blob: 365f511186ca3cdca8ca55896170a77652c8c87e [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* GE SBC610 board support
*
* Author: Martyn Welch <martyn.welch@ge.com>
*
* Copyright 2008 GE Intelligent Platforms Embedded Systems, Inc.
*
* Based on: mpc86xx_hpcn.c (MPC86xx HPCN board specific routines)
* Copyright 2006 Freescale Semiconductor Inc.
*
* NEC fixup adapted from arch/mips/pci/fixup-lm2e.c
*/
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/pci-bridge.h>
#include <mm/mmu_decl.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
#include <asm/nvram.h>
#include <sysdev/fsl_pci.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/ge/ge_pic.h>
#include "mpc86xx.h"
#undef DEBUG
#ifdef DEBUG
#define DBG (fmt...) do { printk(KERN_ERR "SBC610: " fmt); } while (0)
#else
#define DBG (fmt...) do { } while (0)
#endif
void __iomem *sbc610_regs;
static void __init gef_sbc610_init_irq(void)
{
struct device_node *cascade_node = NULL;
mpc86xx_init_irq();
/*
* There is a simple interrupt handler in the main FPGA, this needs
* to be cascaded into the MPIC
*/
cascade_node = of_find_compatible_node(NULL, NULL, "gef,fpga-pic");
if (!cascade_node) {
printk(KERN_WARNING "SBC610: No FPGA PIC\n");
return;
}
gef_pic_init(cascade_node);
of_node_put(cascade_node);
}
static void __init gef_sbc610_setup_arch(void)
{
struct device_node *regs;
printk(KERN_INFO "GE Intelligent Platforms SBC610 6U VPX SBC\n");
#ifdef CONFIG_SMP
mpc86xx_smp_init();
#endif
fsl_pci_assign_primary();
/* Remap basic board registers */
regs = of_find_compatible_node(NULL, NULL, "gef,fpga-regs");
if (regs) {
sbc610_regs = of_iomap(regs, 0);
if (sbc610_regs == NULL)
printk(KERN_WARNING "Unable to map board registers\n");
of_node_put(regs);
}
#if defined(CONFIG_MMIO_NVRAM)
mmio_nvram_init();
#endif
}
/* Return the PCB revision */
static unsigned int gef_sbc610_get_pcb_rev(void)
{
unsigned int reg;
reg = ioread32(sbc610_regs);
return (reg >> 8) & 0xff;
}
/* Return the board (software) revision */
static unsigned int gef_sbc610_get_board_rev(void)
{
unsigned int reg;
reg = ioread32(sbc610_regs);
return (reg >> 16) & 0xff;
}
/* Return the FPGA revision */
static unsigned int gef_sbc610_get_fpga_rev(void)
{
unsigned int reg;
reg = ioread32(sbc610_regs);
return (reg >> 24) & 0xf;
}
static void gef_sbc610_show_cpuinfo(struct seq_file *m)
{
uint svid = mfspr(SPRN_SVR);
seq_printf(m, "Vendor\t\t: GE Intelligent Platforms\n");
seq_printf(m, "Revision\t: %u%c\n", gef_sbc610_get_pcb_rev(),
('A' + gef_sbc610_get_board_rev() - 1));
seq_printf(m, "FPGA Revision\t: %u\n", gef_sbc610_get_fpga_rev());
seq_printf(m, "SVR\t\t: 0x%x\n", svid);
}
static void gef_sbc610_nec_fixup(struct pci_dev *pdev)
{
unsigned int val;
/* Do not do the fixup on other platforms! */
if (!machine_is(gef_sbc610))
return;
printk(KERN_INFO "Running NEC uPD720101 Fixup\n");
/* Ensure ports 1, 2, 3, 4 & 5 are enabled */
pci_read_config_dword(pdev, 0xe0, &val);
pci_write_config_dword(pdev, 0xe0, (val & ~7) | 0x5);
/* System clock is 48-MHz Oscillator and EHCI Enabled. */
pci_write_config_dword(pdev, 0xe4, 1 << 5);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB,
gef_sbc610_nec_fixup);
machine_arch_initcall(gef_sbc610, mpc86xx_common_publish_devices);
define_machine(gef_sbc610) {
.name = "GE SBC610",
.compatible = "gef,sbc610",
.setup_arch = gef_sbc610_setup_arch,
.init_IRQ = gef_sbc610_init_irq,
.show_cpuinfo = gef_sbc610_show_cpuinfo,
.get_irq = mpic_get_irq,
.time_init = mpc86xx_time_init,
.progress = udbg_progress,
#ifdef CONFIG_PCI
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
};