_fifo(struct uart_port *uport, bool drop) | |
| { | |
| u32 status; | |
| u32 word_cnt; | |
| u32 last_word_byte_cnt; | |
| u32 last_word_partial; | |
| u32 total_bytes; | |
| status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); | |
| word_cnt = status & RX_FIFO_WC_MSK; | |
| last_word_partial = status & RX_LAST; | |
| last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> | |
| RX_LAST_BYTE_VALID_SHFT; | |
| if (!word_cnt) | |
| return; | |
| total_bytes = BYTES_PER_FIFO_WORD * (word_cnt - 1); | |
| if (last_word_partial && last_word_byte_cnt) | |
| total_bytes += last_word_byte_cnt; | |
| else | |
| total_bytes += BYTES_PER_FIFO_WORD; | |
| handle_rx_console(uport, total_bytes, drop); | |
| } | |
| static void qcom_geni_serial_stop_rx_fifo(struct uart_port *uport) | |
| { | |
| u32 irq_en; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| u32 s_irq_status; | |
| irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); | |
| irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); | |
| writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); | |
| writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); | |
| if (!qcom_geni_serial_secondary_active(uport)) | |
| return; | |
| geni_se_cancel_s_cmd(&port->se); | |
| qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS, | |
| S_CMD_CANCEL_EN, true); | |
| /* | |
| * If timeout occurs secondary engine remains active | |
| * and Abort sequence is executed. | |
| */ | |
| s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); | |
| /* Flush the Rx buffer */ | |
| if (s_irq_status & S_RX_FIFO_LAST_EN) | |
| qcom_geni_serial_handle_rx_fifo(uport, true); | |
| writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); | |
| if (qcom_geni_serial_secondary_active(uport)) | |
| qcom_geni_serial_abort_rx(uport); | |
| } | |
| static void qcom_geni_serial_start_rx_fifo(struct uart_port *uport) | |
| { | |
| u32 irq_en; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (qcom_geni_serial_secondary_active(uport)) | |
| qcom_geni_serial_stop_rx_fifo(uport); | |
| geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); | |
| irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); | |
| irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; | |
| writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; | |
| writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); | |
| } | |
| static void qcom_geni_serial_stop_rx_dma(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (!qcom_geni_serial_secondary_active(uport)) | |
| return; | |
| geni_se_cancel_s_cmd(&port->se); | |
| qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS, | |
| S_CMD_CANCEL_EN, true); | |
| if (qcom_geni_serial_secondary_active(uport)) | |
| qcom_geni_serial_abort_rx(uport); | |
| if (port->rx_dma_addr) { | |
| geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr, | |
| DMA_RX_BUF_SIZE); | |
| port->rx_dma_addr = 0; | |
| } | |
| } | |
| static void qcom_geni_serial_start_rx_dma(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| int ret; | |
| if (qcom_geni_serial_secondary_active(uport)) | |
| qcom_geni_serial_stop_rx_dma(uport); | |
| geni_se_setup_s_cmd(&port->se, UART_START_READ, UART_PARAM_RFR_OPEN); | |
| ret = geni_se_rx_dma_prep(&port->se, port->rx_buf, | |
| DMA_RX_BUF_SIZE, | |
| &port->rx_dma_addr); | |
| if (ret) { | |
| dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret); | |
| qcom_geni_serial_stop_rx_dma(uport); | |
| } | |
| } | |
| static void qcom_geni_serial_handle_rx_dma(struct uart_port *uport, bool drop) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| u32 rx_in; | |
| int ret; | |
| if (!qcom_geni_serial_secondary_active(uport)) | |
| return; | |
| if (!port->rx_dma_addr) | |
| return; | |
| geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr, DMA_RX_BUF_SIZE); | |
| port->rx_dma_addr = 0; | |
| rx_in = readl(uport->membase + SE_DMA_RX_LEN_IN); | |
| if (!rx_in) { | |
| dev_warn(uport->dev, "serial engine reports 0 RX bytes in!\n"); | |
| return; | |
| } | |
| if (!drop) | |
| handle_rx_uart(uport, rx_in, drop); | |
| ret = geni_se_rx_dma_prep(&port->se, port->rx_buf, | |
| DMA_RX_BUF_SIZE, | |
| &port->rx_dma_addr); | |
| if (ret) { | |
| dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret); | |
| qcom_geni_serial_stop_rx_dma(uport); | |
| } | |
| } | |
| static void qcom_geni_serial_start_rx(struct uart_port *uport) | |
| { | |
| uport->ops->start_rx(uport); | |
| } | |
| static void qcom_geni_serial_stop_rx(struct uart_port *uport) | |
| { | |
| uport->ops->stop_rx(uport); | |
| } | |
| static void qcom_geni_serial_stop_tx(struct uart_port *uport) | |
| { | |
| uport->ops->stop_tx(uport); | |
| } | |
| static void qcom_geni_serial_send_chunk_fifo(struct uart_port *uport, | |
| unsigned int chunk) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| unsigned int tx_bytes, remaining = chunk; | |
| u8 buf[BYTES_PER_FIFO_WORD]; | |
| while (remaining) { | |
| memset(buf, 0, sizeof(buf)); | |
| tx_bytes = min(remaining, BYTES_PER_FIFO_WORD); | |
| uart_fifo_out(uport, buf, tx_bytes); | |
| iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1); | |
| remaining -= tx_bytes; | |
| port->tx_remaining -= tx_bytes; | |
| } | |
| } | |
| static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport, | |
| bool done, bool active) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| struct tty_port *tport = &uport->state->port; | |
| size_t avail; | |
| size_t pending; | |
| u32 status; | |
| u32 irq_en; | |
| unsigned int chunk; | |
| status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS); | |
| /* Complete the current tx command before taking newly added data */ | |
| if (active) | |
| pending = port->tx_remaining; | |
| else | |
| pending = kfifo_len(&tport->xmit_fifo); | |
| /* All data has been transmitted or command has been cancelled */ | |
| if (!pending && done) { | |
| qcom_geni_serial_stop_tx_fifo(uport); | |
| goto out_write_wakeup; | |
| } | |
| if (active) | |
| avail = port->tx_fifo_depth - (status & TX_FIFO_WC); | |
| else | |
| avail = port->tx_fifo_depth; | |
| avail *= BYTES_PER_FIFO_WORD; | |
| chunk = min(avail, pending); | |
| if (!chunk) | |
| goto out_write_wakeup; | |
| if (!active) { | |
| qcom_geni_serial_setup_tx(uport, pending); | |
| port->tx_remaining = pending; | |
| port->tx_queued = 0; | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| if (!(irq_en & M_TX_FIFO_WATERMARK_EN)) | |
| writel(irq_en | M_TX_FIFO_WATERMARK_EN, | |
| uport->membase + SE_GENI_M_IRQ_EN); | |
| } | |
| qcom_geni_serial_send_chunk_fifo(uport, chunk); | |
| port->tx_queued += chunk; | |
| /* | |
| * The tx fifo watermark is level triggered and latched. Though we had | |
| * cleared it in qcom_geni_serial_isr it will have already reasserted | |
| * so we must clear it again here after our writes. | |
| */ | |
| writel(M_TX_FIFO_WATERMARK_EN, | |
| uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| out_write_wakeup: | |
| if (!port->tx_remaining) { | |
| irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| if (irq_en & M_TX_FIFO_WATERMARK_EN) | |
| writel(irq_en & ~M_TX_FIFO_WATERMARK_EN, | |
| uport->membase + SE_GENI_M_IRQ_EN); | |
| } | |
| if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) | |
| uart_write_wakeup(uport); | |
| } | |
| static void qcom_geni_serial_handle_tx_dma(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| struct tty_port *tport = &uport->state->port; | |
| uart_xmit_advance(uport, port->tx_remaining); | |
| geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr, port->tx_remaining); | |
| port->tx_dma_addr = 0; | |
| port->tx_remaining = 0; | |
| if (!kfifo_is_empty(&tport->xmit_fifo)) | |
| qcom_geni_serial_start_tx_dma(uport); | |
| if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) | |
| uart_write_wakeup(uport); | |
| } | |
| static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) | |
| { | |
| u32 m_irq_en; | |
| u32 m_irq_status; | |
| u32 s_irq_status; | |
| u32 geni_status; | |
| u32 dma; | |
| u32 dma_tx_status; | |
| u32 dma_rx_status; | |
| struct uart_port *uport = dev; | |
| bool drop_rx = false; | |
| struct tty_port *tport = &uport->state->port; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (uport->suspended) | |
| return IRQ_NONE; | |
| uart_port_lock(uport); | |
| m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); | |
| s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); | |
| dma_tx_status = readl(uport->membase + SE_DMA_TX_IRQ_STAT); | |
| dma_rx_status = readl(uport->membase + SE_DMA_RX_IRQ_STAT); | |
| geni_status = readl(uport->membase + SE_GENI_STATUS); | |
| dma = readl(uport->membase + SE_GENI_DMA_MODE_EN); | |
| m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); | |
| writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); | |
| writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); | |
| writel(dma_tx_status, uport->membase + SE_DMA_TX_IRQ_CLR); | |
| writel(dma_rx_status, uport->membase + SE_DMA_RX_IRQ_CLR); | |
| if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) | |
| goto out_unlock; | |
| if (s_irq_status & S_RX_FIFO_WR_ERR_EN) { | |
| uport->icount.overrun++; | |
| tty_insert_flip_char(tport, 0, TTY_OVERRUN); | |
| } | |
| if (s_irq_status & (S_GP_IRQ_0_EN | S_GP_IRQ_1_EN)) { | |
| if (s_irq_status & S_GP_IRQ_0_EN) | |
| uport->icount.parity++; | |
| drop_rx = true; | |
| } else if (s_irq_status & (S_GP_IRQ_2_EN | S_GP_IRQ_3_EN)) { | |
| uport->icount.brk++; | |
| port->brk = true; | |
| } | |
| if (dma) { | |
| if (dma_tx_status & TX_DMA_DONE) | |
| qcom_geni_serial_handle_tx_dma(uport); | |
| if (dma_rx_status) { | |
| if (dma_rx_status & RX_RESET_DONE) | |
| goto out_unlock; | |
| if (dma_rx_status & RX_DMA_PARITY_ERR) { | |
| uport->icount.parity++; | |
| drop_rx = true; | |
| } | |
| if (dma_rx_status & RX_DMA_BREAK) | |
| uport->icount.brk++; | |
| if (dma_rx_status & (RX_DMA_DONE | RX_EOT)) | |
| qcom_geni_serial_handle_rx_dma(uport, drop_rx); | |
| } | |
| } else { | |
| if (m_irq_status & m_irq_en & | |
| (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN)) | |
| qcom_geni_serial_handle_tx_fifo(uport, | |
| m_irq_status & M_CMD_DONE_EN, | |
| geni_status & M_GENI_CMD_ACTIVE); | |
| if (s_irq_status & (S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN)) | |
| qcom_geni_serial_handle_rx_fifo(uport, drop_rx); | |
| } | |
| out_unlock: | |
| uart_unlock_and_check_sysrq(uport); | |
| return IRQ_HANDLED; | |
| } | |
| static int setup_fifos(struct qcom_geni_serial_port *port) | |
| { | |
| struct uart_port *uport; | |
| u32 old_rx_fifo_depth = port->rx_fifo_depth; | |
| uport = &port->uport; | |
| port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); | |
| port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); | |
| port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); | |
| uport->fifosize = | |
| (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE; | |
| if (port->rx_buf && (old_rx_fifo_depth != port->rx_fifo_depth) && port->rx_fifo_depth) { | |
| /* | |
| * Use krealloc rather than krealloc_array because rx_buf is | |
| * accessed as 1 byte entries as well as 4 byte entries so it's | |
| * not necessarily an array. | |
| */ | |
| port->rx_buf = devm_krealloc(uport->dev, port->rx_buf, | |
| port->rx_fifo_depth * sizeof(u32), | |
| GFP_KERNEL); | |
| if (!port->rx_buf) | |
| return -ENOMEM; | |
| } | |
| return 0; | |
| } | |
| static void qcom_geni_serial_shutdown(struct uart_port *uport) | |
| { | |
| disable_irq(uport->irq); | |
| qcom_geni_serial_stop_tx(uport); | |
| qcom_geni_serial_stop_rx(uport); | |
| qcom_geni_serial_cancel_tx_cmd(uport); | |
| } | |
| static void qcom_geni_serial_flush_buffer(struct uart_port *uport) | |
| { | |
| qcom_geni_serial_cancel_tx_cmd(uport); | |
| } | |
| static int qcom_geni_serial_port_setup(struct uart_port *uport) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; | |
| u32 proto; | |
| u32 pin_swap; | |
| int ret; | |
| proto = geni_se_read_proto(&port->se); | |
| if (proto != GENI_SE_UART) { | |
| dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto); | |
| return -ENXIO; | |
| } | |
| qcom_geni_serial_stop_rx(uport); | |
| ret = setup_fifos(port); | |
| if (ret) | |
| return ret; | |
| writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT); | |
| pin_swap = readl(uport->membase + SE_UART_IO_MACRO_CTRL); | |
| if (port->rx_tx_swap) { | |
| pin_swap &= ~DEFAULT_IO_MACRO_IO2_IO3_MASK; | |
| pin_swap |= IO_MACRO_IO2_IO3_SWAP; | |
| } | |
| if (port->cts_rts_swap) { | |
| pin_swap &= ~DEFAULT_IO_MACRO_IO0_IO1_MASK; | |
| pin_swap |= IO_MACRO_IO0_SEL; | |
| } | |
| /* Configure this register if RX-TX, CTS-RTS pins are swapped */ | |
| if (port->rx_tx_swap || port->cts_rts_swap) | |
| writel(pin_swap, uport->membase + SE_UART_IO_MACRO_CTRL); | |
| /* | |
| * Make an unconditional cancel on the main sequencer to reset | |
| * it else we could end up in data loss scenarios. | |
| */ | |
| if (uart_console(uport)) | |
| qcom_geni_serial_poll_tx_done(uport); | |
| geni_se_config_packing(&port->se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, | |
| false, true, true); | |
| geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2); | |
| geni_se_select_mode(&port->se, port->dev_data->mode); | |
| qcom_geni_serial_start_rx(uport); | |
| port->setup = true; | |
| return 0; | |
| } | |
| static int qcom_geni_serial_startup(struct uart_port *uport) | |
| { | |
| int ret; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| if (!port->setup) { | |
| ret = qcom_geni_serial_port_setup(uport); | |
| if (ret) | |
| return ret; | |
| } | |
| enable_irq(uport->irq); | |
| return 0; | |
| } | |
| static unsigned long find_clk_rate_in_tol(struct clk *clk, unsigned int desired_clk, | |
| unsigned int *clk_div, unsigned int percent_tol) | |
| { | |
| unsigned long freq; | |
| unsigned long div, maxdiv; | |
| u64 mult; | |
| unsigned long offset, abs_tol, achieved; | |
| abs_tol = div_u64((u64)desired_clk * percent_tol, 100); | |
| maxdiv = CLK_DIV_MSK >> CLK_DIV_SHFT; | |
| div = 1; | |
| while (div <= maxdiv) { | |
| mult = (u64)div * desired_clk; | |
| if (mult != (unsigned long)mult) | |
| break; | |
| offset = div * abs_tol; | |
| freq = clk_round_rate(clk, mult - offset); | |
| /* Can only get lower if we're done */ | |
| if (freq < mult - offset) | |
| break; | |
| /* | |
| * Re-calculate div in case rounding skipped rates but we | |
| * ended up at a good one, then check for a match. | |
| */ | |
| div = DIV_ROUND_CLOSEST(freq, desired_clk); | |
| achieved = DIV_ROUND_CLOSEST(freq, div); | |
| if (achieved <= desired_clk + abs_tol && | |
| achieved >= desired_clk - abs_tol) { | |
| *clk_div = div; | |
| return freq; | |
| } | |
| div = DIV_ROUND_UP(freq, desired_clk); | |
| } | |
| return 0; | |
| } | |
| static unsigned long get_clk_div_rate(struct clk *clk, unsigned int baud, | |
| unsigned int sampling_rate, unsigned int *clk_div) | |
| { | |
| unsigned long ser_clk; | |
| unsigned long desired_clk; | |
| desired_clk = baud * sampling_rate; | |
| if (!desired_clk) | |
| return 0; | |
| /* | |
| * try to find a clock rate within 2% tolerance, then within 5% | |
| */ | |
| ser_clk = find_clk_rate_in_tol(clk, desired_clk, clk_div, 2); | |
| if (!ser_clk) | |
| ser_clk = find_clk_rate_in_tol(clk, desired_clk, clk_div, 5); | |
| return ser_clk; | |
| } | |
| static void qcom_geni_serial_set_termios(struct uart_port *uport, | |
| struct ktermios *termios, | |
| const struct ktermios *old) | |
| { | |
| unsigned int baud; | |
| u32 bits_per_char; | |
| u32 tx_trans_cfg; | |
| u32 tx_parity_cfg; | |
| u32 rx_trans_cfg; | |
| u32 rx_parity_cfg; | |
| u32 stop_bit_len; | |
| unsigned int clk_div; | |
| u32 ser_clk_cfg; | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| unsigned long clk_rate; | |
| u32 ver, sampling_rate; | |
| unsigned int avg_bw_core; | |
| unsigned long timeout; | |
| qcom_geni_serial_stop_rx(uport); | |
| /* baud rate */ | |
| baud = uart_get_baud_rate(uport, termios, old, 300, 4000000); | |
| sampling_rate = UART_OVERSAMPLING; | |
| /* Sampling rate is halved for IP versions >= 2.5 */ | |
| ver = geni_se_get_qup_hw_version(&port->se); | |
| if (ver >= QUP_SE_VERSION_2_5) | |
| sampling_rate /= 2; | |
| clk_rate = get_clk_div_rate(port->se.clk, baud, | |
| sampling_rate, &clk_div); | |
| if (!clk_rate) { | |
| dev_err(port->se.dev, | |
| "Couldn't find suitable clock rate for %u\n", | |
| baud * sampling_rate); | |
| goto out_restart_rx; | |
| } | |
| dev_dbg(port->se.dev, "desired_rate = %u, clk_rate = %lu, clk_div = %u\n", | |
| baud * sampling_rate, clk_rate, clk_div); | |
| uport->uartclk = clk_rate; | |
| port->clk_rate = clk_rate; | |
| dev_pm_opp_set_rate(uport->dev, clk_rate); | |
| ser_clk_cfg = SER_CLK_EN; | |
| ser_clk_cfg |= clk_div << CLK_DIV_SHFT; | |
| /* | |
| * Bump up BW vote on CPU and CORE path as driver supports FIFO mode | |
| * only. | |
| */ | |
| avg_bw_core = (baud > 115200) ? Bps_to_icc(CORE_2X_50_MHZ) | |
| : GENI_DEFAULT_BW; | |
| port->se.icc_paths[GENI_TO_CORE].avg_bw = avg_bw_core; | |
| port->se.icc_paths[CPU_TO_GENI].avg_bw = Bps_to_icc(baud); | |
| geni_icc_set_bw(&port->se); | |
| /* parity */ | |
| tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG); | |
| tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG); | |
| rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG); | |
| rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG); | |
| if (termios->c_cflag & PARENB) { | |
| tx_trans_cfg |= UART_TX_PAR_EN; | |
| rx_trans_cfg |= UART_RX_PAR_EN; | |
| tx_parity_cfg |= PAR_CALC_EN; | |
| rx_parity_cfg |= PAR_CALC_EN; | |
| if (termios->c_cflag & PARODD) { | |
| tx_parity_cfg |= PAR_ODD; | |
| rx_parity_cfg |= PAR_ODD; | |
| } else if (termios->c_cflag & CMSPAR) { | |
| tx_parity_cfg |= PAR_SPACE; | |
| rx_parity_cfg |= PAR_SPACE; | |
| } else { | |
| tx_parity_cfg |= PAR_EVEN; | |
| rx_parity_cfg |= PAR_EVEN; | |
| } | |
| } else { | |
| tx_trans_cfg &= ~UART_TX_PAR_EN; | |
| rx_trans_cfg &= ~UART_RX_PAR_EN; | |
| tx_parity_cfg &= ~PAR_CALC_EN; | |
| rx_parity_cfg &= ~PAR_CALC_EN; | |
| } | |
| /* bits per char */ | |
| bits_per_char = tty_get_char_size(termios->c_cflag); | |
| /* stop bits */ | |
| if (termios->c_cflag & CSTOPB) | |
| stop_bit_len = TX_STOP_BIT_LEN_2; | |
| else | |
| stop_bit_len = TX_STOP_BIT_LEN_1; | |
| /* flow control, clear the CTS_MASK bit if using flow control. */ | |
| if (termios->c_cflag & CRTSCTS) | |
| tx_trans_cfg &= ~UART_CTS_MASK; | |
| else | |
| tx_trans_cfg |= UART_CTS_MASK; | |
| if (baud) { | |
| uart_update_timeout(uport, termios->c_cflag, baud); | |
| /* | |
| * Make sure that qcom_geni_serial_poll_bitfield() waits for | |
| * the FIFO, two-word intermediate transfer register and shift | |
| * register to clear. | |
| * | |
| * Note that uart_fifo_timeout() also adds a 20 ms margin. | |
| */ | |
| timeout = jiffies_to_usecs(uart_fifo_timeout(uport)); | |
| timeout += 3 * timeout / port->tx_fifo_depth; | |
| WRITE_ONCE(port->poll_timeout_us, timeout); | |
| } | |
| if (!uart_console(uport)) | |
| writel(port->loopback, | |
| uport->membase + SE_UART_LOOPBACK_CFG); | |
| writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); | |
| writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); | |
| writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); | |
| writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); | |
| writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); | |
| writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); | |
| writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); | |
| writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); | |
| writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); | |
| out_restart_rx: | |
| qcom_geni_serial_start_rx(uport); | |
| } | |
| #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE | |
| static int qcom_geni_console_setup(struct console *co, char *options) | |
| { | |
| struct uart_port *uport; | |
| struct qcom_geni_serial_port *port; | |
| int baud = 115200; | |
| int bits = 8; | |
| int parity = 'n'; | |
| int flow = 'n'; | |
| int ret; | |
| if (co->index >= GENI_UART_CONS_PORTS || co->index < 0) | |
| return -ENXIO; | |
| port = get_port_from_line(co->index, true); | |
| if (IS_ERR(port)) { | |
| pr_err("Invalid line %d\n", co->index); | |
| return PTR_ERR(port); | |
| } | |
| uport = &port->uport; | |
| if (unlikely(!uport->membase)) | |
| return -ENXIO; | |
| if (!port->setup) { | |
| ret = qcom_geni_serial_port_setup(uport); | |
| if (ret) | |
| return ret; | |
| } | |
| if (options) | |
| uart_parse_options(options, &baud, &parity, &bits, &flow); | |
| return uart_set_options(uport, co, baud, parity, bits, flow); | |
| } | |
| static void qcom_geni_serial_earlycon_write(struct console *con, | |
| const char *s, unsigned int n) | |
| { | |
| struct earlycon_device *dev = con->data; | |
| __qcom_geni_serial_console_write(&dev->port, s, n); | |
| } | |
| #ifdef CONFIG_CONSOLE_POLL | |
| static int qcom_geni_serial_earlycon_read(struct console *con, | |
| char *s, unsigned int n) | |
| { | |
| struct earlycon_device *dev = con->data; | |
| struct uart_port *uport = &dev->port; | |
| int num_read = 0; | |
| int ch; | |
| while (num_read < n) { | |
| ch = qcom_geni_serial_get_char(uport); | |
| if (ch == NO_POLL_CHAR) | |
| break; | |
| s[num_read++] = ch; | |
| } | |
| return num_read; | |
| } | |
| static void __init qcom_geni_serial_enable_early_read(struct geni_se *se, | |
| struct console *con) | |
| { | |
| geni_se_setup_s_cmd(se, UART_START_READ, 0); | |
| con->read = qcom_geni_serial_earlycon_read; | |
| } | |
| #else | |
| static inline void qcom_geni_serial_enable_early_read(struct geni_se *se, | |
| struct console *con) { } | |
| #endif | |
| static struct qcom_geni_private_data earlycon_private_data; | |
| static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, | |
| const char *opt) | |
| { | |
| struct uart_port *uport = &dev->port; | |
| u32 tx_trans_cfg; | |
| u32 tx_parity_cfg = 0; /* Disable Tx Parity */ | |
| u32 rx_trans_cfg = 0; | |
| u32 rx_parity_cfg = 0; /* Disable Rx Parity */ | |
| u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */ | |
| u32 bits_per_char; | |
| struct geni_se se; | |
| if (!uport->membase) | |
| return -EINVAL; | |
| uport->private_data = &earlycon_private_data; | |
| memset(&se, 0, sizeof(se)); | |
| se.base = uport->membase; | |
| if (geni_se_read_proto(&se) != GENI_SE_UART) | |
| return -ENXIO; | |
| /* | |
| * Ignore Flow control. | |
| * n = 8. | |
| */ | |
| tx_trans_cfg = UART_CTS_MASK; | |
| bits_per_char = BITS_PER_BYTE; | |
| /* | |
| * Make an unconditional cancel on the main sequencer to reset | |
| * it else we could end up in data loss scenarios. | |
| */ | |
| qcom_geni_serial_poll_tx_done(uport); | |
| qcom_geni_serial_abort_rx(uport); | |
| geni_se_config_packing(&se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, | |
| false, true, true); | |
| geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); | |
| geni_se_select_mode(&se, GENI_SE_FIFO); | |
| writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); | |
| writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); | |
| writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); | |
| writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); | |
| writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); | |
| writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); | |
| writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); | |
| dev->con->write = qcom_geni_serial_earlycon_write; | |
| dev->con->setup = NULL; | |
| qcom_geni_serial_enable_early_read(&se, dev->con); | |
| return 0; | |
| } | |
| OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart", | |
| qcom_geni_serial_earlycon_setup); | |
| static int __init console_register(struct uart_driver *drv) | |
| { | |
| return uart_register_driver(drv); | |
| } | |
| static void console_unregister(struct uart_driver *drv) | |
| { | |
| uart_unregister_driver(drv); | |
| } | |
| static struct console cons_ops = { | |
| .name = "ttyMSM", | |
| .write = qcom_geni_serial_console_write, | |
| .device = uart_console_device, | |
| .setup = qcom_geni_console_setup, | |
| .flags = CON_PRINTBUFFER, | |
| .index = -1, | |
| .data = &qcom_geni_console_driver, | |
| }; | |
| static struct uart_driver qcom_geni_console_driver = { | |
| .owner = THIS_MODULE, | |
| .driver_name = "qcom_geni_console", | |
| .dev_name = "ttyMSM", | |
| .nr = GENI_UART_CONS_PORTS, | |
| .cons = &cons_ops, | |
| }; | |
| #else | |
| static int console_register(struct uart_driver *drv) | |
| { | |
| return 0; | |
| } | |
| static void console_unregister(struct uart_driver *drv) | |
| { | |
| } | |
| #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ | |
| static struct uart_driver qcom_geni_uart_driver = { | |
| .owner = THIS_MODULE, | |
| .driver_name = "qcom_geni_uart", | |
| .dev_name = "ttyHS", | |
| .nr = GENI_UART_PORTS, | |
| }; | |
| static void qcom_geni_serial_pm(struct uart_port *uport, | |
| unsigned int new_state, unsigned int old_state) | |
| { | |
| struct qcom_geni_serial_port *port = to_dev_port(uport); | |
| /* If we've never been called, treat it as off */ | |
| if (old_state == UART_PM_STATE_UNDEFINED) | |
| old_state = UART_PM_STATE_OFF; | |
| if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) { | |
| geni_icc_enable(&port->se); | |
| if (port->clk_rate) | |
| dev_pm_opp_set_rate(uport->dev, port->clk_rate); | |
| geni_se_resources_on(&port->se); | |
| } else if (new_state == UART_PM_STATE_OFF && | |
| old_state == UART_PM_STATE_ON) { | |
| geni_se_resources_off(&port->se); | |
| dev_pm_opp_set_rate(uport->dev, 0); | |
| geni_icc_disable(&port->se); | |
| } | |
| } | |
| static const struct uart_ops qcom_geni_console_pops = { | |
| .tx_empty = qcom_geni_serial_tx_empty, | |
| .stop_tx = qcom_geni_serial_stop_tx_fifo, | |
| .start_tx = qcom_geni_serial_start_tx_fifo, | |
| .stop_rx = qcom_geni_serial_stop_rx_fifo, | |
| .start_rx = qcom_geni_serial_start_rx_fifo, | |
| .set_termios = qcom_geni_serial_set_termios, | |
| .startup = qcom_geni_serial_startup, | |
| .request_port = qcom_geni_serial_request_port, | |
| .config_port = qcom_geni_serial_config_port, | |
| .shutdown = qcom_geni_serial_shutdown, | |
| .flush_buffer = qcom_geni_serial_flush_buffer, | |
| .type = qcom_geni_serial_get_type, | |
| .set_mctrl = qcom_geni_serial_set_mctrl, | |
| .get_mctrl = qcom_geni_serial_get_mctrl, | |
| #ifdef CONFIG_CONSOLE_POLL | |
| .poll_get_char = qcom_geni_serial_get_char, | |
| .poll_put_char = qcom_geni_serial_poll_put_char, | |
| .poll_init = qcom_geni_serial_port_setup, | |
| #endif | |
| .pm = qcom_geni_serial_pm, | |
| }; | |
| static const struct uart_ops qcom_geni_uart_pops = { | |
| .tx_empty = qcom_geni_serial_tx_empty, | |
| .stop_tx = qcom_geni_serial_stop_tx_dma, | |
| .start_tx = qcom_geni_serial_start_tx_dma, | |
| .start_rx = qcom_geni_serial_start_rx_dma, | |
| .stop_rx = qcom_geni_serial_stop_rx_dma, | |
| .set_termios = qcom_geni_serial_set_termios, | |
| .startup = qcom_geni_serial_startup, | |
| .request_port = qcom_geni_serial_request_port, | |
| .config_port = qcom_geni_serial_config_port, | |
| .shutdown = qcom_geni_serial_shutdown, | |
| .type = qcom_geni_serial_get_type, | |
| .set_mctrl = qcom_geni_serial_set_mctrl, | |
| .get_mctrl = qcom_geni_serial_get_mctrl, | |
| .pm = qcom_geni_serial_pm, | |
| }; | |
| static int qcom_geni_serial_probe(struct platform_device *pdev) | |
| { | |
| int ret = 0; | |
| int line; | |
| struct qcom_geni_serial_port *port; | |
| struct uart_port *uport; | |
| struct resource *res; | |
| int irq; | |
| struct uart_driver *drv; | |
| const struct qcom_geni_device_data *data; | |
| data = of_device_get_match_data(&pdev->dev); | |
| if (!data) | |
| return -EINVAL; | |
| if (data->console) { | |
| drv = &qcom_geni_console_driver; | |
| line = of_alias_get_id(pdev->dev.of_node, "serial"); | |
| } else { | |
| drv = &qcom_geni_uart_driver; | |
| line = of_alias_get_id(pdev->dev.of_node, "serial"); | |
| if (line == -ENODEV) /* compat with non-standard aliases */ | |
| line = of_alias_get_id(pdev->dev.of_node, "hsuart"); | |
| } | |
| port = get_port_from_line(line, data->console); | |
| if (IS_ERR(port)) { | |
| dev_err(&pdev->dev, "Invalid line %d\n", line); | |
| return PTR_ERR(port); | |
| } | |
| uport = &port->uport; | |
| /* Don't allow 2 drivers to access the same port */ | |
| if (uport->private_data) | |
| return -ENODEV; | |
| uport->dev = &pdev->dev; | |
| port->dev_data = data; | |
| port->se.dev = &pdev->dev; | |
| port->se.wrapper = dev_get_drvdata(pdev->dev.parent); | |
| port->se.clk = devm_clk_get(&pdev->dev, "se"); | |
| if (IS_ERR(port->se.clk)) { | |
| ret = PTR_ERR(port->se.clk); | |
| dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret); | |
| return ret; | |
| } | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| if (!res) | |
| return -EINVAL; | |
| uport->mapbase = res->start; | |
| port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS; | |
| port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS; | |
| port->tx_fifo_width = DEF_FIFO_WIDTH_BITS; | |
| if (!data->console) { | |
| port->rx_buf = devm_kzalloc(uport->dev, | |
| DMA_RX_BUF_SIZE, GFP_KERNEL); | |
| if (!port->rx_buf) | |
| return -ENOMEM; | |
| } | |
| ret = geni_icc_get(&port->se, NULL); | |
| if (ret) | |
| return ret; | |
| port->se.icc_paths[GENI_TO_CORE].avg_bw = GENI_DEFAULT_BW; | |
| port->se.icc_paths[CPU_TO_GENI].avg_bw = GENI_DEFAULT_BW; | |
| /* Set BW for register access */ | |
| ret = geni_icc_set_bw(&port->se); | |
| if (ret) | |
| return ret; | |
| port->name = devm_kasprintf(uport->dev, GFP_KERNEL, | |
| "qcom_geni_serial_%s%d", | |
| uart_console(uport) ? "console" : "uart", uport->line); | |
| if (!port->name) | |
| return -ENOMEM; | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq < 0) | |
| return irq; | |
| uport->irq = irq; | |
| uport->has_sysrq = IS_ENABLED(CONFIG_SERIAL_QCOM_GENI_CONSOLE); | |
| if (!data->console) | |
| port->wakeup_irq = platform_get_irq_optional(pdev, 1); | |
| if (of_property_read_bool(pdev->dev.of_node, "rx-tx-swap")) | |
| port->rx_tx_swap = true; | |
| if (of_property_read_bool(pdev->dev.of_node, "cts-rts-swap")) | |
| port->cts_rts_swap = true; | |
| ret = devm_pm_opp_set_clkname(&pdev->dev, "se"); | |
| if (ret) | |
| return ret; | |
| /* OPP table is optional */ | |
| ret = devm_pm_opp_of_add_table(&pdev->dev); | |
| if (ret && ret != -ENODEV) { | |
| dev_err(&pdev->dev, "invalid OPP table in device tree\n"); | |
| return ret; | |
| } | |
| port->private_data.drv = drv; | |
| uport->private_data = &port->private_data; | |
| platform_set_drvdata(pdev, port); | |
| irq_set_status_flags(uport->irq, IRQ_NOAUTOEN); | |
| ret = devm_request_irq(uport->dev, uport->irq, qcom_geni_serial_isr, | |
| IRQF_TRIGGER_HIGH, port->name, uport); | |
| if (ret) { | |
| dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret); | |
| return ret; | |
| } | |
| ret = uart_add_one_port(drv, uport); | |
| if (ret) | |
| return ret; | |
| if (port->wakeup_irq > 0) { | |
| device_init_wakeup(&pdev->dev, true); | |
| ret = dev_pm_set_dedicated_wake_irq(&pdev->dev, | |
| port->wakeup_irq); | |
| if (ret) { | |
| device_init_wakeup(&pdev->dev, false); | |
| uart_remove_one_port(drv, uport); | |
| return ret; | |
| } | |
| } | |
| return 0; | |
| } | |
| static void qcom_geni_serial_remove(struct platform_device *pdev) | |
| { | |
| struct qcom_geni_serial_port *port = platform_get_drvdata(pdev); | |
| struct uart_driver *drv = port->private_data.drv; | |
| dev_pm_clear_wake_irq(&pdev->dev); | |
| device_init_wakeup(&pdev->dev, false); | |
| uart_remove_one_port(drv, &port->uport); | |
| } | |
| static int qcom_geni_serial_sys_suspend(struct device *dev) | |
| { | |
| struct qcom_geni_serial_port *port = dev_get_drvdata(dev); | |
| struct uart_port *uport = &port->uport; | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| /* | |
| * This is done so we can hit the lowest possible state in suspend | |
| * even with no_console_suspend | |
| */ | |
| if (uart_console(uport)) { | |
| geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ACTIVE_ONLY); | |
| geni_icc_set_bw(&port->se); | |
| } | |
| return uart_suspend_port(private_data->drv, uport); | |
| } | |
| static int qcom_geni_serial_sys_resume(struct device *dev) | |
| { | |
| int ret; | |
| struct qcom_geni_serial_port *port = dev_get_drvdata(dev); | |
| struct uart_port *uport = &port->uport; | |
| struct qcom_geni_private_data *private_data = uport->private_data; | |
| ret = uart_resume_port(private_data->drv, uport); | |
| if (uart_console(uport)) { | |
| geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ALWAYS); | |
| geni_icc_set_bw(&port->se); | |
| } | |
| return ret; | |
| } | |
| static int qcom_geni_serial_sys_hib_resume(struct device *dev) | |
| { | |
| int ret = 0; | |
| struct uart_port *uport; | |
| struct qcom_geni_private_data *private_data; | |
| struct qcom_geni_serial_port *port = dev_get_drvdata(dev); | |
| uport = &port->uport; | |
| private_data = uport->private_data; | |
| if (uart_console(uport)) { | |
| geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ALWAYS); | |
| geni_icc_set_bw(&port->se); | |
| ret = uart_resume_port(private_data->drv, uport); | |
| /* | |
| * For hibernation usecase clients for | |
| * console UART won't call port setup during restore, | |
| * hence call port setup for console uart. | |
| */ | |
| qcom_geni_serial_port_setup(uport); | |
| } else { | |
| /* | |
| * Peripheral register settings are lost during hibernation. | |
| * Update setup flag such that port setup happens again | |
| * during next session. Clients of HS-UART will close and | |
| * open the port during hibernation. | |
| */ | |
| port->setup = false; | |
| } | |
| return ret; | |
| } | |
| static const struct qcom_geni_device_data qcom_geni_console_data = { | |
| .console = true, | |
| .mode = GENI_SE_FIFO, | |
| }; | |
| static const struct qcom_geni_device_data qcom_geni_uart_data = { | |
| .console = false, | |
| .mode = GENI_SE_DMA, | |
| }; | |
| static const struct dev_pm_ops qcom_geni_serial_pm_ops = { | |
| .suspend = pm_sleep_ptr(qcom_geni_serial_sys_suspend), | |
| .resume = pm_sleep_ptr(qcom_geni_serial_sys_resume), | |
| .freeze = pm_sleep_ptr(qcom_geni_serial_sys_suspend), | |
| .poweroff = pm_sleep_ptr(qcom_geni_serial_sys_suspend), | |
| .restore = pm_sleep_ptr(qcom_geni_serial_sys_hib_resume), | |
| .thaw = pm_sleep_ptr(qcom_geni_serial_sys_hib_resume), | |
| }; | |
| static const struct of_device_id qcom_geni_serial_match_table[] = { | |
| { | |
| .compatible = "qcom,geni-debug-uart", | |
| .data = &qcom_geni_console_data, | |
| }, | |
| { | |
| .compatible = "qcom,geni-uart", | |
| .data = &qcom_geni_uart_data, | |
| }, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table); | |
| static struct platform_driver qcom_geni_serial_platform_driver = { | |
| .remove_new = qcom_geni_serial_remove, | |
| .probe = qcom_geni_serial_probe, | |
| .driver = { | |
| .name = "qcom_geni_serial", | |
| .of_match_table = qcom_geni_serial_match_table, | |
| .pm = &qcom_geni_serial_pm_ops, | |
| }, | |
| }; | |
| static int __init qcom_geni_serial_init(void) | |
| { | |
| int ret; | |
| ret = console_register(&qcom_geni_console_driver); | |
| if (ret) | |
| return ret; | |
| ret = uart_register_driver(&qcom_geni_uart_driver); | |
| if (ret) { | |
| console_unregister(&qcom_geni_console_driver); | |
| return ret; | |
| } | |
| ret = platform_driver_register(&qcom_geni_serial_platform_driver); | |
| if (ret) { | |
| console_unregister(&qcom_geni_console_driver); | |
| uart_unregister_driver(&qcom_geni_uart_driver); | |
| } | |
| return ret; | |
| } | |
| module_init(qcom_geni_serial_init); | |
| static void __exit qcom_geni_serial_exit(void) | |
| { | |
| platform_driver_unregister(&qcom_geni_serial_platform_driver); | |
| console_unregister(&qcom_geni_console_driver); | |
| uart_unregister_driver(&qcom_geni_uart_driver); | |
| } | |
| module_exit(qcom_geni_serial_exit); | |
| MODULE_DESCRIPTION("Serial driver for GENI based QUP cores"); | |
| MODULE_LICENSE("GPL v2"); |