| /* SPDX-License-Identifier: GPL-2.0-only */ |
| /* |
| * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com) |
| * Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com) |
| * |
| * Vineetg: March 2009 (Supporting 2 levels of Interrupts) |
| * Stack switching code can no longer reliably rely on the fact that |
| * if we are NOT in user mode, stack is switched to kernel mode. |
| * e.g. L2 IRQ interrupted a L1 ISR which had not yet completed |
| * it's prologue including stack switching from user mode |
| * |
| * Vineetg: Aug 28th 2008: Bug #94984 |
| * -Zero Overhead Loop Context shd be cleared when entering IRQ/EXcp/Trap |
| * Normally CPU does this automatically, however when doing FAKE rtie, |
| * we also need to explicitly do this. The problem in macros |
| * FAKE_RET_FROM_EXCPN and FAKE_RET_FROM_EXCPN_LOCK_IRQ was that this bit |
| * was being "CLEARED" rather then "SET". Actually "SET" clears ZOL context |
| * |
| * Vineetg: May 5th 2008 |
| * -Modified CALLEE_REG save/restore macros to handle the fact that |
| * r25 contains the kernel current task ptr |
| * - Defined Stack Switching Macro to be reused in all intr/excp hdlrs |
| * - Shaved off 11 instructions from RESTORE_ALL_INT1 by using the |
| * address Write back load ld.ab instead of separate ld/add instn |
| * |
| * Amit Bhor, Sameer Dhavale: Codito Technologies 2004 |
| */ |
| |
| #ifndef __ASM_ARC_ENTRY_COMPACT_H |
| #define __ASM_ARC_ENTRY_COMPACT_H |
| |
| #include <asm/asm-offsets.h> |
| #include <asm/irqflags-compact.h> |
| #include <asm/thread_info.h> /* For THREAD_SIZE */ |
| |
| /* Note on the LD/ST addr modes with addr reg wback |
| * |
| * LD.a same as LD.aw |
| * |
| * LD.a reg1, [reg2, x] => Pre Incr |
| * Eff Addr for load = [reg2 + x] |
| * |
| * LD.ab reg1, [reg2, x] => Post Incr |
| * Eff Addr for load = [reg2] |
| */ |
| |
| .macro PUSHAX aux |
| lr r9, [\aux] |
| push r9 |
| .endm |
| |
| .macro POPAX aux |
| pop r9 |
| sr r9, [\aux] |
| .endm |
| |
| .macro SAVE_R0_TO_R12 |
| push r0 |
| push r1 |
| push r2 |
| push r3 |
| push r4 |
| push r5 |
| push r6 |
| push r7 |
| push r8 |
| push r9 |
| push r10 |
| push r11 |
| push r12 |
| .endm |
| |
| .macro RESTORE_R12_TO_R0 |
| pop r12 |
| pop r11 |
| pop r10 |
| pop r9 |
| pop r8 |
| pop r7 |
| pop r6 |
| pop r5 |
| pop r4 |
| pop r3 |
| pop r2 |
| pop r1 |
| pop r0 |
| .endm |
| |
| .macro SAVE_ABI_CALLEE_REGS |
| push r13 |
| push r14 |
| push r15 |
| push r16 |
| push r17 |
| push r18 |
| push r19 |
| push r20 |
| push r21 |
| push r22 |
| push r23 |
| push r24 |
| push r25 |
| .endm |
| |
| .macro RESTORE_ABI_CALLEE_REGS |
| pop r25 |
| pop r24 |
| pop r23 |
| pop r22 |
| pop r21 |
| pop r20 |
| pop r19 |
| pop r18 |
| pop r17 |
| pop r16 |
| pop r15 |
| pop r14 |
| pop r13 |
| .endm |
| |
| /*-------------------------------------------------------------- |
| * Switch to Kernel Mode stack if SP points to User Mode stack |
| * |
| * Entry : r9 contains pre-IRQ/exception/trap status32 |
| * Exit : SP set to K mode stack |
| * SP at the time of entry (K/U) saved @ pt_regs->sp |
| * Clobbers: r9 |
| *-------------------------------------------------------------*/ |
| |
| .macro SWITCH_TO_KERNEL_STK |
| |
| /* User Mode when this happened ? Yes: Proceed to switch stack */ |
| bbit1 r9, STATUS_U_BIT, 88f |
| |
| /* OK we were already in kernel mode when this event happened, thus can |
| * assume SP is kernel mode SP. _NO_ need to do any stack switching |
| */ |
| |
| #ifdef CONFIG_ARC_COMPACT_IRQ_LEVELS |
| /* However.... |
| * If Level 2 Interrupts enabled, we may end up with a corner case: |
| * 1. User Task executing |
| * 2. L1 IRQ taken, ISR starts (CPU auto-switched to KERNEL mode) |
| * 3. But before it could switch SP from USER to KERNEL stack |
| * a L2 IRQ "Interrupts" L1 |
| * Thay way although L2 IRQ happened in Kernel mode, stack is still |
| * not switched. |
| * To handle this, we may need to switch stack even if in kernel mode |
| * provided SP has values in range of USER mode stack ( < 0x7000_0000 ) |
| */ |
| brlo sp, VMALLOC_START, 88f |
| |
| /* TODO: vineetg: |
| * We need to be a bit more cautious here. What if a kernel bug in |
| * L1 ISR, caused SP to go whaco (some small value which looks like |
| * USER stk) and then we take L2 ISR. |
| * Above brlo alone would treat it as a valid L1-L2 scenario |
| * instead of shouting around |
| * The only feasible way is to make sure this L2 happened in |
| * L1 prelogue ONLY i.e. ilink2 is less than a pre-set marker in |
| * L1 ISR before it switches stack |
| */ |
| |
| #endif |
| |
| /*------Intr/Ecxp happened in kernel mode, SP already setup ------ */ |
| /* save it nevertheless @ pt_regs->sp for uniformity */ |
| |
| b.d 66f |
| st sp, [sp, PT_sp - SZ_PT_REGS] |
| |
| 88: /*------Intr/Ecxp happened in user mode, "switch" stack ------ */ |
| |
| GET_CURR_TASK_ON_CPU r9 |
| |
| /* With current tsk in r9, get it's kernel mode stack base */ |
| GET_TSK_STACK_BASE r9, r9 |
| |
| /* save U mode SP @ pt_regs->sp */ |
| st sp, [r9, PT_sp - SZ_PT_REGS] |
| |
| /* final SP switch */ |
| mov sp, r9 |
| 66: |
| .endm |
| |
| /*------------------------------------------------------------ |
| * "FAKE" a rtie to return from CPU Exception context |
| * This is to re-enable Exceptions within exception |
| * Look at EV_ProtV to see how this is actually used |
| *-------------------------------------------------------------*/ |
| |
| .macro FAKE_RET_FROM_EXCPN |
| |
| lr r9, [status32] |
| bclr r9, r9, STATUS_AE_BIT |
| or r9, r9, (STATUS_E1_MASK|STATUS_E2_MASK) |
| sr r9, [erstatus] |
| mov r9, 55f |
| sr r9, [eret] |
| rtie |
| 55: |
| .endm |
| |
| /*-------------------------------------------------------------- |
| * For early Exception/ISR Prologue, a core reg is temporarily needed to |
| * code the rest of prolog (stack switching). This is done by stashing |
| * it to memory (non-SMP case) or SCRATCH0 Aux Reg (SMP). |
| * |
| * Before saving the full regfile - this reg is restored back, only |
| * to be saved again on kernel mode stack, as part of pt_regs. |
| *-------------------------------------------------------------*/ |
| .macro PROLOG_FREEUP_REG reg, mem |
| st \reg, [\mem] |
| .endm |
| |
| .macro PROLOG_RESTORE_REG reg, mem |
| ld \reg, [\mem] |
| .endm |
| |
| /*-------------------------------------------------------------- |
| * Exception Entry prologue |
| * -Switches stack to K mode (if not already) |
| * -Saves the register file |
| * |
| * After this it is safe to call the "C" handlers |
| *-------------------------------------------------------------*/ |
| .macro EXCEPTION_PROLOGUE_KEEP_AE |
| |
| /* Need at least 1 reg to code the early exception prologue */ |
| PROLOG_FREEUP_REG r9, @ex_saved_reg1 |
| |
| /* U/K mode at time of exception (stack not switched if already K) */ |
| lr r9, [erstatus] |
| |
| /* ARC700 doesn't provide auto-stack switching */ |
| SWITCH_TO_KERNEL_STK |
| |
| st.a r0, [sp, -8] /* orig_r0 needed for syscall (skip ECR slot) */ |
| sub sp, sp, 4 /* skip pt_regs->sp, already saved above */ |
| |
| /* Restore r9 used to code the early prologue */ |
| PROLOG_RESTORE_REG r9, @ex_saved_reg1 |
| |
| /* now we are ready to save the regfile */ |
| SAVE_R0_TO_R12 |
| PUSH gp |
| PUSH fp |
| PUSH blink |
| PUSHAX eret |
| PUSHAX erstatus |
| PUSH lp_count |
| PUSHAX lp_end |
| PUSHAX lp_start |
| PUSHAX erbta |
| |
| lr r10, [ecr] |
| st r10, [sp, PT_event] |
| |
| #ifdef CONFIG_ARC_CURR_IN_REG |
| /* gp already saved on stack: now load with "current" */ |
| GET_CURR_TASK_ON_CPU gp |
| #endif |
| ; OUTPUT: r10 has ECR expected by EV_Trap |
| .endm |
| |
| .macro EXCEPTION_PROLOGUE |
| |
| EXCEPTION_PROLOGUE_KEEP_AE ; return ECR in r10 |
| |
| lr r0, [efa] |
| mov r1, sp |
| |
| FAKE_RET_FROM_EXCPN ; clobbers r9 |
| .endm |
| |
| /*-------------------------------------------------------------- |
| * Restore all registers used by system call or Exceptions |
| * SP should always be pointing to the next free stack element |
| * when entering this macro. |
| * |
| * NOTE: |
| * |
| * It is recommended that lp_count/ilink1/ilink2 not be used as a dest reg |
| * for memory load operations. If used in that way interrupts are deffered |
| * by hardware and that is not good. |
| *-------------------------------------------------------------*/ |
| .macro EXCEPTION_EPILOGUE |
| |
| POPAX erbta |
| POPAX lp_start |
| POPAX lp_end |
| |
| POP r9 |
| mov lp_count, r9 ;LD to lp_count is not allowed |
| |
| POPAX erstatus |
| POPAX eret |
| POP blink |
| POP fp |
| POP gp |
| RESTORE_R12_TO_R0 |
| |
| ld sp, [sp] /* restore original sp */ |
| /* orig_r0, ECR skipped automatically */ |
| .endm |
| |
| /* Dummy ECR values for Interrupts */ |
| #define event_IRQ1 0x0031abcd |
| #define event_IRQ2 0x0032abcd |
| |
| .macro INTERRUPT_PROLOGUE LVL |
| |
| /* free up r9 as scratchpad */ |
| PROLOG_FREEUP_REG r9, @int\LVL\()_saved_reg |
| |
| /* Which mode (user/kernel) was the system in when intr occurred */ |
| lr r9, [status32_l\LVL\()] |
| |
| SWITCH_TO_KERNEL_STK |
| |
| |
| st.a 0x003\LVL\()abcd, [sp, -4] /* Dummy ECR */ |
| sub sp, sp, 8 /* skip orig_r0 (not needed) |
| skip pt_regs->sp, already saved above */ |
| |
| /* Restore r9 used to code the early prologue */ |
| PROLOG_RESTORE_REG r9, @int\LVL\()_saved_reg |
| |
| SAVE_R0_TO_R12 |
| PUSH gp |
| PUSH fp |
| PUSH blink |
| PUSH ilink\LVL\() |
| PUSHAX status32_l\LVL\() |
| PUSH lp_count |
| PUSHAX lp_end |
| PUSHAX lp_start |
| PUSHAX bta_l\LVL\() |
| |
| #ifdef CONFIG_ARC_CURR_IN_REG |
| /* gp already saved on stack: now load with "current" */ |
| GET_CURR_TASK_ON_CPU gp |
| #endif |
| .endm |
| |
| /*-------------------------------------------------------------- |
| * Restore all registers used by interrupt handlers. |
| * |
| * NOTE: |
| * |
| * It is recommended that lp_count/ilink1/ilink2 not be used as a dest reg |
| * for memory load operations. If used in that way interrupts are deffered |
| * by hardware and that is not good. |
| *-------------------------------------------------------------*/ |
| .macro INTERRUPT_EPILOGUE LVL |
| |
| POPAX bta_l\LVL\() |
| POPAX lp_start |
| POPAX lp_end |
| |
| POP r9 |
| mov lp_count, r9 ;LD to lp_count is not allowed |
| |
| POPAX status32_l\LVL\() |
| POP ilink\LVL\() |
| POP blink |
| POP fp |
| POP gp |
| RESTORE_R12_TO_R0 |
| |
| ld sp, [sp] /* restore original sp; orig_r0, ECR skipped implicitly */ |
| .endm |
| |
| /* Get thread_info of "current" tsk */ |
| .macro GET_CURR_THR_INFO_FROM_SP reg |
| bic \reg, sp, (THREAD_SIZE - 1) |
| .endm |
| |
| /* Get CPU-ID of this core */ |
| .macro GET_CPU_ID reg |
| lr \reg, [identity] |
| lsr \reg, \reg, 8 |
| bmsk \reg, \reg, 7 |
| .endm |
| |
| #endif /* __ASM_ARC_ENTRY_COMPACT_H */ |
