| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2020, Konrad Dybcio |
| */ |
| |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| thermal-zones { |
| pm660l-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&pm660l_temp>; |
| |
| trips { |
| pm660l_alert0: pm660l-alert0 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| pm660l_crit: pm660l-crit { |
| temperature = <125000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| |
| pmic@2 { |
| compatible = "qcom,pm660l", "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm660l_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm660l_gpios: gpio@c000 { |
| compatible = "qcom,pm660l-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pm660l_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@3 { |
| compatible = "qcom,pm660l", "qcom,spmi-pmic"; |
| reg = <0x3 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm660l_lpg: pwm { |
| compatible = "qcom,pm660l-lpg"; |
| |
| status = "disabled"; |
| }; |
| |
| pm660l_wled: leds@d800 { |
| compatible = "qcom,pm660l-wled"; |
| reg = <0xd800>, <0xd900>; |
| interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "ovp", "short"; |
| label = "backlight"; |
| |
| status = "disabled"; |
| }; |
| |
| pm660l_spmi_regulators: regulators { |
| compatible = "qcom,pm660l-regulators"; |
| }; |
| }; |
| }; |
| |
