blob: 10a465686439e0d1f2876f8b4cb8a6176cf18ff5 [file] [log] [blame]
/*
* Copyright (c) 2014 Redpine Signals Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include <linux/module.h>
#include <linux/types.h>
#include <net/rsi_91x.h>
#include "rsi_usb.h"
#include "rsi_hal.h"
#include "rsi_coex.h"
/* Default operating mode is wlan STA + BT */
static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL;
module_param(dev_oper_mode, ushort, 0444);
MODULE_PARM_DESC(dev_oper_mode, DEV_OPMODE_PARAM_DESC);
static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t flags);
/**
* rsi_usb_card_write() - This function writes to the USB Card.
* @adapter: Pointer to the adapter structure.
* @buf: Pointer to the buffer from where the data has to be taken.
* @len: Length to be written.
* @endpoint: Type of endpoint.
*
* Return: status: 0 on success, a negative error code on failure.
*/
static int rsi_usb_card_write(struct rsi_hw *adapter,
u8 *buf,
u16 len,
u8 endpoint)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
int status;
u8 *seg = dev->tx_buffer;
int transfer;
int ep = dev->bulkout_endpoint_addr[endpoint - 1];
memset(seg, 0, len + RSI_USB_TX_HEAD_ROOM);
memcpy(seg + RSI_USB_TX_HEAD_ROOM, buf, len);
len += RSI_USB_TX_HEAD_ROOM;
transfer = len;
status = usb_bulk_msg(dev->usbdev,
usb_sndbulkpipe(dev->usbdev, ep),
(void *)seg,
(int)len,
&transfer,
USB_CTRL_SET_TIMEOUT);
if (status < 0) {
rsi_dbg(ERR_ZONE,
"Card write failed with error code :%10d\n", status);
dev->write_fail = 1;
}
return status;
}
/**
* rsi_write_multiple() - This function writes multiple bytes of information
* to the USB card.
* @adapter: Pointer to the adapter structure.
* @endpoint: Type of endpoint.
* @data: Pointer to the data that has to be written.
* @count: Number of multiple bytes to be written.
*
* Return: 0 on success, a negative error code on failure.
*/
static int rsi_write_multiple(struct rsi_hw *adapter,
u8 endpoint,
u8 *data,
u32 count)
{
struct rsi_91x_usbdev *dev;
if (!adapter)
return -ENODEV;
if (endpoint == 0)
return -EINVAL;
dev = adapter->rsi_dev;
if (dev->write_fail)
return -ENETDOWN;
return rsi_usb_card_write(adapter, data, count, endpoint);
}
/**
* rsi_find_bulk_in_and_out_endpoints() - This function initializes the bulk
* endpoints to the device.
* @interface: Pointer to the USB interface structure.
* @adapter: Pointer to the adapter structure.
*
* Return: ret_val: 0 on success, -ENOMEM on failure.
*/
static int rsi_find_bulk_in_and_out_endpoints(struct usb_interface *interface,
struct rsi_hw *adapter)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
struct usb_host_interface *iface_desc;
struct usb_endpoint_descriptor *endpoint;
__le16 buffer_size;
int ii, bin_found = 0, bout_found = 0;
iface_desc = interface->cur_altsetting;
for (ii = 0; ii < iface_desc->desc.bNumEndpoints; ++ii) {
endpoint = &(iface_desc->endpoint[ii].desc);
if (!dev->bulkin_endpoint_addr[bin_found] &&
(endpoint->bEndpointAddress & USB_DIR_IN) &&
((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
USB_ENDPOINT_XFER_BULK)) {
buffer_size = endpoint->wMaxPacketSize;
dev->bulkin_size[bin_found] = buffer_size;
dev->bulkin_endpoint_addr[bin_found] =
endpoint->bEndpointAddress;
bin_found++;
}
if (!dev->bulkout_endpoint_addr[bout_found] &&
!(endpoint->bEndpointAddress & USB_DIR_IN) &&
((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
USB_ENDPOINT_XFER_BULK)) {
buffer_size = endpoint->wMaxPacketSize;
dev->bulkout_endpoint_addr[bout_found] =
endpoint->bEndpointAddress;
dev->bulkout_size[bout_found] = buffer_size;
bout_found++;
}
if (bin_found >= MAX_BULK_EP || bout_found >= MAX_BULK_EP)
break;
}
if (!(dev->bulkin_endpoint_addr[0] && dev->bulkout_endpoint_addr[0])) {
dev_err(&interface->dev, "missing wlan bulk endpoints\n");
return -EINVAL;
}
if (adapter->priv->coex_mode > 1) {
if (!dev->bulkin_endpoint_addr[1]) {
dev_err(&interface->dev, "missing bt bulk-in endpoint\n");
return -EINVAL;
}
}
return 0;
}
#define RSI_USB_REQ_OUT (USB_TYPE_VENDOR | USB_DIR_OUT | USB_RECIP_DEVICE)
#define RSI_USB_REQ_IN (USB_TYPE_VENDOR | USB_DIR_IN | USB_RECIP_DEVICE)
/* rsi_usb_reg_read() - This function reads data from given register address.
* @usbdev: Pointer to the usb_device structure.
* @reg: Address of the register to be read.
* @value: Value to be read.
* @len: length of data to be read.
*
* Return: status: 0 on success, a negative error code on failure.
*/
static int rsi_usb_reg_read(struct usb_device *usbdev,
u32 reg,
u16 *value,
u16 len)
{
u8 *buf;
int status = -ENOMEM;
if (len > RSI_USB_CTRL_BUF_SIZE)
return -EINVAL;
buf = kmalloc(RSI_USB_CTRL_BUF_SIZE, GFP_KERNEL);
if (!buf)
return status;
status = usb_control_msg(usbdev,
usb_rcvctrlpipe(usbdev, 0),
USB_VENDOR_REGISTER_READ,
RSI_USB_REQ_IN,
((reg & 0xffff0000) >> 16), (reg & 0xffff),
(void *)buf,
len,
USB_CTRL_GET_TIMEOUT);
*value = (buf[0] | (buf[1] << 8));
if (status < 0) {
rsi_dbg(ERR_ZONE,
"%s: Reg read failed with error code :%d\n",
__func__, status);
}
kfree(buf);
return status;
}
/**
* rsi_usb_reg_write() - This function writes the given data into the given
* register address.
* @usbdev: Pointer to the usb_device structure.
* @reg: Address of the register.
* @value: Value to write.
* @len: Length of data to be written.
*
* Return: status: 0 on success, a negative error code on failure.
*/
static int rsi_usb_reg_write(struct usb_device *usbdev,
u32 reg,
u32 value,
u16 len)
{
u8 *usb_reg_buf;
int status = -ENOMEM;
if (len > RSI_USB_CTRL_BUF_SIZE)
return -EINVAL;
usb_reg_buf = kmalloc(RSI_USB_CTRL_BUF_SIZE, GFP_KERNEL);
if (!usb_reg_buf)
return status;
usb_reg_buf[0] = (cpu_to_le32(value) & 0x00ff);
usb_reg_buf[1] = (cpu_to_le32(value) & 0xff00) >> 8;
usb_reg_buf[2] = (cpu_to_le32(value) & 0x00ff0000) >> 16;
usb_reg_buf[3] = (cpu_to_le32(value) & 0xff000000) >> 24;
status = usb_control_msg(usbdev,
usb_sndctrlpipe(usbdev, 0),
USB_VENDOR_REGISTER_WRITE,
RSI_USB_REQ_OUT,
((cpu_to_le32(reg) & 0xffff0000) >> 16),
(cpu_to_le32(reg) & 0xffff),
(void *)usb_reg_buf,
len,
USB_CTRL_SET_TIMEOUT);
if (status < 0) {
rsi_dbg(ERR_ZONE,
"%s: Reg write failed with error code :%d\n",
__func__, status);
}
kfree(usb_reg_buf);
return status;
}
/**
* rsi_rx_done_handler() - This function is called when a packet is received
* from USB stack. This is callback to receive done.
* @urb: Received URB.
*
* Return: None.
*/
static void rsi_rx_done_handler(struct urb *urb)
{
struct rx_usb_ctrl_block *rx_cb = urb->context;
struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)rx_cb->data;
int status = -EINVAL;
if (!rx_cb->rx_skb)
return;
if (urb->status) {
dev_kfree_skb(rx_cb->rx_skb);
rx_cb->rx_skb = NULL;
return;
}
if (urb->actual_length <= 0 ||
urb->actual_length > rx_cb->rx_skb->len) {
rsi_dbg(INFO_ZONE, "%s: Invalid packet length = %d\n",
__func__, urb->actual_length);
goto out;
}
if (skb_queue_len(&dev->rx_q) >= RSI_MAX_RX_PKTS) {
rsi_dbg(INFO_ZONE, "Max RX packets reached\n");
goto out;
}
skb_trim(rx_cb->rx_skb, urb->actual_length);
skb_queue_tail(&dev->rx_q, rx_cb->rx_skb);
rsi_set_event(&dev->rx_thread.event);
status = 0;
out:
if (rsi_rx_urb_submit(dev->priv, rx_cb->ep_num, GFP_ATOMIC))
rsi_dbg(ERR_ZONE, "%s: Failed in urb submission", __func__);
if (status) {
dev_kfree_skb(rx_cb->rx_skb);
rx_cb->rx_skb = NULL;
}
}
static void rsi_rx_urb_kill(struct rsi_hw *adapter, u8 ep_num)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
struct rx_usb_ctrl_block *rx_cb = &dev->rx_cb[ep_num - 1];
struct urb *urb = rx_cb->rx_urb;
usb_kill_urb(urb);
}
/**
* rsi_rx_urb_submit() - This function submits the given URB to the USB stack.
* @adapter: Pointer to the adapter structure.
* @ep_num: Endpoint number.
* @mem_flags: The type of memory to allocate.
*
* Return: 0 on success, a negative error code on failure.
*/
static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t mem_flags)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
struct rx_usb_ctrl_block *rx_cb = &dev->rx_cb[ep_num - 1];
struct urb *urb = rx_cb->rx_urb;
int status;
struct sk_buff *skb;
u8 dword_align_bytes = 0;
skb = dev_alloc_skb(RSI_MAX_RX_USB_PKT_SIZE);
if (!skb)
return -ENOMEM;
skb_reserve(skb, MAX_DWORD_ALIGN_BYTES);
skb_put(skb, RSI_MAX_RX_USB_PKT_SIZE - MAX_DWORD_ALIGN_BYTES);
dword_align_bytes = (unsigned long)skb->data & 0x3f;
if (dword_align_bytes > 0)
skb_push(skb, dword_align_bytes);
urb->transfer_buffer = skb->data;
rx_cb->rx_skb = skb;
usb_fill_bulk_urb(urb,
dev->usbdev,
usb_rcvbulkpipe(dev->usbdev,
dev->bulkin_endpoint_addr[ep_num - 1]),
urb->transfer_buffer,
skb->len,
rsi_rx_done_handler,
rx_cb);
status = usb_submit_urb(urb, mem_flags);
if (status) {
rsi_dbg(ERR_ZONE, "%s: Failed in urb submission\n", __func__);
dev_kfree_skb(skb);
}
return status;
}
static int rsi_usb_read_register_multiple(struct rsi_hw *adapter, u32 addr,
u8 *data, u16 count)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
u8 *buf;
u16 transfer;
int status;
if (!addr)
return -EINVAL;
buf = kzalloc(RSI_USB_BUF_SIZE, GFP_KERNEL);
if (!buf)
return -ENOMEM;
while (count) {
transfer = min_t(u16, count, RSI_USB_BUF_SIZE);
status = usb_control_msg(dev->usbdev,
usb_rcvctrlpipe(dev->usbdev, 0),
USB_VENDOR_REGISTER_READ,
RSI_USB_REQ_IN,
((addr & 0xffff0000) >> 16),
(addr & 0xffff), (void *)buf,
transfer, USB_CTRL_GET_TIMEOUT);
if (status < 0) {
rsi_dbg(ERR_ZONE,
"Reg read failed with error code :%d\n",
status);
kfree(buf);
return status;
}
memcpy(data, buf, transfer);
count -= transfer;
data += transfer;
addr += transfer;
}
kfree(buf);
return 0;
}
/**
* rsi_usb_write_register_multiple() - This function writes multiple bytes of
* information to multiple registers.
* @adapter: Pointer to the adapter structure.
* @addr: Address of the register.
* @data: Pointer to the data that has to be written.
* @count: Number of multiple bytes to be written on to the registers.
*
* Return: status: 0 on success, a negative error code on failure.
*/
static int rsi_usb_write_register_multiple(struct rsi_hw *adapter, u32 addr,
u8 *data, u16 count)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
u8 *buf;
u16 transfer;
int status = 0;
buf = kzalloc(RSI_USB_BUF_SIZE, GFP_KERNEL);
if (!buf)
return -ENOMEM;
while (count) {
transfer = min_t(u16, count, RSI_USB_BUF_SIZE);
memcpy(buf, data, transfer);
status = usb_control_msg(dev->usbdev,
usb_sndctrlpipe(dev->usbdev, 0),
USB_VENDOR_REGISTER_WRITE,
RSI_USB_REQ_OUT,
((addr & 0xffff0000) >> 16),
(addr & 0xffff),
(void *)buf,
transfer,
USB_CTRL_SET_TIMEOUT);
if (status < 0) {
rsi_dbg(ERR_ZONE,
"Reg write failed with error code :%d\n",
status);
kfree(buf);
return status;
}
count -= transfer;
data += transfer;
addr += transfer;
}
kfree(buf);
return 0;
}
/**
*rsi_usb_host_intf_write_pkt() - This function writes the packet to the
* USB card.
* @adapter: Pointer to the adapter structure.
* @pkt: Pointer to the data to be written on to the card.
* @len: Length of the data to be written on to the card.
*
* Return: 0 on success, a negative error code on failure.
*/
static int rsi_usb_host_intf_write_pkt(struct rsi_hw *adapter,
u8 *pkt,
u32 len)
{
u32 queueno = ((pkt[1] >> 4) & 0x7);
u8 endpoint;
endpoint = ((queueno == RSI_WIFI_MGMT_Q || queueno == RSI_WIFI_DATA_Q ||
queueno == RSI_COEX_Q) ? WLAN_EP : BT_EP);
return rsi_write_multiple(adapter,
endpoint,
(u8 *)pkt,
len);
}
static int rsi_usb_master_reg_read(struct rsi_hw *adapter, u32 reg,
u32 *value, u16 len)
{
struct usb_device *usbdev =
((struct rsi_91x_usbdev *)adapter->rsi_dev)->usbdev;
u16 temp;
int ret;
ret = rsi_usb_reg_read(usbdev, reg, &temp, len);
if (ret < 0)
return ret;
*value = temp;
return 0;
}
static int rsi_usb_master_reg_write(struct rsi_hw *adapter,
unsigned long reg,
unsigned long value, u16 len)
{
struct usb_device *usbdev =
((struct rsi_91x_usbdev *)adapter->rsi_dev)->usbdev;
return rsi_usb_reg_write(usbdev, reg, value, len);
}
static int rsi_usb_load_data_master_write(struct rsi_hw *adapter,
u32 base_address,
u32 instructions_sz, u16 block_size,
u8 *ta_firmware)
{
u16 num_blocks;
u32 cur_indx, i;
u8 temp_buf[256];
int status;
num_blocks = instructions_sz / block_size;
rsi_dbg(INFO_ZONE, "num_blocks: %d\n", num_blocks);
for (cur_indx = 0, i = 0; i < num_blocks; i++, cur_indx += block_size) {
memcpy(temp_buf, ta_firmware + cur_indx, block_size);
status = rsi_usb_write_register_multiple(adapter, base_address,
(u8 *)(temp_buf),
block_size);
if (status < 0)
return status;
rsi_dbg(INFO_ZONE, "%s: loading block: %d\n", __func__, i);
base_address += block_size;
}
if (instructions_sz % block_size) {
memset(temp_buf, 0, block_size);
memcpy(temp_buf, ta_firmware + cur_indx,
instructions_sz % block_size);
status = rsi_usb_write_register_multiple
(adapter, base_address,
(u8 *)temp_buf,
instructions_sz % block_size);
if (status < 0)
return status;
rsi_dbg(INFO_ZONE,
"Written Last Block in Address 0x%x Successfully\n",
cur_indx);
}
return 0;
}
static struct rsi_host_intf_ops usb_host_intf_ops = {
.write_pkt = rsi_usb_host_intf_write_pkt,
.read_reg_multiple = rsi_usb_read_register_multiple,
.write_reg_multiple = rsi_usb_write_register_multiple,
.master_reg_read = rsi_usb_master_reg_read,
.master_reg_write = rsi_usb_master_reg_write,
.load_data_master_write = rsi_usb_load_data_master_write,
};
/**
* rsi_deinit_usb_interface() - This function deinitializes the usb interface.
* @adapter: Pointer to the adapter structure.
*
* Return: None.
*/
static void rsi_deinit_usb_interface(struct rsi_hw *adapter)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
rsi_kill_thread(&dev->rx_thread);
usb_free_urb(dev->rx_cb[0].rx_urb);
if (adapter->priv->coex_mode > 1)
usb_free_urb(dev->rx_cb[1].rx_urb);
kfree(dev->tx_buffer);
}
static int rsi_usb_init_rx(struct rsi_hw *adapter)
{
struct rsi_91x_usbdev *dev = adapter->rsi_dev;
struct rx_usb_ctrl_block *rx_cb;
u8 idx, num_rx_cb;
num_rx_cb = (adapter->priv->coex_mode > 1 ? 2 : 1);
for (idx = 0; idx < num_rx_cb; idx++) {
rx_cb = &dev->rx_cb[idx];
rx_cb->rx_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!rx_cb->rx_urb) {
rsi_dbg(ERR_ZONE, "Failed alloc rx urb[%d]\n", idx);
goto err;
}
rx_cb->ep_num = idx + 1;
rx_cb->data = (void *)dev;
}
skb_queue_head_init(&dev->rx_q);
rsi_init_event(&dev->rx_thread.event);
if (rsi_create_kthread(adapter->priv, &dev->rx_thread,
rsi_usb_rx_thread, "RX-Thread")) {
rsi_dbg(ERR_ZONE, "%s: Unable to init rx thrd\n", __func__);
goto err;
}
return 0;
err:
usb_free_urb(dev->rx_cb[0].rx_urb);
if (adapter->priv->coex_mode > 1)
usb_free_urb(dev->rx_cb[1].rx_urb);
return -1;
}
/**
* rsi_init_usb_interface() - This function initializes the usb interface.
* @adapter: Pointer to the adapter structure.
* @pfunction: Pointer to USB interface structure.
*
* Return: 0 on success, a negative error code on failure.
*/
static int rsi_init_usb_interface(struct rsi_hw *adapter,
struct usb_interface *pfunction)
{
struct rsi_91x_usbdev *rsi_dev;
int status;
rsi_dev = kzalloc(sizeof(*rsi_dev), GFP_KERNEL);
if (!rsi_dev)
return -ENOMEM;
adapter->rsi_dev = rsi_dev;
rsi_dev->usbdev = interface_to_usbdev(pfunction);
rsi_dev->priv = (void *)adapter;
if (rsi_find_bulk_in_and_out_endpoints(pfunction, adapter)) {
status = -EINVAL;
goto fail_eps;
}
adapter->device = &pfunction->dev;
usb_set_intfdata(pfunction, adapter);
rsi_dev->tx_buffer = kmalloc(2048, GFP_KERNEL);
if (!rsi_dev->tx_buffer) {
status = -ENOMEM;
goto fail_eps;
}
if (rsi_usb_init_rx(adapter)) {
rsi_dbg(ERR_ZONE, "Failed to init RX handle\n");
status = -ENOMEM;
goto fail_rx;
}
rsi_dev->tx_blk_size = 252;
adapter->block_size = rsi_dev->tx_blk_size;
/* Initializing function callbacks */
adapter->check_hw_queue_status = rsi_usb_check_queue_status;
adapter->determine_event_timeout = rsi_usb_event_timeout;
adapter->rsi_host_intf = RSI_HOST_INTF_USB;
adapter->host_intf_ops = &usb_host_intf_ops;
#ifdef CONFIG_RSI_DEBUGFS
/* In USB, one less than the MAX_DEBUGFS_ENTRIES entries is required */
adapter->num_debugfs_entries = (MAX_DEBUGFS_ENTRIES - 1);
#endif
rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__);
return 0;
fail_rx:
kfree(rsi_dev->tx_buffer);
fail_eps:
return status;
}
static int usb_ulp_read_write(struct rsi_hw *adapter, u16 addr, u32 data,
u16 len_in_bits)
{
int ret;
ret = rsi_usb_master_reg_write
(adapter, RSI_GSPI_DATA_REG1,
((addr << 6) | ((data >> 16) & 0xffff)), 2);
if (ret < 0)
return ret;
ret = rsi_usb_master_reg_write(adapter, RSI_GSPI_DATA_REG0,
(data & 0xffff), 2);
if (ret < 0)
return ret;
/* Initializing GSPI for ULP read/writes */
rsi_usb_master_reg_write(adapter, RSI_GSPI_CTRL_REG0,
RSI_GSPI_CTRL_REG0_VALUE, 2);
ret = rsi_usb_master_reg_write(adapter, RSI_GSPI_CTRL_REG1,
((len_in_bits - 1) | RSI_GSPI_TRIG), 2);
if (ret < 0)
return ret;
msleep(20);
return 0;
}
static int rsi_reset_card(struct rsi_hw *adapter)
{
int ret;
rsi_dbg(INFO_ZONE, "Resetting Card...\n");
rsi_usb_master_reg_write(adapter, RSI_TA_HOLD_REG, 0xE, 4);
/* This msleep will ensure Thread-Arch processor to go to hold
* and any pending dma transfers to rf in device to finish.
*/
msleep(100);
ret = rsi_usb_master_reg_write(adapter, SWBL_REGOUT,
RSI_FW_WDT_DISABLE_REQ,
RSI_COMMON_REG_SIZE);
if (ret < 0) {
rsi_dbg(ERR_ZONE, "Disabling firmware watchdog timer failed\n");
goto fail;
}
if (adapter->device_model != RSI_DEV_9116) {
ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_1,
RSI_ULP_WRITE_2, 32);
if (ret < 0)
goto fail;
ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_2,
RSI_ULP_WRITE_0, 32);
if (ret < 0)
goto fail;
ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_DELAY_TIMER_1,
RSI_ULP_WRITE_50, 32);
if (ret < 0)
goto fail;
ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_DELAY_TIMER_2,
RSI_ULP_WRITE_0, 32);
if (ret < 0)
goto fail;
ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_ENABLE,
RSI_ULP_TIMER_ENABLE, 32);
if (ret < 0)
goto fail;
} else {
ret = rsi_usb_master_reg_write(adapter,
NWP_WWD_INTERRUPT_TIMER,
NWP_WWD_INT_TIMER_CLKS,
RSI_9116_REG_SIZE);
if (ret < 0)
goto fail;
ret = rsi_usb_master_reg_write(adapter,
NWP_WWD_SYSTEM_RESET_TIMER,
NWP_WWD_SYS_RESET_TIMER_CLKS,
RSI_9116_REG_SIZE);
if (ret < 0)
goto fail;
ret = rsi_usb_master_reg_write(adapter,
NWP_WWD_MODE_AND_RSTART,
NWP_WWD_TIMER_DISABLE,
RSI_9116_REG_SIZE);
if (ret < 0)
goto fail;
}
rsi_dbg(INFO_ZONE, "Reset card done\n");
return ret;
fail:
rsi_dbg(ERR_ZONE, "Reset card failed\n");
return ret;
}
/**
* rsi_probe() - This function is called by kernel when the driver provided
* Vendor and device IDs are matched. All the initialization
* work is done here.
* @pfunction: Pointer to the USB interface structure.
* @id: Pointer to the usb_device_id structure.
*
* Return: 0 on success, a negative error code on failure.
*/
static int rsi_probe(struct usb_interface *pfunction,
const struct usb_device_id *id)
{
struct rsi_hw *adapter;
struct rsi_91x_usbdev *dev;
u16 fw_status;
int status;
rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__);
adapter = rsi_91x_init(dev_oper_mode);
if (!adapter) {
rsi_dbg(ERR_ZONE, "%s: Failed to init os intf ops\n",
__func__);
return -ENOMEM;
}
adapter->rsi_host_intf = RSI_HOST_INTF_USB;
status = rsi_init_usb_interface(adapter, pfunction);
if (status) {
rsi_dbg(ERR_ZONE, "%s: Failed to init usb interface\n",
__func__);
goto err;
}
rsi_dbg(ERR_ZONE, "%s: Initialized os intf ops\n", __func__);
if (id->idProduct == RSI_USB_PID_9113) {
rsi_dbg(INIT_ZONE, "%s: 9113 module detected\n", __func__);
adapter->device_model = RSI_DEV_9113;
} else if (id->idProduct == RSI_USB_PID_9116) {
rsi_dbg(INIT_ZONE, "%s: 9116 module detected\n", __func__);
adapter->device_model = RSI_DEV_9116;
} else {
rsi_dbg(ERR_ZONE, "%s: Unsupported RSI device id 0x%x\n",
__func__, id->idProduct);
status = -ENODEV;
goto err1;
}
dev = adapter->rsi_dev;
status = rsi_usb_reg_read(dev->usbdev, FW_STATUS_REG, &fw_status, 2);
if (status < 0)
goto err1;
else
fw_status &= 1;
if (!fw_status) {
rsi_dbg(INIT_ZONE, "Loading firmware...\n");
status = rsi_hal_device_init(adapter);
if (status) {
rsi_dbg(ERR_ZONE, "%s: Failed in device init\n",
__func__);
goto err1;
}
rsi_dbg(INIT_ZONE, "%s: Device Init Done\n", __func__);
}
status = rsi_rx_urb_submit(adapter, WLAN_EP, GFP_KERNEL);
if (status)
goto err1;
if (adapter->priv->coex_mode > 1) {
status = rsi_rx_urb_submit(adapter, BT_EP, GFP_KERNEL);
if (status)
goto err_kill_wlan_urb;
}
return 0;
err_kill_wlan_urb:
rsi_rx_urb_kill(adapter, WLAN_EP);
err1:
rsi_deinit_usb_interface(adapter);
err:
rsi_91x_deinit(adapter);
rsi_dbg(ERR_ZONE, "%s: Failed in probe...Exiting\n", __func__);
return status;
}
/**
* rsi_disconnect() - This function performs the reverse of the probe function,
* it deinitialize the driver structure.
* @pfunction: Pointer to the USB interface structure.
*
* Return: None.
*/
static void rsi_disconnect(struct usb_interface *pfunction)
{
struct rsi_hw *adapter = usb_get_intfdata(pfunction);
if (!adapter)
return;
rsi_mac80211_detach(adapter);
if (IS_ENABLED(CONFIG_RSI_COEX) && adapter->priv->coex_mode > 1 &&
adapter->priv->bt_adapter) {
rsi_bt_ops.detach(adapter->priv->bt_adapter);
adapter->priv->bt_adapter = NULL;
}
if (adapter->priv->coex_mode > 1)
rsi_rx_urb_kill(adapter, BT_EP);
rsi_rx_urb_kill(adapter, WLAN_EP);
rsi_reset_card(adapter);
rsi_deinit_usb_interface(adapter);
rsi_91x_deinit(adapter);
rsi_dbg(INFO_ZONE, "%s: Deinitialization completed\n", __func__);
}
#ifdef CONFIG_PM
static int rsi_suspend(struct usb_interface *intf, pm_message_t message)
{
/* Not yet implemented */
return -ENOSYS;
}
static int rsi_resume(struct usb_interface *intf)
{
/* Not yet implemented */
return -ENOSYS;
}
#endif
static const struct usb_device_id rsi_dev_table[] = {
{ USB_DEVICE(RSI_USB_VENDOR_ID, RSI_USB_PID_9113) },
{ USB_DEVICE(RSI_USB_VENDOR_ID, RSI_USB_PID_9116) },
{ /* Blank */},
};
static struct usb_driver rsi_driver = {
.name = "RSI-USB WLAN",
.probe = rsi_probe,
.disconnect = rsi_disconnect,
.id_table = rsi_dev_table,
#ifdef CONFIG_PM
.suspend = rsi_suspend,
.resume = rsi_resume,
#endif
};
module_usb_driver(rsi_driver);
MODULE_AUTHOR("Redpine Signals Inc");
MODULE_DESCRIPTION("Common USB layer for RSI drivers");
MODULE_DEVICE_TABLE(usb, rsi_dev_table);
MODULE_FIRMWARE(FIRMWARE_RSI9113);
MODULE_VERSION("0.1");
MODULE_LICENSE("Dual BSD/GPL");